The Nomadik clocksource driver has had a bad define making it
impossible to use it for sched_clock() for a while. Fix this
and also enable it for the Nomadik.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The nomadik multiplatform support made it possible to select
MACH_NOMADIK_8815NHK without selecting ARCH_NOMADIK, which leads
to build errors when we also select ARMv6/v7 targets. Adding the
ifdef here restores the intended behavior.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This deletes the leftover <mach/timex.h> and <mach/uncompress.h>
and Makefile.boot that have no role in a multiplatform
environment.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This converts the Nomadik to run in multiplatform mode, including
the defconfig change. After this the "uImage" target in the kernel
tree will no longer work, but we do not care about this. Instead
we generate the uImage from the zImage using mkimage or update
the bootloader to accept bootz. Some minor updates to the defconfig
are done as part of this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This header is not used any more after the platform was switched
to obtain resources from the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These are device tree conversions for a number of platforms,
with the intention of turning code from board files into
device tree descriptions. Notable changes are:
* davinci bindings for pinctrl, MTD, RTC, watchdog and i2c
* nomadik bindings for all devices, removing the board files
* bcm2835 bindings for mmc and i2c
* tegra bindings for hdmi, keyboard, audio, as well as some updates
* at91 bindings for hardware ecc and for devices on RM9200
* mxs bindings for cfa100xx
* sunxi support for Miniand Hackberry board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=NLEa
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree conversions from Arnd Bergmann:
"These are device tree conversions for a number of platforms, with the
intention of turning code from board files into device tree
descriptions. Notable changes are:
- davinci bindings for pinctrl, MTD, RTC, watchdog and i2c
- nomadik bindings for all devices, removing the board files
- bcm2835 bindings for mmc and i2c
- tegra bindings for hdmi, keyboard, audio, as well as some updates
- at91 bindings for hardware ecc and for devices on RM9200
- mxs bindings for cfa100xx
- sunxi support for Miniand Hackberry board"
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (72 commits)
Revert "sunxi: a10-cubieboard: Add user LEDs to the device tree"
Revert "sunxi: a13-olinuxino: Add user LED to the device tree"
clk: tegra: initialise parent of uart clocks
ARM: tegra: remove clock-frequency properties from serial nodes
clk: tegra: fix driver to match DT binding
clk: tegra: local arrays should be static
clk: tegra: Add missing spinlock for hclk and pclk
clk: tegra: Implement locking for super clock
clk: tegra: fix wrong clock index between se to sata_cold
sunxi: a13-olinuxino: Add user LED to the device tree
ARM: davinci: da850 DT: add support for machine reboot
ARM: davinci: da850: add wdt DT node
ARM: davinci: da850: add DT node for I2C0
ARM: at91: at91sam9n12: add DT parameters to enable PMECC
ARM: at91: at91sam9x5: add DT parameters to enable PMECC
ARM: at91: add EMAC bindings to RM9200 DT
ARM: at91: add SSC bindings to RM9200 DT
ARM: at91: add MMC bindings to RM9200 DT
ARM: at91: Animeo IP: enable watchdog support
ARM: nomadik: fix OF compilation regression
...
are unused on ARM architecure. Samsung has some code setting up wdog
in arch_decomp_wdog(). But since CONFIG_S3C_BOOT_WATCHDOG is defined
nowhere, it will not run. Otherwise, system can not boot at all when
wdog is set up but no one pats it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQ9WSiAAoJEFBXWFqHsHzOkpYH/iHOomqWknjg0YjeUKmoqnk+
UnAiP/OD0pOuqdC3izSq5rAaxeCn2ESYhXWdHH3LQFNnhwDPOItagY3T1dBgJH0G
KvO3wDj0K1jUM6Nzt4hta4pnCc/KClyCcVjYrP5pE+bs3NzOzxvfj2tPc81lI0Iy
rnkMLWw6gVRllhecUezt3TOd/GfI7NwuyjjBOLelOerbImWFqLOCNIZSRQlazbyS
hFh4OkR7yoU6vEvPdmS4B4A5PWBHlxiUS6Wr4v+doGFPiFgR05tJodLnnJ/KGWmG
LFY99MyeBvcgiUlFcUpiVLYpWJh+7IB1LJH+IGNJbWFYC+Yvn/o9IRYO8kvuiYE=
=weNJ
-----END PGP SIGNATURE-----
Merge tag 'cleanup-decompwdog-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/cleanup
From Shawn Guo:
The series cleans up ARCH_HAS_DECOMP_WDOG and arch_decomp_wdog which
are unused on ARM architecure. Samsung has some code setting up wdog
in arch_decomp_wdog(). But since CONFIG_S3C_BOOT_WATCHDOG is defined
nowhere, it will not run. Otherwise, system can not boot at all when
wdog is set up but no one pats it.
* tag 'cleanup-decompwdog-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: samsung: remove unused arch_decomp_wdog() code
ARM: remove unused arch_decomp_wdog()
ARM: decompress: remove unused ARCH_HAS_DECOMP_WDOG
Signed-off-by: Olof Johansson <olof@lixom.net>
This was only used from the core machine, source it into the machine
file and delete, also convert all direct references using the
physical-to-virtual macros in this file to ioremap() and only
default-remap the 4K used by the debug UART.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Device Tree support on Nomadik can do everything the old board
files could do, so delete the old board files and make the nomadik
select CONFIG_OF.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves over the MMC/SD card support to the device tree probe
path. The special GPIO to bias the card detect line is kept,
but the pin property is moved to the device tree as part of
the MMC/SD card node.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This converts the SMSC91x ethernet controller to use device
tree. The existing solution from the board file, to request the
GPIO triggering the ethernet IRQ from the board file is kept
for the time being, but the GPIO number assignment is moved
over to the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the instances of the Nomadik pin controller and the
Nomadik GPIO blocks (also handled by the GPIO driver) over to
the device tree. A new compatible string is added to the
pin control driver in the process.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the FSMC NAND driver and flash partitions to the Nomadik
device tree.
The only compatible string accepted by this driver is currently
"st,spear600-fsmc-nand" which is inappropriate for this system, so
this patch adds the compatible value "stericsson,fsmc-nand" as
well.
Cc: linux-mtd@vger.kernel.org
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The two remaining PrimeCells, RNG and RTC, are migrated to the
device tree for device tree boot.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the pinctrl maps over to the CPU file and register them
right before the pin controller itself. This way the pinmaps
will also benefit the device tree boot.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Support basic device tree boot on the Nomadik. Implement the
support in the cpu file with the intent of deleting the board
files later. At this stage IRQ controllers, system timer,
l2x0 cache, UARTs and thus console boot is fully functional.
Patch out the code adding devices by initcalls for now so
as not to disturb the boot.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The I2C pins were still set up using custom nmk_* calls, move
these to use the pinctrl mapping table instead. There was also
a remaining call to turn the Ethernet pin to GPIO, and this is
now done implicitly by the GPIO-to-pinctrl range translation
calls.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This creates irqchip initialization infrastructure from Thomas
Petazzoni. The VIC and GIC irqchip code is moved to drivers/irqchips
and adapted to use the new infrastructure. All DT enabled platforms
using GIC and VIC are converted over to use the new irqchip_init.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQ8ZobAAoJEMhvYp4jgsXiihIH/2VvxmSHZb0e3jN6AR0B42b7
9EwX0IE0B23t91hNTwdzzmTJQYA7pMmWkgHNfd3vIeqSepJAmrVv/gp4iM9CtPwE
KNh+kDWOK2ZsOH4Vb0lYRJHN8WQOIQHuCUr9+MdYLNOgf/pPL6G/Y9kv9A1e7fTC
W+tFRjC5N1ilZMGyowX12L1wnwDk6kHzed6YV6bskC17cZ9/pg8PhSVbM4A/3kAv
NXYKqbXJb+eCsWGXg/knZXOL6V9gBwvVYoe4O9X3nQ0226AWB9caad8l8tchAjRB
fmrYF1tbkpOWPnLxhvQy5b5MJichJgTMJHh7RgiEcc/3f63kOljjlx4QKiqHvT0=
=q7gm
-----END PGP SIGNATURE-----
Merge tag 'gic-vic-to-irqchip' of git://sources.calxeda.com/kernel/linux into next/cleanup
From Rob Herring:
Initial irqchip init infrastructure and GIC and VIC clean-ups
This creates irqchip initialization infrastructure from Thomas
Petazzoni. The VIC and GIC irqchip code is moved to drivers/irqchips
and adapted to use the new infrastructure. All DT enabled platforms
using GIC and VIC are converted over to use the new irqchip_init.
* tag 'gic-vic-to-irqchip' of git://sources.calxeda.com/kernel/linux:
irqchip: Move ARM vic.h to include/linux/irqchip/arm-vic.h
ARM: picoxcell: use common irqchip_init function
ARM: spear: use common irqchip_init function
irqchip: Move ARM VIC to drivers/irqchip
ARM: samsung: remove unused tick.h
ARM: remove unneeded vic.h includes
ARM: remove mach .handle_irq for VIC users
ARM: VIC: set handle_arch_irq in VIC initialization
ARM: VIC: shrink down vic.h
irqchip: Move ARM gic.h to include/linux/irqchip/arm-gic.h
ARM: use common irqchip_init for GIC init
irqchip: Move ARM GIC to drivers/irqchip
ARM: remove mach .handle_irq for GIC users
ARM: GIC: set handle_arch_irq in GIC initialization
ARM: GIC: remove direct use of gic_raise_softirq
ARM: GIC: remove assembly ifdefs from gic.h
ARM: mach-ux500: use SGI0 to wake up the other core
arm: add set_handle_irq() to register the parent IRQ controller handler function
irqchip: add basic infrastructure
irqchip: add to the directories part of the IRQ subsystem in MAINTAINERS
Fixed up massive merge conflicts with the timer cleanup due to adjacent changes:
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-bcm/board_bcm.c
arch/arm/mach-cns3xxx/cns3420vb.c
arch/arm/mach-ep93xx/adssphere.c
arch/arm/mach-ep93xx/edb93xx.c
arch/arm/mach-ep93xx/gesbc9312.c
arch/arm/mach-ep93xx/micro9.c
arch/arm/mach-ep93xx/simone.c
arch/arm/mach-ep93xx/snappercl15.c
arch/arm/mach-ep93xx/ts72xx.c
arch/arm/mach-ep93xx/vision_ep9307.c
arch/arm/mach-highbank/highbank.c
arch/arm/mach-imx/mach-imx6q.c
arch/arm/mach-msm/board-dt-8960.c
arch/arm/mach-netx/nxdb500.c
arch/arm/mach-netx/nxdkn.c
arch/arm/mach-netx/nxeb500hmi.c
arch/arm/mach-nomadik/board-nhk8815.c
arch/arm/mach-picoxcell/common.c
arch/arm/mach-realview/realview_eb.c
arch/arm/mach-realview/realview_pb1176.c
arch/arm/mach-realview/realview_pb11mp.c
arch/arm/mach-realview/realview_pba8.c
arch/arm/mach-realview/realview_pbx.c
arch/arm/mach-socfpga/socfpga.c
arch/arm/mach-spear13xx/spear1310.c
arch/arm/mach-spear13xx/spear1340.c
arch/arm/mach-spear13xx/spear13xx.c
arch/arm/mach-spear3xx/spear300.c
arch/arm/mach-spear3xx/spear310.c
arch/arm/mach-spear3xx/spear320.c
arch/arm/mach-spear3xx/spear3xx.c
arch/arm/mach-spear6xx/spear6xx.c
arch/arm/mach-tegra/board-dt-tegra20.c
arch/arm/mach-tegra/board-dt-tegra30.c
arch/arm/mach-u300/core.c
arch/arm/mach-ux500/board-mop500.c
arch/arm/mach-ux500/cpu-db8500.c
arch/arm/mach-versatile/versatile_ab.c
arch/arm/mach-versatile/versatile_dt.c
arch/arm/mach-versatile/versatile_pb.c
arch/arm/mach-vexpress/v2m.c
include/asm-generic/vmlinux.lds.h
Clockevent cleanup series from Shawn Guo.
Resolved move/change conflict in mach-pxa/time.c due to the sys_timer
cleanup.
* clocksource/cleanup:
clocksource: use clockevents_config_and_register() where possible
ARM: use clockevents_config_and_register() where possible
clockevents: export clockevents_config_and_register for module use
+ sync to Linux 3.8-rc3
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-pxa/time.c
Now that we have VIC moved to drivers/irqchip and all VIC DT init for
platforms using irqchip_init, move gic.h and update the remaining
includes.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Alessandro Rubini <rubini@unipv.it>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: STEricsson <STEricsson_nomadik_linux@list.st.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: linux-samsung-soc@vger.kernel.org
Numerous includes of asm/hardware/vic.h aren't needed, so remove them.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Hubert Feurstein <hubert.feurstein@contec.at>
Cc: Alessandro Rubini <rubini@unipv.it>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: STEricsson <STEricsson_nomadik_linux@list.st.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Acked-By: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: linux-samsung-soc@vger.kernel.org
Cc: patches@opensource.wolfsonmicro.com
Acked-by: Arnd Bergmann <arnd@arndb.de>
Now that the VIC initialization sets up the handle_arch_irq pointer, we
can remove it for all machines and make it static. Move vic_handle_irq
to avoid a forward declaration.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Hubert Feurstein <hubert.feurstein@contec.at>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: STEricsson <STEricsson_nomadik_linux@list.st.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
With ARCH_HAS_DECOMP_WDOG removed from arch/arm/boot/compressed/decompress.c,
all the arch_decomp_wdog() definition at platform level is unneeded.
Remmove it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Bump the IRQ numbers from offset at 1 (right above NO_IRQ)
to 32. This is the painful way to learn that if you're using
SPARSE_IRQ and avoid to define .nr_irqs in your machine,
the first 16 IRQs will be pre-allocated, and the IRQdomain
code (as the VIC core code before it) will then assume
that all IRQ descriptors are pre-allocated, and 16 of them
are - by somebody else. So mapping the IRQs will fail in
irq_create_mapping(). Moving the offset upward rids us of
this problem.
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reference to the old include header for the FSMC NAND
MTD driver was somehow left in place, get rid of it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that the only field in struct sys_timer is .init, delete the struct,
and replace the machine descriptor .timer field with the initialization
function itself.
This will enable moving timer drivers into drivers/clocksource without
having to place a public prototype of each struct sys_timer object into
include/linux; the intent is to create a single of_clocksource_init()
function that determines which timer driver to initialize by scanning
the device dtree, much like the proposed irqchip_init() at:
http://www.spinics.net/lists/arm-kernel/msg203686.html
Includes mach-omap2 fixes from Igor Grinberg.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
- Various cleanups especially in NAND tests
- Add support for NAND flash on BCMA bus
- DT support for sh_flctl and denali NAND drivers
- Kill obsolete/superceded drivers (fortunet, nomadik_nand)
- Fix JFFS2 locking bug in ENOMEM failure path
- New SPI flash chips, as usual
- Support writing in 'reliable mode' for DiskOnChip G4
- Debugfs support in nandsim
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAlDSAa4ACgkQdwG7hYl686MMcACeNYa//ghPtccb5L+IRXsqaFDL
Yi4AoLWOaOjN8qM4KUF/bfMEkwNGAePz
=DaAQ
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20121219' of git://git.infradead.org/linux-mtd
Pull MTD updates from David Woodhouse:
- Various cleanups especially in NAND tests
- Add support for NAND flash on BCMA bus
- DT support for sh_flctl and denali NAND drivers
- Kill obsolete/superceded drivers (fortunet, nomadik_nand)
- Fix JFFS2 locking bug in ENOMEM failure path
- New SPI flash chips, as usual
- Support writing in 'reliable mode' for DiskOnChip G4
- Debugfs support in nandsim
* tag 'for-linus-20121219' of git://git.infradead.org/linux-mtd: (96 commits)
mtd: nand: typo in nand_id_has_period() comments
mtd: nand/gpio: use io{read,write}*_rep accessors
mtd: block2mtd: throttle writes by calling balance_dirty_pages_ratelimited.
mtd: nand: gpmi: reset BCH earlier, too, to avoid NAND startup problems
mtd: nand/docg4: fix and improve read of factory bbt
mtd: nand/docg4: reserve bb marker area in ecclayout
mtd: nand/docg4: add support for writing in reliable mode
mtd: mxc_nand: reorder part_probes to let cmdline override other sources
mtd: mxc_nand: fix unbalanced clk_disable() in error path
mtd: nandsim: Introduce debugfs infrastructure
mtd: physmap_of: error checking to prevent a NULL pointer dereference
mtg: docg3: potential divide by zero in doc_write_oob()
mtd: bcm47xxnflash: writing support
mtd: tests/read: initialize buffer for whole next page
mtd: at91: atmel_nand: return bit flips for the PMECC read_page()
mtd: fix recovery after failed write-buffer operation in cfi_cmdset_0002.c
mtd: nand: onfi need to be probed in 8 bits mode
mtd: nand: add NAND_BUSWIDTH_AUTO to autodetect bus width
mtd: nand: print flash size during detection
mted: nand_wait_ready timeout fix
...
Due to a clash between refactoring and due to loss of a header
file that remained in my working tree the Nomadik stopped
compiling after switching to the FSMC driver. This patch fixes
it up.
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The Nomadik NAND driver is really just a subset of the existing
FSMC driver, so let's switch over to using that driver instead,
since it handles more variants of this chip. The callbacks for
setting up the chip is doing stuff now handled by the FSMC
driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This converts the Nomadik and Ux500 platforms to use SPARSE_IRQ.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the MTU timer driver from arch/arm/plat-nomadik
to drivers/clocksource and moves the header file to the
platform_data directory.
As this moves the last file being compiled to an object out
of arch/arm/plat-nomadik, we have to "turn off the light"
and delete the plat-nomadik directory, because it is not
allowed to have an empty Makefile in a plat-* directory.
This is probably also a desired side effect of depopulating
the arch/arm directory of drivers. Luckily we have just
deleted all the <plat/*> include files prior to this so
by moving the last one we may delete the directory.
After this all the Ux500 and Nomadik device drivers live
outside of the arch/arm hierarchy.
Cc: Alessandro Rubini <rubini@unipv.it>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to convert the MTU timer to work with sparse IRQ we need
to pass the IRQ used when initializing instead of just letting
it rely on a special name being used in the IRQ header file.
Cc: Alessandro Rubini <rubini@unipv.it>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This merges the old <plat/pincfg.h> header into
<linux/platform_data/pinctrl-nomadik.h> and rids us of
yet one more <plat/*> include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the platform data header for the Nomadik pin controller
to <linux/platform_data/pinctrl-nomadik.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As suggested by Andrew Morton:
This is a pet peeve of mine. Any time there's a long list of items
(header file inclusions, kconfig entries, array initalisers, etc) and
someone wants to add a new item, they *always* go and stick it at the
end of the list.
Guys, don't do this. Either put the new item into a randomly-chosen
position or, probably better, alphanumerically sort the list.
lets sort all our select statements alphanumerically. This commit was
created by the following perl:
while (<>) {
while (/\\\s*$/) {
$_ .= <>;
}
undef %selects if /^\s*config\s+/;
if (/^\s+select\s+(\w+).*/) {
if (defined($selects{$1})) {
if ($selects{$1} eq $_) {
print STDERR "Warning: removing duplicated $1 entry\n";
} else {
print STDERR "Error: $1 differently selected\n".
"\tOld: $selects{$1}\n".
"\tNew: $_\n";
exit 1;
}
}
$selects{$1} = $_;
next;
}
if (%selects and (/^\s*$/ or /^\s+help/ or /^\s+---help---/ or
/^endif/ or /^endchoice/)) {
foreach $k (sort (keys %selects)) {
print "$selects{$k}";
}
undef %selects;
}
print;
}
if (%selects) {
foreach $k (sort (keys %selects)) {
print "$selects{$k}";
}
}
It found two duplicates:
Warning: removing duplicated S5P_SETUP_MIPIPHY entry
Warning: removing duplicated HARDIRQS_SW_RESEND entry
and they are identical duplicates, hence the shrinkage in the diffstat
of two lines.
We have four testers reporting success of this change (Tony, Stephen,
Linus and Sekhar.)
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- Add subdrivers for the DB8540 and NHK8815 Nomadik-type ASICs,
provide platform config for the Nomadik.
- Add a driver for the i.MX35.
- Add a driver for the BCM2835, an advanced GPIO expander.
- Various fixes and clean-ups and minor improvements for the core,
Nomadik, pinctr-single, sirf drivers.
- Some platform config for the ux500.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=g2i2
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl changes from Linus Walleij:
"Some of this stuff is hitting arch/arm/* and have been ACKed by the
ARM SoC folks, or it's device tree bindings pertaining to the specific
driver.
These are the bulk pinctrl changes for kernel v3.7:
- Add subdrivers for the DB8540 and NHK8815 Nomadik-type ASICs,
provide platform config for the Nomadik.
- Add a driver for the i.MX35.
- Add a driver for the BCM2835, an advanced GPIO expander.
- Various fixes and clean-ups and minor improvements for the core,
Nomadik, pinctr-single, sirf drivers.
- Some platform config for the ux500."
* tag 'pinctrl-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (27 commits)
pinctrl: add bcm2835 driver
pinctrl: clarify idle vs sleep states
pinctrl/nomadik: use irq_find_mapping()
pinctrl: sirf: add lost chained_irq_enter and exit in sirfsoc_gpio_handle_irq
pinctrl: sirf: initialize the irq_chip pointer of pinctrl_gpio_range
pinctrl: sirf: fix spinlock deadlock in sirfsoc_gpio_set_input
pinctrl: sirf: add missing pins to pinctrl list
pinctrl: sirf: fix a typo in sirfsoc_gpio_probe
pinctrl: pinctrl-single: add debugfs pin h/w state info
ARM: ux500: 8500: update I2C sleep states pinctrl
pinctrl: Fix potential memory leak in pinctrl_register_one_pin()
ARM: ux500: tidy up pin sleep modes
ARM: ux500: fix spi2 pin group
pinctrl: imx: remove duplicated const
pinctrl: document semantics vs GPIO
ARM: ux500: 8500: use hsit_a_2 group for HSI
pinctrl: use kasprintf() in pinmux_request_gpio()
pinctrl: pinctrl-single: Add pinctrl-single,bits type of mux
pinctrl/nomadik : add MC1_a_2 pin MC1 function group list
pinctrl: pinctrl-single: Make sure we do not change bits outside of mask
...
This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot of
driver/platform shared definitions have gone, such as platform data
structures. They now need to move out to a common location instead,
and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move and
once it settles in, we should be good for quite a while. Sorry for the
overhead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Tc6y
-----END PGP SIGNATURE-----
Merge tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc multiplatform enablement from Olof Johansson:
"This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot
of driver/platform shared definitions have gone, such as platform
data structures. They now need to move out to a common location
instead, and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move
and once it settles in, we should be good for quite a while. Sorry
for the overhead."
Fix conflicts as per Olof.
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits)
ARM: add v7 multi-platform defconfig
ARM: msm: Move core.h contents into common.h
ARM: highbank: call highbank_pm_init from .init_machine
ARM: dtb: move all dtb targets to common Makefile
ARM: spear: move platform_data definitions
ARM: samsung: move platform_data definitions
ARM: orion: move platform_data definitions
ARM: vexpress: convert to multi-platform
ARM: initial multiplatform support
ARM: mvebu: move armada-370-xp.h in mach dir
ARM: vexpress: remove dependency on mach/* headers
ARM: picoxcell: remove dependency on mach/* headers
ARM: move all dtb targets out of Makefile.boot
ARM: picoxcell: move debug macros to include/debug
ARM: socfpga: move debug macros to include/debug
ARM: mvebu: move debug macros to include/debug
ARM: vexpress: move debug macros to include/debug
ARM: highbank: move debug macros to include/debug
ARM: move debug macros to common location
ARM: make mach/gpio.h headers optional
...
This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used with
a mainline kernel. We have not been able to find anyone interested
in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ck1u
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc general cleanups from Olof Johansson:
"This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used
with a mainline kernel. We have not been able to find anyone
interested in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above."
Fix up some conflicts with the staging tree (and because nxp4008 was
removed)
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (184 commits)
ARM: OMAP2+: serial: Change MAX_HSUART_PORTS to 6
ARM: OMAP4: twl-common: Support for additional devices on i2c1 bus
ARM: mmp: using for_each_set_bit to simplify the code
ARM: tegra: harmony: fix ldo7 regulator-name
ARM: OMAP2+: Make omap4-keypad.h local
ARM: OMAP2+: Make l4_3xxx.h local
ARM: OMAP2+: Make l4_2xxx.h local
ARM: OMAP2+: Make l3_3xxx.h local
ARM: OMAP2+: Make l3_2xxx.h local
ARM: OMAP1: Move irda.h from plat to mach
ARM: OMAP2+: Make hdq1w.h local
ARM: OMAP2+: Make gpmc-smsc911x.h local
ARM: OMAP2+: Make gpmc-smc91x.h local
ARM: OMAP1: Move flash.h from plat to mach
ARM: OMAP2+: Make debug-devices.h local
ARM: OMAP1: Move board-voiceblue.h from plat to mach
ARM: OMAP1: Move board-sx1.h from plat to mach
ARM: OMAP2+: Make omap-wakeupgen.h local
ARM: OMAP2+: Make omap-secure.h local
ARM: OMAP2+: Make ctrl_module_wkup_44xx.h local
...
The nhk8815 board files uses NAND_NO_READRDY in its platform data, but
this macro is getting removed because it was not being used anywhere.
Without this patch, building nhk8815_defconfig results in:
arch/arm/mach-nomadik/board-nhk8815.c:118:6: error: 'NAND_NO_READRDY' undeclared here (not in a function)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: Linus Walleij <linus.walleij@linaro.org>
ARM is moving to stricter checks on readl/write functions,
so we need to use the correct types everywhere.
Acked-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: STEricsson <STEricsson_nomadik_linux@list.st.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Most platforms don't need mach/gpio.h and it prevents multi-platform
kernel images. Add CONFIG_NEED_MACH_GPIO_H and make platforns select it
if they need gpio.h. This is platforms that define __GPIOLIB_COMPLEX
or have lots of implicit includes pulled in by mach/gpio.h.
at91 and omap have gpio clean-up pending and can drop
CONFIG_NEED_MACH_GPIO_H once that is in.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the nomadik include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: STEricsson <STEricsson_nomadik_linux@list.st.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Andreas Westin <andreas.westin@stericsson.com>
This converts the Nomadik to using pin control using the
driver for the STN8815 ASIC.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since the VIC was converted to use generic IRQ domains IRQ 0
is silently ignored. This IRQ is used on the Nomadik so we're
missing it now. Bump all IRQ numbers by one since they are
now decoupled from the hardware IRQ numbers.
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This registers the MMC device for the Nomadik so we can access
MMC/SD cards, which is pretty nice.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add board data to register all the Nomadik I2C devices.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Nomadik has two dedicated I2C bus blocks for I2C0 and I2C1,
and a bitbanged GPIO connection on two pins for the USB portions
of the STw4811 chip. Register all three as bit-banged GPIO for
the moment.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove more custom stuff by simply converting the Nomadik machine
to use generic clocks and move the driver to drivers/clk.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mike Turquette <mturquette@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij