OMAP4 has an AES module that uses the omap-aes crypto driver.
Add DT entries for the same.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Set pinmux_emmc_pins mux mode for cmd line to MODE2 in order
to detect eMMC on BBB and BBW + eMMC cape.
Signed-off-by: Balaji T K <balajitk@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The IGEP AQUILA EXPANSION board is a development platform
for the IGEP COM AQUILA AM335x boards.
The board adds the following connectivity:
o USB OTG
o USB HOST
o HDMI
o Ethernet
o Serial Debug (3.3V)
o 2x46 pin headers
o EEPROM
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The IGEP COM AQUILA is industrial processors SODIMM module with
following highlights:
o AM3352/AM3354/AM3358/AM3359 Texas Instruments processor
o Cortex-A8 ARM CPU
o 3.3 volts Inputs / Outputs use industrial
o 256 MB DDR3 SDRAM / 128 Megabytes FLASH
o MicroSD card reader on-board
o Ethernet controller on-board
o JTAG debug connector available
o Designed for industrial range purposes
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
3.3V fixed regulator does not belong to TPS node - as a result
the fixed regulator is never probed and MMC is continually deferred
due to lack of regulator.
Move the fixed regulator to be at root of platform.
Cc: Joel Fernandes <joelf@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Tested-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add information about the USB OTG PHY. Without this
the OTG port on beagle will not work.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Provide RESET GPIO and Power regulator for the USB PHY,
the USB Host port mode and the PHY device for the controller.
Also provide pin multiplexer information for USB host pins.
We also relocate omap3_pmx_core pin definations so that they
are close to omap3_pmx_wkup pin definations.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
We no longer need to model the RESET line as a regulator since
the USB phy-nop driver accepts "reset-gpios" property.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
We no longer need to model the RESET line as a regulator since
the USB phy-nop driver accepts "reset-gpios" property.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
We no longer need to model the RESET line as a regulator since
the USB phy-nop driver accepts "reset-gpios" property.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Set the alias for ethernet0 and ethernet1 so that uBoot
can set the MAC address appropriately.
Currently u-boot cannot find the alias and there for does
not set the MAC address.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add DT nodes for TPS659038 PMIC on DRA7 boards.
It is based on top of:
http://comments.gmane.org/gmane.linux.ports.arm.omap/102459.
Documentation:
- Documentation/devicetree/bindings/mfd/palmas.txt
- Documentation/devicetree/bindings/regulator/palmas-pmic.txt
Boot Tested on DRA7 d1 Board.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
[bcousson@baylibre.com: Fix indentation and changelog]
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
"gpmc,sync-clki-ps" is not defined/documented, it should be
"gpmc,sync-clk-ps" instead.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The On Chip Peripherals (OCP) device node is a simplified
representation of the AM33XX SoC interconnect. An OCP dev
node is already defined in the am33xx.dtsi Device Tree
source file included by am33xx based boards so there is
no need to redefine this on each board DT file.
Also, the OCP and IP modules directly connected to it are SoC
internal details that is better to keep outside of board files.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
am33xx boards DTS include the am33xx.dtsi Device Tree
source file that already define a pinmux device node for
the AM33XX SoC Pin Multiplex.
Redefining this for each board makes the Device Tree files
harder to modify and maintain so let's just use what is
already defined in the included .dtsi file.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
This matches the vendor 3.8.x configuration that is shipping
with the boards.
The LED layout is now:
USR0: heartbeat
USR1: mmc0 (micro-SD slot)
USR2: cpu0
USR3: mmc1 (eMMC)
The cpu0 triggers was put in between the mmc triggers to make
is easier to see where the disk activity is.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Tested-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The micro-SD slot hooks up all four data pins so lets' use them.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Tested-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The pinmux is specified in am335x-bone-common.dtsi to be
reused by the eMMC cape.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Tested-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
[bcousson@baylibre.com: Fix traling spaces and useless comments]
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
This enables the use of MMC cards even when no card was inserted at boot.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Tested-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Adds AM33XX MMC support for am335x-bone, am335x-evm and am335x-evmsk boards.
Also added is the DMA binding definitions based on the generic DMA request
binding.
Additional changes made to DTS:
* Interrupt, reg and compatible properties added
* ti,needs-special-hs-handling added
Signed-off-by: Matt Porter <mporter@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Adds DMA resources to the AM33XX SPI nodes.
Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Joel A Fernandes <joelagnel@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Adds AM33XX EDMA support to the am33xx.dtsi as documented in
Documentation/devicetree/bindings/dma/ti-edma.txt
[Joel Fernandes <joelf@ti.com>]
Drop DT entries that are non-hardware-description as discussed in [1]
[1] https://patchwork.kernel.org/patch/2226761/
Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Joel A Fernandes <joelagnel@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Without this node, there will be no palmas driver to notify
dwc3 that a cable has been connected and, without that, dwc3
will never initialize.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[kishon@ti.com: added dt properties for enabling vbus/id interrupts
and fixed vbus-supply value after SMPS10 is modeled as 2 regulators]
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Use a common naming scheme "mode0name.modename flags" for the
USB host pins to be consistent.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
This adds devicetree for gta04 (Openmoko next generation board) with necessary
support for mmc, usb, leds and button.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Populate uarts, timers, rtc, wdt, gpio, i2c, spi, cpsw & pwm nodes.
Reason for adding these nodes early - hwmod code required address
space of peripherals corresponding to these nodes (as address space
details are removed from hwmod database).
uart0, timers - 1 & 2 and synctimer were already present, so here the
remaining uarts & timers are added.
All properties as per the existing binding has been added for uart,
timer, rtc, wdt & gpio. Even though that was not the current scope
of work, felt adding those would reduce or require no effort later
to get these peripherals working.
For i2c, spi, cpsw & pwm - only the properties that were sure to be
correct has been added (main intention is to make hwmod happy and
avoid any later modification to here added properties).
While at it add "ti,hwmod" property to already existing nodes.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Update AM4372 cpu node to the latest cpus/cpu bindings for ARM.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add minimal device tree source needed for DRA7 based SoCs.
Also add a board dts file for the dra7-evm (based on dra752)
which contains 1.5G of memory with 1G interleaved and 512MB
non-interleaved. Also added in the board file are pin configuration
details for i2c, mcspi and uart devices on board.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The OMAP4 SoC family uses specially-designed PMIC (power management IC)
companion chip for power management needs: TWL6030/TWL6032.
Therefore there is a typical connection of PMIC to OMAP4 so we can
move it into separate .dtsi file and do not duplicate over
board-specific files.
Tested on OMAP4 SDP board and Pandaboard ES2.
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
SMPS10 has two outputs OUT1 and OUT2. Hence SMPS10 is modeled as
two regulators. The DT node is split to reflect it.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Following commit ff5c9059 and therefore other omap platforms using
the gpio-omap driver correct the #interrupt-cells property on am33xx
too. The omap gpio binding documentaion also states that
the #interrupt-cells property should be 2.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
ARM Performance Monitor Units are available on the am33xx,
add the support in the dtsi.
Tested with perf and oprofile on a regular beaglebone.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The IGEP COM MOdule has a GPIO LED connected to OMAP
pins. Configure this pin as output GPIO.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The IGEPv2 has a number of GPIO LED connected to OMAP
pins. Configure these pins as output GPIO.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
IGEP boards have a number of LED connected to OMAP or TWL GPIO
lines. The actual wiring is different on each board so each board
DT has need to configure the mux correctly.
Even though it works with the current DT, the kernel complains with:
[2.305023] leds-gpio leds.18: pins are not configured from the driver
Add an empty pinmux_leds_pins pinctrl child node so boards can
override with the correct mux configuration and not depend on
default values for the GPIO LEDs to work.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
This adds device tree with necessary support to boot with functional
video (on both emulator and real N900 device).
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
MMCONFIG
Revert "x86/PCI: MMCONFIG: Check earlier for MMCONFIG region at address zero"
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJST3wYAAoJEFmIoMA60/r8GlIP/An+r2j9679vAH7Iuk0wkIRi
0NLv0j7RdcdwbM7gXfeMc+EGzrLwDhbsnP60S5iKT2CfJ1n1buDe/na4fO9/MDaH
prMDhDzRs9MrdLIhv0l/ovyoFiITWEvVoLngxDU9WjUIHWsFGQ1asIP+bpk8+t/m
zZ5xHm6eczoaBtcPbeQUI/vXqKuC78koZMs979Nk7y8Py/br5xX9uqzyWMFWkx5u
C1DvREEDFPHtde9e1jKr1G+Pzn1M0W8CItEKCfUNev70ob244m+0HsQN698Bniqp
p+rzBBM3XXGvuOuemHrz8x0Fomkn8G6vL1D3PXL8hWvuwiKrO95HGKCCbn2VCT+g
OgUZ9QkOCEJpCD3A7ET3sV1iFdoeMNXk/iwQpPvIrkr50m0C6LLOmO7yaTUcLhJu
Aa3x4r+KG5rzKfNT8vPCEC2TY1IL2O6bZvmRubzSocxc8SUfQ+92vmnSd9G169hN
0X5ljIlAFFhfNOvf6dRljD2zCji2WeteRyBO3k3Flk+L/EnHD1Vi5jYrLoVaFJIH
NB4lx/szysElE6IzDOwtTlTR6v0fWdygHnnUlr6yELZyifNaYk1Z2lNASxi5JzBG
LlcxavTgNs1a90aEuzVpc94XTdMZDV0bNb4H36I0aKXU/tlSt2fbKAqMoLvDISJL
hQBRNKAOF2ep2Htg96Zs
=LqLn
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.12-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"We merged what was intended to be an MMCONFIG cleanup, but in fact,
for systems without _CBA (which is almost everything), it broke
extended config space for domain 0 and it broke all config space for
other domains.
This reverts the change"
* tag 'pci-v3.12-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "x86/PCI: MMCONFIG: Check earlier for MMCONFIG region at address zero"
This reverts commit 07f9b61c39.
07f9b61c was intended to be a cleanup that didn't change anything, but in
fact, for systems without _CBA (which is almost everything), it broke
extended config space for domain 0 and all config space for other domains.
Reference: http://lkml.kernel.org/r/20131004011806.GE20450@dangermouse.emea.sgi.com
Reported-by: Hedi Berriche <hedi@sgi.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pull MIPS fixes from Ralf Baechle:
"Two small fixes for 3.12 only this week. I have a few more fixes
pending but those are conceptually more complex so will have to wait
for a bit longer"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix forgotten preempt_enable() when CPU has inclusive pcaches
MIPS: Alchemy: MTX-1: fix incorrect placement of __initdata tag
Pull x86 fixes from Ingo Molnar:
"Two simplefb fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/simplefb: Mark framebuffer mem-resources as IORESOURCE_BUSY to avoid bootup warning
x86/simplefb: Fix overflow causing bogus fall-back
Pull ARC fix from Vineet Gupta:
"Chrisitian found/fixed issue with SA_SIGINFO based signal handler
corrupting the user space registers post after signal handling"
* 'for-curr' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: Fix signal frame management for SA_SIGINFO
Pull powerpc fixes from Ben Herrenschmidt:
"Here are a few powerpc fixes, all aimed at -stable, found in part
thanks to the ramping up of a major distro testing and in part thanks
to the LE guys hitting all sort interesting corner cases.
The most scary are probably the register clobber issues in
csum_partial_copy_generic(), especially since Anton even had a test
case for that thing, which didn't manage to hit the bugs :-)
Another highlight is that memory hotplug should work again with these
fixes.
Oh and the vio modalias one is worse than the cset implies as it
upsets distro installers, so I've been told at least, which is why I'm
shooting it to stable"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/tm: Switch out userspace PPR and DSCR sooner
powerpc/tm: Turn interrupts hard off in tm_reclaim()
powerpc/perf: Fix handling of FAB events
powerpc/vio: Fix modalias_show return values
powerpc/iommu: Use GFP_KERNEL instead of GFP_ATOMIC in iommu_init_table()
powerpc/sysfs: Disable writing to PURR in guest mode
powerpc: Restore registers on error exit from csum_partial_copy_generic()
powerpc: Fix parameter clobber in csum_partial_copy_generic()
powerpc: Fix memory hotplug with sparse vmemmap
When we do a treclaim or trecheckpoint we end up running with userspace
PPR and DSCR values. Currently we don't do anything special to avoid
running with user values which could cause a severe performance
degradation.
This patch moves the PPR and DSCR save and restore around treclaim and
trecheckpoint so that we run with user values for a much shorter period.
More care is taken with the PPR as it's impact is greater than the DSCR.
This is similar to user exceptions, where we run HTM_MEDIUM early to
ensure that we don't run with a userspace PPR values in the kernel.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We can't take IRQs in tm_reclaim as we might have a bogus r13 and r1.
This turns IRQs hard off in this function.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 4df4899 "Add power8 EBB support" included a bug in the handling
of the FAB_CRESP_MATCH and FAB_TYPE_MATCH fields.
These values are pulled out of the event code using EVENT_THR_CTL_SHIFT,
however we were then or'ing that value directly into MMCR1.
This meant we were failing to set the FAB fields correctly, and also
potentially corrupting the value for PMC4SEL. Leading to no counts for
the FAB events and incorrect counts for PMC4.
The fix is simply to shift left the FAB value correctly before or'ing it
with MMCR1.
Reported-by: Sooraj Ravindran Nair <soonair3@in.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
modalias_show() should return an empty string on error, not -ENODEV.
This causes the following false and annoying error:
> find /sys/devices -name modalias -print0 | xargs -0 cat >/dev/null
cat: /sys/devices/vio/4000/modalias: No such device
cat: /sys/devices/vio/4001/modalias: No such device
cat: /sys/devices/vio/4002/modalias: No such device
cat: /sys/devices/vio/4004/modalias: No such device
cat: /sys/devices/vio/modalias: No such device
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org>
Under heavy (DLPAR?) stress, we tripped this panic() in
arch/powerpc/kernel/iommu.c::iommu_init_table():
page = alloc_pages_node(nid, GFP_ATOMIC, get_order(sz));
if (!page)
panic("iommu_init_table: Can't allocate %ld bytes\n", sz);
Before the panic() we got a page allocation failure for an order-2
allocation. There appears to be memory free, but perhaps not in the
ATOMIC context. I looked through all the call-sites of
iommu_init_table() and didn't see any obvious reason to need an ATOMIC
allocation. Most call-sites in fact have an explicit GFP_KERNEL
allocation shortly before the call to iommu_init_table(), indicating we
are not in an atomic context. There is some indirection for some paths,
but I didn't see any locks indicating that GFP_KERNEL is inappropriate.
With this change under the same conditions, we have not been able to
reproduce the panic.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org>
arch/powerpc/kernel/sysfs.c exports PURR with write permission.
This may be valid for kernel in phyp mode. But writing to
the file in guest mode causes crash due to a priviledge violation
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org>
The csum_partial_copy_generic() function saves the PowerPC non-volatile
r14, r15, and r16 registers for the main checksum-and-copy loop.
Unfortunately, it fails to restore them upon error exit from this loop,
which results in silent corruption of these registers in the presumably
rare event of an access exception within that loop.
This commit therefore restores these register on error exit from the loop.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The csum_partial_copy_generic() uses register r7 to adjust the remaining
bytes to process. Unfortunately, r7 also holds a parameter, namely the
address of the flag to set in case of access exceptions while reading
the source buffer. Lacking a quantum implementation of PowerPC, this
commit instead uses register r9 to do the adjusting, leaving r7's
pointer uncorrupted.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Previous commit 46723bfa540... introduced a new config option
HAVE_BOOTMEM_INFO_NODE that ended up breaking memory hot-remove for ppc
when sparse vmemmap is not defined.
This patch defines HAVE_BOOTMEM_INFO_NODE for ppc and adds the call to
register_page_bootmem_info_node. Without this we get a BUG_ON for memory
hot remove in put_page_bootmem().
This also adds a stub for register_page_bootmem_memmap to allow ppc to build
with sparse vmemmap defined. Leaving this as a stub is fine since the same
vmemmap addresses are also handled in vmemmap_populate and as such are
properly mapped.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org> [v3.9+]
IORESOURCE_BUSY is used to mark temporary driver mem-resources
instead of global regions. This suppresses warnings if regions
overlap with a region marked as BUSY.
This was always the case for VESA/VGA/EFI framebuffer regions so
do the same for simplefb regions. The reason we do this is to
allow device handover to real GPU drivers like
i915/radeon/nouveau which get the same regions via PCI BARs.
Maybe at some point we will be able to unregister platform
devices properly during the handover. In this case the simplefb
region would get removed before the new region is created.
However, this is currently not the case and would require rather
huge changes in remove_conflicting_framebuffers(). Add the BUSY
marker now and try to eventually rewrite the handover for a next release.
Also see kernel/resource.c for more information:
/*
* if a resource is "BUSY", it's not a hardware resource
* but a driver mapping of such a resource; we don't want
* to warn for those; some drivers legitimately map only
* partial hardware resources. (example: vesafb)
*/
This suppresses warnings like:
------------[ cut here ]------------
WARNING: CPU: 2 PID: 199 at arch/x86/mm/ioremap.c:171 __ioremap_caller+0x2e3/0x390()
Info: mapping multiple BARs. Your kernel is fine.
Call Trace:
dump_stack+0x54/0x8d
warn_slowpath_common+0x7d/0xa0
warn_slowpath_fmt+0x4c/0x50
iomem_map_sanity_check+0xac/0xe0
__ioremap_caller+0x2e3/0x390
ioremap_wc+0x32/0x40
i915_driver_load+0x670/0xf50 [i915]
...
Reported-by: Tom Gundersen <teg@jklm.no>
Tested-by: Tom Gundersen <teg@jklm.no>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Link: http://lkml.kernel.org/r/1380724864-1757-1-git-send-email-dh.herrmann@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We have a fairly large batch of fixes this time around, mostly just due to
various platforms all having a fix or two more than usual.
Worth pointing out are:
- A fix for EDMA on Davinci/OMAP where channel allocation broke with
the DT conversion. Due to some miscommunication we didn't
understand the impact of the breakage, so we were pushing back on it
for 3.12, but it sounds like it's actually breaking quite a few people
out there.
- A bunch of fixes for Marvell platforms, some straggling fixes for
merge window fallout and some fixes for a couple of the platforms
(Netgear RN102 in particular).
- A fix for a race between multi-cluster power management and cpu hotplug
on Versatile Express.
And a bunch of other smaller fixes that all add up.
We'll be switching over into stricter regressions-only mode from here
on out.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=DLem
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We have a fairly large batch of fixes this time around, mostly just
due to various platforms all having a fix or two more than usual.
Worth pointing out are:
- A fix for EDMA on Davinci/OMAP where channel allocation broke with
the DT conversion. Due to some miscommunication we didn't
understand the impact of the breakage, so we were pushing back on
it for 3.12, but it sounds like it's actually breaking quite a few
people out there.
- A bunch of fixes for Marvell platforms, some straggling fixes for
merge window fallout and some fixes for a couple of the platforms
(Netgear RN102 in particular).
- A fix for a race between multi-cluster power management and cpu
hotplug on Versatile Express.
And a bunch of other smaller fixes that all add up.
We'll be switching over into stricter regressions-only mode from here
on out"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
ARM: multi_v7_defconfig: add SDHCI for i.MX
bus: mvebu-mbus: Fix optional pcie-mem/io-aperture properties
ARM: mvebu: add missing DT Mbus ranges and relocate PCIe DT nodes for RN102
ARM: at91: sam9g45: shutdown ddr1 too when rebooting
MAINTAINERS: ARM: SIRF: use kernel.org mail box
MAINTAINERS: ARM: SIRF: add missed drivers into maintain list
ARM: edma: Fix clearing of unused list for DT DMA resources
ARM: vexpress: tc2: fix hotplug/idle/kexec race on cluster power down
ARM: dts: sirf: fix interrupt and dma prop of VIP for prima2 and atlas6
ARM: dts: sirf: fix the ranges of peri-iobrg of prima2
ARM: dts: makefile: build atlas6-evb.dtb for ARCH_ATLAS6
ARM: dts: sirf: fix fifosize, clks, dma channels for UART
ARM: mvebu: Add DT entry for ReadyNAS 102 to use gpio-poweroff driver
ARM: mvebu: fix ReadyNAS 102 Power button GPIO to make it active high
ARM: mach-integrator: Add stub for pci_v3_early_init() for !CONFIG_PCI
ARM: shmobile: Remove #gpio-ranges-cells DT property
gpio: rcar: Remove #gpio-range-cells DT property usage
ARM: shmobile: armadillo: fixup ether pinctrl naming
ARM: shmobile: Lager: add Micrel KSZ8041 PHY fixup
ARM: shmobile: update SDHI DT compatibility string to the <unit>-<soc> format
...
Previously, when a signal was registered with SA_SIGINFO, parameters 2
and 3 of the signal handler were written to registers r1 and r2 before
the register set was saved. This led to corruption of these two
registers after returning from the signal handler (the wrong values were
restored).
With this patch, registers are now saved before any parameters are
passed, thus maintaining the processor state from before signal entry.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
- mvebu
- fix ReadyNAS 102 power button (needs to be active high)
- fix ReadyNAS 102 automated rebooting (prevent hang) by add gpio-poweroff
node
- fix booting ReadyNAS 102 by adding MBus ranges and PCIe DT nodes
- mvebu-mbus: prevent PCIe driver from continuing with corrupted resource
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)
iQEcBAABAgAGBQJSTERhAAoJEAi3KVZQDZAeFaQH/jmhAZwvSrB7MeTTY7J9eAcl
n4cFHImBiSb6IdDaocKB+yOmEgq/X2LS/DjK71sa0+CQsTq9B5nHxMHioogdUrG7
S8ofIjqu90CBOZ1I5IMSPmA3uOc1B2+wYi9uLxmajMTzYVDDBEZh9LuMy/GjwzU2
/g09RedQ3XkWDVv3pdPdEiC6KZ/gg7gejxOLv0nv9ydxr0DB8/VwmBHWFC0ghawB
3EchoagJ3M+mAbUaxtY6cauV2nnAJOO5mV6ZHl2tIOj4/Mhn8Le/C1t+Zcdf+U82
iAvqWmiRc3Vk96g8xXZWwZoPL7vhidLcE7dpOIZ2ymq5+g3esTaailqRxRqS9+c=
=uNPR
-----END PGP SIGNATURE-----
Merge tag 'fixes-3.12-2' of git://git.infradead.org/linux-mvebu into fixes
From Jason Cooper:
mvebu fixes for v3.12 (round 2)
- mvebu
- fix ReadyNAS 102 power button (needs to be active high)
- fix ReadyNAS 102 automated rebooting (prevent hang) by add gpio-poweroff
node
- fix booting ReadyNAS 102 by adding MBus ranges and PCIe DT nodes
- mvebu-mbus: prevent PCIe driver from continuing with corrupted resource
* tag 'fixes-3.12-2' of git://git.infradead.org/linux-mvebu:
bus: mvebu-mbus: Fix optional pcie-mem/io-aperture properties
ARM: mvebu: add missing DT Mbus ranges and relocate PCIe DT nodes for RN102
ARM: mvebu: Add DT entry for ReadyNAS 102 to use gpio-poweroff driver
ARM: mvebu: fix ReadyNAS 102 Power button GPIO to make it active high
Signed-off-by: Olof Johansson <olof@lixom.net>
Turn on SDHCI for i.MX support so machines can boot with local rootfs
on SD. Tested on a Wandboard Quad.
Signed-off-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Commit ebd97be635 ('PCI: remove ARCH_SUPPORTS_MSI kconfig option')
removes the ARCH_SUPPORTS_MSI Kconfig option that allowed
architectures to indicate whether they support PCI MSI or not. Now,
PCI MSI support can be compiled in on any architecture thanks to the
use of weak functions thanks to 4287d824f2 ('PCI: use weak functions
for MSI arch-specific functions').
So, architecture specific code is now responsible to ensure that its
PCI MSI code builds in all cases, or be appropriately conditionally
compiled.
On Sparc, the MSI support is only provided for Sparc64, so the
ARCH_SUPPORTS_MSI kconfig option was only selected for SPARC64, and
not for the Sparc architecture as a whole. Therefore, removing
ARCH_SUPPORTS_MSI broke Sparc32 configurations with CONFIG_PCI_MSI=y,
because the Sparc-specific MSI code is not designed to be built on
Sparc32.
To solve this, this commit ensures that the Sparc MSI code is only
built on Sparc64. This is done thanks to a new Kconfig Makefile helper
option SPARC64_PCI_MSI, modeled after the existing SPARC64_PCI. The
SPARC64_PCI_MSI option is an hidden option that is true when both
Sparc64 PCI support is enabled and MSI is enabled. The
arch/sparc/kernel/pci_msi.c file is now only built when
SPARC64_PCI_MSI is true.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch proposes to remove the IRQF_DISABLED flag from sparc architecture
code. It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The length argument to strlcpy was still wrong. It could overflow the end of
full_boot_str by 5 bytes. Instead of strcat and strlcpy, just use snprint.
Reported-by: Brad Spengler <spender@grsecurity.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This config item already exists generically in lib/Kconfig.debug.
Remove the duplicate config in arm64.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
On my MacBook Air lfb_size is 4M, which makes the bitshit
overflow (to 256GB - larger than 32 bits), meaning we fall
back to efifb unnecessarily.
Cast to u64 to avoid the overflow.
Signed-off-by: Tom Gundersen <teg@jklm.no>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Link: http://lkml.kernel.org/r/1380644320-1026-1-git-send-email-teg@jklm.no
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull sparc fix from David Miller:
"Just a single bug fix to a regression added during some strlcpy()
conversions"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Fix buggy strlcpy() conversion in ldom_reboot().
Pull two KVM fixes from Gleb Natapov.
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: VMX: do not check bit 12 of EPT violation exit qualification when undefined
ARM: kvm: rename cpu_reset to avoid name clash
When 5e12a613 and 0cd3754a were introduced, Netgear ReadyNAS 102 .dts
file was queued for inclusion and missed the update to have Mbus (and
then BootROM) ranges properties declared. It also missed the relocation
of Armada 370/XP PCIe DT nodes introduced by 14fd8ed0 after de1af8d4.
This patch fixes that which makes 3.12-rc3 bootable on the NAS.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The FAULT_FLAG_WRITE flag has been set based on uninitialized variable.
Fixes a regression added by commit 759496ba64 ("arch: mm: pass
userspace fault flag to generic fault handler")
Signed-off-by: Felipe Pena <felipensp@gmail.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull AVR32 fixes from Hans-Christian Egtvedt.
Fix build warnings and use the Kbuild infrastructure for generic headers
rather than doing it by hand.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
avr32: cast syscall_return to silence compiler warning
avr32: fix clockevents kernel warning
avr32: use Kbuild infrastructure to handle the asm-generic headers
Pull S+core fixes from Lennox Wu:
"These updates include updating information of maintainers, fix some
trivial errors, and add a necessary function for supporting ipv6"
* tag 'for-linus-20130929' of git://github.com/sctscore/official-linux:
Score: Update the information of Score maintaners
Score: Modify the Makefile of Score, remove -mlong-calls for compiling
Score: Implement the function csum_ipv6_magic
Score: The commit is for compiling successfully
Like we are doing on DDR0 we need to cleanly shutdown DDR1 if it is
used before rebooting.
If DDR1 is not initialized, we check it and avoid dereferencing its address.
Even by adding two more instructions, we are able to complete the procedure
within a single cache line.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
HWMOD removal for MMC is breaking edma_start as the events are being manually
triggered due to unused channel list not being clear.
The above issue is fixed by reading the "dmas" property from the DT node if it
exists and clearing the bits in the unused channel list if the dma controller
used by any device is EDMA. For this purpose we use the of_* helpers to parse
the arguments in the dmas phandle list.
Also introduced is a minor clean up of a checkpatch error in old code.
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Reported-by: Balaji T K <balajitk@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Nishanth Menon <nm@ti.com>
Cc: Pantel Antoniou <panto@antoniou-consulting.com>
Cc: Jason Kridner <jkridner@beagleboard.org>
Cc: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
On the TC2 testchip, when all CPUs in a cluster enter standbywfi
and commit a power down request, the power controller will wait
for standbywfil2 coming from L2 cache controller to shut the
cluster down.
By the time all CPUs in a cluster commit a power down request
and enter wfi, the power controller cannot backtrack, or put it
another way, a CPU must not be allowed to complete execution
independently of the power controller, the only way for it to
resume properly must be upon wake-up IRQ pending and subsequent
reset triggered from the power controller.
Current MCPM back-end for TC2 disables the GIC CPU IF only when
power down is committed through the tc2_pm_suspend() method, that
makes sense since a suspended CPU is still online and can receive
interrupts whereas a hotplugged CPU, since it is offline,
migrated all IRQs and shutdown the per-CPU peripherals, hence
their PPIs.
The flaw with this reasoning is the following. If all CPUs in
a clusters are entering a power down state either through CPU
idle or CPU hotplug, when the last man successfully completes
the MCPM power down sequence (and executes wfi), power controller
waits for L2 wfi signal to quiesce the cluster and shut it down.
If, when all CPUs are sitting in wfi, an online CPU hotplugs back
in one of the CPUs in the cluster being shutdown, that CPU
receives an IPI that causes wfi to complete (since tc2_pm_down()
method does not disable the GIC CPU IF in that case - CPU being
hotplugged out, not idle) and the power controller will never see
the stanbywfil2 signal coming from L2 that is required for
shutdown to happen and the system deadlocks.
Further to this issue, kexec hotplugs secondary CPUs out during
kernel reload/restart.
Because kexec may (deliberately) trash the old kernel text, it is
not OK for CPUs to follow the MCPM soft reboot path, since
instructions after the WFI may have been replaced by kexec.
If tc2_pm_down() does not disable the GIC cpu interface, there is a
race between CPU powerdown in the old kernel and the IPI from the
new kernel that triggers secondary boot, particularly if the
powerdown is slow (due to L2 cache cleaning for example). If the
new kernel wins the race, the affected CPU(s) will not really be
reset and may execute garbage after the WFI.
The only solution to this problem consists in disabling the GIC
CPU IF on a CPU committed to power down regardless of the power
down entry method (CPU hotplug or CPU idle). This way, CPU wake-up
is under power controller control, which prevents unexpected wfi
exit caused by a pending IRQ.
This patch moves the GIC CPU IF disable call in the TC2 MCPM
implementation from the tc2_pm_suspend() method to the
tc2_pm_down() method to fix the mentioned race condition(s).
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Tested-by: Dave Martin <Dave.Martin@arm.com> (for kexec)
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
* Remove unused #gpio-ranges-cells DT property
* Remove usage of deprecated #gpio-range-cells DT property
from GPIO R-Car
Property was deprecated in v3.11-rc2
* Correct ether pinctl naming for armadillo800eva board
Regression introduced in v3.10-rc5
* Add Micrel KSZ8041 PHY fixup to lager board
This resolves a problem that has been present since 3.11-rc2
* Update SDHI DT compatibility string to the <unit>-<soc> format
This makes compatibility strings consistent across all renesas
hardware which currently supports DT.
The bindings which are being updated where intorodiced on
a per-SoC basis starting in v3.8-rc7. They may have
been internally consistent when originally added.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=WVMt
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes4-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
From Simon Horman:
Fourth Round of Renesas ARM based SoC fixes for v3.12
* Remove unused #gpio-ranges-cells DT property
* Remove usage of deprecated #gpio-range-cells DT property
from GPIO R-Car
Property was deprecated in v3.11-rc2
* Correct ether pinctl naming for armadillo800eva board
Regression introduced in v3.10-rc5
* Add Micrel KSZ8041 PHY fixup to lager board
This resolves a problem that has been present since 3.11-rc2
* Update SDHI DT compatibility string to the <unit>-<soc> format
This makes compatibility strings consistent across all renesas
hardware which currently supports DT.
The bindings which are being updated where intorodiced on
a per-SoC basis starting in v3.8-rc7. They may have
been internally consistent when originally added.
* tag 'renesas-fixes4-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Remove #gpio-ranges-cells DT property
gpio: rcar: Remove #gpio-range-cells DT property usage
ARM: shmobile: armadillo: fixup ether pinctrl naming
ARM: shmobile: Lager: add Micrel KSZ8041 PHY fixup
ARM: shmobile: update SDHI DT compatibility string to the <unit>-<soc> format
Signed-off-by: Olof Johansson <olof@lixom.net>
the current dts is lacking interrupt and dma prop for video input
processor of prima2 and atlas6, this patch fixes it.
Signed-off-by: Renwei Wu <Renwei.Wu@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
we lost an address range <0x56000000 0x56000000 0x1b00000> for peri-iobg
of prima2.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Makefile missed to include atlas6-evb.dtb for ARCH_ATLAS6.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
sirf uart and usp-based uart driver with full dma support has
hit 3.12, here we fix the fifosize, dma channels for some HW
prop.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Currently, development on arm64 is aided by a Foundation_v8 emulator
distributed by ARM [1]. To run their kernels, users will execute:
$ ./Foundation_v8 --image linux-system.axf --block-device raring-rootfs
To mount the raring-rootfs filesystem, the kernel parameter should
typically include:
root=/dev/vda
For this device to be present, the kernel must be compiled with
VIRTIO_{MMIO,BLK}. To make this work out-of-the-box, make it part of the
default configuration.
[1]: https://silver.arm.com/browse/FM00A
Cc: Will Deacon <will.deacon@arm.com>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Ramkumar Ramachandra <artagnon@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Most readily available root filesystems are formatted as EXT4 these
days. For example, see the raring rootfs that the Debian folk is
preparing [1].
[1]: http://people.debian.org/~wookey/bootstrap/rootfs/
Cc: Will Deacon <will.deacon@arm.com>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Ramkumar Ramachandra <artagnon@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Without that fix, at the end of the shutdown process, the board is
still powered (led glowing, fan running, ...).
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
NETGEAR ReadyNAS 102 Power button definition in .dts file flags
associated GPIO active low instead of active high. This results
in reversed events reported by input subsystem (0 returned when
the button is pressed, 1 when released). This patch makes
associated GPIO active high to recover correct behaviour.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
__initdata tag should be placed between the variable name and equal
sign for the variable to be placed in the intended .init.data section.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/5934/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The patch fixes the following compiler warning:
CC arch/avr32/kernel/process.o
arch/avr32/kernel/process.c: In function 'copy_thread':
arch/avr32/kernel/process.c:292: warning: assignment makes integer \
from pointer without a cast
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Since commit 01426478df
(avr32: Use generic idle loop) the kernel throws the
following warning on avr32:
WARNING: at 900322e4 [verbose debug info unavailable]
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 3.12.0-rc2 #117
task: 901c3ecc ti: 901c0000 task.ti: 901c0000
PC is at cpu_idle_poll_ctrl+0x1c/0x38
LR is at comparator_mode+0x3e/0x40
pc : [<900322e4>] lr : [<90014882>] Not tainted
sp : 901c1f74 r12: 00000000 r11: 901c74a0
r10: 901d2510 r9 : 00000001 r8 : 901db4de
r7 : 901c74a0 r6 : 00000001 r5 : 00410020 r4 : 901db574
r3 : 00410024 r2 : 90206fe0 r1 : 00000000 r0 : 007f0000
Flags: qvnzc
Mode bits: hjmde....G
CPU Mode: Supervisor
Call trace:
[<90039ede>] clockevents_set_mode+0x16/0x2e
[<90039f00>] clockevents_shutdown+0xa/0x1e
[<9003a078>] clockevents_exchange_device+0x58/0x70
[<9003a78c>] tick_check_new_device+0x38/0x54
[<9003a1a2>] clockevents_register_device+0x32/0x90
[<900035c4>] time_init+0xa8/0x108
[<90000520>] start_kernel+0x128/0x23c
When the 'avr32_comparator' clockevent device is registered,
the clockevent core sets the mode of that clockevent device
to CLOCK_EVT_MODE_SHUTDOWN. Due to this, the 'comparator_mode'
function calls the 'cpu_idle_poll_ctrl' to disables idle poll.
This results in the aforementioned warning because the polling
is not enabled yet.
Change the code to only disable idle poll if it is enabled by
the same function to avoid the warning.
Cc: stable@vger.kernel.org
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Use kbuild to add asm-generic headers that do nothing, also remove the arch
specific wrapper headers.
This only affects headers that do nothing but include the generic
equivalent. It does not touch any header that does a little more.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Pull scheduler, timer and x86 fixes from Ingo Molnar:
- A context tracking ARM build and functional fix
- A handful of ARM clocksource/clockevent driver fixes
- An AMD microcode patch level sysfs reporting fixlet
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
arm: Fix build error with context tracking calls
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: em_sti: Set cpu_possible_mask to fix SMP broadcast
clocksource: of: Respect device tree node status
clocksource: exynos_mct: Set IRQ affinity when the CPU goes online
arm: clocksource: mvebu: Use the main timer as clock source from DT
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/microcode/AMD: Fix patch level reporting for family 15h
Pull perf fixes from Ingo Molnar:
"A couple of tooling fixlets and a PMU detection printout fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86: Fix PMU detection printout when no PMU is detected
perf symbols: Demangle cloned functions
perf machine: Fix path unpopulated in machine__create_modules()
perf tools: Explicitly add libdl dependency
perf probe: Fix probing symbols with optimization suffix
perf trace: Add mmap2 handler
perf kmem: Make it work again on non NUMA machines
Pull s390 lockref enablement from Heiko Carstens:
"Enabling the new lockless lockref variant on s390 would have been
trivial until Tony Luck added a cpu_relax() call into the
CMPXCHG_LOOP(), with commit d472d9d98b ("lockref: Relax in cmpxchg
loop")
As already mentioned cpu_relax() is very expensive on s390 since it
yields() the current virtual cpu. So we are talking of several
thousand cycles. Considering this enabling the lockless lockref
variant would contradict the intention of the new semantics. And also
some quick measurements show performance regressions of 50% and more.
Simply removing the cpu_relax() call again seems also not very
desireable since Waiman Long reported that for some workloads the call
improved performance by 5%."
* 'lockref' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: enable ARCH_USE_CMPXCHG_LOCKREF
lockref: use arch_mutex_cpu_relax() in CMPXCHG_LOOP()
mutex: replace CONFIG_HAVE_ARCH_MUTEX_CPU_RELAX with simple ifdef
Clean-up to fix some warnings for !OF builds and spelling fixes in docs
- Clean-up openrisc prom.h
- Fix warnings caused by of_irq.h ifdefs
- Spelling fix for Synopsys
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSQk1CAAoJEMhvYp4jgsXilvEH/RztxbKNiscz7TYg3BDEKMaY
Wg029sdygyhl+Xb78FaS3Qwt98pK2JSWqzoNv+Tv4tfksGeLWVpe6HZlGvE/PEhb
2gUppV/ILyFSH8NfeaPkfyqdqr2XpCkcpkyGgYz7jQzNti5si448LC4oJR4tcXbo
FyKguRPpTtCwDsG86fPpQgc3fHK+C7W0oQu+PCB0DEk2ApMR05rGpPiMEYsKlj56
FE9n0DMZ+hfMCUivraVTyHB9Xjo4/kTv9s88hkjwkli+N3UrIUgOGsQpNt27QIFP
F95roRtVOmgRbgtMAFaEy7nfd+3QuVfonjfYNJzxpRHWew7LxFcVEwWRjb0zaKQ=
=KDHt
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree fixes from Rob Herring:
"Clean-up to fix some warnings for !OF builds and spelling fixes in
docs:
- Clean-up openrisc prom.h
- Fix warnings caused by of_irq.h ifdefs
- Spelling fix for Synopsys"
* tag 'devicetree-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dts: Fix misspelling of Synopsys
of: clean-up ifdefs in of_irq.h
openrisc: clean-up prom.h
Pull ARM fixes from Russell King:
"Just a few relatively small ARM fixes found since the last merge
window, nothing too exciting"
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7837/3: fix Thumb-2 bug in AES assembler code
ARM: only allow kernel mode neon with AEABI
ARM: 7839/1: entry: fix tracing of ARM-private syscalls
ARM: 7836/1: add __get_user_unaligned/__put_user_unaligned
Ran into this cryptic PMU bootup log recently:
[ 0.124047] Performance Events:
[ 0.125000] smpboot: ...
Turns out we print this if no PMU is detected. Fall back to
the right condition so that the following is printed:
[ 0.122381] Performance Events: no PMU driver, software events only.
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Link: http://lkml.kernel.org/n/tip-u2fwaUffakjp0qkpRfqljgsn@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Joel Fernandes