Add the Rockchip-sepcific dual-dsi setup and hook it into the VOP as well.
As described in the general dual-dsi devicetree binding, the panel should
define two input ports and point each of them to one of the used dsi-
controllers, as well as declare one of them as clock-master.
This is used to determine the dual-dsi state and get access to both
controller instances.
v6:
handle master+slave component in dsi-attach
v5:
use driver-internal mechanism to find dual dsi slave
v4:
add component directly in probe when adding empty dsi slave controller
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001123845.11818-8-heiko@sntech.de
Some Rockchip CRTCs, like rv1108 and px30, can directly output parallel
and serial RGB data to panel or conversion chip.
So add a feature-bit for vops to mark the ability for these direct
outputs and add an internal encoder in that case, that can attach to
bridge chipsor panels.
Changes in v7:
1. forget to delete rockchip_rgb_driver and delete it.
Changes in v6:
1. Update according to Heiko Stuebner' implemention, rgb output is
part of vop's feature, should not register as a independent
driver.
Changes in v5:
1. add SPDX-License-Identifier tag
Changes in v4:
1. add support px30;
Changes in v3:
1. update for rgb-mode move to panel node.
Changes in v2:
1. add error log when probe failed;
2. update name_to_output_mode() according to sean's suggest;
3. Fix uninitialized use of ret.
Signed-off-by: Sandy Huang <hjc@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180830211207.10480-3-heiko@sntech.de
Some encoder have a crc verification check, crc check fail if
input and output data is not equal.
That means encoder input and output need use same color depth,
vop can output 10bit data to encoder, but some panel only support
8bit depth, that would make crc check die.
So pre dither down vop data to 8bit if panel's bpc is 8.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
[seanpaul resolved conflict in rockchip_drm_vop.c]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-22-enric.balletbo@collabora.com
It's a hardware bug, all window's overlay channel reset
value is same, hardware overlay would be die.
so we must initial difference id for each overlay channel.
The Channel register is supported on all vop will full design.
Following is the details for this register
VOP_WIN0_CTRL2
bit[7:4] win_rid_win0_cbr
axi read id of win0 cbr channel
bit[3:0] win_rid_win0_yrgb
axi read id of win0 yrgb channel
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1501049980-6239-1-git-send-email-mark.yao@rock-chips.com
Vop Full framework now has following vops:
IP version chipname
3.1 rk3288
3.2 rk3368
3.4 rk3366
3.5 rk3399 big
3.6 rk3399 lit
3.7 rk3228
3.8 rk3328
The above IP version is from H/W define, some of vop support get
the IP version from VERSION_INFO register, some are not.
hardcode the IP version for each vop to identify them.
major version: used for IP structure, Vop full framework is 3,
vop little framework is 2.
minor version: on same structure, newer design vop will bigger
then old one.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1501049971-6131-1-git-send-email-mark.yao@rock-chips.com
In the hardware design process, the design of line flags
register is associated with the interrupt register,
placing the line flags in the interrupt definition is
more reasonable, and it would make multi-vop define easilier.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1501049960-6006-1-git-send-email-mark.yao@rock-chips.com
Since the drm atomic framework, only a small part of the vop
register needs sync write, Currently seems only following registers
need sync write:
cfg_done, standby and interrupt related register.
All ctrl registers are using the sync write method that is
inefficient, hardcode the write_relaxed flags to vop registers,
then can only do synchronize write for those actual needed register.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1501049953-5946-1-git-send-email-mark.yao@rock-chips.com
At present we are using init_table to initialize some
registers, but the Register init table use un-document define,
it is unreadable, and sometimes we only want to update tiny
bits, init table method is not friendly, it's diffcult to
reuse for difference chips.
To make it clean, initialize registers directly, and drops
init_table mechanism out.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1501049946-5877-1-git-send-email-mark.yao@rock-chips.com
Force vop output mode on encoder driver seem not a good idea,
EDP, HDMI, DisplayPort all have 10bit input on rk3399,
On non-10bit vop, vop 8bit output bit[0-7] connect to the
encoder high 8bit [2-9].
So force RGB10 to RGB888 on vop driver would be better.
And another problem, EDP check crtc id on atomic_check,
but encoder maybe NULL, so out_mode configure would fail,
it cause edp no display.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1495885416-22216-1-git-send-email-mark.yao@rock-chips.com
Add support for cdn DP controller which is embedded in the rk3399
SoCs. The DP is compliant with DisplayPort Specification,
Version 1.3, This IP is compatible with the rockchip type-c PHY IP.
There is a uCPU in DP controller, it need a firmware to work,
please put the firmware file to /lib/firmware/rockchip/dptx.bin. The
uCPU in charge of aux communication and link training, the host use
mailbox to communicate with the ucpu.
The dclk pin_pol of vop must not be invert for DP.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
[seanpaul fixed up some races between the worker and modeset]
[seanpaul squashed ~15 commits from chromium.org gerrit]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
[groeck fixed compilation errors when building as module]
Signed-off-by: Guenter Roeck <groeck@chromium.org>
VOP have integrated a hardware counter which indicate the exact display
line that vop is scanning. And if we're interested in a specific line,
we can set the line number to vop line_flag register, and then vop would
generate a line_flag interrupt for it.
For example eDP PSR function is interested in the vertical blanking
period, then driver could set the line number to zero.
This patch have exported a symbol that allow other driver to listen the
line flag event with given timeout limit:
- rockchip_drm_wait_line_flag()
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
There are two VOP in rk3399 chip, respectively VOP_BIG and VOP_LIT.
most registers layout of this two vop is same, their framework are both
VOP_FULL, the Major differences of this two is that:
VOP_BIG max output resolution is 4096x2160.
VOP_LIT max output resolution is 2560x1600
VOP_BIG support four windows.
VOP_LIT only support two windows.
RK3399 vop register layout is similar with rk3288, so some feature
can reuse with rk3288.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Some new vop register support mask, bit[16-31] is mask,
bit[0-15] is value, the mask is correspond to the value.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
[seanpaul masked 'v' per tfiga's review comments]
Reviewed-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
There are two version scale control register found on vop,
scale full version found on rk3288, support extension registers.
and scale little version found on rk3036, only support common scale.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
This patch adds the basic structure of a DRM Driver for Rockchip Socs.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Heiko Stuebner