If we need to force a full plane update before userspace/fbdev
have given us a proper plane state we should try to maintain the
current plane state as much as possible (apart from the parts
of the state we're trying to fix up with the plane update).
To that end add basic readout for the plane rotation and
maintain it during the initial fb takeover.
Cc: Hans de Goede <hdegoede@redhat.com>
Fixes: 516a49cc19 ("drm/i915: Fix assert_plane() warning on bootup with external display")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181120135450.3634-2-ville.syrjala@linux.intel.com
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
If we force a plane update to fix up our half populated plane state
we'll also force on the pipe gamma for the plane (since we always
enable pipe gamma currently). If the BIOS hasn't programmed a sensible
LUT into the hardware this will cause the image to become corrupted.
Typical symptoms are a purple/yellow/etc. flash when the driver loads.
To avoid this let's program something sensible into the LUT when
we do the plane update. In the future I plan to add proper plane
gamma enable readout so this is just a temporary measure.
Cc: Hans de Goede <hdegoede@redhat.com>
Fixes: 516a49cc19 ("drm/i915: Fix assert_plane() warning on bootup with external display")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181120135450.3634-1-ville.syrjala@linux.intel.com
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Depending on the transcoder enum values to translate from transcoder to
the corresponding CHICKEN_TRANS register can easily break if we add a
new transcoder. Add an explicit mapping instead, by using helpers to
look up the register instance either by transcoder or port (since
unconveniently the registers have both port and transcoder specific
bits).
While at it also check for the correctness of GEN, port, transcoder. I
wasn't sure if psr2_enabled can only be set for GEN9+, but that seems to
be the case indeed (see setting of sink_psr2_support in
intel_psr_init_dpcd()).
v2 (Ville):
- Make gen9_chicken_trans_reg() internal to intel_psr.c.
- s/trans/cpu_transcoder/
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181119180021.370-1-imre.deak@intel.com
Add a comment to the pipe and transcoder enum definitions about our
assumption in the code about enum values for pipes and transcoders
with a 1:1 transcoder -> pipe mapping.
v2:
- Clarify more what are the assumptions about the enum values. (Ville)
v3: (Lucas)
- s/->/ -> / so it looks less like pointer dereferencing.
- Use pipe enums as initializers in the transcoder enum definition.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v2)
Link: https://patchwork.freedesktop.org/patch/msgid/20181120092325.21249-3-imre.deak@intel.com
Depending on the transcoder enum values to translate from transcoder
to EDP PSR flags can easily break if we add a new transcoder. So remove
the dependency by using an explicit mapping.
While at it also add a WARN for unexpected trancoders.
v2:
- Simplify things by defining flag shift values instead of indices.
- s/trans/cpu_transcoder/ (Ville)
v3:
- Define flags to look like separate bits instead of the values of
the same bitfield. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181120092325.21249-2-imre.deak@intel.com
Depending on the transcoder enum values to translate from transcoder
to pipe/transcoder register addresses can easily break if we add a new
transcoder. So remove the dependency by using named initializers.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181120092325.21249-1-imre.deak@intel.com
Like it was done in commit 9e180d9991 ("drm/i915: Downgrade unknown
firmware warnings") for huc and guc: downgrade CSR firmware warnings. If
we have released no firmware yet for a platform, stop scaring the
consumer and merely note its expected absence.
By simply removing the warning and early return we hit the condition
with the appropriate message.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181117004234.23437-2-lucas.demarchi@intel.com
Before commit d8a5b7d79f ("drm/i915/csr: keep max firmware size together
with firmare name and version") it was possible to load the firmware for
testing purposes via parameter. Let's use the size of the last known
platform to recover that behavior.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181117004234.23437-1-lucas.demarchi@intel.com
Clean up fixed point temp variable initialization, use the more
conventional tmp name for temp variables, add empty lines before
return. No functional changes.
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181116120729.7580-5-jani.nikula@intel.com
Under moderate amounts of GPU stress, we can observe on Bearlake and
Pineview (later gen3 models) that we execute the following batch buffer
before the write into the batch is coherent. Adding extra (tested with
upto 32x) MI_FLUSH to either the invalidation, flush or both phases does
not solve the incoherency issue with the relocations, but emitting the
MI_STORE_DWORD_IMM twice does. So be it.
Fixes: 7dd4f6729f ("drm/i915: Async GPU relocation processing")
Testcase: igt/gem_tiled_fence_blits # blb/pnv
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181119154153.15327-1-chris@chris-wilson.co.uk
Since capturing the error state requires fiddling around with the GGTT
to read arbitrary buffers and is itself run under stop_machine(), it
deadlocks the machine (effectively a hard hang) when run in conjunction
with Broxton's VTd workaround to serialize GGTT access.
v2: Store the ERR_PTR in first_error so that the error can be reported
to the user via sysfs.
v3: Mention the quirk in dmesg (using info as per usual)
Fixes: 0ef34ad622 ("drm/i915: Serialize GTT/Aperture accesses on BXT")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Cc: John Harrison <john.C.Harrison@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181102161232.17742-5-chris@chris-wilson.co.uk
Hide the enable_gvt modparam in the default scenario where
support has not been compiled in.
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181116144447.7836-1-joonas.lahtinen@linux.intel.com
UAPI Changes:
- Add syncobj timeline support to drm.
Cross-subsystem Changes:
- Remove shared fence staging in dma-buf's fence object, and allow
reserving more than 1 fence and add more paranoia when debugging.
- Constify infoframe functions in video/hdmi.
Core Changes:
- Add vkms todo, and a lot of assorted doc fixes.
- Drop transitional helpers and convert drivers to use drm_atomic_helper_shutdown().
- Move atomic state helper functions to drm_atomic_state_helper.[ch]
- Refactor drm selftests, and add new tests.
- DP MST atomic state cleanups.
- Drop EXPORT_SYMBOL from drm leases.
- Lease cleanups and fixes.
- Create render node for vgem.
Driver Changes:
- Fix build failure in imx without fbdev emulation.
- Add rotation quirk for GPD win2 panel.
- Add support for various CDTech panels, Banana Pi Panel, DLC1010GIG,
Olimex LCD-O-LinuXino, Samsung S6D16D0, Truly NT35597 WQXGA,
Himax HX8357D, simulated RTSM AEMv8.
- Add dw_hdmi support to rockchip driver.
- Fix YUV support in vc4.
- Fix resource id handling in virtio.
- Make rockchip use dw-mipi-dsi bridge driver, and add dual dsi support.
- Advertise that tinydrm only supports DRM_FORMAT_MOD_LINEAR.
- Convert many drivers to use atomic helpers, and drm_fbdev_generic_setup().
- Add Mali linear tiled formats, and enable them in the Mali-DP driver.
- Add support for H6 DE3 mixer 0, DW HDMI, HDMI PHY and TCON TOP.
- Assorted driver cleanups and fixes.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEuXvWqAysSYEJGuVH/lWMcqZwE8MFAlvi0eAACgkQ/lWMcqZw
E8PI3g//TIlMmbrUc6BrWCNnz4YpJ+mC2dq7HMYB4yf5QeXTYrRDqK6syakbGcbe
FGYxt+21REfyQ9IQPdQslmVIUqJZuMBFSvLjXnZvybJSllE23CAXG0hEwHTuPYiF
yzxmYwlYOxVlW0nnB3fEDM8BfbWyMYR03c4sobPgiAGoBd+CJif/BtKEwranYrRx
7rZh8PnrCPGAnewmYux6U4zkOpWyjUp5t3kqpNRJDxPfxpa991yvUJX3DxTFFr9b
nqYNp3F3fkdowYuJj2eH/uBNd17TouzITGQxIZWEsJfFvB+2Awp7KgRCT8nUAt0I
vELbADsy3QwZlQp1F2FaVwfGbmHr41F+Vsq9coUt4vPaiyT3vCW0KGCeal1dKyYf
+S8UXIijkoGXm0RqxkbkJsG7AYSIzG+NQm6W+9tnQg6CwpQb2wqU3YCPQWqtFHqM
Tz/EW+JqG5Wl1aHXVEbnSajtqT2ooskwHfy81iwNqaGwVy+ZSLIZpqC91Hk9SyZ9
HBDuKWSzqEqXWf7nwbOTm0umQ9mk8+I41k+dyqc2fq9z/gySqKd32eC3aLa0/p3y
6bngvu1TT6jNhRdduwxgl/Y5cnQp/Zg9wYRKmAjViZtooaWj8p2o45AufGz1rplR
BdYVUOPofVVD9ShwxayWzuocFW/HbgYc7FHHgKUFgFBO5iC/A2s=
=UV0m
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2018-11-07' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v4.21, part 1:
UAPI Changes:
- Add syncobj timeline support to drm.
Cross-subsystem Changes:
- Remove shared fence staging in dma-buf's fence object, and allow
reserving more than 1 fence and add more paranoia when debugging.
- Constify infoframe functions in video/hdmi.
Core Changes:
- Add vkms todo, and a lot of assorted doc fixes.
- Drop transitional helpers and convert drivers to use drm_atomic_helper_shutdown().
- Move atomic state helper functions to drm_atomic_state_helper.[ch]
- Refactor drm selftests, and add new tests.
- DP MST atomic state cleanups.
- Drop EXPORT_SYMBOL from drm leases.
- Lease cleanups and fixes.
- Create render node for vgem.
Driver Changes:
- Fix build failure in imx without fbdev emulation.
- Add rotation quirk for GPD win2 panel.
- Add support for various CDTech panels, Banana Pi Panel, DLC1010GIG,
Olimex LCD-O-LinuXino, Samsung S6D16D0, Truly NT35597 WQXGA,
Himax HX8357D, simulated RTSM AEMv8.
- Add dw_hdmi support to rockchip driver.
- Fix YUV support in vc4.
- Fix resource id handling in virtio.
- Make rockchip use dw-mipi-dsi bridge driver, and add dual dsi support.
- Advertise that tinydrm only supports DRM_FORMAT_MOD_LINEAR.
- Convert many drivers to use atomic helpers, and drm_fbdev_generic_setup().
- Add Mali linear tiled formats, and enable them in the Mali-DP driver.
- Add support for H6 DE3 mixer 0, DW HDMI, HDMI PHY and TCON TOP.
- Assorted driver cleanups and fixes.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/be7ebd91-edd9-8fa4-4286-1c57e3165113@linux.intel.com
If we have released no firmware yet for a platform, stop scaring the
consumer and merely note its expected absence.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Petri Latvala <petri.latvala@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181009111259.20807-1-chris@chris-wilson.co.uk
I have a Thinkpad X220 Tablet in my hands that is losing vblank
interrupts whenever LP3 watermarks are used.
If I nudge the latency value written to the WM3 register just
by one in either direction the problem disappears. That to me
suggests that the punit will not enter the corrsponding
powersave mode (MPLL shutdown IIRC) unless the latency value
in the register matches exactly what we read from SSKPD. Ie.
it's not really a latency value but rather just a cookie
by which the punit can identify the desired power saving state.
On HSW/BDW this was changed such that we actually just write
the WM level number into those bits, which makes much more
sense given the observed behaviour.
We could try to handle this by disallowing LP3 watermarks
only when vblank interrupts are enabled but we'd first have
to prove that only vblank interrupts are affected, which
seems unlikely. Also we can't grab the wm mutex from the
vblank enable/disable hooks because those are called with
various spinlocks held. Thus we'd have to redesigne the
watermark locking. So to play it safe and keep the code
simple we simply disable LP3 watermarks on all SNB machines.
To do that we simply zero out the latency values for
watermark level 3, and we adjust the watermark computation
to check for that. The behaviour now matches that of the
g4x/vlv/skl wm code in the presence of a zeroed latency
value.
v2: s/USHRT_MAX/U32_MAX/ for consistency with the types (Chris)
Cc: stable@vger.kernel.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101269
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103713
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114173440.6730-1-ville.syrjala@linux.intel.com
Bspec 21257 says "DDIA PHY is the comp master, so it must
not be un-initialized if other combo PHYs are in use". Here
we are shutting down all phys, so it's not strictly required.
However let's be consistent on deinitializing things in the
reversed order we initialized them.
v2: simplify protection for enum port being unsigned in future
v3: spell out reverse rather than rev
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114011509.3667-2-lucas.demarchi@intel.com
These are the only places that assume ports A and B are the ones with
combo phy. Let's use intel_port_is_combophy() there to make sure
it checks for combo phy ports the same way everywhere.
v2: define for_each_combo_port() helper to check the ports
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114011509.3667-1-lucas.demarchi@intel.com
reorder structure of 297, 594 N values to group Audio Sample Frequencies
together to make updating from HDMI specification easier.
V2: Match patch 1/2 version
V3: Arrange by sample freq, then pixel clock.
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1541019295-20016-1-git-send-email-clinton.a.taylor@intel.com
To get the initial phase correct we need to account for the scale
factor as well. I forgot this initially and was mostly looking at
heavily upscaled content where the minor difference between -0.5
and the proper initial phase was not readily apparent.
And let's toss in a comment that tries to explain the formula
a little bit.
v2: The initial phase upper limit is 1.5, not 24.0!
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 0a59952b24 ("drm/i915: Configure SKL+ scaler initial phase correctly")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181029181820.21956-1-ville.syrjala@linux.intel.com
Tested-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Tested-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> #irc
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> #irc
(cherry picked from commit e7a278a329)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
While removing .palette_offsets, I removed the commas after
.trans_offsets in the macros, but failed to remove the line continuation
backslashes.
While at it, also remove another extra comma to be in line with the
other related macros.
Fixes: 74c1e82642 ("drm/i915: remove palette_offsets from device info in favor of _PICK()")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114112130.22264-1-jani.nikula@intel.com
Use intel_plane_destroy_state in intel_plane_free to free the state.
Also fix intel_plane_alloc() to use __drm_atomic_helper_plane_reset(),
to get sane defaults from the atomic core.
This is needed to get the correct alpha value and blend mode from the
core, and any new default values added from new properties.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: b208152556 ("drm/i915: Add plane alpha blending support, v2.")
[mlankhorst: Update commit description to mention alpha blend support]
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181113092804.13304-1-maarten.lankhorst@linux.intel.com
Even though PW#1 and the MISC_IO power wells are managed by the
DMC firmware (toggled dynamically if conditions allow it) from the
driver's POV they are always on if the display core is initialized
(always restored by DMC to the enabled state after exiting from DC5/6
for instance b/c of MMIO access). Accordingly we can just mark them as
always-on and remove the special casing for them during state
verification (thus enabling verification for these power wells too).
Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181109145822.15446-3-imre.deak@intel.com
We can just use a proper true/false initializer even for bitfields,
which is more descriptive.
Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181109145822.15446-2-imre.deak@intel.com
A DMC bug on GEN9 big core machines fails to restore the driver's
request bits for the PW1 and MISC_IO power wells after a DC5/6
entry->exit sequence. As a consequence the driver's subsequent check for
the enabled status of these power wells will fail, as the check
considers the power wells being enabled only if both the status and
request bits are set. To work around this borrow the request bits from
BIOS's own request register in which DMC forces on the request bits when
exiting from DC5/6.
This fixes a problem reported by Ramalingam, where HDCP init failed,
since PW1 reported itself as being disabled, while in reality it was
enabled.
Reported-by: Ramalingam C <ramalingam.c@intel.com>
Cc: Ramalingam C <ramalingam.c@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181109145822.15446-1-imre.deak@intel.com
Register DBUF_CTL_S2 is read and it's value is not used. As
there is no explanation why we should prime the hardware with
read, remove it as spurious.
Fixes: aa9664ffe8 ("drm/i915/icl: Enable 2nd DBuf slice only when needed")
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181109140924.2663-1-mika.kuoppala@linux.intel.com
(cherry picked from commit 8577c319b6)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
This got duplicated on introducing icl workarounds.
Fix by using the older definition and moving the wa bit
definition there. No functional changes.
v3: avoid fixes tag, whitespace (Chris)
References: 908ae05173 ("drm/i915/icl: WaDisCtxReload")
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20181109145333.10570-1-mika.kuoppala@linux.intel.com
Register DBUF_CTL_S2 is read and it's value is not used. As
there is no explanation why we should prime the hardware with
read, remove it as spurious.
Fixes: aa9664ffe8 ("drm/i915/icl: Enable 2nd DBuf slice only when needed")
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181109140924.2663-1-mika.kuoppala@linux.intel.com
I think I'm probably the one who argued in favor of having separate
implementations for both PCHs, but the calculations are actually the
same, the clocks are the same and the only difference is that on ICP
we write the numerator to the register.
I have previously suggested to kill cnp_rawclk() and keep the
icp_rawclk() style, but Ville gave some good arguments that what's in
this patch may be the better choice.
v2: Switch numerator to 1 from 1000 and adjust calculations
accordingly (Ville).
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181112232313.26373-3-paulo.r.zanoni@intel.com
Although CNP names this field "Counter Fraction", what we write to the
register is really the denominator for the fractional part of the
divider, not the fractional part (and the field description even says
that). The ICP spec renamed the field to "Counter Fraction
Denominator", which makes a lot more sense. Use the more complete ICL
naming because we will merge the CNP and ICP functions into a single
one, which will introduce the concept of the numerator. That will make
a lot more sense when you read the "num/frac = den" calculation.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181112232313.26373-2-paulo.r.zanoni@intel.com
BSpec was updated and now there's no more "subtract 1" to the
Microsecond Counter Divider field.
It seems this should help fixing some GMBUS issues. I'm not aware of
any specific open bug that could be solved by this patch.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181112232313.26373-1-paulo.r.zanoni@intel.com
VBT appears to have two (or possibly three) ways to indicate the panel
rotation. The first is in the MIPI config block, but that apparenly
usually (maybe always?) indicates 0 degrees despite the actual panel
orientation. The second way to indicate this is in the general features
block, which can just indicate whether 180 degress rotation is used.
The third might be a separate rotation data block, but that is not
at all documented so who knows what it may contain.
Let's try the first two. We first try the DSI specicic VBT
information, and it it doesn't look trustworthy (ie. indicates
0 degrees) we fall back to the 180 degree thing. Just to avoid too
many changes in one go we shall also keep the hardware readout path
for now.
If this works for more than just my VLV FFRD the question becomes
how many of the panel orientation quirks are now redundant?
v2: Move the code into intel_dsi.c (Jani)
Cc: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181022142015.4026-1-ville.syrjala@linux.intel.com
Tested-by: Hans de Goede <hdegoede@redhat.com>
Let's make sure the DSI port is actually on before we go
poking at the plane register to determine which way
it's rotated. Otherwise we could be looking at a plane
that is feeding a HDMI port for instance.
And in order to read the plane register we need the power
well to be on. Make sure that is indeed the case. We'll
also make sure the plane is actually enabled before we
trust the rotation bit to tell us the truth.
v2: s/intel_dsi/vlv_dsi/
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181022141953.3889-1-ville.syrjala@linux.intel.com
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> #irc
No point in cluttering the common codepaths with the
skip_intermediate_wm handling. Just move it into
ilk_compute_intermediate_wm() as those are the only
platforms using this.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181108151013.24064-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> #irc
To get the initial phase correct we need to account for the scale
factor as well. I forgot this initially and was mostly looking at
heavily upscaled content where the minor difference between -0.5
and the proper initial phase was not readily apparent.
And let's toss in a comment that tries to explain the formula
a little bit.
v2: The initial phase upper limit is 1.5, not 24.0!
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 0a59952b24 ("drm/i915: Configure SKL+ scaler initial phase correctly")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181029181820.21956-1-ville.syrjala@linux.intel.com
Tested-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Tested-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> #irc
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> #irc
Reduce the clutter in the sprite update functions by writing
both TILEOFF and LINOFF registers unconditionally. We already
did this for primary planes so might as well do it for the
sprites too.
There is no harm in writing both registers. Which one gets
used depends on the tilimg mode selected in the plane control
registers.
It might even make sense to clear the register that won't
get used. That could make register dumps a little easier to
parse. But I'm not sure it's worth the extra hassle.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181108150955.23948-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> #irc
We no longer change LSPCON into PCON mode if it boots up in
LS mode. This was broken by some code shuffling in
commit 96e35598ce ("drm/i915: Check LSPCON vendor OUI").
I actually can't see a reason why that code shuffling had
to be done. The commit msg notes it but doesn't justify it
in any way. But I guess we'll keep the code in its current
place anyway and just make the "switch to PCON mode" part
effective once again.
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Tested-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Fixes: 96e35598ce ("drm/i915: Check LSPCON vendor OUI")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107171821.27862-1-ville.syrjala@linux.intel.com
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
drm-next is forwarded to v4.20-rc1, and we need this to make
a patch series apply.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
We need to include the revert of commit 783195ec1c ("drm/syncobj:
disable the timeline UAPI for now v2") along with undoing the change to
drm/i915.
Fixes: 131280a162 ("drm: Revert syncobj timeline changes.")
Cc: Christian König <christian.koenig@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chunming Zhou <david1.zhou@amd.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20181112152130.12275-1-chris@chris-wilson.co.uk
In my haste to remove irq_port[] I accidentally changed the
way we deal with hpd pins that are shared by multiple encoders
(DP and HDMI for pre-DDI platforms). Previously we would only
handle such pins via ->hpd_pulse(), but now we queue up the
hotplug work for the HDMI encoder directly. Worse yet, we now
count each hpd twice and this increment the hpd storm count
twice as fast. This can lead to spurious storms being detected.
Go back to the old way of doing things, ie. delegate to
->hpd_pulse() for any pin which has an encoder with that hook
implemented. I don't really like the idea of adding irq_port[]
back so let's loop through the encoders first to check if we
have an encoder with ->hpd_pulse() for the pin, and then go
through all the pins and decided on the correct course of action
based on the earlier findings.
I have occasionally toyed with the idea of unifying the pre-DDI
HDMI and DP encoders into a single encoder as well. Besides the
hotplug processing it would have the other benefit of preventing
userspace from trying to enable both encoders at the same time.
That is simply illegal as they share the same clock/data pins.
We have some testcases that will attempt that and thus fail on
many older machines. But for now let's stick to fixing just the
hotplug code.
Cc: stable@vger.kernel.org # 4.19+
Cc: Lyude Paul <lyude@redhat.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Fixes: b6ca3eee18 ("drm/i915: Nuke dev_priv->irq_port[]")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181108200424.28371-1-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
(cherry picked from commit 5a3aeca97a)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
To enable DC5/6 power well 2 has to be disabled as for previous
platforms, so fix things up.
Bspec: 4234
Fixes: 67ca07e7ac ("drm/i915/icl: Add power well support")
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181102182200.17219-1-imre.deak@intel.com
(cherry picked from commit a33e1ece77)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
This hasn't caused any issues yet that I'm aware of, but as Ville
Syrjälä pointed out - we need to make sure that
intel_connector->mst_port is set before initializing MST connectors,
since in theory we could potentially check intel_connector->mst_port in
i915_hpd_poll_init_work() after registering the connector but before
having written it's value.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: stable@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20181106213017.14563-2-lyude@redhat.com
(cherry picked from commit 66a5ab1034)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Exercising the gpu reloc path strenuously revealed an issue where the
updated relocations (from MI_STORE_DWORD_IMM) were not being observed
upon execution. After some experiments with adding pipecontrols (a lot
of pipecontrols (32) as gen4/5 do not have a bit to wait on earlier pipe
controls or even the current on), it was discovered that we merely
needed to delay the EMIT_INVALIDATE by several flushes. It is important
to note that it is the EMIT_INVALIDATE as opposed to the EMIT_FLUSH that
needs the delay as opposed to what one might first expect -- that the
delay is required for the TLB invalidation to take effect (one presumes
to purge any CS buffers) as opposed to a delay after flushing to ensure
the writes have landed before triggering invalidation.
Testcase: igt/gem_tiled_fence_blits
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181105094305.5767-1-chris@chris-wilson.co.uk
(cherry picked from commit 55f99bf2a9)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Pass on the errno all the way from connected_sink_max_bpp(),
and make the base_bpp handling in intel_modeset_pipe_config()
a bit less ugly. We'll also rename connected_sink_max_bpp()
to not give the impression that it return the bpp value,
and we'll pimp up the debug message within to include the
connector name/id.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107213522.17590-3-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
ironlake_check_fdi_lanes() may try to grab some extra crtc locks.
If that fails we need to propagate the -EDEADLK all the way up,
and we shouldn't dump out the crtc state or other debug messages
either since it wasn't the crtc state that caused the failure.
Just hit this on my IVB:
[drm:intel_atomic_check [i915]] checking fdi config on pipe C, lanes 3
[drm:intel_atomic_check [i915]] only 2 lanes on pipe C: required 3 lanes
[drm:intel_atomic_check [i915]] fdi link bw constraint, reducing pipe bpp to 18
[drm:intel_atomic_check [i915]] checking fdi config on pipe C, lanes 2
[drm:intel_atomic_check [i915]] CRTC bw constrained, retrying
[drm:intel_dp_compute_config [i915]] DP link computation with max lane count 4 max rate 270000 max bpp 18 pixel clock 185580KHz
[drm:intel_dp_compute_config [i915]] DP lane count 4 clock 162000 bpp 18
[drm:intel_dp_compute_config [i915]] DP link rate required 417555 available 648000
[drm:intel_atomic_check [i915]] checking fdi config on pipe C, lanes 2
WARNING: CPU: 4 PID: 25115 at ../drivers/gpu/drm/drm_modeset_lock.c:241 drm_modeset_lock+0xbc/0xd0 [drm]
...
WARNING: CPU: 4 PID: 25115 at ../drivers/gpu/drm/drm_modeset_lock.c:223 drm_modeset_drop_locks+0x4a/0x50 [drm]
The warnings are from 'WARN_ON(ctx->contended)'.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107213522.17590-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
We dump the info as an array of u8, so we want to know the length
in number of bytes. Current code is still safe because the
variable we use BITS_PER_TYPE on is a u8.
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181109004013.34394-1-daniele.ceraolospurio@intel.com
We have a subslice mask per slice, not per subslice.
MAX_SUBSLICES > MAX_SLICES, so the wrong size didn't cause any issue
apart from using extra memory.
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181106182918.5748-1-daniele.ceraolospurio@intel.com
In the past we had hooks to configure HW for VLV/CHV too, in the drop
of VLV/CHV support the intel_psr_disable_source() code was not moved
to the caller, so doing it here.
Suggested-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181106190843.18009-4-jose.souza@intel.com
All other interruptions gen11 interruptions are reset in
gen11_irq_reset() also it is done for other gens that supports PSR.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181106190843.18009-3-jose.souza@intel.com
It should always wait for idle state when disabling PSR because PSR
could be inactive due a call to intel_psr_exit() and while PSR is
still being disabled asynchronously userspace could change the
modeset causing a call to psr_disable() that will not wait for PSR
idle and then PSR will be enabled again while PSR is still not idle.
v2: rebased on top of the patch reusing psr_exit()
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181106190843.18009-2-jose.souza@intel.com
Both functions have the same code to disable PSR, so let's reuse that
code instead of duplicate.
Suggested-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181106190843.18009-1-jose.souza@intel.com
Make skl_ddb_allocation_overlaps() useful for other callers
besides skl_update_crtcs(). We'll need it to do plane updates
as well.
And while we're here we can reduce the stack utilization a
bit by noting that each struct skl_ddb_entry is 4 bytes whereas
a pointer to one is 8 bytes (on 64bit). So we'll switch to an
array of structs from the array of pointers we used before.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101150605.18235-9-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Due to the constant alpha we're going to have to program two of
the the tree keying registers anyway, so might as well always
program all three.
And parametrize the plane constant alpha define while at it.
v2: Rebase due to input CSC
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107184138.31359-1-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
MST is only supported in DDI ports that have this hook, so the null
check can be dropped.
Suggested-by: Imre Deak <imre.deak@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107235449.32264-3-jose.souza@intel.com
MST ports did not had the post_pll_disable() hook causing the
references get in pre_pll_enable() never being released causing
DDI and AUX CH being enabled all the times.
v2: renamed intel_mst_post_pll_disable_dp() parameters
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107235449.32264-2-jose.souza@intel.com
intel_dp_detect() caches the aux_domain in the beginning of the
function as it is used twice, so lets also use it as the aux_domain
don't change in runtime.
v3: returning intel_dp_retrain_link() error insted of
connector_status_disconnected
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107235449.32264-1-jose.souza@intel.com
IBX has a documented workaround which states that when we disable the
port we must change its transcoder select to A, otherwise it will
prevent the other port (DP vs. HDMI/SDVO) from using transcoder A.
We implement the workaround during encoder disable, but looks like
some BIOSen leave transcoder B selected even when the port wasn't
actually enabled by the BIOS. That will trip up our asserts
that attempt to make sure we never forget this w/a.
Sanitize the transcoder select to A for all disabled PCH
DP/HDMI/SDVO ports. We assume that the port was never enabled
by the BIOS on transcoder B, because if it had we'd actually have
to toggle the port on and back off to properly switch it back to
transcoder A. That would cause some display flicker if transcoder A
is already enabled on some other port, so it's better not to do it
unless absolutely necessary. Since we have no indication that the
transcoder select is misbehaving on the affected machines we can
assume the port was never actually enabled by the BIOS.
This cures warning like this during driver load:
IBX PCH DP C still using transcoder B
WARNING: CPU: 2 PID: 172 at drivers/gpu/drm/i915/intel_display.c:1279 assert_pch_dp_disabled+0x9e/0xb0 [i915]
v2: Add comments to remind the reader that SDVOB==HDMIB (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181108143635.9556-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
In my haste to remove irq_port[] I accidentally changed the
way we deal with hpd pins that are shared by multiple encoders
(DP and HDMI for pre-DDI platforms). Previously we would only
handle such pins via ->hpd_pulse(), but now we queue up the
hotplug work for the HDMI encoder directly. Worse yet, we now
count each hpd twice and this increment the hpd storm count
twice as fast. This can lead to spurious storms being detected.
Go back to the old way of doing things, ie. delegate to
->hpd_pulse() for any pin which has an encoder with that hook
implemented. I don't really like the idea of adding irq_port[]
back so let's loop through the encoders first to check if we
have an encoder with ->hpd_pulse() for the pin, and then go
through all the pins and decided on the correct course of action
based on the earlier findings.
I have occasionally toyed with the idea of unifying the pre-DDI
HDMI and DP encoders into a single encoder as well. Besides the
hotplug processing it would have the other benefit of preventing
userspace from trying to enable both encoders at the same time.
That is simply illegal as they share the same clock/data pins.
We have some testcases that will attempt that and thus fail on
many older machines. But for now let's stick to fixing just the
hotplug code.
Cc: stable@vger.kernel.org # 4.19+
Cc: Lyude Paul <lyude@redhat.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Fixes: b6ca3eee18 ("drm/i915: Nuke dev_priv->irq_port[]")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181108200424.28371-1-ville.syrjala@linux.intel.com
Reviewed-by: Lyude Paul <lyude@redhat.com>
We shouldn't consider an encoder inactive if it doesn't have a CRTC
linked, but has virtual MST encoders with a crtc linked. Fix this.
Also we should not sanitize the mapping for MST encoders, as it's always
their primary encoder (which could be even in SST mode) whose active
state determines if we need the clock being enabled for the
corresponding physical port. Fix this too.
This fixes at least an existing breakage where we incorrectly disabled
the clock for an active DP encoder when sanitizing its MST virtual
encoders. Not sure if there are BIOSes that enable an output in MST
mode, but our HW readout is mostly missing for it anyway, so just warn
for that case.
Fixes: 70332ac539 ("drm/i915/icl+: Sanitize port to PLL mapping")
Cc: Antonio Argenziano <antonio.argenziano@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reported-by: Antonio Argenziano <antonio.argenziano@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Tested-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107200836.10191-2-imre.deak@intel.com
Check for reserved register field values and conflicting
transcoder->port mappings (both MST and non-MST mappings or multiple SST
mappings).
This is also needed for the next patch to determine if a port is in MST
mode during sanitization after HW readout.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Antonio Argenziano <antonio.argenziano@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107200836.10191-1-imre.deak@intel.com
While our little rcu worker might be able to be replaced now by the
dedicated rcu_work, in the meantime we should mark up the rcu_head for
correct debugobjects tracking.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181108092101.27598-2-chris@chris-wilson.co.uk
All other overlay functions(almost all other functions in i915)
follow intel_overlay_verb, so renaming overlay ones that do not match
that.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181108001647.11276-4-jose.souza@intel.com
IPC is a display feature, so i915_load_modeset_init() is the right
place to initialize it.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181108001647.11276-3-jose.souza@intel.com
Although FBC helps save power it do not belongs to power management
also the cleanup was placed in i915_driver_unload() also not a good
place. intel_modeset_init()/intel_modeset_cleanup() are better places
also this will help make easy disable features that depends in
display being enabled in driver.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181108001647.11276-2-jose.souza@intel.com
i915_load_modeset_init() is a more suitable place than
i915_driver_load() as vblank is part of modeset.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181108001647.11276-1-jose.souza@intel.com
This reduces the size of struct skl_wm_level from 6 to 4, which
reduces the size of struct skl_plane_wm from 104 to 70, which reduces
the size of struct skl_pipe_wm from 524 to 356. A reduction of 168
padding bytes per pipe. This will increase even more the next time we
bump I915_MAX_PLANES.
v2: Paste the pahole output provided by Lucas:
$ pahole -s -C skl_wm_level drivers/gpu/drm/i915/i915.o
struct skl_wm_level {
bool plane_en; /* 0 1 */
/* XXX 1 byte hole, try to pack */
uint16_t plane_res_b; /* 2 2 */
uint8_t plane_res_l; /* 4 1 */
/* size: 6, cachelines: 1, members: 3 */
/* sum members: 4, holes: 1, sum holes: 1 */
/* padding: 1 */
/* last cacheline: 6 bytes */
};
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181016220133.26991-3-paulo.r.zanoni@intel.com
We have multiple instances of VCS but only remember to invalidate the
BSD caches on the first, ignoring the stale caches of any other engine.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181108140039.12254-1-chris@chris-wilson.co.uk
On ICL DMC/PCODE retains the HW context only for port A across DC
transitions, for the other port B combo PHY, it doesn't. So we need to
do this manually after exiting from DC6. Do the reinit even after
exiting from DC5, it won't hurt since we only reinit the PHY in case
it's needed (in case it was disabled to begin with).
As can be guessed from the bugzilla report leaving the PHY uninited will
lead to a later timeout during the port B specific AUX and DDI_IO power
well enabling.
v2:
- Apply the fix on all GEN>=11 platforms. (Rodrigo)
Bspec: 21257
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108070
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181106160621.23057-6-imre.deak@intel.com
Bspec says we should skip the initialization of combo PHYs that are
already initialized. We'll need to reinit the PHYs more frequently
when exiting from DC6 (after the next patch), so let's make sure the
uninit sequence complies with the spec. For safety skip the init only if
all the PHY register fields have their expected values.
v2:
- Print 'Port X' as we do elsewhere instead of 'Port-X'. (Jose)
Bspec: 21257
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181106160621.23057-5-imre.deak@intel.com
Verify on CNL, ICL that the combo PHY HW state stayed intact after PHY
initialization.
v2:
- Print 'Port X' as we do elsewhere instead of 'Port-X'. (Jose)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181106160621.23057-4-imre.deak@intel.com
Similarly to the GEN9_LP DPIO PHY code keep the CNL+ combo PHY code in a
separate file.
No functional change.
v2:
- Use SPDX license tag instead of boilerplate. (Rodrigo)
v3:
- Use MIT instead of GPL-2.0 license. (Ville)
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181106160621.23057-3-imre.deak@intel.com
BSpec says to clear the comp init HW flag too during combo PHY uninit,
so do that. The lack of this could badly interact with the PHY reinit
after a DC6/9 transition at least, where (after a follow-up patch fixing
the init code) we'd skip the initialization incorrectly due to this flag
being set.
BSpec: 21257
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181106160621.23057-2-imre.deak@intel.com
To enable DC5/6 power well 2 has to be disabled as for previous
platforms, so fix things up.
Bspec: 4234
Fixes: 67ca07e7ac ("drm/i915/icl: Add power well support")
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181102182200.17219-1-imre.deak@intel.com
Unfortunately, it seems that the HPD IRQ storm problem from the early
days of Intel GPUs was never entirely solved, only mostly. Within the
last couple of days, I got a bug report from one of our customers who
had been having issues with their machine suddenly booting up very
slowly after having updated. The amount of time it took to boot went
from around 30 seconds, to over 6 minutes consistently.
After some investigation, I discovered that i915 was reporting massive
amounts of short HPD IRQ spam on this system from the DisplayPort port,
despite there not being anything actually connected. The symptoms would
start with one "long" HPD IRQ being detected at boot:
[ 1.891398] [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00440000, dig 0x00440000, pins 0x000000a0
[ 1.891436] [drm:intel_hpd_irq_handler [i915]] digital hpd port B - long
[ 1.891472] [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 5 - cnt: 0
[ 1.891508] [drm:intel_hpd_irq_handler [i915]] digital hpd port D - long
[ 1.891544] [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 7 - cnt: 0
[ 1.891592] [drm:intel_dp_hpd_pulse [i915]] got hpd irq on port B - long
[ 1.891628] [drm:intel_dp_hpd_pulse [i915]] got hpd irq on port D - long
…
followed by constant short IRQs afterwards:
[ 1.895091] [drm:intel_encoder_hotplug [i915]] [CONNECTOR:66:DP-1] status updated from unknown to disconnected
[ 1.895129] [drm:i915_hotplug_work_func [i915]] Connector DP-3 (pin 7) received hotplug event.
[ 1.895165] [drm:intel_dp_detect [i915]] [CONNECTOR:72:DP-3]
[ 1.895275] [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00200000, dig 0x00200000, pins 0x00000080
[ 1.895312] [drm:intel_hpd_irq_handler [i915]] digital hpd port D - short
[ 1.895762] [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00200000, dig 0x00200000, pins 0x00000080
[ 1.895799] [drm:intel_hpd_irq_handler [i915]] digital hpd port D - short
[ 1.896239] [drm:intel_dp_aux_xfer [i915]] dp_aux_ch timeout status 0x71450085
[ 1.896293] [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00200000, dig 0x00200000, pins 0x00000080
[ 1.896330] [drm:intel_hpd_irq_handler [i915]] digital hpd port D - short
[ 1.896781] [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00200000, dig 0x00200000, pins 0x00000080
[ 1.896817] [drm:intel_hpd_irq_handler [i915]] digital hpd port D - short
[ 1.897275] [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00200000, dig 0x00200000, pins 0x00000080
The customer's system in question has a GM45 GPU, which is apparently
well known for hotplugging storms.
So, workaround this impressively broken hardware by changing the default
HPD storm threshold from 5 to 50. Then, make long IRQs count for 10, and
short IRQs count for 1. This makes it so that 5 long IRQs will trigger
an HPD storm, and on systems with short HPD storm detection 50 short
IRQs will trigger an HPD storm. 50 short IRQs amounts to 100ms of
constant pulsing, which seems like a good middleground between being too
sensitive and not being sensitive enough (which would cause visible
stutters in userspace every time a storm occurs).
And just to be extra safe: we don't enable this by default on systems
with MST support. There's too high of a chance of MST support triggering
storm detection, and systems that are new enough to support MST are a
lot less likely to have issues with IRQ storms anyway.
As a note: this patch was tested using a ThinkPad T450s and a Chamelium
to simulate the short IRQ storms.
Changes since v1:
- Don't use two separate thresholds, just make long IRQs count for 10
each and short IRQs count for 1. This simplifies the code a bit
- Ville Syrjälä
Changes since v2:
- Document @long_hpd in intel_hpd_irq_storm_detect, no functional
changes
Changes since v4:
- Remove !! in long_hpd assignment - Ville Syrjälä
- queue_hp = true - Ville Syrjälä
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181106213017.14563-6-lyude@redhat.com
This is rather confusing to look at as-is:
dev_priv->display.hpd_irq_setup(dev_priv); in intel_hpd_irq_handler()
handles disabling the actual HPD IRQ, while
intel_hpd_irq_storm_disable() handles moving the HPD pin state over from
MARK_DISABLED to DISABLED along with enabling polling for it.
Changes since v3:
- Rename i915_hpd_irq_storm_disable() to
i915_hpd_irq_storm_switch_to_polling() - Rodrigo Vivi
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181106213017.14563-5-lyude@redhat.com
Currently in intel_hpd_irq_storm_detect() when we detect that the last
recorded hotplug wasn't within the period defined by
HPD_STORM_DETECT_DELAY, we make the mistake of resetting the HPD count
to 0 without incrementing it. This results in us only enabling storm
detection when we go +2 above the threshold, e.g. an HPD threshold of 5
would not trigger a storm until we reach a total of 7 hotplugs.
So: rework the code a bit so we reset the HPD count when
HPD_STORM_DETECT_DELAY has passed, then increment the count afterwards.
Also, clean things up a bit to make it easier to undertand.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181106213017.14563-4-lyude@redhat.com
This hasn't caused any issues yet that I'm aware of, but as Ville
Syrjälä pointed out - we need to make sure that
intel_connector->mst_port is set before initializing MST connectors,
since in theory we could potentially check intel_connector->mst_port in
i915_hpd_poll_init_work() after registering the connector but before
having written it's value.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: stable@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20181106213017.14563-2-lyude@redhat.com
No need for the posting reads in the plane update/disable hooks.
If we need a posting read for something then a single one at the
very end would be sufficient. We have that anyway in the form
of eg. scanline/frame counter reads.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101150605.18235-2-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Exercising the gpu reloc path strenuously revealed an issue where the
updated relocations (from MI_STORE_DWORD_IMM) were not being observed
upon execution. After some experiments with adding pipecontrols (a lot
of pipecontrols (32) as gen4/5 do not have a bit to wait on earlier pipe
controls or even the current on), it was discovered that we merely
needed to delay the EMIT_INVALIDATE by several flushes. It is important
to note that it is the EMIT_INVALIDATE as opposed to the EMIT_FLUSH that
needs the delay as opposed to what one might first expect -- that the
delay is required for the TLB invalidation to take effect (one presumes
to purge any CS buffers) as opposed to a delay after flushing to ensure
the writes have landed before triggering invalidation.
Testcase: igt/gem_tiled_fence_blits
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181105094305.5767-1-chris@chris-wilson.co.uk
The i915 driver uses shmemfs to allocate backing storage for gem
objects. These shmemfs pages can be pinned (increased ref count) by
shmem_read_mapping_page_gfp(). When a lot of pages are pinned, vmscan
wastes a lot of time scanning these pinned pages. In some extreme case,
all pages in the inactive anon lru are pinned, and only the inactive
anon lru is scanned due to inactive_ratio, the system cannot swap and
invokes the oom-killer. Mark these pinned pages as unevictable to speed
up vmscan.
Export pagevec API check_move_unevictable_pages().
This patch was inspired by Chris Wilson's change [1].
[1]: https://patchwork.kernel.org/patch/9768741/
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Kuo-Hsin Yang <vovoy@chromium.org>
Acked-by: Michal Hocko <mhocko@suse.com> # mm part
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Dave Hansen <dave.hansen@intel.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20181106132324.17390-1-chris@chris-wilson.co.uk
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
gvt-fixes-2018-11-07
- Fix invalidate of old ggtt entry (Hang)
- Fix partial ggtt entry update in any order (Hang)
- Fix one mask setting for chicken reg (Xinyun)
- Fix eDP warning in guest (Longhe)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
From: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107023137.GO25194@zhen-hp.sh.intel.com
We're no longer programming any watermarks when we're disabling
a pipe. That means ilk_wm_merge() & co. will keep considering
the any pipe that is getting disabled as still enabled. Thus we
either get no LP1+ watermakrs (ilk-ivb), or we get suboptimal
ones (hsw-bdw).
This seems to have been broken by commit b6b178a772 ("drm/i915:
Calculate ironlake intermediate watermarks correctly, v2."). Before
that we apparently had some difference between the intermediate
and optimal watermarks and so we would program the optiomal ones.
Now intermediate and optimal are identical for disabled pipes
and so we don't program either.
Fix this by programming the intermediate watermarks even for
disabled pipes. We were already doing that for skl+. We'll
leave out gmch platforms for now since those do the merging
in a different manner and should work as is. We'll want to
unify this eventually, but play it safe for now and just put
in a FIXME.
Cc: stable@vger.kernel.org
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: b6b178a772 ("drm/i915: Calculate ironlake intermediate watermarks correctly, v2.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181025130536.29024-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> #irc
(cherry picked from commit a748faea3b)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
We deinit the lpe audio device before we call
drm_atomic_helper_shutdown(), which means the platform device
may already be gone when it comes time to shut down the crtc.
As we don't know when the last reference to the platform
device gets dropped by the audio driver we can't assume that
the device and its data are still around when turning off the
crtc. Mark the platform device as gone as soon as we do the
audio deinit.
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181105194604.6994-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit f45a7977d1)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Since the flags are being used to operate on a u64 variable, they too
need to be marked as such so that the inverses are full width (and not
zero extended on 32b kernels and bdw+).
Reported-by: Sergii Romantsov <sergii.romantsov@globallogic.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181102161232.17742-2-chris@chris-wilson.co.uk
(cherry picked from commit 83b466b1dc)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
This patch fixes the macros used for defining the DFLEXDPMLE
register bit fields. This accounts for changes in the spec.
Fixes: a2bc69a1a9 ("drm/i915/icl: Add register definition for DFLEXDPMLE")
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jose Roberto de Souza <jose.souza@intel.com>
Cc: <stable@vger.kernel.org> # v4.19+
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181023191248.26418-1-manasi.d.navare@intel.com
(cherry picked from commit b4335ec0a3)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Let's not leak obj->framebuffer_references when we decide that
the framebuffer domensions are not suitable for NV12.
Cc: stable@vger.kernel.org
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Vidya Srinivas <vidya.srinivas@intel.com>
Fixes: e44134f267 ("drm/i915: Add NV12 support to intel_framebuffer_init")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181029140031.11765-1-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
(cherry picked from commit 3b90946fcb)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
While checking the opportunity to add a display_gen
check to allow glk and cnl to be on same bucket I noticed
these FIXME cases here.
So I got the confirmation from HW architect that we actually
never needed this workaround.
"GLK supports 2 pixel per clock, so pixel clock can be up to 2 * cdclk."
So, this reverts commit 97f55ca5b6 ("drm/i915/glk: limit pixel
clock to 99% of cdclk workaround")
Fixes: 97f55ca5b6 ("drm/i915/glk: limit pixel clock to 99% of cdclk workaround")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Clinton Taylor <clinton.a.taylor@intel.com>
Cc: Arthur J Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181026005636.22274-1-rodrigo.vivi@intel.com
(cherry picked from commit 42882336e6)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Since we use a 64b virtual GTT irrespective of the system, we want to
ensure that the GTT computations remains 64b even on 32b systems,
including treatment of huge virtual pages.
No code generation changes on 64b:
Reported-by: Sergii Romantsov <sergii.romantsov@globallogic.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108282
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181025091823.20571-1-chris@chris-wilson.co.uk
(cherry picked from commit 9125963a94)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
The 16Gb DIMM w/a is not applicable to BXT or GLK. Limit it to
the appropriate platforms.
This was especially harsh on GLK since we don't even try to read
the DIMM information on that platforms, hence valid_dimm was
always false and thus we always tried to apply the w/a.
Furthermore the w/a pushed the level 0 latency above the
level 1 latency, which doesn't really make sense.
v2: Do the check when populating is_16gb_dimm (Mahesh)
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: 86b592876c ("drm/i915: Implement 16GB dimm wa for latency level-0")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181023182102.31549-1-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Mahesh Kumar <mahesh1.sh.kumar@gmail.com>
(cherry picked from commit 5d6f36b27d)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
We deinit the lpe audio device before we call
drm_atomic_helper_shutdown(), which means the platform device
may already be gone when it comes time to shut down the crtc.
As we don't know when the last reference to the platform
device gets dropped by the audio driver we can't assume that
the device and its data are still around when turning off the
crtc. Mark the platform device as gone as soon as we do the
audio deinit.
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181105194604.6994-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
As we may have to iterate a few thousand elements to acquire and release
the shmemfs backing storage for a GPU object, we need to break up the
long loop with cond_resched() to retain a modicum of low latency for
other processes.
Testcase: igt/benchmarks/gem_syslatency
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Kuo-Hsin Yang <vovoy@chromium.org>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181105170640.26905-1-chris@chris-wilson.co.uk
Plane input CSC needs to be enabled to convert frambuffers from
YUV to RGB. This is needed for bottom 3 planes on ICL, rest of
the planes have hardcoded conversion and taken care by the legacy
code.
This patch defines the co-efficient values for YUV to RGB conversion
in BT709 and BT601 formats. It programs the coefficients and enables
the plane input csc unit in hardware.
This has been verified and tested by Maarten and the change is working
as expecpted.
v2: Addressed Maarten's and Ville's review comments and added the
coefficients in a 2D array instead of independent Macros.
v3: Added individual coefficient matrix (9 values) instead of 6
register values as per Maarten's comment. Also addresed a shift
issue with B channel coefficient.
v4: Added support for Limited Range Color Handling
v5: Fixed Matt and Maarten's review comments.
v6: Added human readable matrix values for YUV to RGB Conversion along
with just the bspec register values, as per Matt's suggestion.
v7: Refactored the code, move csc coefficient programming function to
intel_sprite.c and made it static as per Ville's review comment.
v8: Addressed Ville's review comment. Called the coefficient programming
from within the skl_program_plane and used I915_WRITE_FW instead of
I915_WRITE.
v9: Fixed Ville's review comments.
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1541099420-12419-3-git-send-email-uma.shankar@intel.com
Defined the plane input csc coefficient registers and macros.
6 registers are used to program a total of 9 coefficients,
added macros to define each of them for all the planes
supporting the feature on pipes. On ICL, bottom 3 planes
have this capability.
v2: Segregated the register macro definition as separate patch
as per Maarten's suggestion.
v3: Removed a redundant 3rd Pipe register definition and
simplified the equally spaced register definition by adding an
offset as per Matt's comment.
v4: No Change
v5: Renamed the register Macro as per Matt's suggestion.
v6: No Change
v7: No Change
v8: No Change
v9: No Change
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1541099420-12419-2-git-send-email-uma.shankar@intel.com
We're no longer programming any watermarks when we're disabling
a pipe. That means ilk_wm_merge() & co. will keep considering
the any pipe that is getting disabled as still enabled. Thus we
either get no LP1+ watermakrs (ilk-ivb), or we get suboptimal
ones (hsw-bdw).
This seems to have been broken by commit b6b178a772 ("drm/i915:
Calculate ironlake intermediate watermarks correctly, v2."). Before
that we apparently had some difference between the intermediate
and optimal watermarks and so we would program the optiomal ones.
Now intermediate and optimal are identical for disabled pipes
and so we don't program either.
Fix this by programming the intermediate watermarks even for
disabled pipes. We were already doing that for skl+. We'll
leave out gmch platforms for now since those do the merging
in a different manner and should work as is. We'll want to
unify this eventually, but play it safe for now and just put
in a FIXME.
Cc: stable@vger.kernel.org
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: b6b178a772 ("drm/i915: Calculate ironlake intermediate watermarks correctly, v2.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181025130536.29024-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> #irc
On GEN9 LP (BXT/GLK) DC6 is not supported, so don't print the counter
on those platforms. So far we did this on GLK too.
While at it warn if we forgot to adjust the printout properly for a
new platform. (Rodrigo)
Testcase: igt/pm_dc/dc6-dpms
Cc: Jyoti Yadav <jyoti.r.yadav@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181031200220.11608-1-imre.deak@intel.com
The MG DP mode needs to be configured for Type C static/fixed/legacy
HDMI ports too, the same way as it's configured for Type C
static/fixed/legacy, fix this.
Bspec: 4232, 21735
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Tested-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181102192656.4472-3-imre.deak@intel.com
The MG PHY clock gating needs to be configured for Type C
static/fixed/legacy HDMI ports the same way it's configured for Type C
static/fixed/legacy and aternate mode DP ports, fix this.
Bspec: 4232, 21735
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Tested-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181102192656.4472-2-imre.deak@intel.com
Similar to DSC DPCD registers, let us cache
FEC_CAPABLE register to avoid using stale
values. With this we can avoid aux reads
everytime and instead read the cached values.
v2: Avoid using memset and array for a single
field. (Manasi,Jani)
v3: Print FEC CAPABILITY value. (Manasi)
Suggested-by: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181102041455.15818-1-anusha.srivatsa@intel.com
Since the flags are being used to operate on a u64 variable, they too
need to be marked as such so that the inverses are full width (and not
zero extended on 32b kernels and bdw+).
Reported-by: Sergii Romantsov <sergii.romantsov@globallogic.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181102161232.17742-2-chris@chris-wilson.co.uk
-----BEGIN PGP SIGNATURE-----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=5lmL
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2018-11-02' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Pretty much a normal fixes pull pre-rc1, mostly amdgpu fixes, one i915
link training regression fix, and a couple of minor panel/bridge fixes
and a panel quirk"
* tag 'drm-next-2018-11-02' of git://anongit.freedesktop.org/drm/drm: (37 commits)
drm/amdgpu: revert "enable gfxoff in non-sriov and stutter mode by default"
drm/amd/pp: Print warning if od_sclk/mclk out of range
drm/amd/pp: Fix pp_sclk/mclk_od not work on Vega10
drm/amd/pp: Fix pp_sclk/mclk_od not work on smu7
drm/amd/powerplay: no MGPU fan boost enablement on DPM disabled
drm/amdgpu: Fix skipping hangged job reset during gpu recover.
drm/amd/powerplay: revise Vega20 pptable version check
drm/amd/display: set backlight level limit to 1
drm/panel: simple: Innolux TV123WAM is actually P120ZDG-BF1
dt-bindings: drm/panel: simple: Innolux TV123WAM is actually P120ZDG-BF1
drm/bridge: ti-sn65dsi86: Remove the mystery delay
drm/panel: simple: Add "no-hpd" delay for Innolux TV123WAM
drm/panel: simple: Support panels with HPD where HPD isn't connected
dt-bindings: drm/panel: simple: Add no-hpd property
drm/edid: Add 6 bpc quirk for BOE panel.
drm/amdgpu: fix reporting of failed msg sent to SMU (v2)
drm/amdgpu: Fix compute ring 1.0.0 failure after reset
drm/amdgpu: fix VM leaf walking
drm/amdgpu: fix amdgpu_vm_fini
drm/amd/powerplay: commonize the API for retrieving current clocks
...
The registers DPCSSS,DPSP,DPMLE1 and DPPMS are all at an offset
from the base - which is the FLexi IO Adaptor. Lets follow the
offset calculation while accessing these registers.
v2:
- Follow spec for numbering - s/0/1(Lucas)
- s/FIA_1/FIA1_BASE (Anusha)
v3:
- Remove register offset defines. (Jani)
- Update comment. (Anusha)
v4: rebase. Remove comment.(Lucas)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101185557.29585-1-anusha.srivatsa@intel.com
Use the newly added "max bpc" connector property to limit pipe bpp.
V3: Use drm_connector_state to access the "max bpc" property
V4: Initialize the drm property, add suuport to DP(Ville)
V5: Use the property in the connector and fix CI failure(Ville)
V6: Use the core function to attach max_bpc property, remove the redundant
clamping of pipe bpp based on connector info
V7: Fix Checkpatch warnings
V9: Cleanup connected_sink_max_bpp and fix initial value in DP(Ville)
V12: Fix debug message(Ville)
V13: Remove the redundant check and simplify the check logic(Stan)
V14: Fix the check in connected_sink_max_bpp(Stan)
v15 (From Manasi): Add missing break (Stan)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Kishore Kadiyala <kishore.kadiyala@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181023014400.16055-1-manasi.d.navare@intel.com
Although there's nothing crucial missing, it's been a long time since
the last backmerge. Catch up with drm-next.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This patch fixes the naming of the registers:
s/PIPE_DSS_CTL/ICL_PIPE_DSS_CTL
And also fix the hex values to lower case, to match
rest of the definitions.
Manasi noticed this with the patch that was merged.
v2: fix "Fixes" tag.
Fixes: 8b1b558d69 ("drm/i915/icl: Add DSS_CTL Registers")
Suggested-by: Manasi Navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101214216.8958-1-anusha.srivatsa@intel.com
BIOS can leave the PLL to port mapping enabled, even if the
corresponding encoder is disabled. Disable the port mapping in this
case.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-9-imre.deak@intel.com
Most of the AUX_CH_CTL flags are concerned with DP AUX transfer
parameters. As opposed to this the flag specifying the thunderbolt vs.
non-thunderbolt mode of the port is not related to AUX transfers at all
(rather it's repurposed to enable either TBT or non-TBT PHY HW blocks).
The programming has to be done before enabling the corresponding AUX
power well, so make it part of the power well code.
v3:
- Use existing enable/disable helpers instead of opencoding. (Jose)
- Fix type of is_tc_tbt to remain a bitfield. (Lucas)
- Add comment describing the is_tc_tbt power well flag. (Lucas)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108548
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-8-imre.deak@intel.com
DDI/TypeC ports need the AUX power domain for main link functionality
even when they operate in HDMI static mode, so enable the power domain
for these ports too.
v4:
- Rebase on the upstream ICL pre_pll_enable change.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-7-imre.deak@intel.com
For DDI/TypeC ports the AUX power domain needs to be enabled before the
port's PLL is enabled, so move the enabling earlier accordingly.
v2:
- Preserve the pre_pll hook for GEN9_LP. (Ville)
v3:
- Add related BSpec entries to commit log. (Jose)
v4:
- Rebase on the upstream ICL pre_pll_enable change.
BSpec: 21750, 22243
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-6-imre.deak@intel.com
From ICL onwards the AUX power domain may change dynamically based on
whether a DDI/TypeC port is in thunderbolt or non-thunderbolt mode, so
use a helper function instead of a static field to get the current
domain.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-5-imre.deak@intel.com
From ICL onwards DDI/TypeC ports - even in HDMI static mode - need to know
which AUX CH belongs to them, so initialize aux_ch for those ports too.
For consistency do this for all HDMI ports, not only for DDI/TypeC ones.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-4-imre.deak@intel.com
From ICL onwards all DDI/TypeC ports - even working in HDMI mode - need
to know their corresponding AUX CH, so move the field to a common
struct.
No functional change.
v3:
- Add code comment about which ports aux_ch is used for. (Jose)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-3-imre.deak@intel.com
From ICL onwards all the DDI/TypeC ports - even working in HDMI mode -
need to know their corresponding AUX channel, so move the corresponding
helper to a common place.
No functional change.
v4:
- Fix 'no space is necessary after a cast' checkpatch warn.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-2-imre.deak@intel.com
Ville Syrjälä