When we have multiple interfaces receiving the same frame,
such as a multicast frame, one interface might have a sta
and the other not. In this case, link_sta would be set but
not cleared again.
Always set link_sta, so we keep an invariant that link_sta
and sta are either both set or both not set.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's at least one case in ieee80211_rx_for_interface()
where we might pass &((struct sta_info *)NULL)->sta to it
only to then do container_of(), and then checking the
result for NULL, but checking the result of container_of()
for NULL looks really odd.
Fix this by just passing the struct sta_info * instead.
Fixes: e66b7920aa ("wifi: mac80211: fix initialization of rx->link and rx->link_sta")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The ieee80211_accept_frame() function performs a number of early checks
to decide whether or not further processing needs to be done on a frame.
One of those checks is the ieee80211_is_robust_mgmt_frame() function.
It requires to peek into the frame payload, but because defragmentation
does not occur until later on in the receive path, this peek is invalid
for any fragment other than the first one. Also, in this scenario there
is no STA and so the fragmented frame will be dropped later on in the
process and will not reach the upper stack. This can happen with large
action frames at low rates, for example, we see issues with DPP on S1G.
This change will only check if the frame is robust if it's the first
fragment. Invalid fragmented packets will be discarded later after
defragmentation is completed.
Signed-off-by: Gilad Itzkovitch <gilad.itzkovitch@morsemicro.com>
Link: https://lore.kernel.org/r/20221124005336.1618411-1-gilad.itzkovitch@morsemicro.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
MLD address translation should be done only for individually addressed
frames. Otherwise, AAD calculation would be wrong and the decryption
would fail.
Fixes: e66b7920aa ("wifi: mac80211: fix initialization of rx->link and rx->link_sta")
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Link: https://lore.kernel.org/r/20230214101048.792414-1-andrei.otcheretianski@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Non-MLO station frames are dropped in Rx path due to the condition
check in ieee80211_rx_is_valid_sta_link_id(). In multi-link AP scenario,
non-MLO stations try to connect in any of the valid links in the ML AP,
where the station valid_links and link_id params are valid in the
ieee80211_sta object. But ieee80211_rx_is_valid_sta_link_id() always
return false for the non-MLO stations by the assumption taken is
valid_links and link_id are not valid in non-MLO stations object
(ieee80211_sta), this assumption is wrong. Due to this assumption,
non-MLO station frames are dropped which leads to failure in association.
Fix it by removing the condition check and allow the link validation
check for the non-MLO stations.
Fixes: e66b7920aa ("wifi: mac80211: fix initialization of rx->link and rx->link_sta")
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://lore.kernel.org/r/20230206160330.1613-1-quic_periyasa@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
At least ath10k and ath11k supported hardware (maybe more) does not implement
mesh A-MSDU aggregation in a standard compliant way.
802.11-2020 9.3.2.2.2 declares that the Mesh Control field is part of the
A-MSDU header (and little-endian).
As such, its length must not be included in the subframe length field.
Hardware affected by this bug treats the mesh control field as part of the
MSDU data and sets the length accordingly.
In order to avoid packet loss, keep track of which stations are affected
by this and take it into account when converting A-MSDU to 802.3 + mesh control
packets.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230213100855.34315-5-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current mac80211 mesh A-MSDU receive path fails to parse A-MSDU packets
on mesh interfaces, because it assumes that the Mesh Control field is always
directly after the 802.11 header.
802.11-2020 9.3.2.2.2 Figure 9-70 shows that the Mesh Control field is
actually part of the A-MSDU subframe header.
This makes more sense, since it allows packets for multiple different
destinations to be included in the same A-MSDU, as long as RA and TID are
still the same.
Another issue is the fact that the A-MSDU subframe length field was apparently
accidentally defined as little-endian in the standard.
In order to fix this, the mesh forwarding path needs happen at a different
point in the receive path.
ieee80211_data_to_8023_exthdr is changed to ignore the mesh control field
and leave it in after the ethernet header. This also affects the source/dest
MAC address fields, which now in the case of mesh point to the mesh SA/DA.
ieee80211_amsdu_to_8023s is changed to deal with the endian difference and
to add the Mesh Control length to the subframe length, since it's not covered
by the MSDU length field.
With these changes, the mac80211 will get the same packet structure for
converted regular data packets and unpacked A-MSDU subframes.
The mesh forwarding checks are now only performed after the A-MSDU decap.
For locally received packets, the Mesh Control header is stripped away.
For forwarded packets, a new 802.11 header gets added.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230213100855.34315-4-nbd@nbd.name
[fix fortify build error]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Now that all drivers use iTXQ, it does not make sense to check to drop
tx forwarding packets when the driver has stopped the queues.
fq_codel will take care of dropping packets when the queues fill up
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20230213100855.34315-3-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Somehow an extra 'e' slipped in there without anyone noticing,
drop that from ieeee80211_obss_color_collision_notify().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add minimal support for RX EHT rate reporting, not yet
adding (modifying) any radiotap headers, just statistics
for cfg80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When multiple interfaces are present in the local interface
list, new skb copy is taken before rx processing except for
the first interface. The address translation happens each
time only on the original skb since the hdr pointer is not
updated properly to the newly created skb.
As a result frames start to drop in userspace when address
based checks or search fails.
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Link: https://lore.kernel.org/r/20221208040050.25922-1-quic_srirrama@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_drop_unencrypted is called from ieee80211_rx_h_mesh_fwding and
ieee80211_frame_allowed.
Since ieee80211_rx_h_mesh_fwding can forward packets for other mesh nodes
and is called earlier, it needs to check the decryptions status and if the
packet is using the control protocol on its own, instead of deferring to
the later call from ieee80211_frame_allowed.
Because of that, ieee80211_drop_unencrypted has a mesh specific check
that skips over the mesh header in order to check the payload protocol.
This code is invalid when called from ieee80211_frame_allowed, since that
happens after the 802.11->802.3 conversion.
Fix this by moving the mesh specific check directly into
ieee80211_rx_h_mesh_fwding.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20221201135730.19723-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
First set of patches v6.2. mac80211 refactoring continues for Wi-Fi 7.
All mac80211 driver are now converted to use internal TX queues, this
might cause some regressions so we wanted to do this early in the
cycle.
Note: wireless tree was merged[1] to wireless-next to avoid some
conflicts with mac80211 patches between the trees. Unfortunately there
are still two smaller conflicts in net/mac80211/util.c which Stephen
also reported[2]. In the first conflict initialise scratch_len to
"params->scratch_len ?: 3 * params->len" (note number 3, not 2!) and
in the second conflict take the version which uses elems->scratch_pos.
Git diff output should like this:
--- a/net/mac80211/util.c
+++ b/net/mac80211/util.c
@@@ -1506,7 -1648,7 +1650,7 @@@ ieee802_11_parse_elems_full(struct ieee
const struct element *non_inherit = NULL;
u8 *nontransmitted_profile;
int nontransmitted_profile_len = 0;
- size_t scratch_len = params->len;
- size_t scratch_len = params->scratch_len ?: 2 * params->len;
++ size_t scratch_len = params->scratch_len ?: 3 * params->len;
elems = kzalloc(sizeof(*elems) + scratch_len, GFP_ATOMIC);
if (!elems)
[1] https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next.git/commit/?id=dfd2d876b3fda1790bc0239ba4c6967e25d16e91
[2] https://lore.kernel.org/all/20221020032340.5cf101c0@canb.auug.org.au/
Major changes:
mac80211
* preparation for Wi-Fi 7 Multi-Link Operation (MLO) continues
* add API to show the link STAs in debugfs
* all mac80211 drivers are now using mac80211 internal TX queues (iTXQs)
rtw89
* support 8852BE
rtl8xxxu
* support RTL8188FU
brmfmac
* support two station interfaces concurrently
bcma
* support SPROM rev 11
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmNb2KwRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZs6hggAqrmgHaiRbPYlLVE0hFVaGeVXslfpK9nj
ZGr3bwG5FpioxjAsI7NfwEwpq+FoxTUigG/SShw1Rr8lw43Nt7E57+5McK3qWdKC
5/WndfChPppjtJUpc6PN+UcmCuhcm4TAyMAojbTe5lJ9cJ4yyOWZChDwah3BVZQk
/tHK4qKq8gpppwgkiJ88VdTVoVv5anIvXHH3lAIteljxk0zkaEM7lIQhIFst/zpX
cu/cWvKz2Rh6vnYjkzl8BcrbW8e0/VwnzWggtWs4/kIuRVnHRrrGwlnsULShOscM
fmK+RI2CbJIMucttUOHOXjCg4wwppSit1rH4xOkcwlvrFa7AvDbdHg==
=Zils
-----END PGP SIGNATURE-----
Kalle Valo says:
====================
pull-request: wireless-next-2022-10-28
First set of patches v6.2. mac80211 refactoring continues for Wi-Fi 7.
All mac80211 driver are now converted to use internal TX queues, this
might cause some regressions so we wanted to do this early in the
cycle.
Note: wireless tree was merged[1] to wireless-next to avoid some
conflicts with mac80211 patches between the trees. Unfortunately there
are still two smaller conflicts in net/mac80211/util.c which Stephen
also reported[2]. In the first conflict initialise scratch_len to
"params->scratch_len ?: 3 * params->len" (note number 3, not 2!) and
in the second conflict take the version which uses elems->scratch_pos.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next.git/commit/?id=dfd2d876b3fda1790bc0239ba4c6967e25d16e91
[2] https://lore.kernel.org/all/20221020032340.5cf101c0@canb.auug.org.au/
mac80211
- preparation for Wi-Fi 7 Multi-Link Operation (MLO) continues
- add API to show the link STAs in debugfs
- all mac80211 drivers are now using mac80211 internal TX queues (iTXQs)
rtw89
- support 8852BE
rtl8xxxu
- support RTL8188FU
brmfmac
- support two station interfaces concurrently
bcma
- support SPROM rev 11
====================
Link: https://lore.kernel.org/r/20221028132943.304ECC433B5@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All drivers are now using mac80211 internal queues (iTXQs).
Drop mac80211 internal support for the old push path.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If beacon protection is active but the beacon cannot be
decrypted or is otherwise malformed, we call the cfg80211
API to report this to userspace, but that uses a netdev
pointer, which isn't present for P2P-Device. Fix this to
call it only conditionally to ensure cfg80211 won't crash
in the case of P2P-Device.
This fixes CVE-2022-42722.
Reported-by: Sönke Huster <shuster@seemoo.tu-darmstadt.de>
Fixes: 9eaf183af7 ("mac80211: Report beacon protection failures to user space")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since AP_VLAN interfaces are not passed to the driver, check offload_flags
on the bss vif instead.
Reported-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Fixes: 80a915ec44 ("mac80211: add rx decapsulation offload support")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since STP TCN frames are only 7 bytes, the pskb_may_pull call returns an error.
Instead of dropping those packets, bump them back to the slow path for proper
processing.
Fixes: 49ddf8e6e2 ("mac80211: add fast-rx path")
Reported-by: Chad Monroe <chad.monroe@smartrg.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Few stack changes and lots of driver changes in this round. brcmfmac
has more activity as usual and it gets new hardware support. ath11k
improves WCN6750 support and also other smaller features. And of
course changes all over.
Note: in early September wireless tree was merged to wireless-next to
avoid some conflicts with mac80211 patches, this shouldn't cause any
problems but wanted to mention anyway.
Major changes:
mac80211
* refactoring and preparation for Wi-Fi 7 Multi-Link Operation (MLO)
feature continues
brcmfmac
* support CYW43439 SDIO chipset
* support BCM4378 on Apple platforms
* support CYW89459 PCIe chipset
rtw89
* more work to get rtw8852c supported
* P2P support
* support for enabling and disabling MSDU aggregation via nl80211
mt76
* tx status reporting improvements
ath11k
* cold boot calibration support on WCN6750
* Target Wake Time (TWT) debugfs support for STA interface
* support to connect to a non-transmit MBSSID AP profile
* enable remain-on-channel support on WCN6750
* implement SRAM dump debugfs interface
* enable threaded NAPI on all hardware
* WoW support for WCN6750
* support to provide transmit power from firmware via nl80211
* support to get power save duration for each client
* spectral scan support for 160 MHz
wcn36xx
* add SNR from a received frame as a source of system entropy
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmM3BGYRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZuR3Af/XiuMlnDB6flq+M/kQHLWWvHybLw5aCJ7
l3yXhNFWxpBl2hQXtj17JSjVCYQmxbfrgRqhbNhyACO25bpymCb5QctB9X+Y7TwL
250JmuKvQfFx5oJNRfJ67dKTf3raloQYbdEMJNqySgebL+eSfrDskc9vaCLVDmCK
I994fl0Q1wUbJ6fbuIFd07ti8ay6UlSS/iakv4+nEeimabtZWJWlXBWYRpKpikdP
h9z2kPtss6yz6seaQuw6ny+qysYLi11Tp+Cued9XR3dWOOhB2X1tLHH0H02xPw76
9OJZEJHycP2juxjMfAaktHY+VX36GPLsMLUTVusH0h/Fdy3VG8YSAw==
=emmG
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-09-30' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.1
Few stack changes and lots of driver changes in this round. brcmfmac
has more activity as usual and it gets new hardware support. ath11k
improves WCN6750 support and also other smaller features. And of
course changes all over.
Note: in early September wireless tree was merged to wireless-next to
avoid some conflicts with mac80211 patches, this shouldn't cause any
problems but wanted to mention anyway.
Major changes:
mac80211
- refactoring and preparation for Wi-Fi 7 Multi-Link Operation (MLO)
feature continues
brcmfmac
- support CYW43439 SDIO chipset
- support BCM4378 on Apple platforms
- support CYW89459 PCIe chipset
rtw89
- more work to get rtw8852c supported
- P2P support
- support for enabling and disabling MSDU aggregation via nl80211
mt76
- tx status reporting improvements
ath11k
- cold boot calibration support on WCN6750
- Target Wake Time (TWT) debugfs support for STA interface
- support to connect to a non-transmit MBSSID AP profile
- enable remain-on-channel support on WCN6750
- implement SRAM dump debugfs interface
- enable threaded NAPI on all hardware
- WoW support for WCN6750
- support to provide transmit power from firmware via nl80211
- support to get power save duration for each client
- spectral scan support for 160 MHz
wcn36xx
- add SNR from a received frame as a source of system entropy
* tag 'wireless-next-2022-09-30' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (231 commits)
wifi: rtl8xxxu: Improve rtl8xxxu_queue_select
wifi: rtl8xxxu: Fix AIFS written to REG_EDCA_*_PARAM
wifi: rtl8xxxu: gen2: Enable 40 MHz channel width
wifi: rtw89: 8852b: configure DLE mem
wifi: rtw89: check DLE FIFO size with reserved size
wifi: rtw89: mac: correct register of report IMR
wifi: rtw89: pci: set power cut closed for 8852be
wifi: rtw89: pci: add to do PCI auto calibration
wifi: rtw89: 8852b: implement chip_ops::{enable,disable}_bb_rf
wifi: rtw89: add DMA busy checking bits to chip info
wifi: rtw89: mac: define DMA channel mask to avoid unsupported channels
wifi: rtw89: pci: mask out unsupported TX channels
iwlegacy: Replace zero-length arrays with DECLARE_FLEX_ARRAY() helper
ipw2x00: Replace zero-length array with DECLARE_FLEX_ARRAY() helper
wifi: iwlwifi: Track scan_cmd allocation size explicitly
brcmfmac: Remove the call to "dtim_assoc" IOVAR
brcmfmac: increase dcmd maximum buffer size
brcmfmac: Support 89459 pcie
brcmfmac: increase default max WOWL patterns to 16
cw1200: fix incorrect check to determine if no element is found in list
...
====================
Link: https://lore.kernel.org/r/20220930150413.A7984C433D6@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pskb_may_pull already contains all of the checks performed by
pskb_pull.
Use pskb_may_pull for validation in pskb_pull, eliminating the
duplication and making __pskb_pull obsolete.
Replace __pskb_pull with pskb_pull where applicable.
Signed-off-by: Richard Gobert <richardbgobert@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/freescale/fec.h
7d650df99d ("net: fec: add pm_qos support on imx6q platform")
40c79ce13b ("net: fec: add stop mode support for imx8 platform")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The SMPS power save mode needs to be per-link rather than being shared
for all links. As such, move it into struct ieee80211_link_sta.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use rx->link_sta everywhere instead of accessing the default link.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Now that we have a link_sta pointer in the rx struct
we also need to fill it in all the cases. It didn't
matter so much until now as we weren't using it, but
the code should really be able to assume that if the
rx.sta is set, so is rx.link_sta.
Fixes: ccdde7c74f ("wifi: mac80211: properly implement MLO key handling")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The rx data link pointer isn't set from the RX aggregation timer,
resulting in a later warning. Fix that by setting it to the first
valid link for now, with a FIXME to worry about statistics later,
it's not very important since it's just the timeout case.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/498d714c-76be-9d04-26db-a1206878de5e@redhat.com
Fixes: 56057da456 ("wifi: mac80211: rx: track link in RX data")
Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When queuing frames to an interface store the link ID we
determined (which possibly came from the driver in the
RX status in the first place) in the RX status, and use
it in the MLME code to send probe responses, beacons and
CSA frames to the right link.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With link_id reported in rx_status for MLO connection, do the
stats update on the appropriate link instead of always deflink.
Signed-off-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com>
Link: https://lore.kernel.org/r/20220817104213.2531-3-quic_vthiagar@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In MLO, when the address translation from link to MLD is done
in fw/hw, it is necessary to be able to have some information
on the link on which the frame has been received. Extend the
rx API to include link_id and a valid flag in ieee80211_rx_status.
Also make chanes to mac80211 rx APIs to make use of the reported
link_id after sanity checks.
Signed-off-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com>
Link: https://lore.kernel.org/r/20220817104213.2531-2-quic_vthiagar@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement key installation and lookup (on TX and RX)
for MLO, so we can use multiple GTKs/IGTKs/BIGTKs.
Co-authored-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We'll need the link e.g. for decrypt, and shouldn't be
looking it up all the time later, so track it in the RX
data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a couple of new things that should be possible
with MLO:
* selecting the link to transmit to a station by link ID,
which a previous patch added to the nl80211 API
* selecting the link by frequency, similarly
* allowing transmittion to an MLD without specifying any
channel or link ID, with MLD addresses
Enable these use cases. Also fix the address comparison
in client mode to use the AP (MLD) address.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the low level driver reports hardware timestamps for frame
TX status or frame RX, pass the timestamps to cfg80211.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We should only translate addr3 here if it's the BSSID.
Fixes: 42fb9148c0 ("wifi: mac80211: do link->MLD address translation on RX")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some cases, e.g. with Qualcomm devices and management
frames, or in hwsim, frames may be reported from the driver
with link addresses, but for decryption and matching needs
we really want to have them with MLD addresses. Support the
translation on RX.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow link source address on TX.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow transmitting EAPOL frames not only from the interface
address (which is the MLD address) but also any link addresses,
in order to support non-MLO stations on AP interfaces.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since links can be added and removed dynamically, we need to
somehow protect the sdata->link[] and vif->link_conf[] array
pointers from disappearing when accessing them without locks.
RCU-ify the pointers to achieve this, which requires quite a
bit of rework.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When checking whether or not to accept a frame in RX,
take into account the configured link addresses. Also
look up the link station correctly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commits 6a789ba679 and
2433647bc8.
The virtual time scheduler code has a number of issues:
- queues slowed down by hardware/firmware powersave handling were not properly
handled.
- on ath10k in push-pull mode, tx queues that the driver tries to pull from
were starved, causing excessive latency
- delay between tx enqueue and reported airtime use were causing excessively
bursty tx behavior
The bursty behavior may also be present on the round-robin scheduler, but there
it is much easier to fix without introducing additional regressions
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://lore.kernel.org/r/20220625212411.36675-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce the capability to specify gfp_t parameter to
ieeee80211_obss_color_collision_notify routine since it runs in
interrupt context in ieee80211_rx_check_bss_color_collision().
Fixes: 6d945a33f2 ("mac80211: introduce BSS color collision detection")
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/02c990fb3fbd929c8548a656477d20d6c0427a13.1655419135.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We need to be able to access these in a race-free way under
traffic while adding/removing them, so RCU-ify the pointers.
This requires passing a link_sta to a lot of functions so
we don't have to do the RCU handling everywhere.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make the channel context code MLO aware, along with some
functions that it uses, so that the chan.c file is now
MLD-clean and no longer uses deflink/bss_conf/etc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Start reorganizing interface related data structures toward
MLD. The most complex part here is for the keys, since we
have to split the various kinds of GTKs off to the link but
still need to use (for WEP) the other keys as a fallback
even for multicast frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To add MLD, reuse the bss_conf structure later for per-link
information, so move some things into it that are per link.
Most transformations were done with the following spatch:
@@
expression sdata;
identifier var = { chanctx_conf, mu_mimo_owner, csa_active, color_change_active, color_change_color };
@@
-sdata->vif.var
+sdata->vif.bss_conf.var
@@
struct ieee80211_vif *vif;
identifier var = { chanctx_conf, mu_mimo_owner, csa_active, color_change_active, color_change_color };
@@
-vif->var
+vif->bss_conf.var
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg