It could decrease one condition check to collect some statements in the
first condition block.
Signed-off-by: Gao Feng <gfree.wind@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The bridge loop avoidance (BLA) feature of batman-adv sends packets to
probe for Mesh/LAN packet loops. Those packets are not sent by real
clients and should therefore not be added to the translation table (TT).
Signed-off-by: Simon Wunderlich <simon.wunderlich@open-mesh.com>
The network stack no longer uses the last_rx member of struct net_device
since the bonding driver switched to use its own private last_rx in
commit 9f24273837 ("bonding: use last_arp_rx in slave_last_rx()").
However, some drivers still (ab)use the field for their own purposes and
some driver just update it without actually using it.
Previously, there was an accompanying comment for the last_rx member
added in commit 4dc89133f4 ("net: add a comment on netdev->last_rx")
which asked drivers not to update is, unless really needed. However,
this commend was removed in commit f8ff080dac ("bonding: remove
useless updating of slave->dev->last_rx"), so some drivers added later
on still did update last_rx.
Remove all usage of last_rx and switch three drivers (sky2, atp and
smc91c92_cs) which actually read and write it to use their own private
copy in netdev_priv.
Compile-tested with allyesconfig and allmodconfig on x86 and arm.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An error before the hardif is found has to free the skb. But every error
after that has to free the skb + put the hard interface.
Fixes: 8def0be82d ("batman-adv: Consume skb in batadv_frag_send_packet")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
batadv_tt_prepare_tvlv_local_data can fail to allocate the memory for the
new TVLV block. The caller is informed about this problem with the returned
length of 0. Not checking this value results in an invalid memory access
when either tt_data or tt_change is accessed.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 7ea7b4a142 ("batman-adv: make the TT CRC logic VLAN specific")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
- 6 patches adding functionality to detect a WiFi interface under
other virtual interfaces, like VLANs. They introduce a cache for
the detected the WiFi configuration to avoid RTNL locking in
critical sections. Patches have been prepared by Marek Lindner
and Sven Eckelmann
- Enable automatic module loading for genl requests, by Sven Eckelmann
- Fix a potential race condition on interface removal. This is not
happening very often in practice, but requires bigger changes to fix,
so we are sending this to net-next. By Linus Luessing
-----BEGIN PGP SIGNATURE-----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=Pdlv
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20161119' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature patchset includes the following changes:
- 6 patches adding functionality to detect a WiFi interface under
other virtual interfaces, like VLANs. They introduce a cache for
the detected the WiFi configuration to avoid RTNL locking in
critical sections. Patches have been prepared by Marek Lindner
and Sven Eckelmann
- Enable automatic module loading for genl requests, by Sven Eckelmann
- Fix a potential race condition on interface removal. This is not
happening very often in practice, but requires bigger changes to fix,
so we are sending this to net-next. By Linus Luessing
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- netlink and code cleanups by Sven Eckelmann (3 patches)
- Cleanup and minor fixes by Linus Luessing (3 patches)
- Speed up multicast update intervals, by Linus Luessing
- Avoid (re)broadcast in meshes for some easy cases,
by Linus Luessing
- Clean up tx return state handling, by Sven Eckelmann (6 patches)
- Fix some special mac address handling cases, by Sven Eckelmann
(3 patches)
-----BEGIN PGP SIGNATURE-----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=1xrj
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20161108-v2' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
pull request for net-next: batman-adv 2016-11-08 v2
This feature and cleanup patchset includes the following changes:
- netlink and code cleanups by Sven Eckelmann (3 patches)
- Cleanup and minor fixes by Linus Luessing (3 patches)
- Speed up multicast update intervals, by Linus Luessing
- Avoid (re)broadcast in meshes for some easy cases,
by Linus Luessing
- Clean up tx return state handling, by Sven Eckelmann (6 patches)
- Fix some special mac address handling cases, by Sven Eckelmann
(3 patches)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In rare cases during shutdown the following general protection fault can
happen:
general protection fault: 0000 [#1] SMP
Modules linked in: batman_adv(O-) [...]
CPU: 3 PID: 1714 Comm: rmmod Tainted: G O 4.6.0-rc6+ #1
[...]
Call Trace:
[<ffffffffa0363294>] batadv_hardif_disable_interface+0x29a/0x3a6 [batman_adv]
[<ffffffffa0373db4>] batadv_softif_destroy_netlink+0x4b/0xa4 [batman_adv]
[<ffffffff813b52f3>] __rtnl_link_unregister+0x48/0x92
[<ffffffff813b9240>] rtnl_link_unregister+0xc1/0xdb
[<ffffffff8108547c>] ? bit_waitqueue+0x87/0x87
[<ffffffffa03850d2>] batadv_exit+0x1a/0xf48 [batman_adv]
[<ffffffff810c26f9>] SyS_delete_module+0x136/0x1b0
[<ffffffff8144dc65>] entry_SYSCALL_64_fastpath+0x18/0xa8
[<ffffffff8108aaca>] ? trace_hardirqs_off_caller+0x37/0xa6
Code: 89 f7 e8 21 bd 0d e1 4d 85 e4 75 0e 31 f6 48 c7 c7 50 d7 3b a0 e8 50 16 f2 e0 49 8b 9c 24 28 01 00 00 48 85 db 0f 84 b2 00 00 00 <48> 8b 03 4d 85 ed 48 89 45 c8 74 09 4c 39 ab f8 00 00 00 75 1c
RIP [<ffffffffa0371852>] batadv_purge_outstanding_packets+0x1c8/0x291 [batman_adv]
RSP <ffff88001da5fd78>
---[ end trace 803b9bdc6a4a952b ]---
Kernel panic - not syncing: Fatal exception in interrupt
Kernel Offset: disabled
---[ end Kernel panic - not syncing: Fatal exception in interrupt
It does not happen often, but may potentially happen when frequently
shutting down and reinitializing an interface. With some carefully
placed msleep()s/mdelay()s it can be reproduced easily.
The issue is, that on interface removal, any still running worker thread
of a forwarding packet will race with the interface purging routine to
free a forwarding packet. Temporarily giving up a spin-lock to be able
to sleep in the purging routine is not safe.
Furthermore, there is a potential general protection fault not just for
the purging side shown above, but also on the worker side: Temporarily
removing a forw_packet from the according forw_{bcast,bat}_list will make
it impossible for the purging routine to catch and cancel it.
# How this patch tries to fix it:
With this patch we split the queue purging into three steps: Step 1),
removing forward packets from the queue of an interface and by that
claim it as our responsibility to free.
Step 2), we are either lucky to cancel a pending worker before it starts
to run. Or if it is already running, we wait and let it do its thing,
except two things:
Through the claiming in step 1) we prevent workers from a) re-arming
themselves. And b) prevent workers from freeing packets which we still
hold in the interface purging routine.
Finally, step 3, we are sure that no forwarding packets are pending or
even running anymore on the interface to remove. We can then safely free
the claimed forwarding packets.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The batman-adv module has to be loaded to fulfill genl request by the
userspace. When it is not loaded then requests will fail. It is therefore
useful to get the module automatically loaded when such a request is made.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Things like VLANs don't have their link set when they are created. Thus
the wifi flags have to be evaluated later to fix their contents for the
link interface.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
[sven.eckelmann@open-mesh.com: re-add batadv_get_real_netdev to take rtnl
semaphore for batadv_get_real_netdevice]
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
In a few situations batman-adv tries to determine whether a given interface
is a WiFi interface to enable specific WiFi optimizations. If the interface
batman-adv has been configured with is a virtual interface (e.g. VLAN) it
would not be properly detected as WiFi interface and thus not benefit from
the special WiFi treatment.
This patch changes that by peeking under the hood whenever a virtual
interface is in play.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
[sven.eckelmann@open-mesh.com: integrate in wifi_flags caching, retrieve
namespace of link interface]
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
batman-adv is requiring the type of wifi device in different contexts. Some
of them can take the rtnl semaphore and some of them already have the
semaphore taken. But even others don't allow that the semaphore will be
taken.
The data has to be retrieved when the hardif is added to batman-adv because
some of the wifi information for an hardif will only be available with rtnl
lock. It can then be cached in the batadv_hard_iface and the functions
is_wifi_netdev and is_cfg80211_netdev can just compare the correct bits
without imposing extra locking requirements.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The ELP protocol requires cfg80211 to auto-detect the WiFi througput
to a given neighbor. Use batadv_is_cfg80211_netdev() to determine
whether or not an interface is eligible.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
An unicast batman-adv packet cannot be transmitted to a multicast or zero
mac address. So reject incoming packets which still have these classes of
addresses as destination mac address in the outer ethernet header.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The returned net_namespace of batadv_getlink_net may be used with functions
that potentially modify the struct. Thus it must return the pointer as
non-const like rtnl_link_ops::get_link_net does.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The routing check for management frames is validating the source mac
address in the outer ethernet header. It rejects every source mac address
which is a broadcast address. But it also has to reject the zero-mac
address and multicast mac addresses.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The routing checks are validating the source mac address of the outer
ethernet header. They reject every source mac address which is a broadcast
address. But they also have to reject any multicast mac addresses.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[sw@simonwunderlich.de: fix commit message typo]
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
No caller of batadv_send_skb_to_orig is expecting the results to be -1
(-EPERM) anymore when the skbuff was not consumed. They will instead expect
that the skbuff is always consumed. Having such return code filter is
therefore not needed anymore.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Receiving functions in Linux consume the supplied skbuff. Doing the same in
the batadv_rx_handler functions makes the behavior more similar to the rest
of the Linux network code.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The throughput meter detects different situations as problems for the
current test. It stops the test after these and reports it to userspace.
This also has to be done when the primary interface disappeared during the
test.
Fixes: 33a3bb4a33 ("batman-adv: throughput meter implementation")
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The commit 9799c50372 ("batman-adv: fix splat on disabling an interface")
fixed a warning but at the same time broke the rtnl function add_slave for
devices which were temporarily removed.
batadv_softif_slave_add requires soft_iface of and hard_iface to be NULL
before it is allowed to be enslaved. But this resetting of soft_iface to
NULL in batadv_hardif_disable_interface was removed with the aforementioned
commit.
Reported-by: Julian Labus <julian@freifunk-rtk.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Sending functions in Linux consume the supplied skbuff. Doing the same in
batadv_send_skb_to_orig avoids the hack of returning -1 (-EPERM) to signal
the caller that he is responsible for cleaning up the skb.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Sending functions in Linux consume the supplied skbuff. Doing the same in
batadv_frag_send_packet avoids the hack of returning -1 (-EPERM) to signal
the caller that he is responsible for cleaning up the skb.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
A failure during the submission also causes dropped packets.
batadv_interface_tx should therefore also increase the DROPPED counter for
these returns.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
kfree_skb assumes that an skb is dropped after an failure and notes that.
consume_skb should be used in non-failure situations. Such information is
important for dropmonitor netlink which tells how many packets were dropped
and where this drop happened.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
With this patch, (re)broadcasting on a specific interfaces is avoided:
* No neighbor: There is no need to broadcast on an interface if there
is no node behind it.
* Single neighbor is source: If there is just one neighbor on an
interface and if this neighbor is the one we actually got this
broadcast packet from, then we do not need to echo it back.
* Single neighbor is originator: If there is just one neighbor on
an interface and if this neighbor is the originator of this
broadcast packet, then we do not need to echo it back.
Goodies for BATMAN V:
("Upgrade your BATMAN IV network to V now to get these for free!")
Thanks to the split of OGMv1 into two packet types, OGMv2 and ELP
that is, we can now apply the same optimizations stated above to OGMv2
packets, too.
Furthermore, with BATMAN V, rebroadcasts can be reduced in certain
multi interface cases, too, where BATMAN IV cannot. This is thanks to
the removal of the "secondary interface originator" concept in BATMAN V.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Instead of latching onto the OGM period, this patch introduces a worker
dedicated to multicast TT and TVLV updates.
The reasoning is, that upon roaming especially the translation table
should be updated timely to minimize connectivity issues.
With BATMAN V, the idea is to greatly increase the OGM interval to
reduce overhead. Unfortunately, right now this could lead to
a bad user experience if multicast traffic is involved.
Therefore this patch introduces a fixed 500ms update interval for
multicast TT entries and the multicast TVLV.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
During broadcast queueing, the skb_reset_mac_header() sets the skb
to a place invalid for a MAC header, pointing right into the
batman-adv broadcast packet. Luckily, no one seems to actually use
eth_hdr(skb) afterwards until batadv_send_skb_packet() resets the
header to a valid position again.
Therefore removing this unnecessary, weird skb_reset_mac_header()
call.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
batadv_mcast_mla_list_free() just frees some leftovers of a local feast
in batadv_mcast_mla_update(). No lockdep needed as it has nothing to do
with bat_priv->mcast.mla_list.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The genl_ops don't need to be written by anyone and thus can be moved in a
ro memory range.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Fixes: 56989f6d85 ("genetlink: mark families as __ro_after_init")
Fixes: 2ae0f17df1 ("genetlink: use idr to track families")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
order):
- bump version strings, by Simon Wunderlich
- README updates/clean up, by Sven Eckelmann (4 patches)
- Code clean up and restructuring by Sven Eckelmann (2 patches)
- Kerneldoc fix in forw_packet structure, by Linus Luessing
- Remove unused argument in dbg_arp, by Antonio Quartulli
- Add support to build batman-adv without wireless, by Linus Luessing
- Restructure error handling for is_ap_isolated, by Markus Elfring
- Remove unused initialization in various functions, by Sven Eckelmann
- Use better names for fragment and gateway list heads, by Sven
Eckelmann (2 patches)
- Convert to octal permissions for files, by Sven Eckelmann
- Avoid precedence issues for some macros, by Sven Eckelmann
-----BEGIN PGP SIGNATURE-----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=eDGz
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20161027' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This code cleanup patchset includes the following changes (chronological
order):
- bump version strings, by Simon Wunderlich
- README updates/clean up, by Sven Eckelmann (4 patches)
- Code clean up and restructuring by Sven Eckelmann (2 patches)
- Kerneldoc fix in forw_packet structure, by Linus Luessing
- Remove unused argument in dbg_arp, by Antonio Quartulli
- Add support to build batman-adv without wireless, by Linus Luessing
- Restructure error handling for is_ap_isolated, by Markus Elfring
- Remove unused initialization in various functions, by Sven Eckelmann
- Use better names for fragment and gateway list heads, by Sven
Eckelmann (2 patches)
- Convert to octal permissions for files, by Sven Eckelmann
- Avoid precedence issues for some macros, by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now genl_register_family() is the only thing (other than the
users themselves, perhaps, but I didn't find any doing that)
writing to the family struct.
In all families that I found, genl_register_family() is only
called from __init functions (some indirectly, in which case
I've add __init annotations to clarifly things), so all can
actually be marked __ro_after_init.
This protects the data structure from accidental corruption.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of providing macros/inline functions to initialize
the families, make all users initialize them statically and
get rid of the macros.
This reduces the kernel code size by about 1.6k on x86-64
(with allyesconfig).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Static family IDs have never really been used, the only
use case was the workaround I introduced for those users
that assumed their family ID was also their multicast
group ID.
Additionally, because static family IDs would never be
reserved by the generic netlink code, using a relatively
low ID would only work for built-in families that can be
registered immediately after generic netlink is started,
which is basically only the control family (apart from
the workaround code, which I also had to add code for so
it would reserve those IDs)
Thus, anything other than GENL_ID_GENERATE is flawed and
luckily not used except in the cases I mentioned. Move
those workarounds into a few lines of code, and then get
rid of GENL_ID_GENERATE entirely, making it more robust.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum MTU is defined via the slave devices of an batman-adv
interface. Thus it is not possible to calculate the max_mtu during the
creation of the batman-adv device when no slave devices are attached. Doing
so would for example break non-fragmentation setups which then
(incorrectly) allow an MTU of 1500 even when underlying device cannot
transport 1500 bytes + batman-adv headers.
Checking the dynamically calculated max_mtu via the minimum of the slave
devices MTU during .ndo_change_mtu is also used by the bridge interface.
Cc: Jarod Wilson <jarod@redhat.com>
Fixes: b3e3893e12 ("net: use core MTU range checking in misc drivers")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As long as there is still a reference for a hard interface held, there might
still be a forwarding packet relying on its attributes.
Therefore avoid setting hard_iface->soft_iface to NULL when disabling a hard
interface.
This fixes the following, potential splat:
batman_adv: bat0: Interface deactivated: eth1
batman_adv: bat0: Removing interface: eth1
cgroup: new mount options do not match the existing superblock, will be ignored
batman_adv: bat0: Interface deactivated: eth3
batman_adv: bat0: Removing interface: eth3
------------[ cut here ]------------
WARNING: CPU: 3 PID: 1986 at ./net/batman-adv/bat_iv_ogm.c:549 batadv_iv_send_outstanding_bat_ogm_packet+0x145/0x643 [batman_adv]
Modules linked in: batman_adv(O-) <...>
CPU: 3 PID: 1986 Comm: kworker/u8:2 Tainted: G W O 4.6.0-rc6+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
Workqueue: bat_events batadv_iv_send_outstanding_bat_ogm_packet [batman_adv]
0000000000000000 ffff88001d93bca0 ffffffff8126c26b 0000000000000000
0000000000000000 ffff88001d93bcf0 ffffffff81051615 ffff88001f19f818
000002251d93bd68 0000000000000046 ffff88001dc04a00 ffff88001becbe48
Call Trace:
[<ffffffff8126c26b>] dump_stack+0x67/0x90
[<ffffffff81051615>] __warn+0xc7/0xe5
[<ffffffff8105164b>] warn_slowpath_null+0x18/0x1a
[<ffffffffa0356f24>] batadv_iv_send_outstanding_bat_ogm_packet+0x145/0x643 [batman_adv]
[<ffffffff8108b01f>] ? __lock_is_held+0x32/0x54
[<ffffffff810689a2>] process_one_work+0x2a8/0x4f5
[<ffffffff81068856>] ? process_one_work+0x15c/0x4f5
[<ffffffff81068df2>] worker_thread+0x1d5/0x2c0
[<ffffffff81068c1d>] ? process_scheduled_works+0x2e/0x2e
[<ffffffff81068c1d>] ? process_scheduled_works+0x2e/0x2e
[<ffffffff8106dd90>] kthread+0xc0/0xc8
[<ffffffff8144de82>] ret_from_fork+0x22/0x40
[<ffffffff8106dcd0>] ? __init_kthread_worker+0x55/0x55
---[ end trace 647f9f325123dc05 ]---
What happened here is, that there was still a forw_packet (here: a BATMAN IV
OGM) in the queue of eth3 with the forw_packet->if_incoming set to eth1 and the
forw_packet->if_outgoing set to eth3.
When eth3 is to be deactivated and removed, then this thread waits for the
forw_packet queued on eth3 to finish. Because eth1 was deactivated and removed
earlier and by that had forw_packet->if_incoming->soft_iface, set to NULL, the
splat when trying to send/flush the OGM on eth3 occures.
Fixes: c6c8fea297 ("net: Add batman-adv meshing protocol")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
[sven@narfation.org: Reduced size of Oops message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
firewire-net:
- set min/max_mtu
- remove fwnet_change_mtu
nes:
- set max_mtu
- clean up nes_netdev_change_mtu
xpnet:
- set min/max_mtu
- remove xpnet_dev_change_mtu
hippi:
- set min/max_mtu
- remove hippi_change_mtu
batman-adv:
- set max_mtu
- remove batadv_interface_change_mtu
- initialization is a little async, not 100% certain that max_mtu is set
in the optimal place, don't have hardware to test with
rionet:
- set min/max_mtu
- remove rionet_change_mtu
slip:
- set min/max_mtu
- streamline sl_change_mtu
um/net_kern:
- remove pointless ndo_change_mtu
hsi/clients/ssi_protocol:
- use core MTU range checking
- remove now redundant ssip_pn_set_mtu
ipoib:
- set a default max MTU value
- Note: ipoib's actual max MTU can vary, depending on if the device is in
connected mode or not, so we'll just set the max_mtu value to the max
possible, and let the ndo_change_mtu function continue to validate any new
MTU change requests with checks for CM or not. Note that ipoib has no
min_mtu set, and thus, the network core's mtu > 0 check is the only lower
bounds here.
mptlan:
- use net core MTU range checking
- remove now redundant mpt_lan_change_mtu
fddi:
- min_mtu = 21, max_mtu = 4470
- remove now redundant fddi_change_mtu (including export)
fjes:
- min_mtu = 8192, max_mtu = 65536
- The max_mtu value is actually one over IP_MAX_MTU here, but the idea is to
get past the core net MTU range checks so fjes_change_mtu can validate a
new MTU against what it supports (see fjes_support_mtu in fjes_hw.c)
hsr:
- min_mtu = 0 (calls ether_setup, max_mtu is 1500)
f_phonet:
- min_mtu = 6, max_mtu = 65541
u_ether:
- min_mtu = 14, max_mtu = 15412
phonet/pep-gprs:
- min_mtu = 576, max_mtu = 65530
- remove redundant gprs_set_mtu
CC: netdev@vger.kernel.org
CC: linux-rdma@vger.kernel.org
CC: Stefan Richter <stefanr@s5r6.in-berlin.de>
CC: Faisal Latif <faisal.latif@intel.com>
CC: linux-rdma@vger.kernel.org
CC: Cliff Whickman <cpw@sgi.com>
CC: Robin Holt <robinmholt@gmail.com>
CC: Jes Sorensen <jes@trained-monkey.org>
CC: Marek Lindner <mareklindner@neomailbox.ch>
CC: Simon Wunderlich <sw@simonwunderlich.de>
CC: Antonio Quartulli <a@unstable.cc>
CC: Sathya Prakash <sathya.prakash@broadcom.com>
CC: Chaitra P B <chaitra.basappa@broadcom.com>
CC: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
CC: MPT-FusionLinux.pdl@broadcom.com
CC: Sebastian Reichel <sre@kernel.org>
CC: Felipe Balbi <balbi@kernel.org>
CC: Arvid Brodin <arvid.brodin@alten.se>
CC: Remi Denis-Courmont <courmisch@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It must be avoided that arguments to a macro are evaluated ungrouped (which
enforces normal operator precendence). Otherwise the result of the macro
is not well defined.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Linus prefers to have octal permission numbers instead of combinations of
macro names ("random line noise"). Also old existing "bad symbolic
permission bit macro use" should be converted to octal numbers.
(http://lkml.kernel.org/r/CA+55aFw5v23T-zvDZp-MmD_EYxF8WbafwwB59934FV7g21uMGQ@mail.gmail.com)
Also remove the S_IFREG bit from the octal representation because it is
filtered out by debugfs_create.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The batman-adv codebase is using "list" for the list node (prev/next) and
<list content descriptor>+"_list" for the head of a list. Not using this
naming scheme can up in confusions when reading the code.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The batman-adv codebase is using "list" for the list node (prev/next) and
<list content descriptor>+"_list" for the head of a list. Not using this
naming scheme can up in confusions because list_head is used for both the
head of the list and the list node (prev/next) in each item of the list.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Some variables are overwritten immediatelly in a functions. These don't
have to be initialized to a specific value on the stack because the value
will be overwritten before they will be used anywhere.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The variables "tt_local_entry" and "tt_global_entry" were eventually
checked again despite of a corresponding null pointer test before.
* Avoid this double check by reordering a function call sequence
and the better selection of jump targets.
* Omit the initialisation for these variables at the beginning then.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
With the new stub for cfg80211_get_station(), we can now build the
BATMAN V protocol even with a kernel that was built without any
wireless support.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The argument "type" passed to the batadv_dbg_arp() function is
never used. Remove it.
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The forw_packet list node is wrongly attributed to the icmp socket code.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The function batadv_sum_counter is only used in soft-interface.c and has no
special relevance for main.h.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The BATADV_DBG_ALL has to contain the bit of BATADV_DBG_TP_METER to really
support all available debug messages.
Fixes: 33a3bb4a33 ("batman-adv: throughput meter implementation")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The batadv_hard_iface::neigh_list is accessed via rcu based primitives.
Thus all operations done on it have to fulfill the requirements by RCU. So
using non-RCU mechanisms like hlist_add_head is not allowed because it
misses the barriers required to protect concurrent readers when accessing
the data behind the pointer.
Fixes: cef63419f7 ("batman-adv: add list of unique single hop neighbors per hard-interface")
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Acked-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Kernel source files need not include <linux/kconfig.h> explicitly
because the top Makefile forces to include it with:
-include $(srctree)/include/linux/kconfig.h
This commit removes explicit includes except the following:
* arch/s390/include/asm/facilities_src.h
* tools/testing/radix-tree/linux/kernel.h
These two are used for host programs.
Link: http://lkml.kernel.org/r/1473656164-11929-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The skb_reserve() call only reserved headroom for the mac header, but
not the elp packet header itself.
Fixing this by using skb_put()'ing towards the skb tail instead of
skb_push()'ing towards the skb head.
Fixes: d6f94d91f7 ("batman-adv: ELP - adding basic infrastructure")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
batadv_find_router dereferences last_bonding_candidate from
orig_node without making sure that it has a valid reference. This reference
has to be retrieved by increasing the reference counter while holding
neigh_list_lock. The lock is required to avoid that
batadv_last_bonding_replace removes the current last_bonding_candidate,
reduces the reference counter and maybe destroys the object in this
process.
Fixes: f3b3d90189 ("batman-adv: add bonding again")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The files provided by batman-adv via debugfs are currently converted to
netlink. Tools which are not yet converted to use the netlink interface may
still rely on the old debugfs files. But systems which already upgraded
their tools can save some space by disabling this feature. The default
configuration of batman-adv on amd64 can reduce the size of the module by
around 11% when this feature is disabled.
$ size net/batman-adv/batman-adv.ko*
text data bss dec hex filename
150507 10395 4160 165062 284c6 net/batman-adv/batman-adv.ko.y
137106 7099 2112 146317 23b8d net/batman-adv/batman-adv.ko.n
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Switch-like virtual interfaces like bridge or openvswitch don't destroy
itself when all their attached netdevices dissappear. Instead they only
remove the link to the unregistered device and keep working until they get
removed manually.
This has the benefit that all configurations for this interfaces are kept
and daemons reacting to rtnl events can just add new slave interfaces
without going through the complete configuration of the switch-like
netdevice.
Handling unregister events of client devices similar in batman-adv allows
users to drop their current workaround of dummy netdevices attached to
batman-adv soft-interfaces.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
It is hard to understand why the refcnt is increased when it isn't done
near the actual place the new reference is used. So using kref_get right
before the place which requires the reference and in the same function
helps to avoid accidental problems caused by incorrect reference counting.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
It is hard to understand why the refcnt is increased when it isn't done
near the actual place the new reference is used. So using kref_get right
before the place which requires the reference and in the same function
helps to avoid accidental problems caused by incorrect reference counting.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
It is hard to understand why the refcnt is increased when it isn't done
near the actual place the new reference is used. So using kref_get right
before the place which requires the reference and in the same function
helps to avoid accidental problems caused by incorrect reference counting.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
It is hard to understand why the refcnt is increased when it isn't done
near the actual place the new reference is used. So using kref_get right
before the place which requires the reference and in the same function
helps to avoid accidental problems caused by incorrect reference counting.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
It is hard to understand why the refcnt is increased when it isn't done
near the actual place the new reference is used. So using kref_get right
before the place which requires the reference and in the same function
helps to avoid accidental problems caused by incorrect reference counting.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
It is hard to understand why the refcnt is increased when it isn't done
near the actual place the new reference is used. So using kref_get right
before the place which requires the reference and in the same function
helps to avoid accidental problems caused by incorrect reference counting.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
It is hard to understand why the refcnt is increased when it isn't done
near the actual place the new reference is used. So using kref_get right
before the place which requires the reference and in the same function
helps to avoid accidental problems caused by incorrect reference counting.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
It is hard to understand why the refcnt is increased when it isn't done
near the actual place the new reference is used. So using kref_get right
before the place which requires the reference and in the same function
helps to avoid accidental problems caused by incorrect reference counting.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
It is hard to understand why the refcnt is increased when it isn't done
near the actual place the new reference is used. So using kref_get right
before the place which requires the reference and in the same function
helps to avoid accidental problems caused by incorrect reference counting.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
It is hard to understand why the refcnt is increased when it isn't done
near the actual place the new reference is used. So using kref_get right
before the place which requires the reference and in the same function
helps to avoid accidental problems caused by incorrect reference counting.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
It is hard to understand why the refcnt is increased when it isn't done
near the actual place the new reference is used. So using kref_get right
before the place which requires the reference and in the same function
helps to avoid accidental problems caused by incorrect reference counting.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
It is hard to understand why the refcnt is increased when it isn't done
near the actual place the new reference is used. So using kref_get right
before the place which requires the reference and in the same function
helps to avoid accidental problems caused by incorrect reference counting.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
It is hard to understand why the refcnt is increased when it isn't done
near the actual place the new reference is used. So using kref_get right
before the place which requires the reference and in the same function
helps to avoid accidental problems caused by incorrect reference counting.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
It is hard to understand why the refcnt is increased when it isn't done
near the actual place the new reference is used. So using kref_get right
before the place which requires the reference and in the same function
helps to avoid accidental problems caused by incorrect reference counting.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
It is hard to understand why the refcnt is increased when it isn't done
near the actual place the new reference is used. So using kref_get right
before the place which requires the reference and in the same function
helps to avoid accidental problems caused by incorrect reference counting.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
It is hard to understand why the refcnt is increased when it isn't done
near the actual place the new reference is used. So using kref_get right
before the place which requires the reference and in the same function
helps to avoid accidental problems caused by incorrect reference counting.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
It is hard to understand why the refcnt is increased when it isn't done
near the actual place the new reference is used. So using kref_get right
before the place which requires the reference and in the same function
helps to avoid accidental problems caused by incorrect reference counting.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
It is hard to understand why the refcnt is increased when it isn't done
near the actual place the new reference is used. So using kref_get right
before the place which requires the reference and in the same function
helps to avoid accidental problems caused by incorrect reference counting.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Set the netnsof flag on the family structure, indicating it can
be used with different network name spaces.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Dump the list of bridge loop avoidance backbones via the netlink socket.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
The bridge loop avoidange is the main information for the debugging of of
bridge loop detection problems. It is therefore necessary when comparing
the bla claim tables.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Dump the list of bridge loop avoidance claims via the netlink socket.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[sven.eckelmann@open-mesh.com: add policy for attributes, fix includes, fix
soft_iface reference leak]
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
[sw@simonwunderlich.de: fix kerneldoc, fix error reporting]
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Dump the list of gateways via the netlink socket.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[sven.eckelmann@open-mesh.com: integrate in batadv_algo_ops]
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Add BATADV_CMD_GET_GATEWAYS commands, using handlers bat_gw_dump in
batadv_algo_ops. Will always return -EOPNOTSUPP for now, as no
implementations exist yet.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Dump the algo V originators and neighbours.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[sven@narfation.org: Fix includes, fix algo_ops integration]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Add BATADV_CMD_GET_ORIGINATORS and BATADV_CMD_GET_NEIGHBORS commands,
using handlers bat_orig_dump and bat_neigh_dump in batadv_algo_ops. Will
always return -EOPNOTSUPP for now, as no implementations exist yet.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[sven@narfation.org: Rewrite based on new algo_ops structures]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
The TTVN is the main information for the debugging of translation table
problems. It is therefore necessary when comparing the global translation
tables.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
This adds the commands BATADV_CMD_GET_TRANSTABLE_LOCAL and
BATADV_CMD_GET_TRANSTABLE_GLOBAL, which correspond to the transtable_local
and transtable_global debugfs files.
The batadv_tt_client_flags enum is moved to the UAPI to expose it as part
of the netlink API.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[sven.eckelmann@open-mesh.com: add policy for attributes, fix includes]
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
[sw@simonwunderlich.de: fix VID attributes content]
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
BATADV_CMD_GET_HARDIFS will return the list of hardifs (including index,
name and MAC address) of all hardifs for a given softif.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[sven.eckelmann@open-mesh.com: Reduce the number of changes to
BATADV_CMD_GET_HARDIFS, add policy for attributes]
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
BATADV_CMD_GET_ROUTING_ALGOS is used to get the list of supported routing
algorithms.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[sven.eckelmann@open-mesh.com: Reduce the number of changes to
BATADV_CMD_GET_ROUTING_ALGOS, fix includes]
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Debugfs is not netns aware. It thus has problems when the same
interface name exists in multiple network name spaces.
Work around this by not creating entries for interfaces in name spaces
other than the default name space. This means meshes in network
namespaces cannot be managed via debugfs, but there will soon be a
netlink interface which is netns aware.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
batman-adv tries to prevent the user from placing a batX soft
interface into another batman mesh as a hard interface. It does this
by walking up the devices list of parents and ensures they are all
none batX interfaces. iflink can point to an interface in a different
namespace, so also retrieve the parents name space when finding the
parent and use it when doing the comparison.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[sven@narfation.org: Fix alignments, simplify parent netns retrieval]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
The debug messages of _batadv_update_route were printed before the actual
route change is done. At this point it is not really known which
curr_router will be replaced. Thus the messages could print the wrong
operation.
Printing the debug messages after the operation was done avoids this
problem.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
This silences the following coccinelle warning:
"WARNING: sum of probable bitmasks, consider |"
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The function batadv_send_skb_unicast is not acquiring a reference for an
orig_node nor removing it from any datastructure. It still reduces the
reference counter for an object which is still in the hands of the caller.
This is confusing and can lead in the future to problems in the reference
handling of the caller function.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The translation table (global, local) is usually the part of batman-adv
which has the most dynamical allocated objects. Most of them
(tt_local_entry, tt_global_entry, tt_orig_list_entry, tt_change_node,
tt_req_node, tt_roam_node) are equally sized. So it makes sense to have
them allocated from a kmem_cache for each type.
This approach allowed a small wireless router (TP-Link TL-841NDv8; SLUB
allocator) to store 34% more translation table entries compared to the
current implementation.
[1] https://open-mesh.org/projects/batman-adv/wiki/Kmalloc-kmem-cache-tests
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
This patch abstracts the forward packet creation into the new function
batadv_forw_packet_alloc().
The queue counting and interface reference counters are now handled
internally within batadv_forw_packet_alloc() and its
batadv_forw_packet_free() counterpart. This should reduce the risk of
having reference/queue counting bugs again and should increase
code readibility.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
net/batman-adv/bridge_loop_avoidance.c:1105:9-10: WARNING: return of 0/1 in function 'batadv_bla_process_claim' with return type bool
Return statements in functions returning bool should use
true/false instead of 1/0.
Generated by: scripts/coccinelle/misc/boolreturn.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The difference between tq1 and tq2 are calculated the same way in two
separate functions.
This patch moves the common code to a separate function
'batadv_iv_ogm_neigh_diff' which handles everything necessary. The other
two functions can then handle errors and use the difference directly.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
[sven@narfation.org: rebased on current version, initialize return variable
in batadv_iv_ogm_neigh_diff, add kerneldoc, convert to bool return type]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Now that the GW-mode code is algorithm specific, batman-adv expects the
routing algorithm to implement some APIs to make it work.
However, such APIs are not mandatory, therefore we might have algorithms
not providing them. In this case all the sysfs knobs related to GW-mode
should be deactivated to make sure that settings injected by the user
for this feature are rejected.
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Since the GW selection logic has been made routing protocol specific
it is now possible for B.A.T.M.A.N V to have its own mechanism by
providing the API implementation.
Implement the GW specific API in the B.A.T.M.A.N. V protocol in
order to provide a working GW selection mechanism.
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Each routing protocol may have its own specific logic about
gateway election which is potentially based on the metric being
used.
Create two GW specific API functions and move the current election
logic in the B.A.T.M.A.N. IV specific code.
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The B.A.T.M.A.N. V algorithm uses a different metric compared to its
predecessor and for this reason the logic used to compute the best
Gateway is also changed. This means that the GW selection class
fed to this logic has a semantics that depends on the algorithm being
used.
Make the parsing and printing routine of the GW selection class
routing algorithm specific. Each algorithm can now parse (and print)
this value independently.
If no API is provided by any algorithm, the default is to use the
current mechanism of considering such value like an integer between
1 and 255.
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The kobject_put is only removing the sysfs entry and corresponding entries
when its reference counter becomes zero. This tends to lead to collisions
when a device is moved between two different network namespaces because
some of the sysfs files have to be removed first and then added again to
the already moved sysfs entry.
WARNING: CPU: 0 PID: 290 at lib/kobject.c:240 kobject_add_internal+0x5ec/0x8a0
kobject_add_internal failed for batman_adv with -EEXIST, don't try to register things with the same name in the same directory.
But the caller of kobject_put can already remove the sysfs entry before it
does the kobject_put. This removal is done even when the reference counter
is not yet zero and thus avoids the problem.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Postponing the removal of the interface breaks the expected behavior of
NETDEV_UNREGISTER and NETDEV_PRE_TYPE_CHANGE. This is especially
problematic when an interface is removed and added in quick succession.
This reverts commit 5bc44dc845 ("batman-adv: postpone sysfs removal when
unregistering").
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The legacy sysfs interface to modify interfaces belonging to batman-adv
is run inside a region holding s_lock. And to add a net_device, it has
to also get the rtnl_lock. This is exactly the other way around than in
other virtual net_devices and conflicts with netdevice notifier which
executes inside rtnl_lock.
The inverted lock situation is currently solved by executing the removal
of netdevices via workqueue. The workqueue isn't executed inside
rtnl_lock and thus can independently get the s_lock and the rtnl_lock.
But this workaround fails when the netdevice notifier creates events in
quick succession and the earlier triggered removal of a net_device isn't
processed in the workqueue before the adding of the new netdevice (with
same name) event is issued.
Instead the legacy sysfs interface store events have to be enqueued in
a workqueue to loose the s_lock. The worker is then free to get the
required locks and the deadlock is avoided.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The batman-adv module can automatically be loaded when operations over the
rtnl link are triggered. This requires only the correct rtnl link name in
the module header.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Some operations in batadv_algo_ops are optional and marked as such in the
kerneldoc. But some of them miss the "(optional)" in their kerneldoc. These
have to also be marked to give an implementor of an algorithm the correct
background information without looking in the code calling these function
pointers.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Speedy join only works when the received packet is either broadcast or an
4addr unicast packet. Thus packets converted from broadcast to unicast via
the gateway handling code have to be converted to 4addr packets to allow
the receiving gateway server to add the sender address as temporary entry
to the translation table.
Not doing it will make the batman-adv gateway server drop the DHCP response
in many situations because it doesn't yet have the TT entry for the
destination of the DHCP response.
Fixes: 371351731e ("batman-adv: change interface_rx to get orig node")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The orig_ifinfo reference counter for last_bonding_candidate in
batadv_orig_node has to be reduced when an originator node is released.
Otherwise the orig_ifinfo is leaked and the reference counter the netdevice
is not reduced correctly.
Fixes: f3b3d90189 ("batman-adv: add bonding again")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The replacement of last_bonding_candidate in batadv_orig_node has to be an
atomic operation. Otherwise it is possible that the reference counter of a
batadv_orig_ifinfo is reduced which was no longer the
last_bonding_candidate when the new candidate is added. This can either
lead to an invalid memory access or to reference leaks which make it
impossible to an interface which was added to batman-adv.
Fixes: f3b3d90189 ("batman-adv: add bonding again")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The pointer batadv_bla_claim::backbone_gw can be changed at any time.
Therefore, access to it must be protected to ensure that two function
accessing the same backbone_gw are actually accessing the same. This is
especially important when the crc_lock is used or when the backbone_gw of a
claim is exchanged.
Not doing so leads to invalid memory access and/or reference leaks.
Fixes: 23721387c4 ("batman-adv: add basic bridge loop avoidance code")
Fixes: 5a1dd8a477 ("batman-adv: lock crc access in bridge loop avoidance")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
batadv_orig_node_new uses batadv_orig_node_vlan_new to allocate a new
batadv_orig_node_vlan and add it to batadv_orig_node::vlan_list. References
to this list have also to be cleaned when the batadv_orig_node is removed.
Fixes: 7ea7b4a142 ("batman-adv: make the TT CRC logic VLAN specific")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
vlan_insert_tag can return NULL on errors. The distributed arp table code
therefore has to check the return value of vlan_insert_tag for NULL before
it can safely operate on this pointer.
Fixes: be1db4f661 ("batman-adv: make the Distributed ARP Table vlan aware")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
vlan_insert_tag can return NULL on errors. The bridge loop avoidance code
therefore has to check the return value of vlan_insert_tag for NULL before
it can safely operate on this pointer.
Fixes: 23721387c4 ("batman-adv: add basic bridge loop avoidance code")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
- Cleanup work by Markus Pargmann and Sven Eckelmann (six patches)
- Initial Netlink support by Matthias Schiffer (two patches)
- Throughput Meter implementation by Antonio Quartulli, a kernel-space
traffic generator to estimate link speeds. This feature is useful on
low-end WiFi APs where running iperf or netperf from userspace
gives wrong results due to heavy userspace/kernelspace overhead.
(two patches)
- API clean-up work by Antonio Quartulli (one patch)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PFHu
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20160704' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature patchset includes the following changes:
- Cleanup work by Markus Pargmann and Sven Eckelmann (six patches)
- Initial Netlink support by Matthias Schiffer (two patches)
- Throughput Meter implementation by Antonio Quartulli, a kernel-space
traffic generator to estimate link speeds. This feature is useful on
low-end WiFi APs where running iperf or netperf from userspace
gives wrong results due to heavy userspace/kernelspace overhead.
(two patches)
- API clean-up work by Antonio Quartulli (one patch)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The routing API data structure contains several function
pointers that can easily be grouped together based on the
component they work with.
Split the API in subobjects in order to improve definition readability.
At the same time, remove the "bat_" prefix from the API object and
its fields names. These are batman-adv private structs and there is no
need to always prepend such prefix, which only makes function invocations
much much longer.
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Reviewed-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The throughput meter module is a simple, kernel-space replacement for
throughtput measurements tool like iperf and netperf. It is intended to
approximate TCP behaviour.
It is invoked through batctl: the protocol is connection oriented, with
cumulative acknowledgment and a dynamic-size sliding window.
The test *can* be interrupted by batctl. A receiver side timeout avoids
unlimited waitings for sender packets: after one second of inactivity, the
receiver abort the ongoing test.
Based on a prototype from Edo Monticelli <montik@autistici.org>
Signed-off-by: Antonio Quartulli <antonio.quartulli@open-mesh.com>
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Return the proper netdev TX status along the TX path so that the tp_meter
can understand when the queue is full and should stop sending packets.
Signed-off-by: Antonio Quartulli <antonio.quartulli@open-mesh.com>
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
BATADV_CMD_GET_MESH_INFO is used to query basic information about a
batman-adv softif (name, index and MAC address for both the softif and
the primary hardif; routing algorithm; batman-adv version).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[sven.eckelmann@open-mesh.com: Reduce the number of changes to
BATADV_CMD_GET_MESH_INFO, add missing kerneldoc, add policy for attributes]
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
debugfs is currently severely broken virtually everywhere in the kernel
where files are dynamically added and removed (see
http://lkml.iu.edu/hypermail/linux/kernel/1506.1/02196.html for some
details). In addition to that, debugfs is not namespace-aware.
Instead of adding new debugfs entries, the whole infrastructure should be
moved to netlink. This will fix the long standing problem of large buffers
for debug tables and hard to parse text files.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[sven.eckelmann@open-mesh.com: Strip down patch to only add genl family,
add missing kerneldoc]
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
- two patches with minimal clean up work by Antonio Quartulli and
Simon Wunderlich
- eight patches of B.A.T.M.A.N. V, API and documentation clean
up work, by Antonio Quartulli and Marek Lindner
- Andrew Lunn fixed the skb priority adoption when forwarding
fragmented packets (two patches)
- Multicast optimization support is now enabled for bridges which
comes with some protocol updates, by Linus Luessing
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=js/J
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20160701' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature patchset includes the following changes:
- two patches with minimal clean up work by Antonio Quartulli and
Simon Wunderlich
- eight patches of B.A.T.M.A.N. V, API and documentation clean
up work, by Antonio Quartulli and Marek Lindner
- Andrew Lunn fixed the skb priority adoption when forwarding
fragmented packets (two patches)
- Multicast optimization support is now enabled for bridges which
comes with some protocol updates, by Linus Luessing
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
The bat_algo.h had some functions declared which were not part of the
bat_algo.c file. These are instead stored in bat_v.c and bat_iv_ogm.c. The
declaration should therefore be also in bat_v.h and bat_iv_ogm,h to make
them easier to find.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
This patch adds a debugfs table with originators and their according
multicast flags to help users figure out why multicast optimizations
might be enabled or disabled for them.
Tested-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
There are several places in batman-adv which provide logging related
functions. These should be grouped together in the log.* files to make them
easier to find.
Reported-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
With this patch changes relevant to a node's own multicast flags are
printed to the 'mcast' log level.
Tested-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The bat_algo functionality in main.c is mostly unrelated to the rest of the
content. It still takes up a large portion of this source file (~15%, 103
lines). Moving it to a separate file makes it better visible as a main
component of the batman-adv implementation and hides it less in the other
helper functions in main.c.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
With this patch we are finally able to support multicast optimizations
in bridged setups, too. So far, if a bridge was added on top of a
soft-interface (e.g. bat0) the batman-adv multicast optimizations
needed to be disabled to avoid packetloss.
Current Linux bridge implementations and API can now provide us
with the so far missing information about interested but "remote"
multicast receivers behind bridge ports.
The Linux bridge performs the detection of remote participants
interested in multicast packets with its own and mature so
called IGMP and MLD snooping code and stores that in its
database. With the new API provided by the bridge batman-adv can
now simply hook into this database.
We then reliably announce the gathered multicast listeners to
other nodes through the batman-adv translation table.
Additionally, the Linux bridge provides us with the information about
whether an IGMP/MLD querier exists. If there is none then we need to
disable multicast optimizations as we cannot learn about multicast
listeners on external, bridged-in host then.
Tested-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The tvlv functionality in main.c is mostly unrelated to the rest of the
content. It still takes up a large portion of this source file (~45%, 588
lines). Moving it to a separate file makes it better visible as a main
component of the batman-adv implementation and hides it less in the other
helper functions in main.c
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
[sven@narfation.org: fix conflicts with current version, fix includes,
rewrote commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
With this patch IGMP or MLD reports are always flooded. This is
necessary for the upcoming bridge integration to function without
multicast packet loss.
With the report handling so far bridges might miss interested multicast
listeners, leading to wrongly excluding ports from multicast packet
forwarding.
Currently we are treating IGMP/MLD reports, the messages bridges use to
learn about interested multicast listeners, just as any other multicast
packet: We try to send them to nodes matching its multicast destination.
Unfortunately, the destination address of reports of the older
IGMPv2/MLDv1 protocol families do not strictly adhere to their own
protocol: More precisely, the interested receiver, an IGMPv2 or MLDv1
querier, itself usually does not listen to the multicast destination
address of any reports.
Therefore with this patch we are simply excluding IGMP/MLD reports from
the multicast forwarding code path and keep flooding them. By that
any bridge receives them and can properly learn about listeners.
To avoid compatibility issues with older nodes not yet implementing this
report handling, we need to force them to flood reports: We do this by
bumping the multicast TVLV version to 2, effectively disabling their
multicast optimization.
Tested-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
It is easier to detect if a include is already there for a used
functionality when the includes are ordered. Using an alphabetic order
together with the grouping in commit 1e2c2a4fe4 ("batman-adv: Add
required includes to all files") makes includes better manageable.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Unfragmented frames which traverse a node have their skb->priority set
by looking at the IP ToS byte, or the 802.1p header. However for
fragments this is not possible, only one of the fragments will contain
the headers. Instead, place the priority into the fragment header and
on receiving a fragment, use this information to set the skb->priority
for when the fragment is forwarded.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
main.h includes statements which (re)define preprocessor variables which
influence the compiled code. This makes it necessary to include it in all
files. For example, it redefines pr_fmt used to the module as prefix for
each pr_* message.
Reported-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
BATMAN will set the skb->priority based on the IP precedence or 802.1q
tag. However, if it needs to fragment the frame, it currently leaves
the fragment skb with the default priority and actually overwrites the
priority in the unfragmented frame. Fix this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The ELP interval and throughput override interface settings are initialized
with default settings on every time an interface is added to a mesh.
This patch prevents this behavior by moving the configuration init to the
interface detection routine which runs only once per interface.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
[a@unstable.cc: move initialization to batadv_v_hardif_init]
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>