CCK/OFDM noise immunilty values are always reset to defaults
during bgscan. This could affect the link quality and
performance when the STA is associated in a noisy channel.
So do not override the learned values across the scanning.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
removed a function declaration, removed a variable, renamed a variable
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of keeping track of wraparound, clear the counters on every
access and keep separate deltas for ANI and later survey use.
Also moves the function for calculating the 'listen time' for ANI
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ANI state is kept per channel, so instead of keeping an array of ANI states
with an arbitrary size of 255, move the ANI state into the channel struct.
Move some config settings that are not per-channel out of
the per-channel struct to save some memory.
With those changes, ath9k_ani_restart_old and ath9k_ani_restart_new can
be merged into a single function.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The cycle counters are used by ANI to determine the amount of time that the
radio spent not receiving or transmitting. They're also used for debugging
purposes if the baseband watchdog on AR9003 detects a lockup.
In the future, we want to use these counters to determine the medium utilization
and export this information via survey. For that, we need to make sure that
the counter is only accessed from one place, which also ensures that
wraparounds won't occur at inconvenient points in time.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for ANI for AR9003. The implementation for
ANI for AR9003 is slightly different than the one used for
the older chipset families. It can technically be used for
the older families as well but this is not yet fully tested
so we only enable the new ANI for the AR5008, AR9001 and AR9002
families with a module parameter, force_new_ani.
The old ANI implementation is left intact.
Details of the new ANI implemention:
* ANI adjustment logic is now table driven so that each ANI level
setting is parameterized. This makes adjustments much more
deterministic than the old procedure based logic and allows
adjustments to be made incrementally to several parameters per
level.
* ANI register settings are now relative to INI values; so ANI
param zero level == INI value. Appropriate floor and ceiling
values are obeyed when adjustments are combined with INI values.
* ANI processing is done once per second rather that every 100ms.
The poll interval is now a set upon hardware initialization and
can be picked up by the core driver.
* OFDM error and CCK error processing are made in a round robin
fashion rather than allowing all OFDM adjustments to be made
before CCK adjustments.
* ANI adjusts MRC CCK off in the presence of high CCK errors
* When adjusting spur immunity (SI) and OFDM weak signal detection,
ANI now sets register values for the extension channel too
* When adjusting FIR step (ST), ANI now sets register for FIR step
low too
* FIR step adjustments now allow for an extra level of immunity for
extremely noisy environments
* The old Noise immunity setting (NI), which changes coarse low, size
desired, etc have been removed. Changing these settings could affect
up RIFS RX as well.
* CCK weak signal adjustment is no longer used
* ANI no longer enables phy error interrupts; in all cases phy hw
counting registers are used instead
* The phy error count (overflow) interrupts are also no longer used
for ANI adjustments. All ANI adjustments are made via the polling
routine and no adjustments are possible in the ISR context anymore
* A history settings buffer is now correctly used for each channel;
channel settings are initialized with the defaults but later
changes are restored when returning back to that channel
* When scanning, ANI is disabled settings are returned to (INI) defaults.
* OFDM phy error thresholds are now 400 & 1000 (errors/second units) for
low/high water marks, providing increased stability/hysteresis when
changing levels.
* Similarly CCK phy error thresholds are now 300 & 600 (errors/second)
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AR9003 hardware family will use a slightly modified ANI
implementation which has not yet been tested on the other hardware
families. To allow for this new ANI implementation a few ANI
calls need to be abstracted away. This patch just allows for
each hardware family to declare their own ANI ops and annotates
the current ANI implementation as old.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no reason to disable the PHY Error / MIB counters
when the module is being unloaded.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Other than ns_avgbrssi (Average beacon rssi) no data of
ath9k_node_stats is being used anywhere. Nuke this structure
and move its only useful member to ar5416Anistate. Also cleanup
this redundant data in ath_softc.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the beacon rssi that LPF gives is divided and rounded
up by ATH_RSSI_EP_MULTIPLIER twice. This will leave the incorrect rssi
in ANI. Having correct rssi in ANI fixes the connection stability at
< 30dB rssi range. This patch removes the unncessary computation of average
rssi over already valid average rssi. Also removes the redundant macros to
find average rssi.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PHY counters are available in all chipsets supported
by ath9k. Remove the check.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During initialization ath9k tends to use "attach" to when we
initialize hardware due to the fact we used to attach a "HAL".
The notion of a HAL is long gone, so lets just be clear on what
we are doing.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan