Reported-by: Chris Clayton <chris2553@googlemail.com>
Tested-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Hangcheck and error recovery is only used by GEM.
Reported-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
945 class hardware has an interesting quirk in which the vblank
interrupt is not raised if the CPU is in a low power state. (We also
suspect that the memory bus is clocked to the CPU/c-state and not the
GPU so there are secondary starvation issues.) In order to prevent the
most obvious issue of the low of the vblank interrupt (stuttering
compositing that only updates when the mouse is moving) is to install a
PM QoS request to prevent low c-states whilst the GPU is active.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Whilst we had no older batches on the active list, everything was fine.
However, if the GPU is free running and the requests are only being
reaped by the periodic retirer, than the current seqno may not be at the
start of the list. In this case we need to select the first batch after
the last seqno written by the gpu and not inclusive of the seqno.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
FDI and the transcoders can fail for various reasons, so detect those
conditions and report on them.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Add an interrupt handler for switching graphics frequencies and handling
PM interrupts. This should allow for increased performance when busy
and lower power consumption when idle.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
v2: Change IS_IRONLAKE to IS_GEN5 to adapt to 2.6.37
This patch adds new functions for use by the drm core:
.get_vblank_timestamp() provides a precise timestamp
for the end of the most recent (or current) vblank
interval of a given crtc, as needed for the DRI2
implementation of the OML_sync_control extension.
It is a thin wrapper around the drm function
drm_calc_vbltimestamp_from_scanoutpos() which does
almost all the work.
.get_scanout_position() provides the current horizontal
and vertical video scanout position and "in vblank"
status of a given crtc, as needed by the drm for use by
drm_calc_vbltimestamp_from_scanoutpos().
The patch modifies the pageflip completion routine
to use these precise vblank timestamps as the timestamps
for pageflip completion events.
This code has been only tested on a HP-Mini Netbook with
Atom processor and Intel 945GME gpu. The codepath for
(IS_G4X(dev) || IS_GEN5(dev) || IS_GEN6(dev)) gpu's
has not been tested so far due to lack of hardware.
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Restore PIPE_CONTROL once again just for Ironlake, as it appears that
MI_USER_INTERRUPT does not have the same coherency guarantees, that is
on Ironlake the interrupt following a GPU write is not guaranteed to
arrive after the write is coherent from the CPU, as it does on the
other generations.
Reported-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Reported-by: Shuang He <shuang.he@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=32402
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
In order to enforce the correct memory barriers for irq get/put, we need
to perform the actual counting using atomic operations.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The workaround is hideous and we are using the STORE_DWORD on all other
generations on all other rings, so use for the gen5 render ring as
well.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The bulk of the change is to convert the growing list of rings into an
array so that the relationship between the rings and the semaphore sync
registers can be easily computed.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Having seen the effects of erroneous fencing on the batchbuffer, a
useful sanity check is to record the fence registers at the time of an
error.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
When trying to diagnose mysterious errors on resume, capture the
display register contents as well.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The pinned buffers are useful for diagnosing errors in setting up state
for the chipset, which may not necessarily be 'active' at the time of
the error, e.g. the cursor buffer object.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We only ever used the PRB0, neglecting the secondary ring buffers, and
now with the advent of multiple engines with separate ring buffers we
need to excise the anachronisms from our code (and be explicit about
which ring we mean where). This is doubly important in light of the
FORCEWAKE required to read ring buffer registers on SandyBridge.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This holds error state from the main graphics arbiter mainly involving
the DMA engine and address translation.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Currently, we believe the GPU is idle if just the RENDER ring is idle.
This is obviously wrong if we only using either the BLT or the BSD
rings and so masking genuine hangs.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Preparing the ringbuffer for adding new commands can fail (a timeout
whilst waiting for the GPU to catch up and free some space). So check
for any potential error before overwriting HEAD with new commands, and
propagate that error back to the user where possible.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The ringbuffer keeps a pointer to the parent device, so we can use that
instead of passing around the pointer on the stack.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (476 commits)
vmwgfx: Implement a proper GMR eviction mechanism
drm/radeon/kms: fix r6xx/7xx 1D tiling CS checker v2
drm/radeon/kms: properly compute group_size on 6xx/7xx
drm/radeon/kms: fix 2D tile height alignment in the r600 CS checker
drm/radeon/kms/evergreen: set the clear state to the blit state
drm/radeon/kms: don't poll dac load detect.
gpu: Add Intel GMA500(Poulsbo) Stub Driver
drm/radeon/kms: MC vram map needs to be >= pci aperture size
drm/radeon/kms: implement display watermark support for evergreen
drm/radeon/kms/evergreen: add some additional safe regs v2
drm/radeon/r600: fix tiling issues in CS checker.
drm/i915: Move gpu_write_list to per-ring
drm/i915: Invalidate the to-ring, flush the old-ring when updating domains
drm/i915/ringbuffer: Write the value passed in to the tail register
agp/intel: Restore valid PTE bit for Sandybridge after bdd3072
drm/i915: Fix flushing regression from 9af90d19f
drm/i915/sdvo: Remove unused encoding member
i915: enable AVI infoframe for intel_hdmi.c [v4]
drm/i915: Fix current fb blocking for page flip
drm/i915: IS_IRONLAKE is synonymous with gen == 5
...
Fix up conflicts in
- drivers/gpu/drm/i915/{i915_gem.c, i915/intel_overlay.c}: due to the
new simplified stack-based kmap_atomic() interface
- drivers/gpu/drm/vmwgfx/vmwgfx_drv.c: added .llseek entry due to BKL
removal cleanups.
Keep the current interface but ignore the KM_type and use a stack based
approach.
The advantage is that we get rid of crappy code like:
#define __KM_PTE \
(in_nmi() ? KM_NMI_PTE : \
in_irq() ? KM_IRQ_PTE : \
KM_PTE0)
and in general can stop worrying about what context we're in and what kmap
slots might be appropriate for that.
The downside is that FRV kmap_atomic() gets more expensive.
For now we use a CPP trick suggested by Andrew:
#define kmap_atomic(page, args...) __kmap_atomic(page)
to avoid having to touch all kmap_atomic() users in a single patch.
[ not compiled on:
- mn10300: the arch doesn't actually build with highmem to begin with ]
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix up drivers/gpu/drm/i915/intel_overlay.c]
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Miller <davem@davemloft.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Based on an original patch by Zhenyu Wang, this initializes the BLT ring for
SandyBridge and enables support for user execbuffers.
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
To handle retirements, we need per-ring tracking of active objects.
To handle evictions, we need global tracking of active objects.
As we enable more rings, rebuilding the global list from the individual
per-ring lists quickly grows tiresome and overly complicated. Tracking the
active objects in two lists is the lesser of two evils.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
On Sandybridge, the bit definition for hotplug on SDE has changed, so
update the code to new definition.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30378
Cc: stable@kernel.org
Signed-off-by: Yuanhan Liu <yuanhan.liu@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Owain Ainsworth reported an issue between the interaction of the
hangcheck and userspace immediately (and permanently) falling back to
s/w rasterisation. In order to break the mutex and begin resetting the
GPU, we must abort the current operation (usually within the wait) and
climb sufficiently far back up the call chain to drop the mutex. In his
implementation, Owain has a loop within the ioctl handler to detect the
hang and then sleep until the error handler has run. I've chosen to
return to userspace and report an EAGAIN which should trigger the
userspace ioctl handler to repeat the call (simply because it felt less
invasive...). Before hitting a wedged GPU, we then wait upon completion
of the error handler.
Reported-by: Owain G. Ainsworth <zerooa@googlemail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Avoid cause latencies in other clients by not taking the global struct
mutex and moving the per-client request manipulation a local per-client
mutex. For example, this allows a compositor to schedule a page-flip
(through X) whilst an OpenGL application is monopolising the GPU.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This ring buffer is used for video decoding/encoding on Sandybridge.
Signed-off-by: Xiang, Haihao <haihao.xiang@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Previously we only tidied up the active bo lists for chipsets were we
would attempt to reset the GPU. However, this action is necessary for
the system to continue and reclaim the dead bo for all chipsets.
Pointed out, in passing, by Owain Ainsworth.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Ironlake's graphics reset register has to be accessed via the MCHBAR,
rather than via PCI config space, which requires some refactoring.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The graphics domains are listed as GRDOM in the documentation, and the
GDRST PCI config register (0xc0) is only valid on I965 and GM45. Newer
chips (like Sandy Bridge) have a different GDRST.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
By reducing the hangcheck frequency we check less often, conserving
resources, and still detect a lock up quickly. On a fast machine with a
slow GPU (like a Core2 paired with a 945G) it is easy for the hangcheck to
misfire as we check too fast.
Also once hung and if we fail to completely reset the chip, we have a
nasty habit of proclaming a hang many times a second and generating a
strobe-like display.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The purpose is to make the code much easier to read and therefore reduce
the possibility for bugs.
A side effect is that it also makes it much easier for the compiler,
reducing the object size by 4k -- from just a few functions!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[Patch is slightly larger than is strictly necessary to fixup
surrounding checkpatch.pl errors.]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If we are busy, then we may have woken up the wait_request handler but
not yet serviced it before the hang check fires. So in hang check,
double check that the i915_gem_do_wait_request() is still pending the
wake-up before declaring all hope lost.
Fixes regression with e78d73b16b.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30073
Reported-and-tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The GPU records whether it is currently waiting for a completion of a
WAIT_FOR_EVENT in the RB_WAIT bit in the ringbuffer control registers.
On third generation chipsets and later, a write of 1 to this bit breaks
the hang and returns the GPU to arbitration, i.e. the GPU should
continue executing the reminder of the batchbuffer and return to normal
operations.
By adding this to hangcheck we can avoid a full GPU reset under these
conditions.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Alexander reported that the compilation of intel_overlay.c was failing
due to an inclusion that was only valid with CONFIG_DEBUG_FS. As the
whole error reporting is only useful with debugfs enabled, remove all
the redundant error state collection code when compiling without
CONFIG_DEBUG_FS.
Reported-by: Alexander Lam <lambchop468@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Fix a minor confusion between intel_page_flip_finish(pipe) and
intel_page_flip_finish_plane(plane) -- should have no effect as
currently we map pipe 0 to plane 0 (and pipe 1 to plane 1).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
It's part of the generic Intel driver infrastructure so rename it in
prepreparation for using it for VBT.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
When we miss the flip prepare interrupt, we never get into the
software state needed to restart userspace, resulting in a freeze of a
full-screen OpenGL application (such as a compositor).
Work around this by checking DSPxSURF/DSPxBASE to see if the page flip
has actually happened. If it has, do the work we would have done when
the flip prepare interrupt comes in.
Also, add debugfs information to tell us what's going on (based on the
patch from Chris Wilson attached to bugs.fdo bug #29798).
Signed-off-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This one is missed in last pipe control fix for sandybridge,
that really unmask interrupt bit for notify in render engine IMR.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
If our watchdog fires and we see that the GPU is idle, but that we
are still waiting on an interrupt, forcibly wake-up the waiter.
i915_do_wait_request() should not be racy, yet there are persistent
reports that 945GM hangs whilst the GPU is idle. This implies that the
hardware is not quite as coherent as the documentation claims - a write
followed by a flush is supposed to be coherent in main memory before the
flush is retired and the irq is emitted. This seems to be a sensible and
elegant guard to force the wait to timeout.
v2: Daniel Vetter pointed out that a warning would be useful to explain
why the machine appeared to stall.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Directly read the GTT mapping for the contents of the batch buffers
rather than relying on possibly stale CPU caches. Also for completeness
scan the flushing/inactive lists for the current buffers - we are
collecting error state after all.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
v2: Add the interrupt status and address.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
References:
Bug 26691 - Spurious hangcheck whilst executing a long shader over a
large vertex buffer
https://bugs.freedesktop.org/show_bug.cgi?id=26691
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Having two sets has made me think I caught a bug more than once now.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Commit 7a772c492f has two bugs which
made the hotplug problems on my laptop worse instead of better.
First, it did not, in fact, disable the CRT plug interrupt -- it
disabled all the other hotplug interrupts. It seems rather doubtful
that that bit of the patch fixed anything, so let's just remove it.
(If you want to add it back, you probably meant ~CRT_HOTPLUG_INT_EN.)
Second, on at least my GM45, setting CRT_HOTPLUG_ACTIVATION_PERIOD_64
and CRT_HOTPLUG_VOLTAGE_COMPARE_50 (when they were previously unset)
causes a hotplug interrupt about three seconds later. The old code
never restored PORT_HOTPLUG_EN so this could only happen once, but
they new code restores those registers. So just set those bits when
we set up the interrupt in the first place.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Signed-off-by: Eric Anholt <eric@anholt.net>
Gen3 chips have slightly different flip commands, and also contain a bit
that indicates whether a "flip pending" interrupt means the flip has
been queued or has been completed.
So implement support for the gen3 flip command, and make sure we use the
flip pending interrupt correctly depending on the value of ECOSKPD bit
0.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Unmask, then enable interrupts, then enable interrupt sources; matches
PCH ordering. The old way (sources, enable, unmask) gives a window
during which interrupt conditions would appear in ISR but would never
reach IIR and thus never raise an IRQ. Since interrupts only trigger
on rising edges in ISR, this would lead to conditions where (for
example) output hotplugging would never fire an interrupt because it
was already stuck on in ISR.
Also, since we know IIR and PIPExSTAT have been cleared during
irq_preinstall, don't clear them again during irq_postinstall, nothing
good can come of that.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Only report an error if the GPU has actually detected one, otherwise we
are just hung.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add power monitoring support to the i915 driver for use by the IPS
driver. Export the available power info to the IPS driver through a few
new inter-driver hooks. When used together, the IPS driver and this
patch can significantly increase graphics performance on Ironlake class
chips.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: Fixed 32-bit compile. stupid obfuscating div_u64()]
Signed-off-by: Eric Anholt <eric@anholt.net>
The BSD (bit stream decoder) ring is used for accessing the BSD engine
which decodes video bitstream for H.264 and VC1 on G45+. It is
asynchronous with the render ring and has access to separate parts of
the GPU from it, though the render cache is coherent between the two.
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Xiang Hai hao <haihao.xiang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The active list and request list move into the ringbuffer structure,
so each can track its active objects in the order they are in that
ring. The flushing list does not, as it doesn't matter which ring
caused data to end up in the render cache. Objects gain a pointer to
the ring they are active on (if any).
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Xiang Hai hao <haihao.xiang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Introduces a more complete intel_ring_buffer structure with callbacks
for setup and management of a particular ringbuffer, and converts the
render ring buffer consumers to use it.
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Signed-off-by: Xiang Hai hao <haihao.xiang@intel.com>
[anholt: Fixed up whitespace fail and rebased against prep patches]
Signed-off-by: Eric Anholt <eric@anholt.net>
This is preparation for supporting multiple ringbuffers on Ironlake.
The non-copy-and-paste changes are:
- de-staticing functions
- I915_GEM_GPU_DOMAINS moving to i915_drv.h to be used by both files.
- i915_gem_add_request had only half its implementation
copy-and-pasted out of the middle of it.
* 'drm-for-2.6.35' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (207 commits)
drm/radeon/kms/pm/r600: select the mid clock mode for single head low profile
drm/radeon: fix power supply kconfig interaction.
drm/radeon/kms: record object that have been list reserved
drm/radeon: AGP memory is only I/O if the aperture can be mapped by the CPU.
drm/radeon/kms: don't default display priority to high on rs4xx
drm/edid: fix typo in 1600x1200@75 mode
drm/nouveau: fix i2c-related init table handlers
drm/nouveau: support init table i2c device identifier 0x81
drm/nouveau: ensure we've parsed i2c table entry for INIT_*I2C* handlers
drm/nouveau: display error message for any failed init table opcode
drm/nouveau: fix init table handlers to return proper error codes
drm/nv50: support fractional feedback divider on newer chips
drm/nv50: fix monitor detection on certain chipsets
drm/nv50: store full dcb i2c entry from vbios
drm/nv50: fix suspend/resume with DP outputs
drm/nv50: output calculated crtc pll when debugging on
drm/nouveau: dump pll limits entries when debugging is on
drm/nouveau: bios parser fixes for eDP boards
drm/nouveau: fix a nouveau_bo dereference after it's been destroyed
drm/nv40: remove some completed ctxprog TODOs
...
* anholt/drm-intel-next: (515 commits)
drm/i915: Fix out of tree builds
drm/i915: move fence lru to struct drm_i915_fence_reg
drm/i915: don't allow tiling changes on pinned buffers v2
drm/i915: Be extra careful about A/D matching for multifunction SDVO
drm/i915: Fix DDC bus selection for multifunction SDVO
drm/i915: cleanup mode setting before unmapping registers
drm/i915: Make fbc control wrapper functions
drm/i915: Wait for the GPU whilst shrinking, if truly desperate.
drm/i915: Use spatio-temporal dithering on PCH
[MTD] Remove zero-length files mtdbdi.c and internal.ho
pata_pcmcia / ide-cs: Fix bad hashes for Transcend and kingston IDs
libata: Fix several inaccuracies in developer's guide
slub: Fix bad boundary check in init_kmem_cache_nodes()
raid6: fix recovery performance regression
KEYS: call_sbin_request_key() must write lock keyrings before modifying them
KEYS: Use RCU dereference wrappers in keyring key type code
KEYS: find_keyring_by_name() can gain access to a freed keyring
ALSA: hda: Fix 0 dB for Packard Bell models using Conexant CX20549 (Venice)
ALSA: hda - Add quirk for Dell Inspiron 19T using a Conexant CX20582
ALSA: take tu->qlock with irqs disabled
...
After thinking it over a lot it made more sense for the core to deal with
the output polling especially so it can notify X.
v2: drop plans for fake connector - per Michel's comments - fix X patch sent to xorg-devel, add intel polled/hpd setting, add initial nouveau polled/hpd settings.
v3: add config lock take inside polling, add intel/nouveau poll init/fini calls
v4: config lock was a bit agressive, only needed around connector list reading.
otherwise it could re-enter.
glisse: discard drm_helper_hpd_irq_event
v3: Reviewed-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
i915_error_object_create() is called from the timer interrupt and hence
can corrupt the KM_USER0 slot. Use KM_IRQ0 instead.
Reported-by: Jaswinder Singh Rajput <jaswinderlinux@gmail.com>
Tested-by: Jaswinder Singh Rajput <jaswinderlinux@gmail.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/radeon/r300.c
The BSD ringbuffer support that is landing in this branch
significantly conflicts with the Ironlake PIPE_CONTROL fix on master,
and requires it to be tested successfully anyway.
Since 965, the hardware has supported the PIPE_CONTROL command, which
provides fine grained GPU cache flushing control. On recent chipsets,
this instruction is required for reliable interrupt and sequence number
reporting in the driver.
So add support for this instruction, including workarounds, on Ironlake
and Sandy Bridge hardware.
https://bugs.freedesktop.org/show_bug.cgi?id=27108
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Luckily the change is quite a little bit less invasive than I've
feared.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* drm-fbdev-cleanup:
drm/fb: remove drm_fb_helper_setcolreg
drm/kms/fb: use slow work mechanism for normal hotplug also.
drm/kms/fb: add polling support for when nothing is connected.
drm/kms/fb: provide a 1024x768 fbcon if no outputs found.
drm/kms/fb: separate fbdev connector list from core drm connectors
drm/kms/fb: move to using fb helper crtc grouping instead of core crtc list
drm/fb: fix fbdev object model + cleanup properly.
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/nouveau/nouveau_drv.h
* 'anholt/drm-intel-next' of /home/airlied/kernel/drm-next: (48 commits)
agp/intel-gtt: kill previous_size assignments
agp/intel-gtt: kill intel_i830_tlbflush
agp/intel: split out gmch/gtt probe, part 1
agp/intel: kill mutli_gmch_chip
agp/intel: uncoditionally reconfigure driver on resume
agp/intel: split out the GTT support
agp/intel: introduce intel-agp.h header file
drm/i915: Don't touch PORT_HOTPLUG_EN in intel_dp_detect()
drm/i915/pch: Use minimal number of FDI lanes (v2)
drm/i915: Add the support of memory self-refresh on Ironlake
drm/i915: Move Pineview CxSR and watermark code into update_wm hook.
drm/i915: Only save/restore FBC on the platform that supports FBC
drm/i915: Fix the incorrect argument for SDVO SET_TV_format command
drm/i915: Add support of SDVO on Ibexpeak PCH
drm/i915: Don't enable pipe/plane/VCO early (wait for DPMS on).
drm/i915: do not read uninitialized ->dev_private
Revert "drm/i915: Use a dmi quirk to skip a broken SDVO TV output."
drm/i915: implement multifunction SDVO device support
drm/i915: remove unused intel_pipe_get_connector()
drm/i915: remove connector object in old output structure
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: Ignore LVDS EDID when it is unavailabe or invalid
drm/i915: Add no_lvds entry for the Clientron U800
drm/i915: Rename many remaining uses of "output" to encoder or connector.
drm/i915: Rename intel_output to intel_encoder.
agp/intel: intel_845_driver is an agp driver!
drm/i915: introduce to_intel_bo helper
drm/i915: Disable FBC on 915GM and 945GM.
OpRegion event on 965G requires legacy BLC event enabled in pipe stat. As LVDS
could be on either pipe now, we should enable BLC event on both pipe. If fail to
do so, we couldn't handle the brightness request triggered from graphics
opregion.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Instead of walking through drm connector_list uses encoder_list
for calling hotplug functions which is consistent with intel display
hotplug reporting.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
a) slow work is always used now for any fbcon hotplug, as its not
a fast task and is more suited to being ran under slow work.
b) attempt to not do any fbdev changes when X is running as we'll
just mess it up. This hooks set_par to hopefully do the changes
once X hands control to fbdev.
This also adds the nouveau/intel hotplug support.
Signed-off-by: Dave Airlie <airlied@redhat.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
The intel_output naming is inherited from the UMS code, which had a
structure of screen -> CRTC -> output. The DRM code has an additional
notion of encoder/connector, so the structure is screen -> CRTC ->
encoder -> connector. This is a useful structure for SDVO encoders
which can support multiple connectors (each of which requires
different programming in the one encoder and could be connected to
different CRTCs), or for DVI-I, where multiple encoders feed into the
connector for whether it's used for digital or analog. Most of our
code is encoder-related, so transition it to talking about encoders
before we start trying to distinguish connectors.
This patch is produced by sed s/intel_output/intel_encoder/ over the
driver.
Signed-off-by: Eric Anholt <eric@anholt.net>
This is a purely cosmetic change to make changes in this area easier.
And hey, it's not only clearer and typechecked, but actually shorter,
too!
[anholt: To clarify, this is a change to let us later make
drm_i915_gem_object subclass drm_gem_object, instead of having
drm_gem_object have a pointer to i915's private data]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
In order to improve our diagnostic capabilities following a GPU hang
and subsequent reset, we need to record the batch buffer that triggered
the error. We assume that the current batch buffer, plus a few details
about what else is on the active list, will be sufficient -- at the very
least an improvement over nothing.
The extra information is stored in /debug/dri/.../i915_error_state
following an error, and may be decoded using
intel_gpu_tools/tools/intel_error_decode.
v2: Avoid excessive work under spinlocks.
v3: Include ringbuffer for later analysis.
v4: Use kunmap correctly and record more buffer state.
v5: Search ringbuffer for current batch buffer
v6: Use a work fn for the impossible IRQ error case.
v7: Avoid non-atomic paths whilst in IRQ context.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
The ironlake render p-state support includes some rather odd variable
names. Clean them up in order to improve the readability of the code.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Ironlake (and 965GM, which this patch doesn't support) supports a
hardware performance and power management feature that allows it to
adjust to changes in GPU load over time with software help. The goal
if this is to maximize performance/power for a given workload.
This patch enables that feature, which is also a requirement for
supporting Intelligent Power Sharing, a feature which allows for
dynamic budgeting of power between the CPU and GPU in Arrandale
platforms.
Tested-by: ykzhao <yakui.zhao@intel.com>
[anholt: Resolved against the irq handler loop removal]
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
On Ironlake plane flip interrupt means flip done event already, the
behavior is not like old chips, and perform like other usual interrupt.
So only need to handle flip done event when receiving that interrupt.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch adds support for page flipping on Ironlake, which uses
different interrupt bits for triggering flip submit IRQs.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: hand-resolved for rebasing off of render power saving patch]
Signed-off-by: Eric Anholt <eric@anholt.net>
Zhenyu noticed that the ironlake vblank enabling patch has one
issue that it will trigger vblank starting from irq postinstall,
this isn't necessary. This patch addresses this issue by only
adding the vblank into DEIER but mask them in DEIMR, so that it
won't trigger vblank interrupt at irq install.
Signed-off-by: Li Peng <peng.li@intel.com>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
so far vblank interrupt on ironlake is disabled, this would cause
bad gfx performance if userspace calls drm_wait_vblank. This patch
enables vblank interrupt on ironlake and follows vblank get/put
model.
Signed-off-by: Li Peng <peng.li@intel.com>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
On Ironlake, there is an interrupt master control bit. With the bit
disabled before clearing IIR, we do not need to handle extra interrupt
in a loop. This patch removes the loop in Ironlake interrupt handler.
It fixed irq lost issue on some Ironlake platforms.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zou Nan hai <Nanhai.zou@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Make sure hangcheck timer won't beat us unexpectedly on Ironlake.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch changes around our hotplug enable code a bit to only enable
it for ports we actually detect and initialize. This prevents problems
with stuck or spurious interrupts on outputs that aren't actually wired
up, and is generally more correct.
Fixes FDO bug #23183.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
A residual bare printk survived the merger of the hang detector, remove
this debugging left-over.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
This merges the upstream Intel tree and fixes up numerous conflicts
due to patches merged into Linus tree later in -rc cycle.
Conflicts:
drivers/char/agp/intel-agp.c
drivers/gpu/drm/drm_dp_i2c_helper.c
drivers/gpu/drm/i915/i915_irq.c
drivers/gpu/drm/i915/i915_suspend.c
IGD* isn't a useful name. Replace with the codenames, as sourced from
pci.ids.
Signed-off-by: Adam Jackson <ajax@redhat.com>
[anholt: Fixed up for merge with pineview/ironlake changes]
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Jakob Bornecrantz <jakob@vmware.com>
Acked-by: Thomas Hellström <thomas@shipmail.org>
Review-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse "Orange Smoothie" Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
HW guys have an evaluation about the impact about EOS, and say the impact
is quite small, so they have removed EOS detection support. This patch
removes EOS feature.
revert commit 0430296558
directly reverting it gives a hunk error, so please use this one.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
[anholt: fixed up commit message for update that the feature's really gone]
The master irq control in DE must be disabled before irq handling,
and enable after the process. This fixes the irq stall issue on
Ironlake.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zou, Nanhai <nanhai.zou@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add the support of ACPI opregion on Ironlake so that the backlight
brightness can be adjusted by using ACPI interface
>/sys/class/backlight/acpi_video0/brightness
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Zhao Yakui <yakui.zhao@intel.com>
[zhenyuw: cleanups, fix typo for checking GSE irq and convert to
current irq handling logic.]
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Replace the DRM_DEBUG with DRM_DEBUG_DRIVER in generic i915 driver.
Then the debug info can be obtained by adding the boot option of
"drm.debug=0x02".
At the same time the debug info in increase/decrease clock is also
printed by using DRM_DEBUG_DRIVER instead of DRM_DEBUG_KMS.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
If we trigger a tracepoint for batch buffer submission, it is a reasonable
assumption that we wish to also trace the batch buffer completion. So in
order to capture the completion events, we need to enable irqs... However,
we cannot rely on the completion event to disable the irq later, so we
defer the irq disable to the retire request.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
By adding tracepoint equivalents for WATCH_BUF/EXEC we are able to monitor
the lifetimes of objects, requests and significant events. These events can
then be probed using the tracing frameworks, such as systemtap and, in
particular, perf.
For example to record the stack trace for every GPU stall during a run, use
$ perf record -e i915:i915_gem_request_wait_begin -c 1 -g
And
$ perf report
to view the results.
[Updated to fix compilation issues caused.]
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Ben Gamari <bgamari@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
There is a very real possibility that multiple CPUs will notice that the
GPU is wedged. This introduces all sorts of potential race conditions.
Make the wedged flag atomic to mitigate this risk.
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch uses the previously introduced chip reset logic to reset the
chip when an error event is detected.
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch puts in place the machinery to attempt to reset the GPU. This
will be used when attempting to recover from a GPU hang.
Signed-off-by: Owain G. Ainsworth <oga@openbsd.org>
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We set a periodic timer to check on the GPU, resetting it every time a
batch is completed. If the timer elapses, we check acthd. If acthd
hasn't changed in two timer periods, we assume the chip is wedged.
This is implemented in such a way that it leaves the option open to
employ adaptive timer intervals in the future. One could wait until
several timer periods have elapsed before declaring the chip dead. If
the chip comes back after several periods but before the "dead"
threshold, the timer interval or dead threshold could be raised.
It is important to note that while checking for active requests, we need
to account for the fact that requests are removed from the list (i.e.
retired) in a deferred work queue handler. This means that merely
checking for an empty request_list is insufficient; the list could be
non-empty yet the GPU still idle, causing the hangcheck timer to
incorrectly mark the GPU as wedged (it took me a while to figure that
out---sigh...)
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In the event that any one of the DAC analog outputs (R,G,B) were driven
at full-scale (white video) or some analog level close to full-scale
voltage, and if the video cable were then disconnected, the analog video
voltage level would exceed the maximum electrical overstress limit of the
native (thin-oxide) transistors thus causing a long-term reliability concern.
The electrical overstress condition occurs in this particular case.
This patch address the IGD EOS (electrical overstress condition) issue.
When the EOS interrupt occurs, OS should disable DAC and then disable EOS,
then the normal hotplug operation follows.
TODO: it appears the normal unplug interrupt is missed as reported by Li Peng,
need more checks here.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch refactors the existing error detection and collection code,
placing most of it in i915_handle_error(). Additionally, we introduce a
work queue for scheduling post-crash tasks such as generating a uevent.
Using the uevent facility, userspace should be able to capture a
post-mortem dump for diagnostics.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch from jbarnes and myself adds FIFO watermark control to the
driver. This is needed for both power saving features on new platforms
with the so-called "big FIFO" and for controlling FIFO allocation
between pipes in multi-head configurations.
It's also necessary infrastructure to support things like framebuffer
compression and configuration supportability checks (i.e. checking a
configuration against available bandwidth).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch enables error detection by enabling several types of error
interrupts. When an error interrupt is received, the interrupt
handler captures the error state; hopefully resulting in an accurate
set of error data (error type, active head pointer, etc.). The new
record is then available from sysfs. The current code will also dump
the error state to the system log.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Update interrupt handling methods for IGDNG with new registers
for display and graphics interrupt functions. As we won't use
irq-based vblank sync in dri2, so display interrupt on new chip
will be used for hotplug only in future.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
All G4x and newer chips use the new style frame count register, with a
full 32 bit frame count. Update the code to reflect this.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Disable OpRegion support for now until verified on new chipsets.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add VGA port hotplug detection to the i915 driver. When KMS is enabled,
plugging in or removing a VGA cable from the VGA connector will
generate a uevent, which indicates to userspace that it should re-probe
outputs on this device (to determine modes, etc.).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: dropped extra PORT_HOTPLUG_STAT clear with ack from jbarnes]
Signed-off-by: Eric Anholt <eric@anholt.net>
This could be triggered by a client asking to emit an irq when the device
wasn't initialized.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
As discussed in the long thread about vblank related timeouts, it turns out
GM45 has different frame count registers than previous chips. This patch
adds support for them, which prevents us from waiting on really stale
sequence values in drm_wait_vblank (which rather than returning immediately
ends up timing out or getting interrupted).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
In some cases userland may be confused and try to wait on vblank events from
pipes that aren't actually enabled. We shouldn't allow this, so return
-EINVAL if the pipe isn't on.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This commit adds i915 driver support for the DRM mode setting APIs.
Currently, VGA, LVDS, SDVO DVI & VGA, TV and DVO LVDS outputs are
supported. HDMI, DisplayPort and additional SDVO output support will
follow.
Support for the mode setting code is controlled by the new 'modeset'
module option. A new config option, CONFIG_DRM_I915_KMS controls the
default behavior, and whether a PCI ID list is built into the module for
use by user level module utilities.
Note that if mode setting is enabled, user level drivers that access
display registers directly or that don't use the kernel graphics memory
manager will likely corrupt kernel graphics memory, disrupt output
configuration (possibly leading to hangs and/or blank displays), and
prevent panic/oops messages from appearing. So use caution when
enabling this code; be sure your user level code supports the new
interfaces.
A new SysRq key, 'g', provides emergency support for switching back to
the kernel's framebuffer console; which is useful for testing.
Co-authors: Dave Airlie <airlied@linux.ie>, Hong Liu <hong.liu@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is step one towards having multiple masters sharing a drm
device in order to get fast-user-switching to work.
It splits out the information associated with the drm master
into a separate kref counted structure, and allocates this when
a master opens the device node. It also allows the current master
to abdicate (say while VT switched), and a new master to take over
the hardware.
It moves the Intel and radeon drivers to using the sarea from
within the new master structures.
Signed-off-by: Dave Airlie <airlied@redhat.com>
drivers/gpu/drm/i915/i915_irq.c: In function 'i915_disable_pipestat':
drivers/gpu/drm/i915/i915_irq.c:101: warning: control may reach end of non-void function 'i915_pipestat' being inlined
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drm vblank initialization keeps track of the changes in driver-supplied
frame counts across vt switch and mode setting, but only if you let it by
not tearing down the drm vblank structure.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Because we write pipestat before iir, it's possible that a pipestat
interrupt will occur between the pipestat write and the iir write. This
leaves pipestat with an interrupt status not visible in iir. This may cause
an interrupt flood as we never clear the pipestat event.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The IMR masking was a technique recommended for avoiding getting stuck with
no interrupts generated again in MSI mode. It kept new IIR bits from getting
set between the IIR read and the IIR write, which would have otherwise
prevented an MSI from ever getting generated again. However, this caused a
problem for vblank as the IMR mask would keep the pipe event interrupt from
getting reflected in IIR, even after the IMR mask was brought back down.
Instead, just check the state of IIR after we ack the interrupts we're going
to handle, and restart if we didn't get IIR all the way to zero.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The pipestat fields affect reporting of all vblank-related interrupts, so we
have to reset them during the irq_handler, and while enabling vblank
interrupts. Otherwise, if a pipe status field had been set to non-zero
before enabling reporting, we would never see an interrupt again.
This patch adds i915_enable_pipestat and i915_disable_pipestat to abstract
out the steps needed to change the reported interrupts.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Addresses in the hardware status page below index 0x20 are reserved for use
by the hardware. The legacy breadcrumb was sitting at index 5. Move it to
index 0x21, and make sure everyone uses the defined value instead of
hard-coded constants.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
When userland detected that this ioctl was supported (by version number check),
it used it in a racy way -- dispatch delayed swap, wait for vblank, continue
rendering. As there was no mechanism for it to wait for the swap to finish,
sometimes it would render before the swap and garbage would be displayed on
the screen.
By removing the ioctl and returning -EINVAL, userland returns to its previous,
correct rendering path of waiting for a vblank then dispatching a swap. The
only path that could have used this ioctl correctly was page flipping, which
relied on only one client running and emitting wait-for-vblank-before-rendering
in the command stream. That path also falls back correctly, at the performance
cost of not being able to queue up rendering before the flip occurs.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
vblank in the kernel is far simpler if it deals with pipes instead of
planes, so we're changing both user and kernel side.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
To synchronize clip lists with the X server, the DRM lock must be held while
looking at drawable clip lists. To synchronize with other ring access, the
ring mutex must be held while inserting commands into the ring. Failure to
do the first resulted in easy visual corruption when moving windows, and the
second could have corrupted the ring with DRI2.
Grabbing the DRM lock involves using the DRM tasklet mechanism, grabbing the
ring mutex means potentially sleeping. Deal with both of these by always
running the tasklet from a work handler.
Also, protect from clip list changes since the vblank request was queued by
making sure the window has at least one rectangle while looking inside,
preventing oopses .
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Otherwise, if we lost the race, the pipestat bit would be set without being
reflected in IIR, and we would never clear the pipestat bit so the pipe
event would never be generated again, and all vblank waits would time out.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If the failing paths were hit, the vblank IRQ would never get turned off
again.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This uses the same spinlock as the user_irq code as it shares the same
register, ensuring that interrupt registers are updated atomically.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We fail ioctls that depend on the sarea_priv with EINVAL.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In the conversion for GEM, we had stopped using the hardware lock to protect
ring usage, since it was all internal to the DRM now. However, some paths
weren't converted to using struct_mutex to prevent multiple threads from
concurrently working on the ring, in particular between the vblank swap handler
and ioctls.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
GEM allows the creation of persistent buffer objects accessible by the
graphics device through new ioctls for managing execution of commands on the
device. The userland API is almost entirely driver-specific to ensure that
any driver building on this model can easily map the interface to individual
driver requirements.
GEM is used by the 2d driver for managing its internal state allocations and
will be used for pixmap storage to reduce memory consumption and enable
zero-copy GLX_EXT_texture_from_pixmap, and in the 3d driver is used to enable
GL_EXT_framebuffer_object and GL_ARB_pixel_buffer_object.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Previously, drivers supporting vblank interrupt waits would run the interrupt
all the time, or all the time that any 3d client was running, preventing the
CPU from sleeping for long when the system was otherwise idle. Now, interrupts
are disabled any time that no client is waiting on a vblank event. The new
method uses vblank counters on the chipsets when the interrupts are turned
off, rather than counting interrupts, so that we can continue to present
accurate vblank numbers.
Co-author: Michel Dänzer <michel@tungstengraphics.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds the support necessary for allowing ACPI backlight control to
work on some newer Intel-based graphics systems. Tested on Thinkpad T61
and HP 2510p hardware.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Previous attempts at interrupt mitigation had been foiled by i915_wait_irq's
failure to update the sarea seqno value when the status page indicated that
the seqno had already been passed. MSI support has been seen to cut CPU
costs by up to 40% in some workloads by avoiding other expensive interrupt
handlers for frequent graphics interrupts.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With the coming of kernel based modesetting and the memory manager stuff,
the everything in one directory approach was getting very ugly and
starting to be unmanageable.
This restructures the drm along the lines of other kernel components.
It creates a drivers/gpu/drm directory and moves the hw drivers into
subdirectores. It moves the includes into an include/drm, and
sets up the unifdef for the userspace headers we should be exporting.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Chris Wilson