Driver does only clock request + enable for DDR clocks. DDR clocks are
enabled by bootloader and need to stay that way in Linux. To avoid having
these clocks disabled by clock subsystem in case there are no Linux
consumers for them the clocks were marked as critical in clock drivers
(in commit 68b3b6f177 ("clk: at91: mark ddr clocks as critical")).
With this, there is no need to have a separate driver that only does
clock request + enable.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20230516072405.2696225-1-claudiu.beznea@microchip.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Add support for configuring the Self Refresh Power Down (SRPD)
inactivity timeout on Broadcom STB chips. This is used to conserve power
when the DRAM activity is reduced.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220812222533.2428033-4-f.fainelli@gmail.com
The Texas Instruments OMAP General Purpose Memory Controller (GPMC) is
only present on TI OMAP2/3/4/5, Keystone, AM33xx, AM43x, DRA7xx, TI81xx,
and K3 SoCs. Hence add a dependency on ARCH_OMAP2PLUS || ARCH_KEYSTONE
|| ARCH_K3, to prevent asking the user about this driver when
configuring a kernel without OMAP2+, Keystone, or K3 SoC family support.
Fixes: be34f45f0d ("memory: omap-gpmc: Make OMAP_GPMC config visible and selectable")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/f6780f572f882ed6ab5934321942cf2b412bf8d1.1652174849.git.geert+renesas@glider.be
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Allow OMAP_GPMC to be built as a module.
When building this driver as a module, the symbol
'of_default_bus_match_table' will not be found as it is not being
exported.
The of_match_node() call is redundant anyways as
of_platform_default_populate() already takes care of matching with
'of_default_bus_match_table'. So get rid of that call. This will also
resolve the module build failure.
Move compatible match table to the end where it is usually expected.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20220426082611.24427-3-rogerq@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
So far for armv7 TI platforms, GPMC was being selected by
arch/arm/mach-* architecture Kconfig files.
For K3 platforms, GPMC is no longer required for basic boot and cannot
be always enabled by default by mach- Kconfig.
We need a way for user (or board defconfig) to enable it if required so
make OMAP_GPMC Kconfig option always visible.
Drop COMPILE_TEST as build fails if IRQ_DOMAIN is not enabled.
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20220426082611.24427-2-rogerq@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
The Renesas RPC-IF driver calls devm_reset_control_get_exclusive(),
which returns -ENOTSUPP if CONFIG_RESET_CONTROLLER is not enabled.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/e443aa66d146da5646b7ebece8876545b8621063.1633447756.git.geert+renesas@glider.be
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Allow building the Broadcom STB DPFE driver as a module, it is already a
platform driver proper with all of the resource releasing device
managed.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Markus Mayer <mmayer@broadcom.com>
Link: https://lore.kernel.org/r/20210924031459.8911-1-f.fainelli@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Here is the large set of char/misc/whatever driver subsystem updates for
5.12-rc1. Over time it seems like this tree is collecting more and more
tiny driver subsystems in one place, making it easier for those
maintainers, which is why this is getting larger.
Included in here are:
- coresight driver updates
- habannalabs driver updates
- virtual acrn driver addition (proper acks from the x86
maintainers)
- broadcom misc driver addition
- speakup driver updates
- soundwire driver updates
- fpga driver updates
- amba driver updates
- mei driver updates
- vfio driver updates
- greybus driver updates
- nvmeem driver updates
- phy driver updates
- mhi driver updates
- interconnect driver udpates
- fsl-mc bus driver updates
- random driver fix
- some small misc driver updates (rtsx, pvpanic, etc.)
All of these have been in linux-next for a while, with the only reported
issue being a merge conflict in include/linux/mod_devicetable.h that you
will hit in your tree due to the dfl_device_id addition from the fpga
subsystem in here. The resolution should be simple.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYDZf9w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk3xgCcCEN+pCJTum+uAzSNH3YKs/onaDgAnRSVwOUw
tNW6n1JhXLYl9f5JdhvS
=MOHs
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the large set of char/misc/whatever driver subsystem updates
for 5.12-rc1. Over time it seems like this tree is collecting more and
more tiny driver subsystems in one place, making it easier for those
maintainers, which is why this is getting larger.
Included in here are:
- coresight driver updates
- habannalabs driver updates
- virtual acrn driver addition (proper acks from the x86 maintainers)
- broadcom misc driver addition
- speakup driver updates
- soundwire driver updates
- fpga driver updates
- amba driver updates
- mei driver updates
- vfio driver updates
- greybus driver updates
- nvmeem driver updates
- phy driver updates
- mhi driver updates
- interconnect driver udpates
- fsl-mc bus driver updates
- random driver fix
- some small misc driver updates (rtsx, pvpanic, etc.)
All of these have been in linux-next for a while, with the only
reported issue being a merge conflict due to the dfl_device_id
addition from the fpga subsystem in here"
* tag 'char-misc-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (311 commits)
spmi: spmi-pmic-arb: Fix hw_irq overflow
Documentation: coresight: Add PID tracing description
coresight: etm-perf: Support PID tracing for kernel at EL2
coresight: etm-perf: Clarify comment on perf options
ACRN: update MAINTAINERS: mailing list is subscribers-only
regmap: sdw-mbq: use MODULE_LICENSE("GPL")
regmap: sdw: use no_pm routines for SoundWire 1.2 MBQ
regmap: sdw: use _no_pm functions in regmap_read/write
soundwire: intel: fix possible crash when no device is detected
MAINTAINERS: replace my with email with replacements
mhi: Fix double dma free
uapi: map_to_7segment: Update example in documentation
uio: uio_pci_generic: don't fail probe if pdev->irq equals to IRQ_NOTCONNECTED
drivers/misc/vmw_vmci: restrict too big queue size in qp_host_alloc_queue
firewire: replace tricky statement by two simple ones
vme: make remove callback return void
firmware: google: make coreboot driver's remove callback return void
firmware: xilinx: Use explicit values for all enum values
sample/acrn: Introduce a sample of HSM ioctl interface usage
virt: acrn: Introduce an interface for Service VM to control vCPU
...
Add support for building the SMI driver as module. Switch MTK_SMI to
tristate, and add module_exit/module_license.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Link: https://lore.kernel.org/r/20210126060055.11050-1-yong.wu@mediatek.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This driver is for the EMIF private feature implemented under FPGA
Device Feature List (DFL) framework. It is used to expose memory
interface status information as well as memory clearing control.
The purpose of memory clearing block is to zero out all private memory
when FPGA is to be reprogrammed. This gives users a reliable method to
prevent potential data leakage.
[mdf@kernel.org: Fixed up ABI doc]
Reviewed-by: Tom Rix <trix@redhat.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Link: https://lore.kernel.org/r/20210107043714.991646-9-mdf@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Renesas RPC-IF is present on the RZ/G2 Series. Add that to
the description.
Suggested-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210102115412.3402059-2-aford173@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The driver can be compile-tested on all ARM machines, but
causes a failure when built for ARMv7-M:
arm-linux-gnueabi-ld: error: drivers/memory/ti-emif-sram-pm.o: conflicting architecture profiles A/M
Limit the target machines to configurations that have ARMv7 enabled.
Fixes: ea0c0ad6b6 ("memory: Enable compile testing for most of the drivers")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201203230832.1481767-1-arnd@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The pl353-smc driver uses module_amba_driver so it has a build
dependency on CONFIG_ARM_AMBA:
/usr/bin/arm-linux-gnueabi-ld: drivers/memory/pl353-smc.o: in function `pl353_smc_driver_init':
pl353-smc.c:(.init.text+0x10): undefined reference to `amba_driver_register'
However it still can be compile tested on platforms other than ARM,
which in practice is limited to those selecting ARM_AMBA (so only
ARM64).
Fixes: ea0c0ad6b6 ("memory: Enable compile testing for most of the drivers")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/20201029193357.389593-1-krzk@kernel.org
SPARC comes without CONFIG_OF_ADDRESS thus compile testing fails on
linking:
/usr/bin/sparc64-linux-gnu-ld: drivers/memory/omap-gpmc.o: in function `gpmc_probe_generic_child':
omap-gpmc.c:(.text.unlikely+0x14ec): undefined reference to `of_platform_device_create'
Fixes: ea0c0ad6b6 ("memory: Enable compile testing for most of the drivers")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20200911143251.399-1-krzk@kernel.org
Most of the memory controller drivers do not depend on architecture
specific code so can be compile tested to increase build coverage.
When compile tested, do not enable them by default.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200724074038.5597-7-krzk@kernel.org
Add separate entry for Broadcom STB DPFE driver, enabled by default on
ARCH_BRCMSTB. This allows compile testing.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
* Spelling
* http to https updates
NAND core changes:
* Drop useless 'depends on' in Kconfig
* Add an extra level in the Kconfig hierarchy
* Trivial spellings
* Dynamic allocation of the interface configurations
* Dropping the default ONFI timing mode
* Various cleanup (types, structures, naming, comments)
* Hide the chip->data_interface indirection
* Add the generic rb-gpios property
* Add the ->choose_interface_config() hook
* Introduce nand_choose_best_sdr_timings()
* Use default values for tPROG_max and tBERS_max
* Avoid redefining tR_max and tCCS_min
* Add a helper to find the closest ONFI mode
* bcm63xx MTD parsers: simplify CFE detection
Raw NAND controller drivers changes:
* fsl-upm: Deprecation of specific DT properties
* fsl_upm: Driver rework and cleanup in favor of ->exec_op()
* Ingenic: Cleanup ARRAY_SIZE() vs sizeof() use
* brcmnand: ECC error handling on EDU transfers
* brcmnand: Don't default to EDU transfers
* qcom: Set BAM mode only if not set already
* qcom: Avoid write to unavailable register
* gpio: Driver rework in favor of ->exec_op()
* tango: ->exec_op() conversion
* mtk: ->exec_op() conversion
Raw NAND chip drivers changes:
* toshiba: Implement ->choose_interface_config() for TH58NVG2S3HBAI4
* toshiba: Implement ->choose_interface_config() for TC58NVG0S3E
* toshiba: Implement ->choose_interface_config() for TC58TEG5DCLTA00
* hynix: Implement ->choose_interface_config() for H27UCG8T2ATR-BC
SPI NOR core changes:
* Disable Quad Mode in spi_nor_restore().
* Don't abort BFPT parsing when QER reserved value is used.
* Add support/update capabilities for few flashes.
* Drop s70fl01gs flash: it does not support RDSR(05h) which
is critical for erase/write.
* Merge the SPIMEM DTR bits in spi-nor/next to avoid conflicts
during the release cycle.
SPI NOR controller drivers changes:
* Move the cadence-quadspi driver to spi-mem. The series was
taken through the SPI tree. Merge it also in spi-nor/next
to avoid conflicts during the release cycle.
* intel-spi:
- Add new PCI IDs.
- Ignore the Write Disable command, the controller doesn't
support it.
- Fix performance regression.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl8vJtMACgkQJWrqGEe9
VoRdGAf/Y5m5BwmLilkEYpffyxi7dVR6XOKPLU5EJXkS3dPvH9398zchbHOdedCZ
OzJIfh6Iv+qbkgS2g0lAAT+SAfOfG9plubvSdkjrHXl4eZXRnR/49RF5LAEju7sz
Uw1HdRcawyEi5uI9yYS0tCeVMIUJq+5x7VibH+82yOIdSPc60c7FDc5ih/nVKj/a
Pn9LOzGzkdndcE1b3FcF2Uk/T1YOJx3Yt5ngALlPpJxaDZmQSHtYPuuz8DfUbamf
uj3CkpqYRyT18CzuFvtuba6LyF+donXNJgvl6ivW7dlRSPzSMnDQu7J5bpNhUfcd
p/ZdzX1Jxle4theDm0J9ALsSSM5g2w==
=RiY8
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"MTD core changes:
- Spelling
- http to https updates
NAND core changes:
- Drop useless 'depends on' in Kconfig
- Add an extra level in the Kconfig hierarchy
- Trivial spellings
- Dynamic allocation of the interface configurations
- Dropping the default ONFI timing mode
- Various cleanup (types, structures, naming, comments)
- Hide the chip->data_interface indirection
- Add the generic rb-gpios property
- Add the ->choose_interface_config() hook
- Introduce nand_choose_best_sdr_timings()
- Use default values for tPROG_max and tBERS_max
- Avoid redefining tR_max and tCCS_min
- Add a helper to find the closest ONFI mode
- bcm63xx MTD parsers: simplify CFE detection
Raw NAND controller drivers changes:
- fsl-upm: Deprecation of specific DT properties
- fsl_upm: Driver rework and cleanup in favor of ->exec_op()
- Ingenic: Cleanup ARRAY_SIZE() vs sizeof() use
- brcmnand: ECC error handling on EDU transfers
- brcmnand: Don't default to EDU transfers
- qcom: Set BAM mode only if not set already
- qcom: Avoid write to unavailable register
- gpio: Driver rework in favor of ->exec_op()
- tango: ->exec_op() conversion
- mtk: ->exec_op() conversion
Raw NAND chip drivers changes:
- toshiba: Implement ->choose_interface_config() for TH58NVG2S3HBAI4,
TC58NVG0S3E, and TC58TEG5DCLTA00
- hynix: Implement ->choose_interface_config() for H27UCG8T2ATR-BC
SPI NOR core changes:
- Disable Quad Mode in spi_nor_restore().
- Don't abort BFPT parsing when QER reserved value is used.
- Add support/update capabilities for few flashes.
- Drop s70fl01gs flash: it does not support RDSR(05h) which is
critical for erase/write.
- Merge the SPIMEM DTR bits in spi-nor/next to avoid conflicts during
the release cycle.
SPI NOR controller drivers changes:
- Move the cadence-quadspi driver to spi-mem. The series was taken
through the SPI tree. Merge it also in spi-nor/next to avoid
conflicts during the release cycle.
- intel-spi:
- Add new PCI IDs.
- Ignore the Write Disable command, the controller doesn't support
it.
- Fix performance regression"
* tag 'mtd/for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (79 commits)
MTD: pfow.h: drop a duplicated word
MTD: mtd-abi.h: drop a duplicated word
mtd: rawnand: omap_elm: Replace HTTP links with HTTPS ones
mtd: Replace HTTP links with HTTPS ones
mtd: hyperbus: Replace HTTP links with HTTPS ones
mtd: revert "spi-nor: intel: provide a range for poll_timout"
mtd: spi-nor: update read capabilities for w25q64 and s25fl064k
mtd: spi-nor: micron: Add SPI_NOR_DUAL_READ flag on mt25qu02g
mtd: spi-nor: macronix: Add support for mx66u2g45g
mtd: spi-nor: intel-spi: Simulate WRDI command
mtd: spi-nor: Disable the flash quad mode in spi_nor_restore()
mtd: spi-nor: Add capability to disable flash quad mode
mtd: spi-nor: spansion: Remove s70fl01gs from flash_info
mtd: spi-nor: sfdp: do not make invalid quad enable fatal
dt-bindings: mtd: fsl-upm-nand: Deprecate chip-delay and fsl, upm-wait-flags
mtd: rawnand: stm32_fmc2: get resources from parent node
mtd: rawnand: stm32_fmc2: use regmap APIs
memory: stm32-fmc2-ebi: add STM32 FMC2 EBI controller driver
dt-bindings: memory-controller: add STM32 FMC2 EBI controller documentation
dt-bindings: mtd: update STM32 FMC2 NAND controller documentation
...
- improvements for Loongson64
- extended ingenic support
- removal of not maintained paravirt system type
- cleanups and fixes
-----BEGIN PGP SIGNATURE-----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=I/vU
-----END PGP SIGNATURE-----
Merge tag 'mips_5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS upates from Thomas Bogendoerfer:
- improvements for Loongson64
- extended ingenic support
- removal of not maintained paravirt system type
- cleanups and fixes
* tag 'mips_5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (81 commits)
MIPS: SGI-IP27: always enable NUMA in Kconfig
MAINTAINERS: Update KVM/MIPS maintainers
MIPS: Update default config file for Loongson-3
MIPS: KVM: Add kvm guest support for Loongson-3
dt-bindings: mips: Document Loongson kvm guest board
MIPS: handle Loongson-specific GSExc exception
MIPS: add definitions for Loongson-specific CP0.Diag1 register
MIPS: only register FTLBPar exception handler for supported models
MIPS: ingenic: Hardcode mem size for qi,lb60 board
MIPS: DTS: ingenic/qi,lb60: Add model and memory node
MIPS: ingenic: Use fw_passed_dtb even if CONFIG_BUILTIN_DTB
MIPS: head.S: Init fw_passed_dtb to builtin DTB
of: address: Fix parser address/size cells initialization
of_address: Guard of_bus_pci_get_flags with CONFIG_PCI
MIPS: DTS: Fix number of msi vectors for Loongson64G
MIPS: Loongson64: Add ISA node for LS7A PCH
MIPS: Loongson64: DTS: Fix ISA and PCI I/O ranges for RS780E PCH
MIPS: Loongson64: Enlarge IO_SPACE_LIMIT
MIPS: Loongson64: Process ISA Node in DeviceTree
of_address: Add bus type match for pci ranges parser
...
A fairly quiet release for SPI, nothing really going on in the core
although there's been quite a bit of driver related activity. This pull
request includes the addition of some shared code in drivers/memory for
the Renesas RPC-IF which is used by a newly added SPI driver, the memory
subsystem doesn't seem to have a fixed maintainer at the minute and this
seemed like the most sensible way to get that hardware supported.
- Quite a few cleanups and optimizations for the Altera, Qualcomm GENI,
sun6i and lantiq drivers.
- Several more GPIO descriptor conversions.
- Move the Cadence QuadSPI driver from drivers/mtd to drivers/spi.
- New support for Mediatek MT8192 and Renesas RPC-IF, R8A7742 and
R8A774e1.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl8oBFoTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0P2UB/47NlDsAadOiOB0ZzPKdn4Nr5BLvUza
TP63gAsxD4BErzgf/p/0D8qUTZPzmlfA833gj9hkIavJlTmv3fGrH0XeHg2OuCJb
yhyw9pE7MPpnARVOJHz1MZkAT/dY+sF3TaUXysmymlvs6CLqRnsLTOwK2f92SeGH
ygpC4J1tfD961xWmv2Zt8wNuQXtH+JePLXeZFSx2ZkpToFT56QO6kFpWjVfDquY4
/F8bc7qyXX6FcsBYAG6Ly35OSxbPazVLkTaDWQr5V4TAD0DXw0NOyvxg2OccqE31
y1jjx3hn98sN73m/VLzlEOer4w9313K5BOISaN0z7TQSQ55XRZKe4EQj
=K1PB
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A fairly quiet release for SPI, nothing really going on in the core
although there's been quite a bit of driver related activity.
This includes the addition of some shared code in drivers/memory for
the Renesas RPC-IF which is used by a newly added SPI driver, the
memory subsystem doesn't seem to have a fixed maintainer at the minute
and this seemed like the most sensible way to get that hardware
supported.
- Quite a few cleanups and optimizations for the Altera, Qualcomm
GENI, sun6i and lantiq drivers.
- Several more GPIO descriptor conversions.
- Move the Cadence QuadSPI driver from drivers/mtd to drivers/spi.
- New support for Mediatek MT8192 and Renesas RPC-IF, R8A7742 and
R8A774e1"
* tag 'spi-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (119 commits)
dt-bindings: lpspi: New property in document DT bindings for LPSPI
spi: lpspi: fix using CS discontinuously on i.MX8DXLEVK
spi: lpspi: remove unused fsl_lpspi->chipselect
spi: lpspi: Fix kernel warning dump when probe fail after calling spi_register
spi: rockchip: Fix error in SPI slave pio read
spi: rockchip: Support 64-location deep FIFOs
spi: rockchip: Config spi rx dma burst size depend on xfer length
spi: spi-topcliff-pch: drop call to wakeup-disable
spi: spidev: Align buffers for DMA
spi: correct kernel-doc inconsistency
spi: sun4i: update max transfer size reported
spi: imx: enable runtime pm support
spi: update bindings for MT8192 SoC
spi: mediatek: add spi support for mt8192 IC
spi: Add bindings for Lightning Mountain SoC
spi: lantiq: Add support to Lightning Mountain SoC
spi: lantiq: Move interrupt configuration to SoC specific data structure
spi: lantiq: Add fifo size bit mask in SoC specific data structure
spi: lantiq: Add support to acknowledge interrupt
spi: lantiq: Move interrupt control register offesets to SoC specific data structure
...
Enabling the JZ4780_NEMC driver makes sense only for specific hardware -
the Ingenic SoC architecture. It is not an essential driver for the SoC
support so do not enable it by default.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add the memory driver for Renesas RPC-IF which registers either SPI or
HyperFLash device depending on the contents of the device tree subnode.
It also provides the absract "back end" device APIs that can be used by
the "front end" SPI/MTD drivers to talk to the real hardware.
Based on the original patch by Mason Yang <masonccyang@mxic.com.tw>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Link: https://lore.kernel.org/r/9a3606ec-d4d0-c63a-4fb6-631ab38e621c@cogentembedded.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Baikal-T1 SoC provides a way to tune the MIPS P5600 CM2 L2-cache
performance up. It can be done by changing the L2-RAM Data/Tag/WS
latencies in a dedicated register exposed by the system controller.
The driver added by this commit provides a dts properties-based and
sysfs-based interface for it. The device DT node is supposed to be a
child of Baikal-T1 System Controller node.
Link: https://lore.kernel.org/r/20200526125928.17096-7-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: soc@kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
- A driver for SCU (system control) on NXP i.MX8QXP
- Qualcomm Always-on Subsystem messaging driver (AOSS QMP)
- Qualcomm PM support for MSM8998
- Support for a newer version of DRAM PHY driver for Broadcom (DPFE)
- Reset controller support for Bitmain BM1880
- TI SCI (System Control Interface) support for CPU control on AM654
processors
- More TI sysc refactoring and rework
-----BEGIN PGP SIGNATURE-----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=ek+j
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms and a couple of the small driver
subsystems we merge through our tree:
- A driver for SCU (system control) on NXP i.MX8QXP
- Qualcomm Always-on Subsystem messaging driver (AOSS QMP)
- Qualcomm PM support for MSM8998
- Support for a newer version of DRAM PHY driver for Broadcom (DPFE)
- Reset controller support for Bitmain BM1880
- TI SCI (System Control Interface) support for CPU control on AM654
processors
- More TI sysc refactoring and rework"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (84 commits)
reset: remove redundant null check on pointer dev
soc: rockchip: work around clang warning
dt-bindings: reset: imx7: Fix the spelling of 'indices'
soc: imx: Add i.MX8MN SoC driver support
soc: aspeed: lpc-ctrl: Fix probe error handling
soc: qcom: geni: Add support for ACPI
firmware: ti_sci: Fix gcc unused-but-set-variable warning
firmware: ti_sci: Use the correct style for SPDX License Identifier
soc: imx8: Use existing of_root directly
soc: imx8: Fix potential kernel dump in error path
firmware/psci: psci_checker: Park kthreads before stopping them
memory: move jedec_ddr.h from include/memory to drivers/memory/
memory: move jedec_ddr_data.c from lib/ to drivers/memory/
MAINTAINERS: Remove myself as qcom maintainer
soc: aspeed: lpc-ctrl: make parameter optional
soc: qcom: apr: Don't use reg for domain id
soc: qcom: fix QCOM_AOSS_QMP dependency and build errors
memory: tegra: Fix -Wunused-const-variable
firmware: tegra: Early resume BPMP
soc/tegra: Select pinctrl for Tegra194
...
Depending on MACH_JZ4780 prevent us from creating a generic kernel that
works on more than one MIPS board. Instead, we just depend on MIPS being
set.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
jedec_ddr_data.c exports 3 symbols, and all of them are only
referenced from drivers/memory/{emif.c,of_memory.c}
drivers/memory/ is a better location than lib/.
I removed the Kconfig prompt "JEDEC DDR data" because it is only
select'ed by TI_EMIF, and there is no other user. There is no good
reason in making it a user-configurable CONFIG option.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add driver for arm pl353 static memory controller. This controller is used in
Xilinx Zynq SoC for interfacing the NAND and NOR/SRAM memory devices.
Signed-off-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
JZ4780_NEMC doesn't depend on OF, and if OF isn't enabled we get this
error:
drivers/memory/jz4780-nemc.c: In function ‘jz4780_nemc_num_banks’:
drivers/memory/jz4780-nemc.c:72:10: error: implicit declaration of
function ‘of_read_number’; did you mean ‘down_read_nested’?
[-Werror=implicit-function-declaration]
bank = of_read_number(prop, 1);
^~~~~~~~~~~~~~
down_read_nested
Make JZ4780_NEMC depend on OF.
Fixes: ab99e11062 ("memory: jz4780-nemc: Allow selection of this driver when COMPILE_TEST=y")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes maintainers' life easier by allowing them to compile-test
this driver without having MACH_JZ4780 enabled.
We also need to add a dependency on HAS_IOMEM to make sure the
driver compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes maintainers' life easier by allowing them to compile-test
this driver without having FSL_SOC, ARCH_LAYERSCAPE or SOC_LS1021A
enabled.
We also need to add a dependency on HAS_IOMEM to make sure the
driver compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tegra30+ has some minor differences in registers / bits layout compared
to Tegra20. Let's squash Tegra20 driver into the common tegra-mc driver
in a preparation for the upcoming MC hot reset controls implementation,
avoiding code duplication.
Note that this currently doesn't report the value of MC_GART_ERROR_REQ
because it is located within the GART register area and cannot be safely
accessed from the MC driver (this happens to work only by accident). The
proper solution is to integrate the GART driver with the MC driver, much
like is done for the Tegra SMMU, but that is an invasive change and will
be part of a separate patch series.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Certain SoCs like Texas Instruments AM335x and AM437x require parts
of the EMIF PM code to run late in the suspend sequence from SRAM,
such as saving and restoring the EMIF context and placing the memory
into self-refresh.
One requirement for these SoCs to suspend and enter its lowest power
mode, called DeepSleep0, is that the PER power domain must be shut off.
Because the EMIF (DDR Controller) resides within this power domain, it
will lose context during a suspend operation, so we must save it so we
can restore once we resume. However, we cannot execute this code from
external memory, as it is not available at this point, so the code must
be executed late in the suspend path from SRAM.
This patch introduces a ti-emif-sram driver that includes several
functions written in ARM ASM that are relocatable so the PM SRAM
code can use them. It also allocates a region of writable SRAM to
be used by the code running in the executable region of SRAM to save
and restore the EMIF context. It can export a table containing the
absolute addresses of the available PM functions so that other SRAM
code can branch to them. This code is required for suspend/resume on
AM335x and AM437x to work.
In addition to this, to be able to share data structures between C and
the ti-emif-sram-pm assembly code, we can automatically generate all of
the C struct member offsets and sizes as macros by processing
emif-asm-offsets.c into assembly code and then extracting the relevant
data as is done for the generated platform asm-offsets.h files.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
NAND, from Boris:
"""
- some minor fixes/improvements on existing drivers (fsmc, gpio, ifc,
davinci, brcmnand, omap)
- a huge cleanup/rework of the denali driver accompanied with core
fixes/improvements to simplify the driver code
- a complete rewrite of the atmel driver to support new DT bindings
make future evolution easier
- the addition of per-vendor detection/initialization steps to avoid
extending the nand_ids table with more extended-id entries
"""
SPI NOR, from Cyrille:
"""
- fixes in the hisi SPI controller driver.
- fixes in the intel SPI controller driver.
- fixes in the Mediatek SPI controller driver.
- fixes to some SPI flash memories not supported the Chip Erase command.
- add support to some new memory parts (Winbond, Macronix, Micron, ESMT).
- add new driver for the STM32 QSPI controller.
"""
And a few fixes for Gemini and Versatile platforms on physmap-of
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dxj5
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20170510' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"NAND, from Boris:
- some minor fixes/improvements on existing drivers (fsmc, gpio, ifc,
davinci, brcmnand, omap)
- a huge cleanup/rework of the denali driver accompanied with core
fixes/improvements to simplify the driver code
- a complete rewrite of the atmel driver to support new DT bindings
make future evolution easier
- the addition of per-vendor detection/initialization steps to avoid
extending the nand_ids table with more extended-id entries
SPI NOR, from Cyrille:
- fixes in the hisi, intel and Mediatek SPI controller drivers
- fixes to some SPI flash memories not supporting the Chip Erase
command.
- add support to some new memory parts (Winbond, Macronix, Micron,
ESMT).
- add new driver for the STM32 QSPI controller
And a few fixes for Gemini and Versatile platforms on physmap-of"
* tag 'for-linus-20170510' of git://git.infradead.org/linux-mtd: (100 commits)
MAINTAINERS: Update NAND subsystem git repositories
mtd: nand: gpio: update binding
mtd: nand: add ooblayout for old hamming layout
mtd: oxnas_nand: Allocating more than necessary in probe()
dt-bindings: mtd: Document the STM32 QSPI bindings
mtd: mtk-nor: set controller's address width according to nor flash
mtd: spi-nor: add driver for STM32 quad spi flash controller
mtd: nand: brcmnand: Check flash #WP pin status before nand erase/program
mtd: nand: davinci: add comment on NAND subpage write status on keystone
mtd: nand: omap2: Fix partition creation via cmdline mtdparts
mtd: nand: NULL terminate a of_device_id table
mtd: nand: Fix a couple error codes
mtd: nand: allow drivers to request minimum alignment for passed buffer
mtd: nand: allocate aligned buffers if NAND_OWN_BUFFERS is unset
mtd: nand: denali: allow to override revision number
mtd: nand: denali_dt: use pdev instead of ofdev for platform_device
mtd: nand: denali_dt: remove dma-mask DT property
mtd: nand: denali: support 64bit capable DMA engine
mtd: nand: denali_dt: enable HW_ECC_FIXUP for Altera SOCFPGA variant
mtd: nand: denali: support HW_ECC_FIXUP capability
...
New helpers/macros have been to atmel-smc.h introduced to simplify SMC
regs manipulation. Rework the code to use those helpers, and simplify
the ->xlate_config(), ->get_config() and ->apply_config() implementations.
SMC configs are now stored in a struct atmel_smc_cs_conf object that
directly contains registers values, which should help implementing
->suspend()/->resume() hooks.
We can also get rid of those regmap fields (and the associated ->init()
hook) which are not longer needed thanks to the
atmel_[h]smc_cs_conf_{apply,get}() helpers.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
As Freescale/NXP IFC controller is available on LS1021A, the dependency
for LS1021A is added.
LS1021A is an earlier product and is not compatible with later
LayerScape architecture. So ARCH_LAYERSCAPE can't cover LS1021A.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Create a new driver for the da8xx DDR2/mDDR controller and implement
support for writing to the Peripheral Bus Burst Priority Register.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
[nsekhar@ti.com: subject line adjustment]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
NAND:
Updates from Boris:
"""
This pull request contains only one notable change:
* Addition of the MTK NAND controller driver
And a bunch of specific NAND driver improvements/fixes. Here are the
changes that are worth mentioning:
* A few fixes/improvements for the xway NAND controller driver
* A few fixes for the sunxi NAND controller driver
* Support for DMA in the sunxi NAND driver
* Support for the sunxi NAND controller IP embedded in A23/A33 SoCs
* Addition for bitflips detection in erased pages to the brcmnand driver
* Support for new brcmnand IPs
* Update of the OMAP-GPMC binding to support DMA channel description
"""
In addition, some small fixes around error handling, etc., as well as one
long-standing corner case issue (2.6.20, I think?) with writing 1 byte less
than a page.
NOR:
* Rework some error handling on reads and writes, so we can better handle (for
instance) SPI controllers which have limitations on their maximum transfer size
* Add new Cadence Quad SPI flash controller driver
* Add new Atmel QSPI flash controller driver
* Add new Hisilicon SPI flash controller driver
* Support a few new flash, and update supported features on others
* Fix the logic used for detecting a fully-unlocked flash
And other miscellaneous small fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HQr0
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20160801' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"NAND:
Quoting Boris:
'This pull request contains only one notable change:
- Addition of the MTK NAND controller driver
And a bunch of specific NAND driver improvements/fixes. Here are the
changes that are worth mentioning:
- A few fixes/improvements for the xway NAND controller driver
- A few fixes for the sunxi NAND controller driver
- Support for DMA in the sunxi NAND driver
- Support for the sunxi NAND controller IP embedded in A23/A33 SoCs
- Addition for bitflips detection in erased pages to the brcmnand driver
- Support for new brcmnand IPs
- Update of the OMAP-GPMC binding to support DMA channel description'
In addition, some small fixes around error handling, etc., as well
as one long-standing corner case issue (2.6.20, I think?) with
writing 1 byte less than a page.
NOR:
- rework some error handling on reads and writes, so we can better
handle (for instance) SPI controllers which have limitations on
their maximum transfer size
- add new Cadence Quad SPI flash controller driver
- add new Atmel QSPI flash controller driver
- add new Hisilicon SPI flash controller driver
- support a few new flash, and update supported features on others
- fix the logic used for detecting a fully-unlocked flash
And other miscellaneous small fixes"
* tag 'for-linus-20160801' of git://git.infradead.org/linux-mtd: (60 commits)
mtd: spi-nor: don't build Cadence QuadSPI on non-ARM
mtd: mtk-nor: remove duplicated include from mtk-quadspi.c
mtd: nand: fix bug writing 1 byte less than page size
mtd: update description of MTD_BCM47XXSFLASH symbol
mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller
mtd: spi-nor: Bindings for Cadence Quad SPI Flash Controller driver
mtd: nand: brcmnand: Change BUG_ON in brcmnand_send_cmd
mtd: pmcmsp-flash: Allocating too much in init_msp_flash()
mtd: maps: sa1100-flash: potential NULL dereference
mtd: atmel-quadspi: add driver for Atmel QSPI controller
mtd: nand: omap2: fix return value check in omap_nand_probe()
Documentation: atmel-quadspi: add binding file for Atmel QSPI driver
mtd: spi-nor: add hisilicon spi-nor flash controller driver
mtd: spi-nor: support dual, quad, and WP for Gigadevice
mtd: spi-nor: Added support for n25q00a.
memory: Update dependency of IFC for Layerscape
mtd: nand: jz4780: Update MODULE_AUTHOR email address
mtd: nand: sunxi: prevent a small memory leak
mtd: nand: sunxi: add reset line support
mtd: nand: sunxi: update DT bindings
...
This patch enables IFC NAND support on ARM layerscape platform.
It fixes the dependency to enable NAND. The include files are being modified
to ensure complilation for both PowerPC and ARM architectures.
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The EBI (External Bus Interface) is used to access external peripherals
(NOR, SRAM, NAND, and other specific devices like ethernet controllers).
Each device is assigned a CS line and an address range and can have its
own configuration (timings, access mode, bus width, ...).
This driver provides a generic DT binding to configure a device according
to its requirements.
For specific device controllers (like the NAND one) the SMC timings
should be configured by the controller driver through the matrix and
smc syscon regmaps.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
First cycle with Boris as NAND maintainer! Many (most) bullets stolen from him.
Generic:
* Migrated NAND LED trigger to be a generic MTD trigger
NAND:
* Introduction of the "ECC algorithm" concept, to avoid overloading the ECC
mode field too much more
* Replaced the nand_ecclayout infrastructure with something a little more
flexible (finally!) and future proof
* Rework of the OMAP GPMC and NAND drivers; the TI folks pulled some of
this into their own tree as well
* Prepare the sunxi NAND driver to receive DMA support
* Handle bitflips in erased pages on GPMI revisions that do not support
this in hardware.
SPI NOR:
* Start using the spi_flash_read() API for SPI drivers that support it (i.e.,
SPI drivers with special memory-mapped flash modes)
And other small scattered improvments.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=J6KN
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20160523' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"First cycle with Boris as NAND maintainer! Many (most) bullets stolen
from him.
Generic:
- Migrated NAND LED trigger to be a generic MTD trigger
NAND:
- Introduction of the "ECC algorithm" concept, to avoid overloading
the ECC mode field too much more
- Replaced the nand_ecclayout infrastructure with something a little
more flexible (finally!) and future proof
- Rework of the OMAP GPMC and NAND drivers; the TI folks pulled some
of this into their own tree as well
- Prepare the sunxi NAND driver to receive DMA support
- Handle bitflips in erased pages on GPMI revisions that do not
support this in hardware.
SPI NOR:
- Start using the spi_flash_read() API for SPI drivers that support
it (i.e., SPI drivers with special memory-mapped flash modes)
And other small scattered improvments"
* tag 'for-linus-20160523' of git://git.infradead.org/linux-mtd: (155 commits)
mtd: spi-nor: support GigaDevice gd25lq64c
mtd: nand_bch: fix spelling of "probably"
mtd: brcmnand: respect ECC algorithm set by NAND subsystem
gpmi-nand: Handle ECC Errors in erased pages
Documentation: devicetree: deprecate "soft_bch" nand-ecc-mode value
mtd: nand: add support for "nand-ecc-algo" DT property
mtd: mtd: drop NAND_ECC_SOFT_BCH enum value
mtd: drop support for NAND_ECC_SOFT_BCH as "soft_bch" mapping
mtd: nand: read ECC algorithm from the new field
mtd: nand: fsmc: validate ECC setup by checking algorithm directly
mtd: nand: set ECC algorithm to Hamming on fallback
staging: mt29f_spinand: set ECC algorithm explicitly
CRIS v32: nand: set ECC algorithm explicitly
mtd: nand: atmel: set ECC algorithm explicitly
mtd: nand: davinci: set ECC algorithm explicitly
mtd: nand: bf5xx: set ECC algorithm explicitly
mtd: nand: omap2: Fix high memory dma prefetch transfer
mtd: nand: omap2: Start dma request before enabling prefetch
mtd: nandsim: add __init attribute
mtd: nand: move of_get_nand_xxx() helpers into nand_base.c
...
This patch adds Exynos SROM controller driver which will handle
save restore of SROM registers during S2R.
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[p.fedin@samsung.com: tested on SMDK5410]
Tested-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
[k.kozlowski: Minor COMPILE_TEST adjustments in Kconfig entries]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
OMAPs can have 2 to 4 WAITPINs that can be used as general purpose
input if not used for memory wait state insertion.
The first user will be the OMAP NAND chip to get the NAND
read/busy status using gpiolib.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
This patch add SMI(Smart Multimedia Interface) driver. This driver
is responsible to enable/disable iommu and control the power domain
and clocks of each local arbiter.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Tested-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Commit 63aa945b10 ("memory: omap-gpmc: Add Kconfig option for debug")
added a debug option for GPMC, but somehow managed to keep it unselectable.
This probably happened because I had some uncommitted changes and the
GPMC option is selected in the platform specific Kconfig.
Let's also update the description a bit, it does not mention that
enabling the debug option also disables the reset of GPMC controller
during the init as pointed out by Uwe Kleine-König
<u.kleine-koenig@pengutronix.de> and Roger Quadros <rogerq@ti.com>.
Fixes: 63aa945b10 ("memory: omap-gpmc: Add Kconfig option for debug")
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This driver makes it possible to configure the static memory
chip selects on the ARM PL172 MultiPort Memory Controller
from a set of properties in DT. Configuration of dynamic
memory is not supported and is left to the boot loader.
The intended usage is to setup timing and configuration for
static memory devices like NAND and NOR Flash before they
are probed by a driver.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
We support decoding the bootloader values if DEBUG is defined.
But we also need to change the struct omap_hwmod flags to have
HWMOD_INIT_NO_RESET to avoid the GPMC being reset during the
boot. Otherwise just the default timings will be displayed
instead of the bootloader configured timings.
This also allows us to clean up the various GPMC related
hwmod flags. For debugging, we only need HWMOD_INIT_NO_RESET,
and HWMOD_INIT_NO_IDLE is not needed.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Claudiu Beznea