Add a vendor-specific vfio_pci driver for HiSilicon ACC devices.
This will be extended in subsequent patches to add support for VFIO
live migration feature.
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20220308184902.2242-5-shameerali.kolothum.thodi@huawei.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This patch adds support for vfio_pci driver for mlx5 devices.
It uses vfio_pci_core to register to the VFIO subsystem and then
implements the mlx5 specific logic in the migration area.
The migration implementation follows the definition from uapi/vfio.h and
uses the mlx5 VF->PF command channel to achieve it.
This patch implements the suspend/resume flows.
Link: https://lore.kernel.org/all/20220224142024.147653-14-yishaih@nvidia.com
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Now that vfio_pci has been split into two source modules, one focusing on
the "struct pci_driver" (vfio_pci.c) and a toolbox library of code
(vfio_pci_core.c), complete the split and move them into two different
kernel modules.
As before vfio_pci.ko continues to present the same interface under sysfs
and this change will have no functional impact.
Splitting into another module and adding exports allows creating new HW
specific VFIO PCI drivers that can implement device specific
functionality, such as VFIO migration interfaces or specialized device
requirements.
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Link: https://lore.kernel.org/r/20210826103912.128972-14-yishaih@nvidia.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This results in less kconfig wordage and a simpler understanding of the
required "depends on" to create the menu structure.
The next patch increases the nesting level a lot so this is a nice
preparatory simplification.
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Link: https://lore.kernel.org/r/20210826103912.128972-13-yishaih@nvidia.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
If VFIO_VIRQFD is required then turn on eventfd automatically.
The majority of kconfig users of the EVENTFD use select not depends on.
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Link: https://lore.kernel.org/r/20210826103912.128972-12-yishaih@nvidia.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
zap_vma_ptes() is only available when CONFIG_MMU is set/enabled.
Without CONFIG_MMU, vfio_pci.o has build errors, so make
VFIO_PCI depend on MMU.
riscv64-linux-ld: drivers/vfio/pci/vfio_pci.o: in function `vfio_pci_mmap_open':
vfio_pci.c:(.text+0x1ec): undefined reference to `zap_vma_ptes'
riscv64-linux-ld: drivers/vfio/pci/vfio_pci.o: in function `.L0 ':
vfio_pci.c:(.text+0x165c): undefined reference to `zap_vma_ptes'
Fixes: 11c4cd07ba ("vfio-pci: Fault mmaps to enable vma tracking")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Cc: kvm@vger.kernel.org
Cc: Jason Gunthorpe <jgg@nvidia.com>
Cc: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210515190856.2130-1-rdunlap@infradead.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This driver never had any open userspace (which for VFIO would include
VM kernel drivers) that use it, and thus should never have been added
by our normal userspace ABI rules.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Message-Id: <20210326061311.1497642-2-hch@lst.de>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Compiling the nvlink stuff relies on the SPAPR_TCE_IOMMU otherwise there
are compile errors:
drivers/vfio/pci/vfio_pci_nvlink2.c:101:10: error: implicit declaration of function 'mm_iommu_put' [-Werror,-Wimplicit-function-declaration]
ret = mm_iommu_put(data->mm, data->mem);
As PPC only defines these functions when the config is set.
Previously this wasn't a problem by chance as SPAPR_TCE_IOMMU was the only
IOMMU that could have satisfied IOMMU_API on POWERNV.
Fixes: 179209fa12 ("vfio: IOMMU_API should be selected")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Message-Id: <0-v1-83dba9768fc3+419-vfio_nvlink2_kconfig_jgg@nvidia.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
In case we're running on s390 system always expose the capabilities for
configuration of zPCI devices. In case we're running on different
platform, continue as usual.
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Define a new configuration entry VFIO_PCI_ZDEV for VFIO/PCI.
When this s390-only feature is configured we add capabilities to the
VFIO_DEVICE_GET_INFO ioctl that describe features of the associated
zPCI device and its underlying hardware.
This patch is based on work previously done by Pierre Morel.
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
POWER9 Witherspoon machines come with 4 or 6 V100 GPUs which are not
pluggable PCIe devices but still have PCIe links which are used
for config space and MMIO. In addition to that the GPUs have 6 NVLinks
which are connected to other GPUs and the POWER9 CPU. POWER9 chips
have a special unit on a die called an NPU which is an NVLink2 host bus
adapter with p2p connections to 2 to 3 GPUs, 3 or 2 NVLinks to each.
These systems also support ATS (address translation services) which is
a part of the NVLink2 protocol. Such GPUs also share on-board RAM
(16GB or 32GB) to the system via the same NVLink2 so a CPU has
cache-coherent access to a GPU RAM.
This exports GPU RAM to the userspace as a new VFIO device region. This
preregisters the new memory as device memory as it might be used for DMA.
This inserts pfns from the fault handler as the GPU memory is not onlined
until the vendor driver is loaded and trained the NVLinks so doing this
earlier causes low level errors which we fence in the firmware so
it does not hurt the host system but still better be avoided; for the same
reason this does not map GPU RAM into the host kernel (usual thing for
emulated access otherwise).
This exports an ATSD (Address Translation Shootdown) register of NPU which
allows TLB invalidations inside GPU for an operating system. The register
conveniently occupies a single 64k page. It is also presented to
the userspace as a new VFIO device region. One NPU has 8 ATSD registers,
each of them can be used for TLB invalidation in a GPU linked to this NPU.
This allocates one ATSD register per an NVLink bridge allowing passing
up to 6 registers. Due to the host firmware bug (just recently fixed),
only 1 ATSD register per NPU was actually advertised to the host system
so this passes that alone register via the first NVLink bridge device in
the group which is still enough as QEMU collects them all back and
presents to the guest via vPHB to mimic the emulated NPU PHB on the host.
In order to provide the userspace with the information about GPU-to-NVLink
connections, this exports an additional capability called "tgt"
(which is an abbreviated host system bus address). The "tgt" property
tells the GPU its own system address and allows the guest driver to
conglomerate the routing information so each GPU knows how to get directly
to the other GPUs.
For ATS to work, the nest MMU (an NVIDIA block in a P9 CPU) needs to
know LPID (a logical partition ID or a KVM guest hardware ID in other
words) and PID (a memory context ID of a userspace process, not to be
confused with a linux pid). This assigns a GPU to LPID in the NPU and
this is why this adds a listener for KVM on an IOMMU group. A PID comes
via NVLink from a GPU and NPU uses a PID wildcard to pass it through.
This requires coherent memory and ATSD to be available on the host as
the GPU vendor only supports configurations with both features enabled
and other configurations are known not to work. Because of this and
because of the ways the features are advertised to the host system
(which is a device tree with very platform specific properties),
this requires enabled POWERNV platform.
The V100 GPUs do not advertise any of these capabilities via the config
space and there are more than just one device ID so this relies on
the platform to tell whether these GPUs have special abilities such as
NVLinks.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Allow the code which provides extensions to support direct assignment
of Intel IGD (GVT-d) to be compiled out of the kernel if desired. The
config option for this was previously automatically enabled on X86,
therefore the default remains Y. This simply provides the option to
disable it even for X86.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This is the first consumer of vfio device specific resource support,
providing read-only access to the OpRegion for Intel graphics devices.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This patch adds the registration/unregistration of an
irq_bypass_producer for MSI/MSIx on vfio pci devices.
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Feng Wu <feng.wu@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
An unintended consequence of commit 42ac9bd18d ("vfio: initialize
the virqfd workqueue in VFIO generic code") is that the vfio module
is renamed to vfio_core so that it can include both vfio and virqfd.
That's a user visible change that may break module loading scritps
and it imposes eventfd support as a dependency on the core vfio code,
which it's really not. virqfd is intended to be provided as a service
to vfio bus drivers, so instead of wrapping it into vfio.ko, we can
make it a stand-alone module toggled by vfio bus drivers. This has
the additional benefit of removing initialization and exit from the
core vfio code.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
add Kconfig switch to hide INTx
add Kconfig switch to let vfio announce PCI BARs are not mapable
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
PCI defines display class VGA regions at I/O port address 0x3b0, 0x3c0
and MMIO address 0xa0000. As these are non-overlapping, we can ignore
the I/O port vs MMIO difference and expose them both in a single
region. We make use of the VGA arbiter around each access to
configure chipset access as necessary.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Add PCI device support for VFIO. PCI devices expose regions
for accessing config space, I/O port space, and MMIO areas
of the device. PCI config access is virtualized in the kernel,
allowing us to ensure the integrity of the system, by preventing
various accesses while reducing duplicate support across various
userspace drivers. I/O port supports read/write access while
MMIO also supports mmap of sufficiently sized regions. Support
for INTx, MSI, and MSI-X interrupts are provided using eventfds to
userspace.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Shameer Kolothum