Each iteration of for_each_child_of_node() puts the previous node;
however, in the case of a return from the middle of the loop, there is no
put, thus causing a memory leak. Hence put of_node_put() statements as
required before two mid-loop return statements.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190808074720.15754-1-nishkadg.linux@gmail.com
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To support pinctl hog restore after LPSR resume back,
add the generic suspend/resume in pinctrl-imx along with the
generic pm ops to be used by platform specific drivers. Then
make use of the newly added ops in i.MX8MQ platform specific
driver.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper devm_platform_ioremap_resource() which wraps the
platform_get_resource() and devm_ioremap_resource() together, to
simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The address of "ipctl->pin_regs[pin_id]" can't be NULL. It's the offset
into an array in the middle of a struct. This patch removes the check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After patch b96eea718b ("pinctrl: fsl: add scu based pinctrl support"),
NO_PAD_CTL pads map are not skipped anymore which results in
a possible memory corruption. As we actually only need to create config
maps for SCU pads and MMIO pads which are not using the default config
(a.k.a IMX_NO_PAD_CTL), so let's add a proper check before creating
the config maps. And during MMIO pads parsing, we also need update the
list_p point as SCU case to ensure the pin data next parsed is correct.
Cc: Linus Walleij <linus.walleij@linaro.org>
Fixes: b96eea718b ("pinctrl: fsl: add scu based pinctrl support")
Reported-by: Martin Kaiser <martin@kaiser.cx>
Suggested-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Martin Kaiser <martin@kaiser.cx>
Tested-by: Leonard Crestez <leonard.crestez@nxp.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some i.MX SoCs (e.g. MX8QXP and MX8QM) contain a system controller
that is responsible for controlling the pad setting of the IPs that
are present. Communication between the host processor running an OS
and the system controller happens through a SCU protocol.
This patch classifies the pad settings into two categories: MMIO and SCU.
For the original MMIO method, no functional changes except organize them
into a few imx_*_mmio() functions. Besides that, we add the SCU based
Pad Mux and Pinconf setting support which are implemented in pinctrl-scu.c.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The > should really be >= here. It's harmless because
pinctrl_generic_get_group() will return a NULL if group is invalid.
Fixes: ae75ff8145 ("pinctrl: pinctrl-imx: add imx pinctrl core driver")
Reported-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For a constant format without additional arguments, use seq_puts()
instead of seq_printf(). Also, it fixes the following checkpatch
warning.
WARNING: Prefer seq_puts to seq_printf
+ seq_printf(s, "N/A");
WARNING: Prefer seq_puts to seq_printf
+ seq_printf(s, "\n");
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current code comments of PIN_FUNC_ID actually is not true for
SHARE_MUX_CONF_REG case which should be a 4 u32 PIN_FUNC_ID.
Fix the comments and re-org it a bit for better extendibility
as we may add a different size for SCU based PIN_FUNC_ID later.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The unsigned integer nfuncs is being error checked with a value less
or equal to zero; this is always false if of_get_child_count returns a
-ve for an error condition since nfuncs is not signed. Fix this by
making variables nfuncs and i signed integers.
Detected with Coccinelle:
drivers/pinctrl/freescale/pinctrl-imx.c:620:6-12: WARNING: Unsigned
expression compared with zero: nfuncs <= 0
Cc: Linus Walleij <linus.walleij@linaro.org>
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The decode parameters are constant mark them const.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For some SoCs the struct imx_pinctrl_soc_info is passed through
of_device_id.data which is const. Most variables are already const
or otherwise not written. However, some fields are modified at
runtime. Move those fields to the dynamically allocated struct
imx_pinctrl.
Fixes: b3060044e4 ("pinctrl: freescale: imx7d: make of_device_ids const")
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Lee Jones <lee@kernel.org>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Barry Song <baohua@kernel.org>
Cc: linux-gpio@vger.kernel.org
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: kernel@stlinux.com
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-renesas-soc@vger.kernel.org
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Various IMX platforms may have different imx_pmx_ops.gpio_set_direction
implementations, so let's make it platform specific callbacks instead of
the fixed common one.
Currently only VF610 platform implements it. No function level changes.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio_request_enable/disable_free actually are not quite necessary as
standard IMX pinctrl binding already sets GPIO mux from device tree,
e.g. VF610_PAD_PTB20__GPIO_42 or MX7D_PAD_SD2_CD_B__GPIO5_IO9
No need to do it again in gpio_request_enable.
And according to Stefan:
"For all GPIO I checked in upstream device trees we assign a pinctrl
to the same node, so in all cases gpio_request_enable/disable is really
unnecessary."
So it should be safe to simply remove it.
Note that this changes semantics for Vybrid, e.g.
"The two functions have been introduced for Vybrid (through
SHARE_MUX_CONF_REG) and mux pins as GPIOs automatically when a GPIO
gets requested. The automatic mux is optional by the pinmux/gpio
subsystem semantics, and other NXP devices do not use it, instead an
explicit pinctrl node is added in the device tree to mux GPIOs where
required. Hence this change aligns Vybrid to other NXP (i.MX) devices.
Note that all upstream device tree assign proper pinctrl properties
where GPIOs are used so no change is necessary for device trees."
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fugang Duan <fugang.duan@nxp.com>
Cc: Bai Ping <ping.bai@nxp.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The generic pinmux property seems to be more suitable for IMX.
So we change to use 'pinmux' instead of 'pins'.
Cc: Bai Ping <ping.bai@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
MX7ULP MUX mode mask and shift bit is different from VF610.
Let's make it a platform specific property for the later easy of
adding MX7ULP support.
One trick in exist code that Vybrid hardcoded the config part
as 0xffff because its mux_config register BIT[15-0] are all configs
part. But it's not true in ULP, so use mux_mask instead to address
the difference.
Cc: Stefan Agner <stefan@agner.ch>
Cc: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The design is based on the exist architecture that the core will
provide a uniformed way to decode the generic pin config into platform
config register raw data according to the imx_cfg_params_decode maps
registered by platform.
Two useful macros, IMX_CFG_PARAMS_DECODE and IMX_CFG_PARAMS_DECODE_INVERT,
are created for platform to register decode map conveniently.
In order to cope with some special case, a platform specific fixup()
function is also available to use.
Note that rather than fully utilizing the generic pinconf support
provided by pinctrl core, IMX only adopts the device tree bindings
of generic pinconf. The config used in .pin_config_get[set] are raw
register data instead of generic one which makes us align the exist
using. And that's also why we cannot set pinconf_ops.is_generic.
Cc: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The original implemented debug message does not work for
SHARE_MUX_CONF_REG case. This patch fixes it.
Fixes: bf5a530971 ("pinctrl: imx: add VF610 support to imx pinctrl framework")
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If 'devm_kzalloc' fails, a NULL pointer will be dereferenced.
Return -ENOMEM instead, as done for the other memory allocation just a
few lines below.
BTW, change the 'devm_kzalloc' into a 'devm_kcalloc'.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Recent pinctrl changes to allow dynamic allocation of pins exposed one
more issue with the pinctrl pins claimed early by the controller itself.
This caused a regression for IMX6 pinctrl hogs.
Before enabling the pin controller driver we need to wait until it has
been properly initialized, then claim the hogs, and only then enable it.
To fix the regression, split the code into pinctrl_claim_hogs() and
pinctrl_enable(). And then let's require that pinctrl_enable() is always
called by the pin controller driver when ready after calling
pinctrl_register_and_init().
Depends-on: 950b0d91dc ("pinctrl: core: Fix regression caused by delayed
work for hogs")
Fixes: df61b366af26 ("pinctrl: core: Use delayed work for hogs")
Fixes: e566fc11ea ("pinctrl: imx: use generic pinctrl helpers for
managing groups")
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Mika Penttilä <mika.penttila@nextfour.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Stefan Agner <stefan@agner.ch>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Gary Bisson <gary.bisson@boundarydevices.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit df61b366af26 ("pinctrl: core: Use delayed work for hogs") caused a
regression at least with sh-pfc that is also a GPIO controller as
noted by Geert Uytterhoeven <geert@linux-m68k.org>.
As the original pinctrl_register() has issues calling pin controller
driver functions early before the controller has finished registering,
we can't just revert commit df61b366af26. That would break the drivers
using GENERIC_PINCTRL_GROUPS or GENERIC_PINMUX_FUNCTIONS.
So let's fix the issue with the following steps as a single patch:
1. Revert the late_init parts of commit df61b366af26.
The late_init clearly won't work and we have to just give up
on fixing pinctrl_register() for GENERIC_PINCTRL_GROUPS and
GENERIC_PINMUX_FUNCTIONS.
2. Split pinctrl_register() into two parts
By splitting pinctrl_register() into pinctrl_init_controller()
and pinctrl_create_and_start() we have better control over when
it's safe to call pinctrl_create().
3. Introduce a new pinctrl_register_and_init() function
As suggested by Linus Walleij <linus.walleij@linaro.org>, we
can just introduce a new function for the controllers that need
pinctrl_create() called later.
4. Convert the four known problem cases to use new function
Let's convert pinctrl-imx, pinctrl-single, sh-pfc and ti-iodelay
to use the new function to fix the issues. The rest of the drivers
can be converted later. Let's also update Documentation/pinctrl.txt
accordingly because of the known issues with pinctrl_register().
Fixes: df61b366af26 ("pinctrl: core: Use delayed work for hogs")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now using function_desc structure instead of imx_pmx_func.
Also leveraging generic functions to retrieve functions count/name/groups.
The imx_free_funcs function can be removed since it is now handled by
the core driver during unregister.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now using group_desc structure instead of imx_pin_group.
Also leveraging generic functions to retrieve groups count/name/pins.
The imx_free_pingroups function can be removed since it is now handled by
the core driver during unregister.
Finally the device tree parsing is moved after the pinctrl driver registration
since this latter initializes the radix trees.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This change is inspired from the pinctrl-single architecture.
The problem with current implementation is that it isn't possible
to add/remove functions and/or groups dynamically. The radix tree
offers an easy way to do so. The intent is to offer a follow-up
patch later that will enable the use of pinctrl nodes in dt-overlays.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Otherwise can't dynamically update fields such as ngroups which can
change over time (with a dt-overlay for instance).
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
No core changes this time. Mainly gradual improvement and
feature growth in the drivers.
New drivers:
- New driver for TI DA850/OMAP-L138/AM18XX pinconf
- The SX150x was moved over from the GPIO subsystem and
reimagined as a pin control driver with GPIO support
in a joint effort by three independent users of this
hardware. The result was amazingly good!
- New subdriver for the Oxnas OX820
Improvements:
- The sunxi driver now supports the generic pin control
bindings rather than the sunxi-specific. Add debouncing
support to the driver.
- Simplifications in pinctrl-single adding a generic parser.
- Two downstream fixes and move the Raspberry Pi BCM2835 over
to use the generic GPIOLIB_IRQCHIP.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJYTny8AAoJEEEQszewGV1zz0MP/2KLLiZtBaBo0hDfY2Oussjp
JRO/VkjFIff/iDznkJJhMFPGwQ6ebp63vNRrwwOYwGa2GyZZrbeshul3oV89fyeL
NYApweAFIOFnTI6TVb5k1cGoPJcck2OalSkwHNvPVEXYykf3xy6Jm0M81T9t8fsu
xmSAfqvue9oYgDGN3jYVzsL9U6mGdWZV5fjFzwEfl/6oMA03/CMFdkDz6OBOj9ms
addIx6fQEiS1XtIwEKnX6PS8Q78/vJ/Yl6IKow/5U5lTx5HR+nbECADdEM3jqper
jifodSzJiN6fE3C55o9uupM8tVbu9lj18bb2UVOLiFB+IVlWYKekIzG+8Jg0YvJ7
zEiLzXntNHGNM3Nvinf0AL42+Uz8Ar93AvhdZD2H4yqo6dA8ifojNnavuUa9piGR
xlV8llwgSXZF8+b0ZodSFSS4R0zSGSXSimIlWDsdJ06UWHoJU2yijmkEJicXyS23
Qlo+eK830F+e0FWHTEq+OsiFoCOrD3Zin3gfNtCKoLZpTf77YFOkF3aGMrrmoIRr
MGahrssK+B6Hr8JzHWZDLpIEUL3VB+gHm6Vj4Tt5i2Ms7rw6hB60mu14PZ1pGlY0
U9CFfYg9NSPqRrgkirlETI+l7rfvVHRxqgtMQSLE6uI1Nxw+6ubMRgB2uk92LQzv
4F3H6v/5IBGqDRA5jr7a
=Pkzu
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl updates from Linus Walleij:
"Bulk pin control changes for the v4.10 kernel cycle:
No core changes this time. Mainly gradual improvement and
feature growth in the drivers.
New drivers:
- New driver for TI DA850/OMAP-L138/AM18XX pinconf
- The SX150x was moved over from the GPIO subsystem and reimagined as
a pin control driver with GPIO support in a joint effort by three
independent users of this hardware. The result was amazingly good!
- New subdriver for the Oxnas OX820
Improvements:
- The sunxi driver now supports the generic pin control bindings
rather than the sunxi-specific. Add debouncing support to the
driver.
- Simplifications in pinctrl-single adding a generic parser.
- Two downstream fixes and move the Raspberry Pi BCM2835 over to use
the generic GPIOLIB_IRQCHIP"
* tag 'pinctrl-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (92 commits)
pinctrl: sx150x: use new nested IRQ infrastructure
pinctrl: sx150x: handle missing 'advanced' reg in sx1504 and sx1505
pinctrl: sx150x: rename 'reg_advance' to 'reg_advanced'
pinctrl: sx150x: access the correct bits in the 4-bit regs of sx150[147]
pinctrl: mt8173: set GPIO16 to usb iddig mode
pinctrl: bcm2835: switch to GPIOLIB_IRQCHIP
pinctrl: New driver for TI DA850/OMAP-L138/AM18XX pinconf
devicetree: bindings: pinctrl: Add binding for ti,da850-pupd
Documentation: pinctrl: palmas: Add ti,palmas-powerhold-override property definition
pinctrl: intel: set default handler to be handle_bad_irq()
pinctrl: sx150x: add support for sx1501, sx1504, sx1505 and sx1507
pinctrl: sx150x: sort chips by part number
pinctrl: sx150x: use correct registers for reg_sense (sx1502 and sx1508)
pinctrl: imx: fix imx_pinctrl_desc initialization
pinctrl: sx150x: support setting multiple pins at once
pinctrl: sx150x: various spelling fixes and some white-space cleanup
pinctrl: mediatek: use builtin_platform_driver
pinctrl: stm32: use builtin_platform_driver
pinctrl: sunxi: Testing the wrong variable
pinctrl: nomadik: split up and comments MC0 pins
...
Group index is incremented on every new group parsed. Since the
field is part of struct imx_pinctrl_soc_info, which is typically
a global variable passed by the individual pinctrl-imx.c based
driver, it does not get cleared automatically when re-probing the
driver. This lead imx_pinctrl_parse_functions passing a group
pointer which is outside of the allocated group space on second
probe and onwards. Typically this ended up in a NULL pointer
dereference when accessing the name field like this:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
...
PC is at strcmp+0x18/0x44
LR is at imx_dt_node_to_map+0xc4/0x290
Avoid this by setting group_index to 0 on probe.
This has been observed when using DEBUG_TEST_DRIVER_REMOVE.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While only Freescale Vybrid SoC has settings of GPIO capabilities done
by iomux controller, it is only a matter of GPIO controller driver
implementation for the rest of Freescale/NXP SoCs from iMX series.
As a practical example on GPIO request a pad function should be
switched to GPIO, but because this requires updates to all particular
iMX pinctrl drivers, for simplicity at the moment add only a proper
connection between shared pinctrl-imx and pinctrl/pinmux core, namely
.gpio_request_enable/.gpio_disable_free/.gpio_set_direction callbacks
should return success to a caller. This change allows to progress by
adding request/free callbacks into gpio-mxc.c driver.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
cat /sys/kernel/debug/pinctrl/${pinctrl}/pinconf-groups output is
hardly readable, if a pin group contains more than one pin the output
is glued and looks like this:
MX6Q_PAD_SD1_DAT0: 0x17071MX6Q_PAD_SD1_CMD: 0x17071MX6Q_PAD_SD1_CLK: 0x17071
Add two space indentation and a new line separator to improve
readability of the output.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
New drivers:
- New driver for Oxnas pin control and GPIO. This ARM-based chipset
is used in a few storage (NAS) type devices.
- New driver for the MAX77620/MAX20024 pin controller portions.
- New driver for the Intel Merrifield pin controller.
New subdrivers:
- New subdriver for the Qualcomm MDM9615
- New subdriver for the STM32F746 MCU
- New subdriver for the Broadcom NSP SoC.
Cleanups:
- Demodularization of bool compiled-in drivers.
Apart from this there is just regular incremental improvements to
a lot of drivers, especially Uniphier and PFC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=po0g
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.8 kernel cycle.
Nothing stands out as especially exiting: new drivers, new subdrivers,
lots of cleanups and incremental features.
Business as usual.
New drivers:
- New driver for Oxnas pin control and GPIO. This ARM-based chipset
is used in a few storage (NAS) type devices.
- New driver for the MAX77620/MAX20024 pin controller portions.
- New driver for the Intel Merrifield pin controller.
New subdrivers:
- New subdriver for the Qualcomm MDM9615
- New subdriver for the STM32F746 MCU
- New subdriver for the Broadcom NSP SoC.
Cleanups:
- Demodularization of bool compiled-in drivers.
Apart from this there is just regular incremental improvements to a
lot of drivers, especially Uniphier and PFC"
* tag 'pinctrl-v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (131 commits)
pinctrl: fix pincontrol definition for marvell
pinctrl: xway: fix typo
Revert "pinctrl: amd: make it explicitly non-modular"
pinctrl: iproc: Add NSP and Stingray GPIO support
pinctrl: Update iProc GPIO DT bindings
pinctrl: bcm: add OF dependencies
pinctrl: ns2: remove redundant dev_err call in ns2_pinmux_probe()
pinctrl: Add STM32F746 MCU support
pinctrl: intel: Protect set wake flow by spin lock
pinctrl: nsp: remove redundant dev_err call in nsp_pinmux_probe()
pinctrl: uniphier: add Ethernet pin-mux settings
sh-pfc: Use PTR_ERR_OR_ZERO() to simplify the code
pinctrl: ns2: fix return value check in ns2_pinmux_probe()
pinctrl: qcom: update DT bindings with ebi2 groups
pinctrl: qcom: establish proper EBI2 pin groups
pinctrl: imx21: Remove the MODULE_DEVICE_TABLE() macro
Documentation: dt: Add new compatible to STM32 pinctrl driver bindings
includes: dt-bindings: Add STM32F746 pinctrl DT bindings
pinctrl: sunxi: fix nand0 function name for sun8i
pinctrl: uniphier: remove pointless pin-mux settings for PH1-LD11
...
None of these files have anything modular in them, so they
don't need to be bringing in module.h and all its dependencies.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some PINs do not have a MUX register, it is not an error.
It is necessary to allow the continuation of the PINs configuration,
otherwise the whole PIN-group will be configured incorrectly.
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When building with 'make W=1', we get harmless warnings about
five drivers in drivers/pinctrl, which all contain a copy of
the same line:
drivers/pinctrl/freescale/pinctrl-imx1-core.c:160:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
This replaces the somewhat nonstandard 'static const inline'
with 'static inline const', which has the same meaning but
does not cause this warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To i.MX7D, there are two iomux controllers, iomuxc and iomuxc_lpsr.
They should not share one pin controller descriptor, otherwise
the value filled into imx_pinctrl_desc when probing the first
iomux controller will be overridden when probing the second one.
In this patch, discard the static allcoated imx_pinctrl_desc and
switch to dynamically allcate pin controller descriptor for each
iomux controller.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- Add the devm_pinctrl_register() API and switch all applicable drivers
to use it, saving lots of lines of code all over the place.
New drivers:
- New driver for the Broadcom NS2 SoC.
- New subdriver for the PXA25x SoCs.
- New subdriver for the AMLogic Meson GXBB SoC.
Driver improvements:
- The Intel Baytrail driver now properly supports pin control.
- The Nomadik, Rockchip, Broadcom BCM2835 supports the .get_direction() callback in
the GPIO portions.
- Continued development and stabilization of several SH-PFC
SoC subdrivers: r8a7795, r8a7790, r8a7794 etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tlvn
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This kernel cycle was quite calm when it comes to pin control and
there is really just one major change, and that is the introduction of
devm_pinctrl_register() managed resources.
Apart from that linear development, details below.
Core changes:
- Add the devm_pinctrl_register() API and switch all applicable
drivers to use it, saving lots of lines of code all over the place.
New drivers:
- driver for the Broadcom NS2 SoC
- subdriver for the PXA25x SoCs
- subdriver for the AMLogic Meson GXBB SoC
Driver improvements:
- the Intel Baytrail driver now properly supports pin control
- Nomadik, Rockchip, Broadcom BCM2835 support the .get_direction()
callback in the GPIO portions
- continued development and stabilization of several SH-PFC SoC
subdrivers: r8a7795, r8a7790, r8a7794 etc"
* tag 'pinctrl-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (85 commits)
Revert "pinctrl: tegra: avoid parked_reg and parked_bank"
pinctrl: meson: Fix eth_tx_en bit index
pinctrl: tegra: avoid parked_reg and parked_bank
pinctrl: tegra: Correctly check the supported configuration
pinctrl: amlogic: Add support for Amlogic Meson GXBB SoC
pinctrl: rockchip: fix pull setting error for rk3399
pinctrl: stm32: Implement .pin_config_dbg_show()
pinctrl: nomadik: hide nmk_gpio_get_mode when unused
pinctrl: ns2: rename pinctrl_utils_dt_free_map
pinctrl: at91: Merge clk_prepare and clk_enable into clk_prepare_enable
pinctrl: at91: Make at91_gpio_template const
pinctrl: baytrail: fix some error handling in debugfs
pinctrl: ns2: add pinmux driver support for Broadcom NS2 SoC
pinctrl: sirf/atlas7: trivial fix of spelling mistake on flagged
pinctrl: sh-pfc: Kill unused variable in sh_pfc_remove()
pinctrl: nomadik: implement .get_direction()
pinctrl: nomadik: use BIT() with offsets consequently
pinctrl: exynos5440: Use off-stack memory for pinctrl_gpio_range
pinctrl: zynq: Use devm_pinctrl_register() for pinctrl registration
pinctrl: u300: Use devm_pinctrl_register() for pinctrl registration
...
Use devm_pinctrl_register() for pin control registration and remove
need of .remove callback.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Adrian Alonso <aalonso@freescale.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On error path of_iomap() returns NULL, hence IS_ERR() check is invalid
and may cause a NULL pointer dereference, the change fixes this
problem.
While we are here invert a device node check to simplify the code.
Fixes: 26d8cde526 ("pinctrl: freescale: imx: add shared input select reg support")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit bdb0066df9 ("mfd: syscon: Decouple syscon interface from platform
devices") added the possibility to register syscon devices without
associated platform device. This also removed regmap debugfs facilities,
which don't work without a device. This patch associates the syscon regmap
that handles the IOMUX controller's general purpose registers with the
pinctrl device so that the GPR registers appear in the regmap debugfs
directory again. For example, on i.MX6Q the GPR registers now can be
read from /sys/kernel/debug/regmap/20e0000.iomuxc-gpr/registers.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Freescale Vybrid SoC has GPIO capabilities as part of the
IOMUXC. To enable GPIO's, the gpio_request_enable callback has
been implemented, however the corsponding gpio_disable_free
callback is missing. So far, disabling (unexporting) a GPIO left
the pin in its last state.
Implement a proper gpio_disable_free function which clears the
three enable bits which influence the state (IBE, OBE and PUE).
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Add shared input select register support
- imx7d has two iomux controllers iomuxc and iomuxc-lpsr
which share select_input register for daisy chain settings
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allow mux_reg offset zero to be a valid pin_id, on imx7d
mux_conf reg offset is zero for iomuxc-lspr controller
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix system chrash caused by groups whose number is smaller than the number
of groups of the last pinctl instance which is not initialized.
iMX7D supports two iomux controllers (iomuxc-lpsr and iomuxc) on probing
the second instance (iomuxc) the chrash below occurs.
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.2.0-next-20150901-00006-gebfa43c (aalonso@bluefly)
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7)
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasin instruction cache
[ 0.000000] Machine model: Freescale i.MX7 SabreSD Board
[ 0.661012] [<802a6cb0>] (strcmp) from [<802cc80c>] (imx_dt_node_to_map+0x58/0x208)
[ 0.668879] [<802cc80c>] (imx_dt_node_to_map) from [<802cbe24>] (pinctrl_dt_to_map+0x174/0x2b0)
[ 0.677654] [<802cbe24>] (pinctrl_dt_to_map) from [<802c8f18>] (pinctrl_get+0x100/0x424)
[ 0.685878] [<802c8f18>] (pinctrl_get) from [<802c9510>] (pinctrl_register+0x26c/0x480)
[ 0.694104] [<802c9510>] (pinctrl_register) from [<802ccf3c>] (imx_pinctrl_probe+0x580/0x6e8)
[ 0.702706] [<802ccf3c>] (imx_pinctrl_probe) from [<80351b58>] (platform_drv_probe+0x44/0xa4)
[ 0.711455] [<80351b58>] (platform_drv_probe) from [<803503ec>] (driver_probe_device+0x174/0x2b4)
[ 0.720405] [<803503ec>] (driver_probe_device) from [<803505fc>] (__driver_attach+0x8c/0x90)
[ 0.728982] [<803505fc>] (__driver_attach) from [<8034e930>] (bus_for_each_dev+0x6c/0xa0)
[ 0.737381] [<8034e930>] (bus_for_each_dev) from [<8034fb88>] (bus_add_driver+0x148/0x1f0)
[ 0.745804] [<8034fb88>] (bus_add_driver) from [<80350c00>] (driver_register+0x78/0xf8)
[ 0.753880] [<80350c00>] (driver_register) from [<800097d0>] (do_one_initcall+0x8c/0x1d4)
[ 0.762282] [<800097d0>] (do_one_initcall) from [<80987dac>] (kernel_init_freeable+0x144/0x1e4)
[ 0.771061] [<80987dac>] (kernel_init_freeable) from [<806d9c7c>] (kernel_init+0x8/0xe8)
[ 0.779285] [<806d9c7c>] (kernel_init) from [<8000f628>] (ret_from_fork+0x14/0x2c)
[ 0.786981] Code: e3520000 e5e32001 1afffffb e12fff1e (e4d03001)
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently, pinctrl_register() just returns NULL on error, so the
callers can not know the exact reason of the failure.
Some of the pinctrl drivers return -EINVAL, some -ENODEV, and some
-ENOMEM on error of pinctrl_register(), although the error code
might be different from the real cause of the error.
This commit reworks pinctrl_register() to return the appropriate
error code and modifies all of the pinctrl drivers to use IS_ERR()
for the error checking and PTR_ERR() for getting the error code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Lee Jones <lee@kernel.org>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Ray Jui <rjui@broadcom.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Acked-by: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Nishka Dasgupta