We are currently using nand_soft_waitrdy to poll the status of the NAND
flash. FMC2 enables the wait feature bit (this feature is mandatory for
the sequencer mode). By enabling this feature, we can't poll the status
of the NAND flash, the read status command is stucked in FMC2 pipeline
until R/B# signal is high, and locks the CPU bus.
To avoid to lock the CPU bus, we poll FMC2 ISR register. This register
reports the status of the R/B# signal.
Fixes: 2cd457f328 ("mtd: rawnand: stm32_fmc2: add STM32 FMC2 NAND flash controller driver")
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Add MTD support for the Macronix MX25R3235F SPI NOR chip from Macronix.
The chip has 4MB of total capacity, divided into a total of 64 sectors,
each 64KB sized. The chip also supports 4KB large sectors.
Additionally, it supports dual and quad read modes.
Functionality was verified on an HPE/Aruba AP-303 board.
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Intel Jasper Lake has the same SPI serial flash controller as Ice Lake.
Add Jasper Lake PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Add USE_FSR flag to all variants of n25q entries that support Flag Status
Register.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: John Garry <john.garry@huawei.com> #for n25q128a13
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Add entries for mt25q*256a and mt25q*512a flashes. These are similar to
existing n25q variants but support stateless 4 byte addressing opcodes
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
mt25q family is different from n25q family of devices, even though manf
ID and device IDs are same. mt25q flash has bit 6 set in 5th byte of
READ ID response which can be used to distinguish it from n25q variant.
mt25q flashes support stateless 4 Byte addressing opcodes where as n25q
flashes don't. Therefore, have two separate entries for mt25qu512a and
n25q512a.
Fixes: 9607af6f85 ("mtd: spi-nor: Rename "n25q512a" to "mt25qu512a (n25q512a)"")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested on the Amlogic aml-libretech-pc platform which does not support
dual or quad modes
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
[tudor.ambarus@microchip.com: order entry alphabetically]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
For GD25Q256, wrong SR bit for top/bottom selection is being used.
Fix it to use appropriate bit.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
There are some flashes to use bit 6 of status register for Top/Bottom (TB).
Use top/bottom bit variable instead of fixed value and support this case.
Set the Top/Bottom (TB) mask based on SPI_NOR_TB_SR_BIT6 flash_info flag.
We can't use a bigger granularity, for example to set TB_BIT6 per
manufacturer using a SNOR_F flag. The manufacturers don't have a common
rule in regards to the TB bit:
Winbond : Use the 6th bit from 32MB capacity
W25Q20EW, W25Q50BW, W25Q128V - TB(5)
W25Q256JV, W25M512JV - TB(6)
GigaDevice : Use the 6th bit from 32MB capacity
GD25Q16C, GD25Q32C, GD25LQ32D, GD25Q64C, GD25Q128 - TB(5)
GD25Q256 - TB(6)
Micron/STM : Keep to use 5th bit
M25PX64, N25Q128A, N25Q512A, MT25QL512ABB, MT25QL02GCBB - TB(5)
Spansion : Use the 6th bit from 16MB capacity
S25FL116K, S25FL132K, S25FL165K - TB(5)
S25FL128L, S25FL256L - TB(6)
We can't make a correlation between TB and BP3 either, i.e. assume that if
BP3 is defined then TB will be at BIT(6). Micron breaks this rule.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
[tudor.ambarus@microchip.com: describe the reason for setting a
new flash_info flag.]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Each vendor uses different bits for SR_TB of flash.
To avoid ambiguity, rename SR_TB to indicate the bit used.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The w25q256 supports 4-byte opcodes so lets add the flag.
Tested on OpenWrt under 4.19.82 kernel on 8devices Habanero.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Here is the "big" tty and serial driver patches for 5.5-rc1. It's a bit
later in the merge window than normal as I wanted to make sure some
last-minute patches applied to it were all sane. They seem to be :)
There's a lot of little stuff in here, for the tty core, and for lots of
serial drivers:
- reverts of uartlite serial driver patches that were wrong
- msm-serial driver fixes
- serial core updates and fixes
- tty core fixes
- serial driver dma mapping api changes
- lots of other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXebFIQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylnmACgjfMcfQWa7uC9Q6m2DaQaRMaW6QoAnjg+TgBB
eW9EhvyXL2VbrsuUl+iH
=Am9O
-----END PGP SIGNATURE-----
Merge tag 'tty-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the "big" tty and serial driver patches for 5.5-rc1.
It's a bit later in the merge window than normal as I wanted to make
sure some last-minute patches applied to it were all sane. They seem
to be :)
There's a lot of little stuff in here, for the tty core, and for lots
of serial drivers:
- reverts of uartlite serial driver patches that were wrong
- msm-serial driver fixes
- serial core updates and fixes
- tty core fixes
- serial driver dma mapping api changes
- lots of other tiny fixes and updates for serial drivers
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (58 commits)
Revert "serial/8250: Add support for NI-Serial PXI/PXIe+485 devices"
vcs: prevent write access to vcsu devices
tty: vt: keyboard: reject invalid keycodes
tty: don't crash in tty_init_dev when missing tty_port
serial: stm32: fix clearing interrupt error flags
tty: Fix Kconfig indentation, continued
serial: serial_core: Perform NULL checks for break_ctl ops
tty: remove unused argument from tty_open_by_driver()
tty: Fix Kconfig indentation
{tty: serial, nand: onenand}: samsung: rename to fix build warning
serial: ifx6x60: add missed pm_runtime_disable
serial: pl011: Fix DMA ->flush_buffer()
Revert "serial-uartlite: Move the uart register"
Revert "serial-uartlite: Add get serial id if not provided"
Revert "serial-uartlite: Do not use static struct uart_driver out of probe()"
Revert "serial-uartlite: Add runtime support"
Revert "serial-uartlite: Change logic how console_port is setup"
Revert "serial-uartlite: Use allocated structure instead of static ones"
tty: serial: msm_serial: Use dma_request_chan() directly for channel request
tty: serial: tegra: Use dma_request_chan() directly for channel request
...
UBI:
- Fix a regression around producing a anchor PEB for fastmap.
Due to a change in our locking fastmap was unable to produce
fresh anchors an re-used the existing one a way to often.
UBIFS:
- Fixes for endianness. A few places blindly assumed little endian.
- Fix for a memory leak in the orphan code.
- Fix for a possible crash during a commit.
- Revert a wrong bugfix.
JFFS2:
- Revert a bad bugfix in (false positive from a code checking
tool).
-----BEGIN PGP SIGNATURE-----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=LbMI
-----END PGP SIGNATURE-----
Merge tag 'upstream-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull UBI/UBIFS/JFFS2 updates from Richard Weinberger:
"This pull request contains mostly fixes for UBI, UBIFS and JFFS2:
UBI:
- Fix a regression around producing a anchor PEB for fastmap.
Due to a change in our locking fastmap was unable to produce fresh
anchors an re-used the existing one a way to often.
UBIFS:
- Fixes for endianness. A few places blindly assumed little endian.
- Fix for a memory leak in the orphan code.
- Fix for a possible crash during a commit.
- Revert a wrong bugfix.
JFFS2:
- Revert a bad bugfix (false positive from a code checking tool)"
* tag 'upstream-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
Revert "jffs2: Fix possible null-pointer dereferences in jffs2_add_frag_to_fragtree()"
ubi: Fix producing anchor PEBs
ubifs: ubifs_tnc_start_commit: Fix OOB in layout_in_gaps
ubifs: do_kill_orphans: Fix a memory leak bug
Revert "ubifs: Fix memory leak bug in alloc_ubifs_info() error path"
ubifs: Fix type of sup->hash_algo
ubifs: Fixed missed le64_to_cpu() in journal
ubifs: Force prandom result to __le32
ubifs: Remove obsolete TODO from dfs_file_write()
ubi: Fix warning static is not at beginning of declaration
ubi: Print skip_check in ubi_dump_vol_info()
As part of the cleanup of some remaining y2038 issues, I came to
fs/compat_ioctl.c, which still has a couple of commands that need support
for time64_t.
In completely unrelated work, I spent time on cleaning up parts of this
file in the past, moving things out into drivers instead.
After Al Viro reviewed an earlier version of this series and did a lot
more of that cleanup, I decided to try to completely eliminate the rest
of it and move it all into drivers.
This series incorporates some of Al's work and many patches of my own,
but in the end stops short of actually removing the last part, which is
the scsi ioctl handlers. I have patches for those as well, but they need
more testing or possibly a rewrite.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=lgCl
-----END PGP SIGNATURE-----
Merge tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground
Pull removal of most of fs/compat_ioctl.c from Arnd Bergmann:
"As part of the cleanup of some remaining y2038 issues, I came to
fs/compat_ioctl.c, which still has a couple of commands that need
support for time64_t.
In completely unrelated work, I spent time on cleaning up parts of
this file in the past, moving things out into drivers instead.
After Al Viro reviewed an earlier version of this series and did a lot
more of that cleanup, I decided to try to completely eliminate the
rest of it and move it all into drivers.
This series incorporates some of Al's work and many patches of my own,
but in the end stops short of actually removing the last part, which
is the scsi ioctl handlers. I have patches for those as well, but they
need more testing or possibly a rewrite"
* tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground: (42 commits)
scsi: sd: enable compat ioctls for sed-opal
pktcdvd: add compat_ioctl handler
compat_ioctl: move SG_GET_REQUEST_TABLE handling
compat_ioctl: ppp: move simple commands into ppp_generic.c
compat_ioctl: handle PPPIOCGIDLE for 64-bit time_t
compat_ioctl: move PPPIOCSCOMPRESS to ppp_generic
compat_ioctl: unify copy-in of ppp filters
tty: handle compat PPP ioctls
compat_ioctl: move SIOCOUTQ out of compat_ioctl.c
compat_ioctl: handle SIOCOUTQNSD
af_unix: add compat_ioctl support
compat_ioctl: reimplement SG_IO handling
compat_ioctl: move WDIOC handling into wdt drivers
fs: compat_ioctl: move FITRIM emulation into file systems
gfs2: add compat_ioctl support
compat_ioctl: remove unused convert_in_user macro
compat_ioctl: remove last RAID handling code
compat_ioctl: remove /dev/raw ioctl translation
compat_ioctl: remove PCI ioctl translation
compat_ioctl: remove joystick ioctl translation
...
Any arm config which has 'CONFIG_MTD_ONENAND_SAMSUNG=m' and
'CONFIG_SERIAL_SAMSUNG=m' gives a build warning:
warning: same module names found:
drivers/tty/serial/samsung.ko
drivers/mtd/nand/onenand/samsung.ko
Rename both drivers/tty/serial/samsung.c to
drivers/tty/serial/samsung_tty.c and drivers/mtd/nand/onenand/samsung.c
drivers/mtd/nand/onenand/samsung_mtd.c to fix the warning.
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Acked-by: Richard Weinberger <richard@nod.at>
Link: https://lore.kernel.org/r/20191117202435.28127-1-sudipm.mukherjee@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a new fastmap is about to be written UBI must make sure it has a
free block for a fastmap anchor available. For this ubi_update_fastmap()
calls ubi_ensure_anchor_pebs(). This stopped working with 2e8f08deab
("ubi: Fix races around ubi_refill_pools()"), with this commit the wear
leveling code is blocked and can no longer produce free PEBs. UBI then
more often than not falls back to write the new fastmap anchor to the
same block it was already on which means the same erase block gets
erased during each fastmap write and wears out quite fast.
As the locking prevents us from producing the anchor PEB when we
actually need it, this patch changes the strategy for creating the
anchor PEB. We no longer create it on demand right before we want to
write a fastmap, but instead we create an anchor PEB right after we have
written a fastmap. This gives us enough time to produce a new anchor PEB
before it is needed. To make sure we have an anchor PEB for the very
first fastmap write we call ubi_ensure_anchor_pebs() during
initialisation as well.
Fixes: 2e8f08deab ("ubi: Fix races around ubi_refill_pools()")
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
Compiler generates following warning when kernel is built with W=1:
drivers/mtd/ubi/ubi.h:971:1: warning: ‘static’ is not at beginning
of declaration [-Wold-style-declaration]
This commit fixes this by correctly ordering keywords.
Signed-off-by: Rishi Gupta <gupt21@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
It might be interesting, if "skip_check" is set or not, so lets print
this flag in ubi_dump_vol_info() as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Richard Weinberger <richard@nod.at>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
* Useless extra checks dropped.
* Updated the detection of the bad block markers position
Raw NAND controller drivers:
* Cadence : New driver
* Brcmnand: Support for flash-dma v0 + fixes
* Denali : Support for the legacy controller/chip DT representation
dropped
* Superfluous dev_err() calls removed
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl3KwQYACgkQJWrqGEe9
VoTj1wf/Zvnk1u2vNVUaWDaHnUTAcMvjYNr1N1ppXquRXQTknZHxcgqavcwOA3yV
inHRdjQpvTPft3Pb0tddC2VBOMQTYWDGJs6JOLiPF5c4QdW/w4yHRrdnEIumbVP/
itXySbPj2QsXcRuIoEm165NTI8mdSzZFixZvCNS58r2mvMXvQbcUHsP9vjlUs9/S
XPqBlSBPKa6hC2ToIiXhgkGDQzVJ/OkCOSgG+37ATUrEqWUi9oN2KUPkbk4HSZe9
dntUIFSjeAqGjKGRGwAlt4axhnFWABfWa9xBwX9k5s4mt/FJ9QF24geemz/F1Ljp
7xd6MJu3JYoW8qBcXRRDgHuv5RNnHA==
=rpUJ
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.5' into mtd/next
Raw NAND core
* Useless extra checks dropped.
* Updated the detection of the bad block markers position
Raw NAND controller drivers:
* Cadence : New driver
* Brcmnand: Support for flash-dma v0 + fixes
* Denali : Support for the legacy controller/chip DT representation
dropped
* Superfluous dev_err() calls removed
- introduce 'struct spi_nor_controller_ops',
- clean the Register Operations methods,
- use dev_dbg insted of dev_err for low level info,
- fix retlen handling in sst_write(),
- fix silent truncations in spi_nor_read and spi_nor_read_raw(),
- fix the clearing of QE bit on lock()/unlock(),
- rework the disabling of the block write protection,
- rework the Quad Enable methods,
- make sure nor->spimem and nor->controller_ops are mutually exclusive,
- set default Quad Enable method for ISSI flashes,
- add support for few flashes.
SPI NOR controller drivers changes:
- intel-spi:
- support chips without software sequencer,
- add support for Intel Cannon Lake and Intel Comet Lake-H flashes.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAl3Kep8ACgkQS1VPR6WN
FOn9kgf/aKPgU6LR84YpwUKRZ4S+6K1H8SdDUt8v0FYSQ6oaTjF13fApg43WDja5
Zk0l5tlX7WIvlcRC6XKPhryZTXOKWojW1X8sguPYIZGzo7q82Eyda23jkw1QptWr
VO9L/tdK4yVUbdtp6VS/FUF31PC0DtDoCzsfBSUgrZP2srFF1BtOJNUgyuDceoxo
y3hEmINDnkaOvDDl/kbJjdEHG4PV8Vi4k0KE8deLpqlp8GDG1nkTeA1Sim7WjBPA
ZZOdg9fmGI8H8+umQEnn06H4O95T2+fX+kDMCYo4RbgWyWlGv5TidgRREmC/cSbl
YEPu6LCQoUZPVEvgolr/8Akf968ZiQ==
=i15M
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-5.5' into mtd/next
SPI NOR core changes:
- introduce 'struct spi_nor_controller_ops',
- clean the Register Operations methods,
- use dev_dbg insted of dev_err for low level info,
- fix retlen handling in sst_write(),
- fix silent truncations in spi_nor_read and spi_nor_read_raw(),
- fix the clearing of QE bit on lock()/unlock(),
- rework the disabling of the block write protection,
- rework the Quad Enable methods,
- make sure nor->spimem and nor->controller_ops are mutually exclusive,
- set default Quad Enable method for ISSI flashes,
- add support for few flashes.
SPI NOR controller drivers changes:
- intel-spi:
- support chips without software sequencer,
- add support for Intel Cannon Lake and Intel Comet Lake-H flashes.
* Code cleanups related useless initializers and coding style issues
* Fix for a possible double free problem in cfi_cmdset_0002
* Improved error reporting and handling in cfi_cmdset_0002 core for HyperFlash
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEyRC2zAhGcGjrhiNExEYeRXyRFuMFAl3GhtAQHHZpZ25lc2hy
QHRpLmNvbQAKCRDERh5FfJEW4/0NB/9LJZ7CQKjQOBpxypJ9LzFcXF7KHF+xaU4G
NRDJTeAng7c034tFj2tHfsICs1epidMC7OOdKZq+AJuN3M6Iq2JtqKb19r3pfQyo
S2HGQaHwrH3K8iF8ba5MBtax0xncipQgQgIAPgWZ80MdJWZKLh1F5hqhDyrO/LBR
vYG4TLmOJk5Chro5PtRytOQV/i+1VfSS7R7zleTDtCGH3pMbFOU9ySac1pDQfNmR
b36RRt119Vs6V80Sb+3L8AFfYCIcNwFySmzWJGPgmrdruTRUIeQ3II6M2HSMEYbO
oUTzxFDOTuBGrBLa3Rsq0Z9OhZk1WQqOC1f6mmfjRz/FdqiJBTXs
=K6bc
-----END PGP SIGNATURE-----
Merge CFI/Hyperbus tag 'for-v5.5-rc1' into mtd/next
CFI core changes:
* Code cleanups related useless initializers and coding style issues
* Fix for a possible double free problem in cfi_cmdset_0002
* Improved error reporting and handling in cfi_cmdset_0002 core for HyperFlash
Due to the use of sizeof(), command size set for the spi transfer
was wrong. Driver was sending and receiving always 1 byte less
and especially on write, it was hanging.
echo -n -e "\\x1\\x2\\x3\\x4" > /dev/mtd1
And read part too now works as expected.
hexdump -C -n16 /dev/mtd1
00000000 01 02 03 04 ab f3 ad c2 ab e3 f4 36 dd 38 04 15
00000010
Fixes: 4379075a87 ("mtd: mchp23k256: Add support for mchp23lcv1024")
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Cc: linux-mtd@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Set the default Quad Enable method for ISSI flashes. Used for
ISSI flashes (IS25WP256D-JMLE) that do not support SFDP tables
and can not determine the Quad Enable method by parsing BFPT.
Based on code originally written by Wesley Terpstra <wesley@sifive.com>
and/or Palmer Dabbelt <palmer@sifive.com>
c94e267766
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
[tudor.ambarus@microchip.com:
- rebase, split and adapt for latest spi-nor/next,
- use PMC CFI ID for ISSI. According to JEP106BA, "Programmable Micro Corp"
changed its name to Integrated Silicon Solution (ISSI)]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Update the spi_nor_id table for is25wp256 (32MB) device from ISSI,
present on HiFive Unleashed dev board (Rev: A00).
Use the post bfpt fixup hook for the is25wp256 device, as done for
the is25lp256 device to overwrite the wrong address width advertised
by BFPT.
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
[tudor.ambarus@microchip.com: rebase, split and adapt for latest spi-nor/next]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Add MTD support for w25q256jw SPI NOR chip from Winbond. This chip
supports dual/quad I/O mode with 512 blocks of memory organized in
64KB sectors. In addition to this, there is also small 4KB sectors
available for flexibility. The device has been validated using Thor96
board.
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Darshak Patel <darshak.patel@einfochips.com>
[Mani: cleaned up for upstream]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
When the controller is not under the SPI-MEM interface it may implement
the optional controller_ops->erase() method.
nor->spimem and nor->controller_ops are mutually exclusive. Move the
nor->controller_ops->erase != NULL check as an 'else if' case to
nor->spimem, in order to avoid the nor->controller_ops != NULL
check.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Expand the spi_nor_check() to make sure that nor->spimem and
nor->controller_ops are mutually exclusive.
Fixes: b35b9a1036 ("mtd: spi-nor: Move m25p80 code in spi-nor.c")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Rename macronix_quad_enable() to a generic name:
spi_nor_sr1_bit6_quad_enable().
Prepend "spi_nor_" to "sr2_bit7_quad_enable". All SPI NOR generic
methods should be prepended by "spi_nor_".
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Merge
spansion_no_read_cr_quad_enable()
spansion_read_cr_quad_enable()
into
spi_nor_sr2_bit1_quad_enable().
Reduce code duplication by introducing spi_nor_write_16bit_cr_and_check().
The Configuration Register contains bits that can be updated in future:
FREEZE, CMP. Provide a generic method that allows updating all bits
of the Configuration Register.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
JEDEC Basic Flash Parameter Table, 15th DWORD, bits 22:20,
refers to this bit as "bit 1 of the status register 2".
Rename the macro accordingly.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Test that all the bits from Status Register 1 and Status Register 2
were written correctly.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
spi_nor_unlock() unlocks blocks of memory or the entire flash memory
array, if requested. clear_sr_bp() unlocks the entire flash memory
array at boot time. This calls for some unification, clear_sr_bp() is
just an optimization for the case when the unlock request covers the
entire flash size.
Get rid of clear_sr_bp() and introduce spi_nor_unlock_all(), which is
just a call to spi_nor_unlock() for the entire flash memory array.
This fixes a bug that was present in spi_nor_spansion_clear_sr_bp().
When the QE bit was zero, we used the Write Status (01h) command with
one data byte, which might cleared the Status Register 2. We now always
use the Write Status (01h) command with two data bytes when
SNOR_F_HAS_16BIT_SR is set, to avoid clearing the Status Register 2.
The SNOR_F_NO_READ_CR case is treated as well. When the flash doesn't
support the CR Read command, we make an assumption about the value of
the QE bit. In spi_nor_init(), call spi_nor_quad_enable() first, then
spi_nor_unlock_all(), so that at the spi_nor_unlock_all() time we can
be sure the QE bit has value one, because of the previous call to
spi_nor_quad_enable().
Get rid of the MFR handling and implement specific manufacturer
default_init() fixup hooks.
Note that this changes a bit the logic for the SNOR_MFR_ATMEL,
SNOR_MFR_INTEL and SNOR_MFR_SST cases. Before this patch, the Atmel,
Intel and SST chips did not set the locking ops, but unlocked the entire
flash at boot time, while now they are setting the locking ops to
stm_locking_ops. This should work, since the disable of the block
protection at the boot time used the same Status Register bits to unlock
the flash, as in the stm_locking_ops case.
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Make sure that when doing a lock() or an unlock() operation we don't clear
the QE bit from Status Register 2.
JESD216 revB or later offers information about the *default* Status
Register commands to use (see BFPT DWORDS[15], bits 22:20). In this
standard, Status Register 1 refers to the first data byte transferred on a
Read Status (05h) or Write Status (01h) command. Status register 2 refers
to the byte read using instruction 35h. Status register 2 is the second
byte transferred in a Write Status (01h) command.
Industry naming and definitions of these Status Registers may differ.
The definitions are described in JESD216B, BFPT DWORDS[15], bits 22:20.
There are cases in which writing only one byte to the Status Register 1
has the side-effect of clearing Status Register 2 and implicitly the Quad
Enable bit. This side-effect is hit just by the
BFPT_DWORD15_QER_SR2_BIT1_BUGGY and BFPT_DWORD15_QER_SR2_BIT1 cases.
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
The commit 4844ef8030 ("mtd: cfi_cmdset_0002: Add support for polling
status register") added checking for the status register error bits into
chip_good() to only return 1 if these bits are 0s. Unfortunately, this
means that polling using chip_good() always reaches a timeout condition
when erase or program failure bits are set. Let's fully delegate the task
of determining the error conditions to cfi_check_err_status() and make
chip_good() only look for the Device Ready/Busy condition.
Fixes: 4844ef8030 ("mtd: cfi_cmdset_0002: Add support for polling status register")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Cypress S26K{L|S}P{128|256|512}S datasheet says that the error bits in
the status register are only valid when the "device ready" bit 7 is set.
Add the check for the device ready bit in cfi_check_err_status() as that
function isn't always called with this bit set.
Fixes: 4844ef8030 ("mtd: cfi_cmdset_0002: Add support for polling status register")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Else there may be a double-free problem, because cfi->cfiq will
be freed by mtd_do_chip_probe() if both the two invocations of
check_cmd_set() return failure.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The 'ret' local variables are typically initialized to 0 but this value is
often unused, thus we can kill those initializers.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Use DIV_ROUND_UP() in cfi_udelay() instead of open-coding it...
Doing this also helpfully gets rid of two complaints from
'scripts/checkpatch.pl --strict':
CHECK: spaces preferred around that '+' (ctx:VxV)
#29: FILE: drivers/mtd/chips/cfi_util.c:29:
+ msleep((us+999)/1000);
^
CHECK: spaces preferred around that '/' (ctx:VxV)
#29: FILE: drivers/mtd/chips/cfi_util.c:29:
+ msleep((us+999)/1000);
^
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Check that all the bits written in the write_sr_and_check() method
match the status_new received value. Failing to write the other bits
is dangerous too, extend the check.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
When the Read-Modify-Write-Read-Back Quad Enable methods failed on
the Read-Back, they returned -EINVAL. Since this is an I/O error,
return -EIO.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Drop the default spansion_quad_enable() method and replace it with
spansion_read_cr_quad_enable().
The function was buggy, it didn't care about the previous values
of the Status and Configuration Registers. spansion_read_cr_quad_enable()
is a Read-Modify-Write-Check function that keeps track of what were
the previous values of the Status and Configuration Registers.
In terms of instruction types sent to the flash, the only difference
between the spansion_quad_enable() and spansion_read_cr_quad_enable()
is that the later calls spi_nor_read_sr(). We can safely assume that all
flashes support spi_nor_read_sr(), because all flashes call it in
spi_nor_sr_ready(). The transition from spansion_quad_enable() to
spansion_read_cr_quad_enable() will not affect anybody, drop the buggy
code.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Merge
static int spi_nor_write_sr(struct spi_nor *nor, u8 val)
static int spi_nor_write_sr_cr(struct spi_nor *nor, const u8 *sr_cr)
into
static int spi_nor_write_sr(struct spi_nor *nor, const u8 *sr, size_t len)
The Status Register can be written with one or two bytes. Merge
the two functions to avoid code duplication.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Avoid duplicating code by moving the calls to spi_nor_write_enable() and
spi_nor_wait_till_ready() inside the Write Status Register methods.
Move spi_nor_write_sr() to avoid forward declaration of
spi_nor_wait_till_ready().
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
spi_nor_clear_sr() and spi_nor_clear_fsr() are called just in case
of errors. The callers didn't check their return value, make them
of type void.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Rename 'sst_write_err' label to 'out' as it is no longer generic for
all the errors in the sst_write() method, and may introduce confusion.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Check for the return vales of each Register Operation.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
What most users care about is "my dev is not working properly".
All low level information should be discovered when activating
the debug traces.
Keep error messages just for the following cases:
- when the SR/FSR report program or erase fails, or attempts of
modifying a protected sector,
- when the JEDEC ID is not recognized,
- when the resume() call fails,
- when the spi_nor_check() fails.
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
spi_nor_read_raw() assigns the result of 'ssize_t spi_nor_read_data()'
to the 'int ret' variable, while 'ssize_t' is a 64-bit type and *int*
is a 32-bit type on the 64-bit machines. This silent truncation isn't
really valid, so fix up the variable's type.
Fixes: f384b352cb ("mtd: spi-nor: parse Serial Flash Discoverable Parameters (SFDP) tables")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
spi_nor_read() assigns the result of 'ssize_t spi_nor_read_data()'
to the 'int ret' variable, while 'ssize_t' is a 64-bit type and *int*
is a 32-bit type on the 64-bit machines. This silent truncation isn't
really valid, so fix up the variable's type.
Fixes: 59451e1233 ("mtd: spi-nor: change return value of read/write")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Intel Comet Lake-H PCH has the same SPI serial flash controller as Comet
Lake-LP. Add Comet Lake-H PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Print identifying information about struct device.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Constify the data to write to the Status Register.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
In case the write of the first byte failed, retlen was incorrectly
incremented to *retlen += actual; on the exit path. retlen should be
incremented when actual data was written to the flash.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Drop the error messages from the callers, since the callees
already print an error message in case of failure.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Let the callers pass the pointer to the DMA-able buffer where
the value of the Configuration Register will be written. This way we
avoid the casts between int and u8, which can be confusing.
Callers stop compare the return value of spi_nor_read_cr() with negative,
spi_nor_read_cr() returns 0 on success and -errno otherwise.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Let the callers pass the pointer to the DMA-able buffer where
the value of the Flag Status Register will be written. This way we
avoid the casts between int and u8, which can be confusing.
Caller stops compare the return value of spi_nor_read_fsr() with negative,
spi_nor_read_fsr() returns 0 on success and -errno otherwise.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Let the callers pass the pointer to the DMA-able buffer where
the value of the Status Register will be written. This way we
avoid the casts between int and u8, which can be confusing.
Callers stop compare the return value of spi_nor_read_sr() with negative,
spi_nor_read_sr() returns 0 on success and -errno otherwise.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Do not overwrite the error numbers received the Register Operations
methods.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
spi_mem_exec_op()
nor->controller_ops->write_reg()
nor->controller_ops->read_reg()
spi_nor_wait_till_ready()
Return 0 on success, -errno otherwise.
Stop compare with negative and compare with zero in all the register
operations methods.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Group all register methods up in the file, to avoid forward
declarations.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Two new lines, one after another, drop one.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
All the core functions should begin with "spi_nor_".
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Remove unecessary checking if dmac is NULL.
If Cadence nand controller driver uses DMA engine then cdns_ctrl->dmac
cannot be NULL. It is verified during driver initialization.
If Cadence nand controller driver does not use DMA engine then
CPU IO read/write are executed instead of slave DMA transfer.
In that case cdns_ctrl->dmac is not used at all.
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
platform_get_irq() will call dev_err() itself on failure,
so there is no need for the driver to also do this.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
platform_get_irq() will call dev_err() itself on failure,
so there is no need for the driver to also do this.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Sparse complained about the following:
drivers/mtd/nand/raw/brcmnand/brcmnand.c:921:40: warning: Using plain integer as NULL pointer
fix this issue by assigning the pointer to NULL.
Fixes: c1ac2dc34b ("mtd: rawnand: brcmnand: When oops in progress use pio and interrupt polling")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Commit d8e8fd0ebf ("mtd: rawnand: denali: decouple controller and
NAND chips") supported the new binding for the separate controller/chip
representation, keeping the backward compatibility.
All the device trees in upstream migrated to the new binding.
Remove the support for the old binding.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Any write with either dd or flashcp to a device driven by the
spear_smi.c driver will pass through the spear_smi_cpy_toio()
function. This function will get called for chunks of up to 256 bytes.
If the amount of data is smaller, we may have a problem if the data
length is not 4-byte aligned. In this situation, the kernel panics
during the memcpy:
# dd if=/dev/urandom bs=1001 count=1 of=/dev/mtd6
spear_smi_cpy_toio [620] dest c9070000, src c7be8800, len 256
spear_smi_cpy_toio [620] dest c9070100, src c7be8900, len 256
spear_smi_cpy_toio [620] dest c9070200, src c7be8a00, len 256
spear_smi_cpy_toio [620] dest c9070300, src c7be8b00, len 233
Unhandled fault: external abort on non-linefetch (0x808) at 0xc90703e8
[...]
PC is at memcpy+0xcc/0x330
The above error occurs because the implementation of memcpy_toio()
tries to optimize the number of I/O by writing 4 bytes at a time as
much as possible, until there are less than 4 bytes left and then
switches to word or byte writes.
Unfortunately, the specification states about the Write Burst mode:
"the next AHB Write request should point to the next
incremented address and should have the same size (byte,
half-word or word)"
This means ARM architecture implementation of memcpy_toio() cannot
reliably be used blindly here. Workaround this situation by update the
write path to stick to byte access when the burst length is not
multiple of 4.
Fixes: f18dbbb1bf ("mtd: ST SPEAr: Add SMI driver for serial NOR flash")
Cc: Russell King <linux@armlinux.org.uk>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
In order to support device tree probing of IXP4xx NOR flash
chips, a certain big-endian or mixed-endian memory access
pattern need to be used.
I have opted to use the pattern set by previous plug-ins
to physmap for Gemini and Versatile, just override some
functions and reuse most of the physmap core code as it
is to minimize maintenance.
Parts of drivers/mtd/ixp4xx.c are copied into this file.
After we have IXP4xx converted fully to device tree, the
drivers/mtd/ixp4xx.c file will be deleted and this will
be the only access pattern to the IXP4xx flash.
I did not keep the quirk in the flash write function
after probe, where the old code for a while checks for
access to odd addresses, fails and assigns a "faster"
write function once it has convinced probe to only use
2-byte accesses. As we mandate that this device should
be using bank-width = <2> this should not be a problem
unless misconfigured.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Avoid printing the address of l440gx_map.virt every time l440gx init.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Each of these drivers has a copy of the same trivial helper function to
convert the pointer argument and then call the native ioctl handler.
We now have a generic implementation of that, so use it.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Reviewed-by: Jiri Kosina <jkosina@suse.cz>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
n_tx was never used, drop it. Replace 'const u8 *txbuf' with 'u8 opcode',
to comply with the SPI NOR int (*read_reg)() method. The 'const'
qualifier has no meaning for parameters passed by value, drop it.
Going furher, the opcode was passed to cqspi_calc_rdreg() and never used,
drop it.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Move all SPI NOR controller driver specific ops in a dedicated
structure. 'struct spi_nor' becomes lighter.
Use size_t for lengths in 'int (*write_reg)()' and 'int (*read_reg)()'.
Rename wite/read_buf to buf, the name of the functions are
suggestive enough. Constify buf in int (*write_reg). Comply with these
changes in the SPI NOR controller drivers.
Suggested-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
The pointer to 'struct spi_nor' is kzalloc'ed above in the code.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Some flash controllers don't have a software sequencer. Avoid
configuring the register addresses for it, and double check
everywhere that its not accidentally trying to be used.
Every use of `sregs` is now guarded by a check of `sregs` or
`swseq_reg`. The check might be done in the calling function.
Signed-off-by: Jethro Beekman <jethro@fortanix.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The 'region' field in struct stfsm is unused and can be removed.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Most of the time the ooboffs parameter of the mtd_oob_ops structure
was initialized only when needed. Since the introduction of the
SPI-NAND subsystem, this parameter is transferred into
nand_page_io_req structure automatically and may be used by any
SPI-NAND user.
Before this happens, initialize all the structure parameters when they
are created in mtdchar.c.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/mtd/devices/spear_smi.c: In function spear_smi_probe_config_dt:
drivers/mtd/devices/spear_smi.c:780:32: warning: variable flash_info set but not used [-Wunused-but-set-variable]
It is not used since commit 6551ab5d30 ("mtd:
add device-tree support to spear_smi")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Commit 7e534323c4 ("mtd: rawnand: Pass a nand_chip object to
chip->read_xxx() hooks") modified the prototype of the struct nand_chip
read_buf function pointer. In the au1550nd driver we have 2
implementations of read_buf. The previously mentioned commit modified
the au_read_buf() implementation to match the function pointer, but not
au_read_buf16(). This results in a compiler warning for MIPS
db1xxx_defconfig builds:
drivers/mtd/nand/raw/au1550nd.c:443:57:
warning: pointer type mismatch in conditional expression
Fix this by updating the prototype of au_read_buf16() to take a struct
nand_chip pointer as its first argument, as is expected after commit
7e534323c4 ("mtd: rawnand: Pass a nand_chip object to chip->read_xxx()
hooks").
Note that this shouldn't have caused any functional issues at runtime,
since the offset of the struct mtd_info within struct nand_chip is 0
making mtd_to_nand() effectively a type-cast.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 7e534323c4 ("mtd: rawnand: Pass a nand_chip object to chip->read_xxx() hooks")
Cc: stable@vger.kernel.org # v4.20+
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add new Cadence NAND driver to MTD subsystem
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Change calculating of position page containing BBM
If none of BBM flags are set then function nand_bbm_get_next_page
reports EINVAL. It causes that BBM is not read at all during scanning
factory bad blocks. The result is that the BBT table is build without
checking factory BBM at all. For Micron flash memories none of these
flags are set if page size is different than 2048 bytes.
Address this regression by:
- adding NAND_BBM_FIRSTPAGE chip flag without any condition. It solves
issue only for Micron devices.
- changing the nand_bbm_get_next_page_function. It will return 0
if no of BBM flag is set and page parameter is 0. After that modification
way of discovering factory bad blocks will work similar as in kernel
version 5.1.
Cc: stable@vger.kernel.org
Fixes: f90da7818b (mtd: rawnand: Support bad block markers in first, second or last page)
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
- boot_mem_map is removed, providing a nice cleanup made possible by the
recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs or
MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of Vincenzo
Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic SoCs.
- pte_special() is now supported for some configurations, allowing among
other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil, mostly
enabled by the inclusion of the new TCU (timer-counter unit) drivers
he's spent a very patient year or so working on. Plus some fixes for
X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXYaqpRUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN2JUQD+PQGFIlq9bo/3vLyqsXJffm+DhwVQ
4WSCSeN5brPkO8EA/153sRJBlRtG+KK5p9f7WYKUuBfbcEawuc1uwmKuy7cG
=lWlM
-----END PGP SIGNATURE-----
Merge tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Paul Burton:
"Main MIPS changes:
- boot_mem_map is removed, providing a nice cleanup made possible by
the recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs
or MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of
Vincenzo Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic
SoCs.
- pte_special() is now supported for some configurations, allowing
among other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil,
mostly enabled by the inclusion of the new TCU (timer-counter unit)
drivers he's spent a very patient year or so working on. Plus some
fixes for X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems"
* tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (89 commits)
MIPS: Detect bad _PFN_SHIFT values
MIPS: Disable pte_special() for MIPS32 with RiXi
MIPS: ralink: deactivate PCI support for SOC_MT7621
mips: compat: vdso: Use legacy syscalls as fallback
MIPS: Drop Loongson _CACHE_* definitions
MIPS: tlbex: Remove cpu_has_local_ebase
MIPS: tlbex: Simplify r3k check
MIPS: Select R3k-style TLB in Kconfig
MIPS: PCI: refactor ioc3 special handling
mips: remove ioremap_cachable
mips/atomic: Fix smp_mb__{before,after}_atomic()
mips/atomic: Fix loongson_llsc_mb() wreckage
mips/atomic: Fix cmpxchg64 barriers
MIPS: Octeon: remove duplicated include from dma-octeon.c
firmware: bcm47xx_nvram: Allow COMPILE_TEST
firmware: bcm47xx_nvram: Correct size_t printf format
MIPS: Treat Loongson Extensions as ASEs
MIPS: Remove dev_err() usage after platform_get_irq()
MIPS: dts: mscc: describe the PTP ready interrupt
MIPS: dts: mscc: describe the PTP register range
...
UBI:
- Be less stupid when placing a fastmap anchor
- Try harder to get an empty PEB in case of contention
- Make ubiblock to warn if image is not a multiple of 512
UBIFS:
- Various fixes in error paths
JFFS2:
- Various fixes in error paths
-----BEGIN PGP SIGNATURE-----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=ptT1
-----END PGP SIGNATURE-----
Merge tag 'upstream-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull UBI, UBIFS and JFFS2 updates from Richard Weinberger:
"UBI:
- Be less stupid when placing a fastmap anchor
- Try harder to get an empty PEB in case of contention
- Make ubiblock to warn if image is not a multiple of 512
UBIFS:
- Various fixes in error paths
JFFS2:
- Various fixes in error paths"
* tag 'upstream-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
jffs2: Fix memory leak in jffs2_scan_eraseblock() error path
jffs2: Remove jffs2_gc_fetch_page and jffs2_gc_release_page
jffs2: Fix possible null-pointer dereferences in jffs2_add_frag_to_fragtree()
ubi: block: Warn if volume size is not multiple of 512
ubifs: Fix memory leak bug in alloc_ubifs_info() error path
ubifs: Fix memory leak in __ubifs_node_verify_hmac error path
ubifs: Fix memory leak in read_znode() error path
ubi: ubi_wl_get_peb: Increase the number of attempts while getting PEB
ubi: Don't do anchor move within fastmap area
ubifs: Remove redundant assignment to pointer fname
MTD core changes:
- add debugfs nodes for querying the flash name and id
- mtd parser reorganization
SPI NOR core changes:
- always use bounce buffer for register read/writes
- move m25p80 code in spi-nor.c
- rework hwcaps selection for the spi-mem case
- rework the core in order to move the manufacturer specific code
out of it:
- regroup flash parameters in 'struct spi_nor_flash_parameter'
- add default_init() and post_sfdp() hooks to tweak the flash
parameters
- introduce the ->set_4byte(), ->convert_addr() and ->setup()
methods, to deal with manufacturer specific code
- rework the SPI NOR lock/unlock logic
- fix an error code in spi_nor_read_raw()
- fix a memory leak bug
- enable the debugfs for the partname and partid
- add support for few flashes
SPI NOR controller drivers changes:
- intel-spi:
- Whitelist 4B read commands
- Add support for Intel Tiger Lake SPI serial flash
- aspeed-smc: Add of_node_put()
- hisi-sfc: Add of_node_put()
- cadence-quadspi: Fix QSPI RCU Schedule Stall
NAND core:
- Fixing typos
- Adding missing of_node_put() in various drivers
Raw NAND controller drivers:
- Macronix: new controller driver
- Omap2: Fixing the number of bitflips returned
- Brcmnand: Fix a pointer not iterating over all the page chunks
- W90x900: Driver removed
- Onenand: Fix a memory leak
- Sharpsl: Missing include guard
- STM32: Avoid warnings when building with W=1
- Ingenic: Fix a coccinelle warning
- r852: Call a helper to simplify the code
CFI core:
- Kill useless initializer in mtd_do_chip_probe()
- Fix a rare write failure seen on some cfi_cmdset_0002 compliant
Parallel NORs
- Bunch of cleanups for cfi_cmdset_0002 driver's write functions by
Tokunori Ikegami <ikegami.t@gmail.com>
-----BEGIN PGP SIGNATURE-----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=fMNy
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Richard Weinberger:
"MTD core changes:
- add debugfs nodes for querying the flash name and id
- mtd parser reorganization
SPI NOR core changes:
- always use bounce buffer for register read/writes
- move m25p80 code in spi-nor.c
- rework hwcaps selection for the spi-mem case
- rework the core in order to move the manufacturer specific code out
of it:
- regroup flash parameters in 'struct spi_nor_flash_parameter'
- add default_init() and post_sfdp() hooks to tweak the flash
parameters
- introduce the ->set_4byte(), ->convert_addr() and ->setup()
methods, to deal with manufacturer specific code
- rework the SPI NOR lock/unlock logic
- fix an error code in spi_nor_read_raw()
- fix a memory leak bug
- enable the debugfs for the partname and partid
- add support for few flashes
SPI NOR controller drivers changes:
- intel-spi:
- Whitelist 4B read commands
- Add support for Intel Tiger Lake SPI serial flash
- aspeed-smc: Add of_node_put()
- hisi-sfc: add of_node_put()
- cadence-quadspi: Fix QSPI RCU Schedule Stall
NAND core:
- Fixing typos
- Adding missing of_node_put() in various drivers
Raw NAND controller drivers:
- Macronix: new controller driver
- Omap2: fix the number of bitflips returned
- Brcmnand: fix a pointer not iterating over all the page chunks
- W90x900: driver removed
- Onenand: fix a memory leak
- Sharpsl: missing include guard
- STM32: avoid warnings when building with W=1
- Ingenic: fix a coccinelle warning
- r852: call a helper to simplify the code
CFI core:
- Kill useless initializer in mtd_do_chip_probe()
- Fix a rare write failure seen on some cfi_cmdset_0002 compliant
Parallel NORs
- Bunch of cleanups for cfi_cmdset_0002 driver's write functions by
Tokunori Ikegami"
* tag 'mtd/for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (77 commits)
mtd: pmc551: Remove set but not used variable 'soff_lo'
mtd: cfi_cmdset_0002: Fix do_erase_chip() to get chip as erasing mode
mtd: sm_ftl: Fix memory leak in sm_init_zone() error path
mtd: parsers: Move CMDLINE parser
mtd: parsers: Move OF parser
mtd: parsers: Move BCM63xx parser
mtd: parsers: Move BCM47xx parser
mtd: parsers: Move TI AR7 parser
mtd: pismo: Simplify getting the adapter of a client
mtd: phram: Module parameters add writable permissions
mtd: pxa2xx: Use ioremap_cache insted of ioremap_cached
mtd: spi-nor: Rename "n25q512a" to "mt25qu512a (n25q512a)"
mtd: spi-nor: Add support for mt35xu02g
mtd: rawnand: omap2: Fix number of bitflips reporting with ELM
mtd: rawnand: brcmnand: Fix ecc chunk calculation for erased page bitfips
mtd: spi-nor: remove superfluous pass of nor->info->sector_size
mtd: spi-nor: enable the debugfs for the partname and partid
mtd: mtdcore: add debugfs nodes for querying the flash name and id
mtd: spi-nor: hisi-sfc: Add of_node_put() before break
mtd: spi-nor: aspeed-smc: Add of_node_put()
...
Pull misc mount API conversions from Al Viro:
"Conversions to new API for shmem and friends and for mount_mtd()-using
filesystems.
As for the rest of the mount API conversions in -next, some of them
belong in the individual trees (e.g. binderfs one should definitely go
through android folks, after getting redone on top of their changes).
I'm going to drop those and send the rest (trivial ones + stuff ACKed
by maintainers) in a separate series - by that point they are
independent from each other.
Some stuff has already migrated into individual trees (NFS conversion,
for example, or FUSE stuff, etc.); those presumably will go through
the regular merges from corresponding trees."
* 'work.mount2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vfs: Make fs_parse() handle fs_param_is_fd-type params better
vfs: Convert ramfs, shmem, tmpfs, devtmpfs, rootfs to use the new mount API
shmem_parse_one(): switch to use of fs_parse()
shmem_parse_options(): take handling a single option into a helper
shmem_parse_options(): don't bother with mpol in separate variable
shmem_parse_options(): use a separate structure to keep the results
make shmem_fill_super() static
make ramfs_fill_super() static
devtmpfs: don't mix {ramfs,shmem}_fill_super() with mount_single()
vfs: Convert squashfs to use the new mount API
mtd: Kill mount_mtd()
vfs: Convert jffs2 to use the new mount API
vfs: Convert cramfs to use the new mount API
vfs: Convert romfs to use the new mount API
vfs: Add a single-or-reconfig keying to vfs_get_super()
Pull vfs mount API infrastructure updates from Al Viro:
"Infrastructure bits of mount API conversions.
The rest is more of per-filesystem updates and that will happen
in separate pull requests"
* 'work.mount-base' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
mtd: Provide fs_context-aware mount_mtd() replacement
vfs: Create fs_context-aware mount_bdev() replacement
new helper: get_tree_keyed()
vfs: set fs_context::user_ns for reconfigure
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/mtd/devices/pmc551.c: In function pmc551_erase:
drivers/mtd/devices/pmc551.c:142:15: warning: variable soff_lo set but not used [-Wunused-but-set-variable]
drivers/mtd/devices/pmc551.c: In function pmc551_read:
drivers/mtd/devices/pmc551.c:232:15: warning: variable soff_lo set but not used [-Wunused-but-set-variable]
drivers/mtd/devices/pmc551.c: In function pmc551_write:
drivers/mtd/devices/pmc551.c:289:15: warning: variable soff_lo set but not used [-Wunused-but-set-variable]
It is not used since commit cdf0a7d169 ("[MTD]
pmc551 whitespace cleanup")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
The chip state is set to erasing by the function after getting chip.
So it should be to get chip as erasing mode at first.
But previously it was to get chip as writing mode then fix as erasing.
Signed-off-by: Tokunori Ikegami <ikegami.t@gmail.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Richard Weinberger <richard@nod.at>
Christophe Kerello