We don't need variable cmd_cfg_timeout, so remove it and simplify the
code a little.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Centralize setting data->bytes_xfered in one place and make sure
that the number of transfererd bytes is set only if we receive
the end-of-chain interrupt and there was no error.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Response reading can be slightly improved by doing it in just one place.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Simplify the code by using two variables instead of a struct sd_emmc_desc.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Replace cmd->data with a local variable to simplify code a little.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
The variables holding the configuration bits are zero-initialized.
So we can remove all bit resets.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
If we don't select a set of better parameters for our emmc host,
It may easily occur CMD response CRC error. And also it may cause
cannot boot up issue.
Fot getting a set of better parameters, our emmc host supports
data tune mechanism.Therefore, our emmc driver also should change
to use data tune for CMD line.
Because our emmc host use the different clock source to sample the
CMD signal between HS200 and HS400 mode, the parameters are also
different between these two modes.
Separate cmd internal delay for HS200/HS400 mode.
This change can fix "System can not boot up" issue.
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current code gets number of taps only once and keeps the value. This is
not correct, we need to obtain it every time before executing tuning,
so remove the outer if-block.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
[wsa: extracted from a larger patch and reworded commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the (maybe academical) case, we don't get a DATAEND interrupt after
DMA completed, we will wait endlessly for the completion to complete.
This is not bad per se, since we have a more generic completion tracking
a timeout. In that rare case, however, the DMA buffer will not get
unmapped and we have a leak. Reorder the code, so unmapping will always
take place.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move a function to avoid having to forward declare it in a subsequent
patch.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
The suspend / resume callbacks lack the flexibility to allow a device to
specify a different function entirely. Change them around so that device
functions are called directly and they in turn can call the default
implementations if needed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
It is confusing to have some parts of suspend / resume under conditional
compilation and some parts not. Use conditional compilation everywhere.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Do not use suspend/resume callbacks with runtime pm. It doesn't make sense
and isn't being used, so remove.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
SDHCI provides more flexibility than simply calling sdhci_add_host(). Make
that available by allowing devices to specify their own ->add_host()
function.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Add an interrupt hook and helper functions for enabling, disabling and
delivering interrupts to a CQE.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Get rid of unnecessary 'extern' in header file.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Export sdhci_dumpregs so that it can be called by drivers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Ensure all prints start with the mmc host name, and the text all lines up.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Ensure all debug prints start with the mmc host name.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Tuning execution is already synchronized with respect to other host
operations by upper layers "claiming" the host, which also takes care of
runtime pm. There can be no requests in progress. Retain the spin lock
usage only for ensuring that sending tuning commands is synchronized with
respect to the interrupt handler.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
The spin lock is not necessary in set_ios. Anything that is racing with
changes to the I/O state is already broken. The mmc core already provides
synchronization via "claiming" the host. So remove spin_lock and friends
from sdhci_set_ios and related callbacks.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Drivers can use the host operation directly, so remove this now unused
callback.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Make use of an Intel ACPI _DSM that provides eMMC driver strength.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Make use of an Intel ACPI _DSM that indicates if re-tuning is needed after
D3.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Let devices define their own private data to facilitate device-specific
operations. The size of the private structure is specified in the
sdhci_pci_fixes structure, then sdhci_pci_probe_slot() will allocate extra
space for it, and sdhci_pci_priv() can be used to get a reference to it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Devices might save and restore tuning values so that re-tuning might not be
needed after a pm transition. Let drivers decide by pushing the
mmc_retune_needed() logic down to them.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
The delay loops for reset and clock enable always take at least 1 ms
because they use mdelay(1). However they can take a lot less time e.g. less
than 50us. Use ktime and reduce the delay to 10 microseconds per loop.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
The 2835 has two SD controllers: The Arasan sdhci controller (supported
by the iproc driver) and a custom sdhost controller. This patch adds a
driver for the latter.
The sdhci controller supports both sdcard and sdio. The sdhost
controller supports the sdcard only, but has better performance. Also
note that the rpi3 has sdio wifi, so driving the sdcard with the sdhost
controller allows to use the sdhci controller for wifi support.
The configuration is done by devicetree via pin muxing. Both SD
controller are available on the same pins (2 pin groups = pin 22 to 27 +
pin 48 to 53). So it's possible to use both SD controllers at the same
time with different pin groups.
The code was originally written by Phil Elwell in the downstream
Rasbperry Pi tree. In preparation for the upstream merge it was
cleaned up and the code base was moderized by Eric Anholt, Stefan
Wahren and Gerd Hoffmann.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch fixes the case where meson_mmc_probe function fails before
core_clk is enabled.
Originally, that would result in a try to disable the core clock, and if
it was not already enabled, it would result in a kernel warning.
This issue is similar to the one with div_clk.
Fix it by introducing another error path used only between successfully
enabling the core clock, and successfully enabling the div clock.
That would ensure that core clock is disabled only if it was enabled before.
Signed-off-by: Michał Zegan <webczat@webczatnet.pl>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_pltfm_init() has already set the platform drvdata for us, remove
the unnecessary platform_set_drvdata() call.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_pltfm_init() has already set the platform drvdata for us, remove
the unnecessary platform_set_drvdata() call.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI controller found on NVIDIA Tegra186 SoCs is very similar to
the one on prior generations of Tegra and can be supported by the same
driver.
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The device tree binding for the SDHCI controller found on Tegra SoCs
specifies that a reset control can be provided by the device tree. No
code was ever added to support the module reset, which can cause the
driver to try and access registers from a module that's in reset. On
most Tegra SoC generations doing so would cause a hang.
Note that it's unlikely to see this happen because on most platforms
these resets will have been deasserted by the bootloader. However the
portability can be improved by making sure the driver deasserts the
reset before accessing any registers.
Since resets are synchronous on Tegra SoCs, the platform driver needs
to implement a custom ->remove() callback now to make sure the clock
is disabled after the reset is asserted.
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc host was added in meson_mmc_probe, but never removed in
meson_mmc_remove.
Fix that by removing the host before deallocating other resources.
Signed-off-by: Michał Zegan <webczat@webczatnet.pl>
Tested-by: Michał Zegan <webczat@webczatnet.pl>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After we received the dataend interrupt, R1 response register carries
the value from the automatically generated stop command. Report that
info back to the MMC block layer, so we will be notified in case of e.g.
ECC errors which happened during the last transfer.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Halting the kernel on an unsupported stop command seems overkill, report
the error and say what we already did (due to autocmd12) instead.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Making sure we match the actual register names.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The current code assumes that DMA is finished before SD access end is
flagged. Thus, it schedules the 'dma_complete' tasklet in the SD card
interrupt routine when DATAEND is set. The assumption is not safe,
though. Even by mounting an SD card, it can be seen that sometimes DMA
complete is first, sometimes DATAEND. It seems they are usually close
enough timewise to not cause problems. However, a customer reported that
with CMD53 sometimes things really break apart. As a result, the BSP has
a patch which introduces flags for both events and makes sure both flags
are set before scheduling the tasklet. The customer accepted the patch,
yet it doesn't seem a proper upstream solution to me.
This patch refactors the code to replace the tasklet with already
existing and more lightweight mechanisms. First of all, we set the
callback in a DMA descriptor to automatically get notified when DMA is
done. In the callback, we then use a completion to make sure the SD
access has already ended. Then, we proceed as before.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no check if clk_prepare_enable() succeed in sdhci_pxav2_probe().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Struct mmc_command includes a reference to the related mmc_request.
Therefore we don't have to store mrq separately in struct meson_host.
And we can remove some now unneeded WARN_ON's.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Config values which are not changed during runtime we can set
in the probe function already.
The block size setting is overwritten later in
meson_mmc_start_cmd anyway if needed, so it doesn't harm if we
remove this setting in meson_mmc_set_ios.
In addition write config register only if configuration changed.
Don't change the location of clock initialization as in an
earlier version of the patch, this change causes a hang.
This issue was reported and fix suggested by:
Helmut Klein <hgkr.klein@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CLK core does a deep copy of init.name, therefore it's fully ok to
provide a local variable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The condition should be "if (ret)" as the disable/unprepare is
supposed to be executed if the previous command fails.
In addition adjust the error path in probe to properly deal
with the case that cfg_div_clk can be registered successfully
but enable/prepare fails.
In this case we shouldn't call clk_disable_unprepare.
Reported-by: Michał Zegan <webczat_200@poczta.onet.pl>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Member mux_parent isn't used outside meson_mmc_clk_init. So remove it
and replace it with a local variable in meson_mmc_clk_init.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Because the DT requires a fixed number of mux parent clocks,
variable mux_parent_count can be replaced with constant
MUX_CLK_NUM_PARENTS, so remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Member ocr_mask is never used and member irq we can replace with a
local variable in meson_mmc_probe. So let's remove both members.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The return value of meson_mmc_request_done and meson_mmc_read_resp
isn't used, so make both functions return void.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Core ensures that there are no commands with cmd->data being set and
nothing to transfer. And we don't have to reset bit CMD_CFG_DATA_NUM
because cmd_cfg was zero-initialized and this bit isn't set.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Too much condition iteration makes the code
less readable. Slightly improve it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
No need to declar it there, remove it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Just use the readl_poll_timeout{_atomic} to avold open
coding them.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently for DDR50 card, it need tuning in default. We meet tuning fail
issue for DDR50 card and some data CRC error when DDR50 sd card works.
This is because the default pad I/O drive strength can't make sure DDR50
card work stable. So increase the pad I/O drive strength for DDR50 card,
and use pins_100mhz.
This fixes DDR50 card support for IMX since DDR50 tuning was enabled from
commit 9faac7b95e ("mmc: sdhci: enable tuning for DDR50")
Tested-and-reported-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Cc: stable@vger.kernel.org # v4.4+
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When the kernel is running in secure boot mode, we lock down the kernel to
prevent userspace from modifying the running kernel image. Whilst this
includes prohibiting access to things like /dev/mem, it must also prevent
access by means of configuring driver modules in such a way as to cause a
device to access or modify the kernel image.
To this end, annotate module_param* statements that refer to hardware
configuration and indicate for future reference what type of parameter they
specify. The parameter parser in the core sees this information and can
skip such parameters with an error message if the kernel is locked down.
The module initialisation then runs as normal, but just sees whatever the
default values for those parameters is.
Note that we do still need to do the module initialisation because some
drivers have viable defaults set in case parameters aren't specified and
some drivers support automatic configuration (e.g. PNP or PCI) in addition
to manually coded parameters.
This patch annotates drivers in drivers/mmc/host/.
Suggested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Pierre Ossman <pierre@ossman.eu>
cc: Ulf Hansson <ulf.hansson@linaro.org>
cc: linux-mmc@vger.kernel.org
According to the SDIO standard interrupts are normally signalled in a
very complicated way. They require the card clock to be running and
require the controller to be paying close attention to the signals
coming from the card. This simply can't happen with the clock stopped
or with the controller in a low power mode.
To that end, we'll disable runtime_pm when we detect that an SDIO card
was inserted. This is much like with what we do with the special
"SDMMC_CLKEN_LOW_PWR" bit that dw_mmc supports.
NOTE: we specifically do this Runtime PM disabling at card init time
rather than in the enable_sdio_irq() callback. This is _different_
than how SDHCI does it. Why do we do it differently?
- Unlike SDHCI, dw_mmc uses the standard sdio_irq code in Linux (AKA
dw_mmc doesn't set MMC_CAP2_SDIO_IRQ_NOTHREAD).
- Because we use the standard sdio_irq code:
- We see a constant stream of enable_sdio_irq(0) and
enable_sdio_irq(1) calls. This is because the standard code
disables interrupts while processing and re-enables them after.
- While interrupts are disabled, there's technically a period where
we could get runtime disabled while processing interrupts.
- If we are runtime disabled while processing interrupts, we'll
reset the controller at resume time (see dw_mci_runtime_resume),
which seems like a terrible idea because we could possibly have
another interrupt pending.
To fix the above isues we'd want to put something in the standard
sdio_irq code that makes sure to call pm_runtime get/put when
interrupts are being actively being processed. That's possible to do,
but it seems like a more complicated mechanism when we really just
want the runtime pm disabled always for SDIO cards given that all the
other bits needed to get Runtime PM vs. SDIO just aren't there.
NOTE: at some point in time someone might come up with a fancy way to
do SDIO interrupts and still allow (some) amount of runtime PM.
Technically we could turn off the card clock if we used an alternate
way of signaling SDIO interrupts (and out of band interrupt is one way
to do this). We probably wouldn't actually want to fully runtime
suspend in this case though--at least not with the current
dw_mci_runtime_resume() which basically fully resets the controller at
resume time.
Fixes: e9ed8835e9 ("mmc: dw_mmc: add runtime PM callback")
Cc: <stable@vger.kernel.org>
Reported-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The controller has different timings for MMC_TIMING_UHS_DDR50 and
MMC_TIMING_MMC_DDR52. Configuring the controller with SDHCI_CTRL_UHS_DDR50,
when MMC_TIMING_MMC_DDR52 timings are requested, is not correct and can
lead to unexpected behavior.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Fixes: bb5f8ea4d5 ("mmc: sdhci-of-at91: introduce driver for the Atmel SDMMC")
Cc: <stable@vger.kernel.org> # 4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDIO cards may need clock to send the card interrupt to the host.
On a cherrytrail tablet with a RTL8723BS wifi chip, without this patch
pinging the tablet results in:
PING 192.168.1.14 (192.168.1.14) 56(84) bytes of data.
64 bytes from 192.168.1.14: icmp_seq=1 ttl=64 time=78.6 ms
64 bytes from 192.168.1.14: icmp_seq=2 ttl=64 time=1760 ms
64 bytes from 192.168.1.14: icmp_seq=3 ttl=64 time=753 ms
64 bytes from 192.168.1.14: icmp_seq=4 ttl=64 time=3.88 ms
64 bytes from 192.168.1.14: icmp_seq=5 ttl=64 time=795 ms
64 bytes from 192.168.1.14: icmp_seq=6 ttl=64 time=1841 ms
64 bytes from 192.168.1.14: icmp_seq=7 ttl=64 time=810 ms
64 bytes from 192.168.1.14: icmp_seq=8 ttl=64 time=1860 ms
64 bytes from 192.168.1.14: icmp_seq=9 ttl=64 time=812 ms
64 bytes from 192.168.1.14: icmp_seq=10 ttl=64 time=48.6 ms
Where as with this patch I get:
PING 192.168.1.14 (192.168.1.14) 56(84) bytes of data.
64 bytes from 192.168.1.14: icmp_seq=1 ttl=64 time=3.96 ms
64 bytes from 192.168.1.14: icmp_seq=2 ttl=64 time=1.97 ms
64 bytes from 192.168.1.14: icmp_seq=3 ttl=64 time=17.2 ms
64 bytes from 192.168.1.14: icmp_seq=4 ttl=64 time=2.46 ms
64 bytes from 192.168.1.14: icmp_seq=5 ttl=64 time=2.83 ms
64 bytes from 192.168.1.14: icmp_seq=6 ttl=64 time=1.40 ms
64 bytes from 192.168.1.14: icmp_seq=7 ttl=64 time=2.10 ms
64 bytes from 192.168.1.14: icmp_seq=8 ttl=64 time=1.40 ms
64 bytes from 192.168.1.14: icmp_seq=9 ttl=64 time=2.04 ms
64 bytes from 192.168.1.14: icmp_seq=10 ttl=64 time=1.40 ms
Cc: Dong Aisheng <b29396@freescale.com>
Cc: Ian W MORRISON <ianwmorrison@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Disabling interrupts for even a millisecond can cause problems for some
devices. That can happen when Intel host controllers wait for the present
state to propagate.
The spin lock is not necessary here. Anything that is racing with changes
to the I/O state is already broken. The mmc core already provides
synchronization via "claiming" the host.
Although the spin lock probably should be removed from the code paths that
lead to this point, such a patch would touch too much code to be suitable
for stable trees. Consequently, for this patch, just drop the spin lock
while waiting.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Disabling interrupts for even a millisecond can cause problems for some
devices. That can happen when sdhci changes clock frequency because it
waits for the clock to become stable under a spin lock.
The spin lock is not necessary here. Anything that is racing with changes
to the I/O state is already broken. The mmc core already provides
synchronization via "claiming" the host.
Although the spin lock probably should be removed from the code paths that
lead to this point, such a patch would touch too much code to be suitable
for stable trees. Consequently, for this patch, just drop the spin lock
while waiting.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: 53f3a9e26e ("mmc: USB SD Host Controller (USHC) driver")
Cc: stable <stable@vger.kernel.org> # 2.6.37
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI controller in the SAMA5D2 chip requires a valid voltage set
in the power control register, otherwise commands will fail with a
timeout error.
When using the regulator framework to specify the regulator used by the
mmc device, the voltage is not configured, and it is not possible to use
the connected device.
Implement a custom 'set_power' function for this specific hardware, that
configures the voltage in the register in all cases.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: stable@vger.kernel.org #4.9+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch can fix two issues:
Issue 1:
In previous code, div may be overflow when setting clock frequency
as f_min. We can use DIV_ROUND_UP to fix this boundary related
issue.
Issue 2:
In previous code, we can not set the correct clock frequency when
div equals 0xff.
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_arasan_get_timeout_clock() divides the frequency it has with (1 <<
(13 + divisor)).
However, the divisor is not some Arasan-specific value, but instead is
just the Data Timeout Counter Value from the SDHCI Timeout Control
Register.
Applying it here like this is wrong as the sdhci driver already takes
that value into account when calculating timeouts, and in fact it *sets*
that register value based on how long a timeout is wanted.
Additionally, sdhci core interprets the .get_timeout_clock callback
return value as if it were read from hardware registers, i.e. the unit
should be kHz or MHz depending on SDHCI_TIMEOUT_CLK_UNIT capability bit.
This bit is set at least on the tested Zynq-7000 SoC.
With the tested hardware (SDHCI_TIMEOUT_CLK_UNIT set) this results in
too high a timeout clock rate being reported, causing the core to use
longer-than-needed timeouts. Additionally, on a partitioned MMC
(therefore having erase_group_def bit set) mmc_calc_max_discard()
disables discard support as it looks like controller does not support
the long timeouts needed for that.
Do not apply the extra divisor and return the timeout clock in the
expected unit.
Tested with a Zynq-7000 SoC and a partitioned Toshiba THGBMAG5A1JBAWR
eMMC card.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Fixes: e3ec3a3d11 ("mmc: arasan: Add driver for Arasan SDHCI")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix typos and add the following to the scripts/spelling.txt:
intialization||initialization
The "inintialization" in drivers/acpi/spcr.c is a different pattern but
I fixed it as well in this commit.
Link: http://lkml.kernel.org/r/1481573103-11329-16-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This macro is currently unused, but it may be useful for debug use.
Fix it just in case.
Fixes: ff6af28faf ("mmc: sdhci-cadence: add Cadence SD4HC support")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for HS400 mode.
The driver still misses support for tuning, therefore
highspeed modes like HS400 might not work under all
circumstances yet.
Successfully tested on a Odroid C2 (S905 GXBB).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The remove callback is called only if probe finished successfully.
Therefore these checks are not needed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A bounce buffer of 512K isn't needed as the max request size is
511 * 512 byte.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
So far max_blk_count isn't set what results in a default of value 8
to be used (PAGE_SIZE / block size).
Block length field has 9 bits, so set max_blk_count to 2^9-1 = 511.
In addition set max_req_size because max_blk_count is also limited
by max_req_size / block_size.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Disabling and immediately re-enabling interrupts in meson_mmc_request
doesn't provide a benefit. Instead enable interrupts in probe already.
And disable interrupts in remove, this was missing so far.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove unneeded variable ret and simplify the if block.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The following changes are quite small, therefore I combined them in
one patch.
- ret doesn't need to be initialized with 0
- use standard !clk_rate notation to check for a zero value
- If clk_rate is zero we return here. Therefore all further checks
in this function for clk_rate != 0 are not needed.
- switch from dev_warn to dev_err if the clock can't be set
- If due to clock source and available divider values the requested
frequency isn't matched exactly (always the case if requested
frequency is 52 MHz), then just print the differing values as
debug message and not as warning.
- Also remove ret from the message as it is always 0.
- Set member current_clock to the current requested rate and
mmc->actual_clock to the current actual rate
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
val isn't used in the switch clause and afterwards there's an
identical statement. So remove it.
In case of an unexpected bus width the error message indicates
the intention to set the bus width to 4 and to go on.
So remove the return statement. This return statement also
conflicts with "setting to 4" because nothing would be set
actually before returning. 4bit bus width are chosen as
default as the vendor driver does it too.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The current code dealing with calculating mmc->f_min is a bit complicated.
Additionally, the attempt to set an initial clock rate should explicitly
use a rate between 100KHz to 400 KHz, according the (e)MMC/SD specs, which
it doesn't.
Fix the problem and clean up the code by using clk_round_rate() to pick the
nearest minimum rate to 400KHz (rounded down from 400kHz).
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[Heiner: Changed from 100KHz to 400KHz to get a proper rounded rate]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: a45c6cb816 ("[ARM] 5369/1: omap mmc: Add new omap
hsmmc controller for 2430 and 34xx, v3")
when using really large timeout (up to 4*60*1000 ms for bkops)
there is a possibility of data overflow using
unsigned int so use 64 bit unsigned long long.
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit e2bf08d643 ("omap_hsmmc: set a large data timeout for
commands with busy signal") sets an arbitrary timeout value (100ms) for
commands like CMD6 (MMC SWITCH). However extended CSD register defined
in the eMMC standard has a field for GENERIC_CMD6_TIME which indicates
the default maximum timeout for a SWITCH command.
Use busy_timeout of cmd structure (populated with GENERIC_CMD6_TIME
in the case of SWITCH command) to program the data timeout value in
omap_hsmmc driver.
SWITCH command to turn the cache on took more than 100ms to complete
with MICRON eMMC card present in AM572x IDK REV 1.3A resulting in
timeout and failed enumeration. It is fixed here by programming the
timeout with the value advertised in GENERIC_CMD6_TIME.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When CEB (command end bit error) occurs
reset CMD line to avoid system ending up in
erroneous state.
While command line is reset for CTO and CCRC errors,
it's not done for CEB error. Fix it here.
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When deploying runtime PM, it's quite verbose to print the
log of ios setting. Also it's useless to print it from system
PM as it should be the same with booting time. We also have
sysfs to get all these information from ios attribute, so let's
skip this print from PM context.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit 64b12a68a9
"mmc: core: fix prepared requests while doing bkops"
is fixing a bug in the wrong way. A bug in the MMCI
device driver is fixed by amending the MMC core.
Thinking about it: what the pre- and post-callbacks
are doing is to essentially map and unmap SG lists
for DMA transfers. Why would we not be able to do that
just because a BKOPS command is sent inbetween?
Having to unprepare/prepare the next asynchronous
request for DMA seems wrong.
Looking the backtrace in that commit we can see what
the real problem actually is:
mmci_data_irq() is calling mmci_dma_unmap() twice
which is goung to call arm_dma_unmap_sg() twice
and v7_dma_inv_range() twice for the same sglist
and that will crash.
This happens because a request is prepared, then
a BKOPS is sent. The IRQ completing the BKOPS command
goes through mmci_data_irq() and thinks that a DMA
operation has just been completed because
dma_inprogress() reports true. It then proceeds to
unmap the sglist.
But that was wrong! dma_inprogress() should NOT be
true because no DMA was actually in progress! We had
just prepared the sglist, and the DMA channel
dma_current has been configured, but NOT started!
Because of this, the sglist is already unmapped when
we get our actual data completion IRQ, and we are
unmapping the sglist once more, and we get this crash.
Therefore, we need to revert this solution pushing
the problem to the core and causing problems, and
instead augment the implementation such that
dma_inprogress() only reports true if some DMA has
actually been started.
After this we can keep the request prepared during the
BKOPS and we need not unprepare/reprepare it.
Fixes: 64b12a68a9 ("mmc: core: fix prepared requests while doing bkops")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a bit more debug messages that can be helpful when debugging the clock
setup.
Also fill the actual_clock field in struct mmc_host to report properly the
current frequency in debugfs.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC2 controller on the A64 is kind of a special beast.
While the general controller design is the same than the other MMC
controllers in the SoC, it also has a bunch of features and changes that
prevent it to be driven in the same way.
It has for example a different bus width limit, a different maximum
frequency, and, for some reason, the maximum buffer size of a DMA
descriptor.
Add a new compatible specifically for this controller.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The A64 MMC controllers need DATA0 to be masked while updating the clock,
otherwise any subsequent command will result in a timeout.
It's not really clear at this point what DATA0 is exactly, but this
behaviour is present in Allwinner's tree, and has been suggested by
Allwinner engineers as fixes for the timeout.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The A64 MMC controllers need to set a "new timings" bit when a new rate is
set.
The actual meaning of that bit is not clear yet, but not setting it leads
to some corner-case issues, like the CMD53 failing, which is used to
implement SDIO packet aggregation.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Experience have shown that the using the autocalibration could severely
degrade the performances of the MMC bus.
Allwinner is using in its BSP a delay set to 0 for all the modes but HS400.
Remove the calibration code for now, and add comments to document our
findings.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC core assumes that the code will gate the clock when the bus
frequency is set to 0, which we've been ignoring so far.
Handle that.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SD specification documents that the clock frequency should only be
changed once gated (Section 3.2.3 - SD Clock Frequency Change Sequence).
The current code first modifies the parent clock, gates it and then
modifies the internal divider. This means that since the parent clock rate
might be changed, the bus clock might be changed as well before it is
gated, which breaks the specification.
Move the gating before the parent rate modification.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This removes CDC init sequence comments which are
not useful anyway.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
platform_execute_tuning should not really exist as it does not
do anything useful.
So remove this ops and directly plug sdhci_msm_execute_tuning
with mmc_host_ops.
Also in case of HS400 tuning clear SDHCI_HS400_TUNING flag once
HS400 related mode selection is done.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>