Command queuing has been reported broken on some systems based on Intel
GLK. A separate patch disables command queuing in some cases.
This patch adds a quirk for broken command queuing, which enables users
with problems to disable command queuing using sdhci module parameters for
quirks.
Fixes: 8ee82bda23 ("mmc: sdhci-pci: Add CQHCI support for Intel GLK")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191217095349.14592-2-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Command queuing has been reported broken on some Lenovo systems based on
Intel GLK. This is likely a BIOS issue, so disable command queuing for
Intel GLK if the BIOS vendor string is "LENOVO".
Fixes: 8ee82bda23 ("mmc: sdhci-pci: Add CQHCI support for Intel GLK")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191217095349.14592-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Two previous patches introduced below quirks for P2020 platforms.
- SDHCI_QUIRK_RESET_AFTER_REQUEST
- SDHCI_QUIRK_BROKEN_TIMEOUT_VAL
The patches made a mistake to add them in quirks2 of sdhci_host
structure, while they were defined for quirks.
host->quirks2 |= SDHCI_QUIRK_RESET_AFTER_REQUEST;
host->quirks2 |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL;
This patch is to fix them.
host->quirks |= SDHCI_QUIRK_RESET_AFTER_REQUEST;
host->quirks |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL;
Fixes: 05cb6b2a66 ("mmc: sdhci-of-esdhc: add erratum eSDHC-A001 and A-008358 support")
Fixes: a46e427125 ("mmc: sdhci-of-esdhc: add erratum eSDHC5 support")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191216031842.40068-1-yangbo.lu@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The stm32_sdmmc variant has build-in support for datatimeout for R1B
requests. If a corresponding IRQ is raised, this triggers the DPSM to stay
busy and remains in a non-functional state. Only a reset can bring it back
to a functional state.
Because a reset must be issued from non-atomic context, let's defer this to
be managed from a threaded IRQ handler. Besides the reset, the threaded
handler also calls mmc_request_done(), to finally complete the request.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20191211133934.16932-1-ludovic.Barre@st.com
[Ulf: A few minor updates to the changelog/comments]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are a few places around the code that invert inverted and possibly
inverted CD line. That's really confusing. Squash them all into one place
in mmc_gpiod_request_cd(). MMC_CAP2_CD_ACTIVE_HIGH is used analogously to
WP line: in GPIO mode it is used only at probe time to switch polarity, for
native mode it is left as is.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/db189b715596d63caf8c6a088bddc71dd69a879b.1576031637.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use MMC_CAP2_RO_ACTIVE_HIGH flag as indicator if GPIO line is to be
inverted compared to DT/platform-specified polarity. The flag is not used
after init in GPIO mode anyway. No functional changes intended.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/a60f563f11bbff821da2fa2949ca82922b144860.1576031637.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add possibility to toggle active-low flag of a gpio descriptor. This is
useful for compatibility code, where defaults are inverted vs DT gpio
flags or the active-low flag is taken from elsewhere.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/7ce0338e01ad17fa5a227176813941b41a7c35c1.1576031637.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver forgets to call pci_release_regions() in probe failure
and remove.
Add the missed calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191206075408.18355-1-hslester96@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge an immutable pinctrl branch from Linus Walleij's tree, which enables
pinctrl code consolidations for mmc.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let's drop the boilerplate code for managing the default pinctrl state and
convert into using the new pinctrl_select_default_state().
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191206170821.29711-10-ulf.hansson@linaro.org
Let's move away from using pinctrl_pm_select_default_state() as it's
scheduled for removal and use pinctrl_select_default_state() instead.
Cc: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191206170821.29711-9-ulf.hansson@linaro.org
Let's move away from using pinctrl_pm_select_default_state() as it's
scheduled for removal and use pinctrl_select_default_state() instead.
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191206170821.29711-8-ulf.hansson@linaro.org
Let's drop the boilerplate code for managing the default pinctrl state and
convert into using the new pinctrl_select_default_state().
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191206170821.29711-7-ulf.hansson@linaro.org
Let's drop the boilerplate code for managing the default pinctrl state and
convert into using the new pinctrl_select_default_state().
Additionally, move away from using pinctrl_pm_select_default_state() as
it's scheduled for removal and use pinctrl_select_default_state() instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191206170821.29711-6-ulf.hansson@linaro.org
Let's drop the boilerplate code for managing the default pinctrl state and
convert into using the new pinctrl_select_default_state().
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Lars Persson <lars.persson@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191206170821.29711-5-ulf.hansson@linaro.org
Let's drop the boilerplate code for managing the default pinctrl state and
convert into using the new pinctrl_select_default_state().
Additionally, move away from using pinctrl_pm_select_default_state() as
it's scheduled for removal and use pinctrl_select_default_state() instead.
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191206170821.29711-4-ulf.hansson@linaro.org
Let's drop the boilerplate code for managing the default pinctrl state and
convert into using the new pinctrl_select_default_state().
Cc: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191206170821.29711-3-ulf.hansson@linaro.org
Tuning support in DDR50 speed mode was added in SD Specifications Part1
Physical Layer Specification v3.01. Its not possible to distinguish
between v3.00 and v3.01 from the SCR and that is why since
commit 4324f6de6d ("mmc: core: enable CMD19 tuning for DDR50 mode")
tuning failures are ignored in DDR50 speed mode.
Cards compatible with v3.00 don't respond to CMD19 in DDR50 and this
error gets printed during enumeration and also if retune is triggered at
any time during operation. Update the printk level to pr_debug so that
these errors don't lead to false error reports.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Cc: stable@vger.kernel.org # v4.4+
Link: https://lore.kernel.org/r/20191206114326.15856-1-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Document support for the SDHI controller in the Renesas R-Car M3-W+
(R8A77961) SoC.
Update all references to R-Car M3-W from "r8a7796" to "r8a77960", to
avoid confusion between R-Car M3-W (R8A77960) and M3-W+.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20191205134349.6410-2-geert+renesas@glider.be
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
New datasheets require different and new values for HS400 with 4taps or
8taps.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191203200513.1758-6-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that the quirks structure is accessible, we can remove the TMIO flag
for HS400 using only 4 taps. This is Renesas specific anyhow.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191203200513.1758-5-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We will need that for a later patch.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191203200513.1758-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The warning is not solely used for SDR104 anymore, but for all which
require tuning.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191203200513.1758-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The two devices next to each other are super similar, but still, let's
keep the alphanumeric sorting for easier additions later.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191203200513.1758-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We know now that there won't be Gen3 SoCs with both, SYS-DMAC and
internal DMAC. We removed the blacklisting for SYS-DMAC already, so we
can remove the whitelisting for internal DMAC, too. This makes adding
new SoCs easier. We keep the quirk handling, of course.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191203194859.917-1-wsa@the-dreams.de
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The STOP command is disabled for multiple blocks r/w commands
with auto CMD12, when start to send. However, if there is data
error, software still needs to send CMD12 according to SD spec.
This patch is to allow software CMD12 sending for this case.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20191114111814.35199-1-yangbo.lu@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The code in mmc_spi_initsequence() tries to send a burst with
high chipselect and for this reason hardcodes the device into
SPI_CS_HIGH.
This is not good because the SPI_CS_HIGH flag indicates
logical "asserted" CS not always the physical level. In
some cases the signal is inverted in the GPIO library and
in that case SPI_CS_HIGH is already set, and enforcing
SPI_CS_HIGH again will actually drive it low.
Instead of hard-coding this, toggle the polarity so if the
default is LOW it goes high to assert chipselect but if it
is already high then toggle it low instead.
Cc: Phil Elwell <phil@raspberrypi.org>
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20191204152749.12652-1-linus.walleij@linaro.org
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the SAM9x60 SoC, there are only two clocks instead of three for the
SDHCI device. The base clk is no longer provided, it is generated
internally from the mult clk.
The values of the base clk and mul in the capabilities registers may not
reflect the reality as the mult clk is a programmable clock which can take
several rates. As we can't trust those values, take them from the clock
tree and update the capabilities according to.
As we can have the same pitfall, in some cases, with the SAMA5D2 Soc,
stop relying on capabilities too.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20191128074522.69706-2-ludovic.desroches@microchip.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is a new compatible string for the SAM9X60 sdhci device. It involves
an update of the properties about the clocks stuff.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20191128074522.69706-1-ludovic.desroches@microchip.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tuning support in DDR50 speed mode was added in SD Specifications Part1
Physical Layer Specification v3.01. Its not possible to distinguish
between v3.00 and v3.01 from the SCR and that is why since
commit 4324f6de6d ("mmc: core: enable CMD19 tuning for DDR50 mode")
tuning failures are ignored in DDR50 speed mode.
Cards compatible with v3.00 don't respond to CMD19 in DDR50 and this
error gets printed during enumeration and also if retune is triggered at
any time during operation. Update the printk level to pr_debug so that
these errors don't lead to false error reports.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Cc: stable@vger.kernel.org # v4.4+
Link: https://lore.kernel.org/r/20191206114326.15856-1-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit 5dd1955225.
First, the fix seems to be plain wrong, since the erratum suggests
waiting 5ms before setting setting SYSCTL[RSTD], but this msleep()
happens after the call of sdhci_reset() which is where that bit gets
set (if SDHCI_RESET_DATA is in mask).
Second, walking the whole device tree to figure out if some node has a
"fsl,p2020-esdhc" compatible string is hugely expensive - about 70 to
100 us on our mpc8309 board. Walking the device tree is done under a
raw_spin_lock, so this is obviously really bad on an -rt system, and a
waste of time on all.
In fact, since esdhc_reset() seems to get called around 100 times per
second, that mpc8309 now spends 0.8% of its time determining that
it is not a p2020. Whether those 100 calls/s are normal or due to some
other bug or misconfiguration, regularly hitting a 100 us
non-preemptible window is unacceptable.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191204085447.27491-1-linux@rasmusvillemoes.dk
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
there is a chance that always get response CRC error after HS200 tuning,
the reason is that need set CMD_TA to 2. this modification is only for
MT8173.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
Cc: stable@vger.kernel.org
Fixes: 1ede5cb88a ("mmc: mediatek: Use data tune for CMD line tune")
Link: https://lore.kernel.org/r/20191204071958.18553-1-chaotian.jing@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The DDR_CONFIG register offset got updated after a specific
minor version of sdcc V4. This offset change has not been properly
taken care of while updating register changes for sdcc V5.
Correcting proper offset for this register.
Also updating this register value to reflect the recommended RCLK
delay.
Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/0101016ea738ec72-fa0f852d-20f8-474a-80b2-4b0ef63b132c-000000@us-west-2.amazonses.com
Fixes: f15358885d ("mmc: sdhci-msm: Define new Register address map")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit c894e33ddc.
This commit aims to treat SD High speed and SDR25 as the same while
setting UHS Timings in HOST_CONTROL2 which leads to failures with some
SD cards in AM65x. Revert this commit.
The issue this commit was trying to fix can be implemented in a platform
specific callback instead of common sdhci code.
Cc: <stable@vger.kernel.org>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20191128110422.25917-1-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Update Steve Wise info
- Fix for soft-RoCE crc calculations (will break back compatibility, but
only with the soft-RoCE driver, which has had this bug since it was
introduced and it is an on-the-wire bug, but will make soft-RoCE fully
compatible with real RoCE hardware)
- cma init fixup
- counters oops fix
- fix for mlx4 init/teardown sequence
- fix for mkx5 steering rules
- introduce a cleanup API, which isn't a fix, but we want to use it in
the next fix
- fix for mlx5 memory management that uses API in previous patch
Signed-off-by: Doug Ledford <dledford@redhat.com>
-----BEGIN PGP SIGNATURE-----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=UNwD
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Doug Ledford:
"A small collection of -rc fixes. Mostly. One API addition, but that's
because we wanted to use it in a fix. There's also a bug fix that is
going to render the 5.5 kernel's soft-RoCE driver incompatible with
all soft-RoCE versions prior, but it's required to actually implement
the protocol according to the RoCE spec and required in order for the
soft-RoCE driver to be able to successfully work with actual RoCE
hardware.
Summary:
- Update Steve Wise info
- Fix for soft-RoCE crc calculations (will break back compatibility,
but only with the soft-RoCE driver, which has had this bug since it
was introduced and it is an on-the-wire bug, but will make
soft-RoCE fully compatible with real RoCE hardware)
- cma init fixup
- counters oops fix
- fix for mlx4 init/teardown sequence
- fix for mkx5 steering rules
- introduce a cleanup API, which isn't a fix, but we want to use it
in the next fix
- fix for mlx5 memory management that uses API in previous patch"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
IB/mlx5: Fix device memory flows
IB/core: Introduce rdma_user_mmap_entry_insert_range() API
IB/mlx5: Fix steering rule of drop and count
IB/mlx4: Follow mirror sequence of device add during device removal
RDMA/counter: Prevent auto-binding a QP which are not tracked with res
rxe: correctly calculate iCRC for unaligned payloads
Update mailmap info for Steve Wise
RDMA/cma: add missed unregister_pernet_subsys in init failure
Two minor build fixes:
- Fix builds of the ELF loader when built with 'make -j1' (nommu only)
- Fix CONFIG_SOC_SIFIVE builds when CONFIG_TTY is disabled (found
during randconfig testing)
-----BEGIN PGP SIGNATURE-----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=PVYW
-----END PGP SIGNATURE-----
Merge tag 'riscv/for-v5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Paul Walmsley:
"Two minor build fixes:
- Fix builds of the ELF loader when built with 'make -j1' (nommu
only)
- Fix CONFIG_SOC_SIFIVE builds when CONFIG_TTY is disabled (found
during randconfig testing)"
* tag 'riscv/for-v5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: only select serial sifive if TTY is enabled
riscv: Fix build dependency for loader
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCXfXMXQAKCRCAXGG7T9hj
vvXEAP9Y4gNvKAH+6Puujjtt6QPsdj2StA8JEgo7ZuogCNtvdQD7BAbbfk4cKl7w
7rj8AL8rXXxBJa2rPsQm8B7ZOz6VaQg=
=rgcD
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.5b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Two fixes: one for a resource accounting bug in some configurations
and a fix for another patch which went into rc1"
* tag 'for-linus-5.5b-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/balloon: fix ballooned page accounting without hotplug enabled
xen-blkback: prevent premature module unload
Pull ksys_mount() and ksys_dup() removal from Dominik Brodowski:
"This small series replaces all in-kernel calls to the
userspace-focused ksys_mount() and ksys_dup() with calls to
kernel-centric functions:
For each replacement of ksys_mount() with do_mount(), one needs to
verify that the first and third parameter (char *dev_name, char *type)
are strings allocated in kernelspace and that the fifth parameter
(void *data) is either NULL or refers to a full page (only occurence
in init/do_mounts.c::do_mount_root()). The second and fourth
parameters (char *dir_name, unsigned long flags) are passed by
ksys_mount() to do_mount() unchanged, and therefore do not require
particular care.
Moreover, instead of pretending to be userspace, the opening of
/dev/console as stdin/stdout/stderr can be implemented using in-kernel
functions as well. Thereby, ksys_dup() can be removed for good"
[ This doesn't get rid of the special "kernel init runs with KERNEL_DS"
case, but it at least removes _some_ of the users of "treat kernel
pointers as user pointers for our magical init sequence".
One day we'll hopefully be rid of it all, and can initialize our
init_thread addr_limit to USER_DS. - Linus ]
* 'remove-ksys-mount-dup' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/linux:
fs: remove ksys_dup()
init: unify opening /dev/console as stdin/stdout/stderr
init: use do_mount() instead of ksys_mount()
initrd: use do_mount() instead of ksys_mount()
devtmpfs: use do_mount() instead of ksys_mount()
Hi Linus,
Please, pull the following patches that mark switch cases where we are
expecting to fall through.
- Fix compile error on sh by marking expected switch fall-through
Thanks
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
-----BEGIN PGP SIGNATURE-----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=VG9W
-----END PGP SIGNATURE-----
Merge tag 'Wimplicit-fallthrough-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull fall through fix from Gustavo Silva:
"Fix compile error on sh by marking expected switch fall-through"
* tag 'Wimplicit-fallthrough-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
sh: kgdb: Mark expected switch fall-throughs
24 fixes, all in drivers. The lion's share (16) are qla2xxx and the
rest are iscsi (3), ufs (2), smarpqi, lpfc and libsas.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXfUGbSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishRNxAP4zxu9A
93AijCfJaMhtuzh2bdegf1IC/LXhbu69CQm9bgD+OeQLR9XvopjRBsQC35W1Im5T
73K+w8YTyddZEkOvcio=
=m0Xq
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"24 fixes, all in drivers. The lion's share (16) are qla2xxx and the
rest are iscsi (3), ufs (2), smarpqi, lpfc and libsas"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
scsi: iscsi: Avoid potential deadlock in iscsi_if_rx func
scsi: iscsi: Fix a potential deadlock in the timeout handler
scsi: smartpqi: Update attribute name to `driver_version`
scsi: libsas: stop discovering if oob mode is disconnected
scsi: ufs: Disable autohibern8 feature in Cadence UFS
scsi: iscsi: qla4xxx: fix double free in probe
scsi: ufs: Give an unique ID to each ufs-bsg
scsi: qla2xxx: Add debug dump of LOGO payload and ELS IOCB
scsi: qla2xxx: Ignore PORT UPDATE after N2N PLOGI
scsi: qla2xxx: Don't defer relogin unconditonally
scsi: qla2xxx: Send Notify ACK after N2N PLOGI
scsi: qla2xxx: Configure local loop for N2N target
scsi: qla2xxx: Fix PLOGI payload and ELS IOCB dump length
scsi: qla2xxx: Don't call qlt_async_event twice
scsi: qla2xxx: Allow PLOGI in target mode
scsi: qla2xxx: Change discovery state before PLOGI
scsi: qla2xxx: Drop superfluous INIT_WORK of del_work
scsi: qla2xxx: Initialize free_work before flushing it
scsi: qla2xxx: Use explicit LOGO in target mode
scsi: qla2xxx: Ignore NULL pointer in tcm_qla2xxx_free_mcmd
...
Here are 6 small fixes for some reported char/misc driver issues:
- fix build warnings with new 'awk' with the raid6 code
- 4 interconnect driver bugfixes
- binder fix for reported problem
All of these except the binder fix have been in linux-next with no
reported issues. The binder fix is "new" but Todd says it is good as he
has tested it :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXfT8YQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykUPgCgl9i9JfcQiCkr1oCtKorVhJedtC8AnipcN2up
Q8XJOOLH0pE+J/hTa9Ps
=UfDH
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are six small fixes for some reported char/misc driver issues:
- fix build warnings with new 'awk' with the raid6 code
- four interconnect driver bugfixes
- binder fix for reported problem
All of these except the binder fix have been in linux-next with no
reported issues. The binder fix is "new" but Todd says it is good as
he has tested it :)"
* tag 'char-misc-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
binder: fix incorrect calculation for num_valid
interconnect: qcom: msm8974: Walk the list safely on node removal
interconnect: qcom: qcs404: Walk the list safely on node removal
interconnect: qcom: sdm845: Walk the list safely on node removal
interconnect: qcom: Fix Kconfig indentation
lib: raid6: fix awk build warnings
Here are two small driver core fixes to resolve some reported issues
The first is to handle the much-reported (by the build systems) problem
that superH does not boot anymore.
The second handles an issue in the new platform logic that a number of
people ran into with the automated tests in kbuild
Both of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXfT93A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynmZQCg1UcGXaZKmLfiGCvNMqt2kelW0qwAnjTAtaLv
jj8vb4R+ogOFhEcGE5g/
=BbbT
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are two small driver core fixes to resolve some reported issues
The first is to handle the much-reported (by the build systems)
problem that superH does not boot anymore.
The second handles an issue in the new platform logic that a number of
people ran into with the automated tests in kbuild
Both of these have been in linux-next with no reported issues"
* tag 'driver-core-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
drivers: Fix boot problem on SuperH
of/platform: Unconditionally pause/resume sync state during kernel init
Here are a number of small staging and IIO driver fixes for reported
issues for 5.5-rc2
Nothing major, a bunch of tiny IIO driver issues resolved, and some
staging driver fixes for things that people ran into with 5.5-rc1. Full
details are in the shortlog.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXfT+cg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykdqQCdGFa/Gafh4bWklhqQ9o0BSr7xzgMAn2DADxOp
Ii2JEMss9lSS158I567k
=coTA
-----END PGP SIGNATURE-----
Merge tag 'staging-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO fixes from Greg KH:
"Here are a number of small staging and IIO driver fixes for reported
issues for 5.5-rc2
Nothing major, a bunch of tiny IIO driver issues resolved, and some
staging driver fixes for things that people ran into with 5.5-rc1.
Full details are in the shortlog.
All of these have been in linux-next with no reported issues"
* tag 'staging-5.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (28 commits)
fbtft: Fix the initialization from property algorithm
staging: rtl8712: fix interface sanity check
staging: rtl8188eu: fix interface sanity check
staging: gigaset: add endpoint-type sanity check
staging: gigaset: fix illegal free on probe errors
staging: gigaset: fix general protection fault on probe
staging: vchiq: call unregister_chrdev_region() when driver registration fails
staging: exfat: fix multiple definition error of `rename_file'
staging/wlan-ng: add CRC32 dependency in Kconfig
staging: hp100: Fix build error without ETHERNET
staging: fbtft: Do not hardcode SPI CS polarity inversion
staging: exfat: properly support discard in clr_alloc_bitmap()
staging/octeon: Mark Ethernet driver as BROKEN
iio: adc: max9611: Fix too short conversion time delay
iio: ad7949: fix channels mixups
iio: imu: st_lsm6dsx: do not power-off accel if events are enabled
iio: imu: st_lsm6dsx: track hw FIFO buffering with fifo_mask
iio: imu: st_lsm6dsx: fix decimation factor estimation
iio: imu: inv_mpu6050: fix temperature reporting using bad unit
iio: humidity: hdc100x: fix IIO_HUMIDITYRELATIVE channel reporting
...
Ulf Hansson