- Support for CPU clks on Raspberry Pi devices
- Slow clk support for AT91 SAM9X60 SoCs
* clk-rpi-cpufreq:
clk: raspberrypi: register platform device for raspberrypi-cpufreq
firmware: raspberrypi: register clk device
clk: bcm283x: add driver interfacing with Raspberry Pi's firmware
clk: bcm2835: remove pllb
* clk-tegra:
clk: tegra: Do not enable PLL_RE_VCO on Tegra210
clk: tegra: Warn if an enabled PLL is in IDDQ
clk: tegra: Do not warn unnecessarily
clk: tegra210: fix PLLU and PLLU_OUT1
* clk-simplify-provider.h:
clk: consoldiate the __clk_get_hw() declarations
clk: Unexport __clk_of_table
clk: Remove ifdef for COMMON_CLK in clk-provider.h
* clk-sprd:
clk: sprd: Add check for return value of sprd_clk_regmap_init()
clk: sprd: Check error only for devm_regmap_init_mmio()
clk: sprd: Switch from of_iomap() to devm_ioremap_resource()
* clk-at91:
clk: at91: sckc: use dedicated functions to unregister clock
clk: at91: sckc: improve error path for sama5d4 sck registration
clk: at91: sckc: remove unnecessary line
clk: at91: sckc: improve error path for sam9x5 sck register
clk: at91: sckc: add support to free slow clock osclillator
clk: at91: sckc: add support to free slow rc oscillator
clk: at91: sckc: add support to free slow oscillator
clk: at91: sckc: add support for SAM9X60
dt-bindings: clk: at91: add bindings for SAM9X60's slow clock controller
clk: at91: sckc: add support to specify registers bit offsets
clk: at91: sckc: sama5d4 has no bypass support
Without this we were getting errors like:
In file included from drivers/clk/clkdev.c:22:0:
drivers/clk/clk.h:36:23: error: static declaration of '__clk_get_hw' follows non-static declaration
include/linux/clk-provider.h:808:16: note: previous declaration of '__clk_get_hw' was here
Fixes: 59fcdce425 ("clk: Remove ifdef for COMMON_CLK in clk-provider.h")
fixes: 73e0e496af ("clkdev: Always allocate a struct clk and call __clk_get() w/ CCF")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
With the new clk parenting code, clk_init_data was expanded to include
.parent_data, for clk drivers to specify parents using a combination of
device tree clock-names, pointers to struct clk_hw, device tree clocks,
and/or fallback global clock names.
Add a new macro, CLK_FIXED_FACTOR_FW_NAME, that takes a string to match
a clock-names entry in the device tree to specify the clock parent.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
With the new clk parenting code, clk_init_data was expanded to include
.parent_hws, for clk drivers to directly reference parents by clk_hw.
Add a new macro, CLK_FIXED_FACTOR_HWS, that can take an array of pointers
to struct clk_hw, instead of a string, as its parent. Taking an array
instead of a direct pointer allows the reuse of the array for multiple
clks, rather than having one compound literal with the same contents
allocated for each clk declaration.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
With the new clk parenting code, clk_init_data was expanded to include
.parent_hws, for clk drivers to directly reference parents by clk_hw.
Add a new macro, CLK_FIXED_FACTOR_HW, that can take a struct clk_hw
pointer, instead of a string, as its parent.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
With the new clk parenting code, struct clk_init_data was expanded to
include .parent_data, for clk drivers that have parents referenced using
a combination of device tree clock-names, clock indices, and/or struct
clk_hw pointers.
Add a new macro that can take a list of struct clk_parent_data for
drivers to use.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
With the new clk parenting code, clk_init_data was expanded to include
.parent_data, for clk drivers that have parents referenced using a
combination of device tree clock-names, clock indices, and/or clk_hw
pointers.
Add a CLK_HW_INIT macro for specifying a single parent from the device
tree using .fw_name in struct clk_parent_data.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
With the new clk parenting code, struct clk_init_data was expanded to
include .parent_hws, for clk drivers to directly list parents by
pointing to their respective struct clk_hw's.
Add macros that can take either one single struct clk_hw *, or an array
of them, for drivers to use.
A special CLK_HW_INIT_HWS macro is included, which takes an array of
struct clk_hw *, but sets .num_parents to 1. This variant is to allow
the reuse of the array, instead of having a compound literal allocated
for each clk sharing the same parent.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
This symbol doesn't need to be exported to clk providers anymore.
Originally, it was hidden inside clk.c, but then OMAP needed to get
access to it in commit 819b4861c1 ("CLK: ti: add init support for
clock IP blocks"), but eventually that code also changed in commit
c08ee14cc6 ("clk: ti: change clock init to use generic of_clk_init")
and we were left with this exported. Move this back into clk.c so that
it isn't exposed anymore.
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This ifdef has been there since the beginning of this file, but it
doesn't really seem to serve any purpose besides obfuscating the struct
definitions and #defines here from compilation units that include it.
Let's always expose these function prototypes and struct definitions so
that code can inspect clk providers without needing to have
CONFIG_COMMON_CLK enabled.
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
- Rewrite how clk parents can be specified to be DT/clkdev based instead
of just string based
* clk-parent-rewrite-1:
clk: Cache core in clk_fetch_parent_index() without names
clk: fixed-factor: Initialize clk_init_data on stack
clk: fixed-factor: Let clk framework find parent
clk: Allow parents to be specified via clkspec index
clk: Look for parents with clkdev based clk_lookups
clk: Allow parents to be specified without string names
clk: Add of_clk_hw_register() API for early clk drivers
driver core: Let dev_of_node() accept a NULL dev
clk: Prepare for clk registration API that uses DT nodes
clkdev: Move clk creation outside of 'clocks_mutex'
- Remove clk_readl() and introduce BE versions of basic clk types
* clk-doc:
clk: Drop duplicate clk_register() documentation
clk: Document and simplify clk_core_get_rate_nolock()
clk: Remove 'flags' member of struct clk_fixed_rate
clk: nxp: Drop 'flags' on fixed_rate clk macro
clk: Document __clk_mux_determine_rate()
clk: Document CLK_MUX_READ_ONLY mux flag
clk: Document deprecated things
clk: Collapse gpio clk kerneldoc
* clk-more-critical:
clk: highbank: Convert to CLK_IS_CRITICAL
* clk-meson: (21 commits)
clk: meson: axg-audio: add g12a support
clk: meson: axg-audio: don't register inputs in the onecell data
clk: meson: axg_audio: replace prefix axg by aud
dt-bindings: clk: axg-audio: add g12a support
clk: meson: meson8b: add the video decoder clock trees
clk: meson: meson8b: add the VPU clock trees
clk: meson: meson8b: add support for the GP_PLL clock on Meson8m2
clk: meson: meson8b: use a separate clock table for Meson8m2
dt-bindings: clock: meson8b: export the video decoder clocks
clk: meson-g12a: add video decoder clocks
dt-bindings: clock: meson8b: export the VPU clock
clk: meson-g12a: add PCIE PLL clocks
dt-bindings: clock: g12a-aoclk: expose CLKID_AO_CTS_OSCIN
clk: meson-pll: add reduced specific clk_ops for G12A PCIe PLL
dt-bindings: clock: meson8b: drop the "ABP" clock definition
clk: meson: g12a: add cpu clocks
dt-bindings: clk: g12a-clkc: add VDEC clock IDs
dt-bindings: clock: axg-audio: unexpose controller inputs
dt-bindings: clk: g12a-clkc: add PCIE PLL clock ID
clk: g12a-aoclk: re-export CLKID_AO_SAR_ADC_SEL clock id
...
* clk-basic-be:
clk: core: replace clk_{readl,writel} with {readl,writel}
clk: core: remove powerpc special handling
powerpc/512x: mark clocks as big endian
clk: mux: add explicit big endian support
clk: multiplier: add explicit big endian support
clk: gate: add explicit big endian support
clk: fractional-divider: add explicit big endian support
clk: divider: add explicit big endian support
This flag was historically used to indicate that a clk is a "basic" type
of clk like a mux, divider, gate, etc. This never turned out to be very
useful though because it was hard to cleanly split "basic" clks from
other clks in a system. This one flag was a way for type introspection
and it just didn't scale. If anything, it was used by the TI clk driver
to indicate that a clk_hw wasn't contained in the SoC specific clk
structure. We can get rid of this define now that TI is finding those
clks a different way.
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: <linux-mips@vger.kernel.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: <linux-pwm@vger.kernel.org>
Cc: <linux-amlogic@lists.infradead.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Now that clk_{readl,writel} is just an alias for {readl,writel}, we can
switch all users of clk_* to use the accessors directly and remove the
helpers.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
[sboyd@kernel.org: Also convert renesas file so that this can be
compile independently]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Now that the powerpc clocks are properly marked as big endian, we can
remove the special handling for PowerPC.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add a clock specific flag to switch register accesses to big endian, to
allow runtime configuration of big endian mux clocks.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add a clock specific flag to switch register accesses to big endian, to
allow runtime configuration of big endian multiplier clocks.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add a clock specific flag to switch register accesses to big endian, to
allow runtime configuration of big endian gated clocks.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add a clock specific flag to switch register accesses to big endian, to
allow runtime configuration of big endian fractional divider clocks.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add a clock specific flag to switch register accesses to big endian, to
allow runtime configuration of big endian divider clocks.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Some clk providers are simple DT nodes that only have a 'clocks'
property without having an associated 'clock-names' property. In these
cases, we want to let these clk providers point to their parent clks
without having to dereference the 'clocks' property at probe time to
figure out the parent's globally unique clk name. Let's add an 'index'
property to the parent_data structure so that clk providers can indicate
that their parent is a particular index in the 'clocks' DT property.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The common clk framework is lacking in ability to describe the clk
topology without specifying strings for every possible parent-child
link. There are a few drawbacks to the current approach:
1) String comparisons are used for everything, including describing
topologies that are 'local' to a single clock controller.
2) clk providers (e.g. i2c clk drivers) need to create globally unique
clk names to avoid collisions in the clk namespace, leading to awkward
name generation code in various clk drivers.
3) DT bindings may not fully describe the clk topology and linkages
between clk controllers because drivers can easily rely on globally unique
strings to describe connections between clks.
This leads to confusing DT bindings, complicated clk name generation
code, and inefficient string comparisons during clk registration just so
that the clk framework can detect the topology of the clk tree.
Furthermore, some drivers call clk_get() and then __clk_get_name() to
extract the globally unique clk name just so they can specify the parent
of the clk they're registering. We have of_clk_parent_fill() but that
mostly only works for single clks registered from a DT node, which isn't
the norm. Let's simplify this all by introducing two new ways of
specifying clk parents.
The first method is an array of pointers to clk_hw structures
corresponding to the parents at that index. This works for clks that are
registered when we have access to all the clk_hw pointers for the
parents.
The second method is a mix of clk_hw pointers and strings of local and
global parent clk names. If the .fw_name member of the map is set we'll
look for that clk by performing a DT based lookup of the device the clk
is registered with and the .name specified in the map. If that fails,
we'll fallback to the .name member and perform a global clk name lookup
like we've always done before.
Using either one of these new methods is entirely optional. Existing
drivers will continue to work, and they can migrate to this new approach
as they see fit. Eventually, we'll want to get rid of the 'parent_names'
array in struct clk_init_data and use one of these new methods instead.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Rob Herring <robh@kernel.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
In some circumstances drivers register clks early and don't have access
to a struct device because the device model isn't initialized yet. Add
an API to let drivers register clks associated with a struct device_node
so that these drivers can participate in getting parent clks through DT.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Jeffrey Hugo <jhugo@codeaurora.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Rob Herring <robh@kernel.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
clk_register() isn't the main way to register a clk anymore. Developers
should use clk_hw_register() instead. Furthermore, this whole chunk of
documentation duplicates what's in the C file, so let's just use that.
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Custom approximation of fractional-divider may not need parent clock
rate checking. For example Rockchip SoCs work fine using grand parent
clock rate even if target rate is greater than parent.
This patch checks parent clock rate only if CLK_SET_RATE_PARENT flag
is set.
For detailed example, clock tree of Rockchip I2S audio hardware.
- Clock rate of CPLL is 1.2GHz, GPLL is 491.52MHz.
- i2s1_div is integer divider can divide N (N is 1~128).
Input clock is CPLL or GPLL. Initial divider value is N = 1.
Ex) PLL = CPLL, N = 10, i2s1_div output rate is
CPLL / 10 = 1.2GHz / 10 = 120MHz
- i2s1_frac is fractional divider can divide input to x/y, x and
y are 16bit integer.
CPLL --> | selector | ---> i2s1_div -+--> | selector | --> I2S1 MCLK
GPLL --> | | ,--------------' | |
`--> i2s1_frac ---> | |
Clock mux system try to choose suitable one from i2s1_div and
i2s1_frac for master clock (MCLK) of I2S1.
Bad scenario as follows:
- Try to set MCLK to 8.192MHz (32kHz audio replay)
Candidate setting is
- i2s1_div: GPLL / 60 = 8.192MHz
i2s1_div candidate is exactly same as target clock rate, so mux
choose this clock source. i2s1_div output rate is changed
491.52MHz -> 8.192MHz
- After that try to set to 11.2896MHz (44.1kHz audio replay)
Candidate settings are
- i2s1_div : CPLL / 107 = 11.214945MHz
- i2s1_frac: i2s1_div = 8.192MHz
This is because clk_fd_round_rate() thinks target rate
(11.2896MHz) is higher than parent rate (i2s1_div = 8.192MHz)
and returns parent clock rate.
Above is current upstreamed behavior. Clock mux system choose
i2s1_div, but this clock rate is not acceptable for I2S driver, so
users cannot replay audio.
Expected behavior is:
- Try to set master clock to 11.2896MHz (44.1kHz audio replay)
Candidate settings are
- i2s1_div : CPLL / 107 = 11.214945MHz
- i2s1_frac: i2s1_div * 147/6400 = 11.2896MHz
Change i2s1_div to GPLL / 1 = 491.52MHz at same
time.
If apply this commit, clk_fd_round_rate() calls custom approximate
function of Rockchip even if target rate is higher than parent.
Custom function changes both grand parent (i2s1_div) and parent
(i2s_frac) settings at same time. Clock mux system can choose
i2s1_frac and audio works fine.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
[sboyd@kernel.org: Make function into a macro instead]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We don't want driver authors to use the struct clk based registration
and provider APIs. Instead, they should use the clk_hw based APIs. Add
some notes in the kerneldoc to this effect.
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We have two kernel-docs for gpio clks, but there is only one gpio clk
structure. Collapse the two so we have proper kerneldoc for this basic
clk type.
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Adding CLK_FRAC_DIVIDER_ZERO_BASED flag to indicate the numerator and
denominator value in register are start from 0.
This can be used to support frac dividers like below:
Divider output clock = Divider input clock x [(frac +1) / (div +1)]
where frac/div in register is:
000b - Divide by 1.
001b - Divide by 2.
010b - Divide by 3.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The clock gate restore context function enables or disables
the gate clocks based on the enable_count. This is done in cases
where the clock context is lost and based on the enable_count
the clock either needs to be enabled/disabled.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Deep enough power saving mode can result into losing context of the clock
registers also, and they need to be restored once coming back from the power
saving mode. Hence add functions to save/restore clock context.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add the possibility to apply and query the clock signal duty cycle ratio.
This is useful when the duty cycle of the clock signal depends on some
other parameters controlled by the clock framework.
For example, the duty cycle of a divider may depends on the raw divider
setting (ratio = N / div) , which is controlled by the CCF. In such case,
going through the pwm framework to control the duty cycle ratio of this
clock would be a burden.
A clock provider is not required to implement the operation to set and get
the duty cycle. If it does not implement .get_duty_cycle(), the ratio is
assumed to be 50%.
This change also adds a new flag, CLK_DUTY_CYCLE_PARENT. This flag should
be used to indicate that a clock, such as gates and muxes, may inherit
the duty cycle ratio of its parent clock. If a clock does not provide a
get_duty_cycle() callback and has CLK_DUTY_CYCLE_PARENT, then the call
will be directly forwarded to its parent clock, if any. For
set_duty_cycle(), the clock should also have CLK_SET_RATE_PARENT for the
call to be forwarded
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20180619144141.8506-1-jbrunet@baylibre.com
general cleanups, but nothing too major. The majority of the diff goes to
two SoCs, Actions Semi and Qualcomm. A brand new driver is introduced for
Actions Semi so it takes up some lines to add all the different types, and
the Qualcomm diff is there because we add support for two SoCs and it's quite
a bit of data.
Otherwise the big driver updates are on TI Davinci and Amlogic platforms. And
then the long tail of driver updates for various fixes and stuff follows
after that.
Core:
- debugfs cleanups removing error checking and an unused provider API
- Removal of a clk init typedef that isn't used
- Usage of match_string() to simplify parent string name matching
- OF clk helpers moved to their own file (linux/of_clk.h)
- Make clk warnings more readable across kernel versions
New Drivers:
- Qualcomm SDM845 GCC and Video clk controllers
- Qualcomm MSM8998 GCC
- Actions Semi S900 SoC support
- Nuvoton npcm750 microcontroller clks
- Amlogic axg AO clock controller
Removed Drivers:
- Deprecated Rockchip clk-gate driver
Updates:
- debugfs functions stopped checking return values
- Support for the MSIOF module clocks on Rensas R-Car M3-N
- Support for the new Rensas RZ/G1C and R-Car E3 SoCs
- Qualcomm GDSC, RCG, and PLL updates for clk changes in new SoCs
- Berlin and Amlogic SPDX tagging
- Usage of of_clk_get_parent_count() in more places
- Proper implementation of the CDEV1/2 clocks on Tegra20
- Allwinner H6 PRCM clock support and R40 EMAC support
- Add critical flag to meson8b's fdiv2 as temporary fixup for ethernet
- Round closest support for meson's mpll driver
- Support for meson8b nand clocks and gxbb video decoder clocks
- Mediatek mali clks
- STM32MP1 fixes
- Uniphier LD11/LD20 stream demux system clock
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE9L57QeeUxqYDyoaDrQKIl8bklSUFAlsWxugACgkQrQKIl8bk
lSVs2A/9HOMsWeiYx1MESrXw6N2UknWeqeT/b1v8L/VOiptJg+OTExPbzmSylngv
AXJAfIkCpguSMh9b310pA3DAzk5docmbQ4zL977yY+KXmOcDooCd34aG5a+tB3ie
ugC8T2bQLrJdMp3hsqaKZsYzqe7LoW2NJgoliXDMA/QUBLpvHq+fcu2zOawingTA
GNc3LGqP5Op7p09aPK30gtQNqLK5qGpHASa/AY7Y0PXlUeTZ8rmF06fcEAg5shkC
CT57Zy2rSFB2RorEJarYXDPLRHMw/jxXtpMVXEy7zuz/3ajvvRiZDHv75+NaBru9
hDt1rzslzexEN4fYzj4AtGYRKyBrHbDaxG1qdIWPWVyoE0CEb+dZ1gH7/Ski5r+s
z5D28NogC0T0sey6yWssyG3RLvkPJ5nxUhL++siHm1lbyo16LmhB1+nFvxrlzmBB
0V1xqEa7feYpD+JD66lJFb5ornHLwGtVYBpeiY+hrDR3ddWEe1IxaYGR2p9nHwSS
Us/ZQdHIYBVEqoo3+BWnTn+HSQzmd/sqHqWnLlVWUHoomm5nXx18PeS87vFbcPv9
dMr+FFJ3Elubzcy5UZJPfNw+pb+teE7tYGQkQ3nbLRxT1YZOoIJZJDqNKxM1cgne
6c/VXJMEyBBn/w7Iru/3eWCZVQJGlmYS47DFDzduFvd3LMfmKIM=
=KK/v
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This time we have a good set of changes to the core framework that do
some general cleanups, but nothing too major. The majority of the diff
goes to two SoCs, Actions Semi and Qualcomm. A brand new driver is
introduced for Actions Semi so it takes up some lines to add all the
different types, and the Qualcomm diff is there because we add support
for two SoCs and it's quite a bit of data.
Otherwise the big driver updates are on TI Davinci and Amlogic
platforms. And then the long tail of driver updates for various fixes
and stuff follows after that.
Core:
- debugfs cleanups removing error checking and an unused provider API
- Removal of a clk init typedef that isn't used
- Usage of match_string() to simplify parent string name matching
- OF clk helpers moved to their own file (linux/of_clk.h)
- Make clk warnings more readable across kernel versions
New Drivers:
- Qualcomm SDM845 GCC and Video clk controllers
- Qualcomm MSM8998 GCC
- Actions Semi S900 SoC support
- Nuvoton npcm750 microcontroller clks
- Amlogic axg AO clock controller
Removed Drivers:
- Deprecated Rockchip clk-gate driver
Updates:
- debugfs functions stopped checking return values
- Support for the MSIOF module clocks on Rensas R-Car M3-N
- Support for the new Rensas RZ/G1C and R-Car E3 SoCs
- Qualcomm GDSC, RCG, and PLL updates for clk changes in new SoCs
- Berlin and Amlogic SPDX tagging
- Usage of of_clk_get_parent_count() in more places
- Proper implementation of the CDEV1/2 clocks on Tegra20
- Allwinner H6 PRCM clock support and R40 EMAC support
- Add critical flag to meson8b's fdiv2 as temporary fixup for ethernet
- Round closest support for meson's mpll driver
- Support for meson8b nand clocks and gxbb video decoder clocks
- Mediatek mali clks
- STM32MP1 fixes
- Uniphier LD11/LD20 stream demux system clock"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (134 commits)
clk: qcom: Export clk_fabia_pll_configure()
clk: bcm: Update and add Stingray clock entries
dt-bindings: clk: Update Stingray binding doc
clk-si544: Properly round requested frequency to nearest match
clk: ingenic: jz4770: Add 150us delay after enabling VPU clock
clk: ingenic: jz4770: Enable power of AHB1 bus after ungating VPU clock
clk: ingenic: jz4770: Modify C1CLK clock to disable CPU clock stop on idle
clk: ingenic: jz4770: Change OTG from custom to standard gated clock
clk: ingenic: Support specifying "wait for clock stable" delay
clk: ingenic: Add support for clocks whose gate bit is inverted
clk: use match_string() helper
clk: bcm2835: use match_string() helper
clk: Return void from debug_init op
clk: remove clk_debugfs_add_file()
clk: tegra: no need to check return value of debugfs_create functions
clk: davinci: no need to check return value of debugfs_create functions
clk: bcm2835: no need to check return value of debugfs_create functions
clk: no need to check return value of debugfs_create functions
clk: imx6: add EPIT clock support
clk: mvebu: use correct bit for 98DX3236 NAND
...
* clk-imx7d:
clk: imx7d: reset parent for mipi csi root
clk: imx7d: fix mipi dphy div parent
* clk-hisi-stub:
clk/driver/hisi: Consolidate the Kconfig for the CLOCK_STUB
* clk-mvebu:
clk: mvebu: use correct bit for 98DX3236 NAND
* clk-imx6-epit:
clk: imx6: add EPIT clock support
* clk-debugfs-simple:
clk: Return void from debug_init op
clk: remove clk_debugfs_add_file()
clk: tegra: no need to check return value of debugfs_create functions
clk: davinci: no need to check return value of debugfs_create functions
clk: bcm2835: no need to check return value of debugfs_create functions
clk: no need to check return value of debugfs_create functions
* clk-qcom-rpmh:
dt-bindings: clock: Introduce QCOM RPMh clock bindings
* clk-npcm7xx:
clk: npcm7xx: fix return value check in npcm7xx_clk_init()
clk: npcm7xx: add clock controller
dt-binding: clk: npcm750: Add binding for Nuvoton NPCM7XX Clock
* clk-of-parent-count:
pinctrl: sunxi: Use of_clk_get_parent_count() instead of open coding
soc/tegra: pmc: Use of_clk_get_parent_count() instead of open coding
soc: rockchip: power-domain: Use of_clk_get_parent_count() instead of open coding
ARM: timer-sp: Use of_clk_get_parent_count() instead of open coding
clk: Extract OF clock helpers in <linux/of_clk.h>
* clk-qcom-rcg-fix:
clk: qcom: Base rcg parent rate off plan frequency
We only have two users of the debug_init hook, and we recently stopped
caring about the return value from that op. Finish that off by changing
the clk_op to return void instead of int because it doesn't matter if
debugfs fails or not.
Cc: Eric Anholt <eric@anholt.net>
Cc: David Lechner <david@lechnology.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
No one was using this api call, so remove it. If it is ever needed in
the future, a "raw" debugfs call can be used.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The use of of_clk_get_parent_{count,name}() and of_clk_init() is not
limited to clock providers.
Hence move these helpers into their own header file, so callers that are
not clock providers no longer have to include <linux/clk-provider.h>.
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Since commit c08ee14cc6 ("clk: ti: change clock init to use
generic of_clk_init"), there is only a single (private) user left of the
(public) clk_init_cb typedef.
Hence expand its single user in the core clock code, and remove the
typedef.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1523365565-17124-1-git-send-email-geert+renesas@glider.be
CLK_MUX_ROUND_CLOSEST is part of the clk_mux documentation but clk_mux
directly calls __clk_mux_determine_rate(), which overrides the flag.
As result, if clk_mux is instantiated with CLK_MUX_ROUND_CLOSEST, the
flag will be ignored and the clock rounded down.
To solve this, this patch expose clk_mux_determine_rate_flags() in the
clk-provider API and uses it in the determine_rate() callback of clk_mux.
Fixes: 15a02c1f6d ("clk: Add __clk_mux_determine_rate_closest")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When a divider clock has CLK_DIVIDER_READ_ONLY set, it means that the
register shall be left un-touched, but it does not mean the clock
should stop rate propagation if CLK_SET_RATE_PARENT is set
This is properly handled in qcom clk-regmap-divider but it was not in
the generic divider
To fix this situation, introduce a new helper function
divider_ro_round_rate, on the same model as divider_round_rate.
Fixes: e6d5e7d90b ("clk-divider: Fix READ_ONLY when divider > 1")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-By: David Lechner <david@lechnology.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The mux documentation mentions the non-existing parameter width instead
of mask, so just sed this.
The table field is missing in the documentation of clk_mux.
Add a small blurb explaining what it is
Fixes: 9d9f78ed9a ("clk: basic clock hardware types")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add helper functions for the translation between parent index and
register value in the generic multiplexer function. The purpose of
this change is avoid duplicating the code in other clock providers,
using the same generic logic.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Export clk_div_mask() in clk-provider header so every clock providers
derived from the generic clock divider may share the definition instead
of redefining it.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk-remove-asm-clkdev:
clk: Move __clk_{get,put}() into private clk.h API
clk: sunxi: Use CLK_IS_CRITICAL flag for critical clks
arch: Remove clkdev.h asm-generic from Kbuild
clk: Prepare to remove asm-generic/clkdev.h
blackfin: Use generic clkdev.h header
* clk-debugfs-fixes:
clk: Simplify debugfs registration
clk: Fix debugfs_create_*() usage
clk: Show symbolic clock flags in debugfs
clk: Improve flags doc for of_clk_detect_critical()
* clk-renesas:
clk: renesas: r8a7796: Add FDP clock
clk: renesas: cpg-mssr: Keep wakeup sources active during system suspend
clk: renesas: mstp: Keep wakeup sources active during system suspend
clk: renesas: r8a77970: Add LVDS clock
* clk-meson:
clk: meson-axg: fix potential NULL dereference in axg_clkc_probe()
clk: meson-axg: make local symbol axg_gp0_params_table static
clk: meson-axg: fix return value check in axg_clkc_probe()
clk: meson: mpll: use 64-bit maths in params_from_rate
clk: meson-axg: add clock controller drivers
clk: meson-axg: add clocks dt-bindings required header
dt-bindings: clock: add compatible variant for the Meson-AXG
clk: meson: make the spinlock naming more specific
clk: meson: gxbb: remove IGNORE_UNUSED from mmc clocks
clk: meson: gxbb: fix wrong clock for SARADC/SANA
Stephen Boyd