First set of patches for v5.6. The biggest thing here is of course the
new driver ath11k but also new features for other drivers as well a
myriad of bug fixes.
Major changes:
ath11k
* a new driver for Qualcomm Wi-Fi 6 (IEEE 802.11ax) devices
ath10k
* significant improvements on receive throughput and firmware download
with SDIO bus
* report signal strength for each chain also on SDIO
* set max mtu to 1500 on SDIO devices
brcmfmac
* add support for BCM4359 SDIO chipset
wil6210
* support set_multicast_to_unicast cfg80211 operation
* support set_cqm_rssi_config cfg80211 operation
wcn36xx
* disable HW_CONNECTION_MONITOR as firmware is buggy
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJd/OTiAAoJEG4XJFUm622bN3MH+gM/uwAyMUOLK/x+9dyL+nnO
y8/QbtkM9eyMaMJ+8BoA4XVs8Md5K0YPEUoV22VoTKXgRLX5G2dwoFC5TbuuIxGF
6ptojEoc6XsYYOySHGlgEwPhR8UYf3YfvpgerqbENeiCA82ZHrY9MSUEReEGLr6U
OSb+qcP1KtwpIvo8u4hhomJQO4vO1iY+Z1+6tUzDzpzk3t/rsX2dg9083Cw46JgT
deruvZziwFLsws4EVoBUxa9OPg4Jz/zelRlgHpAXi4VWr7GM9p2cqTia0OwE/coX
VCberklKTJLQfpp5L3uZ9QX4MwSwhTJC/rPiwm9a+4TezT7yVAexF2Q+L/nKKRQ=
=nRvm
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2019-12-20' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.6
First set of patches for v5.6. The biggest thing here is of course the
new driver ath11k but also new features for other drivers as well a
myriad of bug fixes.
Major changes:
ath11k
* a new driver for Qualcomm Wi-Fi 6 (IEEE 802.11ax) devices
ath10k
* significant improvements on receive throughput and firmware download
with SDIO bus
* report signal strength for each chain also on SDIO
* set max mtu to 1500 on SDIO devices
brcmfmac
* add support for BCM4359 SDIO chipset
wil6210
* support set_multicast_to_unicast cfg80211 operation
* support set_cqm_rssi_config cfg80211 operation
wcn36xx
* disable HW_CONNECTION_MONITOR as firmware is buggy
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan says:
====================
net: hns3: misc updates for -net-next
This series includes some misc updates for the HNS3 ethernet driver.
[patch 1] adds FE bit check before calling hns3_add_frag().
[patch 2] removes an unnecessary lock.
[patch 3] adds a little optimization for CMDQ uninitialization.
[patch 4] refactors the dump of FD tcams.
[patch 5] implements ndo_features_check ops.
[patch 6] adds some VF VLAN information for command "ip link show".
[patch 7] adds a debug print.
[patch 8] modifies the timing of print misc interrupt status when
handling hardware error event.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Printing misc interrupt status of hardware error event in the
IRQ handler is unnecessary, since hclge_handle_hw_msix_error()
will print out the detail information for this hardware error
when handling success. So, this patch removes the print in
IRQ handler, and prints it when hclge_handle_hw_msix_error()
fails.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the mapping can be overwritten, when fail to get
the chain between vector and ring, we should go on to
deal with the remaining options. For debugging, this
patch adds log info for this failure.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds some VF VLAN information for command "ip link show".
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function netif_skb_features() will disable the TSO feature
by using dflt_features_check() if the driver does not implement
ndo_features_check ops, which may cause performance degradation
problem when hns3 hardware can do multiple tagged TSO.
Also, the HNS3 hardware only supports checksum on the SKB with
a max header len of 480 bytes, so remove the checksum and TSO
related features when the header len is over 480 bytes.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the dump FD tcam mode in debugfs is to query all FD tcams,
including empty rules, which is unnecessary. This patch modify to
find the position of useful rules before dump FD tcam, so that it does
not need to query empty rules.
This patch also modifies some help information in debugfs.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When uninitializing CMDQ, HCLGE_STATE_CMD_DISABLE will
be set up firstly, then the driver does not send command
anymore. So, hclge_free_cmd_desc can be called without
holding ring->lock. hclge_destroy_cmd_queue() and
hclge_destroy_queue() are unnecessary now, so removes them,
the VF driver has implemented currently.
BTW, the VF driver should set up HCLGEVF_STATE_CMD_DISABLE
as well in the hclgevf_cmd_uninit(), just likes what the PF
driver does.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mutex vport_cfg_mutex has been used to protect uc_mac_list,
mc_mac_list and vlan_list from being modified by unloading
or reset task at the same time. But now unloading will
set up HCLGE_STATE_REMOVING flag and call cancel_work_sync to
break down this race condition, so this mutex is unnecessary.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A BD with FE bit means that it is the last BD of a packet,
currently the FE bit is checked before calling hns3_add_frag(),
which is unnecessary because the FE bit may have been checked
in some case.
This patch checks the FE bit before calling hns3_add_frag()
after processing the first BD of a SKB and adjust the location
of memcpy() to reduce duplication.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To enable iproute2/tipc to generate backwards compatible
printouts and validate command parameters for nodes using a
<z.c.n> node address, it needs to be able to read the legacy
address flag from the kernel. The legacy address flag records
the way in which the node identity was originally specified.
The legacy address flag is requested by the netlink message
TIPC_NL_ADDR_LEGACY_GET. If the flag is set the attribute
TIPC_NLA_NET_ADDR_LEGACY is set in the return message.
Signed-off-by: John Rutherford <john.rutherford@dektech.com.au>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefano Garzarella says:
====================
VSOCK: add vsock_test test suite
The vsock_diag.ko module already has a test suite but the core AF_VSOCK
functionality has no tests. This patch series adds several test cases that
exercise AF_VSOCK SOCK_STREAM socket semantics (send/recv, connect/accept,
half-closed connections, simultaneous connections).
The v1 of this series was originally sent by Stefan.
v3:
- Patch 6:
* check the byte received in the recv_byte()
* use send(2)/recv(2) instead of write(2)/read(2) to test also flags
(e.g. MSG_PEEK)
- Patch 8:
* removed unnecessary control_expectln("CLOSED") [Stefan].
- removed patches 9,10,11 added in the v2
- new Patch 9 add parameters to list and skip tests (e.g. useful for vmci
that doesn't support half-closed socket in the host)
- new Patch 10 prints a list of options in the help
- new Patch 11 tests MSG_PEEK flags of recv(2)
v2: https://patchwork.ozlabs.org/cover/1140538/
v1: https://patchwork.ozlabs.org/cover/847998/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Test if the MSG_PEEK flags of recv(2) works as expected.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we now have several options, in the help we print the list
of all supported options and a brief description of them.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some tests can fail with transports that have a slightly
different behavior, so let's add the possibility to specify
which tests to skip.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before check if a send returns -EPIPE, we need to make sure the
connection is closed.
To do that, we use epoll API to wait EPOLLRDHUP or EPOLLHUP events
on the socket.
Reported-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vsock_test.c program runs a test suite of AF_VSOCK test cases.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test cases will want to transfer data. This patch adds utility
functions to do this.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
See code comment for details.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many test cases will need to connect to the server or accept incoming
connections. This patch extracts these operations into utility
functions that can be reused.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move useful functions into a separate file in preparation for more
vsock test programs.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vsock_diag_test program directly included ../../../include/uapi/
headers from the source tree. Tests are supposed to use the
usr/include/linux/ headers that have been prepared with make
headers_install instead.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Oleksij Rempel says:
====================
add dsa switch support for ar9331
changes v6:
- remove ag71xx changes from this patch set. It needs more work.
- ar9331: fix register definition and add ASCII art switch documentation.
changes v6:
- rebase against net-next
changes v5:
- remote support for port5. The effort of using this port is
questionable. Currently, it is better to not use it at all, then
adding buggy support.
- remove port enable call back. There is nothing what we actually need
to enable.
- rebase it against v5.5-rc1
changes v4:
- ag71xx: ag71xx_mac_validate fix always false comparison (&& -> ||)
- tag_ar9331: use skb_pull_rcsum() instead of skb_pull().
- tag_ar9331: drop skb_set_mac_header()
changes v3:
- ag71xx: ag71xx_mac_config: ignore MLO_AN_INBAND mode. It is not
supported by HW and SW.
- ag71xx: ag71xx_mac_validate: return all supported bits on
PHY_INTERFACE_MODE_NA
changes v2:
- move Atheros AR9331 TAG format to separate patch
- use netdev_warn_once in the tag driver to reduce potential message spam
- typo fixes
- reorder tag driver alphabetically
- configure switch to maximal frame size
- use mdiobus_read/write
- fail if mdio sub node is not found
- add comment for post reset state
- remove deprecated comment about device id
- remove phy-handle option for node with fixed-link
- ag71xx: set 1G support only for GMII mode
This patch series provides dsa switch support for Atheros ar9331 WiSoC.
As side effect ag71xx needed to be ported to phylink to make the switch
driver (as well phylink based) work properly.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide basic support for Atheros AR9331 built-in switch. So far it
works as port multiplexer without any hardware offloading support.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for tag format used in Atheros AR9331 built-in switch.
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add switch node supported by dsa ar9331 driver.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Atheros AR9331 has built-in 5 port switch. The switch can be configured
to use all 5 or 4 ports. One of built-in PHYs can be used by first built-in
ethernet controller or to be used directly by the switch over second ethernet
controller.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns
../drivers/nfc/pn544/pn544.c:696:4: warning: misleading indentation;
statement is not part of the previous 'if' [-Wmisleading-indentation]
return nfc_hci_send_cmd(hdev, NFC_HCI_RF_READER_A_GATE,
^
../drivers/nfc/pn544/pn544.c:692:3: note: previous statement is here
if (target->nfcid1_len != 4 && target->nfcid1_len != 7 &&
^
1 warning generated.
This warning occurs because there is a space after the tab on this line.
Remove it so that the indentation is consistent with the Linux kernel
coding style and clang no longer warns.
Fixes: da052850b9 ("NFC: Add pn544 presence check for different targets")
Link: https://github.com/ClangBuiltLinux/linux/issues/814
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Doug Berger says:
====================
net: bcmgenet: Turn on offloads by default
This commit stack is based on Florian's commit 4e8aedfe78c7 ("net:
systemport: Turn on offloads by default") and enables the offloads for
the bcmgenet driver by default.
The first commit adds support for the HIGHDMA feature to the driver.
The second converts the Tx checksum implementation to use the generic
hardware logic rather than the deprecated IP centric methods.
The third modifies the Rx checksum implementation to use the hardware
offload to compute the complete checksum rather than filtering out bad
packets detected by the hardware's IP centric implementation. This may
increase processing load by passing bad packets to the network stack,
but it provides for more flexible handling of packets by the network
stack without requiring software computation of the checksum.
The remaining commits mirror the extensions Florian made to the sysport
driver to retain symmetry with that driver and to make the benefits of
the hardware offloads more ubiquitous.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When inserting the TSB, keep track of how many times we had to do
it and if there was a failure in doing so, this helps profile the
driver for possibly incorrect headroom settings.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During bcmgenet_put_tx_csum() make sure we differentiate a SKB
headroom re-allocation failure from the normal swap and replace
path.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can turn on the RX/TX checksum offloads and the scatter/gather
features by default and make sure that those are properly reflected
back to e.g: stacked devices such as VLAN.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During driver resume and open, the HW may have lost its context/state,
utilize bcmgenet_set_features() to make sure we do restore the correct
set of features that were previously configured.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally enabling TX and RX checksum
offloads, refactor bcmgenet_set_features() a bit such that
__netdev_update_features() during register_netdev() can make sure
that features are correctly programmed during network device
registration.
Since we can now be called during register_netdev() with clocks
gated, we need to temporarily turn them on/off in order to have a
successful register programming.
We also move the CRC forward setting read into
bcmgenet_set_features() since priv->crc_fwd_en matters while
turning on RX checksum offload, that way we are guaranteed they
are in sync in case we ever add support for NETIF_F_RXFCS at some
point in the future.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit updates the Rx checksum offload behavior of the driver
to use the more generic CHECKSUM_COMPLETE method that supports all
protocols over the CHECKSUM_UNNECESSARY method that only applies
to some protocols known by the hardware.
This behavior is perceived to be superior.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GENET hardware should be capable of generating IP checksums
using the NETIF_F_HW_CSUM feature, so switch to using that feature
instead of the depricated NETIF_F_IP_CSUM and NETIF_F_IPV6_CSUM.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit configures the DMA masks for the GENET driver and
sets the NETIF_F_HIGHDMA flag to report support of the feature.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SYSTEMPORT is capabable of doing up to 40-bit of physical addresses, set
an appropriate DMA mask to permit that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
nfp: tls: implement the stream sync RX resync
This small series adds support for using the device
in stream scan RX resync mode which improves the RX
resync success rate. Without stream scan it's pretty
much impossible to successfully resync a continuous
stream.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The simple RX resync strategy controlled by the kernel does not
guarantee as good results as if the device helps by detecting
the potential record boundaries and keeping track of them.
We've called this strategy stream scan in the tls-offload doc.
Implement this strategy for the NFP. The device sends a request
for record boundary confirmation, which is then recorded in
per-TLS socket state and responded to once record is reached.
Because the device keeps track of records passing after the
request was sent the response is not as latency sensitive as
when kernel just tries to tell the device the information
about the next record.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is currently no way for driver to reliably check that
the socket it has looked up is in fact RX offloaded. Add
a helper. This allows drivers to catch misbehaving firmware.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make nfp_net_parse_meta() take a packet pointer and return
a drop/no drop decision. Right now it returns the end of
metadata and caller compares it to the packet pointer.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Hurley says:
====================
Add ipv6 tunnel support to NFP
The following patches add support for IPv6 tunnel offload to the NFP
driver.
Patches 1-2 do some code tidy up and prepare existing code for reuse in
IPv6 tunnels.
Patches 3-4 handle IPv6 tunnel decap (match) rules.
Patches 5-8 handle encap (action) rules.
Patch 9 adds IPv6 support to the merge and pre-tunnel rule functions.
v1->v2:
- fix compiler warning when building without CONFIG_IPV6 set -
Jakub Kicinski (patch 7)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Both pre-tunnel match rules and flow merge functions parse compiled
match/action fields for validation.
Update these validation functions to include IPv6 match and action fields.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW sends an update of IPv6 tunnels that are active in a given period. Use
this information to update the kernel table so that neighbour entries do
not time out when active on the NIC.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A notifier is used to track route changes in the kernel. If a change is
made to a route that is offloaded to fw then an update is sent to the NIC.
The driver tracks all routes that are offloaded to determine if a kernel
change is of interest.
Extend the notifier to track IPv6 route changes and create a new list that
stores offloaded IPv6 routes. Modify the IPv4 route helper functions to
accept varying address lengths. This way, the same core functions can be
used to handle IPv4 and IPv6.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When fw does not know the next hop for an IPv6 tunnel, it sends a request
to the driver.
Handle this request by doing a route lookup on the IPv6 address and
offloading the next hop to the fw neighbour table.
Similar functions already exist to handle IPv4 no neighbour requests. To
avoid confusion, append these functions with the _ipv4 tag. There is no
change in functionality with this.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IPv4 set tunnel action allows the setting of tunnel metadata such as
the TTL and ToS values. The pre-tunnel action includes the destination IP
address and is used to calculate the next hop from from the neighbour
table.
Much of the IPv4 tunnel actions can be reused for IPv6 tunnels. Change the
names of associated functions and structs to remove the IPv4 identifier
and make minor modifcations to support IPv6 tunnel actions.
Ensure the pre-tunnel action contains the IPv6 address along with an
identifying flag when an IPv6 tunnel action is required.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fw requires a list of IPv6 addresses that are used as tunnel endpoints to
enable correct decap of tunneled packets.
Store a list of IPv6 endpoints used in rules with a ref counter to track
how many times it is in use. Offload the entire list any time a new IPv6
address is added or when an address is removed (ref count is 0).
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller