Pull x86 mm changes from Ingo Molnar:
"PCID support, 5-level paging support, Secure Memory Encryption support
The main changes in this cycle are support for three new, complex
hardware features of x86 CPUs:
- Add 5-level paging support, which is a new hardware feature on
upcoming Intel CPUs allowing up to 128 PB of virtual address space
and 4 PB of physical RAM space - a 512-fold increase over the old
limits. (Supercomputers of the future forecasting hurricanes on an
ever warming planet can certainly make good use of more RAM.)
Many of the necessary changes went upstream in previous cycles,
v4.14 is the first kernel that can enable 5-level paging.
This feature is activated via CONFIG_X86_5LEVEL=y - disabled by
default.
(By Kirill A. Shutemov)
- Add 'encrypted memory' support, which is a new hardware feature on
upcoming AMD CPUs ('Secure Memory Encryption', SME) allowing system
RAM to be encrypted and decrypted (mostly) transparently by the
CPU, with a little help from the kernel to transition to/from
encrypted RAM. Such RAM should be more secure against various
attacks like RAM access via the memory bus and should make the
radio signature of memory bus traffic harder to intercept (and
decrypt) as well.
This feature is activated via CONFIG_AMD_MEM_ENCRYPT=y - disabled
by default.
(By Tom Lendacky)
- Enable PCID optimized TLB flushing on newer Intel CPUs: PCID is a
hardware feature that attaches an address space tag to TLB entries
and thus allows to skip TLB flushing in many cases, even if we
switch mm's.
(By Andy Lutomirski)
All three of these features were in the works for a long time, and
it's coincidence of the three independent development paths that they
are all enabled in v4.14 at once"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (65 commits)
x86/mm: Enable RCU based page table freeing (CONFIG_HAVE_RCU_TABLE_FREE=y)
x86/mm: Use pr_cont() in dump_pagetable()
x86/mm: Fix SME encryption stack ptr handling
kvm/x86: Avoid clearing the C-bit in rsvd_bits()
x86/CPU: Align CR3 defines
x86/mm, mm/hwpoison: Clear PRESENT bit for kernel 1:1 mappings of poison pages
acpi, x86/mm: Remove encryption mask from ACPI page protection type
x86/mm, kexec: Fix memory corruption with SME on successive kexecs
x86/mm/pkeys: Fix typo in Documentation/x86/protection-keys.txt
x86/mm/dump_pagetables: Speed up page tables dump for CONFIG_KASAN=y
x86/mm: Implement PCID based optimization: try to preserve old TLB entries using PCID
x86: Enable 5-level paging support via CONFIG_X86_5LEVEL=y
x86/mm: Allow userspace have mappings above 47-bit
x86/mm: Prepare to expose larger address space to userspace
x86/mpx: Do not allow MPX if we have mappings above 47-bit
x86/mm: Rename tasksize_32bit/64bit to task_size_32bit/64bit()
x86/xen: Redefine XEN_ELFNOTE_INIT_P2M using PUD_SIZE * PTRS_PER_PUD
x86/mm/dump_pagetables: Fix printout of p4d level
x86/mm/dump_pagetables: Generalize address normalization
x86/boot: Fix memremap() related build failure
...
Compared to the old xrx200_phy_fw driver the new version has multiple
enhancements. The name of the firmware files does not have to be added
to all .dts files anymore - one now configures the GPHY mode (FE or GE)
instead. Each GPHY can now also boot separate firmware (thus mixing of
GE and FE GPHYs is now possible).
The new implementation is based on the RCU syscon-mfd and uses the
reeset_controller framework instead of raw RCU register reads/writes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: john@phrozen.org
Cc: p.zabel@pengutronix.de
Cc: kishon@ti.com
Cc: mark.rutland@arm.com
Cc: linux-mips@linux-mips.org
Cc: linux-mtd@lists.infradead.org
Cc: linux-watchdog@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-spi@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/17128/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The reset controllers (on xRX200 and newer SoCs have two of them) are
provided by the RCU module. This was initially implemented as a simple
reset controller. However, the RCU module provides more functionality
(ethernet GPHYs, USB PHY, etc.), which makes it a MFD device.
The old reset controller driver implementation from
arch/mips/lantiq/xway/reset.c did not honor this fact.
For some devices the request and the status bits are different.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Cc: john@phrozen.org
Cc: kishon@ti.com
Cc: mark.rutland@arm.com
Cc: linux-mips@linux-mips.org
Cc: linux-mtd@lists.infradead.org
Cc: linux-watchdog@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-spi@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/17125/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Provide a simple driver for PWM controllable vibrators.
It will be used by Motorola Droid 4.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull locking updates from Ingo Molnar:
- Add 'cross-release' support to lockdep, which allows APIs like
completions, where it's not the 'owner' who releases the lock, to be
tracked. It's all activated automatically under
CONFIG_PROVE_LOCKING=y.
- Clean up (restructure) the x86 atomics op implementation to be more
readable, in preparation of KASAN annotations. (Dmitry Vyukov)
- Fix static keys (Paolo Bonzini)
- Add killable versions of down_read() et al (Kirill Tkhai)
- Rework and fix jump_label locking (Marc Zyngier, Paolo Bonzini)
- Rework (and fix) tlb_flush_pending() barriers (Peter Zijlstra)
- Remove smp_mb__before_spinlock() and convert its usages, introduce
smp_mb__after_spinlock() (Peter Zijlstra)
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (56 commits)
locking/lockdep/selftests: Fix mixed read-write ABBA tests
sched/completion: Avoid unnecessary stack allocation for COMPLETION_INITIALIZER_ONSTACK()
acpi/nfit: Fix COMPLETION_INITIALIZER_ONSTACK() abuse
locking/pvqspinlock: Relax cmpxchg's to improve performance on some architectures
smp: Avoid using two cache lines for struct call_single_data
locking/lockdep: Untangle xhlock history save/restore from task independence
locking/refcounts, x86/asm: Disable CONFIG_ARCH_HAS_REFCOUNT for the time being
futex: Remove duplicated code and fix undefined behaviour
Documentation/locking/atomic: Finish the document...
locking/lockdep: Fix workqueue crossrelease annotation
workqueue/lockdep: 'Fix' flush_work() annotation
locking/lockdep/selftests: Add mixed read-write ABBA tests
mm, locking/barriers: Clarify tlb_flush_pending() barriers
locking/lockdep: Make CONFIG_LOCKDEP_CROSSRELEASE and CONFIG_LOCKDEP_COMPLETIONS truly non-interactive
locking/lockdep: Explicitly initialize wq_barrier::done::map
locking/lockdep: Rename CONFIG_LOCKDEP_COMPLETE to CONFIG_LOCKDEP_COMPLETIONS
locking/lockdep: Reword title of LOCKDEP_CROSSRELEASE config
locking/lockdep: Make CONFIG_LOCKDEP_CROSSRELEASE part of CONFIG_PROVE_LOCKING
locking/refcounts, x86/asm: Implement fast refcount overflow protection
locking/lockdep: Fix the rollback and overwrite detection logic in crossrelease
...
Pull x86 microcode loading updates from Ingo Molnar:
"Update documentation, improve robustness and fix a memory leak"
* 'x86-microcode-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/microcode/intel: Improve microcode patches saving flow
x86/microcode: Document the three loading methods
x86/microcode/AMD: Free unneeded patch before exit from update_cache()
Pull x86 asm updates from Ingo Molnar:
- Introduce the ORC unwinder, which can be enabled via
CONFIG_ORC_UNWINDER=y.
The ORC unwinder is a lightweight, Linux kernel specific debuginfo
implementation, which aims to be DWARF done right for unwinding.
Objtool is used to generate the ORC unwinder tables during build, so
the data format is flexible and kernel internal: there's no
dependency on debuginfo created by an external toolchain.
The ORC unwinder is almost two orders of magnitude faster than the
(out of tree) DWARF unwinder - which is important for perf call graph
profiling. It is also significantly simpler and is coded defensively:
there has not been a single ORC related kernel crash so far, even
with early versions. (knock on wood!)
But the main advantage is that enabling the ORC unwinder allows
CONFIG_FRAME_POINTERS to be turned off - which speeds up the kernel
measurably:
With frame pointers disabled, GCC does not have to add frame pointer
instrumentation code to every function in the kernel. The kernel's
.text size decreases by about 3.2%, resulting in better cache
utilization and fewer instructions executed, resulting in a broad
kernel-wide speedup. Average speedup of system calls should be
roughly in the 1-3% range - measurements by Mel Gorman [1] have shown
a speedup of 5-10% for some function execution intense workloads.
The main cost of the unwinder is that the unwinder data has to be
stored in RAM: the memory cost is 2-4MB of RAM, depending on kernel
config - which is a modest cost on modern x86 systems.
Given how young the ORC unwinder code is it's not enabled by default
- but given the performance advantages the plan is to eventually make
it the default unwinder on x86.
See Documentation/x86/orc-unwinder.txt for more details.
- Remove lguest support: its intended role was that of a temporary
proof of concept for virtualization, plus its removal will enable the
reduction (removal) of the paravirt API as well, so Rusty agreed to
its removal. (Juergen Gross)
- Clean up and fix FSGS related functionality (Andy Lutomirski)
- Clean up IO access APIs (Andy Shevchenko)
- Enhance the symbol namespace (Jiri Slaby)
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (47 commits)
objtool: Handle GCC stack pointer adjustment bug
x86/entry/64: Use ENTRY() instead of ALIGN+GLOBAL for stub32_clone()
x86/fpu/math-emu: Add ENDPROC to functions
x86/boot/64: Extract efi_pe_entry() from startup_64()
x86/boot/32: Extract efi_pe_entry() from startup_32()
x86/lguest: Remove lguest support
x86/paravirt/xen: Remove xen_patch()
objtool: Fix objtool fallthrough detection with function padding
x86/xen/64: Fix the reported SS and CS in SYSCALL
objtool: Track DRAP separately from callee-saved registers
objtool: Fix validate_branch() return codes
x86: Clarify/fix no-op barriers for text_poke_bp()
x86/switch_to/64: Rewrite FS/GS switching yet again to fix AMD CPUs
selftests/x86/fsgsbase: Test selectors 1, 2, and 3
x86/fsgsbase/64: Report FSBASE and GSBASE correctly in core dumps
x86/fsgsbase/64: Fully initialize FS and GS state in start_thread_common
x86/asm: Fix UNWIND_HINT_REGS macro for older binutils
x86/asm/32: Fix regs_get_register() on segment registers
x86/xen/64: Rearrange the SYSCALL entries
x86/asm/32: Remove a bunch of '& 0xffff' from pt_regs segment reads
...
Pull perf updates from Ingo Molnar:
"Kernel side changes:
- Add branch type profiling/tracing support. (Jin Yao)
- Add the PERF_SAMPLE_PHYS_ADDR ABI to allow the tracing/profiling of
physical memory addresses, where the PMU supports it. (Kan Liang)
- Export some PMU capability details in the new
/sys/bus/event_source/devices/cpu/caps/ sysfs directory. (Andi
Kleen)
- Aux data fixes and updates (Will Deacon)
- kprobes fixes and updates (Masami Hiramatsu)
- AMD uncore PMU driver fixes and updates (Janakarajan Natarajan)
On the tooling side, here's a (limited!) list of highlights - there
were many other changes that I could not list, see the shortlog and
git history for details:
UI improvements:
- Implement a visual marker for fused x86 instructions in the
annotate TUI browser, available now in 'perf report', more work
needed to have it available as well in 'perf top' (Jin Yao)
Further explanation from one of Jin's patches:
│ ┌──cmpl $0x0,argp_program_version_hook
81.93 │ ├──je 20
│ │ lock cmpxchg %esi,0x38a9a4(%rip)
│ │↓ jne 29
│ │↓ jmp 43
11.47 │20:└─→cmpxch %esi,0x38a999(%rip)
That means the cmpl+je is a fused instruction pair and they should
be considered together.
- Record the branch type and then show statistics and info about in
callchain entries (Jin Yao)
Example from one of Jin's patches:
# perf record -g -j any,save_type
# perf report --branch-history --stdio --no-children
38.50% div.c:45 [.] main div
|
---main div.c:42 (RET CROSS_2M cycles:2)
compute_flag div.c:28 (cycles:2)
compute_flag div.c:27 (RET CROSS_2M cycles:1)
rand rand.c:28 (cycles:1)
rand rand.c:28 (RET CROSS_2M cycles:1)
__random random.c:298 (cycles:1)
__random random.c:297 (COND_BWD CROSS_2M cycles:1)
__random random.c:295 (cycles:1)
__random random.c:295 (COND_BWD CROSS_2M cycles:1)
__random random.c:295 (cycles:1)
__random random.c:295 (RET CROSS_2M cycles:9)
namespaces support:
- Add initial support for namespaces, using setns to access files in
namespaces, grabbing their build-ids, etc. (Krister Johansen)
perf trace enhancements:
- Beautify pkey_{alloc,free,mprotect} arguments in 'perf trace'
(Arnaldo Carvalho de Melo)
- Add initial 'clone' syscall args beautifier in 'perf trace'
(Arnaldo Carvalho de Melo)
- Ignore 'fd' and 'offset' args for MAP_ANONYMOUS in 'perf trace'
(Arnaldo Carvalho de Melo)
- Beautifiers for the 'cmd' arg of several ioctl types, including:
sound, DRM, KVM, vhost virtio and perf_events. (Arnaldo Carvalho de
Melo)
- Add PERF_SAMPLE_CALLCHAIN and PERF_RECORD_MMAP[2] to 'perf data'
CTF conversion, allowing CTF trace visualization tools to show
callchains and to resolve symbols (Geneviève Bastien)
- Beautify the fcntl syscall, which is an interesting one in the
sense that infrastructure had to be put in place to change the
formatters of some arguments according to the value in a previous
one, i.e. cmd dictates how arg and the syscall return will be
formatted. (Arnaldo Carvalho de Melo
perf stat enhancements:
- Use group read for event groups in 'perf stat', reducing overhead
when groups are defined in the event specification, i.e. when using
{} to enclose a list of events, asking them to be read at the same
time, e.g.: "perf stat -e '{cycles,instructions}'" (Jiri Olsa)
pipe mode improvements:
- Process tracing data in 'perf annotate' pipe mode (David
Carrillo-Cisneros)
- Add header record types to pipe-mode, now this command:
$ perf record -o - -e cycles sleep 1 | perf report --stdio --header
Will show the same as in non-pipe mode, i.e. involving a perf.data
file (David Carrillo-Cisneros)
Vendor specific hardware event support updates/enhancements:
- Update POWER9 vendor events tables (Sukadev Bhattiprolu)
- Add POWER9 PMU events Sukadev (Bhattiprolu)
- Support additional POWER8+ PVR in PMU mapfile (Shriya)
- Add Skylake server uncore JSON vendor events (Andi Kleen)
- Support exporting Intel PT data to sqlite3 with python perf
scripts, this is in addition to the postgresql support that was
already there (Adrian Hunter)"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (253 commits)
perf symbols: Fix plt entry calculation for ARM and AARCH64
perf probe: Fix kprobe blacklist checking condition
perf/x86: Fix caps/ for !Intel
perf/core, x86: Add PERF_SAMPLE_PHYS_ADDR
perf/core, pt, bts: Get rid of itrace_started
perf trace beauty: Beautify pkey_{alloc,free,mprotect} arguments
tools headers: Sync cpu features kernel ABI headers with tooling headers
perf tools: Pass full path of FEATURES_DUMP
perf tools: Robustify detection of clang binary
tools lib: Allow external definition of CC, AR and LD
perf tools: Allow external definition of flex and bison binary names
tools build tests: Don't hardcode gcc name
perf report: Group stat values on global event id
perf values: Zero value buffers
perf values: Fix allocation check
perf values: Fix thread index bug
perf report: Add dump_read function
perf record: Set read_format for inherit_stat
perf c2c: Fix remote HITM detection for Skylake
perf tools: Fix static build with newer toolchains
...
Pull RCU updates from Ingo Molnad:
"The main RCU related changes in this cycle were:
- Removal of spin_unlock_wait()
- SRCU updates
- RCU torture-test updates
- RCU Documentation updates
- Extend the sys_membarrier() ABI with the MEMBARRIER_CMD_PRIVATE_EXPEDITED variant
- Miscellaneous RCU fixes
- CPU-hotplug fixes"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (63 commits)
arch: Remove spin_unlock_wait() arch-specific definitions
locking: Remove spin_unlock_wait() generic definitions
drivers/ata: Replace spin_unlock_wait() with lock/unlock pair
ipc: Replace spin_unlock_wait() with lock/unlock pair
exit: Replace spin_unlock_wait() with lock/unlock pair
completion: Replace spin_unlock_wait() with lock/unlock pair
doc: Set down RCU's scheduling-clock-interrupt needs
doc: No longer allowed to use rcu_dereference on non-pointers
doc: Add RCU files to docbook-generation files
doc: Update memory-barriers.txt for read-to-write dependencies
doc: Update RCU documentation
membarrier: Provide expedited private command
rcu: Remove exports from rcu_idle_exit() and rcu_idle_enter()
rcu: Add warning to rcu_idle_enter() for irqs enabled
rcu: Make rcu_idle_enter() rely on callers disabling irqs
rcu: Add assertions verifying blocked-tasks list
rcu/tracing: Set disable_rcu_irq_enter on rcu_eqs_exit()
rcu: Add TPS() protection for _rcu_barrier_trace strings
rcu: Use idle versions of swait to make idle-hack clear
swait: Add idle variants which don't contribute to load average
...
This removes the restriction on the value range of the fbcon=margin:
parameter. The color value really depends on the driver being used.
Signed-off-by: David Lechner <david@lechnology.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
[b.zolnierkie: ported over fbcon changes]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Add support for STM32 Low-Power Timer, that can be used as counter
or quadrature encoder.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add documentation for STMicroelectronics STM32 Low-Power Timer
quadrature encoder and counter binding.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add documentation for STMicroelectronics STM32 Low-Power Timer Trigger
binding.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add documentation for STMicroelectronics STM32 Low-Power Timer binding.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Pull documentation updates from Jonathan Corbet:
"After a fair amount of churn in the last couple of cycles, docs are
taking it easier this time around. Lots of fixes and some new
documentation, but nothing all that radical. Perhaps the most
interesting change for many is the scripts/sphinx-pre-install tool
from Mauro; it will tell you exactly which packages you need to
install to get a working docs toolchain on your system.
There are two little patches reaching outside of Documentation/; both
just tweak kerneldoc comments to eliminate warnings and fix some
dangling doc pointers"
* 'docs-next' of git://git.lwn.net/linux: (52 commits)
Documentation/sphinx: fix kernel-doc decode for non-utf-8 locale
genalloc: Fix an incorrect kerneldoc comment
doc: Add documentation for the genalloc subsystem
assoc_array: fix path to assoc_array documentation
kernel-doc parser mishandles declarations split into lines
docs: ReSTify table of contents in core.rst
docs: process: drop git snapshots from applying-patches.rst
Documentation:input: fix typo
swap: Remove obsolete sentence
sphinx.rst: Allow Sphinx version 1.6 at the docs
docs-rst: fix verbatim font size on tables
Documentation: stable-kernel-rules: fix broken git urls
rtmutex: update rt-mutex
rtmutex: update rt-mutex-design
docs: fix minimal sphinx version in conf.py
docs: fix nested numbering in the TOC
NVMEM documentation fix: A minor typo
docs-rst: pdf: use same vertical margin on all Sphinx versions
doc: Makefile: if sphinx is not found, run a check script
docs: Fix paths in security/keys
...
- New driver for Lantiq CPU temperature sensor
- New driver for IBM CFF power supply
- New PMBus driver for TPS53679
- Add support for LM5066I lm25066 PMBus driver
- Add support for Intel VID protocol VR13 to PMBus drivers
- Add support for CAT34TS02C, GT30TS00, GT34TS02, and CAT34TS04 to jc42 driver
- Cleanup and minor improvements in several drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJZrJttAAoJEMsfJm/On5mBwmsP/2fC8Khuc7cGtGYpUmOLDP7y
QjLe0Bf310r2Zs02W3+a9WExymYk/1NpireFlbsganuCCk3ooKxhvrP83Y/09N30
mhKDenVyq8gTL1YdXimUwZZZa9X/yMNf5xhdaTd3393hLYdb1dwgwjQu7V9VALFY
i2Zwz0zqjZeMkvbI06LaoTvRHtPbFw8u4/fPPEoipzw19RfM7T+1hofSVjGYQ5U+
amr4lZzPI3UkOYjfKZwq4vokZVybZfvQWl+LxY/TLQLmrqcKKNV05hmindg6g5mc
rpBGyM54higGSyyWby8OpoeFJ5rEfLQzTDBlGIZqlhOz6Drbd3KBj5W+Er97+l+h
9NYdJwmRU25at+BIDbZ/FrTY+gc+xdTX/N5TJWfIoxmlcZwFLIUKIX9+5p0SBJj4
JPpDCiR1u4rJPB2B5HQFxGkhQpnVOqtN9hCmj+fXg9mkigjImHuxErAOABcOoJpZ
9CMlLuteg3PlD01T4qQXJKvxsx68f7bl4HFyHC3leoD3AiWF4B4kwaft14Infiqh
f1Zk3QUUxqRdPaDNCX8my0XEtfqmpTU+qow8yaKz7YCaWeu4MDBY8nkJhrE5mma4
YjmfH5A4Gvm6cLJTBQDUC09Q46G+j780SWQYyJxKSnyv5u5mvmz6m69kubZNvsjX
xKsJjrdo5bBK3hWzznCv
=DZJP
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- new drivers:
- Lantiq CPU temperature sensor
- IBM CFF power supply
- TPS53679 PMBus driver
- new support:
- LM5066I (lm25066 PMBus driver)
- Intel VID protocol VR13 (PMBus drivers)
- CAT34TS02C, GT30TS00, GT34TS02, and CAT34TS04 (jc42 driver)
- cleanup and minor improvements in several drivers
* tag 'hwmon-for-linus-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (36 commits)
hwmon: (ltq-cputemp) add cpu temp sensor driver
hwmon: (ltq-cputemp) add devicetree bindings documentation
hwmon: (pmbus) Add support for Texas Instruments tps53679 device
hwmon: (asc7621) make several arrays static const
hwmon: (pmbus/lm25066) Add support for TI LM5066I
hwmon: (pmbus/lm25066) Offset coefficient depends on CL
hwmon: (pmbus) Add support for Intel VID protocol VR13
Documentation: hwmon: Document the IBM CFF power supply
hwmon: (pmbus) Add IBM Common Form Factor (CFF) power supply driver
dt-bindings: hwmon: Document the IBM CCF power supply version 1
hwmon: (ftsteutates) constify i2c_device_id
hwmon: da9052: Add support for TSI channel
mfd: da9052: Make touchscreen registration optional
hwmon: da9052: Replace S_IRUGO with 0444
mfd: da9052: Add register details for TSI
hwmon: (aspeed-pwm) add THERMAL dependency
hwmon: (pmbus) Add debugfs for status registers
hwmon: (aspeed-pwm-tacho) cooling device support.
Documentation: dt-bindings: aspeed-pwm-tacho cooling device.
hwmon: (pmbus): Add generic alarm bit for iin and pin
...
- Lots of hfi1 driver updates (mixed with a few qib and core updates as
well)
- rxe updates
- various mlx updates
- Set default roce type to RoCEv2
- Several larger fixes for bnxt_re that were too big for -rc
- Several larger fixes for qedr that, likewise, were too big for -rc
- Misc core changes
- Make the hns_roce driver compilable on arches other than aarch64 so we
can more easily debug build issues related to it
- Add rdma-netlink infrastructure updates
- Add automatic IRQ affinity infrastructure
- Add 32bit lid support
- Lots of misc fixes across the subsystem from random people
- Autoloading of RDMA netlink modules
- PCI pool cleanups from Romain Perier
- mlx5 driver feature additions and fixes
- Hardware tag matchine feature
- Fix sleeping in atomic when resolving roce ah
- Add experimental ioctl interface as posted to linux-api@
-----BEGIN PGP SIGNATURE-----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=2ntC
-----END PGP SIGNATURE-----
Merge tag 'for-linus-ioctl' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"This is a big pull request.
Of note is that I'm sending you the new ioctl API for the rdma
subsystem. We put it up on linux-api@, but didn't get much response.
The API is complex, but it solves two different problems in one go:
1) The bi-directional nature of the RDMA file write calls, which
created the security hole we had to handle (and for which the fix
is now causing problems for systems in production, we were a bit
over zealous in the fix and the ability to open a device, then
fork, then create new queue pairs on the device and use them is
broken).
2) The bloat caused by different vendors implementing extensions to
the base verbs API. Each vendor's hardware is slightly different,
and the hardware might be suitable for one extension but not
another.
By the time we add generic extensions for all the different ways
that the different hardware can offload things, the API becomes
bloated. Things like our completion structs have started to exceed
a cache line in size because of all the elements needed to support
this. That in turn shows up heavily in the performance graphs with
a noticable drop in performance on 100Gigabit links as our
completion structs go from occupying one cache line to 1+.
This API makes things like the completion structs modular in a
very similar way to netlink so that your structs can only include
the items needed for the offloads/features you are actually using
on a given queue pair. In that way we support everything, but only
use what we need, and our structs stay smaller.
The ioctl API is better explained by the posting on linux-api@ than I
can explain it here, so I'll just leave it at that.
The rest of the pull request is typical stuff.
Updates for 4.14 kernel merge window
- Lots of hfi1 driver updates (mixed with a few qib and core updates
as well)
- rxe updates
- various mlx updates
- Set default roce type to RoCEv2
- Several larger fixes for bnxt_re that were too big for -rc
- Several larger fixes for qedr that, likewise, were too big for -rc
- Misc core changes
- Make the hns_roce driver compilable on arches other than aarch64 so
we can more easily debug build issues related to it
- Add rdma-netlink infrastructure updates
- Add automatic IRQ affinity infrastructure
- Add 32bit lid support
- Lots of misc fixes across the subsystem from random people
- Autoloading of RDMA netlink modules
- PCI pool cleanups from Romain Perier
- mlx5 driver feature additions and fixes
- Hardware tag matchine feature
- Fix sleeping in atomic when resolving roce ah
- Add experimental ioctl interface as posted to linux-api@"
* tag 'for-linus-ioctl' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (328 commits)
IB/core: Expose ioctl interface through experimental Kconfig
IB/core: Assign root to all drivers
IB/core: Add completion queue (cq) object actions
IB/core: Add legacy driver's user-data
IB/core: Export ioctl enum types to user-space
IB/core: Explicitly destroy an object while keeping uobject
IB/core: Add macros for declaring methods and attributes
IB/core: Add uverbs merge trees functionality
IB/core: Add DEVICE object and root tree structure
IB/core: Declare an object instead of declaring only type attributes
IB/core: Add new ioctl interface
RDMA/vmw_pvrdma: Fix a signedness
RDMA/vmw_pvrdma: Report network header type in WC
IB/core: Add might_sleep() annotation to ib_init_ah_from_wc()
IB/cm: Fix sleeping in atomic when RoCE is used
IB/core: Add support to finalize objects in one transaction
IB/core: Add a generic way to execute an operation on a uobject
Documentation: Hardware tag matching
IB/mlx5: Support IB_SRQT_TM
net/mlx5: Add XRQ support
...
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next
tree. Basically, updates to the conntrack core, enhancements for
nf_tables, conversion of netfilter hooks from linked list to array to
improve memory locality and asorted improvements for the Netfilter
codebase. More specifically, they are:
1) Add expection to hashes after timer initialization to prevent
access from another CPU that walks on the hashes and calls
del_timer(), from Florian Westphal.
2) Don't update nf_tables chain counters from hot path, this is only
used by the x_tables compatibility layer.
3) Get rid of nested rcu_read_lock() calls from netfilter hook path.
Hooks are always guaranteed to run from rcu read side, so remove
nested rcu_read_lock() where possible. Patch from Taehee Yoo.
4) nf_tables new ruleset generation notifications include PID and name
of the process that has updated the ruleset, from Phil Sutter.
5) Use skb_header_pointer() from nft_fib, so we can reuse this code from
the nf_family netdev family. Patch from Pablo M. Bermudo.
6) Add support for nft_fib in nf_tables netdev family, also from Pablo.
7) Use deferrable workqueue for conntrack garbage collection, to reduce
power consumption, from Patch from Subash Abhinov Kasiviswanathan.
8) Add nf_ct_expect_iterate_net() helper and use it. From Florian
Westphal.
9) Call nf_ct_unconfirmed_destroy only from cttimeout, from Florian.
10) Drop references on conntrack removal path when skbuffs has escaped via
nfqueue, from Florian.
11) Don't queue packets to nfqueue with dying conntrack, from Florian.
12) Constify nf_hook_ops structure, from Florian.
13) Remove neededlessly branch in nf_tables trace code, from Phil Sutter.
14) Add nla_strdup(), from Phil Sutter.
15) Rise nf_tables objects name size up to 255 chars, people want to use
DNS names, so increase this according to what RFC 1035 specifies.
Patch series from Phil Sutter.
16) Kill nf_conntrack_default_on, it's broken. Default on conntrack hook
registration on demand, suggested by Eric Dumazet, patch from Florian.
17) Remove unused variables in compat_copy_entry_from_user both in
ip_tables and arp_tables code. Patch from Taehee Yoo.
18) Constify struct nf_conntrack_l4proto, from Julia Lawall.
19) Constify nf_loginfo structure, also from Julia.
20) Use a single rb root in connlimit, from Taehee Yoo.
21) Remove unused netfilter_queue_init() prototype, from Taehee Yoo.
22) Use audit_log() instead of open-coding it, from Geliang Tang.
23) Allow to mangle tcp options via nft_exthdr, from Florian.
24) Allow to fetch TCP MSS from nft_rt, from Florian. This includes
a fix for a miscalculation of the minimal length.
25) Simplify branch logic in h323 helper, from Nick Desaulniers.
26) Calculate netlink attribute size for conntrack tuple at compile
time, from Florian.
27) Remove protocol name field from nf_conntrack_{l3,l4}proto structure.
From Florian.
28) Remove holes in nf_conntrack_l4proto structure, so it becomes
smaller. From Florian.
29) Get rid of print_tuple() indirection for /proc conntrack listing.
Place all the code in net/netfilter/nf_conntrack_standalone.c.
Patch from Florian.
30) Do not built in print_conntrack() if CONFIG_NF_CONNTRACK_PROCFS is
off. From Florian.
31) Constify most nf_conntrack_{l3,l4}proto helper functions, from
Florian.
32) Fix broken indentation in ebtables extensions, from Colin Ian King.
33) Fix several harmless sparse warning, from Florian.
34) Convert netfilter hook infrastructure to use array for better memory
locality, joint work done by Florian and Aaron Conole. Moreover, add
some instrumentation to debug this.
35) Batch nf_unregister_net_hooks() calls, to call synchronize_net once
per batch, from Florian.
36) Get rid of noisy logging in ICMPv6 conntrack helper, from Florian.
37) Get rid of obsolete NFDEBUG() instrumentation, from Varsha Rao.
38) Remove unused code in the generic protocol tracker, from Davide
Caratti.
I think I will have material for a second Netfilter batch in my queue if
time allow to make it fit in this merge window.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=5fxW
-----END PGP SIGNATURE-----
Merge tag 'drm-for-v4.14' of git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 4.14 merge window.
I'm sending this early, as my continuing journey into fatherhood is
occurring really soon now, I'm going to be mostly useless for the next
couple of weeks, though I may be able to read email, I doubt I'll be
doing much patch applications or git sending. If anything urgent pops
up I've asked Daniel/Jani/Alex/Sean to try and direct stuff towards
you.
Outside drm changes:
Some rcar-du updates that touch the V4L tree, all acks should be in
place. It adds one export to the radix tree code for new i915 use
case. There are some minor AGP cleanups (don't see that too often).
Changes to the vbox driver in staging to avoid breaking compilation.
Summary:
core:
- Atomic helper fixes
- Atomic UAPI fixes
- Add YCBCR 4:2:0 support
- Drop set_busid hook
- Refactor fb_helper locking
- Remove a bunch of internal APIs
- Add a bunch of better default handlers
- Format modifier/blob plane property added
- More internal header refactoring
- Make more internal API names consistent
- Enhanced syncobj APIs (wait/signal/reset/create signalled)
bridge:
- Add Synopsys Designware MIPI DSI host bridge driver
tiny:
- Add Pervasive Displays RePaper displays
- Add support for LEGO MINDSTORMS EV3 LCD
i915:
- Lots of GEN10/CNL support patches
- drm syncobj support
- Skylake+ watermark refactoring
- GVT vGPU 48-bit ppgtt support
- GVT performance improvements
- NOA change ioctl
- CCS (color compression) scanout support
- GPU reset improvements
amdgpu:
- Initial hugepage support
- BO migration logic rework
- Vega10 improvements
- Powerplay fixes
- Stop reprogramming the MC
- Fixes for ACP audio on stoney
- SR-IOV fixes/improvements
- Command submission overhead improvements
amdkfd:
- Non-dGPU upstreaming patches
- Scratch VA ioctl
- Image tiling modes
- Update PM4 headers for new firmware
- Drop all BUG_ONs.
nouveau:
- GP108 modesetting support.
- Disable MSI on big endian.
vmwgfx:
- Add fence fd support.
msm:
- Runtime PM improvements
exynos:
- NV12MT support
- Refactor KMS drivers
imx-drm:
- Lock scanout channel to improve memory bw
- Cleanups
etnaviv:
- GEM object population fixes
tegra:
- Prep work for Tegra186 support
- PRIME mmap support
sunxi:
- HDMI support improvements
- HDMI CEC support
omapdrm:
- HDMI hotplug IRQ support
- Big driver cleanup
- OMAP5 DSI support
rcar-du:
- vblank fixes
- VSP1 updates
arcgpu:
- Minor fixes
stm:
- Add STM32 DSI controller driver
dw_hdmi:
- Add support for Rockchip RK3399
- HDMI CEC support
atmel-hlcdc:
- Add 8-bit color support
vc4:
- Atomic fixes
- New ioctl to attach a label to a buffer object
- HDMI CEC support
- Allow userspace to dictate rendering order on submit ioctl"
* tag 'drm-for-v4.14' of git://people.freedesktop.org/~airlied/linux: (1074 commits)
drm/syncobj: Add a signal ioctl (v3)
drm/syncobj: Add a reset ioctl (v3)
drm/syncobj: Add a syncobj_array_find helper
drm/syncobj: Allow wait for submit and signal behavior (v5)
drm/syncobj: Add a CREATE_SIGNALED flag
drm/syncobj: Add a callback mechanism for replace_fence (v3)
drm/syncobj: add sync obj wait interface. (v8)
i915: Use drm_syncobj_fence_get
drm/syncobj: Add a race-free drm_syncobj_fence_get helper (v2)
drm/syncobj: Rename fence_get to find_fence
drm: kirin: Add mode_valid logic to avoid mode clocks we can't generate
drm/vmwgfx: Bump the version for fence FD support
drm/vmwgfx: Add export fence to file descriptor support
drm/vmwgfx: Add support for imported Fence File Descriptor
drm/vmwgfx: Prepare to support fence fd
drm/vmwgfx: Fix incorrect command header offset at restart
drm/vmwgfx: Support the NOP_ERROR command
drm/vmwgfx: Restart command buffers after errors
drm/vmwgfx: Move irq bottom half processing to threads
drm/vmwgfx: Don't use drm_irq_[un]install
...
* pm-sleep:
ACPI / PM: Check low power idle constraints for debug only
PM / s2idle: Rename platform operations structure
PM / s2idle: Rename ->enter_freeze to ->enter_s2idle
PM / s2idle: Rename freeze_state enum and related items
PM / s2idle: Rename PM_SUSPEND_FREEZE to PM_SUSPEND_TO_IDLE
ACPI / PM: Prefer suspend-to-idle over S3 on some systems
platform/x86: intel-hid: Wake up Dell Latitude 7275 from suspend-to-idle
PM / suspend: Define pr_fmt() in suspend.c
PM / suspend: Use mem_sleep_labels[] strings in messages
PM / sleep: Put pm_test under CONFIG_PM_SLEEP_DEBUG
PM / sleep: Check pm_wakeup_pending() in __device_suspend_noirq()
PM / core: Add error argument to dpm_show_time()
PM / core: Split dpm_suspend_noirq() and dpm_resume_noirq()
PM / s2idle: Rearrange the main suspend-to-idle loop
PM / timekeeping: Print debug messages when requested
PM / sleep: Mark suspend/hibernation start and finish
PM / sleep: Do not print debug messages by default
PM / suspend: Export pm_suspend_target_state
* intel_pstate:
cpufreq: intel_pstate: Shorten a couple of long names
cpufreq: intel_pstate: Simplify intel_pstate_adjust_pstate()
cpufreq: intel_pstate: Improve IO performance with per-core P-states
cpufreq: intel_pstate: Drop INTEL_PSTATE_HWP_SAMPLING_INTERVAL
cpufreq: intel_pstate: Drop ->update_util from pstate_funcs
cpufreq: intel_pstate: Do not use PID-based P-state selection
* pm-cpufreq: (33 commits)
cpufreq: imx6q: Fix imx6sx low frequency support
cpufreq: speedstep-lib: make several arrays static, makes code smaller
cpufreq: ti: Fix 'of_node_put' being called twice in error handling path
cpufreq: dt-platdev: Drop few entries from whitelist
cpufreq: dt-platdev: Automatically create cpufreq device with OPP v2
ARM: ux500: don't select CPUFREQ_DT
cpufreq: Convert to using %pOF instead of full_name
cpufreq: Cap the default transition delay value to 10 ms
cpufreq: dbx500: Delete obsolete driver
mfd: db8500-prcmu: Get rid of cpufreq dependency
cpufreq: enable the DT cpufreq driver on the Ux500
cpufreq: Loongson2: constify platform_device_id
cpufreq: dt: Add r8a7796 support to to use generic cpufreq driver
cpufreq: remove setting of policy->cpu in policy->cpus during init
cpufreq: mediatek: add support of cpufreq to MT7622 SoC
cpufreq: mediatek: add cleanups with the more generic naming
cpufreq: rcar: Add support for R8A7795 SoC
cpufreq: dt: Add rk3328 compatible to use generic cpufreq driver
cpufreq: s5pv210: add missing of_node_put()
cpufreq: Allow dynamic switching with CPUFREQ_ETERNAL latency
...
* pm-core:
PM / wakeup: Set power.can_wakeup if wakeup_sysfs_add() fails
* pm-opp:
PM / OPP: Fix get sharing CPUs when hotplug is used
PM / OPP: OF: Use pr_debug() instead of pr_err() while adding OPP table
* pm-domains:
PM / Domains: Convert to using %pOF instead of full_name
PM / Domains: Extend generic power domain debugfs
PM / Domains: Add time accounting to various genpd states
* pm-cpu:
PM / CPU: replace raw_notifier with atomic_notifier
* pm-avs:
PM / AVS: rockchip-io: add io selectors and supplies for RV1108
A couple of late-arriving fixes before final 4.13:
- A few reverts of DT bindings on Allwinner for their ethernet
driver. Discussion didn't converge, and since bindings are considered
ABI it makes sense to revert instead of having to support two bindings
long-term.
- A fix to enumerate GPIOs properly on Marvell Armada AP806
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=3QBk
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A couple of late-arriving fixes before final 4.13:
- A few reverts of DT bindings on Allwinner for their ethernet
driver. Discussion didn't converge, and since bindings are
considered ABI it makes sense to revert instead of having to
support two bindings long-term.
- A fix to enumerate GPIOs properly on Marvell Armada AP806"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: dts: marvell: fix number of GPIOs in Armada AP806 description
arm: dts: sunxi: Revert EMAC changes
arm64: dts: allwinner: Revert EMAC changes
dt-bindings: net: Revert sun8i dwmac binding
This is a revert of the EMAC bindings. The discussion has not settled down
yet on a proper representation of the PHY, and therefore we cannot commit
to a binding yet
-----BEGIN PGP SIGNATURE-----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=0xy6
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.13-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt64
Allwinner fixes for 4.13, take 3
This is a revert of the EMAC bindings. The discussion has not settled down
yet on a proper representation of the PHY, and therefore we cannot commit
to a binding yet
* tag 'sunxi-fixes-for-4.13-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm: dts: sunxi: Revert EMAC changes
arm64: dts: allwinner: Revert EMAC changes
dt-bindings: net: Revert sun8i dwmac binding
arm64: allwinner: h5: fix pinctrl IRQs
arm64: allwinner: a64: sopine: add missing ethernet0 alias
arm64: allwinner: a64: pine64: add missing ethernet0 alias
arm64: allwinner: a64: bananapi-m64: add missing ethernet0 alias
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts
arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts
This is a revert of the EMAC bindings. The discussion has not settled down
yet on a proper representation of the PHY, and therefore we cannot commit
to a binding yet
-----BEGIN PGP SIGNATURE-----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=0xy6
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.13-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner fixes for 4.13, take 3
This is a revert of the EMAC bindings. The discussion has not settled down
yet on a proper representation of the PHY, and therefore we cannot commit
to a binding yet
* tag 'sunxi-fixes-for-4.13-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm: dts: sunxi: Revert EMAC changes
arm64: dts: allwinner: Revert EMAC changes
dt-bindings: net: Revert sun8i dwmac binding
arm64: allwinner: h5: fix pinctrl IRQs
arm64: allwinner: a64: sopine: add missing ethernet0 alias
arm64: allwinner: a64: pine64: add missing ethernet0 alias
arm64: allwinner: a64: bananapi-m64: add missing ethernet0 alias
Signed-off-by: Olof Johansson <olof@lixom.net>
Since gclk (generated-clk) is now able to determine the rate of the
audio_pll, there is no need for classd to have a direct phandle to the
audio_pll while already having a phandle to gclk.
This binding is used by no board in mainline so it is safe to be
modified.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This new clock driver set allows to have a fractional divided clock that
would generate a precise clock particularly suitable for audio
applications.
The main audio pll clock has two children clocks: one that is connected
to the PMC, the other that can directly drive a pad. As these two routes
have different enable bits and different dividers and divider formulas,
they are handled by two different drivers.
This adds the audio plls (frac, pad and pmc) to the compatible list of
at91 clocks in DT binding.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
In addition to using GLINK for communication with the RPM it can be
used ontop of SMEM for communicating with remoteprocs, extend the
binding to also describe this case and reference the GLINK binding from
the affected remoteproc bindings.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This initial port adds support of ARC HS Development Kit board with some
basic features such serial port, USB, SD/MMC and Ethernet.
Essentially we run Linux kernel on all 4 cores (i.e. utilize SMP) and
heavily use IO Coherency for speeding-up DMA-aware peripherals.
Note as opposed to other ARC boards we link Linux kernel to
0x9000_0000 intentionally because cores 1 and 3 configured with DCCM
situated at our more usual link base 0x8000_0000. We still can use
memory region starting at 0x8000_0000 as we reallocate DCCM in our
platform code.
Note that PAE remapping for DMA clients does not work due to an RTL bug,
so CREG_PAE register must be programmed to all zeroes, otherwise it will
cause problems with DMA to/from peripherals even if PAE40 is not used.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Documentation for this feature was missing from the patchset.
Copied a lot from the netdev 2.1 paper, addressing some small
interface changes since then.
Changes
v1 -> v2
- change email discussion URL format
- clarify that u32 counter is per-syscall, unsigned and
wraps after UINT_MAX calls
- describe errno on send failure specific to MSG_ZEROCOPY
- a few very minor rewordings
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the preferred generic node name in the example.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Rob Herring <robh@kernel.org>
A link interrupt can be described. Document this valid interrupt name.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Fix memory leaks in the core
* Remove unused NAND locking support
* Rename nand.h into rawnand.h (preparing support for spi NANDs)
* Use NAND_MAX_ID_LEN where appropriate
* Fix support for 20nm Hynix chips
* Fix support for Samsung and Hynix SLC NANDs
and the following driver changes:
* Various cleanup, improvements and fixes in the qcom driver
* Fixes for bugs detected by various static code analysis tools
* Fix mxc ooblayout definition
* Add a new part_parsers to tmio and sharpsl platform data in order to
define a custom list of partition parsers
* Request the reset line in exclusive mode in the sunxi driver
* Fix a build error in the orion-nand driver when compiled for ARMv4
* Allow 64-bit mvebu platforms to select the PXA3XX driver
-----BEGIN PGP SIGNATURE-----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=bC1+
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.14' of git://git.infradead.org/l2-mtd into mtd/next
From Boris:
"
This pull request contains the following core changes:
* Fix memory leaks in the core
* Remove unused NAND locking support
* Rename nand.h into rawnand.h (preparing support for spi NANDs)
* Use NAND_MAX_ID_LEN where appropriate
* Fix support for 20nm Hynix chips
* Fix support for Samsung and Hynix SLC NANDs
and the following driver changes:
* Various cleanup, improvements and fixes in the qcom driver
* Fixes for bugs detected by various static code analysis tools
* Fix mxc ooblayout definition
* Add a new part_parsers to tmio and sharpsl platform data in order to
define a custom list of partition parsers
* Request the reset line in exclusive mode in the sunxi driver
* Fix a build error in the orion-nand driver when compiled for ARMv4
* Allow 64-bit mvebu platforms to select the PXA3XX driver
"
Add devicetree bindings documentation file for Cirrus
Logic CS43130 codec.
Signed-off-by: Li Xu <li.xu@cirrus.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some CPU drivers (e. g. davinci-mcasp) may require the system clock to
be configured as OUT, while there's no good way currently to set
SND_SOC_CLK_OUT in simple-soc driver if the clock is fixed-rate.
This patch makes asoc_simple_card_init_dai() initialize clock to
SND_SOCK_CLK_OUT if explicitly stated in the relevant dts file. This
change is transparent and doesn't change the default behavior.
Signed-off-by: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DMA_MEMORY_IO was never used in the tree, so remove it. That means there is
no need for the DMA_MEMORY_MAP flag either now, so remove it as well and
change dma_declare_coherent_memory to return a normal errno value.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
This patch enables clocks for STM32H743 boards.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
for MFD changes:
Acked-by: Lee Jones <lee.jones@linaro.org>
for DT-Bindings
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add basic clock data for Socionext's new SoC PXs3.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The RTC can output its 32kHz clock outside of the SoC, for example to clock
a WiFi chip.
Create a new clock that other devices will be able to retrieve, while
maintaining the DT stability by providing a default name for that clock if
clock-output-names doesn't list one.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add documentation for DT binding of Goldfish RTC driver. The compatible
string used by OS for binding the driver is "google,goldfish-rtc".
Signed-off-by: Miodrag Dinic <miodrag.dinic@imgtec.com>
Signed-off-by: Goran Ferenc <goran.ferenc@imgtec.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@imgtec.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Many users have reported the lack of an HOWTO for properly configuring
bfq as a function of the goal one wants to achieve (max
responsiveness, max throughput, ...). In fact, all needed details are
already provided in the documentation file bfq-iosched.txt. Yet the
document lacks guidance on which parameter descriptions to look
at. This commit adds some simple direction.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Reviewed-by: Jeremy Hickman <jeremywh7@gmail.com>
Reviewed-by: Laurentiu Nicola <lnicola@dend.ro>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In addition to containing some typos and stale sentences, the file
bfq-iosched.txt still mentioned a set of sysfs parameters that have
been removed from this version of bfq. This commit fixes all these
issues.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Reviewed-by: Jeremy Hickman <jeremywh7@gmail.com>
Reviewed-by: Laurentiu Nicola <lnicola@dend.ro>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
On python3, Popen() universal_newlines=True converts the subprocess
stdout to unicode text using a codec based on user preferences. Given
LANG indicating ascii and utf-8 stdout from the subprocess, you'd get:
WARNING: kernel-doc '../scripts/kernel-doc -rst -enable-lineno
../drivers/media/dvb-core/demux.h' processing failed with: 'ascii' codec can't
decode byte 0xe2 in position 6368: ordinal not in range(128)
Fix this by dropping universal_newlines=True and replacing the implicit
LANG specific decode with an explicit utf-8 decode. This also gets rid
of the annoying conditional code for python 2 vs. 3.
Fixes: ba35018593 ("Documentation/sphinx: fix kernel-doc extension on python3")
Reference: http://mid.mail-archive.com/54c23e8e-89c0-5cea-0dcc-e938952c5642@infradead.org
Reported-and-tested-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
- irqchip-specific part of the monster GICv4 series
- new UniPhier AIDET irqchip driver
- new variants of some Freescale MSI widget
- blanket removal of of_node->full_name in printk
- random collection of fixes
-----BEGIN PGP SIGNATURE-----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=3ZS3
-----END PGP SIGNATURE-----
Merge tag 'irqchip-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates for 4.14 from Marc Zyngier:
- irqchip-specific part of the monster GICv4 series
- new UniPhier AIDET irqchip driver
- new variants of some Freescale MSI widget
- blanket removal of of_node->full_name in printk
- random collection of fixes
Conversion of the last two SoCs (A10, A20) to the sunxi-ng framework.
-----BEGIN PGP SIGNATURE-----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=Wce+
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clk-for-4.14-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into clk-next
Pull more Allwinner clock changes from Maxime Ripard:
* Conversion of the last two SoCs (A10, A20) to the sunxi-ng framework
* tag 'sunxi-clk-for-4.14-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
clk: sunxi-ng: Add sun4i/sun7i CCU driver
dt-bindings: List devicetree binding for the CCU of Allwinner A10
dt-bindings: List devicetree binding for the CCU of Allwinner A20
This is board specific info so it should come from board config, such
as devicetree.
I've chosen to prefix these with "fcs," treating them as fusb302 driver
specific for now. We may want to revisit this and replace these with
properties which are part of a (to be written) generic type-c controller
devicetree binding.
Since this commit adds new dt-properties it also adds devicetree-bindings
documentation (which so far was absent for the fusb302 driver).
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: devicetree@vger.kernel.org
Cc: "Yueyao (Nathan) Zhu" <yueyao@google.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mt8173-mtu3.txt actually holds the bindings for all mediatek
SoCs with usb3 DRD IP, so add a generic compatible and change the
name to mediatek,mtu3.txt.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mt8173-xhci.txt actually holds the bindings for all mediatek
SoCs with xHCI controller, so add a generic compatible and change
the name to mediatek,mtk-xhci.txt to reflect that.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A MSI controller of LS1043a v1.0 only includes one MSIR and
is assigned one GIC interrupt. In order to support affinity,
LS1043a v1.1 MSI is assigned 4 MSIRs and 4 GIC interrupts.
But the MSIR has the different offset and only supports 8 MSIs.
The bits between variable bit_start and bit_end in structure
ls_scfg_msir are used to show 8 MSI interrupts. msir_irqs and
msir_base are added to describe the difference of MSI between
LS1043a v1.1 and other SoCs.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The patch is to fix typo of the Layerscape SCFG MSI dts compatible
strings. "1" is replaced by "l".
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This adds the device tree binding documentation for the mediatek thermal
controller found on Mediatek MT2712.
Signed-off-by: Louis Yu <louis.yu@mediatek.com>
Reviewed-by: Dawei Chien <dawei.chien@mediatek.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
In aic3x class of devices Output Common-Mode Voltage can be configured for
better analog performance.
The OCMV value depends on the Analog and digital domain power supply
voltage configuration.
The default OCMV of 1.35V gives best performance when AVDD is around 2.7V
and DVDD is 1.525V, but for higher AVDD/DVDD higher OCMV setting is
recommended.
The patch gives an automatic way of guessing the best OCMV which can be
overwritten by a DT parameter if needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the binding documentation for Spreadtrum SC9860 pin
controller device.
Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In some scenarios, we should set some pins as input/output/pullup/pulldown
when the specified system goes into deep sleep mode, then when the system
goes into deep sleep mode, these pins will be set automatically by hardware.
That means some pins are not controlled by any specific driver in the OS, but
need to be controlled when entering sleep mode. Thus we introduce one sleep
state config into pinconf-generic for users to configure.
Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
HSDK board manages its clocks using various PLLs. These PLL have same
dividers and corresponding control registers mapped to different addresses.
So we add one common driver for such PLLs.
Each PLL on HSDK board consists of three dividers: IDIV, FBDIV and
ODIV. Output clock value is managed using these dividers.
We add pre-defined tables with supported rate values and appropriate
configurations of IDIV, FBDIV and ODIV for each value.
As of today we add support for PLLs that generate clock for the
HSDK arc cpus, system, ddr, AXI tunnel and hdmi.
By this patch we add support for several plls (arc cpus pll and others),
so we had to use two different init types: CLK_OF_DECLARE for arc cpus pll
and regular probing for others plls.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Implement vas_init() and vas_exit() functions for a new VAS module.
This VAS module is essentially a library for other device drivers
and kernel users of the NX coprocessors like NX-842 and NX-GZIP.
In the future this will be extended to add support for user space
to access the NX coprocessors.
VAS is currently only supported with 64K page size.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There are two typos in the document, netvsc.txt,
regarding UDP hashing level. This patch fixes them.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Genalloc/genpool has kerneldoc comments, but nothing has ever been pulled
into the docs themselves. Here's a first attempt, repurposed from an
article I wrote at https://lwn.net/Articles/729653/.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The Marvell Armada 7K/8K SoCs contains an hardware block called COMPHY
that provides a number of shared PHYs used by various interfaces in the
SoC: network, SATA, PCIe, etc. This Device Tree binding allows to
describe this COMPHY hardware block.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sphinx will now generate the table of contents automatically, which
avoids having the ToC getting out of sync with the rest of the document.
Signed-off-by: Josh Holland <anowlcalledjosh@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Drop all references to git daily snapshots of Linux mainline git tree
since they are no longer generated.
Drop the "Last update" info since 'git log' is a better source of that
info and since the Last update date is not being updated.
Yes, I read that this file is obsolete, but it still has some useful
information in it.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Add internal PCI bridge support for r8a7743/5 SoC. The Renesas RZ/G1[ME]
(R8A7743/5) internal PCI bridge is identical to the R-Car Gen2 family.
This doesn't change the driver, so it does nothing by itself. But it does
mean that checkpatch won't complain about a future patch that adds
"renesas,pci-r8a7743" to a DT, which helps ensure that shipped DTs use
documented compatibility strings.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
[bhelgaas: add explanatory note]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
RmNet driver provides a transport agnostic MAP (multiplexing and
aggregation protocol) support in embedded module. Module provides
virtual network devices which can be attached to any IP-mode
physical device. This will be used to provide all MAP functionality
on future hardware in a single consistent location.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document STM32 VREFBUF (voltage reference buffer) which can be used as
voltage reference for ADCs, DACs and external components.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Nodes without reg properties must not have unit addresses:
Warning (unit_address_vs_reg): Node .../rcar_sound,dvc/dvc@0 has a unit name, but no reg property
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
The TI LM5066I hotswap controller is a more accurate version of the
LM5066 device already supported. It has different measurement conversion
coefficients than the LM5066, so it needs to be recognized as a
different device.
Signed-off-by: Xo Wang <xow@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add controller support for MT2712/MT7622 and update related properties.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
To accommodate other SoC generations, regroup specific properties by SoC,
and remove redundant descriptions.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
[bhelgaas: split into a rename patch and a cleanup patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
To accommodate other SoC generations, rename mediatek,mt7623-pcie.txt to
mediatek-pcie.txt.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
[bhelgaas: split rename to separate patch so updates are obvious]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Add support for r8a7743/5 SoC. Renesas RZ/G1[ME] (R8A7743/5) SDHI
is identical to the R-Car Gen2 family.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The third MMC controller (MMC2) on the Allwinner A83T SoC is slightly
different. It supports a wider 8-bit bus, has a dedicated controllable
reset pin for eMMC, and a "new timing mode" which is supposed to deliver
better signals and thus better performance.
Add a compatible for this one to use the new timing mode not found in the
other controllers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is a revert of the EMAC bindings. The discussion has not settled down
yet on a proper representation of the PHY, and therefore we cannot commit
to a binding yet
-----BEGIN PGP SIGNATURE-----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=0xy6
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.13-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into fixes
Allwinner fixes for 4.13, take 3
This is a revert of the EMAC bindings. The discussion has not settled down
yet on a proper representation of the PHY, and therefore we cannot commit
to a binding yet
* tag 'sunxi-fixes-for-4.13-3' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm: dts: sunxi: Revert EMAC changes
arm64: dts: allwinner: Revert EMAC changes
dt-bindings: net: Revert sun8i dwmac binding
Signed-off-by: Olof Johansson <olof@lixom.net>
Add description for a new family SoC from Marvell: Armada-8KP.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlmeipsACgkQCwYYjhRyO9UnEACcDuFAUJNT2eth5lYMHoHcvMLf
x7QAnjqghjBpm7nYOutsYPY5gwz/YYC6
=+kES
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.14-3' of git://git.infradead.org/linux-mvebu into next/dt64
mvebu dt64 for 4.14 (part 3)
Add description for a new family SoC from Marvell: Armada-8KP.
* tag 'mvebu-dt64-4.14-3' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: add Device Tree files for Armada-8KP
Signed-off-by: Olof Johansson <olof@lixom.net>
Florian reported UDP xmit drops that could be root caused to the
too small neigh limit.
Current limit is 64 KB, meaning that even a single UDP socket would hit
it, since its default sk_sndbuf comes from net.core.wmem_default
(~212992 bytes on 64bit arches).
Once ARP/ND resolution is in progress, we should allow a little more
packets to be queued, at least for one producer.
Once neigh arp_queue is filled, a rogue socket should hit its sk_sndbuf
limit and either block in sendmsg() or return -EAGAIN.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ls2088a PCIe controller's register addresses are different from
ls2080a, so add a match entry to identify ls2088a PCIe.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Minghuan Lian <minghuan.Lian@nxp.com>
Explain that the patch queue in patchwork should not be touched by patch
submitters.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update description for newly added optional audio codecs.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
On Baseboard Management Controller (BMC) systems it's sometimes
necessary for a LED to retain its state across a BMC reset (which is
independent of the host system state). Add a devicetree property to
describe this behaviour. The property would typically be used in
conjunction with 'default-state = "keep"'.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Brandon Wyman <bjwyman@gmail.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
This adds the devicetree bindings for the PCA955x I2C LED blinkers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Deprecate the legacy Rockchip PCIe PHY and encourage users to use per-lane
PHY mode by setting #phy-cells to 1.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Deprecate legacy PHY model and encourage per-lane PHY model.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Commit b053dc5a72 (powerpc: Refactor device tree binding) split the
Ethernet PHY binding documentation out of the big booting-without-of.txt
file, leaving a dangling reference to "section 2" in the 'interrupts'
property description. Drop that reference, and make the description look
more like the rest.
While at it, make the example interrupt-parent phandle look more like a
real world phandle, and use an IRQ_TYPE_ macro for the 'interrupts'
type.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Rob Herring <robh@kernel.org>
Add DT bindings for the onboard SATA controller present on the MediaTek
SoCs.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Allow for the enablement of MEF and the support for the extended
epoch in SIE and VSIE for the extended guest TOD-Clock.
A new interface is used for getting/setting a guest's extended TOD-Clock
that uses a single ioctl invocation, KVM_S390_VM_TOD_EXT. Since the
host time is a moving target that might see an epoch switch or STP sync
checks we need an atomic ioctl and cannot use the exisiting two
interfaces. The old method of getting and setting the guest TOD-Clock is
still retained and is used when the old ioctls are called.
Signed-off-by: Collin L. Walling <walling@linux.vnet.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.vnet.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Reviewed-by: Jason J. Herne <jjherne@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Add document providing definitions of terms and core explanations
for tag matching (TM) protocols, eager and rendezvous,
TM application header, tag list manipulations and matching process.
Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch adds the binding documentation for Spreadtrum I2C
controller device.
Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Allow a client call that failed on network error to be retried, provided
that the Tx queue still holds DATA packet 1. This allows an operation to
be submitted to another server or another address for the same server
without having to repackage and re-encrypt the data so far processed.
Two new functions are provided:
(1) rxrpc_kernel_check_call() - This is used to find out the completion
state of a call to guess whether it can be retried and whether it
should be retried.
(2) rxrpc_kernel_retry_call() - Disconnect the call from its current
connection, reset the state and submit it as a new client call to a
new address. The new address need not match the previous address.
A call may be retried even if all the data hasn't been loaded into it yet;
a partially constructed will be retained at the same point it was at when
an error condition was detected. msg_data_left() can be used to find out
how much data was packaged before the error occurred.
Signed-off-by: David Howells <dhowells@redhat.com>
Add a callback to rxrpc_kernel_send_data() so that a kernel service can get
a notification that the AF_RXRPC call has transitioned out the Tx phase and
is now waiting for a reply or a final ACK.
This is called from AF_RXRPC with the call state lock held so the
notification is guaranteed to come before any reply is passed back.
Further, modify the AFS filesystem to make use of this so that we don't have
to change the afs_call state before sending the last bit of data.
Signed-off-by: David Howells <dhowells@redhat.com>
The deprecated DT properties are part of the GIT history,
no need to keep them around any longer.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Remove the 32-bit CMT compat strings to reduce maintenance burden.
It should be fine to break DT compatibility because the 32-bit
CMT DT binding was never part of any upstream DTS file.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Add documentation for new separate CMT0 and CMT1 DT compatible strings
for R-Car Gen2. These compat strings allow us to enable CMT1-specific
features in the driver. The old compat strings will be deprecated in
the not so distant future.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Remove the sh7372 CMT compat string to reduce maintenance burden.
It should be fine to break DT compatibility because:
1) The sh7372 SoC support has been removed from upstream
2) The sh7372 CMT DT binding was never part of upstream DTS
3) The CMT driver never matches on the sh7372 binding
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
We add ability for all cores at NPS SoC to control the number of cycles
HW thread can execute before it is replace with another eligible
HW thread within the same core. The replacement is done by the
HW scheduler.
Signed-off-by: Noam Camus <noamca@mellanox.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
[vgupta: simplified handlign of out of range argument value]
The Documentation/power/states.txt document is now redundant and
sonewhat outdated, so delete it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reorganize the power management part of admin-guide by adding a
description of major power management strategies supported by the
kernel (system-wide and working-state power management) to it and
dividing the rest of the material into the system-wide PM and
working-state PM chapters.
On top of that, add a description of system sleep states to the
system-wide PM chapter.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Document the devicetree bindings in 8250.txt for MediaTek BTIF
controller which could be found on MT7622 and MT7623 SoC.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document support for the (H)SCIF serial ports in the Renesas R-Car D3
(r8a77995) SoC.
No driver update is needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver provides PS/2 serio bus support by implementing bit banging
with the GPIO API. The GPIO pins, data and clock, can be configured with
a node in the device tree or by generic device properties (GDP).
Writing to a device is supported as well, though it is possible timings
can not be halt as they are tough and difficult to reach with bit banging.
Therefore it can be configured (also in DT and GDP) whether the serio
write function should be available for clients.
This driver is for development purposes and not recommended for productive
use. However, this driver can be useful e.g. when no USB port is available
or using old peripherals is desired as PS/2 controller chips getting rare.
This driver was tested on bcm2825 and on Kirin 960 and it worked well
together with the atkbd and psmouse driver.
Signed-off-by: Danilo Krummrich <danilokrummrich@dk-develop.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
NVMEM has been in kernel since v4.2 but the ABI document was missing
since then. userspace interface did not change since then and seems
stable, so this patch documents the nvmem ABI.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
Document in the Device Tree binding document that this manufacturer should
be used as the generic fallback. Also document the deprecated vendors.
Suggested-by: Wolfram Sang <wsa@the-dreams.de>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch fixes the below warning
--> Use #include <linux/io.h> instead of <asm/io.h>
--> Use #include <linux/uaccess.h> instead of <asm/uaccess.h>
--> please, no space before tabs
--> Block comments use a trailing */ on a separate line
--> Possible unnecessary 'out of memory' message
--> Block comments use * on subsequent lines
--> Block comments use a trailing */ on a separate line
--> braces {} are not necessary for any arm of this statement
--> DT compatible string "xlnx,opb-hwicap-1.00.b"
appears un-documented
--> DT compatible string "xlnx,xps-hwicap-1.00.a"
appears un-documented
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Detailed description for this pull request:
1. Add new 'extcon-usbc-cros-ec.c' driver
- ChromeOS Embedded Controller extcon driver supports
the detection of the Display Port (EXTCON_DISP_DP)
through USB C-type and contol it.
2. Update extcon core
- Modify the description for both functions and structures
in order to improve the readability and give the more correct
guide about the role of functions because there are different
explanation even if the same arguments.
- Keep the indentation with tab instead of space
- Remove the following deprecated extcon API. The deprecated API
are exchanged on all of linux tree.
: extcon_get_cable_state_() -> extcon_get_state()
: extcon_set_cable_state_() -> extcon_set_state_sync()
3. Include the two immutable branch as following:
- ib-extcon-mfd-4.14 for the 'extcon-ubsc-cros-ec.c' driver
because the patches of 'extcon-ubsc-cros-ec.c' touch the MFD directory.
- ib-extcon-usb-phy-4.14 for removing the deprecated extcon API
because the usb/phy driver usese the deprecated extcon API.
So, this immutable branch alters the extcon API and then
remove them from extcon.
4. Fix minor issue of extcon driver
- Fix the MHL detection on extcon-max77693.c
- Convert to using %pOF instead of full_name on extcon.c
- Add 'const' kerywod for acpi_device_id on extcon-intel-int3496.c
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=oQMu
-----END PGP SIGNATURE-----
Merge tag 'extcon-next-for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into char-misc-next
Chanwoo writes:
Update extcon for 4.14
Detailed description for this pull request:
1. Add new 'extcon-usbc-cros-ec.c' driver
- ChromeOS Embedded Controller extcon driver supports
the detection of the Display Port (EXTCON_DISP_DP)
through USB C-type and contol it.
2. Update extcon core
- Modify the description for both functions and structures
in order to improve the readability and give the more correct
guide about the role of functions because there are different
explanation even if the same arguments.
- Keep the indentation with tab instead of space
- Remove the following deprecated extcon API. The deprecated API
are exchanged on all of linux tree.
: extcon_get_cable_state_() -> extcon_get_state()
: extcon_set_cable_state_() -> extcon_set_state_sync()
3. Include the two immutable branch as following:
- ib-extcon-mfd-4.14 for the 'extcon-ubsc-cros-ec.c' driver
because the patches of 'extcon-ubsc-cros-ec.c' touch the MFD directory.
- ib-extcon-usb-phy-4.14 for removing the deprecated extcon API
because the usb/phy driver usese the deprecated extcon API.
So, this immutable branch alters the extcon API and then
remove them from extcon.
4. Fix minor issue of extcon driver
- Fix the MHL detection on extcon-max77693.c
- Convert to using %pOF instead of full_name on extcon.c
- Add 'const' kerywod for acpi_device_id on extcon-intel-int3496.c
Intel TH:
* Updated subdevice management code to better fit host mode
* Added support for Low Power Path (LPP) output type
* Fixed memory allocation with IOMMU enabled (DMAR tables)
* Added Cannon Lake PCH PCI IDs
* Added a quirk to force time sync on devices that need it
STM:
* Fixed potential read overflow in ioctl()
* Documented stm_ftrace source.
-----BEGIN PGP SIGNATURE-----
iJkEABEIAEEWIQQSviFCoXpKPDNATbnrxfYkYwVX/wUCWaBJXyMcYWxleGFuZGVy
LnNoaXNoa2luQGxpbnV4LmludGVsLmNvbQAKCRDrxfYkYwVX/+4vAP9vSdGYkIzJ
i09a14Oqj1Qv2PWFMTSjYolLHZCgZJ6LqQD/S0CY8eVmHeoYv2U6jHpZFIX7yQsP
ahlAiqgqneV6GE0=
=zU1K
-----END PGP SIGNATURE-----
Merge tag 'stm-for-greg-20170825' of git://git.kernel.org/pub/scm/linux/kernel/git/ash/stm into char-misc-next
Alexander writes:
stm class / intel_th: Updates for 4.14
Intel TH:
* Updated subdevice management code to better fit host mode
* Added support for Low Power Path (LPP) output type
* Fixed memory allocation with IOMMU enabled (DMAR tables)
* Added Cannon Lake PCH PCI IDs
* Added a quirk to force time sync on devices that need it
STM:
* Fixed potential read overflow in ioctl()
* Documented stm_ftrace source.
If secure authentication of a devices fails, either because the device
already has another key uploaded, or there is some other error sending
challenge to the device, and the user only wants to approve the device
just once (without a new key being uploaded to the device) the current
implementation does not allow this because the key cannot be cleared
once set even if we allow it to be changed.
Make this scenario possible and allow clearing the key by writing
empty string to the key sysfs file.
Signed-off-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Linux coresight drivers define the programmable ATB replicator as
Qualcomm replicator, while this is designed by ARM. This can cause
confusion to a user selecting the driver. Cleanup all references to
make it explicitly clear. This patch :
1) Replace the compatible string for the replicator :
qcom,coresight-replicator1x => arm,coresight-dynamic-replicator
2) Changes the Kconfig symbol (since this is not part of any defconfigs)
CORESIGHT_QCOM_REPLICATOR => CORESIGHT_DYNAMIC_REPLICATOR
3) Improves the help message in the Kconfig.
4) Changes the name of the driver and the file :
coresight-replicator-qcom => coresight-dynamic-replicator
Cc: Pratik Patel <pratikp@codeaurora.org>
Cc: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: devicetree@vger.kernel.org
Cc: Mark Rutland <mark.rutland@arm.com>
Acked-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_PPC_MEMTRACE must be set to use this feature. This can only be
used on powernv platforms.
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
[mpe: Update dates and kernel versions, mention size is in bytes]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some of the DMA controllers are capable of issuing the commands
to peripheral by the DMA. These commands can be list of register
reads/writes and its different from normal data reads/writes.
This patch adds new flag DMA_PREP_CMD in DMA API which tells
the driver that the data passed to DMA API is command data
and DMA controller driver will form descriptor in the required
format.
This flag can be used by any DMA controller driver which requires
the descriptor in different format for non-Data descriptors.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add support for the SuperSpeed Link Layer test case TD.7.34
which requires the operator to place the port into compliance
mode, and to subsequently bring it out via reset. Historically
according to the (now deprecated) USB 3.0 specification a
SuperSpeed host downstream port would automatically transition
to Compliance mode from the Polling state if LFPS polling times
out. However the language in USB 3.1 as well as xHCI 1.1 states
it may be required to explicitly enable this transition. For
such hosts this is done by sending a SET_FEATURE(PORT_LINK_STATE)
with the state set to Compliance to the root hub port.
Similar to the other supported commands, to do this via sysfs:
echo > /sys/bus/usb/devices/2-0\:1.0/enable_compliance
According to xHCI 1.1 section 4.19.1.2.4.1, this enables the
transition to compliance mode upon LFPS timeout. Note that this
can only be issued when the port is in disconnected state. And
in order to disable this behavior on subsequent transitions, a
warm reset should be issued. So add another entry to do that:
echo > /sys/bus/usb/devices/2-0\:1.0/warm_reset
In general these attributes can also be useful for other USB
SuperSpeed compliance tests such as electrical and eye diagram
testing which require CPn patterns to be transmitted.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This binding still doesn't please everyone, and we're getting far too
close from the release to allow it to reach a stable version.
Let's remove it until the discussion settles down.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Recently added FE_NONE to the enum fe_status, so update the
documentation accordingly.
[mchehab@s-opensource.com: change description to actually
reflect what FE_NONE means: no lock of any kind]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add MT7622 i2c binding to binding file. Compare to MT8173 i2c
controller, MT7622 limits message numbers to 255, and does not
support 4GB DMA mode.
Signed-off-by: Jun Gao <jun.gao@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use common name MediaTek and modify the compatible information
formats of all SoCs to the same.
Signed-off-by: Jun Gao <jun.gao@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Do some minor editorial changes to make this chapter visually
better, and the example a little bit clearer.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The description of the DVBv5 API was written a long time ago,
where the API was still new, and there were not apps using it.
Now that the API is stable and used by new applications, clarify
that DVBv3 calls should not be used and why.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ATSC 3.0 uses MPEG Media Transport, with is not currently
supported. Yet, we'll need to implement it sooner or later.
So, mention about it at the specs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The description of what SEC means fits well as a footnote.
That makes the need of saying that SEC is only for Satellite
when it was mentioned, as the footnote already says that.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The introduction for the frontend chapter is not quite
correct:
- it tells that it supports only three types of
delivery systems, in opposite to three *groups*;
- It adds ISDB-C to the list of supported systems,
but, this is not true.
Fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The device numbering for DVB uses "M" and "N" as vars for the
number of the device, but sometimes this is printed using normal
font instead of verbatim.
While here, remove an extra space after quotation marks.
This is a minor cleanup with no changes at the text.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some CSI-2 transmitters will finish an ongoing frame whereas others will
not. Document that receiver drivers should not assume a particular
behaviour but to work in both cases.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Document DT bindings for Analog Devices as3645a flash LED controller which
also supports an indicator LED.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Sphinx 1.6 generates some LaTeX code before each table,
starting its own environment before calling tabulary,
apparently to improve table layout.
The problem is that such environment is incompatible with
adjustbox. While, in thesis, it should be possible to override
it or to redefine tabulary, I was unable to produce such patch.
Also, that would likely break on some future Sphinx version.
So, instead, let's just change the font size on bigger tables,
in order for them to fit into the page size. That is not as
good as adjustbox, and require some manual work, but it should
be less sensitive to Sphinx changes.
While here, adjust a few other tables whose text is exceeding
the cell boundaries.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently there are no ->swap_{in,out} method in address_space_operations
sructure definition, so the statement that anything is going to be proxied
through them is wrong.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Now that the PDF building issues with Sphinx 1.6 got fixed,
update the documentation and scripts accordingly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
On Sphinx 1.6, fancy boxes are used for verbatim. The sphinx.sty
sets verbatim font is always \small. That causes a problem
inside tables that use smaller fonts, as it can be too big for
the box.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Update the Qualcomm Camera Subsystem driver document with a media
controller pipeline graph diagram.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Update Qualcomm Camera Subsystem driver document for the PIX interface
and format conversion support.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These formats are compressed 12-bit raw bayer formats with four different
pixel orders. They are similar to 10-bit variants. The formats added by
this patch are
V4L2_PIX_FMT_SBGGR12P
V4L2_PIX_FMT_SGBRG12P
V4L2_PIX_FMT_SGRBG12P
V4L2_PIX_FMT_SRGGB12P
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Dongwoon DW9714 is a voice coil lens driver.
Also add a vendor prefix for Dongwoon for one did not exist previously.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Command line options allow us to ignore features that we don't want.
Also we can re-enable options that have been disabled on a platform
(so long as the underlying h/w actually supports the option).
[ tglx: Marked the option array __initdata and the helper function __init ]
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Fenghua" <fenghua.yu@intel.com>
Cc: Ravi V" <ravi.v.shankar@intel.com>
Cc: "Peter Zijlstra" <peterz@infradead.org>
Cc: "Stephane Eranian" <eranian@google.com>
Cc: "Andi Kleen" <ak@linux.intel.com>
Cc: "David Carrillo-Cisneros" <davidcc@google.com>
Cc: Vikas Shivappa <vikas.shivappa@linux.intel.com>
Link: http://lkml.kernel.org/r/0c37b0d4dbc30977a3c1cee08b66420f83662694.1503512900.git.tony.luck@intel.com
This patch adds a description to the stm_ftrace device source, an
interface for collecting Ftrace's function trace information via
STM devices.
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Julia reported that the document looked unfinished, and it is. I
forgot to include the example cooked up by Paul here:
https://lkml.kernel.org/r/20170731174345.GL3730@linux.vnet.ibm.com
and I added an explicit example showing how, while it is an ACQUIRE
pattern, it really does provide an MB.
Reported-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Since i80/command mode is determined in runtime by propagating info
from panel this property can be removed.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The hpsa driver now has support for all boards the cciss driver
used to support, so this patch removes the cciss driver and
make hpsa an alias to cciss.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reflecting IPv6 Flow Label at server nodes is useful in environments
that employ multipath routing to load balance the requests. As "IPv6
Flow Label Reflection" standard draft [1] points out - ICMPv6 PTB error
messages generated in response to a downstream packets from the server
can be routed by a load balancer back to the original server without
looking at transport headers, if the server applies the flow label
reflection. This enables the Path MTU Discovery past the ECMP router in
load-balance or anycast environments where each server node is reachable
by only one path.
Introduce a sysctl to enable flow label reflection per net namespace for
all newly created sockets. Same could be earlier achieved only per
socket by setting the IPV6_FL_F_REFLECT flag for the IPV6_FLOWLABEL_MGR
socket option.
[1] https://tools.ietf.org/html/draft-wang-6man-flow-label-reflection-01
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the necessary data for handling io voltage domains on the RV1108.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
git.kernel.org links don't work (fatal: repository ... not found).
Update them with the current style from https://git.kernel.org
There is no HTTP option, so also switch HTTP -> HTTPS.
Signed-off-by: Andrii Bordunov <andrew.bordunov@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The rtmutex remove a pending owner bit in in rt_mutex::owner, in
commit 8161239a8b ("rtmutex: Simplify PI algorithm and make highest prio task get lock")
But the document was changed accordingly. Updating it to a meaningful
state.
BTW, as 'Steven Rostedt' mentioned:
There is still technically a "Pending Owner", it's just not called
that anymore. The pending owner happens to be the top_waiter of a lock
that has no owner and has been woken up to grab the lock.
Signed-off-by: Alex Shi <alex.shi@linaro.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Juri Lelli <juri.lelli@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
To: linux-doc@vger.kernel.org
To: linux-kernel@vger.kernel.org
To: Jonathan Corbet <corbet@lwn.net>
To: Ingo Molnar <mingo@redhat.com>
To: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The rt-mutex-design documents didn't gotten meaningful update from its
first version. Even after owner's pending bit was removed in commit 8161239a8b
("rtmutex: Simplify PI algorithm and make highest prio task get lock")
and priority list 'plist' changed to rbtree. And Peter Zijlstra did some
clean up and fix for deadline task changes on tip tree.
So update it to latest code and make it meaningful.
Steven Rostedt and Sebastian Siewior gave much of comments and input
in this doc. Thanks!
Signed-off-by: Alex Shi <alex.shi@linaro.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Juri Lelli <juri.lelli@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
To: linux-doc@vger.kernel.org
To: linux-kernel@vger.kernel.org
To: Jonathan Corbet <corbet@lwn.net>
To: Ingo Molnar <mingo@redhat.com>
To: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
according to what Documentation/doc-guide/sphinx.rst says::
The ReST markups currently used by the Documentation/ files
are meant to be built with ``Sphinx`` version 1.3 or upper.
Signed-off-by: Markus Heiser <markus.heiser@darmarit.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This is a minor patch that fixes the following typo in the NVMEM documentation:
When a consumers no longer needs the NVMEM
to,
When a consumer no longer needs the NVMEM
Signed-off-by: Narendran Sankaran <naren.kernel@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Currently, on Sphinx up to version 1.4, pdf output uses a vertical
margin of 1 inch. For upper versions, it uses a margin of 0.5 inches.
That causes both page headers and footers to be very close to the margin
of the sheet. Not all printers support writing like that.
Also, there's no reason why the layout for newer versions would be
different than for previous ones.
So, standardize it, by always setting to 1 inch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Right now, if the building system doesn't find Sphinx, it
bails out, without providing any instructions about what
should be done.
Instead, run a script, providing some guidance about the
steps needed for Sphinx build to work.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Several paths in the security/keys documentation were incorrect.
Signed-off-by: Josh Holland <anowlcalledjosh@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Add support to the keystone remoteproc driver for managing the
DSP present in the Keystone 2 66AK2G SoC. The 66AK2G SoC has
a Power Management Micro Controller (PMMC) that manages the
individual device's power, clock and reset functionalities.
The keystone remoteproc driver already uses standard frameworks
for reset and clock control, so it doesn't require any significant
modifications other than a new compatible suitable for 66AK2G DSP.
The binding document is also updated to reflect the modified
property values used by the 66AK2G DSP node as compared to the
values used by existing Keystone 2 DSPs.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the device tree bindings document for the DSP processor
subsystem devices on TI Davinci DA8xx/OMAP-L13x SoCs.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add support for the IPQ8074 PCIe controller. IPQ8074 supports Gen 1/2, one
lane, two PCIe root complex with support for MSI and legacy interrupts, and
it conforms to PCI Express Base 2.1 specification.
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Sapphire som+baseboard which is another evaluation board for Rocckhip
customers and the rk3399-based som+baseboard from Austria-based
Theobroma Systems, which interestingly is in a miniITX formfactor
and provides a real PCIe x4 slot.
New nodes include on rk3399 graphics (vops, hdmi, etc) and more iommus,
on rk3328 iommus, pwm, thermal management, and sound as well as operating
points and rk3368 got iommu nodes and cpu operating points.
On existing boards firefly got operating points, the rk3328-evb got its
pmic and gru boards got some sound-related fixes.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlmdnagQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgSpBB/9v6flM/QtBVeXhR1tfrXIt3veUaiwiTwhg
PIj6J7EJZCgA9TiHr4zcQzjCx581a9v1rUEpnhZyi7d/zrNurpJRYtBNcqfDS28Z
kyL30gwf/y4nVAzgIODGMNRWe3+IETNCIRZ236cV7jr9HgKmHvA0qc2aMzjHPMCF
XS9wPXgEW1kYIgKqzq1drAWY3iVB0W37KMX9HKVQfAlPcGu5jobk0lruQBZV0InH
8NR3NB9a7eknzPejmBO2ga0idS0oAc/eFQ8h2bHrxWVm1JO+2QDc7epxWCTmxBcP
DLy+7tuQiXEFc25AM3QpW97pJuqDT+zeZXd/F5BK5uGnpH63SNbi
=D65g
-----END PGP SIGNATURE-----
Merge tag 'v4.14-rockchip-dts64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt64
Pull "second round of Rockchip dts64 changes for 4.14" from Heiko Stübner:
3 new boards, the rk3328-based Rock64 from the Pine64-makers, the
Sapphire som+baseboard which is another evaluation board for Rocckhip
customers and the rk3399-based som+baseboard from Austria-based
Theobroma Systems, which interestingly is in a miniITX formfactor
and provides a real PCIe x4 slot.
New nodes include on rk3399 graphics (vops, hdmi, etc) and more iommus,
on rk3328 iommus, pwm, thermal management, and sound as well as operating
points and rk3368 got iommu nodes and cpu operating points.
On existing boards firefly got operating points, the rk3328-evb got its
pmic and gru boards got some sound-related fixes.
* tag 'v4.14-rockchip-dts64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (29 commits)
arm64: dts: rockchip: add Haikou baseboard with RK3399-Q7 SoM
arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM
dt-bindings: add rk3399-q7 SoM
arm64: dts: rockchip: add rk3328-rock64 board
arm64: dts: rockchip: add rk3328 pdm node
arm64: dts: rockchip: add more rk3399 iommu nodes
arm64: dts: rockchip: add rk3368 iommu nodes
arm64: dts: rockchip: add rk3328 iommu nodes
arm64: dts: rockchip: Add basic cpu frequencies for RK3368
arm64: dts: rockchip: add rk805 node for rk3328-evb
arm64: dts: rockchip: Assign mic irq to correct device for Gru
arm64: dts: rockchip: init rk3399 vop clock rates
arm64: dts: rockchip: Add pwm nodes for rk3328
arm64: dts: rockchip: Fix wrong rt5514 dmic delay property for Gru
arm64: dts: rockchip: disable tx ipgap linecheck for rk3399 dwc3
arm64: dts: rockchip: remove num-slots property from rk3399-sapphire
arm64: dts: rockchip: Enable tsadc module on RK3328 eavluation board
arm64: dts: rockchip: add thermal nodes for rk3328 SoC
arm64: dts: rockchip: add tsadc node for rk3328 SoC
arm64: dts: rockchip: add rk3328 i2s nodes
...
(usb, operating points, spi, pwm, adc, watchdog, i2c and devices for
its evb).
RK3228/3229 gets iommu and spi nodes. Similar to the rk3288 which
also gets some more iommu nodes as well as getting converted to 64
bit addresses due to wanting to address more than 4GB of memory
via LPAE.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlmdoA4QHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgeBtB/9oM4MmVRJ0YX7hk4NuU9c4HHdvCW0f1rJe
Q6rE6dP7fW3J27d6PuySVWzvIBmD+3xVA2t0dDm85DIP8f1DFz3vyNhkEsu1VG89
MULTektihczugCy+sh3iHILs4fLXJ8QUjCKJWOcWmZHOaXNXXjJIVjC97m5F4ZAj
KVOYXNnCKdaHYIeP0lkjStL8Z9Ua7svkjfgsSPTGTSJQQ+bGcd/8JnmlkzjfHWLw
qNz6M7FPoJ1rAffskr1At27oRs7UAVSKNAejl8DWKvLXml6NQPRRRu99sLLanxII
3b6LsC6Vwea4a1Rjwx0LZWdDUtB1W34/ZIEw4JceK/i6HfV5K2Oi
=di6U
-----END PGP SIGNATURE-----
Merge tag 'v4.14-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Pull "second round of Rockchip dts32 changes for 4.14" from Heiko Stübner:
A lot of attention for the rv1108 soc targetted at media-processing
(usb, operating points, spi, pwm, adc, watchdog, i2c and devices for
its evb).
RK3228/3229 gets iommu and spi nodes. Similar to the rk3288 which
also gets some more iommu nodes as well as getting converted to 64
bit addresses due to wanting to address more than 4GB of memory
via LPAE.
* tag 'v4.14-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: enable usb for rv1108-evb
ARM: dts: rockchip: add usb nodes for rv1108 SoCs
dt-bindings: update grf-binding for rv1108 SoCs
ARM: dts: rockchip: add cpu power supply for rv1108 evb
ARM: dts: rockchip: add cpu opp table for rv1108
ARM: dts: rockchip: add rk322x iommu nodes
ARM: dts: rockchip: add accelerometer bma250e dt node for rv1108 evb
ARM: dts: rockchip: add pmic rk805 dt node for rv1108 evb
ARM: dts: rockchip: add pwm backlight for rv1108 evb
ARM: dts: rockchip: add pwm dt nodes for rv1108
ARM: dts: rockchip: add spi dt node for rv1108
ARM: dts: rockchip: add saradc support for rv1108
ARM: dts: rockchip: add watchdog dt node for rv1108
ARM: dts: rockchip: add i2c dt nodes for rv1108
clk: rockchip: fix up indentation of some RV1108 clock-ids
clk: rockchip: rename the clk id for HCLK_I2S1_2CH
clk: rockchip: add more clk ids for rv1108
ARM: dts: rockchip: add more iommu nodes on rk3288
ARM: dts: rockchip: convert rk3288 device tree files to 64 bits
ARM: dts: rockchip: add spi node and spi pinctrl on rk3228/rk3229
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Allwinner A10 is now driven by sunxi-ng CCU driver.
Add devicetree binding for it.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner A20 is now driven by sunxi-ng CCU driver.
Add devicetree binding for it.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
- Expression parser enhancements for metrics (Andi Kleen)
- Fix buffer overflow while freeing events in 'perf stat' (Andi Kleen)
- Fix static linking with elfutils's libdf and with libunwind
in Debian/Ubuntu (Konstantin Khlebnikov)
- Tighten detection of BPF events, avoiding matching some other PMU
events such as 'cpu/uops_executed.core,cmask=1/' as a .c source
file that ended up being considered a BPF event (Andi Kleen)
- Add Skylake server uncore JSON vendor events (Andi Kleen)
- Add support for printing new mem_info encodings, including
'perf test' checks (Andi Kleen)
- Really install manpages via 'make install-man' (Konstantin Khlebnikov)
- Fix documentation for perf_event_paranoid and perf_event_mlock_kb
sysctls (Konstantin Khlebnikov)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----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=FjP/
-----END PGP SIGNATURE-----
Merge tag 'perf-core-for-mingo-4.14-20170823' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
- Expression parser enhancements for metrics (Andi Kleen)
- Fix buffer overflow while freeing events in 'perf stat' (Andi Kleen)
- Fix static linking with elfutils's libdf and with libunwind
in Debian/Ubuntu (Konstantin Khlebnikov)
- Tighten detection of BPF events, avoiding matching some other PMU
events such as 'cpu/uops_executed.core,cmask=1/' as a .c source
file that ended up being considered a BPF event (Andi Kleen)
- Add Skylake server uncore JSON vendor events (Andi Kleen)
- Add support for printing new mem_info encodings, including
'perf test' checks (Andi Kleen)
- Really install manpages via 'make install-man' (Konstantin Khlebnikov)
- Fix documentation for perf_event_paranoid and perf_event_mlock_kb
sysctls (Konstantin Khlebnikov)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This commit adds the base Device Tree files for the Armada 8KPlus.
The Armada 8KP SoCs include several hardware blocks, and this
commit only adds support for the AP810 block, that contains the CPU
core and basic peripherals.
AP810 is a high-performance die, includes octal core application
processor based ARMv8-A architecture, two standard high speed DDR4
interface, and GIC-600 interrupt controller.
AP810 Built as part of Marvell’s MoChi AP family products.
Armada-8080 (8KPlus family), include an AP810 block that contains
the CPU core and basic peripherals.
This commit creates the following hierarchy:
* armada-ap810-ap0.dtsi - definitions common to AP810
* armada-ap810-ap0-octa-core.dtsi - description of the octa cores
* armada-8080.dtsi - description of the 8080 SoC
* armada-8080-db.dts - description of the 8080 board
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
As eBPF JIT support for arm32 was added recently with
commit 39c13c204b, it seems appropriate to
add arm32 as arch with support for eBPF JIT in bpf and sysctl docs as well.
Signed-off-by: Shubham Bansal <illusionist.neo@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add more module clocks for R-Car V2H and M3-W,
- Add support for the R-Car Gen3 USB 2.0 clock selector PHY,
- Add support for the new R-Car D3 SoC,
- Allow compile-testing of all (sub)drivers now all dummy infrastructure
is available,
- Small fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=77l6
-----END PGP SIGNATURE-----
Merge tag 'clk-renesas-for-v4.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into clk-next
Pull Renesas clk driver updates from Geert Uytterhoeven:
* Add more module clocks for R-Car V2H and M3-W,
* Add support for the R-Car Gen3 USB 2.0 clock selector PHY,
* Add support for the new R-Car D3 SoC,
* Allow compile-testing of all (sub)drivers now all dummy infrastructure
is available,
* Small fixes and cleanups.
* tag 'clk-renesas-for-v4.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers:
clk: renesas: r8a7796: Add USB3.0 clock
clk: renesas: rcar-usb2-clock-sel: Add R-Car USB 2.0 clock selector PHY
clk: renesas: cpg-mssr: Add R8A77995 support
clk: renesas: rcar-gen3: Add support for SCCG/Clean peripheral clocks
clk: renesas: rcar-gen3: Add divider support for PLL1 and PLL3
clk: renesas: Add r8a77995 CPG Core Clock Definitions
clk: renesas: rcar-gen3-cpg: Refactor checks for accessing the div table
clk: renesas: rcar-gen3-cpg: Drop superfluous variable
clk: renesas: Allow compile-testing of all (sub)drivers
clk: renesas: r8a7792: Add IMR-LX3/LSX3 clocks
clk: renesas: div6: Document fields used for parent selection
Rockchip socs experience with the default approximation. For that we
introduce the ability to override it with a clock-specific approximation
and use that to create the needed rate settings as described in the
Rockchip soc manuals (same for all Rockchip socs).
Apart from that we have support for the rk3126 clock controller
which is similar to the rk3128 with some minimal differences
and a lot of improvements and fixes for the rv1108 clock controller
(missing clocks, some clock-ids, naming fixes, register fixes).
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlmcl8sQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgeiBB/wIf5LHDu09HuOb1bjtYASMc//ve2ymhpd7
QsccJ0nteJTWnYQlrJUPYN8YhRVqPNrz7Fq8PkMMkzm89fQQ6lr5DxOy6olKTPM4
sGf+242eE3XttHjJxcshNPS98A56zBa9OgNC9sUsTex8r7NaJn+Gvlf0sXEgQRQi
5FprJf49/4rlHZypVMg1j+aMEWM8ZAmXLP3F77Qch+rfxE74POV9/HI7EEoSQ9MX
TxwEewmM8IGXY9aVTvtADPmX31CgdOD3qm4giwGkBf2F8SajP8R63wi+BYpNfUTX
+TrexLXEfeKEVtU+xPXsNYmEnAOW6sRvfyUnq4oA1hVSnFoexFA1
=Upwy
-----END PGP SIGNATURE-----
Merge tag 'v4.14-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-next
Pull Rockchip clk driver updates from Heiko Stuebner:
The biggest change is fixing the jitter on the fractional clock-type
Rockchip socs experience with the default approximation. For that we
introduce the ability to override it with a clock-specific approximation
and use that to create the needed rate settings as described in the
Rockchip soc manuals (same for all Rockchip socs).
Apart from that we have support for the rk3126 clock controller
which is similar to the rk3128 with some minimal differences
and a lot of improvements and fixes for the rv1108 clock controller
(missing clocks, some clock-ids, naming fixes, register fixes).
* tag 'v4.14-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
clk: rockchip: fix the rv1108 clk_mac sel register description
clk: rockchip: rename rv1108 macphy clock to mac
clk: rockchip: add rv1108 ACLK_GMAC and PCLK_GMAC clocks
clk: rockchip: add rk3228 SCLK_SDIO_SRC clk id
clk: rockchip: add rv1108 ACLK_GAMC and PCLK_GMAC ID
clk: rockchip: add rk3228 sclk_sdio_src ID
clk: rockchip: add special approximation to fix up fractional clk's jitter
clk: fractional-divider: allow overriding of approximation
clk: rockchip: modify rk3128 clk driver to also support rk3126
dt-bindings: add documentation for rk3126 clock
clk: rockchip: add some critical clocks for rv1108 SoC
clk: rockchip: rename some of clks for rv1108 SoC
clk: rockchip: fix up some clks describe error for rv1108 SoC
clk: rockchip: support more clks for rv1108
clk: rockchip: fix up the pll clks error for rv1108 SoC
clk: rockchip: support more rates for rv1108 cpuclk
clk: rockchip: fix up indentation of some RV1108 clock-ids
clk: rockchip: rename the clk id for HCLK_I2S1_2CH
clk: rockchip: add more clk ids for rv1108
Usual improvements:
- Added support for fixed post-divider on divider and NKM-style clocks
- Added driver for R40 CCU
Non critical fixes (from round 1):
- Fix sunxi-ng/ccu-sunxi-r.h header file guard macro typo
- Make fractional clock modes really used and correctly configured
- Make H3 cpu clock rate change correctly to be used with cpufreq
-----BEGIN PGP SIGNATURE-----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=DKSp
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clk-for-4.14-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into clk-next
Pull Allwinner clock changes from Chen-Yu Tsai:
* Added support for fixed post-divider on divider and NKM-style clocks
* Added driver for R40 CCU
* Fix sunxi-ng/ccu-sunxi-r.h header file guard macro typo
* Make fractional clock modes really used and correctly configured
* Make H3 cpu clock rate change correctly to be used with cpufreq
* tag 'sunxi-clk-for-4.14-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
clk: sunxi-ng: support R40 SoC
dt-bindings: add compatible string for Allwinner R40 CCU
clk: sunxi-ng: nkm: add support for fixed post-divider
clk: sunxi-ng: div: Add support for fixed post-divider
dt-bindings: clock: sunxi-ccu: Add compatibles for sun5i CCU driver
clk: sunxi-ng: allow set parent clock (PLL_CPUX) for CPUX clock on H3
clk: sunxi-ng: h3: gate then ungate PLL CPU clk after rate change
clk: sunxi-ng: Wait for lock when using fractional mode
clk: sunxi-ng: Make fractional helper less chatty
clk: sunxi-ng: multiplier: Fix fractional mode
clk: sunxi-ng: Fix fractional mode for N-M clocks
clk: sunxi-ng: Fix header guard of ccu-sun8i-r.h
1. Qualcom IPQ4019 SoC uses QPIC NAND controller version 1.4.0
which uses BAM DMA Engine while IPQ806x uses EBI2 NAND
which uses ADM DMA Engine.
2. QPIC NAND will 3 BAM channels: command, data tx and data rx
while EBI2 NAND uses only single ADM channel.
3. CRCI is only required for ADM DMA and its not required for
BAM DMA.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
1. Correct the compatible string for IPQ806x
2. Change the NAND controller and NAND chip nodes name
for more clarity.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Currently the compatible “qcom,nandcs” is being used for each
connected NAND device to support for multiple NAND devices in the
same bus. The same thing can be achieved by looking reg property
for each sub nodes which contains the chip select number so this
patch removes the use of “qcom,nandcs” for specifying NAND device
sub nodes.
Since there is no user for this driver currently in so
changing compatible string is safe.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
UniPhier SoCs contain AIDET (ARM Interrupt Detector). This is intended
to provide additional features that are not covered by GIC. The main
purpose is to provide logic inverter to support low level and falling
edge trigger types for interrupt lines from on-board devices.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
RK3399-Q7 is a Qseven compatible system-on-module by Theobroma Systems.
This adds the module and the EVK baseboard "Haikou"
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds the compatible of GRF and USBGRF for RV1108 SoCs.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
TI AMC6821 fan controller and Intersil ISL1208 are trivial
devices, so add them to the binding list.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Theobroma Systems is a design house specialized in embedded systems
and a manufacturer of system-on-modules.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The ROCK64 is a credit card size 4K60P HDR Media Board Computer using the
Rockchip RK3328 Quad-Core ARM Cortex A53 64-Bit Processor and supporting
up to 4GB 1600MHz LPDDR3 memory. It provides eMMC module socket, MicroSD
Card slot, Pi-2 Bus, Pi-P5+ Bus, USB 3.0 and many others peripheral
devices interface for makers to integrate with sensors and devices.
The devicetree currently supports basic peripherals, with more to be
added later on.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch documents the new marvell,system-controller property used by
the Marvell ppv2 network driver.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update Documentation/networking/netvsc.txt for UDP hash level setting
and related info.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
*) Add USB PHY driver for Ralink SoC
*) Make phy-mt65xx-usb3 driver support PCIe and SATA phy
*) Add mediatek directory and rename phy-mt65xx-usb3 to phy-mtk-tphy.c
since it now supports USB3.0, PCIe and SATA PHYs
*) Make sun4i-usb-phy driver support USB PHYs for A83T SoC
*) Make phy-qcom-qmp driver support USB PHYs for IPQ8074 SoC
*) Make rockchip-inno-usb2 driver support usb2-phy for rv1108 SoC
*) Minor fixes in phy drivers
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=SckR
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.14_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.14
*) Add USB PHY driver for Ralink SoC
*) Make phy-mt65xx-usb3 driver support PCIe and SATA phy
*) Add mediatek directory and rename phy-mt65xx-usb3 to phy-mtk-tphy.c
since it now supports USB3.0, PCIe and SATA PHYs
*) Make sun4i-usb-phy driver support USB PHYs for A83T SoC
*) Make phy-qcom-qmp driver support USB PHYs for IPQ8074 SoC
*) Make rockchip-inno-usb2 driver support usb2-phy for rv1108 SoC
*) Minor fixes in phy drivers
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Not a big pull request this time around. Only 49 non-merge
commits. This pull request is, however, all over the place. Most of
the changes are in the bdc driver adding support for USB Phy layer and
PM.
Renesas adds support for R-Car H3 ES2.0 and R-Car M3-W SoCs.
Also here is PM_RUNTIME support for dwc3-keystone.
UDC Core got a DMA unmap fix to make sure we only unmap requests that
were, indeed, mapped.
Other than these, we have a lot of cleanups, many of them adding
'const' to several places.
-----BEGIN PGP SIGNATURE-----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=FSil
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.14 merge window
Not a big pull request this time around. Only 49 non-merge
commits. This pull request is, however, all over the place. Most of
the changes are in the bdc driver adding support for USB Phy layer and
PM.
Renesas adds support for R-Car H3 ES2.0 and R-Car M3-W SoCs.
Also here is PM_RUNTIME support for dwc3-keystone.
UDC Core got a DMA unmap fix to make sure we only unmap requests that
were, indeed, mapped.
Other than these, we have a lot of cleanups, many of them adding
'const' to several places.
Initialize hw interface as part of the nic initialization for accessing hw.
Signed-off-by: Aviad Krawczyk <aviad.krawczyk@huawei.com>
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It only supports rmii interface. Add constants and callback functions
for the dwmac on rv1108 socs. As can be seen, the base structure is
the same, only registers and the bits in them moved slightly.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix misprint CAP_IOC_LOCK -> CAP_IPC_LOCK. This capability have nothing
to do with raw tracepoints. This part is about bypassing mlock limits.
Sysctl kernel.perf_event_paranoid = -1 allows raw and ftrace function
tracepoints without CAP_SYS_ADMIN.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/150322916080.129746.11285255474738558340.stgit@buzz
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Renesas RZ/G1E (R8A7745) SoC GPIO blocks are identical to the R-Car Gen2
family. Add support for its GPIO controllers.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Propagate errors on group config, now r8a7740-armadillo800eva.dts is
fixed,
- Add MSIOF and USB2.0 pin groups on R-Car H3 ES2.0,
- Add USB2.0 and USB3.0 pin groups on R-Car M3-W,
- Add a missing MMC pin group on R-Car M2-W and RZ/G1M,
- Add initial support for R-Car D3,
- Small fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xgLM
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.14
- Propagate errors on group config, now r8a7740-armadillo800eva.dts is
fixed,
- Add MSIOF and USB2.0 pin groups on R-Car H3 ES2.0,
- Add USB2.0 and USB3.0 pin groups on R-Car M3-W,
- Add a missing MMC pin group on R-Car M2-W and RZ/G1M,
- Add initial support for R-Car D3,
- Small fixes and cleanups.
Document the device tree bindings for the ARTPEC crypto accelerator on
ARTPEC-6 and ARTPEC-7 SoCs.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This adds support usb2-phy for rv1108 SoCs and amend phy Documentation.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add otg-mux property to support multiplexed interrupt in otg-port
on some Rockchip SoC (e.g RV1108).
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add rockchip,usbgrf property to support the registers of usb-phy
that are distributed in grf and usbgrf on some special Rockchip
SoCs (e.g RV1108).
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The A83T has 3 USB PHYs, 1 for OTG, 1 for standard USB, 1 for USB HSIC.
Add a compatible string for it, and describe the needed properties.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The Allwinner H3 SoC has 4 USB PHYs, so it needs four sets of pmu
regions, clocks, resets, and optional vbus properties. These were
not described when the H3 compatible string was added.
Fixes: 626a630e00 ("phy-sun4i-usb: Add support for the host usb-phys
found on the H3 SoC")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Linus Torvalds