Adds an optional call to sock_ops BPF program based on whether the
BPF_SOCK_OPS_RTO_CB_FLAG is set in bpf_sock_ops_flags.
The BPF program is passed 2 arguments: icsk_retransmits and whether the
RTO has expired.
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
When a tcp socket is closed, if it detects that its net namespace is
exiting, close immediately and do not wait for FIN sequence.
For normal sockets, a reference is taken to their net namespace, so it will
never exit while the socket is open. However, kernel sockets do not take a
reference to their net namespace, so it may begin exiting while the kernel
socket is still open. In this case if the kernel socket is a tcp socket,
it will stay open trying to complete its close sequence. The sock's dst(s)
hold a reference to their interface, which are all transferred to the
namespace's loopback interface when the real interfaces are taken down.
When the namespace tries to take down its loopback interface, it hangs
waiting for all references to the loopback interface to release, which
results in messages like:
unregister_netdevice: waiting for lo to become free. Usage count = 1
These messages continue until the socket finally times out and closes.
Since the net namespace cleanup holds the net_mutex while calling its
registered pernet callbacks, any new net namespace initialization is
blocked until the current net namespace finishes exiting.
After this change, the tcp socket notices the exiting net namespace, and
closes immediately, releasing its dst(s) and their reference to the
loopback interface, which lets the net namespace continue exiting.
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1711407
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=97811
Signed-off-by: Dan Streetman <ddstreet@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three sets of overlapping changes, two in the packet scheduler
and one in the meson-gxl PHY driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the retransmit timer currently refreshes tcp_mstamp
We should do the same for delayed acks and keepalives.
Even if RFC 7323 does not request it, this is consistent to what linux
did in the past, when TS values were based on jiffies.
Fixes: 385e20706f ("tcp: use tp->tcp_mstamp in output path")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Mike Maloney <maloney@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Mike Maloney <maloney@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this patch, active Fast Open is paused on a specific
destination IP address if the previous connections to the
IP address have experienced recurring timeouts . But recent
experiments by Microsoft (https://goo.gl/cykmn7) and Mozilla
browsers indicate the isssue is often caused by broken middle-boxes
sitting close to the client. Therefore it is much better user
experience if Fast Open is disabled out-right globally to avoid
experiencing further timeouts on connections toward other
destinations.
This patch changes the destination-IP disablement to global
disablement if a connection experiencing recurring timeouts
or aborts due to timeout. Repeated incidents would still
exponentially increase the pause time, starting from an hour.
This is extremely conservative but an unfortunate compromise to
minimize bad experience due to broken middle-boxes.
Reported-by: Dragana Damjanovic <ddamjanovic@mozilla.com>
Reported-by: Patrick McManus <mcmanus@ducksong.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Wei Wang <weiwan@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce one indentation level to make code more readable.
tcp_sync_mss() can be factorized.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Note that sysctl_tcp_thin_dupack was not used, I deleted it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: netdev@vger.kernel.org
Cc: dccp@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a linear list to store all skbs in write queue has been okay
for quite a while : O(N) is not too bad when N < 500.
Things get messy when N is the order of 100,000 : Modern TCP stacks
want 10Gbit+ of throughput even with 200 ms RTT flows.
40 ns per cache line miss means a full scan can use 4 ms,
blowing away CPU caches.
SACK processing often can use various hints to avoid parsing
whole retransmit queue. But with high packet losses and/or high
reordering, hints no longer work.
Sender has to process thousands of unfriendly SACK, accumulating
a huge socket backlog, burning a cpu and massively dropping packets.
Using an rb-tree for retransmit queue has been avoided for years
because it added complexity and overhead, but now is the time
to be more resistant and say no to quadratic behavior.
1) RTX queue is no longer part of the write queue : already sent skbs
are stored in one rb-tree.
2) Since reaching the head of write queue no longer needs
sk->sk_send_head, we added an union of sk_send_head and tcp_rtx_queue
Tested:
On receiver :
netem on ingress : delay 150ms 200us loss 1
GRO disabled to force stress and SACK storms.
for f in `seq 1 10`
do
./netperf -H lpaa6 -l30 -- -K bbr -o THROUGHPUT|tail -1
done | awk '{print $0} {sum += $0} END {printf "%7u\n",sum}'
Before patch :
323.87
351.48
339.59
338.62
306.72
204.07
304.93
291.88
202.47
176.88
2840
After patch:
1700.83
2207.98
2070.17
1544.26
2114.76
2124.89
1693.14
1080.91
2216.82
1299.94
18053
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP offload conflict is dealt with by simply taking what is
in net-next where we have removed all of the UFO handling code
entirely.
The TCP conflict was a case of local variables in a function
being removed from both net and net-next.
In netvsc we had an assignment right next to where a missing
set of u64 stats sync object inits were added.
Signed-off-by: David S. Miller <davem@davemloft.net>
prequeue is a tcp receive optimization that moves part of rx processing
from bh to process context.
This only works if the socket being processed belongs to a process that
is blocked in recv on that socket.
In practice, this doesn't happen anymore that often because nowadays
servers tend to use an event driven (epoll) model.
Even normal client applications (web browsers) commonly use many tcp
connections in parallel.
This has measureable impact only in netperf (which uses plain recv and
thus allows prequeue use) from host to locally running vm (~4%), however,
there were no changes when using netperf between two physical hosts with
ixgbe interfaces.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the mentioned commit, some of our packetdrill tests became flaky.
TCP_SYNCNT socket option can limit the number of SYN retransmits.
retransmits_timed_out() has to compare times computations based on
local_clock() while timers are based on jiffies. With NTP adjustments
and roundings we can observe 999 ms delay for 1000 ms timers.
We end up sending one extra SYN packet.
Gimmick added in commit 6fa12c8503 ("Revert Backoff [v3]: Calculate
TCP's connection close threshold as a time value") makes no
real sense for TCP_SYN_SENT sockets where no RTO backoff can happen at
all.
Lets use a simpler logic for TCP_SYN_SENT sockets and remove @syn_set
parameter from retransmits_timed_out()
Fixes: 9a568de481 ("tcp: switch TCP TS option (RFC 7323) to 1ms clock")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP_USER_TIMEOUT is still converted to jiffies value in
icsk_user_timeout
So we need to make a conversion for the cases HZ != 1000
Fixes: 9a568de481 ("tcp: switch TCP TS option (RFC 7323) to 1ms clock")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP Timestamps option is defined in RFC 7323
Traditionally on linux, it has been tied to the internal
'jiffies' variable, because it had been a cheap and good enough
generator.
For TCP flows on the Internet, 1 ms resolution would be much better
than 4ms or 10ms (HZ=250 or HZ=100 respectively)
For TCP flows in the DC, Google has used usec resolution for more
than two years with great success [1]
Receive size autotuning (DRS) is indeed more precise and converges
faster to optimal window size.
This patch converts tp->tcp_mstamp to a plain u64 value storing
a 1 usec TCP clock.
This choice will allow us to upstream the 1 usec TS option as
discussed in IETF 97.
[1] https://www.ietf.org/proceedings/97/slides/slides-97-tcpm-tcp-options-for-low-latency-00.pdf
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use tcp_jiffies32 instead of tcp_time_stamp, since
tcp_time_stamp will soon be only used for TCP TS option.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use tcp_jiffies32 instead of tcp_time_stamp, since
tcp_time_stamp will soon be only used for TCP TS option.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use tcp_jiffies32 instead of tcp_time_stamp to feed
tp->lsndtime.
tcp_time_stamp will soon be a litle bit more expensive
than simply reading 'jiffies'.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Idea is to later convert tp->tcp_mstamp to a full u64 counter
using usec resolution, so that we can later have fine
grained TCP TS clock (RFC 7323), regardless of HZ value.
We try to refresh tp->tcp_mstamp only when necessary.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BBR congestion control depends on pacing, and pacing is
currently handled by sch_fq packet scheduler for performance reasons,
and also because implemening pacing with FQ was convenient to truly
avoid bursts.
However there are many cases where this packet scheduler constraint
is not practical.
- Many linux hosts are not focusing on handling thousands of TCP
flows in the most efficient way.
- Some routers use fq_codel or other AQM, but still would like
to use BBR for the few TCP flows they initiate/terminate.
This patch implements an automatic fallback to internal pacing.
Pacing is requested either by BBR or use of SO_MAX_PACING_RATE option.
If sch_fq happens to be in the egress path, pacing is delegated to
the qdisc, otherwise pacing is done by TCP itself.
One advantage of pacing from TCP stack is to get more precise rtt
estimations, and less work done from TX completion, since TCP Small
queue limits are not generally hit. Setups with single TX queue but
many cpus might even benefit from this.
Note that unlike sch_fq, we do not take into account header sizes.
Taking care of these headers would add additional complexity for
no practical differences in behavior.
Some performance numbers using 800 TCP_STREAM flows rate limited to
~48 Mbit per second on 40Gbit NIC.
If MQ+pfifo_fast is used on the NIC :
$ sar -n DEV 1 5 | grep eth
14:48:44 eth0 725743.00 2932134.00 46776.76 4335184.68 0.00 0.00 1.00
14:48:45 eth0 725349.00 2932112.00 46751.86 4335158.90 0.00 0.00 0.00
14:48:46 eth0 725101.00 2931153.00 46735.07 4333748.63 0.00 0.00 0.00
14:48:47 eth0 725099.00 2931161.00 46735.11 4333760.44 0.00 0.00 1.00
14:48:48 eth0 725160.00 2931731.00 46738.88 4334606.07 0.00 0.00 0.00
Average: eth0 725290.40 2931658.20 46747.54 4334491.74 0.00 0.00 0.40
$ vmstat 1 5
procs -----------memory---------- ---swap-- -----io---- -system-- ------cpu-----
r b swpd free buff cache si so bi bo in cs us sy id wa st
4 0 0 259825920 45644 2708324 0 0 21 2 247 98 0 0 100 0 0
4 0 0 259823744 45644 2708356 0 0 0 0 2400825 159843 0 19 81 0 0
0 0 0 259824208 45644 2708072 0 0 0 0 2407351 159929 0 19 81 0 0
1 0 0 259824592 45644 2708128 0 0 0 0 2405183 160386 0 19 80 0 0
1 0 0 259824272 45644 2707868 0 0 0 32 2396361 158037 0 19 81 0 0
Now use MQ+FQ :
lpaa23:~# echo fq >/proc/sys/net/core/default_qdisc
lpaa23:~# tc qdisc replace dev eth0 root mq
$ sar -n DEV 1 5 | grep eth
14:49:57 eth0 678614.00 2727930.00 43739.13 4033279.14 0.00 0.00 0.00
14:49:58 eth0 677620.00 2723971.00 43674.69 4027429.62 0.00 0.00 1.00
14:49:59 eth0 676396.00 2719050.00 43596.83 4020125.02 0.00 0.00 0.00
14:50:00 eth0 675197.00 2714173.00 43518.62 4012938.90 0.00 0.00 1.00
14:50:01 eth0 676388.00 2719063.00 43595.47 4020171.64 0.00 0.00 0.00
Average: eth0 676843.00 2720837.40 43624.95 4022788.86 0.00 0.00 0.40
$ vmstat 1 5
procs -----------memory---------- ---swap-- -----io---- -system-- ------cpu-----
r b swpd free buff cache si so bi bo in cs us sy id wa st
2 0 0 259832240 46008 2710912 0 0 21 2 223 192 0 1 99 0 0
1 0 0 259832896 46008 2710744 0 0 0 0 1702206 198078 0 17 82 0 0
0 0 0 259830272 46008 2710596 0 0 0 0 1696340 197756 1 17 83 0 0
4 0 0 259829168 46024 2710584 0 0 16 0 1688472 197158 1 17 82 0 0
3 0 0 259830224 46024 2710408 0 0 0 0 1692450 197212 0 18 82 0 0
As expected, number of interrupts per second is very different.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Van Jacobson <vanj@google.com>
Cc: Jerry Chu <hkchu@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christoph Paasch from Apple found another firewall issue for TFO:
After successful 3WHS using TFO, server and client starts to exchange
data. Afterwards, a 10s idle time occurs on this connection. After that,
firewall starts to drop every packet on this connection.
The fix for this issue is to extend existing firewall blackhole detection
logic in tcp_write_timeout() by removing the mss check.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Vyukov reported a divide by 0 triggered by syzkaller, exploiting
tcp_disconnect() path that was never really considered and/or used
before syzkaller ;)
I was not able to reproduce the bug, but it seems issues here are the
three possible actions that assumed they would never trigger on a
listener.
1) tcp_write_timer_handler
2) tcp_delack_timer_handler
3) MTU reduction
Only IPv6 MTU reduction was properly testing TCP_CLOSE and TCP_LISTEN
states from tcp_v6_mtu_reduced()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the support of RFC5827 early retransmit (i.e.,
fast recovery on small inflight with <3 dupacks) because it is
subsumed by the new RACK loss detection. More specifically when
RACK receives DUPACKs, it'll arm a reordering timer to start fast
recovery after a quarter of (min)RTT, hence it covers the early
retransmit except RACK does not limit itself to specific inflight
or dupack numbers.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes RACK install a reordering timer when it suspects
some packets might be lost, but wants to delay the decision
a little bit to accomodate reordering.
It does not create a new timer but instead repurposes the existing
RTO timer, because both are meant to retransmit packets.
Specifically it arms a timer ICSK_TIME_REO_TIMEOUT when
the RACK timing check fails. The wait time is set to
RACK.RTT + RACK.reo_wnd - (NOW - Packet.xmit_time) + fudge
This translates to expecting a packet (Packet) should take
(RACK.RTT + RACK.reo_wnd + fudge) to deliver after it was sent.
When there are multiple packets that need a timer, we use one timer
with the maximum timeout. Therefore the timer conservatively uses
the maximum window to expire N packets by one timeout, instead of
N timeouts to expire N packets sent at different times.
The fudge factor is 2 jiffies to ensure when the timer fires, all
the suspected packets would exceed the deadline and be marked lost
by tcp_rack_detect_loss(). It has to be at least 1 jiffy because the
clock may tick between calling icsk_reset_xmit_timer(timeout) and
actually hang the timer. The next jiffy is to lower-bound the timeout
to 2 jiffies when reo_wnd is < 1ms.
When the reordering timer fires (tcp_rack_reo_timeout): If we aren't
in Recovery we'll enter fast recovery and force fast retransmit.
This is very similar to the early retransmit (RFC5827) except RACK
is not constrained to only enter recovery for small outstanding
flights.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Direct call of tcp_set_keepalive() function from protocol-agnostic
sock_setsockopt() function in net/core/sock.c violates network
layering. And newly introduced protocol (SMC-R) will need its own
keepalive function. Therefore, add "keepalive" function pointer
to "struct proto", and call it from sock_setsockopt() via this pointer.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Utz Bacher <utz.bacher@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tsq_flags being in the same cache line than sk_wmem_alloc
makes a lot of sense. Both fields are changed from tcp_wfree()
and more generally by various TSQ related functions.
Prior patch made room in struct sock and added sk_tsq_flags,
this patch deletes tsq_flags from struct tcp_sock.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code changes txhash (flowlables) on every retransmitted
SYN/ACK, but only after the 2nd retransmitted SYN and only after
tcp_retries1 RTO retransmits.
With this patch:
1) txhash is changed with every SYN retransmits
2) txhash is changed with every RTO.
The result is that we can start re-routing around failed (or very
congested paths) as soon as possible. Otherwise application health
checks may fail and the connection may be terminated before we start
to change txhash.
v4: Removed sysctl, txhash is changed for all RTOs
v3: Removed text saying default value of sysctl is 0 (it is 100)
v2: Added sysctl documentation and cleaned code
Tested with packetdrill tests
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the TFO socket is accepted right off SYN-data, the socket
owner can call getsockopt(TCP_INFO) to collect ongoing SYN-ACK
retransmission or timeout stats (i.e., tcpi_total_retrans,
tcpi_retransmits). Currently those stats are only updated
upon handshake completes. This patch fixes it.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds kernel-doc style descriptions for 6 functions and
fixes 1 typo.
Signed-off-by: Richard Sailer <richard@weltraumpflege.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to to make TCP stack preemptible, as draining prequeue
and backlog queues can take lot of time.
Many SNMP updates were assuming that BH (and preemption) was disabled.
Need to convert some __NET_INC_STATS() calls to NET_INC_STATS()
and some __TCP_INC_STATS() to TCP_INC_STATS()
Before using this_cpu_ptr(net->ipv4.tcp_sk) in tcp_v4_send_reset()
and tcp_v4_send_ack(), we add an explicit preempt disabled section.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename NET_INC_STATS_BH() to __NET_INC_STATS()
and NET_ADD_STATS_BH() to __NET_ADD_STATS()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux TCP stack painfully segments all TSO/GSO packets before retransmits.
This was fine back in the days when TSO/GSO were emerging, with their
bugs, but we believe the dark age is over.
Keeping big packets in write queues, but also in stack traversal
has a lot of benefits.
- Less memory overhead, because write queues have less skbs
- Less cpu overhead at ACK processing.
- Better SACK processing, as lot of studies mentioned how
awful linux was at this ;)
- Less cpu overhead to send the rtx packets
(IP stack traversal, netfilter traversal, drivers...)
- Better latencies in presence of losses.
- Smaller spikes in fq like packet schedulers, as retransmits
are not constrained by TCP Small Queues.
1 % packet losses are common today, and at 100Gbit speeds, this
translates to ~80,000 losses per second.
Losses are often correlated, and we see many retransmit events
leading to 1-MSS train of packets, at the time hosts are already
under stress.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the final part required to namespaceify the tcp
keep alive mechanism.
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is required to have full tcp keepalive mechanism namespace
support.
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different net namespaces might have different requirements as to
the keepalive time of tcp sockets. This might be required in cases
where different firewall rules are in place which require tcp
timeout sockets to be increased/decreased independently of the host.
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix incrementing TCPFastOpenActiveFailed snmp stats multiple times
when the handshake experiences multiple SYN timeouts.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some middle-boxes black-hole the data after the Fast Open handshake
(https://www.ietf.org/proceedings/94/slides/slides-94-tcpm-13.pdf).
The exact reason is unknown. The work-around is to disable Fast Open
temporarily after multiple recurring timeouts with few or no data
delivered in the established state.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The alive parameter of tcp_orphan_retries, indicates
whether the connection is assumed alive or not.
In the function and all places calling it is used as a boolean value.
Therefore this changes the type of alive to bool in the function
definition and all calling locations.
Since tcp_orphan_tries is a tcp_timer.c local function no change in
any other file or header is necessary.
Signed-off-by: Richard Sailer <richard@weltraumpflege.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 900f65d361 ("tcp: move duplicate code from
tcp_v4_init_sock()/tcp_v6_init_sock()"), we no longer
need to export tcp_init_xmit_timers()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce an optimized version of sk_under_memory_pressure()
for TCP. Our intent is to use it in fast paths.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Diagnosing problems related to Window Probes has been hard because
we lack a counter.
TCPWinProbe counts the number of ACK packets a sender has to send
at regular intervals to make sure a reverse ACK packet opening back
a window had not been lost.
TCPKeepAlive counts the number of ACK packets sent to keep TCP
flows alive (SO_KEEPALIVE)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fast Open has been using an experimental option with a magic number
(RFC6994). This patch makes the client by default use the RFC7413
option (34) to get and send Fast Open cookies. This patch makes
the client solicit cookies from a given server first with the
RFC7413 option. If that fails to elicit a cookie, then it tries
the RFC6994 experimental option. If that also fails, it uses the
RFC7413 option on all subsequent connect attempts. If the server
returns a Fast Open cookie then the client caches the form of the
option that successfully elicited a cookie, and uses that form on
later connects when it presents that cookie.
The idea is to gradually obsolete the use of experimental options as
the servers and clients upgrade, while keeping the interoperability
meanwhile.
Signed-off-by: Daniel Lee <Longinus00@gmail.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not needed, and req->sk_listener points to the listener anyway.
request_sock argument can be const.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the major issue for TCP is the SYNACK rtx handling,
done by inet_csk_reqsk_queue_prune(), fired by the keepalive
timer of a TCP_LISTEN socket.
This function runs for awful long times, with socket lock held,
meaning that other cpus needing this lock have to spin for hundred of ms.
SYNACK are sent in huge bursts, likely to cause severe drops anyway.
This model was OK 15 years ago when memory was very tight.
We now can afford to have a timer per request sock.
Timer invocations no longer need to lock the listener,
and can be run from all cpus in parallel.
With following patch increasing somaxconn width to 32 bits,
I tested a listener with more than 4 million active request sockets,
and a steady SYNFLOOD of ~200,000 SYN per second.
Host was sending ~830,000 SYNACK per second.
This is ~100 times more what we could achieve before this patch.
Later, we will get rid of the listener hash and use ehash instead.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per RFC4821 7.3. Selecting Probe Size, a probe timer should
be armed once probing has converged. Once this timer expired,
probing again to take advantage of any path PMTU change. The
recommended probing interval is 10 minutes per RFC1981. Probing
interval could be sysctled by sysctl_tcp_probe_interval.
Eric Dumazet suggested to implement pseudo timer based on 32bits
jiffies tcp_time_stamp instead of using classic timer for such
rare event.
Signed-off-by: Fan Du <fan.du@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packetization Layer Path MTU Discovery works separately beside
Path MTU Discovery at IP level, different net namespace has
various requirements on which one to chose, e.g., a virutalized
container instance would require TCP PMTU to probe an usable
effective mtu for underlying tunnel, while the host would
employ classical ICMP based PMTU to function.
Hence making TCP PMTU mechanism per net namespace to decouple
two functionality. Furthermore the probe base MSS should also
be configured separately for each namespace.
Signed-off-by: Fan Du <fan.du@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the more common dynamic_debug capable net_dbg_ratelimited
and remove the LIMIT_NETDEBUG macro.
All messages are still ratelimited.
Some KERN_<LEVEL> uses are changed to KERN_DEBUG.
This may have some negative impact on messages that were
emitted at KERN_INFO that are not not enabled at all unless
DEBUG is defined or dynamic_debug is enabled. Even so,
these messages are now _not_ emitted by default.
This also eliminates the use of the net_msg_warn sysctl
"/proc/sys/net/core/warnings". For backward compatibility,
the sysctl is not removed, but it has no function. The extern
declaration of net_msg_warn is removed from sock.h and made
static in net/core/sysctl_net_core.c
Miscellanea:
o Update the sysctl documentation
o Remove the embedded uses of pr_fmt
o Coalesce format fragments
o Realign arguments
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we have two different policies for orphan sockets
that repeatedly stall on zero window ACKs. If a socket gets
a zero window ACK when it is transmitting data, the RTO is
used to probe the window. The socket is aborted after roughly
tcp_orphan_retries() retries (as in tcp_write_timeout()).
But if the socket was idle when it received the zero window ACK,
and later wants to send more data, we use the probe timer to
probe the window. If the receiver always returns zero window ACKs,
icsk_probes keeps getting reset in tcp_ack() and the orphan socket
can stall forever until the system reaches the orphan limit (as
commented in tcp_probe_timer()). This opens up a simple attack
to create lots of hanging orphan sockets to burn the memory
and the CPU, as demonstrated in the recent netdev post "TCP
connection will hang in FIN_WAIT1 after closing if zero window is
advertised." http://www.spinics.net/lists/netdev/msg296539.html
This patch follows the design in RTO-based probe: we abort an orphan
socket stalling on zero window when the probe timer reaches both
the maximum backoff and the maximum RTO. For example, an 100ms RTT
connection will timeout after roughly 153 seconds (0.3 + 0.6 +
.... + 76.8) if the receiver keeps the window shut. If the orphan
socket passes this check, but the system already has too many orphans
(as in tcp_out_of_resources()), we still abort it but we'll also
send an RST packet as the connection may still be active.
In addition, we change TCP_USER_TIMEOUT to cover (life or dead)
sockets stalled on zero-window probes. This changes the semantics
of TCP_USER_TIMEOUT slightly because it previously only applies
when the socket has pending transmission.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reported-by: Andrey Dmitrov <andrey.dmitrov@oktetlabs.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
icsk_rto is a 32bit field, and icsk_backoff can reach 15 by default,
or more if some sysctl (eg tcp_retries2) are changed.
Better use 64bit to perform icsk_rto << icsk_backoff operations
As Joe Perches suggested, add a helper for this.
Yuchung spotted the tcp_v4_err() case.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 740b0f1841 ("tcp: switch rtt estimations to usec resolution"),
we no longer need to maintain timestamps in two different fields.
TCP_SKB_CB(skb)->when can be removed, as same information sits in skb_mstamp.stamp_jiffies
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit reduces spurious retransmits due to apparent SACK reneging
by only reacting to SACK reneging that persists for a short delay.
When a sequence space hole at snd_una is filled, some TCP receivers
send a series of ACKs as they apparently scan their out-of-order queue
and cumulatively ACK all the packets that have now been consecutiveyly
received. This is essentially misbehavior B in "Misbehaviors in TCP
SACK generation" ACM SIGCOMM Computer Communication Review, April
2011, so we suspect that this is from several common OSes (Windows
2000, Windows Server 2003, Windows XP). However, this issue has also
been seen in other cases, e.g. the netdev thread "TCP being hoodwinked
into spurious retransmissions by lack of timestamps?" from March 2014,
where the receiver was thought to be a BSD box.
Since snd_una would temporarily be adjacent to a previously SACKed
range in these scenarios, this receiver behavior triggered the Linux
SACK reneging code path in the sender. This led the sender to clear
the SACK scoreboard, enter CA_Loss, and spuriously retransmit
(potentially) every packet from the entire write queue at line rate
just a few milliseconds before the ACK for each packet arrives at the
sender.
To avoid such situations, now when a sender sees apparent reneging it
does not yet retransmit, but rather adjusts the RTO timer to give the
receiver a little time (max(RTT/2, 10ms)) to send us some more ACKs
that will restore sanity to the SACK scoreboard. If the reneging
persists until this RTO then, as before, we clear the SACK scoreboard
and enter CA_Loss.
A 10ms delay tolerates a receiver sending such a stream of ACKs at
56Kbit/sec. And to allow for receivers with slower or more congested
paths, we wait for at least RTT/2.
We validated the resulting max(RTT/2, 10ms) delay formula with a mix
of North American and South American Google web server traffic, and
found that for ACKs displaying transient reneging:
(1) 90% of inter-ACK delays were less than 10ms
(2) 99% of inter-ACK delays were less than RTT/2
In tests on Google web servers this commit reduced reneging events by
75%-90% (as measured by the TcpExtTCPSACKReneging counter), without
any measurable impact on latency for user HTTP and SPDY requests.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the following snmp stats:
TCPFastOpenActiveFail: Fast Open attempts (SYN/data) failed beacuse
the remote does not accept it or the attempts timed out.
TCPSynRetrans: number of SYN and SYN/ACK retransmits to break down
retransmissions into SYN, fast-retransmits, timeout retransmits, etc.
TCPOrigDataSent: number of outgoing packets with original data (excluding
retransmission but including data-in-SYN). This counter is different from
TcpOutSegs because TcpOutSegs also tracks pure ACKs. TCPOrigDataSent is
more useful to track the TCP retransmission rate.
Change TCPFastOpenActive to track only successful Fast Opens to be symmetric to
TCPFastOpenPassive.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: Lawrence Brakmo <brakmo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fast Open currently has a fall back feature to address SYN-data being
dropped but it requires the middle-box to pass on regular SYN retry
after SYN-data. This is implemented in commit aab487435 ("net-tcp:
Fast Open client - detecting SYN-data drops")
However some NAT boxes will drop all subsequent packets after first
SYN-data and blackholes the entire connections. An example is in
commit 356d7d8 "netfilter: nf_conntrack: fix tcp_in_window for Fast
Open".
The sender should note such incidents and fall back to use the regular
TCP handshake on subsequent attempts temporarily as well: after the
second SYN timeouts the original Fast Open SYN is most likely lost.
When such an event recurs Fast Open is disabled based on the number of
recurrences exponentially.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP listener refactoring, part 4 :
To speed up inet lookups, we moved IPv4 addresses from inet to struct
sock_common
Now is time to do the same for IPv6, because it permits us to have fast
lookups for all kind of sockets, including upcoming SYN_RECV.
Getting IPv6 addresses in TCP lookups currently requires two extra cache
lines, plus a dereference (and memory stall).
inet6_sk(sk) does the dereference of inet_sk(__sk)->pinet6
This patch is way bigger than its IPv4 counter part, because for IPv4,
we could add aliases (inet_daddr, inet_rcv_saddr), while on IPv6,
it's not doable easily.
inet6_sk(sk)->daddr becomes sk->sk_v6_daddr
inet6_sk(sk)->rcv_saddr becomes sk->sk_v6_rcv_saddr
And timewait socket also have tw->tw_v6_daddr & tw->tw_v6_rcv_saddr
at the same offset.
We get rid of INET6_TW_MATCH() as INET6_MATCH() is now the generic
macro.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch series refactor the F-RTO feature (RFC4138/5682).
This is to simplify the loss recovery processing. Existing F-RTO
was developed during the experimental stage (RFC4138) and has
many experimental features. It takes a separate code path from
the traditional timeout processing by overloading CA_Disorder
instead of using CA_Loss state. This complicates CA_Disorder state
handling because it's also used for handling dubious ACKs and undos.
While the algorithm in the RFC does not change the congestion control,
the implementation intercepts congestion control in various places
(e.g., frto_cwnd in tcp_ack()).
The new code implements newer F-RTO RFC5682 using CA_Loss processing
path. F-RTO becomes a small extension in the timeout processing
and interfaces with congestion control and Eifel undo modules.
It lets congestion control (module) determines how many to send
independently. F-RTO only chooses what to send in order to detect
spurious retranmission. If timeout is found spurious it invokes
existing Eifel undo algorithms like DSACK or TCP timestamp based
detection.
The first patch removes all F-RTO code except the sysctl_tcp_frto is
left for the new implementation. Since CA_EVENT_FRTO is removed, TCP
westwood now computes ssthresh on regular timeout CA_EVENT_LOSS event.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the second of the TLP patch series; it augments the basic TLP
algorithm with a loss detection scheme.
This patch implements a mechanism for loss detection when a Tail
loss probe retransmission plugs a hole thereby masking packet loss
from the sender. The loss detection algorithm relies on counting
TLP dupacks as outlined in Sec. 3 of:
http://tools.ietf.org/html/draft-dukkipati-tcpm-tcp-loss-probe-01
The basic idea is: Sender keeps track of TLP "episode" upon
retransmission of a TLP packet. An episode ends when the sender receives
an ACK above the SND.NXT (tracked by tlp_high_seq) at the time of the
episode. We want to make sure that before the episode ends the sender
receives a "TLP dupack", indicating that the TLP retransmission was
unnecessary, so there was no loss/hole that needed plugging. If the
sender gets no TLP dupack before the end of the episode, then it reduces
ssthresh and the congestion window, because the TLP packet arriving at
the receiver probably plugged a hole.
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch series implement the Tail loss probe (TLP) algorithm described
in http://tools.ietf.org/html/draft-dukkipati-tcpm-tcp-loss-probe-01. The
first patch implements the basic algorithm.
TLP's goal is to reduce tail latency of short transactions. It achieves
this by converting retransmission timeouts (RTOs) occuring due
to tail losses (losses at end of transactions) into fast recovery.
TLP transmits one packet in two round-trips when a connection is in
Open state and isn't receiving any ACKs. The transmitted packet, aka
loss probe, can be either new or a retransmission. When there is tail
loss, the ACK from a loss probe triggers FACK/early-retransmit based
fast recovery, thus avoiding a costly RTO. In the absence of loss,
there is no change in the connection state.
PTO stands for probe timeout. It is a timer event indicating
that an ACK is overdue and triggers a loss probe packet. The PTO value
is set to max(2*SRTT, 10ms) and is adjusted to account for delayed
ACK timer when there is only one oustanding packet.
TLP Algorithm
On transmission of new data in Open state:
-> packets_out > 1: schedule PTO in max(2*SRTT, 10ms).
-> packets_out == 1: schedule PTO in max(2*RTT, 1.5*RTT + 200ms)
-> PTO = min(PTO, RTO)
Conditions for scheduling PTO:
-> Connection is in Open state.
-> Connection is either cwnd limited or no new data to send.
-> Number of probes per tail loss episode is limited to one.
-> Connection is SACK enabled.
When PTO fires:
new_segment_exists:
-> transmit new segment.
-> packets_out++. cwnd remains same.
no_new_packet:
-> retransmit the last segment.
Its ACK triggers FACK or early retransmit based recovery.
ACK path:
-> rearm RTO at start of ACK processing.
-> reschedule PTO if need be.
In addition, the patch includes a small variation to the Early Retransmit
(ER) algorithm, such that ER and TLP together can in principle recover any
N-degree of tail loss through fast recovery. TLP is controlled by the same
sysctl as ER, tcp_early_retrans sysctl.
tcp_early_retrans==0; disables TLP and ER.
==1; enables RFC5827 ER.
==2; delayed ER.
==3; TLP and delayed ER. [DEFAULT]
==4; TLP only.
The TLP patch series have been extensively tested on Google Web servers.
It is most effective for short Web trasactions, where it reduced RTOs by 15%
and improved HTTP response time (average by 6%, 99th percentile by 10%).
The transmitted probes account for <0.5% of the overall transmissions.
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
Minor conflict between the BCM_CNIC define removal in net-next
and a bug fix added to net. Based upon a conflict resolution
patch posted by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
For passive TCP connections using TCP_DEFER_ACCEPT facility,
we incorrectly increment req->retrans each time timeout triggers
while no SYNACK is sent.
SYNACK are not sent for TCP_DEFER_ACCEPT that were established (for
which we received the ACK from client). Only the last SYNACK is sent
so that we can receive again an ACK from client, to move the req into
accept queue. We plan to change this later to avoid the useless
retransmit (and potential problem as this SYNACK could be lost)
TCP_INFO later gives wrong information to user, claiming imaginary
retransmits.
Decouple req->retrans field into two independent fields :
num_retrans : number of retransmit
num_timeout : number of timeouts
num_timeout is the counter that is incremented at each timeout,
regardless of actual SYNACK being sent or not, and used to
compute the exponential timeout.
Introduce inet_rtx_syn_ack() helper to increment num_retrans
only if ->rtx_syn_ack() succeeded.
Use inet_rtx_syn_ack() from tcp_check_req() to increment num_retrans
when we re-send a SYNACK in answer to a (retransmitted) SYN.
Prior to this patch, we were not counting these retransmits.
Change tcp_v[46]_rtx_synack() to increment TCP_MIB_RETRANSSEGS
only if a synack packet was successfully queued.
Reported-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Julian Anastasov <ja@ssi.bg>
Cc: Vijay Subramanian <subramanian.vijay@gmail.com>
Cc: Elliott Hughes <enh@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A packet with an invalid ack_seq may cause a TCP Fast Open socket to switch
to the unexpected TCP_CLOSING state, triggering a BUG_ON kernel panic.
When a FIN packet with an invalid ack_seq# arrives at a socket in
the TCP_FIN_WAIT1 state, rather than discarding the packet, the current
code will accept the FIN, causing state transition to TCP_CLOSING.
This may be a small deviation from RFC793, which seems to say that the
packet should be dropped. Unfortunately I did not expect this case for
Fast Open hence it will trigger a BUG_ON panic.
It turns out there is really nothing bad about a TFO socket going into
TCP_CLOSING state so I could just remove the BUG_ON statements. But after
some thought I think it's better to treat this case like TCP_SYN_RECV
and return a RST to the confused peer who caused the unacceptable ack_seq
to be generated in the first place.
Signed-off-by: H.K. Jerry Chu <hkchu@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch builds on top of the previous patch to add the support
for TFO listeners. This includes -
1. allocating, properly initializing, and managing the per listener
fastopen_queue structure when TFO is enabled
2. changes to the inet_csk_accept code to support TFO. E.g., the
request_sock can no longer be freed upon accept(), not until 3WHS
finishes
3. allowing a TCP_SYN_RECV socket to properly poll() and sendmsg()
if it's a TFO socket
4. properly closing a TFO listener, and a TFO socket before 3WHS
finishes
5. supporting TCP_FASTOPEN socket option
6. modifying tcp_check_req() to use to check a TFO socket as well
as request_sock
7. supporting TCP's TFO cookie option
8. adding a new SYN-ACK retransmit handler to use the timer directly
off the TFO socket rather than the listener socket. Note that TFO
server side will not retransmit anything other than SYN-ACK until
the 3WHS is completed.
The patch also contains an important function
"reqsk_fastopen_remove()" to manage the somewhat complex relation
between a listener, its request_sock, and the corresponding child
socket. See the comment above the function for the detail.
Signed-off-by: H.K. Jerry Chu <hkchu@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modern TCP stack highly depends on tcp_write_timer() having a small
latency, but current implementation doesn't exactly meet the
expectations.
When a timer fires but finds the socket is owned by the user, it rearms
itself for an additional delay hoping next run will be more
successful.
tcp_write_timer() for example uses a 50ms delay for next try, and it
defeats many attempts to get predictable TCP behavior in term of
latencies.
Use the recently introduced tcp_release_cb(), so that the user owning
the socket will call various handlers right before socket release.
This will permit us to post a followup patch to address the
tcp_tso_should_defer() syndrome (some deferred packets have to wait
RTO timer to be transmitted, while cwnd should allow us to send them
sooner)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Cc: H.K. Jerry Chu <hkchu@google.com>
Cc: John Heffner <johnwheffner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implementing the advanced early retransmit (sysctl_tcp_early_retrans==2).
Delays the fast retransmit by an interval of RTT/4. We borrow the
RTO timer to implement the delay. If we receive another ACK or send
a new packet, the timer is cancelled and restored to original RTO
value offset by time elapsed. When the delayed-ER timer fires,
we enter fast recovery and perform fast retransmit.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add #define pr_fmt(fmt) as appropriate.
Add "IPv4: ", "TCP: ", and "IPsec: " to appropriate files.
Standardize on "UDPLite: " for appropriate uses.
Some prefixes were previously "UDPLITE: " and "UDP-Lite: ".
Add KBUILD_MODNAME ": " to icmp and gre.
Remove embedded prefixes as appropriate.
Add missing "\n" to pr_info in gre.c.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of our machines were reporting:
TCP: too many of orphaned sockets
even when the number of orphaned sockets was well below the
limit.
We print a different message depending on whether we're out
of TCP memory or there are too many orphaned sockets.
Also move the check out of line and cleanup the messages
that were printed.
Signed-off-by: Arun Sharma <asharma@fb.com>
Suggested-by: Mohan Srinivasan <mohan@fb.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: David Miller <davem@davemloft.net>
Cc: Glauber Costa <glommer@parallels.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DaveM said:
Please, this kind of stuff rots forever and not using bool properly
drives me crazy.
Joe Perches <joe@perches.com> gave me the spatch script:
@@
bool b;
@@
-b = 0
+b = false
@@
bool b;
@@
-b = 1
+b = true
I merely installed coccinelle, read the documentation and took credit.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces all uses of struct sock fields' memory_pressure,
memory_allocated, sockets_allocated, and sysctl_mem to acessor
macros. Those macros can either receive a socket argument, or a mem_cgroup
argument, depending on the context they live in.
Since we're only doing a macro wrapping here, no performance impact at all is
expected in the case where we don't have cgroups disabled.
Signed-off-by: Glauber Costa <glommer@parallels.com>
Reviewed-by: Hiroyouki Kamezawa <kamezawa.hiroyu@jp.fujitsu.com>
CC: David S. Miller <davem@davemloft.net>
CC: Eric W. Biederman <ebiederm@xmission.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of testing defined(CONFIG_IPV6) || defined(CONFIG_IPV6_MODULE)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was enabled by default and the messages guarded
by the define are useful.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now, TCP_CHECK_TIMER is not used for debuging, it does nothing.
And, it has been there for several years, maybe 6 years.
Remove it to keep code clearer.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As CWR is stronger than CA_Disorder state, we can miscount
SACK/Reno failure into other timeouts. Not a bad problem as
it can happen only due to ECN, FRTO detecting spurious RTO
or xmit error which are the only callers of tcp_enter_cwr.
And even then losses and RTO must still follow thereafter
to actually end up into the relevant code paths.
Compile tested.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes kernel Bugzilla Bug 18952
This patch adds a syn_set parameter to the retransmits_timed_out()
routine and updates its callers. If not set, TCP_RTO_MIN is taken
as the calculation basis as before. If set, TCP_TIMEOUT_INIT is
used instead, so that sysctl_syn_retries represents the actual
amount of SYN retransmissions in case no SYNACKs are received when
establishing a new connection.
Signed-off-by: Damian Lukowski <damian@tvk.rwth-aachen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides a "user timeout" support as described in RFC793. The
socket option is also needed for the the local half of RFC5482 "TCP User
Timeout Option".
TCP_USER_TIMEOUT is a TCP level socket option that takes an unsigned int,
when > 0, to specify the maximum amount of time in ms that transmitted
data may remain unacknowledged before TCP will forcefully close the
corresponding connection and return ETIMEDOUT to the application. If
0 is given, TCP will continue to use the system default.
Increasing the user timeouts allows a TCP connection to survive extended
periods without end-to-end connectivity. Decreasing the user timeouts
allows applications to "fail fast" if so desired. Otherwise it may take
upto 20 minutes with the current system defaults in a normal WAN
environment.
The socket option can be made during any state of a TCP connection, but
is only effective during the synchronized states of a connection
(ESTABLISHED, FIN-WAIT-1, FIN-WAIT-2, CLOSE-WAIT, CLOSING, or LAST-ACK).
Moreover, when used with the TCP keepalive (SO_KEEPALIVE) option,
TCP_USER_TIMEOUT will overtake keepalive to determine when to close a
connection due to keepalive failure.
The option does not change in anyway when TCP retransmits a packet, nor
when a keepalive probe will be sent.
This option, like many others, will be inherited by an acceptor from its
listener.
Signed-off-by: H.K. Jerry Chu <hkchu@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Anton Blanchard when we use
percpu_counter_read_positive() to make our orphan socket limit checks,
the check can be off by up to num_cpus_online() * batch (which is 32
by default) which on a 128 cpu machine can be as large as the default
orphan limit itself.
Fix this by doing the full expensive sum check if the optimized check
triggers.
Reported-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
CodingStyle cleanups
EXPORT_SYMBOL should immediately follow the symbol declaration.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 1122 says the following:
...
Keep-alive packets MUST only be sent when no data or
acknowledgement packets have been received for the
connection within an interval.
...
The acknowledgement packet is reseting the keepalive
timer but the data packet isn't. This patch fixes it by
checking the timestamp of the last received data packet
too when the keepalive timer expires.
Signed-off-by: Flavio Leitner <fleitner@redhat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
With latest CONFIG_PROVE_RCU stuff, I felt more comfortable to make this
work.
sk->sk_dst_cache is currently protected by a rwlock (sk_dst_lock)
This rwlock is readlocked for a very small amount of time, and dst
entries are already freed after RCU grace period. This calls for RCU
again :)
This patch converts sk_dst_lock to a spinlock, and use RCU for readers.
__sk_dst_get() is supposed to be called with rcu_read_lock() or if
socket locked by user, so use appropriate rcu_dereference_check()
condition (rcu_read_lock_held() || sock_owned_by_user(sk))
This patch avoids two atomic ops per tx packet on UDP connected sockets,
for example, and permits sk_dst_lock to be much less dirtied.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
This patch will make TCP use only linear timeouts if the
stream is thin. This will help to avoid the very high latencies
that thin stream suffer because of exponential backoff. This
mechanism is only active if enabled by iocontrol or syscontrol
and the stream is identified as thin. A maximum of 6 linear
timeouts is tried before exponential backoff is resumed.
Signed-off-by: Andreas Petlund <apetlund@simula.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently we don't increment SYN-ACK timeouts & retransmissions
although we do increment the same stats for SYN. We seem to have lost
the SYN-ACK accounting with the introduction of tcp_syn_recv_timer
(commit 2248761e in the netdev-vger-cvs tree).
This patch fixes this issue. In the process we also rename the v4/v6
syn/ack retransmit functions for clarity. We also add a new
request_socket operations (syn_ack_timeout) so we can keep code in
inet_connection_sock.c protocol agnostic.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves retransmits_timed_out() from include/net/tcp.h
to tcp_timer.c, where it is used.
Reported-by: Frederic Leroy <fredo@starox.org>
Signed-off-by: Damian Lukowski <damian@tvk.rwth-aachen.de>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
dst_negative_advice() should check for changed dst and reset
sk_tx_queue_mapping accordingly. Pass sock to the callers of
dst_negative_advice.
(sk_reset_txq is defined just for use by dst_negative_advice. The
only way I could find to get around this is to move dst_negative_()
from dst.h to dst.c, include sock.h in dst.c, etc)
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to have better cache layouts of struct sock (separate zones
for rx/tx paths), we need this preliminary patch.
Goal is to transfert fields used at lookup time in the first
read-mostly cache line (inside struct sock_common) and move sk_refcnt
to a separate cache line (only written by rx path)
This patch adds inet_ prefix to daddr, rcv_saddr, dport, num, saddr,
sport and id fields. This allows a future patch to define these
fields as macros, like sk_refcnt, without name clashes.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 1122 specifies two threshold values R1 and R2 for connection timeouts,
which may represent a number of allowed retransmissions or a timeout value.
Currently linux uses sysctl_tcp_retries{1,2} to specify the thresholds
in number of allowed retransmissions.
For any desired threshold R2 (by means of time) one can specify tcp_retries2
(by means of number of retransmissions) such that TCP will not time out
earlier than R2. This is the case, because the RTO schedule follows a fixed
pattern, namely exponential backoff.
However, the RTO behaviour is not predictable any more if RTO backoffs can be
reverted, as it is the case in the draft
"Make TCP more Robust to Long Connectivity Disruptions"
(http://tools.ietf.org/html/draft-zimmermann-tcp-lcd).
In the worst case TCP would time out a connection after 3.2 seconds, if the
initial RTO equaled MIN_RTO and each backoff has been reverted.
This patch introduces a function retransmits_timed_out(N),
which calculates the timeout of a TCP connection, assuming an initial
RTO of MIN_RTO and N unsuccessful, exponentially backed-off retransmissions.
Whenever timeout decisions are made by comparing the retransmission counter
to some value N, this function can be used, instead.
The meaning of tcp_retries2 will be changed, as many more RTO retransmissions
can occur than the value indicates. However, it yields a timeout which is
similar to the one of an unpatched, exponentially backing off TCP in the same
scenario. As no application could rely on an RTO greater than MIN_RTO, there
should be no risk of a regression.
Signed-off-by: Damian Lukowski <damian@tvk.rwth-aachen.de>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here, an ICMP host/network unreachable message, whose payload fits to
TCP's SND.UNA, is taken as an indication that the RTO retransmission has
not been lost due to congestion, but because of a route failure
somewhere along the path.
With true congestion, a router won't trigger such a message and the
patched TCP will operate as standard TCP.
This patch reverts one RTO backoff, if an ICMP host/network unreachable
message, whose payload fits to TCP's SND.UNA, arrives.
Based on the new RTO, the retransmission timer is reset to reflect the
remaining time, or - if the revert clocked out the timer - a retransmission
is sent out immediately.
Backoffs are only reverted, if TCP is in RTO loss recovery, i.e. if
there have been retransmissions and reversible backoffs, already.
Changes from v2:
1) Renaming of skb in tcp_v4_err() moved to another patch.
2) Reintroduced tcp_bound_rto() and __tcp_set_rto().
3) Fixed code comments.
Signed-off-by: Damian Lukowski <damian@tvk.rwth-aachen.de>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce keepalive_probes(tp) helper, and use it, like
keepalive_time_when(tp) and keepalive_intvl_when(tp)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Redundant checks made indentation impossible to follow.
However, it might be useful to make this ca_state+is_sack
indexed array.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original message was unhelpful and extremely alarming to our poor
users, despite its charm. Make it less frightening.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using one atomic_t per protocol, use a percpu_counter
for "orphan_count", to reduce cache line contention on
heavy duty network servers.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller