Signed-off-by: Paolo Pisati <paolo.pisati@canonical.com>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Having a linear_min_sel setting means the first linear_min_sel selectors are
invalid. We need to subtract linear_min_sel when use n_voltages to determinate
if regulator can change voltage.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Introduce a regulator_can_change_voltage() function for the subsytems or
drivers which might check if applying voltage change is possible and use
special workaround code when the driver is used with fixed regulators or
regulators with disabled ability to change the voltage.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some drivers (at least 3 drivers) have such variant of linear mapping that
the first few selectors are invalid and the reset are linear mapping.
Let's support this case in core.
This patch adds linear_min_sel in struct regulator_desc,
so we can allow specific minimal selector for starting linear mapping.
Then extends regulator_[map|list]_voltage_linear() to support this feature.
Note that for selectors less than min_linear_index, we need count them to
n_voltages so regulator_list_voltage() won't fail while checking the boundary
for selector before calling list_voltage callback.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
regulator_is_supported_voltage() should return true only if the voltage
of fixed/constant regulator is between min_uV and max_uV.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
When regulator_register fails and exits through the scrub path the
regulator_put function was called whilst holding the
regulator_list_mutex, causing deadlock.
This patch adds a private version of the regulator_put function which
can be safely called whilst holding the mutex, replacing the
aforementioned call.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the gpio_request_one() fails, or returns EPROBE_DEFER, the
regulator must be device_unregister()ed. When this is not done,
there are WARNING: from sysfs:
WARNING: at fs/sysfs/file.c:343 sysfs_open_file+0x238/0x268()
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some regulators can set any voltage within the constraints range,
not being limited to specified operating points.
This patch makes it possible to describe such regulator and makes
the regulator_is_supported_voltage() function behave correctly.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pull workqueue changes from Tejun Heo:
"This is workqueue updates for v3.7-rc1. A lot of activities this
round including considerable API and behavior cleanups.
* delayed_work combines a timer and a work item. The handling of the
timer part has always been a bit clunky leading to confusing
cancelation API with weird corner-case behaviors. delayed_work is
updated to use new IRQ safe timer and cancelation now works as
expected.
* Another deficiency of delayed_work was lack of the counterpart of
mod_timer() which led to cancel+queue combinations or open-coded
timer+work usages. mod_delayed_work[_on]() are added.
These two delayed_work changes make delayed_work provide interface
and behave like timer which is executed with process context.
* A work item could be executed concurrently on multiple CPUs, which
is rather unintuitive and made flush_work() behavior confusing and
half-broken under certain circumstances. This problem doesn't
exist for non-reentrant workqueues. While non-reentrancy check
isn't free, the overhead is incurred only when a work item bounces
across different CPUs and even in simulated pathological scenario
the overhead isn't too high.
All workqueues are made non-reentrant. This removes the
distinction between flush_[delayed_]work() and
flush_[delayed_]_work_sync(). The former is now as strong as the
latter and the specified work item is guaranteed to have finished
execution of any previous queueing on return.
* In addition to the various bug fixes, Lai redid and simplified CPU
hotplug handling significantly.
* Joonsoo introduced system_highpri_wq and used it during CPU
hotplug.
There are two merge commits - one to pull in IRQ safe timer from
tip/timers/core and the other to pull in CPU hotplug fixes from
wq/for-3.6-fixes as Lai's hotplug restructuring depended on them."
Fixed a number of trivial conflicts, but the more interesting conflicts
were silent ones where the deprecated interfaces had been used by new
code in the merge window, and thus didn't cause any real data conflicts.
Tejun pointed out a few of them, I fixed a couple more.
* 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (46 commits)
workqueue: remove spurious WARN_ON_ONCE(in_irq()) from try_to_grab_pending()
workqueue: use cwq_set_max_active() helper for workqueue_set_max_active()
workqueue: introduce cwq_set_max_active() helper for thaw_workqueues()
workqueue: remove @delayed from cwq_dec_nr_in_flight()
workqueue: fix possible stall on try_to_grab_pending() of a delayed work item
workqueue: use hotcpu_notifier() for workqueue_cpu_down_callback()
workqueue: use __cpuinit instead of __devinit for cpu callbacks
workqueue: rename manager_mutex to assoc_mutex
workqueue: WORKER_REBIND is no longer necessary for idle rebinding
workqueue: WORKER_REBIND is no longer necessary for busy rebinding
workqueue: reimplement idle worker rebinding
workqueue: deprecate __cancel_delayed_work()
workqueue: reimplement cancel_delayed_work() using try_to_grab_pending()
workqueue: use mod_delayed_work() instead of __cancel + queue
workqueue: use irqsafe timer for delayed_work
workqueue: clean up delayed_work initializers and add missing one
workqueue: make deferrable delayed_work initializer names consistent
workqueue: cosmetic whitespace updates for macro definitions
workqueue: deprecate system_nrt[_freezable]_wq
workqueue: deprecate flush[_delayed]_work_sync()
...
Many regulators support a bypass mode where they simply switch their
input supply to the output. This is mainly used in low power retention
states where power consumption is extremely low so higher voltage or
less clean supplies can be used.
Support this by providing ops for the drivers and a consumer API which
allows the device to be put into bypass mode if all consumers enable it
and the machine enables permission for this.
This is not supported as a mode since the existing modes are rarely used
due to fuzzy definition and mostly redundant with modern hardware which is
able to respond promptly to load changes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Graeme Gregory <gg@slimlogic.co.uk>
If the device doesn't have a regmap specified by the driver and we can't
find one on the device itself try its parent, providing a useful defualt
for many MFDs.
[Rewrite commit message -- broonie]
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Users (especially framework code) may end up passing in a zero deferral
time depending on runtime conditions or configuration. If they do then
just call regulator_disable() directly to save scheduling.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
If a regulator only supports a single voltage list_voltage() can be used
to report what that voltage is so add this as one of the criteria for
creating the microvolts file in sysfs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix regulator kernel-doc warnings:
Warning(drivers/regulator/core.c:2308): No description found for parameter 'rdev'
Warning(drivers/regulator/core.c:2308): Excess function parameter 'regulator' description in 'regulator_set_voltage_time_sel'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
flush[_delayed]_work_sync() are now spurious. Mark them deprecated
and convert all users to flush[_delayed]_work().
If you're cc'd and wondering what's going on: Now all workqueues are
non-reentrant and the regular flushes guarantee that the work item is
not pending or running on any CPU on return, so there's no reason to
use the sync flushes at all and they're going away.
This patch doesn't make any functional difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mattia Dongili <malattia@linux.it>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Petr Vandrovec <petr@vandrovec.name>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Avi Kivity <avi@redhat.com>
Fix regulator kernel-doc warnings:
Warning(drivers/regulator/core.c:2308): No description found for parameter 'rdev'
Warning(drivers/regulator/core.c:2308): Excess function parameter 'regulator' description in 'regulator_set_voltage_time_sel'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 65f735082d ("regulator: core: Add core support for GPIO controlled
enable lines") introduced enable gpio entry in regulator configuration
structure. Some drivers use '-1' as a placeholder for marking that such
gpio line is not available, because '0' is considered as a valid gpio
number. This patch fixes initialization of such drivers (like MAX8952
on UniversalC210 board), when '-1' is provided as enable gpio pin in the
regulator's platform data.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the regulator doesn't supply a way of reading back the voltage but does
provide a list_voltage() operation then use that with a selector of zero
to read the voltage. Regulators doing this means that we have the list
operation there for consumers that want to configure themselves.
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This prevents the output of just
dummy:
in the boot log. Now it says:
regulator-dummy: no parameters
which at least doesn't make it look like an accidental printk and also doesn't
only use "dummy" which could mean anything.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is to address the following warning during compilation time: (Compile on x86_64)
CC drivers/regulator/core.o
drivers/regulator/core.c: In function '_regulator_do_set_voltage':
drivers/regulator/core.c:2183:10: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
This patch adds a temporary variable to avoid double cast.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When registering the regulator and setting supply for the regulator
then increment open_count to reflect correct number of users.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The most important feature of this patch set is the new async infrastructure
that makes sure async_synchronize_full() synchronizes all domains and allows
us to remove all the hacks (like having scsi_complete_async_scans() in the
device base code) and means that the async infrastructure will "just work" in
future. The rest is assorted driver updates (aacraid, bnx2fc, virto-scsi,
megaraid, bfa, lpfc, qla2xxx, qla4xxx) plus a lot of infrastructure work in
sas and FC.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQDjDCAAoJEDeqqVYsXL0M/sMH/jVgBfF1mjR+DQuTscKyD21w
0BQLn5OmvDZDqo44iqQzNRObw7CxkBkUtHoozsknLijw+KggER653ZOAtUdIHfI/
/uo7iJQ3J3D/Ezm99HYSpZiF2juZwsBRtFBoKkGqOpMlzFUx5o4hUbH5OcINxnHR
VmvJU5K1kg8D77Q6zK+Atl14/Rfibc2IoufFmbYdplUAM/tV0BpBSSHJAJvqua76
NGMl4KJcPZnXe/4LXcxZia5A2efdFFEzaQ2mM9rUVEAgHDAxc0Zg9IoDhGd08FX4
G55NK+6+bKb9s7bgyva0T/iy817TRCzjteeYNFrb8nBRe7aQbAivaBHQFXIyvdQ=
=y2sh
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"The most important feature of this patch set is the new async
infrastructure that makes sure async_synchronize_full() synchronizes
all domains and allows us to remove all the hacks (like having
scsi_complete_async_scans() in the device base code) and means that
the async infrastructure will "just work" in future.
The rest is assorted driver updates (aacraid, bnx2fc, virto-scsi,
megaraid, bfa, lpfc, qla2xxx, qla4xxx) plus a lot of infrastructure
work in sas and FC.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (97 commits)
[SCSI] Revert "[SCSI] fix async probe regression"
[SCSI] cleanup usages of scsi_complete_async_scans
[SCSI] queue async scan work to an async_schedule domain
[SCSI] async: make async_synchronize_full() flush all work regardless of domain
[SCSI] async: introduce 'async_domain' type
[SCSI] bfa: Fix to set correct return error codes and misc cleanup.
[SCSI] aacraid: Series 7 Async. (performance) mode support
[SCSI] aha152x: Allow use on 64bit systems
[SCSI] virtio-scsi: Add vdrv->scan for post VIRTIO_CONFIG_S_DRIVER_OK LUN scanning
[SCSI] bfa: squelch lockdep complaint with a spin_lock_init
[SCSI] qla2xxx: remove unnecessary reads of PCI_CAP_ID_EXP
[SCSI] qla4xxx: remove unnecessary read of PCI_CAP_ID_EXP
[SCSI] ufs: fix incorrect return value about SUCCESS and FAILED
[SCSI] ufs: reverse the ufshcd_is_device_present logic
[SCSI] ufs: use module_pci_driver
[SCSI] usb-storage: update usb devices for write cache quirk in quirk list.
[SCSI] usb-storage: add support for write cache quirk
[SCSI] set to WCE if usb cache quirk is present.
[SCSI] virtio-scsi: hotplug support for virtio-scsi
[SCSI] virtio-scsi: split scatterlist per target
...
This is in preparation for teaching async_synchronize_full() to sync all
pending async work, and not just on the async_running domain. This
conversion is functionally equivalent, just embedding the existing list
in a new async_domain type.
The .registered attribute is used in a later patch to distinguish
between domains that want to be flushed by async_synchronize_full()
versus those that only expect async_synchronize_{full|cookie}_domain to
be used for flushing.
[jejb: add async.h to scsi_priv.h for struct async_domain]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
REGULATOR_STATUS_UNDEFINED is to be returned by regulator, if any other state
doesn't really apply.
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Case REGULATOR_STATUS_STANDBY -> REGULATOR_MODE_STANDBY.
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since DT doesn't provide an idiomatic mechanism for enabling full
constraints and since it's much more natural with DT to provide them
just assume that a DT enabled system has full constraints.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
With changes introduced by commit 222cc7b (regulator: core: Allow
multiple requests of a single supply mapping) on create_regulator,
regulator_put needs a corresponding update on sysfs entry removing.
Also regulator->dev still needs to get assigned in create_regulator,
otherwise, sysfs_remove_link call in regulator_put will get bypassed.
Reported-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It is very common for regulators to support having their enable signal
controlled by a GPIO. Since there are a bunch of fiddly things to get
right like handling the operations when the enable signal is tied to
a rail and it's just replicated code add support for this to the core.
Drivers should set ena_gpio in their config if they have a GPIO control,
using ena_gpio_flags to specify any flags (including GPIOF_OUT_INIT_ for
the initial state) and ena_gpio_invert if the GPIO is active low. The
core will then override any enable and disable operations the driver has
and instead control the specified GPIO.
This will in the future also allow us to further extend the core by
identifying when several enable signals have been tied together and
handling this properly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Create new _regulator_do_enable() and _regulator_do_disable() operations
which deal with the mechanics of performing the enable and disable, partly
to cut down on the levels of indentation and partly to support some future
work.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Many regulators have a fixed specification for their enable time. Allow
this to be set in the regulator_desc as a number to save them having to
implement an explicit operation.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lots of regulator drivers have checks in their map_voltage() functions
to verify that the result of the mapping is in the range originally
specified. Factor these out in the core and provide a bit of extra
defensiveness for other drivers by doing the check in the core.
Since we're now doing a list_voltage() earlier move the current mapping
back to a voltage out into the set_voltage() call to save redoing it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently regulator_is_supported_voltage() works by enumerating the set
of voltages which can be set by the regulator but the checks we're doing
to impose constraints mean that if we can't vary the voltage we'll not
report any voltages as supported even though the regulator is actually
set at that voltage.
We could fix the voltage listing but this would mean that list_voltage()
could end up going to the hardware to get the current voltage which isn't
expected (it's supposed to be very cheap) so instead special case things
when we can't change the voltage and compare the requested range against
the current voltage.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A recursive lockdep warning occurs if you call
regulator_set_optimum_mode() on a regulator with a supply because
there is no nesting annotation for the rdev->mutex. To avoid this
warning, get the supply's load before locking the regulator's
mutex to avoid grabbing the same class of lock twice.
=============================================
[ INFO: possible recursive locking detected ]
3.4.0 #3257 Tainted: G W
---------------------------------------------
swapper/0/1 is trying to acquire lock:
(&rdev->mutex){+.+.+.}, at: [<c036e9e0>] regulator_get_voltage+0x18/0x38
but task is already holding lock:
(&rdev->mutex){+.+.+.}, at: [<c036ef38>] regulator_set_optimum_mode+0x24/0x224
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&rdev->mutex);
lock(&rdev->mutex);
*** DEADLOCK ***
May be due to missing lock nesting notation
3 locks held by swapper/0/1:
#0: (&__lockdep_no_validate__){......}, at: [<c03dbb48>] __driver_attach+0x40/0x8c
#1: (&__lockdep_no_validate__){......}, at: [<c03dbb58>] __driver_attach+0x50/0x8c
#2: (&rdev->mutex){+.+.+.}, at: [<c036ef38>] regulator_set_optimum_mode+0x24/0x224
stack backtrace:
[<c001521c>] (unwind_backtrace+0x0/0x12c) from [<c00cc4d4>] (validate_chain+0x760/0x1080)
[<c00cc4d4>] (validate_chain+0x760/0x1080) from [<c00cd744>] (__lock_acquire+0x950/0xa10)
[<c00cd744>] (__lock_acquire+0x950/0xa10) from [<c00cd990>] (lock_acquire+0x18c/0x1e8)
[<c00cd990>] (lock_acquire+0x18c/0x1e8) from [<c080c248>] (mutex_lock_nested+0x68/0x3c4)
[<c080c248>] (mutex_lock_nested+0x68/0x3c4) from [<c036e9e0>] (regulator_get_voltage+0x18/0x38)
[<c036e9e0>] (regulator_get_voltage+0x18/0x38) from [<c036efb8>] (regulator_set_optimum_mode+0xa4/0x224)
...
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
commit 222cc7b1 (regulator: core: Allow multiple requests of a single supply mapping)
removed the usage of get_device_regulator().
Remove the function definition too amd get rid of the following warning:
drivers/regulator/core.c:112:26: warning: 'get_device_regulator' defined but not used [-Wunused-function]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Sometimes it may be useful to allow a device to request a supply multiple
times, for example in order to allow framework management of some uses of
the supply with some additional driver specific management or in order to
allow multiple children of an MFD to work with the supply. Currently this
is not possible due to the creation of
Solve this by removing the requested_uA entry (we have no current users
of this feature anyway) and ignoring errors creating the symlink to the
consumer. We should do something nicer than this as this causes sysfs to
spew enormous warnings but it allows users to run for now.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
There is no need to consider waiting for the voltage to ramp if we
didn't manage to set it and looking at the return value is going to be
cheaper than is_enabled().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJP53AxAAoJEHm+PkMAQRiGs2QH/RaqkXz96fwjhDcyiKpDqA3c
kGuS5mz5cOhnqKSmR88HFm6pwuhLux/qSJzeAmoQy1MC8a0ACx7AnANW0lfN3/qe
/HGYz8h60yCL/fhn8/bUYtdt9xsoDqoDcq/ooFl9mcsJGWbC6WeMSZU5dAUYqviE
qFrp5zjY07FG53CRGT0hFpezQNwNL+VLH30CF9LD+fJLPVEYum2zBNGXWM42rcw5
fxzGL/6SO8YqA/Upic1ht6HAd6s5LOrlST7qvnyXUMvRXN5z/Y92ueYJZefkS1Om
ohuLIKM2bv9/dJS67H8N2baSKGCzBdfSe5/5WaHdLYW9MiVju0wRl6HPJtAMrkk=
=H8t8
-----END PGP SIGNATURE-----
Merge tag 'v3.5-rc4' into regulator-drivers
Linux 3.5-rc4 contains patches which conflict with some of the
development work.
With this change, regulator_set_voltage_time_sel() can be more generic and not
limited to linear and table based mapping now.
One side-effect of this change is that list_voltage() must be implemented.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This change makes it possible to set ramp_delay with 0.xxx mV/uS without
truncation issue.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For table based mapping, we can calculate voltage difference by below equation:
abs(rdev->desc->volt_table[new_selector] - rdev->desc->volt_table[old_selector])
Thus we can make regulator_set_voltage_time_sel work for table based mapping.
regulator_set_voltage_time_sel() only supports linear or table based mapping.
In case it is misused, also warn if neither linear nor table based mapping
is used with regulator_set_voltage_time_sel().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For some hardwares ramp_delay for BUCKs is a configurable parameter which can
be configured through DT or board file.This patch adds ramp_delay to regulator
constraints and allow user to configure it for regulators which supports this
feature, through DT or board file. It will provide two ways of setting the
ramp_delay for a regulator:
First, by setting it as constraints in board file(for configurable
regulators) and set_machine_constraints() will take care of setting it on
hardware by calling(the provided) .set_ramp_delay() operation(callback).
Second, by setting it as data in regulator_desc(as fixed/default
ramp_delay rate) for a regulator in driver.
regulator_set_voltage_time_sel() will give preference to
constraints->ramp_delay while reading ramp_delay rate for regulator. Similarly
users should also take care accordingly while refering ramp_delay rate(in case
of implementing their private .set_voltage_time_sel() callbacks for different
regulators).
[Rewrote subject for 80 columns -- broonie]
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
minor optimization: move delay code to where delay is set and
thus where it is used vs in the main line path.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Acked-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The voltage being set should be passed to the call in handler
requesting the callback. Currently this is not done.
The calling handler cannot call regulator_get_voltage() to get the
information since the mutex is held by the regulator and
deadlock occurs.
Without this change the receiver of the call in cannot know what
action to take. This is used, for example, to set PAD voltages
when doing SD vccq voltage changes.
[Review and spelling fix in the commit log from Pankaj Jangra]
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
rdev->desc->uV_step * abs(new_selector - old_selector) returns uV.
The unit of ramp_delay is mV/us.
Current code multiples 1000 at wrong place.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds regulator_set_voltage_time_sel(), to move into core, the
commonly used code by drivers to provide the .set_voltage_time_sel callback.
It will also allow us to configure different ramp delay for different
regulators easily.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fixed voltage is a kind of linear mapping where n_voltages is 1.
This change allows [list|map]_voltage_linear to be used for fixed
voltage.
For fixed voltage, n_voltages is 1 and the only valid selector is 0.
Thus we actually don't care the uV_step setting.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Properly handle the case if the specified min_uV is less than the voltage given
by the lowest selector.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If no regmap is explicitly specified then use dev_get_regmap() to obtain
one. The driver must explicitly enable any actual usage of the regmap
so there's no concern with unwanted usage.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
devres_release() will call the destructor for the resource as well as
freeing the devres data.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
If the regulator is not on, it won't take time setting new voltage.
So only call set_voltage_time_sel() to get the necessary delay when
the regulator is on.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some regulator hardware use table based mapping can set volt_table in
regulator_desc and use regulator_list_voltage_table() for their list_voltage
callback.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The major thing here is the addition of some helpers to factor code out
of drivers, making a fair proportion of regulators much more just data
rather than code which is nice.
- Helpers in the core for regulators using regmap, providing generic
implementations of the enable and voltage selection operations which
just need data to describe them in the drivers.
- Split out voltage mapping and voltage setting, allowing many more
drivers to take advantage of the infrastructure for selectors.
- Loads and loads of cleanups from Axel Lin once again, including many
changes to take advantage of the above new framework features
- New drivers for Ricoh RC5T583, TI TPS62362, TI TPS62363, TI TPS65913,
TI TWL6035 and TI TWL6037.
Some of the registration changes to support the core refactoring caused
so many conflicts that eventually topic branches were abandoned for this
release.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=UR7s
-----END PGP SIGNATURE-----
Merge tag 'regulator-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"The major thing here is the addition of some helpers to factor code
out of drivers, making a fair proportion of regulators much more just
data rather than code which is nice.
- Helpers in the core for regulators using regmap, providing generic
implementations of the enable and voltage selection operations which
just need data to describe them in the drivers.
- Split out voltage mapping and voltage setting, allowing many more
drivers to take advantage of the infrastructure for selectors.
- Loads and loads of cleanups from Axel Lin once again, including many
changes to take advantage of the above new framework features
- New drivers for Ricoh RC5T583, TI TPS62362, TI TPS62363, TI
TPS65913, TI TWL6035 and TI TWL6037.
Some of the registration changes to support the core refactoring
caused so many conflicts that eventually topic branches were abandoned
for this release."
* tag 'regulator-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (227 commits)
regulator: tps65910: use of_node of matched regulator being register
regulator: tps65910: dt: support when "regulators" node found
regulator: tps65910: add error message in case of failure
regulator: tps62360: dt: initialize of_node param for regulator register.
regulator: tps65910: use devm_* for memory allocation
regulator: tps65910: use small letter for regulator names
mfd: tpx6586x: Depend on regulator
regulator: regulator for Palmas Kconfig
regulator: regulator driver for Palmas series chips
regulator: Enable Device Tree for the db8500-prcmu regulator driver
regulator: db8500-prcmu: Separate regulator registration from probe
regulator: ab3100: Use regulator_map_voltage_iterate()
regulator: tps65217: Convert to set_voltage_sel and map_voltage
regulator: Enable the ab8500 for Device Tree
regulator: ab8500: Split up probe() into manageable pieces
regulator: max8925: Remove check_range function and max_uV from struct rc5t583_regulator_info
regulator: max8649: Remove unused check_range() function
regulator: rc5t583: Remove max_uV from struct rc5t583_regulator_info
regulator: da9052: Convert to set_voltage_sel and map_voltage
regulator: max8952: Use devm_kzalloc
...
If we fail while registering a regulator make sure we release the supply
for the regulator if there is one.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Cc: stable@vger.kernel.org
Integer division may truncate the result.
Use DIV_ROUND_UP to ensure simple linear voltage mappings falls within the
specified range.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A lot of regulator hardware maps selectors on to voltages with a simple
linear mapping function
selector = base + (selector * step size)
Provide off the shelf list_voltage() and map_voltage() operations which
use new min_uV and uV_step members in the regulator_desc to implement
this function.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
In order to allow more drivers to factor things out into data allow
drivers to provide a mapping function to convert voltages into selectors.
This allows any driver to use set_voltage_sel(). The existing mapping
based on iterating over list_voltage() is provided as an operation which
can be assigned to the new map_voltage() function though for ease of
transition it is treated as the default.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The core really wants a struct device to be supplied for regulators and
there's no reason this should be impossible so provide one so complain
if we didn't get one.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
It turns out that (quite surprisingly) devres_destroy() only undoes the
devres mapping, it doesn't destroy the underlying resource, meaning that
anything using devm_regulator_put() would leak. While we wait for the new
devres_release() which does what we want to get merged open code it in
devm_regulator_put().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
If a regulator is always on for any reason then cache that when the
consumer is created and use it to optimise away the need to take locks
or recurse up the supply tree when consumers do enable or disable calls.
The scheduling of asynchronous work for bulk enables is also skipped.
We don't actually check if the device physically supports control on the
basis that constraints allowing status changes on physically always on
regulators are nonsensical anyway.
This is a very common pattern in hardware - it's normal to have some
power supplies that have either no software control or are critical to
system function - so many systems should be able to benefit.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
regulator_set_optimum_mode needs set_mode to properly work.
Add checking for set_mode callback in case it may be not implemented.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since the enable(), disable() and is_enabled() operations for most regmap
based regulators come down to reading and updating a single register bit
we can factor out the code and allow these drivers to just define which
bit to update using the enable_reg and enable_mask fields in their desc
and then use operations provided by the core.
As well as the code saving this opens the door to future optimisation of
the bulk operations - if the core can realise that we are updating a
single register for multiple regulators then it should be able to combine
these updates into a single physical operation.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Since the voltage selector operations are intended to directly map a
bitfield in the device register map into regulator API operations the
code for implementing them is usually very standard we can save some
code by providing standard implementations for devices using the regmap
API.
Drivers using regmap can pass their regmap in in the regmap_config
struct, set vsel_reg and vsel_mask in their regulator_desc and then
use regulator_{get,set}_voltage_sel_regmap in their ops. This saves
a small amount of code from each driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Since many regulators use regmap for register I/O and since there's quite
a few very common patterns in the code allow drivers to pass in a regmap
to the core for use in generic code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
In current implementation, to support set_suspend_voltage and set_suspend_mode
the regulator code needs the regulator driver to implement both
set_suspend_enable and set_suspend_disable callbacks.
This patch removes this limitation. In the case set_suspend_enable and/or
set_suspend_disable are NULL, the regulator code assumes we don't need to
do any thing to enable/disable regulator when system is suspended and
then will continue to handle set_suspend_mode and set_suspend_voltage.
Currently the regulator core creates suspend state related sysfs entries only
if both set_suspend_enable and set_suspend_disable callbacks are not NULL.
A side-effect of this change is that the regulator core will create suspend
state related sysfs entries unconditionally now.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When supplied by another regulator, returns the supply regulator's output
voltage for inpu_uV.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We don't support missing configs at all so segfaulting isn't that bad
but since we've got checks in the code move the dereference after them.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than adding new arguments to regulator_register() every time we
want to add a new bit of dynamic information at runtime change the function
to take these via a struct. By doing this we avoid needing to do further
changes like the recent addition of device tree support which required each
regulator driver to be updated to take an additional parameter.
The regulator_desc which should (mostly) be static data is still passed
separately as most drivers are able to configure this statically at build
time.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In currently implementation of _regulator_do_set_voltage, set_voltage_time_sel will
only be called if set_voltage_sel is implemented.
set_voltage_time_sel actually only needs get_voltage_sel to get old_selector.
This patch makes regulator core support set_voltage_time_sel for drivers
implement either set_voltage or set_voltage_sel.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A bunch of smallish fixes that came up during the merge window as
things got more testing - even more fixes from Axel, a fix for error
handling in more complex systems using -EPROBE_DEFER and a couple of
small fixes for the new dummy regulators.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=h5VJ
-----END PGP SIGNATURE-----
Merge tag 'regulator-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A bunch of smallish fixes that came up during the merge window as
things got more testing - even more fixes from Axel, a fix for error
handling in more complex systems using -EPROBE_DEFER and a couple of
small fixes for the new dummy regulators."
* tag 'regulator-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: Remove non-existent parameter from fixed-helper.c kernel doc
regulator: Fix setting new voltage in s5m8767_set_voltage
regulator: fix sysfs name collision between dummy and fixed dummy regulator
regulator: Fix deadlock on removal of regulators with supplies
regulator: Fix comments in include/linux/regulator/machine.h
regulator: Only update [LDOx|DCx]_HIB_MODE bits in wm8350_[ldo|dcdc]_set_suspend_disable
regulator: Fix setting low power mode for wm831x aldo
regulator: Return microamps in wm8350_isink_get_current
regulator: wm8350: Fix the logic to choose best current limit setting
regulator: wm831x-isink: Fix the logic to choose best current limit setting
regulator: wm831x-dcdc: Fix the logic to choose best current limit setting
regulator: anatop: patching to device-tree property "reg".
regulator: Do proper shift to set correct bit for DC[2|5]_HIB_MODE setting
regulator: Fix restoring pmic.dcdcx_hib_mode settings in wm8350_dcdc_set_suspend_enable
regulator: Fix unbalanced lock/unlock in mc13892_regulator_probe error path
regulator: Fix set and get current limit for wm831x_buckv
regulator: tps6586x: Fix list minimal voltage setting for LDO0
Drivers should be able to declare their descriptors const and the framework
shouldn't ever be modifying the desciptor. Make the parameter and the
pointer in regulator_dev const to enforce this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure we always apply the supply mapping when doing a lookup rather than
only doing it in non-DT cases, ensuring that regulators with supplies
specified in the regulator_desc can find their supplies on non-DT systems
and generally making the code more obvious.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When using device tree if there's no binding for a supply then there's no
way that one could appear later so just fail permanently right away. This
avoids wasting time trying to reprobe when that can never work.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When cleaning up after a failed bulk_disable() we try to reenable any
supplies that we did manage to disable - complain if we fail to do that
when we try.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If a regulator with a supply is being unregistered we will call
regulator_put() to release the supply with the regulator_list_mutex held
but this deadlocks as regulator_put() takes the same lock. Fix this by
releasing the supply before we take the mutex in regulator_unregister().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This has been a fairly quiet release from a regulator point of view, the
only real framework features added were devm support and a convenience
helper for setting up fixed voltage regulators.
We also added a couple of drivers (but will drop the BQ240022 driver via
the arm-soc tree as it's been replaced by the more generic
gpio-regulator driver) and Axel Lin continued his relentless and
generally awesome stream of fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=fbBu
-----END PGP SIGNATURE-----
Merge tag 'regulator-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates for 3.4 from Mark Brown:
"This has been a fairly quiet release from a regulator point of view,
the only real framework features added were devm support and a
convenience helper for setting up fixed voltage regulators.
We also added a couple of drivers (but will drop the BQ240022 driver
via the arm-soc tree as it's been replaced by the more generic
gpio-regulator driver) and Axel Lin continued his relentless and
generally awesome stream of fixes and cleanups."
* tag 'regulator-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (93 commits)
regulator: Fix up a confusing dev_warn when DT lookup fails
regulator: Convert tps6507x to set_voltage_sel
regulator: Refactor tps6507x to use one tps6507x_pmic_ops for all LDOs and DCDCs
regulator: Make s5m8767_get_voltage_register always return correct register
regulator: s5m8767: Check pdata->buck[2|3|4]_gpiodvs earlier
regulator: tps65910: Provide settling time for DCDC voltage change
regulator: Add Anatop regulator driver
regulator: Simplify implementation of tps65912_get_voltage_dcdc
regulator: Use tps65912_set_voltage_sel for both DCDCx and LDOx
regulator: tps65910: Provide settling time for enabling rails
regulator: max8925: Use DIV_ROUND_UP macro
regulator: tps65912: Use simple equations to get register address
regulator: Fix the logic of tps65910_get_mode
regulator: Merge tps65217_pmic_ldo234_ops and tps65217_pmic_dcdc_ops to tps65217_pmic_ops
regulator: Use DIV_ROUND_CLOSEST in wm8350_isink_get_current
regulator: Use array to store dcdc_range settings for tps65912
regulator: Rename s5m8767_convert_voltage to s5m8767_convert_voltage_to_sel
regulator: tps6524x: Remove unneeded comment for N_REGULATORS
regulator: Rename set_voltage_sel callback function name to *_sel
regulator: Fix s5m8767_set_voltage_time_sel calculation value
...
of_parse_phandle() returns NULL either if the property name
itself does not exist or if it (exists and) does not
reference a valid phandle.
Giving out a warn like the one below (that the property references
an invalid phandle) can be confusing when the property itself
does not exist in the node.
Fix it with a more sensible message and make it a dev_dbg instead
of a dev_warn.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Paolo Pisati