And audit all the users. None needed the BKL. That was easy
because there was only very few around.
Tested with allmodconfig build on x86-64
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
From: Andi Kleen <ak@linux.intel.com>
With this patch, the LPM capable EHCI host controller can put device
into L1 sleep state which is a mode that can enter/exit quickly, and
reduce power consumption.
Signed-off-by: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Without this fix, a USB 3.0 port is downgraded to full speed after a port
reset of a configured device. The USB 3.0 terminations will be disabled
permanently, and USB 3.0 devices will always enumerate as full speed
devices, until the host controller is unplugged (if it is an ExpressCard)
or the computer is rebooted.
Fajun Chen traced this traced the speed downgrade issue to the port reset
and the interpretation of port status in USB hub driver code. The hub
code was not testing for the port being a SuperSpeed port, and it fell
through to the else case of Full Speed.
The following patch adds SuperSpeed mapping from the port status, and
fixes the speed downgrade issue.
Reported-by: Fajun Chen <fajun.chen@seagate.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When USB3 protocol port detects an USB3.0 device attach, the port will
automatically transition to the Enabled state upon the completion
of successful link training.
Do not disable USB3 protocol ports in hub_activate(), or USB3.0 device
will fail to be recognized if xHCI bus power management is implemented.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1364) avoids enabling remote wakeup by default on all
non-root-hub USB devices. Individual drivers or userspace will have
to enable it wherever it is needed, such as for keyboards or network
interfaces. Note: This affects only system sleep, not autosuspend.
External hubs will continue to relay wakeup requests received from
downstream through their upstream port, even when remote wakeup is not
enabled for the hub itself. Disabling remote wakeup on a hub merely
prevents it from generating wakeup requests in response to connect,
disconnect, and overcurrent events.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1349b) clears up the confusion in many USB host
controller drivers between port features and port statuses. In mosty
cases it's true that the status bit is in the position given by the
corresponding feature value, but that's not always true and it's not
guaranteed in the USB spec.
There's no functional change, just replacing expressions of the form
(1 << USB_PORT_FEAT_x) with USB_PORT_STAT_x, which has the same value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1348) removes the bogus
USB_PORT_FEAT_{HIGHSPEED,SUPERSPEED} symbols from ch11.h. No such
features are defined by the USB spec. (There is a PORT_LOWSPEED
feature, but the spec doesn't mention it except to say that host
software should never use it.) The speed indicators are port
statuses, not port features.
As a temporary workaround for the xhci-hcd driver, a fictional
USB_PORT_STAT_SUPER_SPEED symbol is added.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usbcore headers: hcd.h and hub.h are shared between usbcore,
HCDs and a couple of other drivers (e.g. USBIP modules).
So, it makes sense to move them into a more public location and
to cleanup dependency of those modules on kernel internal headers.
This patch moves hcd.h from drivers/usb/core into include/linux/usb/
Signed-of-by: Eric Lescouet <eric@lescouet.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The id_table field of the struct usb_device_id is constant in <linux/usb.h>
so it is worth to make the initialization data also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Németh Márton <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: Move hcd free_dev call into usb_disconnect
I found a way to oops the kernel:
1. Open a USB device through devio.
2. Remove the hcd module in the host kernel.
3. Close the devio file descriptor.
The problem is that closing the file descriptor does usb_release_dev
as it is the last reference. usb_release_dev then tries to invoke
the hcd free_dev function (or rather dereferencing the hcd driver
struct). This causes an oops as the hcd driver has already been
unloaded so the struct is gone.
This patch tries to fix this by bringing the free_dev call earlier
and into usb_disconnect. I have verified that repeating the
above steps no longer crashes with this patch applied.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1329) converts the USB stack over to the PM core's
runtime PM framework. This involves numerous changes throughout
usbcore, especially to hub.c and driver.c. Perhaps the most notable
change is that CONFIG_USB_SUSPEND now depends on CONFIG_PM_RUNTIME
instead of CONFIG_PM.
Several fields in the usb_device and usb_interface structures are no
longer needed. Some code which used to depend on CONFIG_USB_PM now
depends on CONFIG_USB_SUSPEND (requiring some rearrangement of header
files).
The only visible change in behavior should be that following a system
sleep (resume from RAM or resume from hibernation), autosuspended USB
devices will be resumed just like everything else. They won't remain
suspended. But if they aren't in use then they will naturally
autosuspend again in a few seconds.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1326) adds usb_enable_autosuspend() and
usb_disable_autosuspend() routines for use by drivers. If a driver
knows that its device can handle suspends and resumes correctly, it
can enable autosuspend all by itself. This is equivalent to the user
writing "auto" to the device's power/level attribute.
The implementation differs slightly from what it used to be. Now
autosuspend is disabled simply by doing usb_autoresume_device() (to
increment the usage counter) and enabled by doing
usb_autosuspend_device() (to decrement the usage counter).
The set_level() attribute method is updated to use the new routines,
and the USB Power-Management documentation is updated.
The patch adds a usb_enable_autosuspend() call to the hub driver's
probe routine, allowing the special-case code for hubs in quirks.c to
be removed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1324) makes a small change to the code used for remote
wakeup of root hubs. hcd_resume_work() now calls the hub driver's
remote-wakeup routine instead of implementing its own version.
The patch is complicated by the need to rename remote_wakeup() to
usb_remote_wakeup(), make it non-static, and declare it in a header
file. There's also the additional complication required to make
everything work when CONFIG_PM isn't set; the do-nothing inline
routine had to be moved into the header file.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's really the wireless speed, so rename the thing to make
more sense. Based on a recommendation from David Vrabel
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently a non-root-hub USB device's wakeup settings are initialized when the
device is set to a configured state using device_init_wakeup(), but this is not
correct as wakeup is split into "capable" (can_wakeup) and "enabled"
(should_wakeup). The settings should be initialized instead in the device
initialization (usb_new_device) with the "capable" setting disabled and the
"enabled" setting enabled. The "capable" setting should be set based on the
device being configured or unconfigured, and "enabled" setting set based on
the sysfs power/wakeup control.
This patch retains the sysfs power/wakeup setting of a non-root-hub USB device
over a USB device re-configuration, which can happen (for example) after a
suspend/resume cycle.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a new host controller driver method, reset_device(), that the USB core
will use to notify the host of a successful device reset. The call may
fail due to out-of-memory errors; attempt the port reset sequence again if
that happens. Update hub_port_init() to allow resetting a configured
device.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Set power.async_suspend for USB devices, endpoints and interfaces,
allowing them to be suspended and resumed asynchronously during
system sleep transitions.
The power.async_suspend flag is also set for devices that don't have
suspend or resume callbacks, because otherwise they would make the
main suspend/resume thread wait for their "asynchronous" children
(during suspend) or parents (during resume), effectively negating the
possible gains from executing these devices' suspend and resume
callbacks asynchronously.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Borislav Petkov reports issues with duplicate sysfs endpoint files after a
resume from a hibernate. It turns out that the code to support alternate
settings under xHCI has issues when a device with a non-default alternate
setting is reset during the hibernate:
[ 427.681810] Restarting tasks ...
[ 427.681995] hub 1-0:1.0: state 7 ports 6 chg 0004 evt 0000
[ 427.682019] usb usb3: usb resume
[ 427.682030] ohci_hcd 0000:00:12.0: wakeup root hub
[ 427.682191] hub 1-0:1.0: port 2, status 0501, change 0000, 480 Mb/s
[ 427.682205] usb 1-2: usb wakeup-resume
[ 427.682226] usb 1-2: finish reset-resume
[ 427.682886] done.
[ 427.734658] ehci_hcd 0000:00:12.2: port 2 high speed
[ 427.734663] ehci_hcd 0000:00:12.2: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
[ 427.746682] hub 3-0:1.0: hub_reset_resume
[ 427.746693] hub 3-0:1.0: trying to enable port power on non-switchable hub
[ 427.786715] usb 1-2: reset high speed USB device using ehci_hcd and address 2
[ 427.839653] ehci_hcd 0000:00:12.2: port 2 high speed
[ 427.839666] ehci_hcd 0000:00:12.2: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
[ 427.847717] ohci_hcd 0000:00:12.0: GetStatus roothub.portstatus [1] = 0x00010100 CSC PPS
[ 427.915497] hub 1-2:1.0: remove_intf_ep_devs: if: ffff88022f9e8800 ->ep_devs_created: 1
[ 427.915774] hub 1-2:1.0: remove_intf_ep_devs: bNumEndpoints: 1
[ 427.915934] hub 1-2:1.0: if: ffff88022f9e8800: endpoint devs removed.
[ 427.916158] hub 1-2:1.0: create_intf_ep_devs: if: ffff88022f9e8800 ->ep_devs_created: 0, ->unregistering: 0
[ 427.916434] hub 1-2:1.0: create_intf_ep_devs: bNumEndpoints: 1
[ 427.916609] ep_81: create, parent hub
[ 427.916632] ------------[ cut here ]------------
[ 427.916644] WARNING: at fs/sysfs/dir.c:477 sysfs_add_one+0x82/0x96()
[ 427.916649] Hardware name: System Product Name
[ 427.916653] sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:12.2/usb1/1-2/1-2:1.0/ep_81'
[ 427.916658] Modules linked in: binfmt_misc kvm_amd kvm powernow_k8 cpufreq_ondemand cpufreq_powersave cpufreq_userspace freq_table cpufreq_conservative ipv6 vfat fat
+8250_pnp 8250 pcspkr ohci_hcd serial_core k10temp edac_core
[ 427.916694] Pid: 278, comm: khubd Not tainted 2.6.33-rc2-00187-g08d869a-dirty #13
[ 427.916699] Call Trace:
The problem is caused by a mismatch between the USB core's view of the
device state and the USB device and xHCI host's view of the device state.
After the device reset and re-configuration, the device and the xHCI host
think they are using alternate setting 0 of all interfaces. However, the
USB core keeps track of the old state, which may include non-zero
alternate settings. It uses intf->cur_altsetting to keep the endpoint
sysfs files for the old state across the reset.
The bandwidth allocation functions need to know what the xHCI host thinks
the current alternate settings are, so original patch set
intf->cur_altsetting to the alternate setting 0. This caused duplicate
endpoint files to be created.
The solution is to not set intf->cur_altsetting before calling
usb_set_interface() in usb_reset_and_verify_device(). Instead, we add a
new flag to struct usb_interface to tell usb_hcd_alloc_bandwidth() to use
alternate setting 0 as the currently installed alternate setting.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Borislav Petkov <petkovbb@googlemail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1330) fixes a bug in khbud's handling of remote
wakeups. When a device sends a remote-wakeup request, the parent hub
(or the host controller driver, for directly attached devices) begins
the resume sequence and notifies khubd when the sequence finishes. At
this point the port's SUSPEND feature is automatically turned off.
However the device needs an additional 10-ms resume-recovery time
(TRSMRCY in the USB spec). Khubd does not wait for this delay if the
SUSPEND feature is off, and as a result some devices fail to behave
properly following a remote wakeup. This patch adds the missing
delay to the remote-wakeup path.
It also extends the resume-signalling delay used by ehci-hcd and
uhci-hcd from 20 ms (the value in the spec) to 25 ms (the value we use
for non-remote-wakeup resumes). The extra time appears to help some
devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Cc: Rickard Bellini <rickard.bellini@ericsson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1315) fixes some bugs in the USB core authorization
code:
usb_deauthorize_device() should deallocate the device strings
instead of leaking them, and it should invoke
usb_destroy_configuration() (which does proper reference
counting) instead of freeing the config information directly.
usb_authorize_device() shouldn't change the device strings
until it knows that the authorization will succeed, and it should
autosuspend the device at the end (having autoresumed the
device at the start).
Because the device strings can be changed, the sysfs routines
to display the strings must protect the string pointers by
locking the device.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Acked-by: David Vrabel <david.vrabel@csr.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1314) renames usb_configure_device() and
usb_configure_device_otg() in the hub driver. Neither name is
appropriate because these routines enumerate devices, they don't
configure them. That's handled by usb_choose_configuration() and
usb_set_configuration().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix the following sparse warning:
drivers/usb/core/hub.c:1664:37: warning: Using plain integer as NULL pointer
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make the USB core check the bandwidth when switching from one
interface alternate setting to another. Also check the bandwidth
when resetting a configuration (so that alt setting 0 is used). If
this check fails, the device's state is unchanged. If the device
refuses the new alt setting, re-instate the old alt setting in the
host controller hardware.
If a USB device doesn't have an alternate interface setting 0, install
the first alt setting in its descriptors when a new configuration is
requested, or the device is reset.
Add a mutex per root hub to protect bandwidth operations:
adding/reseting/changing configurations, and changing alternate interface
settings. We want to ensure that the xHCI host controller and the USB
device are set up for the same configurations and alternate settings.
There are two (possibly three) steps to do this:
1. The host controller needs to check that bandwidth is available for a
different setting, by issuing and waiting for a configure endpoint
command.
2. Once that returns successfully, a control message is sent to the
device.
3. If that fails, the host controller must be notified through another
configure endpoint command.
The mutex is used to make these three operations seem atomic, to prevent
another driver from using more bandwidth for a different device while
we're in the middle of these operations.
While we're touching the bandwidth code, rename usb_hcd_check_bandwidth()
to usb_hcd_alloc_bandwidth(). This function does more than just check
that the bandwidth change won't exceed the bus bandwidth; it actually
changes the bandwidth configuration in the xHCI host controller.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1303) revises the USB Power Management infrastructure to
make it compatible with the new driver-model Runtime PM framework:
Drivers are no longer allowed to access intf->pm_usage_cnt
directly; the PM framework manages its own usage counters.
usb_autopm_set_interface() is eliminated, because it directly
sets intf->pm_usage_cnt.
usb_autopm_enable() and usb_autopm_disable() are eliminated,
because they call usb_autopm_set_interface().
usb_autopm_get_interface_no_resume() and
usb_autopm_put_interface_no_suspend() are added. They
correspond to pm_runtime_get_noresume() and
pm_runtime_put_noidle() in the PM framework.
The power/level attribute no longer accepts "suspend", only
"on" and "auto". The PM framework doesn't allow devices to be
forced into a suspended mode.
The hub driver contains the only code that violates the new
guidelines. It is updated to use the new interface routines instead.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1297) adds a "remove" attribute to each USB device's
directory in sysfs. Writing to this attribute causes the device to be
deconfigured (the same as writing 0 to the "bConfigurationValue"
attribute) and then tells the hub driver to disable the device's
upstream port. The device remains locked during these activities so
there is no possibility of it getting reconfigured in between. The
port will remain disabled until after the device is unplugged.
The purpose of this is to provide a means for user programs to imitate
the "Safely remove hardware" applet in Windows. Some devices do
expect their ports to be disabled before they are unplugged, and they
provide visual feedback to users indicating when they can safely be
unplugged.
The security implications are minimal. Writing to the "remove"
attribute is no more dangerous than writing to the
"bConfigurationValue" attribute.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Zeuthen <davidz@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1296) gets rid of the fixed DMA-buffer mapping used by
the hub driver for its status URB. This URB doesn't get used much --
mainly when a device is plugged in or unplugged -- so the dynamic
mapping overhead is minimal. And most systems have many fewer
external hubs than root hubs, which don't need a mapped buffer anyway.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb: better error handling in usb_port_suspend
- disable remote wakeup only if it was enabled
- refuse to autosuspend if remote wakeup fails to be enabled
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1304) fixes a regression in ehci-hcd. Evidently some
hubs don't handle Clear-TT-Buffer requests correctly, so we should
avoid sending them when they don't appear to be absolutely necessary.
The reported symptom is that output on a downstream audio device cuts
out because the hub stops relaying isochronous packets.
The patch prevents Clear-TT-Buffer requests from being sent following
a STALL handshake. In theory a STALL indicates either that the
downstream device sent a STALL or that no matching TT buffer could be
found. In either case, the transfer is completed and the TT buffer
does not remain busy, so it doesn't need to be cleared.
Also, the patch fixes a minor flaw in the code that actually sends the
Clear-TT-Buffer requests. Although the pipe direction isn't really
used for control transfers, it should be a Send rather than a Receive.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Javier Kohen <jkohen@users.sourceforge.net>
CC: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a hook for updating xHCI internal structures after khubd fetches the
hub descriptor and sets up the hub's TT information. The xHCI driver must
update the internal structures before devices under the hub can be
enumerated.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1268) changes the way usbcore handles child devices that
undergo a disconnection and reconnection while the parent hub is
suspended. Currently, if the child isn't enabled for remote wakeup we
leave it alone, figuring that it will go through a reset-resume when
somebody tries to use it.
However this isn't a good approach if the reason for the disconnection
is that the child decided to switch modes or in some other way alter
its descriptors. In that case we want to re-enumerate it as soon as
possible, not wait until somebody forces a reset-resume.
To resolve the issue, this patch treats reconnected suspended child
devices as though they had requested a remote wakeup, even if they
weren't enabled for it. The mode switch or descriptor change will be
detected during the reset part of the reset-resume, and the device
will be re-enumerated immediately.
The disadvantage of this change is that it will cause autosuspended
devices to be resumed when the computer wakes up from a system sleep
during which the root hub was reset or lost power. This shouldn't
matter much; some people would even argue that autosuspended devices
should _always_ be resumed when the system wakes up!
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: "Yang Fei-AFY095" <fei.yang@motorola.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1267) changes usb_kick_khubd() and hdev_to_hub() to make
them more resilient against situations where a hub device isn't bound
to the hub driver. The code assumes that if a root hub was
successfully registered then it must be bound to the hub driver.
But this assumption can fail if the user manually unbinds the hub
driver, or more importantly, if the host controller dies causing
usb_set_configuration to fail.
To protect against these possibilities, make hdev_to_hub() check that
the hub device is configured before dereferencing the active
configuration, and make usb_kick_khubd() check that the pointer to the
hub's private data structure isn't NULL.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1260) changes the pm_usage_cnt field in struct
usb_interface from an int to an atomic_t. This is so that drivers can
invoke the usb_autopm_get_interface_async() and
usb_autopm_put_interface_async() routines without locking and without
fear of corrupting the pm_usage_cnt value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1258) implements a feature that users have been asking
for: It gives programs the ability to "claim" a port on a hub, via a
new usbfs ioctl. A device plugged into a "claimed" port will not be
touched by the kernel beyond the immediate necessities of
initialization and enumeration.
In particular, when a device is plugged into a "claimed" port, the
kernel will not select and install a configuration. And when a config
is installed by usbfs or sysfs, the kernel will not probe any drivers
for any of the interfaces. (However the kernel will fetch various
string descriptors during enumeration. One could argue that this
isn't really necessary, but the strings are exported in sysfs.)
The patch does not guarantee exclusive access to these devices; it is
still possible for more than one program to open the device file
concurrently. Programs are responsible for coordinating access among
themselves.
A demonstration program showing how to use the new interface can be
found in an attachment to
http://marc.info/?l=linux-usb&m=124345857431452&w=2
The patch also makes a small simplification to the hub driver,
replacing a bunch of more-or-less useless variants of "out of memory"
with a single message.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1255) updates the interface for calling
usb_hub_clear_tt_buffer(). Even the name of the function is changed!
When an async URB (i.e., Control or Bulk) going through a high-speed
hub to a non-high-speed device is cancelled or fails, the hub's
Transaction Translator buffer may be left busy still trying to
complete the transaction. The buffer has to be cleared; that's what
usb_hub_clear_tt_buffer() does.
It isn't safe to send any more URBs to the same endpoint until the TT
buffer is fully clear. Therefore the HCD needs to be told when the
Clear-TT-Buffer request has finished. This patch adds a callback
method to struct hc_driver for that purpose, and makes the hub driver
invoke the callback at the proper time.
The patch also changes a couple of names; "hub_tt_kevent" and
"tt.kevent" now look rather antiquated.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add host controller driver API and a slot_id variable to struct
usb_device. This allows the xHCI host controller driver to ask the
hardware to allocate a slot for the device when a struct usb_device is
allocated. The slot needs to be allocated at that point because the
hardware can run out of internal resources, and we want to know that very
early in the device connection process. Don't call this new API for root
hubs, since they aren't real devices.
Add HCD API to let the host controller choose the device address. This is
especially important for xHCI hardware running in a virtualized
environment. The guests running under the VM don't need to know which
addresses on the bus are taken, because the hardware picks the address for
them. Announce SuperSpeed USB devices after the address has been assigned
by the hardware.
Don't use the new get descriptor/set address scheme with xHCI. Unless
special handling is done in the host controller driver, the xHC can't
issue control transfers before you set the device address. Support for
the older addressing scheme will be added when the xHCI driver supports
the Block Set Address Request (BSR) flag in the Address Device command.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB 3.0 bus specification defines a new connection sequence for USB 3.0
hubs and roothubs. USB 3.0 devices are reset and link trained by the hub
before the port status change notification is sent to the host OS. This means
that an entire tree of devices can be trained in parallel on power up, and the
OS no longer needs to reset USB 3.0 devices. Change the USB core's hub port
init sequence so that it does not reset USB 3.0 devices.
The port status change from the roothub and from the USB 3.0 hub will report
the SuperSpeed connect correctly. This patch currently only handles the
roothub case.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add USB 3.0 root hub descriptors. This is a kludge because I reused the old
USB 2.0 descriptors, instead of using the new USB 3.0 hub descriptors with
endpoint companion descriptors and other descriptors. I did this because I
wasn't ready to add USB 3.0 hub changes to khubd. For now, a USB 3.0 roothub
looks like a USB 2.0 roothub, with a higher speed.
USB 3.0 hubs have no transaction translator (TT).
Make USB core debugging handle super speed ports.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Modify the USB core to handle the new USB 3.0 speed, "SuperSpeed". This
is 5.0 Gbps (wire speed). There are probably more places that check for
speed that I've missed.
SuperSpeed devices have a 512 byte endpoint 0 max packet size. This shows
up as a bMaxPacketSize0 set to 0x09 (see table 9-8 of the USB 3.0 bus
spec).
xHCI spec says that the xHC can handle intervals up to 2^15 microframes. That
might change when real silicon becomes available.
Add FIXME note for SuperSpeed isochronous endpoints. They can transmit up
to 16 packets in one "burst" before they wait for an acknowledgment of the
packets. They can do up to 3 bursts per microframe (determined by the
mult value in the endpoint companion descriptor). The xHCI driver doesn't
have support for isoc yet, so fix this later.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix sparse warning in drivers/usb/core/hub.c.
The following sparse warning is seen when building on ARM due
do the macro raw_local_irq_save():
warning: symbol 'temp' shadows an earlier one
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
transfer_buffer_length and actual_length have become unsigned, therefore some
additional conversion of local variables, function arguments and print
specifications is desired.
A test for a negative urb->transfer_buffer_length became obsolete; instead
we ensure that it does not exceed INT_MAX. Also, urb->actual_length is always
less than urb->transfer_buffer_length.
rh_string() does no longer return -EPIPE in the case of an unsupported ID.
Instead its only caller, rh_call_control() does the check.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1221) changes the way usbcore reinitializes a device
following a reset or a reset-resume. Currently we call
usb_set_interface() for every interface in the active configuration;
this is to put the interface into the same altsetting as before the
reset and to make sure that the host's endpoint state matches the
device's endpoint state.
However, sending a Set-Interface request is a waste of time if an
interface was already in altsetting 0 before the reset, since it is
certainly in altsetting 0 afterward. In addition, many devices can't
handle Set-Interface requests -- they crash when they receive them.
So instead, the patch adds code to check each interface. If the
interface wasn't in altsetting 0 before the reset, we go head with the
Set-Interface request as before. But if it was then we skip sending
the Set-Interface request, and we clear out the host-side endpoint
state by calling usb_disable_interface() followed by
usb_enable_interface().
The patch also adds a couple of new comments to explain what's going
on.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To permit a userspace application to associate with WUSB devices
using numeric association, control transfers to unauthenticated WUSB
devices must be allowed.
This requires that wusbcore correctly sets the device state to
UNAUTHENTICATED, DEFAULT and ADDRESS and that control transfers can be
performed to UNAUTHENTICATED devices.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The base versions handle constant folding now.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1200) finishes some fixes that were left incomplete by
an earlier patch.
Although nobody has addressed this issue in the past, it turns out
that we need to distinguish between two different modes of disabling
and enabling endpoints. In one mode only the data structures in
usbcore are affected, and in the other mode the host controller and
device hardware states are affected as well.
The earlier patch added an extra argument to the routines in the
enable_endpoint pathways to reflect this difference. This patch adds
corresponding arguments to the disable_endpoint pathways. Without
this change, the endpoint toggle state can get out of sync between
the host and the device. The exact mechanism depends on the details
of the host controller (whether or not it stores its own copy of the
toggle values).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Dan Streetman <ddstreet@ieee.org>
Tested-by: Dan Streetman <ddstreet@ieee.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Carry out the PM-routine interface change in the USB OTG pathway. This
was omitted from the earlier interface-change patch by mistake.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg KH <greg@kroah.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as1197) fixes an error introduced recently. Since a
significant number of devices can't handle Set-Interface requests, we
no longer call usb_set_interface() when a driver unbinds from an
interface, provided the interface is already in altsetting 0. However
the interface still does get disabled, and the call to
usb_set_interface() was the only thing re-enabling it. Since the
interface doesn't get re-enabled, further attempts to use it fail.
So the patch adds a call to usb_enable_interface() when a driver
unbinds and the interface is in altsetting 0. For this to work
right, the interface's endpoints have to be re-enabled but their
toggles have to be left alone. Therefore an additional argument is
added to usb_enable_endpoint() and usb_enable_interface(), a flag
indicating whether or not the endpoint toggles should be reset.
This is a forward-ported version of a patch which fixes Bugzilla
#12301.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: David Roka <roka@dawid.hu>
Reported-by: Erik Ekman <erik@kryo.se>
Tested-by: Erik Ekman <erik@kryo.se>
Tested-by: Alon Bar-Lev <alon.barlev@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1185) makes usbcore take advantage of the bus
notifications sent out by the driver core. Now we can create all our
device and interface attribute files before the device or interface
uevent is broadcast.
A side effect is that we no longer create the endpoint "pseudo"
devices at the same time as a device or interface is registered -- it
seems like a bad idea to try registering an endpoint before the
registration of its parent is complete. So the routines for creating
and removing endpoint devices have been split out and renamed, and
they are called explicitly when needed. A new bitflag is used for
keeping track of whether or not the interface's endpoint devices have
been created, since (just as with the interface attributes) they vary
with the altsetting and hence can be changed at random times.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: make printk messages more searchable
Make USB printk messages long and straightforward. One of these
decorated USB error messages cost me non-trivial efforts to locate.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1177) modifies the USB core suspend and resume
routines. The resume functions now will take a pm_message_t argument,
so they will know what sort of resume is occurring. The new argument
is also passed to the port suspend/resume and bus suspend/resume
routines (although they don't use it for anything but debugging).
In addition, special pm_message_t values are used for user-initiated,
device-initiated (i.e., remote wakeup), and automatic suspend/resume.
By testing these values, drivers can tell whether or not a particular
suspend was an autosuspend. Unfortunately, they can't do the same for
resumes -- not until the pm_message_t argument is also passed to the
drivers' resume methods. That will require a bigger change.
IMO, the whole Power Management framework should have been set up this
way in the first place.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1166) changes usb_new_device(). Now new devices will be
announced in the log _prior_ to being registered; this way the "new
device" lines will appear before all the output from driver probing,
which seems much more logical.
Also, the patch adds a call to usb_stop_pm() to the failure pathway,
so that the parent's count of unsuspended children will remain correct
if registration fails. In order for this to work properly, the code
to increment that count has to be moved forward, before the first
point where a failure can occur.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch introduces a new call to be able to do a USB reset from an
atomic contect. This is quite helpful in USB callbacks to handle
errors (when the only thing that can be done is to do a device
reset).
It is done queuing a work struct that will do the actual reset. The
struct is "attached" to an interface so pending requests from an
interface are removed when said interface is unbound from the driver.
The call flow then becomes:
usb_queue_reset_device()
__usb_queue_reset_device() [workqueue]
usb_reset_device()
usb_probe_interface()
usb_cancel_queue_reset() [error path]
usb_unbind_interface()
usb_cancel_queue_reset()
usb_driver_release_interface()
usb_cancel_queue_reset()
Note usb_cancel_queue_reset() needs smarts to try not to unqueue when
it is actually being executed. This happens when we run the reset from
the workqueue: usb_reset_device() is called and on interface unbind
time, usb_cancel_queue_reset() would be called. That would deadlock on
cancel_work_sync(). To avoid that, we set (before running
usb_reset_device()) usb_intf->reset_running and clear it inmediately
after returning.
Patch is against 2.6.28-rc2 and depends on
http://marc.info/?l=linux-usb&m=122581634925308&w=2 (as submitted by
Alan Stern).
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1160b) adds support routines for asynchronous autosuspend
and autoresume, with accompanying documentation updates. There
already are several potential users of this interface, and others are
likely to arise as autosuspend support becomes more widespread.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1153) fixes a potential problem in hub initialization.
Starting in 2.6.28, initialization was split into several tasks to
help speed up booting. This opens the possibility that the hub may be
autosuspended before all the initialization tasks can complete.
Normally that wouldn't matter, but with incomplete initialization
there is a risk that the hub would never autoresume -- especially if
devices were plugged into the hub beforehand. The solution is a
simple one-line change to suppress autosuspend until the
initialization is finished.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1151) protects usbcore against drivers that try to
unlink an URB after the URB's device or bus have been removed. The
core does not currently check for this, and certain drivers can cause
a crash if they are running while an HCD is unloaded.
Certainly it would be best to fix the guilty drivers. But a little
defensive programming doesn't hurt, especially since it appears that
quite a few drivers need to be fixed.
The patch prevents the problem by grabbing a reference to the device
while an unlink is in progress and using a new spinlock to synchronize
unlinks with device removal. (There's no need to acquire a reference
to the bus as well, since the device structure itself keeps a
reference to the bus.) In addition, the kerneldoc is updated to
indicate that URBs should not be unlinked after the disconnect method
returns.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1152) may help prevent some problems associated with the
new policy of unbinding drivers that don't support suspend/resume or
pre_reset/post_reset. If for any reason the resume or reset fails, and
the device is logically disconnected, there's no point in trying to
rebind the driver. So the patch checks for success before carrying
out the unbind/rebind.
There was a report from one user that this fixed a problem he was
experiencing, but the details never became fully clear. In any case,
adding these tests can't hurt.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds initial_descriptor_timeout module parameter for usbcore.ko
to allow modify initial 64-byte USB_REQ_GET_DESCRIPTOR timeout for
non-standard devices.
For example, the SATA8000 device from DATAST0R Technology Corp
requires about 10 seconds to send reply (probably it waits until
inserted disk is ready for operation).
Also, this patch adds missing usbcore parameters to
Documentation/kernel-parameters.txt.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1137) changes the hub_activate() routine, replacing the
power-power-up and debounce delays with delayed_work calls. The idea
is that on systems where the USB stack is compiled into the kernel
rather than built as modules, these delays will no longer block the
boot thread. At least 100 ms is saved for each root hub, which can
add up to a significant savings in total boot time.
Arjan van de Ven was very pleased to see that this shaved 700 ms off
his computer's boot time. Since his total boot time is on the order
of two seconds, the improvement is considerable.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1135) essentially reverts the major parts of two earlier
patches to usbcore, because they ended up causing a regression.
Trying to recover from transient communication errors can lead to
other problems, because operations that failed during the error period
are not always retried. The simplest example is the initial
Set-Config request sent after device enumeration; if it gets lost then
it will not be retried and the device will remain unconfigured.
This patch restores the old behavior in which any port disconnect or
port disable causes the entire device structure to be removed, fixing a
reported regression.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1069c) changes the way OHCI root-hub status-change
interrupts are enabled. Currently a special HCD method,
hub_irq_enable(), is called when the hub driver is finished using a
root hub. This approach turns out to be subject to races, resulting
in unnecessary polling.
The patch does away with the method entirely. Instead, the driver
automatically enables the RHSC interrupt when no more status changes
are present. This scheme is safe with controllers using
level-triggered semantics for their interrupt flags.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1109b) makes USB-Persist more resilient to errors. With
the current code, if a normal resume fails, it's an unrecoverable
error. With the patch, if a normal resume fails (and if the device is
enabled for USB-Persist) then a reset-resume is tried.
This fixes the problem reported in Bugzilla #10977.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1024) takes care of a FIXME issue: Drivers that don't
have the necessary suspend, resume, reset_resume, pre_reset, or
post_reset methods will be unbound and their interface reprobed when
one of the unsupported events occurs.
This is made slightly more difficult by the fact that bind operations
won't work during a system sleep transition. So instead the code has
to defer the operation until the transition ends.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch renames the existing usb_reset_device in hub.c to
usb_reset_and_verify_device and renames the existing
usb_reset_composite_device to usb_reset_device. Also the new
usb_reset_and_verify_device does't need to be EXPORTED .
The idea of the patch is that external interface driver
should warn the other interfaces' driver of the same
device before and after reseting the usb device. One interface
driver shoud call _old_ usb_reset_composite_device instead of
_old_ usb_reset_device since it can't assume the device contains
only one interface. The _old_ usb_reset_composite_device
is safe for single interface device also. we rename the two
functions to make the change easily.
This patch is under guideline from Alan Stern.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
From the current implementation of usb_reset_composite_device
function, the iface parameter is no longer useful. This function
doesn't do something special for the iface usb_interface,compared
with other interfaces in the usb_device. So remove the parameter
and fix the related caller.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We can't allow hubs on the 7th tier as they would allow
devices on the 8th tier.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1083) combines hub_quiesce() and hub_stop() into a
single routine. There's no point keeping them separate since they are
usually called together.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1071) combines hub_activate() and hub_restart() into a
single routine. There's no point keeping them separate, since they
are always called together.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1082) makes a small optimization to the way the hub
driver carries out port debouncing immediately after a hub is
activated (i.e., initialized, reset, or resumed). If any port-change
statuses are observed, the code will delay for a minimal debounce
period -- thereby making a good start at debouncing all the ports at
once.
If this wasn't sufficient then khubd will debounce any port that still
requires attention. But in most cases it should suffice; it's rare
for a device to need more than a minimal debounce delay. (In the
cases of hub initialization or reset even that is most likely not
needed, since any devices plugged in at such times have probably been
attached for a while.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1073) adds to khubd a way to recover from power-session
interruption caused by transient connect-change or enable-change
events. After the debouncing period, khubd attempts to do a
USB-Persist-style reset or reset-resume. If it works, the connection
will remain unscathed.
The upshot is that we will be more immune to noise caused by EMI. The
grace period is on the order of 100 ms, so this won't permit recovery
from the "accidentally knocked the USB cable out of its socket" type
of event, but it's a start.
As an added bonus, if a device was suspended when the system goes to
sleep then we no longer need to check for power-session interruptions
when the system wakes up. Khubd will naturally see the status change
while processing the device's parent hub and will do the right thing.
The remote_wakeup() routine is changed; now it expects the caller to
acquire the device lock rather than acquiring the lock itself.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1081) straightens out the logic of the hub_restart()
routine. Each port of the hub is scanned and the driver makes sure
that ports which are supposed to be disabled really _are_ disabled.
Any ports with a significant change in status are flagged in
hub->change_bits, so that khubd can focus on them without the need to
scan all the ports a second time -- which means the hub->activating
flag is no longer needed.
Also, it is now recognized explicitly that the only reason for
resuming a port which was not suspended is to carry out a reset-resume
operation, which happens only in a non-CONFIG_USB_SUSPEND setting.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts Linus's previous patch that is in mainline to make it
easier for the USB hub.c patches that follow this to apply cleanly. The
functionality will be added back in a followon patch in this series.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1080) makes a significant change to the way khubd
handles port connect-change and enable-change events. Both types of
event are now debounced, and the debouncing is carried out _before_ an
existing usb_device is unregistered, instead of afterward.
This means that drivers will have to deal with longer runs of errors
when a device is unplugged, but they are supposed to be prepared for
that in any case.
The advantage is that when an enable-change occurs (caused for example
by electromagnetic interference), the debouncing period will provide
time for the cause of the problem to die away. A simple port reset
(added in a forthcoming patch) will then allow us to recover from the
fault.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1070) creates a new subroutine to check whether a device
can be resumed. This code is needed even when CONFIG_USB_SUSPEND
isn't set, because devices do suspend themselves when the root hub
(and hence the entire bus) is suspended, and power sessions can get
lost during a system sleep even without individual port suspends.
The patch also fixes a loose end in USB-Persist reset-resume handling.
When a low- or full-speed device is attached to an EHCI's companion
controller, the port handoff during resume will cause the companion
port's connect-status-change feature to be set. If that flag isn't
cleared, the port-reset code will think it indicates that the device
has been unplugged and the reset-resume will fail.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts Alan's previous patch so that the recent Hub changes will
apply cleanly. The above mentioned patch was needed for 2.6.26 to work
properly.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Lukas Hejtmanek <xhejtman@ics.muni.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit e872154921.
Andrey Borzenkov reports that it resulted in a totally hung machine for
him when loading the OHCI driver. Extensive netconsole capture with
SysRq output shows that modprobe gets stuck in ohci_hub_status_data()
when probing and enabling the OHCI controller, see for example
http://lkml.org/lkml/2008/7/5/236
for an analysis.
The problem appears to be an interrupt flood triggered by the commit
that gets reverted, and Andrey confirmed that the revert makes things
work for him again.
Reported-and-tested-by: Andrey Borzenkov <arvidjaar@mail.ru>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as1111) fixes a bug in the hub driver. When a hub
resumes, disconnections that occurred while the hub was suspended are
lost.
A completely different fix for this problem has already been accepted
for 2.6.27; however the problem still needs to be handled in 2.6.26.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Lukas Hejtmanek <xhejtman@ics.muni.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch tries to identify which devices are able to accept
reset-resume handling, by checking that there is at least one
interface driver bound and that all of the drivers have a reset_resume
method defined. If these conditions don't hold then during resume
processing, the device is logicall disconnected.
This is only a temporary fix. Later on we will explicitly unbind
drivers that can't handle reset-resumes.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Pavel Machek <pavel@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1096) fixes an annoying problem: When a full-speed or
low-speed device is plugged into an EHCI controller, it fails to
enumerate at high speed and then is handed over to the companion
controller. But usbcore logs a misleading and unwanted error message
when the high-speed enumeration fails.
The patch adds a new HCD method, port_handed_over, which asks whether
a port has been handed over to a companion controller. If it has, the
error message is suppressed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a potential deadlock when the usb_generic driver is unbound
from a device. The problem is that generic_disconnect() is called
with the device lock held, and it removes a bunch of device attributes
from sysfs. If a user task happens to be running an attribute method
at the time, the removal will block until the method returns. But at
least one of the attribute methods (the store routine for power/level)
needs to acquire the device lock!
This patch (as1093) eliminates the deadlock by moving the calls to
create and remove the sysfs attributes from the usb_generic driver
into usb_new_device() and usb_disconnect(), where they can be invoked
without holding the device lock.
Besides, the other sysfs attributes are created when the device is
registered and removed when the device is unregistered. So it seems
only fitting for the extra attributes to be created and removed at the
same time.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For WUSB devices, usb_dev.devnum is a device index and not the real
device address (which is managed by wusbcore). Therefore, only set
devnum once (in choose_address()) and never change it.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Cc: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need to be able to call ep0_reinit() [renamed to usb_ep0_reinit()]
from the WUSB security code. The reason is that when we authenticate
the device, it's address changes (from having bit 7 set to having it
cleared). Thus, we need to signal the USB stack to reinitialize EP0,
so the status with the previous address kept at the HCD layer is
cleared and properly reinitialized.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A WUSB device gets his address during the connection phase; later on,
during the authenthication phase (driven from user space) we assign
the final address. So we need to skip in hub_port_init() the actual
setting of the address for WUSB devices.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Modify choose_address() so it knows about our special scheme of
addressing WUSB devices (1:1 w/ port number).
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1069b) changes the way OHCI root-hub status-change
interrupts are enabled. Currently a special HCD method,
hub_irq_enable(), is called when the hub driver is finished using a
root hub. This approach turns out to be subject to races, resulting
in unnecessary polling.
The patch does away with the method entirely. Instead, the driver
automatically enables the RHSC interrupt when no more status changes
are present. This scheme is safe with controllers using
level-triggered semantics for their interrupt flags.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1077) logs an error message whenever the kernel is
unable to enumerate a new USB device.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1048) extends the descriptor checking after a device is
reset. Now the SerialNumber string descriptor is compared to its old
value, in addition to the device and configuration descriptors.
As a consequence, the kmalloc() call in usb_string() is now on the
error-handling pathway for usb-storage. Hence its allocation type is
changed to GFO_NOIO.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1047) removes the USB_PERSIST Kconfig option, enabling
it permanently. It also prevents the power/persist attribute from
being created for hub devices; there's no point in having it since
USB-PERSIST is always turned on for hubs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1046) makes USB-PERSIST work more in accordance with
the documentation. Currently it takes effect only in cases where the
root hub has lost power or been reset, but it is supposed to operate
whenever a power session was dropped during a system sleep.
A new hub_restart() routine carries out the duties required during a
reset or a reset-resume. It checks to see whether occupied ports are
still enabled, and if they aren't then it clears the enable-change and
connect-change features (to prevent interference by khubd) and sets
the child device's reset_resume flag. It also checks ports that are
supposed to be unoccupied to verify that the firmware hasn't left the
port in an enabled state.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1045) reorganizes some code in the hub driver.
hub_port_status() is moved earlier in the file, and a new hub_stop()
routine is created to do the work currently in hub_preset() (i.e.,
disconnect all child devices and quiesce the hub).
There are no functional changes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1044) causes EHCI port handover for non-high-speed
devices to occur during every root-hub resume, not just in cases where
the controller lost power or was reset. This is necessary because:
When some machines go into suspend, they remove power from
on-board USB devices while retaining suspend current for USB
controllers.
The user might well unplug a USB device while the system is
suspended and then plug it back in before resuming.
A corresponding change is made to the core resume routine; now
high-speed root hubs will always be resumed when the system wakes up,
even if they were suspended before the system went to sleep. If this
weren't done then EHCI port handover wouldn't work, since it is called
when the EHCI root hub is resumed.
Finally, a comment is added to the hub driver explaining the khubd has
to be freezable; if it weren't frozen then it could interfere with
port handover.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
None of these files use any of the functionality promised by
asm/semaphore.h. It's possible that they rely on it dragging in some
unrelated header file, but I can't build all these files, so we'll have
fix any build failures as they come up.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Over two years ago, the Linux USB developers stated that they believed
there was no way to create a USB kernel driver that was not under the
GPL. This patch moves the USB apis to enforce that decision.
There are no known closed source USB drivers in the wild, so this patch
should cause no problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch exports two statistics to userspace:
/sys/bus/usb/device/.../power/connected_duration
/sys/bus/usb/device/.../power/active_duration
connected_duration is the total time (in msec) that the device has
been connected. active_duration is the total time the device has not
been suspended. With these two statistics, tools like PowerTOP can
calculate the percentage time that a device is active, i.e. not
suspended or auto-suspended.
Users can also use the active_duration to check if a device is actually
autosuspended. Currently, they can set power/level to auto and
power/autosuspend to a positive timeout, but there's no way to know from
userspace if a device was actually autosuspended without looking at the
dmesg output. These statistics will be useful in creating an automated
userspace script to test autosuspend for USB devices.
Signed-off-by: Sarah Sharp <sarah.a.sharp@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1023) updates the code in usb_reset_composite_device():
Some local variable declarations are moved to inner loops.
The interface locks are not acquired. This isn't necessary
any more; its only reason was to prevent an interface from
being suspended or resumed during the reset. But now
interface power management is controlled by the USB device
lock, not by the interface lock.
The check for whether the interface is registered is removed.
There doesn't seem to be any reason for checking; a driver
for a non-registered interface deserves to be informed of
device resets just as much as any other.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Distros (like SuSE) want to know this information, to make it easier
to handle support issues. Might as well let everyone benefit from this.
This is also enabled whenever CONFIG_USB_DEBUG is enabled, to help with
debugging.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch hands over the port to the companion when the
hub_port_connect_change fails.
Signed-off-by: Balaji Rao <balajirrao@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this function will run in the context of the scsi error handler thread.
It must use GFP_NOIO instead of GFP_KERNEL to avoid a possible
deadlock.
Cc: stable <stable@kernel.org>
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1027) replaces a call to flush_scheduled_work() -- a
dangerous routine to invoke, especially while holding any sort of lock
-- with calls to cancel_work_sync() and cancel_delayed_work_sync().
This fixes Bugzilla #9532.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Introduce freezer-friendly wrappers around wait_event_interruptible() and
wait_event_interruptible_timeout(), originally defined in <linux/wait.h>, to
be used in freezable kernel threads. Make some of the freezable kernel
threads use them.
This is necessary for the freezer to stop sending signals to kernel threads,
which is implemented in the next patch.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@nigel.suspend2.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix USB docbook warnings.
Warning(linux-2.6.23-git8//include/linux/usb/gadget.h:487): No description found for parameter 'g'
Warning(linux-2.6.23-git8//include/linux/usb/gadget.h:506): No description found for parameter 'g'
Warning(linux-2.6.23-git8//drivers/usb/core/hub.c:1416): No description found for parameter 'usb_dev'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as999) fixes a problem that sometimes shows up when host
controller driver modules are loaded in the wrong order. If ehci-hcd
happens to initialize an EHCI controller while the companion OHCI or
UHCI controller is in the middle of a port reset, the reset can fail
and the companion may get very confused. The patch adds an
rw-semaphore and uses it to keep EHCI initialization and port resets
mutually exclusive.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: David Miller <davem@davemloft.net>
Cc: Dely L Sy <dely.l.sy@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (jx001) fixes a variable assignment mistake in hub driver.
limited_power should be set to 0 if the hub is self-powered,and 1 if
the hub is bus-powered.
However, the effect of the code was exactly opposite to the spec's
statement for the Local Power Source field. The spec says, this field
is 1 meaning Local power supply lost while this field is 0 indicating
Local power supply good.(This statement is very confusing.)
So this patch switchs the 0 and 1.
Signed-off-by: Jason Xiao <jidong.xiao@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as989) makes usbcore flush all outstanding URBs for each
device as the device is suspended. This will be true even when
CONFIG_USB_SUSPEND is not enabled.
In addition, an extra can_submit flag is added to the usb_device
structure. That flag will be turned off whenever a suspend request
has been received for the device, even if the device isn't actually
suspended because CONFIG_USB_SUSPEND isn't set.
It's no longer necessary to check for the device state being equal to
USB_STATE_SUSPENDED during URB submission; that check can be replaced
by a check of the can_submit flag. This also permits us to remove
some questionable references to the deprecated power.power_state field.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as981) removes the remaining nontrivial usages of
urb->status from usbcore.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As it is global, give it a usb specific name in the global namespace.
Cc: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These USB API functions will do the full authorization/deauthorization
to be used for a device. When authorized we effectively allow a
configuration to be set. Reverse that when deauthorized.
Effectively this means that we have to clean all the configuration
descriptors on deauthorize and reload them when we authorized. We could
do without throwing them out for wired devices, but for wireless, we can
read them only after authenticating, and thus, when authorizing an
authenticated device we would need to read them. So to simplify, always
release them on deauthorize(), re-read them on authorize().
Also fix leak reported by Ragner Magalhaes; in usb_deauthorize_device(),
bNumConfigurations was being set to zero before the for loop, and thus
the different raw descriptors where never being freed.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch takes hub.c:usb_new_device() and splits it in three parts:
- The actual actions of adding a new device (quirk detection,
announcement and autoresume tracking)
- Actual discovery and probing of the configuration and interfaces
(split into __usb_configure_device())
- Configuration of the On-the-go parameters (split into
__usb_configure_device_otg()).
The fundamental reasons for doing this split are clarity (smaller
functions are easier to maintain) and to allow part of the code to be
reused when authorizing devices to connect.
When a device is authorized connection, we need to run through the
hoops we didn't run when it was connected but not authorized, which is
basically parsing the configurations and probing
them. usb_configure_device() will do that for us.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as947) changes the device initialization and enumeration
code in hub.c; now udev->devnum will be set to 0 while the device is
being accessed at address 0. Until now this wasn't needed because the
address value was passed as part of urb->pipe; without that field the
device address must be stored elsewhere.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as944) adds an explicit "enabled" field to the
usb_host_endpoint structure and uses it in place of the current
mechanism. This is merely a time-space tradeoff; it makes checking
whether URBs may be submitted to an endpoint simpler. The existing
mechanism is efficient when converting urb->pipe to an endpoint
pointer, but it's not so efficient when urb->ep is used instead.
As a side effect, the procedure for enabling an endpoint is now a
little more complicated. The ad-hoc inline code in usb.c and hub.c
for enabling ep0 is now replaced with calls to usb_enable_endpoint,
which is no longer static.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some devices have a bug which causes them to send a 1-byte reply to
Get-Device-Status requests instead of 2 bytes as required by the
spec. This doesn't play well with autosuspend, since we look for a
valid status reply to make sure the device is still present when it
resumes. Without both bytes, we assume the device has been
disconnected.
Lack of the second byte shouldn't matter much, since the spec requires
it always to be equal to 0. Hence this patch (as959) causes
finish_port_resume() to accept a 1-byte reply as valid.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as937) fixes a minor bug in the autosuspend usage-counting
code. Each hub's usage counter keeps track of the number of
unsuspended children. However the current driver increments the
counter after registering a new child, by which time the child may
already have been suspended and caused the counter to go negative.
The obvious solution is to increment the counter before registering
the child.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, the freezer treats all tasks as freezable, except for the kernel
threads that explicitly set the PF_NOFREEZE flag for themselves. This
approach is problematic, since it requires every kernel thread to either
set PF_NOFREEZE explicitly, or call try_to_freeze(), even if it doesn't
care for the freezing of tasks at all.
It seems better to only require the kernel threads that want to or need to
be frozen to use some freezer-related code and to remove any
freezer-related code from the other (nonfreezable) kernel threads, which is
done in this patch.
The patch causes all kernel threads to be nonfreezable by default (ie. to
have PF_NOFREEZE set by default) and introduces the set_freezable()
function that should be called by the freezable kernel threads in order to
unset PF_NOFREEZE. It also makes all of the currently freezable kernel
threads call set_freezable(), so it shouldn't cause any (intentional)
change of behaviour to appear. Additionally, it updates documentation to
describe the freezing of tasks more accurately.
[akpm@linux-foundation.org: build fixes]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as920) adds an extra level of protection to the
USB-Persist facility. Now it will apply by default only to hubs; for
all other devices the user must enable it explicitly by setting the
power/persist device attribute.
The disconnect_all_children() routine in hub.c has been removed and
its code placed inline. This is the way it was originally as part of
hub_pre_reset(); the revised usage in hub_reset_resume() is
sufficiently different that the code can no longer be shared.
Likewise, mark_children_for_reset() is now inline as part of
hub_reset_resume(). The end result looks much cleaner than before.
The sysfs interface is updated to add the new attribute file, and
there are corresponding documentation updates.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as919) unifies the code paths used for normal resume and
for reset-resume. Earlier I had failed to note a section in the USB
spec which requires the host to resume a suspended port before
resetting it if the attached device is enabled for remote wakeup.
Since the port has to be resumed anyway, we might as well reuse the
existing code.
The main changes are:
usb_reset_suspended_device() is eliminated.
usb_root_hub_lost_power() is moved down next to the
hub_reset_resume() routine, to which it is logically
related.
finish_port_resume() does a port reset() if the device's
reset_resume flag is set.
usb_port_resume() doesn't check whether the port is initially
enabled if this is a USB-Persist sort of resume.
Code to perform the port reset is added to the resume pathway
for the non-CONFIG_USB_SUSPEND case.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as918) introduces a new USB driver method: reset_resume.
It is called when a device needs to be reset as part of a resume
procedure (whether because of a device quirk or because of the
USB-Persist facility), thereby taking over a role formerly assigned to
the post_reset method. As a consequence, post_reset no longer needs
an argument indicating whether it is being called as part of a
reset-resume. This separation of functions makes the code clearer.
In addition, the pre_reset and post_reset method return types are
changed; they now must return an error code. The return value is
unused at present, but at some later time we may unbind drivers and
re-probe if they encounter an error during reset handling.
The existing pre_reset and post_reset methods in the usbhid,
usb-storage, and hub drivers are updated to match the new
requirements. For usbhid the post_reset routine is also used for
reset_resume (duplicate method pointers); for the other drivers a new
reset_resume routine is added. The change to hub.c looks bigger than
it really is, because mark_children_for_reset_resume() gets moved down
next to the new hub_reset_resume() routine.
A minor change to usb-storage makes the usb_stor_report_bus_reset()
routine acquire the host lock instead of requiring the caller to hold
it already.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as917) removes a now-unnecessary level of subroutine
nesting from hub.c. Since usb_port_suspend() does nothing but call
hub_port_suspend(), and usb_port_resume() does nothing but call
hub_port_resume(), there's no reason to keep the routines separate.
Also included in the patch are a few cosmetic changes involving
whitespace and use of braces.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as916) completes the separation of code paths for suspend
and resume of root hubs as opposed to non-root devices. Root hubs
will be power-managed through their bus_suspend and bus_resume
methods, whereas normal devices will use usb_port_suspend() and
usb_port_resume().
Changes to the hcd_bus_{suspend,resume} routines mostly represent
motion of code that was already present elsewhere. They include:
Adding debugging log messages,
Setting the device state appropriately, and
Adding a resume recovery time delay.
Changes to the port-suspend and port-resume routines in hub.c include:
Removal of checks for root devices (since they will never
be triggered), and
Removal of checks for NULL or invalid device pointers (these
were left over from earlier kernel versions and aren't needed
at all).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as915b) combines the public routine usb_port_suspend() and
the private routine __usb_port_suspend() into a single function.
By removing the explicit mention of otg_port in the call to
__usb_port_suspend(), we prevent a possible error in which the system
tries to perform HNP on the wrong port when a non-targeted device is
plugged into a non-OTG port.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch is to prevent the OTG host of doing 3 times enumeration of
device when the Host suspends for HNP. The error code used in
this case is ENOTSUPP.
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Okay, found it. The root cause here was a missing CONFIG_USB_SUSPEND=y,
which means the hci_usb device never got marked as USB_STATE_SUSPENDED,
which then caused the loop to go on forever.
The system works fine now with CONFIG_USB_SUSPEND=y in the .config.
Here's the patch to prevent future lockups for this or other causes.
I no longer need it, but it does still seem a good idea.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as898) changes the port reset code in the hub driver. If
a connect change occurs, it is reported the same way as a disconnect
(which of course is what it really is).
It also changes usb_reset_device(), to prevent the routine from futilely
retrying the reset after a disconnect has occurred.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as888) adds a new USB device quirk for devices which are
unable to resume correctly. By using the new code added for the
USB-persist facility, it is a simple matter to reset these devices
instead of resuming them. To get things kicked off, a quirk entry is
added for the Philips PSC805.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as886) adds the controversial USB-persist facility,
allowing USB devices to persist across a power loss during system
suspend.
The facility is controlled by a new Kconfig option (with appropriate
warnings about the potential dangers); when the option is off the
behavior will remain the same as it is now. But when the option is
on, people will be able to use suspend-to-disk and keep their USB
filesystems intact -- something particularly valuable for small
machines where the root filesystem is on a USB device!
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This revised patch (as893c) improves the method used by the hub driver
to release its private data structure. The current code is non-robust,
relying on a memory region not getting reused by another driver after
it has been freed. The patch adds a reference count to the structure,
resolving the question of when to release it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as892) removes the "locktree" routine from the hub driver.
It currently is used in only one place, by a single kernel thread;
hence it isn't doing any good.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as889) prevents the hub driver from trying to resume a
port when there is a new connection. For one thing, the resume is not
needed -- the upcoming port reset will clear the suspend feature
automatically. For another, on some systems the resume fails and
causes problems.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as885) moves the root-hub bus_suspend() and bus_resume()
method calls from the hub driver's suspend and resume methods into the
usb_generic driver methods, where they make just as much sense.
Their old locations were not fully correct. For example, in a kernel
compiled without CONFIG_USB_SUSPEND, if one were to do:
echo -n 1-0:1.0 >/sys/bus/usb/drivers/hub/unbind
to unbind the hub driver from a root hub, there would then be no way
to suspend that root hub. Attempts to put the system to sleep would
fail; the USB controller driver would refuse to suspend because the
root hub was still active.
The patch also makes a very slight change in the way devices with no
driver are handled during suspend. Rather than doing a standard USB
port-suspend directly, now the suspend routine in usb_generic is
called. In practice this should never affect anyone.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The prev_state member of struct dev_pm_info (defined in include/linux/pm.h) is
only used during a resume to check if the device's state before the suspend was
'off', in which case the device is not resumed. However, in such cases the
decision whether or not to resume the device should be made on the driver level
and the resume callbacks from the device's bus and class should be executed
anyway (the may be needed for some things other than just powering on the
device).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as912) replaces a couple of calls to flush_workqueue()
with cancel_sync_work() and cancel_rearming_delayed_work(). Using a
more directed approach allows us to avoid some nasty deadlocks. The
prime example occurs when a first-level device (the parent is a root
hub) is removed while at the same time the root hub gets a remote
wakeup request. khubd would try to flush the autosuspend workqueue
while holding the root-hub's lock, and the remote-wakeup workqueue
routine would be waiting to lock the root hub.
The patch also reorganizes the power management portion of
usb_disconnect(), separating it out into its own routine. The
autosuspend workqueue entry is cancelled immediately instead of
waiting for the device's release routine. In addition,
synchronization with the autosuspend thread is carried out even for
root hubs (an oversight in the original code).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg KH <gregkh@suse.de>
Cc: Mark Lord <lkml@rtr.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as910) fixes a ratelimit modification so that the
original error-handling path will be followed even when the log-rate
limitation kicks in.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as905) removes a micro-optimization from the hub port
initialization code. Previously we had been using a short timeout on
the first attempt the read the device descriptor; now we will use the
standard timeout length.
It's not clear that the short timeout ever provided any benefit. And
now we know of one case where it actually hurts: The device can't meet
the short timeout and then it gets terminally confused.
This fixes Bugzilla #8444.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove includes of <linux/smp_lock.h> where it is not used/needed.
Suggested by Al Viro.
Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc,
sparc64, and arm (all 59 defconfigs).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as877) adds a "last_busy" field to struct usb_device, for
use by the autosuspend framework. Now if an autosuspend call comes at
a time when the device isn't busy but hasn't yet been idle for long
enough, the timer can be set to exactly the desired value. And we
will be ready to handle things like HID drivers, which can't maintain
a useful usage count and must rely on the time-of-last-use to decide
when to autosuspend.
The patch also makes some related minor improvements:
Move the calls to the autosuspend condition-checking routine
into usb_suspend_both(), which is the only place where it
really matters.
If the autosuspend timer is already running, don't stop
and restart it.
Replace immediate returns with gotos so that the optional
debugging ouput won't be bypassed.
If autoresume is disabled but the device is already awake,
don't return an error for an autoresume call.
Don't try to autoresume a device if it isn't suspended.
(Yes, this undercuts the previous change -- so sue me.)
Don't duplicate existing code in the autosuspend work routine.
Fix the kerneldoc in usb_autopm_put_interface(): If an
autoresume call fails, the usage counter is left unchanged.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
o The "real" usb-devices export now a device node which can
populate /dev/bus/usb.
o The usb_device class is optional now and can be disabled in the
kernel config. Major/minor of the "real" devices and class devices
are the same.
o The environment of the usb-device event contains DEVNUM and BUSNUM to
help udev and get rid of the ugly udev rule we need for the class
devices.
o The usb-devices and usb-interfaces share the same bus, so I used
the new "struct device_type" to let these devices identify
themselves. This also removes the current logic of using a magic
platform-pointer.
The name of the device_type is also added to the environment
which makes it easier to distinguish the different kinds of devices
on the same subsystem.
It looks like this:
add@/devices/pci0000:00/0000:00:1d.1/usb2/2-1
ACTION=add
DEVPATH=/devices/pci0000:00/0000:00:1d.1/usb2/2-1
SUBSYSTEM=usb
SEQNUM=1533
MAJOR=189
MINOR=131
DEVTYPE=usb_device
PRODUCT=46d/c03e/2000
TYPE=0/0/0
BUSNUM=002
DEVNUM=004
This udev rule works as a replacement for usb_device class devices:
SUBSYSTEM=="usb", ACTION=="add", ENV{DEVTYPE}=="usb_device", \
NAME="bus/usb/$env{BUSNUM}/$env{DEVNUM}", MODE="0644"
Updated patch, which needs the device_type patches in Greg's tree.
I also got a bugzilla assigned for this. :)
https://bugzilla.novell.com/show_bug.cgi?id=250659
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as866) adds new entry points for external USB device
suspend and resume requests, as opposed to internally-generated
autosuspend or autoresume. It also changes the existing
remote-wakeup code paths to use the new routines, since remote wakeup
is not the same as autoresume.
As part of the change, it turns out to be necessary to do remote
wakeup of root hubs from a workqueue. We had been using khubd, but it
does autoresume rather than an external resume. Using the
ksuspend_usb_wq workqueue for this purpose seemed a logical choice.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Duplicate what Zach Brown did for pr_debug in commit
8b2a1fd1b3
[akpm@linux-foundation.org: fix a couple of things which broke]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
flaky hardware can cause a lot of debounce failed messages. To limit
the performance impact, a ratelimit should be used.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds a blacklist to the USB core to handle some autosuspend and
string issues that devices have.
Originally written by Oliver, but hacked up a lot by Greg.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as849) fixes a bug in the USB hub driver. A single
pre-allocated buffer is used for all port status reads, but nothing
guarantees exclusive use of the buffer. A mutex is added to provide
this guarantee.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as847) makes some small changes to the hub driver's
suspend method:
For root hubs, the status URB should be unlinked and other
activity stopped _before_ the bus_suspend method is called.
The test for hdev->bus being NULL has been removed, since
it can never succeed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The whole approach is simply wrong. Forking a thread means that
- errors are ignored
- locking is ignored
Doing this correctly would require major surgery for questionable benefit.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Disable the USB_MULTITHREAD_PROBE option because it causes crashes on
people's machines and they never remember to actually read the config
help files.
No one likes this, everyone hates it, I'm going to go eat worms...
The full logic will be ripped out later.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move process freezing functions from include/linux/sched.h to freezer.h, so
that modifications to the freezer or the kernel configuration don't require
recompiling just about everything.
[akpm@osdl.org: fix ueagle driver]
Signed-off-by: Nigel Cunningham <nigel@suspend2.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_KERNEL is an alias of GFP_KERNEL.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_ATOMIC is an alias of GFP_ATOMIC
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix up arch-specific work items where possible to use the new work_struct and
delayed_work structs.
Three places that enqueue bits of their stack and then return have been marked
with #error as this is not permitted.
Signed-Off-By: David Howells <dhowells@redhat.com>
Conflicts:
drivers/infiniband/core/iwcm.c
drivers/net/chelsio/cxgb2.c
drivers/net/wireless/bcm43xx/bcm43xx_main.c
drivers/net/wireless/prism54/islpci_eth.c
drivers/usb/core/hub.h
drivers/usb/input/hid-core.c
net/core/netpoll.c
Fix up merge failures with Linus's head and fix new compilation failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
Thanks to several earlier patches, usb_autosuspend_device() and
usb_autoresume_device() are never called with a second argument other
than 1. This patch (as819) removes the now-redundant argument.
It also consolidates some common code between those two routines,
putting it into a new subroutine called usb_autopm_do_device(). And
it includes a sizable kerneldoc update for the affected functions.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as818b) simplifies autosuspend processing by keeping track
of the number of unsuspended children of each USB hub. This will
permit us to avoid a good deal of unnecessary work all the time; we
will no longer have to create a bunch of workqueue entries to carry
out autosuspend requests, only to have them fail because one of the
hub's children isn't suspended.
The basic idea is simple. There already is a usage counter in the
usb_device structure for preventing autosuspends. The patch just
increments that counter for every unsuspended child. There's only one
tricky part: When a device disconnects we need to remember whether it
was suspended at the time (leave the counter alone) or not (decrement
the counter).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as817) simplifies the remote-wakeup processing in the hub
driver. Now instead of using a specialized code path, it relies on
the standard USB resume routines. The hub_port_resume() function does
an initial get_port_status() to see whether the port has already
resumed itself (as it does when a remote-wakeup request is sent).
This will slow down handling of other resume events slightly, but not
enough to matter.
The patch also changes the hub_port_status() routine, making it return
an error if a short reply is received.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as742b) adds autosuspend/autoresume support to the USB hub
driver. The largest aspect of the change is that we no longer need a
special flag for root hubs that want to be resumed. Now every hub is
autoresumed whenever khubd needs to access it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Might speed up some systems. If nothing else, a bad driver should not
take the whole USB subsystem down with it.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as809b) moves the declaration of the hub driver's private
data structure from hub.h into the hub.c source file. Lots of other
files import hub.h; they have no need to know about the details of the
hub driver's private data.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Wireless USB Host Controllers accept a large number of devices per
host, which shows up as a large number of ports in its root hub.
When the number of ports in a hub device goes over 16, the activation
of the hub fails with the cryptic message in klogd.
hub 2-0:1.0: activate --> -22
Following this further, it was seen that:
hub_probe()
hub_configure()
generates pipe number
pseudo allocates buffer 'maxp' bytes in size using usb_maxpacket()
The endpoint descriptor for a root hub interrupt endpoint is
declared in
drivers/usb/core/hcd.c:hs_rh_config_descriptor and declares it
to be size two (supporting 15 devices max).
hub_activate()
usb_hcd_submit_urb()
rh_urb_enqueue()
urb->pipe is neither int nor ctl, so it errors out
rh_queue_status()
Returns -EINVAL because the buffer length is smaller
than the minimum needed to report all the hub port
bits as in accordance with USB2.0[11.12.3]. There has
to be trunc((PORTS + 1 + 7) / 8) bytes of space at
least.
Alan Stern confirmed that the reason for reading maxpktsize and not
the right amount is because some hubs are known to return more data
and thus cause overflow.
So this patch simply changes the code to make the interrupt endpoint's
max packet size be at least the minimum required by USB_MAXCHILDREN
(instead of a fixed magic number) and add documentation for that. This
way we are always ahead of the limit.
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove complaint from newer GCCs; they don't like forward function
declarations except in top-level contexts.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
This patch (as791b) fixes things up to avoid compiler warnings or
errors when CONFIG_USB_SUSPEND or CONFIG_PM isn't set.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Somewhere along the line, a variable in a USB-OTG codepath
stopped being used; this removes the relevant compiler warning.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch(as785) forces the PM core to resume a root hub after a
power loss during system sleep. If the root hub had been suspended
before the system sleep then normally the PM core would not resume it
afterward. Without this resume, various sorts of wakeup events (like
port change events) can get lost.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch removes unneeded casts for the following (void *) pointers:
- struct file: private
- struct urb: context
- struct usb_bus: hcpriv
- return value of kmalloc()
The patch also contains some whitespace cleanup in the relevant areas.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as740) removes the existing support for autosuspend of
root hubs. That support fit in rather awkwardly with the rest of
usbcore and it was used only by ohci-hcd. It won't be needed any more
since the hub driver will take care of autosuspending all hubs, root
or external.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as739) adds the basic infrastructure for USB autosuspend
and autoresume. The main features are:
PM usage counters added to struct usb_device and struct
usb_interface, indicating whether it's okay to autosuspend
them or they are currently in use.
Flag added to usb_device indicating whether the current
suspend/resume operation originated from outside or as an
autosuspend/autoresume.
Flag added to usb_driver indicating whether the driver
supports autosuspend. If not, no device bound to the driver
will be autosuspended.
Mutex added to usb_device for protecting PM operations.
Unlike the device semaphore, the locking rule for the pm_mutex
is that you must acquire the locks going _up_ the device tree.
New routines handling autosuspend/autoresume requests for
interfaces and devices.
Suspend and resume requests are propagated up the device tree
(but not outside the USB subsystem).
work_struct added to usb_device, for carrying out delayed
autosuspend requests.
Autoresume added (and autosuspend prevented) during probe and
disconnect.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as778) adds a field to struct usb_device to store the
device's level in the USB tree. In itself this number isn't really
important. But the overhead is very low, and in a later patch it will
be used for preventing bogus warnings from the lockdep checker.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
New code being pushed to linuxuwb.org requires this patch to connect
WUSB devices.
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch teaches the USB stack handling of WUSB devices (those whose
speed is USB_SPEED_VARIABLE). For these devices, we need to set ep0's
maxpacketsize to 512 (even though the device descriptor reports it as
0xff).
New code being pushed to linuxuwb.org requires this patch to connect WUSB
devices.
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch enables the USB stack to recognize WUSB devices (from a
WUSB HCD) and assigns them the proper speed setting
(USB_SPEED_VARIABLE).
1. Introduce usb_hcd->wireless to mark a host controller instance as
being wireless, and thus having wireless 'fake' ports.
[discarded previous model of using a reserved bit in the port_stat
struct to do this; thanks to Alan Stern for indicating the
proper way to do it].
2. Introduce hub.c:hub_is_wusb() that tests if a hub is a WUSB root
hub (WUSB doesn't have non-root hubs).
New code being pushed to linuxuwb.org requires this patch to connect WUSB
devices.
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't want khubd to start interfering in the device-resume process
merely because the PORT_STATUS_C_SUSPEND feature happens to be set.
Ports need to be marked as busy while a resume is taking place.
In addition, so long as ports are marked as busy, khubd won't be able to
clear their various status-change features. On an interrupt-driven root
hub this could lead to an interrupt storm. Root hub IRQs should not be
re-enabled until the busy_bits value is equal to 0.
This patch (as765) fixes these two potential problems.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as736) makes the hub driver more readable by improving the
usage of "#ifdef CONFIG_PM" and "#ifdef CONFIG_USB_SUSPEND".
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as734) rationalizes the various tests of device state and
power states. There are duplications and mistaken tests in several
places.
Perhaps the most interesting challenge is where the hub driver tests to
see that all the child devices are suspended before allowing itself to
be suspended. When CONFIG_USB_SUSPEND is set the test is
straightforward, since we expect that the children _will_ be suspended.
But when CONFIG_USB_SUSPEND isn't set, it's not so clear what should be
done. The code compromises by checking the child's
power.power_state.event field.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as733) fixes up the places where device states and power
states are set in usbcore. Right now things are duplicated or missing;
this should straighten things out.
The idea is that udev->state is USB_STATE_SUSPENDED exactly when the
device's upstream port has been suspended, whereas
udev->dev.power.power_state.event reflects the result of the last call
to the suspend/resume routines (which might not actually change the
device state, especially if CONFIG_USB_SUSPEND isn't set).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as717b) removes the existing recursion in hub resume code:
Resuming a hub will no longer automatically resume the devices attached
to the hub.
At the same time, it adds one level of recursion: Suspending a USB
device will automatically suspend all the device's interfaces. Failure
at an intermediate stage will cause all the already-suspended interfaces
to be resumed. Attempts to suspend or resume an interface by itself will
do nothing, although they won't return an error. Thus the regular
system-suspend and system-resume procedures should continue to work as
before; only runtime PM will be affected.
The patch also removes the code that tests state of the interfaces
before suspending a device. It's no longer needed, since everything
gets suspended together.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as714b) makes usb_generic into a usb_device_driver capable
of being probed and unbound, just like other drivers. A fair amount of
the work that used to get done during discovery or removal of a USB
device have been moved to the probe and disconnect methods of
usb_generic: creating the sysfs attributes and selecting an initial
configuration. However the normal behavior should continue to be the
same as before.
We will now have the possibility of creating other USB device drivers,
They will assist with exporting devices to remote systems
(USB-over-TCPIP) or to paravirtual guest operating systems.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This revised patch (as715b) renames usb_suspend_device to
usb_port_suspend, usb_resume_device to usb_port_resume, and
finish_device_resume to finish_port_resume. There was no objection to
the original version of the patch so this should be okay to apply.
The revision was needed only because I have re-arranged the order of the
earlier patches.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as731) makes a couple of small fixes to the hub_port_resume
routine:
Don't return status >= 0 when an error occurs;
Clear the port-change-suspend status indicator after
resuming a device.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
finish_device_resume() in the hub driver isn't careful always to return
a negative code in all the error pathways. It also doesn't return 0 in
all the success pathways. This patch (as724) fixes the behavior.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as700) modifies the hub driver to take advantage of the new
usb_reset_composite_device API. The existing code had special-case
calls stuck into usb_reset_device, just before and after the reset.
With the new version there's no need for special-case stuff; it all
happens naturally in the form of pre_reset and post_reset notifications.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as699) adds usb_reset_composite_device(), a routine for
sending a USB port reset to a device with multiple interfaces owned by
different drivers. Drivers are notified about impending and completed
resets through two new methods in the usb_driver structure.
The patch modifieds the usbfs ioctl code to make it use the new routine
instead of usb_reset_device(). Follow-up patches will modify the hub,
usb-storage, and usbhid drivers so they can utilize this new API.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
RNDIS devices don't get configured owing to a typo in
choose_configuration(). This patch from Giridhar Pemmasani fixes the
typo.
From: Giridhar Pemmasani <giri@lmc.cs.sunysb.edu>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2.6.16 introduces USB power budgeting in the Linux kernel, and since then, a
fair number of users have observed that some of their devices no longer work in
unpowered hubs (this is not a bug, the devices claim that they need more than
100mA).
The very least we can do is print an informational message to the kernel log
when this happens, otherwise it is not at all clear why the device was not
accepted.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some hubs claim not to support port-power switching, and right now the
hub driver believes them and does not enable power to their ports.
However it turns out that even though they don't actually switch power,
they do ignore all events on a port until told to turn on the power!
This problem has been reported by several users.
This revised patch (as672b) makes the hub driver always try to turn on
port power to all hubs, regardless of what the hub descriptor says. It
also adds a comment explaining the need for this.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The choose_configuration() routine contains code the determine the
device's power source, so that configurations requiring external power
can be ruled out if the device is running on bus power. Unfortunately
it turns out that some devices have errors in their config descriptors
and other devices don't like the GET_DEVICE_STATUS request.
Since that information wasn't used for anything else, this patch (as673)
removes the code, leaving only a comment. It fixes bugzilla entry
#6448.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB OTG devices are not required to support external hubs. This adds a
configuration option to disable that support.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In a couple of places, usbcore assumes that a USB device configuration
will have a nonzero number of interfaces. Having no interfaces may or
may not be allowed by the USB spec; in any event we shouldn't die if we
encounter such a thing. This patch (as662) removes the assumptions.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as647) fixes a small error introduced by a recent change to
the USB core suspend/resume code.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This makes usbcore use the driver model wakeup flags for host controllers
and for their root hubs. Since previous patches have removed all users of
the HCD flags they replace, this converts the last users of those flags.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the patch below converts a bunch of semaphores-used-as-mutex in the USB
code to mutexes
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as614) makes a small change to the part of the hub driver
responsible for remote wakeup of root hubs. When these wakeups occur
the driver is suspended, and in case the resume fails the driver should
remain suspended -- it shouldn't try to proceed with its normal
processing.
This will hardly ever matter in normal use, but it did crop up while I
was debugging a different problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as610) adds a field to struct usb_device to store the device's
port number. This allows us to remove several loops in the hub driver
(searching for a particular device among all the entries in the parent's
array of children).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as609) changes the way we keep track of power budgeting for
USB hubs and devices, and it updates the choose_configuration routine to
take this information into account. (This is something we should have
been doing all along.) A new field in struct usb_device holds the amount
of bus current available from the upstream port, and the usb_hub structure
keeps track of the current available for each downstream port.
Two new rules for configuration selection are added:
Don't select a self-powered configuration when only bus power
is available.
Don't select a configuration requiring more bus power than is
available.
However the first rule is #if-ed out, because I found that the internal
hub in my HP USB keyboard claims that its only configuration is
self-powered. The rule would prevent the configuration from being chosen,
leaving the hub & keyboard unconfigured. Since similar descriptor errors
may turn out to be fairly common, it seemed wise not to include a rule
that would break automatic configuration unnecessarily for such devices.
The second rule may also trigger unnecessarily, although this should be
less common. More likely it will annoy people by sometimes failing to
accept configurations that should never have been chosen in the first
place.
The patch also changes usbcore's reaction when no configuration is
suitable. Instead of raising an error and rejecting the device, now
the core will simply leave the device unconfigured. People can always
work around such problems by installing configurations manually through
sysfs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The earlier USB locking updates didn't touch the suspend/resume
routines. They need updating as well, since now the caller holds the
device semaphore. This patch (as608) makes the necessary changes. It
also adds a line to store the correct power state when a device is
resumed, something which was unaccountably missing.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as606b) is an updated version of my earlier patch to
disconnect children from a hub device when the hub driver is unbound.
Thanks to the changes in the driver core locking, we now know that the
entire hub device (and not just the interface) is locked whenever the
hub driver's disconnect method runs. Hence it is safe to disconnect the
child device structures immediately instead of deferring the job.
The earlier version of the patch neglected to disable the hub's ports.
We don't want to forget that; otherwise we'd end up with live devices
using addresses that have been recycled. This update adds the necessary
code.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as605) removes the private udev->serialize semaphore,
relying instead on the locking provided by the embedded struct device's
semaphore. The changes are confined to the core, except that the
usb_trylock_device routine now uses the return convention of
down_trylock rather than down_read_trylock (they return opposite values
for no good reason).
A couple of other associated changes are included as well:
Now that we aren't concerned about HCDs that avoid using the
hcd glue layer, usb_disconnect no longer needs to acquire the
usb_bus_lock -- that can be done by usb_remove_hcd where it
belongs.
Devices aren't locked over the same scope of code in
usb_new_device and hub_port_connect_change as they used to be.
This shouldn't cause any trouble.
Along with the preceding driver core patch, this needs a lot of testing.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Andi Kleen