Merge reason: tracing/core was on a .30-rc1 base and was missing out on
on a handful of tracing fixes present in .30-rc5-almost.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We currently check for file system requests outside of blk_do_io_stat(rq),
but we may as well just include it.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Now that all block request data transfer is done via bio, rq->data
isn't used. Kill it.
While at it, make the roles of rq->special and buffer clear.
[ Impact: drop now unncessary field from struct request ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Boaz Harrosh <bharrosh@panasas.com>
There are many [__]blk_end_request() call sites which call it with
full request length and expect full completion. Many of them ensure
that the request actually completes by doing BUG_ON() the return
value, which is awkward and error-prone.
This patch adds [__]blk_end_request_all() which takes @rq and @error
and fully completes the request. BUG_ON() is added to to ensure that
this actually happens.
Most conversions are simple but there are a few noteworthy ones.
* cdrom/viocd: viocd_end_request() replaced with direct calls to
__blk_end_request_all().
* s390/block/dasd: dasd_end_request() replaced with direct calls to
__blk_end_request_all().
* s390/char/tape_block: tapeblock_end_request() replaced with direct
calls to blk_end_request_all().
[ Impact: cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
rq->start_time was initialized in init_request_from_bio() so special
requests didn't have start_time set. This has been okay as start_time
has been used only for fs requests; however, there is no indication of
this actually is the case or not. Set rq->start_time in blk_rq_init()
and guarantee that all initialized rq's have its start_time set. This
improves consistency at virtually no cost and future changes will make
use of the timestamp for !bio requests.
[ Impact: rq->start_time is valid for all requests ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Request completion has gone through several changes and became a bit
messy over the time. Clean it up.
1. end_that_request_data() is a thin wrapper around
end_that_request_data_first() which checks whether bio is NULL
before doing anything and handles bidi completion.
blk_update_request() is a thin wrapper around
end_that_request_data() which clears nr_sectors on the last
iteration but doesn't use the bidi completion.
Clean it up by moving the initial bio NULL check and nr_sectors
clearing on the last iteration into end_that_request_data() and
renaming it to blk_update_request(), which makes blk_end_io() the
only user of end_that_request_data(). Collapse
end_that_request_data() into blk_end_io().
2. There are four visible completion variants - blk_end_request(),
__blk_end_request(), blk_end_bidi_request() and end_request().
blk_end_request() and blk_end_bidi_request() uses blk_end_request()
as the backend but __blk_end_request() and end_request() use
separate implementation in __blk_end_request() due to different
locking rules.
blk_end_bidi_request() is identical to blk_end_io(). Collapse
blk_end_io() into blk_end_bidi_request(), separate out request
update into internal helper blk_update_bidi_request() and add
__blk_end_bidi_request(). Redefine [__]blk_end_request() as thin
inline wrappers around [__]blk_end_bidi_request().
3. As the whole request issue/completion usages are about to be
modified and audited, it's a good chance to convert completion
functions return bool which better indicates the intended meaning
of return values.
4. The function name end_that_request_last() is from the days when it
was a public interface and slighly confusing. Give it a proper
internal name - blk_finish_request().
5. Add description explaning that blk_end_bidi_request() can be safely
used for uni requests as suggested by Boaz Harrosh.
The only visible behavior change is from #1. nr_sectors counts are
cleared after the final iteration no matter which function is used to
complete the request. I couldn't find any place where the code
assumes those nr_sectors counters contain the values for the last
segment and this change is good as it makes the API much more
consistent as the end result is now same whether a request is
completed using [__]blk_end_request() alone or in combination with
blk_update_request().
API further cleaned up per Christoph's suggestion.
[ Impact: cleanup, rq->*nr_sectors always updated after req completion ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: Christoph Hellwig <hch@infradead.org>
With recent IDE updates, blk_end_request_callback() doesn't have any
user now. Kill it.
[ Impact: removal of unused convoluted interface ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: code reorganization
elv_next_request() and elv_dequeue_request() are public block layer
interface than actual elevator implementation. They mostly deal with
how requests interact with block layer and low level drivers at the
beginning of rqeuest processing whereas __elv_next_request() is the
actual eleveator request fetching interface.
Move the two functions to blk-core.c. This prepares for further
interface cleanup.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reorder request completion functions such that
* All request completion functions are located together.
* Functions which are used by only one caller is put right above the
caller.
* end_request() is put after other completion functions but before
blk_update_request().
This change is for completion function cleanup which will follow.
[ Impact: cleanup, code reorganization ]
Signed-off-by: Tejun Heo <tj@kernel.org>
blk_insert_request() doesn't need to worry about REQ_SOFTBARRIER.
Don't set it. Combined with recent ide updates, REQ_SOFTBARRIER is
now only used in elevator proper and for discard requests.
[ Impact: cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
RQ_NOMERGE_FLAGS already clears defines which REQ flags aren't
mergeable. There is no reason to specify it superflously. It only
adds to confusion. Don't set REQ_NOMERGE for barriers and requests
with specific queueing directive. REQ_NOMERGE is now exclusively used
by the merging code.
[ Impact: cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
blk_start_queueing() is identical to __blk_run_queue() except that it
doesn't check for recursion. None of the current users depends on
blk_start_queueing() running request_fn directly. Replace usages of
blk_start_queueing() with [__]blk_run_queue() and kill it.
[ Impact: removal of mostly duplicate interface function ]
Signed-off-by: Tejun Heo <tj@kernel.org>
__blk_run_queue wraps blk_invoke_request_fn() such that it
additionally removes plug and bails out early if the queue is empty.
Both extra operations have their own pending mechanisms and don't
cause any harm correctness-wise when they are done superflously.
The only user of blk_invoke_request_fn() being blk_start_queue(),
there isn't much reason to keep both functions around. Merge
blk_invoke_request_fn() into __blk_run_queue() and make
blk_start_queue() use __blk_run_queue() instead.
[ Impact: merge two subtly different internal functions ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Impact: subtle behavior change
For fs requests, rq is only carrier of bios and rq error status as a
whole doesn't mean much. This is the reason why rq->errors is being
cleared on each partial completion of a request as on each partial
completion the error status is transferred to the respective bios.
For pc requests, rq->errors is used to carry error status to the
issuer and thus __end_that_request_first() doesn't clear it on such
cases.
The condition was fine till now as only fs and pc requests have used
bio and thus the bio completion path. However, future changes will
unify data accesses to bio and all non fs users care about rq error
status. Clear rq->errors on bio completion only for fs requests.
In general, the implicit clearing is a bit too subtle especially as
the meaning of rq->errors is completely dependent on low level
drivers. Unifying / cleaning up rq->errors usage and letting llds
manage it would be better. TODO comment added.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jens Axboe <axboe@kernel.dk>
This simplifies I/O stat accounting switching code and separates it
completely from I/O scheduler switch code.
Requests are accounted according to the state of their request queue
at the time of the request allocation. There is no need anymore to
flush the request queue when switching I/O accounting state.
Signed-off-by: Jerome Marchand <jmarchan@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Impact: subtle behavior change
For fs requests, rq is only carrier of bios and rq error status as a
whole doesn't mean much. This is the reason why rq->errors is being
cleared on each partial completion of a request as on each partial
completion the error status is transferred to the respective bios.
For pc requests, rq->errors is used to carry error status to the
issuer and thus __end_that_request_first() doesn't clear it on such
cases.
The condition was fine till now as only fs and pc requests have used
bio and thus the bio completion path. However, future changes will
unify data accesses to bio and all non fs users care about rq error
status. Clear rq->errors on bio completion only for fs requests.
In general, the implicit clearing is a bit too subtle especially as
the meaning of rq->errors is completely dependent on low level
drivers. Unifying / cleaning up rq->errors usage and letting llds
manage it would be better. TODO comment added.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jens Axboe <axboe@kernel.dk>
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
branch tracer, intel-iommu: fix build with CONFIG_BRANCH_TRACER=y
branch tracer: Fix for enabling branch profiling makes sparse unusable
ftrace: Correct a text align for event format output
Update /debug/tracing/README
tracing/ftrace: alloc the started cpumask for the trace file
tracing, x86: remove duplicated #include
ftrace: Add check of sched_stopped for probe_sched_wakeup
function-graph: add proper initialization for init task
tracing/ftrace: fix missing include string.h
tracing: fix incorrect return type of ns2usecs()
tracing: remove CALLER_ADDR2 from wakeup tracer
blktrace: fix pdu_len when tracing packet command requests
blktrace: small cleanup in blk_msg_write()
blktrace: NUL-terminate user space messages
tracing: move scripts/trace/power.pl to scripts/tracing/power.pl
The request inherits the unplug flag from the bio, but it isn't actually
used. The bio flag stops at __make_request(), which tells it to unplug
after submission. Passing it on to the request doesn't make any sense.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This forces in_flight to be zero when turning off or on the I/O stat
accounting and stops updating I/O stats in attempt_merge() when
accounting is turned off.
Signed-off-by: Jerome Marchand <jmarchan@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
By default, CFQ will anticipate more IO from a given io context if the
previously completed IO was sync. This used to be fine, since the only
sync IO was reads and O_DIRECT writes. But with more "normal" sync writes
being used now, we don't want to anticipate for those.
Add a bio/request flag that informs the IO scheduler that this is a sync
request that we should not idle for. Introduce WRITE_ODIRECT specifically
for O_DIRECT writes, and make sure that the other sync writes set this
flag.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For the older SSD devices that don't do command queuing, we do want to
enable plugging to get better merging.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This makes sure that we never wait on async IO for sync requests, instead
of doing the split on writes vs reads.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: output all of packet commands - not just the first 4 / 8 bytes
Since commit d7e3c3249e ("block: add
large command support"), struct request->cmd has been changed from
unsinged char cmd[BLK_MAX_CDB] to unsigned char *cmd.
v1 -> v2: by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
- make sure rq->cmd_len is always intialized, and then we can use
rq->cmd_len instead of BLK_MAX_CDB.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
LKML-Reference: <49D4507E.2060602@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Put a WARN_ON in __blk_put_request if it is about to
leak bio(s). This is a serious bug that can happen in error
handling code paths.
For this to work I have fixed a couple of places in block/ where
request->bio != NULL ownership was not honored. And a small cleanup
at sg_io() while at it.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Some initial probe requests don't have disk->queue mapped yet, so we
can't rely on a non-NULL queue in blk_queue_io_stat(). Wrap it in
blk_do_io_stat().
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This allows us to turn off disk stat accounting completely, for the cases
where the 0.5-1% reduction in system time is important.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This fixes a "regression" from 2.6.28, where the barrier probes that file
systems may do would trigger additional end request warnings in dmesg.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
We just want to hand the first bits of IO to the device as fast
as possible. Gains a few percent on the IOPS rate.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* Because barrier mode can be changed dynamically, whether barrier is
supported or not can be determined only when actually issuing the
barrier and there is no point in checking it earlier. Drop barrier
support check in generic_make_request() and __make_request(), and
update comment around the support check in blk_do_ordered().
* There is no reason to check discard support in both
generic_make_request() and __make_request(). Drop the check in
__make_request(). While at it, move error action block to the end
of the function and add unlikely() to q existence test.
* Barrier request, be it empty or not, is never passed to low level
driver and thus it's meaningless to try to copy back req->sector to
bio->bi_sector on error. In addition, the notion of failed sector
doesn't make any sense for empty barrier to begin with. Drop the
code block from __end_that_request_first().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
After many improvements on kblockd_flush_work, it is now identical to
cancel_work_sync, so a direct call to cancel_work_sync is suggested.
The only difference is that cancel_work_sync is a GPL symbol,
so no non-GPL modules anymore.
Signed-off-by: Cheng Renquan <crquan@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Allow the scsi request REQ_QUIET flag to be propagated to the buffer
file system layer. The basic ideas is to pass the flag from the scsi
request to the bio (block IO) and then to the buffer layer. The buffer
layer can then suppress needless printks.
This patch declutters the kernel log by removed the 40-50 (per lun)
buffer io error messages seen during a boot in my multipath setup . It
is a good chance any real errors will be missed in the "noise" it the
logs without this patch.
During boot I see blocks of messages like
"
__ratelimit: 211 callbacks suppressed
Buffer I/O error on device sdm, logical block 5242879
Buffer I/O error on device sdm, logical block 5242879
Buffer I/O error on device sdm, logical block 5242847
Buffer I/O error on device sdm, logical block 1
Buffer I/O error on device sdm, logical block 5242878
Buffer I/O error on device sdm, logical block 5242879
Buffer I/O error on device sdm, logical block 5242879
Buffer I/O error on device sdm, logical block 5242879
Buffer I/O error on device sdm, logical block 5242879
Buffer I/O error on device sdm, logical block 5242872
"
in my logs.
My disk environment is multipath fiber channel using the SCSI_DH_RDAC
code and multipathd. This topology includes an "active" and "ghost"
path for each lun. IO's to the "ghost" path will never complete and the
SCSI layer, via the scsi device handler rdac code, quick returns the IOs
to theses paths and sets the REQ_QUIET scsi flag to suppress the scsi
layer messages.
I am wanting to extend the QUIET behavior to include the buffer file
system layer to deal with these errors as well. I have been running this
patch for a while now on several boxes without issue. A few runs of
bonnie++ show no noticeable difference in performance in my setup.
Thanks for John Stultz for the quiet_error finalization.
Submitted-by: Keith Mannthey <kmannth@us.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
For sync IO, we'll often do them serialized. This means we'll be touching
the queue timer for every IO, as opposed to only occasionally like we
do for queued IO. Instead of deleting the timer when the last request
is removed, just let continue running. If a new request comes up soon
we then don't have to readd the timer again. If no new requests arrive,
the timer will expire without side effect later.
This improves high iops sync IO by ~1%.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix setting of max_segment_size and seg_boundary mask for stacked md/dm
devices.
When stacking devices (LVM over MD over SCSI) some of the request queue
parameters are not set up correctly in some cases by default, namely
max_segment_size and and seg_boundary mask.
If you create MD device over SCSI, these attributes are zeroed.
Problem become when there is over this mapping next device-mapper mapping
- queue attributes are set in DM this way:
request_queue max_segment_size seg_boundary_mask
SCSI 65536 0xffffffff
MD RAID1 0 0
LVM 65536 -1 (64bit)
Unfortunately bio_add_page (resp. bio_phys_segments) calculates number of
physical segments according to these parameters.
During the generic_make_request() is segment cout recalculated and can
increase bio->bi_phys_segments count over the allowed limit. (After
bio_clone() in stack operation.)
Thi is specially problem in CCISS driver, where it produce OOPS here
BUG_ON(creq->nr_phys_segments > MAXSGENTRIES);
(MAXSEGENTRIES is 31 by default.)
Sometimes even this command is enough to cause oops:
dd iflag=direct if=/dev/<vg>/<lv> of=/dev/null bs=128000 count=10
This command generates bios with 250 sectors, allocated in 32 4k-pages
(last page uses only 1024 bytes).
For LVM layer, it allocates bio with 31 segments (still OK for CCISS),
unfortunatelly on lower layer it is recalculated to 32 segments and this
violates CCISS restriction and triggers BUG_ON().
The patch tries to fix it by:
* initializing attributes above in queue request constructor
blk_queue_make_request()
* make sure that blk_queue_stack_limits() inherits setting
(DM uses its own function to set the limits because it
blk_queue_stack_limits() was introduced later. It should probably switch
to use generic stack limit function too.)
* sets the default seg_boundary value in one place (blkdev.h)
* use this mask as default in DM (instead of -1, which differs in 64bit)
Bugs related to this:
https://bugzilla.redhat.com/show_bug.cgi?id=471639http://bugzilla.kernel.org/show_bug.cgi?id=8672
Signed-off-by: Milan Broz <mbroz@redhat.com>
Reviewed-by: Alasdair G Kergon <agk@redhat.com>
Cc: Neil Brown <neilb@suse.de>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
blkdev_dequeue_request() and elv_dequeue_request() are equivalent and
both start the timeout timer. Barrier code dequeues the original
barrier request but doesn't passes the request itself to lower level
driver, only broken down proxy requests; however, as the original
barrier code goes through the same dequeue path and timeout timer is
started on it. If barrier sequence takes long enough, this timer
expires but the low level driver has no idea about this request and
oops follows.
Timeout timer shouldn't have been started on the original barrier
request as it never goes through actual IO. This patch unexports
elv_dequeue_request(), which has no external user anyway, and makes it
operate on elevator proper w/o adding the timer and make
blkdev_dequeue_request() call elv_dequeue_request() and add timer.
Internal users which don't pass the request to driver - barrier code
and end_that_request_last() - are converted to use
elv_dequeue_request().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Port to the new tracepoints API: split DEFINE_TRACE() and DECLARE_TRACE()
sites. Spread them out to the usage sites, as suggested by
Mathieu Desnoyers.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
This was a forward port of work done by Mathieu Desnoyers, I changed it to
encode the 'what' parameter on the tracepoint name, so that one can register
interest in specific events and not on classes of events to then check the
'what' parameter.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move the calling blk_delete_timer to later in end_that_request_last to
address an issue where blkdev_dequeue_request may have add a timer for the
request.
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: remove __generic_unplug_device() from exports
block: move q->unplug_work initialization
blktrace: pass zfcp driver data
blktrace: add support for driver data
block: fix current kernel-doc warnings
block: only call ->request_fn when the queue is not stopped
block: simplify string handling in elv_iosched_store()
block: fix kernel-doc for blk_alloc_devt()
block: fix nr_phys_segments miscalculation bug
block: add partition attribute for partition number
block: add BIG FAT WARNING to CONFIG_DEBUG_BLOCK_EXT_DEVT
softirq: Add support for triggering softirq work on softirqs.
modprobe loop; rmmod loop effectively creates a blk_queue and destroys it
which results in q->unplug_work being canceled without it ever being
initialized.
Therefore, move the initialization of q->unplug_work from
blk_queue_make_request() to blk_alloc_queue*().
Reported-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix block kernel-doc warnings:
Warning(linux-2.6.27-git4//fs/block_dev.c:1272): No description found for parameter 'path'
Warning(linux-2.6.27-git4//block/blk-core.c:1021): No description found for parameter 'cpu'
Warning(linux-2.6.27-git4//block/blk-core.c:1021): No description found for parameter 'part'
Warning(/var/linsrc/linux-2.6.27-git4//block/genhd.c:544): No description found for parameter 'partno'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Callers should use either blk_run_queue/__blk_run_queue, or
blk_start_queueing() to invoke request handling instead of calling
->request_fn() directly as that does not take the queue stopped
flag into account.
Also add appropriate comments on the above functions to detail
their usage.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Multipath is best at handling transport errors. If it gets a device
error then there is not much the multipath layer can do. It will just
access the same device but from a different path.
This patch breaks up failfast into device, transport and driver errors.
The multipath layers (md and dm mutlipath) only ask the lower levels to
fast fail transport errors. The user of failfast, read ahead, will ask
to fast fail on all errors.
Note that blk_noretry_request will return true if any failfast bit
is set. This allows drivers that do not support the multipath failfast
bits to continue to fail on any failfast error like before. Drivers
like scsi that are able to fail fast specific errors can check
for the specific fail fast type. In the next patch I will convert
scsi.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch removes end_queued_request() and end_dequeued_request(),
which are no longer used.
As a results, users of __end_request() became only end_request().
So the actual code in __end_request() is moved to end_request()
and __end_request() is removed.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch adds an new interface, blk_lld_busy(), to check lld's
busy state from the block layer.
blk_lld_busy() calls down into low-level drivers for the checking
if the drivers set q->lld_busy_fn() using blk_queue_lld_busy().
This resolves a performance problem on request stacking devices below.
Some drivers like scsi mid layer stop dispatching request when
they detect busy state on its low-level device like host/target/device.
It allows other requests to stay in the I/O scheduler's queue
for a chance of merging.
Request stacking drivers like request-based dm should follow
the same logic.
However, there is no generic interface for the stacked device
to check if the underlying device(s) are busy.
If the request stacking driver dispatches and submits requests to
the busy underlying device, the requests will stay in
the underlying device's queue without a chance of merging.
This causes performance problem on burst I/O load.
With this patch, busy state of the underlying device is exported
via q->lld_busy_fn(). So the request stacking driver can check it
and stop dispatching requests if busy.
The underlying device driver must return the busy state appropriately:
1: when the device driver can't process requests immediately.
0: when the device driver can process requests immediately,
including abnormal situations where the device driver needs
to kill all requests.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
blk_start_queueing() should act like the generic queue unplugging
and kicking and ignore a stopped queue. Such a queue may not be
run until after a call to blk_start_queue().
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch adds a queue flag to indicate the block device can be
used for request stacking.
Request stacking drivers need to stack their devices on top of
only devices of which q->request_fn is functional.
Since bio stacking drivers (e.g. md, loop) basically initialize
their queue using blk_alloc_queue() and don't set q->request_fn,
the check of (q->request_fn == NULL) looks enough for that purpose.
However, dm will become both types of stacking driver (bio-based and
request-based). And dm will always set q->request_fn even if the dm
device is bio-based of which q->request_fn is not functional actually.
So we need something else to distinguish the type of the device.
Adding a queue flag is a solution for that.
The reason why dm always sets q->request_fn is to keep
the compatibility of dm user-space tools.
Currently, all dm user-space tools are using bio-based dm without
specifying the type of the dm device they use.
To use request-based dm without changing such tools, the kernel
must decide the type of the dm device automatically.
The automatic type decision can't be done at the device creation time
and needs to be deferred until such tools load a mapping table,
since the actual type is decided by dm target type included in
the mapping table.
So a dm device has to be initialized using blk_init_queue()
so that we can load either type of table.
Then, all queue stuffs are set (e.g. q->request_fn) and we have
no element to distinguish that it is bio-based or request-based,
even after a table is loaded and the type of the device is decided.
By the way, some stuffs of the queue (e.g. request_list, elevator)
are needless when the dm device is used as bio-based.
But the memory size is not so large (about 20[KB] per queue on ia64),
so I hope the memory loss can be acceptable for bio-based dm users.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch adds blk_insert_cloned_request(), a generic request
submission interface for request stacking drivers.
Request-based dm will use it to submit their clones to underlying
devices.
blk_rq_check_limits() is also added because it is possible that
the lower queue has stronger limitations than the upper queue
if multiple drivers are stacking at request-level.
Not only for blk_insert_cloned_request()'s internal use, the function
will be used by request-based dm when the queue limitation is
modified (e.g. by replacing dm's table).
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch adds blk_update_request(), which updates struct request
with completing its data part, but doesn't complete the struct
request itself.
Though it looks like end_that_request_first() of older kernels,
blk_update_request() should be used only by request stacking drivers.
Request-based dm will use it in bio->bi_end_io callback to update
the original request when a data part of a cloned request completes.
Followings are additional background information of why request-based
dm needs this interface.
- Request stacking drivers can't use blk_end_request() directly from
the lower driver's completion context (bio->bi_end_io or rq->end_io),
because some device drivers (e.g. ide) may try to complete
their request with queue lock held, and it may cause deadlock.
See below for detailed description of possible deadlock:
<http://marc.info/?l=linux-kernel&m=120311479108569&w=2>
- To solve that, request-based dm offloads the completion of
cloned struct request to softirq context (i.e. using
blk_complete_request() from rq->end_io).
- Though it is possible to use the same solution from bio->bi_end_io,
it will delay the notification of bio completion to the original
submitter. Also, it will cause inefficient partial completion,
because the lower driver can't perform the cloned request anymore
and request-based dm needs to requeue and redispatch it to
the lower driver again later. That's not good.
- So request-based dm needs blk_update_request() to perform the bio
completion in the lower driver's completion context, which is more
efficient.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
When a driver calls blk_cleanup_queue(), the device should be fully idle.
However, the block layer may have pending plugging timers and the IO
schedulers may have pending work in the work queues. So quisce the device
by waiting for the timer and flushing the work queues.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Right now SCSI and others do their own command timeout handling.
Move those bits to the block layer.
Instead of having a timer per command, we try to be a bit more clever
and simply have one per-queue. This avoids the overhead of having to
tear down and setup a timer for each command, so it will result in a lot
less timer fiddling.
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
We should just check for rq->bio, as that is really the information
we are looking for. Even if the bio attached doesn't carry data,
we still need to do IO post processing on it.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Somewhat incomplete, as we do allow merges of requests and bios
that have different completion CPUs given. This is done on the
assumption that a larger IO is still more beneficial than CPU
locality.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch adds support for controlling the IO completion CPU of
either all requests on a queue, or on a per-request basis. We export
a sysfs variable (rq_affinity) which, if set, migrates completions
of requests to the CPU that originally submitted it. A bio helper
(bio_set_completion_cpu()) is also added, so that queuers can ask
for completion on that specific CPU.
In testing, this has been show to cut the system time by as much
as 20-40% on synthetic workloads where CPU affinity is desired.
This requires a little help from the architecture, so it'll only
work as designed for archs that are using the new generic smp
helper infrastructure.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Move stats related fields - stamp, in_flight, dkstats - from disk to
part0 and unify stat handling such that...
* part_stat_*() now updates part0 together if the specified partition
is not part0. ie. part_stat_*() are now essentially all_stat_*().
* {disk|all}_stat_*() are gone.
* part_round_stats() is updated similary. It handles part0 stats
automatically and disk_round_stats() is killed.
* part_{inc|dec}_in_fligh() is implemented which automatically updates
part0 stats for parts other than part0.
* disk_map_sector_rcu() is updated to return part0 if no part matches.
Combined with the above changes, this makes NULL special case
handling in callers unnecessary.
* Separate stats show code paths for disk are collapsed into part
stats show code paths.
* Rename disk_stat_lock/unlock() to part_stat_lock/unlock()
While at it, reposition stat handling macros a bit and add missing
parentheses around macro parameters.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
GENHD_FL_FAIL for disk is what make_it_fail is for parts. Kill it and
use part0->make_it_fail. Sysfs node handling is unified too.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Till now, bdev->bd_part is set only if the bdev was for parts other
than part0. This patch makes bdev->bd_part always set so that code
paths don't have to differenciate common handling.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
There are two variants of stat functions - ones prefixed with double
underbars which don't care about preemption and ones without which
disable preemption before manipulating per-cpu counters. It's unclear
whether the underbarred ones assume that preemtion is disabled on
entry as some callers don't do that.
This patch unifies diskstats access by implementing disk_stat_lock()
and disk_stat_unlock() which take care of both RCU (for partition
access) and preemption (for per-cpu counter access). diskstats access
should always be enclosed between the two functions. As such, there's
no need for the versions which disables preemption. They're removed
and double underbars ones are renamed to drop the underbars. As an
extra argument is added, there's no danger of using the old version
unconverted.
disk_stat_lock() uses get_cpu() and returns the cpu index and all
diskstat functions which access per-cpu counters now has @cpu
argument to help RT.
This change adds RCU or preemption operations at some places but also
collapses several preemption ops into one at others. Overall, the
performance difference should be negligible as all involved ops are
very lightweight per-cpu ones.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
disk->part[] is protected by its matching bdev's lock. However,
non-critical accesses like collecting stats and printing out sysfs and
proc information used to be performed without any locking. As
partitions can come and go dynamically, partitions can go away
underneath those non-critical accesses. As some of those accesses are
writes, this theoretically can lead to silent corruption.
This patch fixes the race by using RCU for the partition array and dev
reference counter to hold partitions.
* Rename disk->part[] to disk->__part[] to make sure no one outside
genhd layer proper accesses it directly.
* Use RCU for disk->__part[] dereferencing.
* Implement disk_{get|put}_part() which can be used to get and put
partitions from gendisk respectively.
* Iterators are implemented to help iterate through all partitions
safely.
* Functions which require RCU readlock are marked with _rcu suffix.
* Use disk_put_part() in __blkdev_put() instead of directly putting
the contained kobject.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch makes the following misc updates in preparation for
disk->part dereference fix and extended block devt support.
* implment part_to_disk()
* fix comment about gendisk->part indexing
* rename get_part() to disk_map_sector()
* don't use n which is always zero while printing disk information in
diskstats_show()
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Remove hw_segments field from struct bio and struct request. Without virtual
merge accounting they have no purpose.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
But blkdev_issue_discard() still emits requests which are interpreted as
soft barriers, because naïve callers might otherwise issue subsequent
writes to those same sectors, which might cross on the queue (if they're
reallocated quickly enough).
Callers still _can_ issue non-barrier discard requests, but they have to
take care of queue ordering for themselves.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Some block devices benefit from a hint that they can forget the contents
of certain sectors. Add basic support for this to the block core, along
with a 'blkdev_issue_discard()' helper function which issues such
requests.
The caller doesn't get to provide an end_io functio, since
blkdev_issue_discard() will automatically split the request up into
multiple bios if appropriate. Neither does the function wait for
completion -- it's expected that callers won't care about when, or even
_if_, the request completes. It's only a hint to the device anyway. By
definition, the file system doesn't _care_ about these sectors any more.
[With feedback from OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> and
Jens Axboe <jens.axboe@oracle.com]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
cmd_filter works only for the block layer SG_IO with SCSI block
devices. It breaks scsi/sg.c, bsg, and the block layer SG_IO with SCSI
character devices (such as st). We hit a kernel crash with them.
The problem is that cmd_filter code accesses to gendisk (having struct
blk_scsi_cmd_filter) via inode->i_bdev->bd_disk. It works for only
SCSI block device files. With character device files, inode->i_bdev
leads you to struct cdev. inode->i_bdev->bd_disk->blk_scsi_cmd_filter
isn't safe.
SCSI ULDs don't expose gendisk; they keep it private. bsg needs to be
independent on any protocols. We shouldn't change ULDs to expose their
gendisk.
This patch moves struct blk_scsi_cmd_filter from gendisk to
request_queue, a common object, which eveyone can access to.
The user interface doesn't change; users can change the filters via
/sys/block/. gendisk has a pointer to request_queue so the cmd_filter
code accesses to struct blk_scsi_cmd_filter.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
blk_plug_device() must be called with the queue lock held, so callers
often just grab and release the lock for that purpose. Add a helper
that does just that.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (80 commits)
ide-floppy: fix unfortunate function naming
ide-tape: unify idetape_create_read/write_cmd
ide: add ide_pc_intr() helper
ide-{floppy,scsi}: read Status Register before stopping DMA engine
ide-scsi: add more debugging to idescsi_pc_intr()
ide-scsi: use pc->callback
ide-floppy: add more debugging to idefloppy_pc_intr()
ide-tape: always log debug info in idetape_pc_intr() if debugging is enabled
ide-tape: add ide_tape_io_buffers() helper
ide-tape: factor out DSC handling from idetape_pc_intr()
ide-{floppy,tape}: move checking of ->failed_pc to ->callback
ide: add ide_issue_pc() helper
ide: add PC_FLAG_DRQ_INTERRUPT pc flag
ide-scsi: move idescsi_map_sg() call out from idescsi_issue_pc()
ide: add ide_transfer_pc() helper
ide-scsi: set drive->scsi flag for devices handled by the driver
ide-{cd,floppy,tape}: remove checking for drive->scsi
ide: add PC_FLAG_ZIP_DRIVE pc flag
ide-tape: factor out waiting for good ireason from idetape_transfer_pc()
ide-tape: set PC_FLAG_DMA_IN_PROGRESS flag in idetape_transfer_pc()
...
Some uses blk_put_request asymmetrically, that is, they uses it with
requests that not allocated by blk_get_request. As a result,
blk_put_request has a hack to catch a NULL request_queue. Now such
callers are fixed (they use blk_get_request properly). So we can
safely remove the hack in blk_put_request.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* 'core/softirq' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
softirq: remove irqs_disabled warning from local_bh_enable
softirq: remove initialization of static per-cpu variable
Remove argument from open_softirq which is always NULL
Some block devices support verifying the integrity of requests by way
of checksums or other protection information that is submitted along
with the I/O.
This patch implements support for generating and verifying integrity
metadata, as well as correctly merging, splitting and cloning bios and
requests that have this extra information attached.
See Documentation/block/data-integrity.txt for more information.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
In function get_request_wait, the second call to get_request could be
moved to the end of the while loop, because if the first call to
get_request fails, the second call will fail without sleep.
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
As git-grep shows, open_softirq() is always called with the last argument
being NULL
block/blk-core.c: open_softirq(BLOCK_SOFTIRQ, blk_done_softirq, NULL);
kernel/hrtimer.c: open_softirq(HRTIMER_SOFTIRQ, run_hrtimer_softirq, NULL);
kernel/rcuclassic.c: open_softirq(RCU_SOFTIRQ, rcu_process_callbacks, NULL);
kernel/rcupreempt.c: open_softirq(RCU_SOFTIRQ, rcu_process_callbacks, NULL);
kernel/sched.c: open_softirq(SCHED_SOFTIRQ, run_rebalance_domains, NULL);
kernel/softirq.c: open_softirq(TASKLET_SOFTIRQ, tasklet_action, NULL);
kernel/softirq.c: open_softirq(HI_SOFTIRQ, tasklet_hi_action, NULL);
kernel/timer.c: open_softirq(TIMER_SOFTIRQ, run_timer_softirq, NULL);
net/core/dev.c: open_softirq(NET_TX_SOFTIRQ, net_tx_action, NULL);
net/core/dev.c: open_softirq(NET_RX_SOFTIRQ, net_rx_action, NULL);
This observation has already been made by Matthew Wilcox in June 2002
(http://www.cs.helsinki.fi/linux/linux-kernel/2002-25/0687.html)
"I notice that none of the current softirq routines use the data element
passed to them."
and the situation hasn't changed since them. So it appears we can safely
remove that extra argument to save 128 (54) bytes of kernel data (text).
Signed-off-by: Carlos R. Mafra <crmafra@ift.unesp.br>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
As setting and clearing queue flags now requires that we hold a spinlock
on the queue, and as blk_queue_stack_limits is called without that lock,
get the lock inside blk_queue_stack_limits.
For blk_queue_stack_limits to be able to find the right lock, each md
personality needs to set q->queue_lock to point to the appropriate lock.
Those personalities which didn't previously use a spin_lock, us
q->__queue_lock. So always initialise that lock when allocated.
With this in place, setting/clearing of the QUEUE_FLAG_PLUGGED bit will no
longer cause warnings as it will be clear that the proper lock is held.
Thanks to Dan Williams for review and fixing the silly bugs.
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Alistair John Strachan <alistair@devzero.co.uk>
Cc: Nick Piggin <npiggin@suse.de>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Jacek Luczak <difrost.kernel@gmail.com>
Cc: Prakash Punnoor <prakash@punnoor.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
get_part() is fairly expensive, as it O(N) loops over partitions
to find the right one. In lots of normal IO paths we end up looking
up the partition twice, to make matters even worse. Change the
stat add code to accept a passed in partition instead.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Original patch from Mikulas Patocka <mpatocka@redhat.com>
Mike Anderson was doing an OLTP benchmark on a computer with 48 physical
disks mapped to one logical device via device mapper.
He found that there was a slowdown on request_queue->lock in function
generic_unplug_device. The slowdown is caused by the fact that when some
code calls unplug on the device mapper, device mapper calls unplug on all
physical disks. These unplug calls take the lock, find that the queue is
already unplugged, release the lock and exit.
With the below patch, performance of the benchmark was increased by 18%
(the whole OLTP application, not just block layer microbenchmarks).
So I'm submitting this patch for upstream. I think the patch is correct,
because when more threads call simultaneously plug and unplug, it is
unspecified, if the queue is or isn't plugged (so the patch can't make
this worse). And the caller that plugged the queue should unplug it
anyway. (if it doesn't, there's 3ms timeout).
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch changes rq->cmd from the static array to a pointer to
support large commands.
We rarely handle large commands. So for optimization, a struct request
still has a static array for a command. rq_init sets rq->cmd pointer
to the static array.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This is a preparation for changing rq->cmd from the static array to a
pointer.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This rename rq_init() blk_rq_init() and export it. Any path that hands
the request to the block layer needs to call it to initialize the
request.
This is a preparation for large command support, which needs to
initialize the request in a proper way (that is, just doing a memset()
will not work).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
We can save some atomic ops in the IO path, if we clearly define
the rules of how to modify the queue flags.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This requires moving rq_init() from get_request() to blk_alloc_request().
The upside is that we can now require an rq_init() from any path that
wishes to hand the request to the block layer.
rq_init() will be exported for the code that uses struct request
without blk_get_request.
This is a preparation for large command support, which needs to
initialize struct request in a proper way (that is, just doing a
memset() will not work).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch removes the unused exports of blk_{get,put}_queue.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The meaning of rq->data_len was changed to the length of an allocated
buffer from the true data length. It breaks SG_IO friends and
bsg. This patch restores the meaning of rq->data_len to the true data
length and adds rq->extra_len to store an extended length (due to
drain buffer and padding).
This patch also removes the code to update bio in blk_rq_map_user
introduced by the commit 40b01b9bbd.
The commit adjusts bio according to memory alignment
(queue_dma_alignment). However, memory alignment is NOT padding
alignment. This adjustment also breaks SG_IO friends and bsg. Padding
alignment needs to be fixed in a proper way (by a separate patch).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <axboe@carl.home.kernel.dk>
With padding and draining moved into it, block layer now may extend
requests as directed by queue parameters, so now a request has two
sizes - the original request size and the extended size which matches
the size of area pointed to by bios and later by sgs. The latter size
is what lower layers are primarily interested in when allocating,
filling up DMA tables and setting up the controller.
Both padding and draining extend the data area to accomodate
controller characteristics. As any controller which speaks SCSI can
handle underflows, feeding larger data area is safe.
So, this patch makes the primary data length field, request->data_len,
indicate the size of full data area and add a separate length field,
request->raw_data_len, for the unmodified request size. The latter is
used to report to higher layer (userland) and where the original
request size should be fed to the controller or device.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Ingo Molnar