DSIv2 (DSI on older A family chips) has slightly different link clock
requirements.
First, we have an extra clock called src_clk (with a dedicated RCG).
This is required by the DSI controller to process the pixel data
coming from MDP. It needs to be set at the rate "pclk * bytes_per_pixel".
We also need to explicitly configure esc_clk. On DSI6G chips, we don't
need to set a rate to esc_clk because its RCG is always sourced from
crystal clock (19.2 Mhz in all cases), which is within the escape clock
frequency range in the mipi DSI spec. For chips with DSIv2, the crystal
clock rate may not be within the required range (27Mhz on APQ8064).
Therefore, we derive it from the DSI byte clock. We calculate an esc_clck
rate that is within the mipi spec and also divisible by the byte clock
rate.
When setting rate and enabling the link clocks, we make sure that byte_clk
is configured before esc_clk, and src_clk before pixel_clk. We create two
different link_enable funcs for DSI6G and DSIv2 since the sequences are
different.
We also obtain two extra source clocks (dsi_src_clk and esc_src_clk) and
set their parent to the clocks provided by DSI PLL.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI bus clocks seem to vary between different DSI host versions, and the
SOC to which they belong. Even the enable/disable sequence varies.
Provide a list of bus clock names in dsi_cfg. The driver will use this to
retrieve the clocks, and enable/disable them.
Add bus clock lists for DSI6G, and DSI for MSM8916(this is DSI6G too, but
there is no MMSS_CC specific clock since there is no MMSS clock controller
on 8916).
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Initialize clocks only after we get the DSI host version. This will allow
us to get clocks using a pre-defined list based on the DSI major/minor
version of the host. This is required since clock requirements of
different major DSI revisions(v2 vs 6g) aren't the same.
Modify dsi_get_version to get the interface clock, and then put it after
it is used.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The current version checking mechanism works fine for DSI6G blocks. It
doesn't work so well for older generation DSIv2 blocks.
The initial read of REG_DSI_6G_HW_VERSION(offset 0x0) would result in a
read of REG_DSI_CTRL for DSIv2. This register won't necessarily be 0 on
DSIv2. It can be non zero if DSI was previously initialized by the
bootloader.
Instead of reading offset 0x0, we now read offset 0x1f0. For DSIv2, this
register is DSI_VERSION, and is bound to be non-zero. On DSI6G, this
register(offset 0x1f0) is SCRATCH_REGISTER_0, which no one ever seems to
touch, and from all register dumps I'vc seen, holds 0 all the time.
Modify dsi_get_version to read REG_DSI_VERSION to determine whether we
are DSI6G or DSIv2.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We retrieve the byte and pixel source clocks (RCG clocks) in the dsi
driver via DT. These are needed so that we can re-parent these source
clocks if we want to drive it using a different DSI PLL.
We shouldn't get these via DT because they aren't clocks that directly
serve as inputs to the dsi host.
Fortunately, there is a static parent-child link between the
byte_clk_src/pixel_clk_src and byte_clk/pixel_clk clocks. So, we can
retrieve the source clocks via clk_get_parent.
Do this instead of retrieving via DT.
Cc: Rob Herring <robh@kernel.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In some configurations the supplies are voltage switches and not LDOs,
making the set voltage call to fail. Check with the regulator framework
if the supply can change voltage before attempting.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
With more platforms supported, the DSI host
configuration array keeps expanding. This change
moves those to a separate dsi_cfg module.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
There are platforms where the DSI output can be connected to another
encoder bridge chip (DSI to HDMI, DSI to LVDS etc).
Add support for external bridge support to the dsi driver. We assume that
the external bridge chip would be of the type drm_bridge. The dsi driver's
internal drm_bridge (msm_dsi->bridge) is linked to the external bridge's
drm_bridge struct.
In the case we're connected to an external bridge, we don't need to create
and manage a connector within our driver, it's the bridge driver's
responsibility to create one.
v2:
- Move the external bridge attaching stuff to dsi manager to make things
cleaner.
- Force the bridge to connect to a video mode encoder for now (the dsi
mode flags may have not been populated by modeset_init)
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We currently support only panels connected to dsi output. We're going to
also support external bridge chips now.
Change 'panel_node' to 'device_node' in the struct msm_dsi_host and
'panel_flags' to 'device_flags' in msm_dsi. This makes things sound a
bit more generic.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Platforms containing only DSI video mode devices don't need a TE gpio.
Make TE gpio optional.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The dsi host looks for the connected panel node by parsing for a child
named 'panel'. This hierarchy isn't very flexible. The connected
panel is forced to be a child to the dsi host, and hence, a mipi dsi
device. This isn't suitable for dsi devices that don't use mipi dsi
as their control bus.
Follow the of_graph approach of creating ports and endpoints to
represent the connections between the dsi host and the panel connected
to it. In our case, the dsi host will only have one output port, linked
to the panel's input port.
Update DT binding documentation with device graph usage info.
v3:
- Fix return value checks of of_graph_* calls.
- Don't make port a mandatory DT property
- Fix defer check when no panel node specified
- Rename parse_dt func to align with other dsi_host funcs
Reviewed-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Decrement device node refcount if of_get_child_by_name is successfully
called.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI PHY errors are falsely reported whenever a dsi error occurs. This is
because DSI_DLN0_PHY_ERR isn't only used as a status register, but also
used to mask PHY errors. Currently, we end up reading the mask bits too
and therefore always report errors.
Ignore the register mask bits and check for only the status/clear bits.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI controller on msm8x94 is version 1.3, which requires different
power supplies and works with 20nm DSI PHY. This change is to add
the basic support for this version.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Some targets use pinctrl framework to configure some
pins. This change allows DSI driver to set default and
sleep pinctrl status.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
I'm not sure where, exactly, but somewhere in here we must be relying on
an implicit include.
drivers/gpu/drm/msm/dsi/dsi_host.c: In function ‘dsi_host_init_panel_gpios’:
drivers/gpu/drm/msm/dsi/dsi_host.c:1356:2: error: implicit declaration of function ‘devm_gpiod_get’ [-Werror=implicit-function-declaration]
msm_host->disp_en_gpio = devm_gpiod_get(panel_device,
^
drivers/gpu/drm/msm/dsi/dsi_host.c:1356:25: warning: assignment makes pointer from integer without a cast [enabled by default]
msm_host->disp_en_gpio = devm_gpiod_get(panel_device,
^
drivers/gpu/drm/msm/dsi/dsi_host.c:1364:3: error: implicit declaration of function ‘gpiod_direction_output’ [-Werror=implicit-function-declaration]
ret = gpiod_direction_output(msm_host->disp_en_gpio, 0);
^
drivers/gpu/drm/msm/dsi/dsi_host.c:1371:20: warning: assignment makes pointer from integer without a cast [enabled by default]
msm_host->te_gpio = devm_gpiod_get(panel_device, "disp-te");
^
drivers/gpu/drm/msm/dsi/dsi_host.c:1378:3: error: implicit declaration of function ‘gpiod_direction_input’ [-Werror=implicit-function-declaration]
ret = gpiod_direction_input(msm_host->te_gpio);
^
drivers/gpu/drm/msm/dsi/dsi_host.c: In function ‘msm_dsi_host_power_on’:
drivers/gpu/drm/msm/dsi/dsi_host.c:1918:3: error: implicit declaration of function ‘gpiod_set_value’ [-Werror=implicit-function-declaration]
gpiod_set_value(msm_host->disp_en_gpio, 1);
^
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Hai Li <hali@codeaurora.org>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Rob Clark <robdclark@gmail.com>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Also there is a variant to find optional gpios that returns NULL if
there is no gpio instead of -ENOENT.
Make use of both features to simplify the driver.
This makes error checking more strict because errors like -ENOSYS ("no
gpio support compiled in") or -EPROBE_DEFER ("gpio not ready yet") are
handled correctly now.
Furthermore this is one caller less that stops us making the flags
argument to gpiod_get*() mandatory.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
There are different types of PHY from one chipset to another, while
the DSI host controller is relatively consistent across platforms.
Also, the PLL inside PHY is providing the source of DSI byte and
pixel clocks, which are used by DSI host controller. Separated devices
for clock provider and clock consumer make DSI driver better fit into
common clock framework.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change activates PLL driver for DSI to work with
common clock framework.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI byte clock and pixel clocks are sourced from DSI PLL.
This change adds the DSI PLL source clock driver under
common clock framework.
This change handles DSI 28nm PLL only.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Wentao Xu <wentaox@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
regulator_get() never returns NULL. There's no need for IS_ERR_OR_NULL()
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Some DSI peripherals rely on the HS clock on DSI clock lane as their clock
source. If the clock lane transitions between HS and LP states, it
can disrupt the functioning of such peripherals.
The mipi dsi mode flag MIPI_DSI_CLOCK_NON_CONTINUOUS already exists for
such peripheral drivers. Use it to configure the bit CLKLN_HS_FORCE_REQUEST
in DSI_LANE_CTRL.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
During cmd rx, only new versions of H/W provide register to read back
the real number of byte returned by panel. For the old versions, reading
this register will not get the right number. In fact, we only need to
assume the returned data is the same size as we expected, because later
we will check the data type to detect error.
Signed-off-by: Hai Li <hali@codeaurora.org>
Avoid such errors at compilation time:
format '%d' expects argument of type 'int', but argument 3 has type 'size_t'
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
The merge is clean, but the arm build fails afterwards,
due to API changes in the regulator tree.
I've included the patch into the merge to fix the build.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This change adds the DSI connector support in msm drm driver.
v1: Initial change
v2:
- Address comments from Archit + minor clean-ups
- Rebase to not depend on msm_drm_sub_dev change [Rob's comment]
v3: Fix issues when initialization is failed
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja