Add a dsi_cfg entry for APQ8064. Since this is the first DSIv2 chip to
be supported, add a list of bus clocks that are required by the DSIv2
block.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSIv2 (DSI on older A family chips) has slightly different link clock
requirements.
First, we have an extra clock called src_clk (with a dedicated RCG).
This is required by the DSI controller to process the pixel data
coming from MDP. It needs to be set at the rate "pclk * bytes_per_pixel".
We also need to explicitly configure esc_clk. On DSI6G chips, we don't
need to set a rate to esc_clk because its RCG is always sourced from
crystal clock (19.2 Mhz in all cases), which is within the escape clock
frequency range in the mipi DSI spec. For chips with DSIv2, the crystal
clock rate may not be within the required range (27Mhz on APQ8064).
Therefore, we derive it from the DSI byte clock. We calculate an esc_clck
rate that is within the mipi spec and also divisible by the byte clock
rate.
When setting rate and enabling the link clocks, we make sure that byte_clk
is configured before esc_clk, and src_clk before pixel_clk. We create two
different link_enable funcs for DSI6G and DSIv2 since the sequences are
different.
We also obtain two extra source clocks (dsi_src_clk and esc_src_clk) and
set their parent to the clocks provided by DSI PLL.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI bus clocks seem to vary between different DSI host versions, and the
SOC to which they belong. Even the enable/disable sequence varies.
Provide a list of bus clock names in dsi_cfg. The driver will use this to
retrieve the clocks, and enable/disable them.
Add bus clock lists for DSI6G, and DSI for MSM8916(this is DSI6G too, but
there is no MMSS_CC specific clock since there is no MMSS clock controller
on 8916).
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Initialize clocks only after we get the DSI host version. This will allow
us to get clocks using a pre-defined list based on the DSI major/minor
version of the host. This is required since clock requirements of
different major DSI revisions(v2 vs 6g) aren't the same.
Modify dsi_get_version to get the interface clock, and then put it after
it is used.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The current version checking mechanism works fine for DSI6G blocks. It
doesn't work so well for older generation DSIv2 blocks.
The initial read of REG_DSI_6G_HW_VERSION(offset 0x0) would result in a
read of REG_DSI_CTRL for DSIv2. This register won't necessarily be 0 on
DSIv2. It can be non zero if DSI was previously initialized by the
bootloader.
Instead of reading offset 0x0, we now read offset 0x1f0. For DSIv2, this
register is DSI_VERSION, and is bound to be non-zero. On DSI6G, this
register(offset 0x1f0) is SCRATCH_REGISTER_0, which no one ever seems to
touch, and from all register dumps I'vc seen, holds 0 all the time.
Modify dsi_get_version to read REG_DSI_VERSION to determine whether we
are DSI6G or DSIv2.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add DSI PLL common clock framework clocks for 8960 PHY.
The PLL here is different from the ones found in B family msm chips. As
before, the DSI provides two clocks to the outside world. dsixpll and
dsixpllbyte (x = 1, 2). dsixpll is a regular clock divider, but
dsixpllbyte is modelled as a custom clock divider.
dsixpllbyte is the starting point of the PLL configuration. It is the
one that sets up the VCO clock rate. We need the VCO clock rate in the
form: F * byteclk, where F is a multiplication factor that varies on
the byte clock the DSI driver is trying to set. We use the custom
clk_ops for dsixpllbyte to ensure that the parent (VCO) is set at this
rate.
An additional divider (POSTDIV1) generates the bitclk. Since bit clock
can be derived from byteclock, we calculate it internally, and don't
expose it as a clock.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI PHY on MSM8960 and APQ8064 is a 28nm PHY that's different from the
supported 28nm LP PHY found in newer chips.
Add support for the new PHY.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We retrieve the byte and pixel source clocks (RCG clocks) in the dsi
driver via DT. These are needed so that we can re-parent these source
clocks if we want to drive it using a different DSI PLL.
We shouldn't get these via DT because they aren't clocks that directly
serve as inputs to the dsi host.
Fortunately, there is a static parent-child link between the
byte_clk_src/pixel_clk_src and byte_clk/pixel_clk clocks. So, we can
retrieve the source clocks via clk_get_parent.
Do this instead of retrieving via DT.
Cc: Rob Herring <robh@kernel.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Create DSI encoders during modeset_init. The 2 encoders should ideally be
one command mode and one video mode DSI encoder respectively, but we don't
support command mode yet. We just create 2 of the same because the dsi
driver expects it, we end up using only the first one.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The mdp_kms round_pixclk op creates problems when we have more
interfaces in use. It calls the DTV encoder's helper by default.
Check on encoder type and call the corresponding encoder's
func meant for rounding pixel clock. DSI and LVDS don't require
rounding, so just return rate in their case.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Create an mdp4 incoder for DSI. Only DSI video mode is supported as of
now.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Vinay Simha BN <vinaysimha@inforcecomputing.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Currently, the driver defers if it doesn't find a drm_panel. This forces
us to have a drm_panel, if not, the driver isn't usable.
Make the lcdc encoder initialization independent of the availability of
the drm panel. We only check if there is a panel node specified in DT. If
it isn't, then we don't initialize the encoder at all. The panel node is
passed to the lcdc encoder and lvds connector drivers.
The connector driver takes the responsibility to retrieve the drm_panel
from the panel node, and update the status on whether the panel is
connected or not. This makes the panel usable even if the drm_panel
driver is inserted as a module later on.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
modeset_init() for mdp4 isn't very flexible. That makes it hard to add
more interfaces.
Split out the encoder/connector creation code in modeset_init into a
separate function. This is similar to what's done in modeset_init for
mdp5.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Remove CONFIG_OF checks in adreno_device.c. The downstream bus scaling
stuff is included only when CONFIG_OF is not set. So, remove that too.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We now only care about kernels that support DT. Remote the non-DT stuff.
While we're at it, use of_device_get_match_data to retrieve match data.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We don't intend to use downstream non-DT kernels anymore, so remove
CONFIG_OF checks.
Update the TODO comment so that we don't forget about max_clk setting
for non APQ8064 chips having MDP4.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Create distinct compatible strings for mdp4 and mdp5. Keep "qcom,mdss_mdp"
as is to support downstream kernels.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Support for non-DT kernels was mainly to use v3.4 downstream kernels.
This is no longer a priority now as we have reasonable support upstream.
Remove CONFIG_OF from the top level msm_drv.c file. While we're at it,
clean up the data matching process using of_device_get_match_data.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
MDP5 has line count and frame count registers for each interface. Enable
these counters and use them to implement the get_vblank_timestamp drm
driver op.
The line counter starts with the value 1 at the beginning of the VSYNC
pulse and ends with value VTOTAL at the end of VFP. This value is used
to determine whether we're in blanking period or not, and an adjusted
value of this counter is used to get vpos as expected by
get_scanout_position. Since there is no way to calculate hpos, we always
set it to 0.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWZMgaAAoJEHm+PkMAQRiGGcIH+gNS/hbN2DKW7wphl1QuaV7C
1fror8AvpwbGa/o0yuxovaVuZzAR0TF31vn+gAemF4U/hnM25xqxEHXYZEVv8OWw
mbz4/z+jbVk3SiS5AiZPIZgL4W6RZnG5QYfiTVGPlBHuBznW2ITlNlClBOmBL45o
uhb3bjTzi70AZ7Gh6i9sHgJoHg6D9u/ZxLaLcWnM79BzyTMHTf2t0wnrQmh66lEE
hp7Rn9wXv9bk/e3iH7CVUb97P4IWhhkmfqcoturqAg9+C/M26b0VmvQp9Sy8S6Pd
FVQ+SUIZllj5ZDKe9mOcs37czlxTr0keEFqzWeMh/7y4iuI3RaRp/qb+7mX5sIE=
=WGZ1
-----END PGP SIGNATURE-----
Back merge tag 'v4.4-rc4' into drm-next
We've picked up a few conflicts and it would be nice
to resolve them before we move onwards.
New -misc pull. Big thing is Thierry's atomic helpers for system suspend
resume, which I'd like to use in i915 too. Hence the pull.
* tag 'topic/drm-misc-2015-12-04' of git://anongit.freedesktop.org/drm-intel:
drm: keep connector status change logging human readable
drm/atomic-helper: Reject attempts at re-stealing encoders
drm/atomic-helper: Implement subsystem-level suspend/resume
drm: Implement drm_modeset_lock_all_ctx()
drm/gma500: Add driver private mutex for the fault handler
drm/gma500: Drop dev->struct_mutex from mmap offset function
drm/gma500: Drop dev->struct_mutex from fbdev init/teardown code
drm/gma500: Drop dev->struct_mutex from modeset code
drm/gma500: Use correct unref in the gem bo create function
drm/edid: Make the detailed timing CEA/HDMI mode fixup accept up to 5kHz clock difference
drm/atomic_helper: Add drm_atomic_helper_disable_planes_on_crtc()
drm: Serialise multiple event readers
drm: Drop dev->event_lock spinlock around faulting copy_to_user()
A few more last minute fixes for 4.4 on top of my pull request from
earlier this week. The big change here is a vblank regression fix due to
commit 4dfd6486 "drm: Use vblank timestamps to guesstimate how many vblanks
were missed". Beyond that, a hotplug fix and a few VM fixes.
* 'drm-fixes-4.4' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: Fixup hw vblank counter/ts for new drm_update_vblank_count() (v3)
drm/radeon: Fixup hw vblank counter/ts for new drm_update_vblank_count() (v2)
drm/radeon: Retry DDC probing on DVI on failure if we got an HPD interrupt
drm/amdgpu: add spin lock to protect freed list in vm (v2)
drm/amdgpu: partially revert "drm/amdgpu: fix VM_CONTEXT*_PAGE_TABLE_END_ADDR" v2
drm/amdgpu: take a BO reference for the user fence
drm/amdgpu: take a BO reference in the display code
drm/amdgpu: set snooped flags only on system addresses v2
drm/amdgpu: fix race condition in amd_sched_entity_push_job
drm/amdgpu: add err check for pin userptr
add blacklist for thinkpad T40p
drm/amdgpu: fix VM page table reference counting
drm/amdgpu: fix userptr flags check
commit 4dfd6486 "drm: Use vblank timestamps to guesstimate how many
vblanks were missed" introduced in Linux 4.4-rc1 makes the drm core
more fragile to drivers which don't update hw vblank counters and
vblank timestamps in sync with firing of the vblank irq and
essentially at leading edge of vblank.
This exposed a problem with radeon-kms/amdgpu-kms which do not
satisfy above requirements:
The vblank irq fires a few scanlines before start of vblank, but
programmed pageflips complete at start of vblank and
vblank timestamps update at start of vblank, whereas the
hw vblank counter increments only later, at start of vsync.
This leads to problems like off by one errors for vblank counter
updates, vblank counters apparently going backwards or vblank
timestamps apparently having time going backwards. The net result
is stuttering of graphics in games, or little hangs, as well as
total failure of timing sensitive applications.
See bug #93147 for an example of the regression on Linux 4.4-rc:
https://bugs.freedesktop.org/show_bug.cgi?id=93147
This patch tries to align all above events better from the
viewpoint of the drm core / of external callers to fix the problem:
1. The apparent start of vblank is shifted a few scanlines earlier,
so the vblank irq now always happens after start of this extended
vblank interval and thereby drm_update_vblank_count() always samples
the updated vblank count and timestamp of the new vblank interval.
To achieve this, the reporting of scanout positions by
radeon_get_crtc_scanoutpos() now operates as if the vblank starts
radeon_crtc->lb_vblank_lead_lines before the real start of the hw
vblank interval. This means that the vblank timestamps which are based
on these scanout positions will now update at this earlier start of
vblank.
2. The driver->get_vblank_counter() function will bump the returned
vblank count as read from the hw by +1 if the query happens after
the shifted earlier start of the vblank, but before the real hw increment
at start of vsync, so the counter appears to increment at start of vblank
in sync with the timestamp update.
3. Calls from vblank irq-context and regular non-irq calls are now
treated identical, always simulating the shifted vblank start, to
avoid inconsistent results for queries happening from vblank irq vs.
happening from drm_vblank_enable() or vblank_disable_fn().
4. The radeon_flip_work_func will delay mmio programming a pageflip until
the start of the real vblank iff it happens to execute inside the shifted
earlier start of the vblank, so pageflips now also appear to execute at
start of the shifted vblank, in sync with vblank counter and timestamp
updates. This to avoid some races between updates of vblank count and
timestamps that are used for swap scheduling and pageflip execution which
could cause pageflips to execute before the scheduled target vblank.
The lb_vblank_lead_lines "fudge" value is calculated as the size of
the display controllers line buffer in scanlines for the given video
mode: Vblank irq's are triggered by the line buffer logic when the line
buffer refill for a video frame ends, ie. when the line buffer source read
position enters the hw vblank. This means that a vblank irq could fire at
most as many scanlines before the current reported scanout position of the
crtc timing generator as the number of scanlines the line buffer can
maximally hold for a given video mode.
This patch has been successfully tested on a RV730 card with DCE-3 display
engine and on a evergreen card with DCE-4 display engine, in single-display
and dual-display configuration, with different video modes.
A similar patch is needed for amdgpu-kms to fix the same problem.
Limitations:
- Maybe replace the udelay() in the flip_work_func() by a suitable
usleep_range() for a bit better efficiency? Will try that.
- Line buffer sizes in pixels are hard-coded on < DCE-4 to a value
i just guessed to be high enough to work ok, lacking info on the true
sizes atm.
Probably fixes: fdo#93147
Port of Mario's radeon fix to amdgpu.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(v1) Reviewed-by: Mario Kleiner <mario.kleiner.de@gmail.com>
(v2) Refine amdgpu_flip_work_func() for better efficiency.
In amdgpu_flip_work_func, replace the busy waiting udelay(5)
with event lock held by a more performance and energy efficient
usleep_range() until at least predicted true start of hw vblank,
with some slack for scheduler happiness. Release the event lock
during waits to not delay other outputs in doing their stuff, as
the waiting can last up to 200 usecs in some cases.
Also small fix to code comment and formatting in that function.
(v2) Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
(v3) Fix crash in crtc disabled case
commit 4dfd6486 "drm: Use vblank timestamps to guesstimate how many
vblanks were missed" introduced in Linux 4.4-rc1 makes the drm core
more fragile to drivers which don't update hw vblank counters and
vblank timestamps in sync with firing of the vblank irq and
essentially at leading edge of vblank.
This exposed a problem with radeon-kms/amdgpu-kms which do not
satisfy above requirements:
The vblank irq fires a few scanlines before start of vblank, but
programmed pageflips complete at start of vblank and
vblank timestamps update at start of vblank, whereas the
hw vblank counter increments only later, at start of vsync.
This leads to problems like off by one errors for vblank counter
updates, vblank counters apparently going backwards or vblank
timestamps apparently having time going backwards. The net result
is stuttering of graphics in games, or little hangs, as well as
total failure of timing sensitive applications.
See bug #93147 for an example of the regression on Linux 4.4-rc:
https://bugs.freedesktop.org/show_bug.cgi?id=93147
This patch tries to align all above events better from the
viewpoint of the drm core / of external callers to fix the problem:
1. The apparent start of vblank is shifted a few scanlines earlier,
so the vblank irq now always happens after start of this extended
vblank interval and thereby drm_update_vblank_count() always samples
the updated vblank count and timestamp of the new vblank interval.
To achieve this, the reporting of scanout positions by
radeon_get_crtc_scanoutpos() now operates as if the vblank starts
radeon_crtc->lb_vblank_lead_lines before the real start of the hw
vblank interval. This means that the vblank timestamps which are based
on these scanout positions will now update at this earlier start of
vblank.
2. The driver->get_vblank_counter() function will bump the returned
vblank count as read from the hw by +1 if the query happens after
the shifted earlier start of the vblank, but before the real hw increment
at start of vsync, so the counter appears to increment at start of vblank
in sync with the timestamp update.
3. Calls from vblank irq-context and regular non-irq calls are now
treated identical, always simulating the shifted vblank start, to
avoid inconsistent results for queries happening from vblank irq vs.
happening from drm_vblank_enable() or vblank_disable_fn().
4. The radeon_flip_work_func will delay mmio programming a pageflip until
the start of the real vblank iff it happens to execute inside the shifted
earlier start of the vblank, so pageflips now also appear to execute at
start of the shifted vblank, in sync with vblank counter and timestamp
updates. This to avoid some races between updates of vblank count and
timestamps that are used for swap scheduling and pageflip execution which
could cause pageflips to execute before the scheduled target vblank.
The lb_vblank_lead_lines "fudge" value is calculated as the size of
the display controllers line buffer in scanlines for the given video
mode: Vblank irq's are triggered by the line buffer logic when the line
buffer refill for a video frame ends, ie. when the line buffer source read
position enters the hw vblank. This means that a vblank irq could fire at
most as many scanlines before the current reported scanout position of the
crtc timing generator as the number of scanlines the line buffer can
maximally hold for a given video mode.
This patch has been successfully tested on a RV730 card with DCE-3 display
engine and on a evergreen card with DCE-4 display engine, in single-display
and dual-display configuration, with different video modes.
A similar patch is needed for amdgpu-kms to fix the same problem.
Limitations:
- Line buffer sizes in pixels are hard-coded on < DCE-4 to a value
i just guessed to be high enough to work ok, lacking info on the true
sizes atm.
Fixes: fdo#93147
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Michel Dänzer <michel.daenzer@amd.com>
Cc: Harry Wentland <Harry.Wentland@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
(v1) Tested-by: Dave Witbrodt <dawitbro@sbcglobal.net>
(v2) Refine radeon_flip_work_func() for better efficiency:
In radeon_flip_work_func, replace the busy waiting udelay(5)
with event lock held by a more performance and energy efficient
usleep_range() until at least predicted true start of hw vblank,
with some slack for scheduler happiness. Release the event lock
during waits to not delay other outputs in doing their stuff, as
the waiting can last up to 200 usecs in some cases.
Retested on DCE-3 and DCE-4 to verify it still works nicely.
(v2) Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
HPD signals on DVI ports can be fired off before the pins required for
DDC probing actually make contact, due to the pins for HPD making
contact first. This results in a HPD signal being asserted but DDC
probing failing, resulting in hotplugging occasionally failing.
This is somewhat rare on most cards (depending on what angle you plug
the DVI connector in), but on some cards it happens constantly. The
Radeon R5 on the machine used for testing this patch for instance, runs
into this issue just about every time I try to hotplug a DVI monitor and
as a result hotplugging almost never works.
Rescheduling the hotplug work for a second when we run into an HPD
signal with a failing DDC probe usually gives enough time for the rest
of the connector's pins to make contact, and fixes this issue.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
there is a protection fault about freed list when OCL test.
add a spin lock to protect it.
v2: drop changes in vm_fini
Signed-off-by: JimQu <jim.qu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
The gtt_end is already inclusive, we don't need to subtract one here.
v2 (chk): keep the fix for the VM code, cause here it really applies.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Anatoli Antonovitch <anatoli.antonovitch@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No need for a GEM reference here.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No need for the GEM reference here.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Not necessary for VRAM.
v2: no need to check if ttm is NULL.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We've had human readable connector status change debug logging since
commit ed7951dc13
Author: Lespiau, Damien <damien.lespiau@intel.com>
Date: Fri May 10 12:36:42 2013 +0000
drm: Make the HPD status updates debug logs more readable
but
commit 162b6a57ac
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Jan 21 08:45:21 2015 +0100
drm/probe-helper: don't lose hotplug event
added a new one with just the numbers. Fix it.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449144003-2877-1-git-send-email-jani.nikula@intel.com
Apparently pre-nv50 pageflip events happen before the actual vblank
period. Therefore that functionality got semi-disabled in
commit af4870e406
Author: Mario Kleiner <mario.kleiner.de@gmail.com>
Date: Tue May 13 00:42:08 2014 +0200
drm/nouveau/kms/nv04-nv40: fix pageflip events via special case.
Unfortunately that hack got uprooted in
commit cc1ef118fc
Author: Thierry Reding <treding@nvidia.com>
Date: Wed Aug 12 17:00:31 2015 +0200
drm/irq: Make pipe unsigned and name consistent
Triggering a warning when trying to sample the vblank timestamp for a
non-existing pipe. There's a few ways to fix this:
- Open-code the old behaviour, which just enshrines this slight
breakage of the userspace ABI.
- Revert Mario's commit and again inflict broken timestamps, again not
pretty.
- Fix this for real by delaying the pageflip TS until the next vblank
interrupt, thereby making it accurate.
This patch implements the third option. Since having a page flip
interrupt that happens when the pageflip gets armed and not when it
completes in the next vblank seems to be fairly common (older i915 hw
works very similarly) create a new helper to arm vblank events for
such drivers.
v2 (Mario Kleiner):
- Fix function prototypes in drmP.h
- Add missing vblank_put() for pageflip completion without
pageflip event.
- Initialize sequence number for queued pageflip event to avoid
trouble in drm_handle_vblank_events().
- Remove dead code and spelling fix.
v3 (Mario Kleiner):
- Add a signed-off-by and cc stable tag per Ilja's advice.
v4 (Thierry Reding):
- Fix kerneldoc typo, discovered by Michel Dänzer
- Rearrange tags and changelog
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=106431
Cc: Thierry Reding <treding@nvidia.com>
Cc: Mario Kleiner <mario.kleiner.de@gmail.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: stable@vger.kernel.org # v4.3
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
A client calling drmSetMaster() using a file descriptor that was opened
when another client was master would inherit the latter client's master
object and all its authenticated clients.
This is unwanted behaviour, and when this happens, instead allocate a
brand new master object for the client calling drmSetMaster().
Fixes a BUG() throw in vmw_master_set().
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Use drm_crtc_send_vblank_event to fix per crtc vblank handling
- Move the crtc device of_node assignment out of the ipuv3-crtc driver into
ipu-common code, where the devices are created.
- Fix parallel display support with simple-panels
- Remove some unused fields and superfluous checks
- Switch to universal planes and add error handling for primary plane creation
- Fix module autoload for TV encoder driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iEJU
-----END PGP SIGNATURE-----
Merge tag 'imx-drm-fixes-2015-12-01' of git://git.pengutronix.de/git/pza/linux into drm-fixes
imx-drm crtc, plane, parallel panel, and TV encoder fixes
- Use drm_crtc_send_vblank_event to fix per crtc vblank handling
- Move the crtc device of_node assignment out of the ipuv3-crtc driver into
ipu-common code, where the devices are created.
- Fix parallel display support with simple-panels
- Remove some unused fields and superfluous checks
- Switch to universal planes and add error handling for primary plane creation
- Fix module autoload for TV encoder driver
* tag 'imx-drm-fixes-2015-12-01' of git://git.pengutronix.de/git/pza/linux:
drm: imx: imx-tve: Fix module autoload for OF platform driver
drm: imx: convert to drm_crtc_send_vblank_event()
GPU-DRM-IMX: Delete an unnecessary check before drm_fbdev_cma_restore_mode()
drm/imx: Remove of_node assignment from ipuv3-crtc driver probe
gpu: ipu-v3: Assign of_node of child platform devices to corresponding ports
gpu: ipu-v3: Remove reg_offset field
gpu: ipu-v3: drop unused dmfc field from client platform data
drm/imx: parallel-display: allow to determine bus format from the connected panel
drm/imx: ipuv3-crtc: Return error if ipu_plane_init() fails for primary plane
drm/imx: switch to universal planes
Another batch of drm/i915 fixes for v4.4, on top of the ones from
earlier this week. One timeout handling regression fix from Chris, and
backport of five patches from our -next to fix a power management
related HDMI hotplug regression.
* tag 'drm-intel-fixes-2015-12-03' of git://anongit.freedesktop.org/drm-intel:
drm/i915: take a power domain reference while checking the HDMI live status
drm/i915: add MISSING_CASE to a few port/aux power domain helpers
drm/i915/ddi: fix intel_display_port_aux_power_domain() after HDMI detect
drm/i915: Introduce a gmbus power domain
drm/i915: Clean up AUX power domain handling
drm/i915: Check the timeout passed to i915_wait_request
This can happen when we run out of encoders for a multi-crtc modeset,
or also when userspace is silly and tries to clone multiple connectors
that need the same encoder on the same crtc.
Reported-and-Tested-and-Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449136154-11588-1-git-send-email-daniel.vetter@ffwll.ch
This function is like drm_modeset_lock_all(), but it takes the lock
acquisition context as a parameter rather than storing it in the DRM
device's mode_config structure.
Implement drm_modeset_{,un}lock_all() in terms of the new function for
better code reuse, and add a note to the kerneldoc that new code should
use the new functions.
v2: improve kerneldoc
v4: rename drm_modeset_lock_all_crtcs() to drm_modeset_lock_all_ctx()
and take mode_config's .connection_mutex instead of .mutex lock to
avoid lock inversion (Daniel Vetter), use drm_modeset_drop_locks()
which is now the equivalent of drm_modeset_unlock_all_ctx()
v5: do not take the dev->mode_config.connection_mutex in
drm_atomic_legacy_backoff() since drm_modeset_lock_all_ctx()
already keeps it, enhance kerneldoc for drm_modeset_lock_all_ctx()
(Daniel Vetter)
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449075005-13937-1-git-send-email-thierry.reding@gmail.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As soon as we leave the spinlock after the job has been added to the job
queue, we can no longer rely on the job's data to be available.
I have seen a null-pointer dereference due to sched == NULL in
amd_sched_wakeup via amd_sched_entity_push_job and
amd_sched_ib_submit_kernel_helper. Since the latter initializes
sched_job->sched with the address of the ring scheduler, which is
guaranteed to be non-NULL, this race appears to be a likely culprit.
Signed-off-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Bugzilla: https://bugs.freedesktop.org/attachment.cgi?bugid=93079
Reviewed-by: Christian König <christian.koenig@amd.com>
Missing error check if the operation failed.
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
There are platforms that don't need the full GMBUS power domain (BXT)
while others do (PCH, VLV/CHV). For optimizing this we would need to add
a new power domain, but it's not clear how much we would benefit given
the short time we hold the reference. So for now let's keep things
simple.
This fixes a regression introduced in
commit 237ed86c69
Author: Sonika Jindal <sonika.jindal@intel.com>
Date: Tue Sep 15 09:44:20 2015 +0530
drm/i915: Check live status before reading edid
v2:
- fix commit message, PCH won't take any redundant power resource after
this change (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[fix commit message in v2 (Imre)]
[Cherry-picked from drm-intel-next-queued 29bb94bb (Imre)]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448643329-18675-6-git-send-email-imre.deak@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
MISSING_CASE() would have been useful to track down a recent problem in
intel_display_port_aux_power_domain(), so add it there and a few related
helpers. This was also suggested by Ville in his review of the latest
DMC/DC changes, we forgot to address that.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
[Cherry-picked from drm-intel-next-queued b9fec167 (Imre)]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448643329-18675-5-git-send-email-imre.deak@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Due to the current sharing of the DDI encoder between DP and HDMI
connectors we can run the DP detection after the HDMI detection has
already set the shared encoder's type. For now solve this keeping the
current behavior and running the detection in this case too. For a proper
solution Ville suggested to split the encoder into an HDMI and DP one, that
can be done as a follow-up.
This issue triggers the WARN in intel_display_port_aux_power_domain() and
was introduced in:
commit 25f78f58e5
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Nov 16 15:01:04 2015 +0100
drm/i915: Clean up AUX power domain handling
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
[Cherry-picked from drm-intel-next-queued 651174a4 (Imre)]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448643329-18675-4-git-send-email-imre.deak@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Currently the gmbus code uses intel_aux_display_runtime_get/put in an
effort to make sure the hardware is powered up sufficiently for gmbus.
That function only takes the runtime PM reference which on VLV/CHV/BXT
is not enough. We need the disp2d/pipe-a well on VLV/CHV and power well
2 on BXT. So add a new power domnain for gmbus and kill off the now
unused intel_aux_display_runtime_get/put. And change
intel_hdmi_set_edid() to use the gmbus power domain too since that's all
we need there.
Also toss in a BUILD_BUG_ON() to catch problems if we run out of
bits for power domains. We're already really close to the limit...
[Patrik: Add gmbus string to debugfs output]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
[Cherry-picked from drm-intel-next-queued f0ab43e6 (Imre)]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448643329-18675-3-git-send-email-imre.deak@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Introduce intel_display_port_aux_power_domain() which simply returns
the appropriate AUX power domain for a specific port, and then replace
the intel_display_port_power_domain() with calls to the new function
in the DP code. As long as we're not actually enabling the port we don't
need the lane power domains, and those are handled now purely from
modeset_update_crtc_power_domains().
My initial motivation for this was to see if I could keep the DPIO power
wells powered down while doing AUX on CHV, but turns out I can't so this
doesn't change anything for CHV at least. But I think it's still a
worthwile change.
v2: Add case for PORT E. Default to POWER_DOMAIN_AUX_D for now. (Ville)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
[Cherry-picked from drm-intel-next-queued 25f78f58 (Imre)]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1448643329-18675-2-git-send-email-imre.deak@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Passing -1 as the pipe for vblank events now triggers a WARN_ON, but had
previously made multi-screen unusable anyway. Pass the correct pipe to
the event-send function, and use the new API to make this a bit easier
for us.
Fixes WARN present since cc1ef118fc for every pageflip event sent:
[ 209.549969] ------------[ cut here ]------------
[ 209.554592] WARNING: CPU: 3 PID: 238 at drivers/gpu/drm/drm_irq.c:924 drm_vblank_count_and_time+0x80/0x88 [drm]()
[ 209.564832] Modules linked in: [...]
[ 209.612401] CPU: 3 PID: 238 Comm: irq/41-ff940000 Tainted: G W 4.3.0-rc6+ #71
[ 209.620647] Hardware name: Rockchip (Device Tree)
[ 209.625348] [<c001bb80>] (unwind_backtrace) from [<c001615c>] (show_stack+0x20/0x24)
[ 209.633079] [<c001615c>] (show_stack) from [<c02b2c50>] (dump_stack+0x8c/0x9c)
[ 209.640289] [<c02b2c50>] (dump_stack) from [<c0052e88>] (warn_slowpath_common+0x94/0xc4)
[ 209.648364] [<c0052e88>] (warn_slowpath_common) from [<c0052f74>] (warn_slowpath_null+0x2c/0x34)
[ 209.657139] [<c0052f74>] (warn_slowpath_null) from [<bf17dc30>] (drm_vblank_count_and_time+0x80/0x88 [drm])
[ 209.666875] [<bf17dc30>] (drm_vblank_count_and_time [drm]) from [<bf17e484>] (drm_send_vblank_event+0x74/0x7c [drm])
[ 209.677385] [<bf17e484>] (drm_send_vblank_event [drm]) from [<bf4c1144>] (vop_win_state_complete+0x4c/0x70 [rockchip_drm_vop])
[ 209.688757] [<bf4c1144>] (vop_win_state_complete [rockchip_drm_vop]) from [<bf4c3bdc>] (vop_isr_thread+0x170/0x1d4 [rockchip_drm_vop])
[ 209.700822] [<bf4c3bdc>] (vop_isr_thread [rockchip_drm_vop]) from [<c00ab93c>] (irq_thread_fn+0x2c/0x50)
[ 209.710284] [<c00ab93c>] (irq_thread_fn) from [<c00abcac>] (irq_thread+0x13c/0x188)
[ 209.717927] [<c00abcac>] (irq_thread) from [<c00723c8>] (kthread+0xec/0x104)
[ 209.724965] [<c00723c8>] (kthread) from [<c0011638>] (ret_from_fork+0x14/0x3c)
[ 209.732171] ---[ end trace 0690bc604f5d535d ]---
Signed-off-by: Daniel Stone <daniels@collabora.com>
Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Tested-By: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Thierry Reding <treding@nvidia.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
VOP_WINx_DSP_ST does not require subtracting 1 from the values written to
it. It actually causes the screen to be shifted by one pixel.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Tested-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dominik Behr <dbehr@chromium.org>
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Commit 371f0f085f ("ARM: 8426/1: dma-mapping: add missing range check
in dma_mmap()") introduced offset-checking for mappings, which collides
with the fake-offset the drm sets for gems.
Other drm-drivers set this offset to 0 before doing the mapping, so
this looks like the correct way to go for rockchip as well.
Fixes: 371f0f085f ("ARM: 8426/1: dma-mapping: add missing range check in dma_mmap()")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Archit Taneja