Add support for the rk805 regulator. The regulator module consists
of 4 DCDCs, 3 LDOs.
The output voltages are configurable and are meant to supply power
to the main processor and other components.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Set the correct voltage select register for LDO2.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
RK808_ID_DCDC1 is 0, no need to do subtract RK808_ID_DCDC1.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Add the MFD bindings doc to MAINTAINERS
- New Drivers
- X-Powers AC100 Audio CODEC and RTC
- TI LP873x PMIC
- Rockchip RK808 PMIC
- Samsung Exynos Low Power Audio
- New Device Support
- Add support for STMPE1600 variant to stmpe
- Add support for PM8018 PMIC to pm8921-core
- Add support for AXP806 PMIC in axp20x
- Add support for AXP209 GPIO in axp20x
- New Functionality
- Add support for Reset to all STMPE variants
- Add support for MKBP event support to cros_ec
- Add support for USB to intel_soc_pmic_bxtwc
- Add support for IRQs and Power Button to tps65217
- Fix-ups
- Clean-up defunct author emails; da9063, max14577
- Kconfig fixups; wm8350-i2c, as3722
- Constify; altera-a10sr, sm501
- Supply PCI IDs; intel-lpss-pci
- Improve clocking; qcom_rpm
- Fix IRQ probing; ucb1x00-core
- Ensure fault log is cleared; da9052
- Remove NO_IRQ check; ucb1x00-core
- Supply I2C properties; intel-lpss-acpi, intel-lpss-pci
- Non standard declaration; tps65217, max8997-irq
- Remove unused code; lp873x, db8500-prcmu, ab8500-debugfs,
cros_ec_spi
- Make non-modular; altera-a10sr, intel_msic, smsc-ece1099,
sun6i-prcm, twl-core,
- OF bindings; ac100, stmpe, qcom-pm8xxx, qcom-rpm, rk808,
axp20x, lp873x, exynos5433-lpass, act8945a,
aspeed-scu, twl6040, arizona
- Bug Fixes
- Release OF pointer; qcom_rpm
- Avoid double shifting in suspend/resume; 88pm80x
- Fix 'defined but not used' error; exynos-lpass
- Fix 'sleeping whilst attomic'; atmel-hlcdc
-----BEGIN PGP SIGNATURE-----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=Ja7p
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core framework:
- Add the MFD bindings doc to MAINTAINERS
New drivers:
- X-Powers AC100 Audio CODEC and RTC
- TI LP873x PMIC
- Rockchip RK808 PMIC
- Samsung Exynos Low Power Audio
New device support:
- Add support for STMPE1600 variant to stmpe
- Add support for PM8018 PMIC to pm8921-core
- Add support for AXP806 PMIC in axp20x
- Add support for AXP209 GPIO in axp20x
New functionality:
- Add support for Reset to all STMPE variants
- Add support for MKBP event support to cros_ec
- Add support for USB to intel_soc_pmic_bxtwc
- Add support for IRQs and Power Button to tps65217
Fix-ups:
- Clean-up defunct author emails (da9063, max14577)
- Kconfig fixups (wm8350-i2c, as37220
- Constify (altera-a10sr, sm501)
- Supply PCI IDs (intel-lpss-pci)
- Improve clocking (qcom_rpm)
- Fix IRQ probing (ucb1x00-core)
- Ensure fault log is cleared (da9052)
- Remove NO_IRQ check (ucb1x00-core)
- Supply I2C properties (intel-lpss-acpi, intel-lpss-pci)
- Non standard declaration (tps65217, max8997-irq)
- Remove unused code (lp873x, db8500-prcmu, ab8500-debugfs,
cros_ec_spi)
- Make non-modular (altera-a10sr, intel_msic, smsc-ece1099,
sun6i-prcm, twl-core)
- OF bindings (ac100, stmpe, qcom-pm8xxx, qcom-rpm, rk808, axp20x,
lp873x, exynos5433-lpass, act8945a, aspeed-scu, twl6040, arizona)
Bugfixes:
- Release OF pointer (qcom_rpm)
- Avoid double shifting in suspend/resume (88pm80x)
- Fix 'defined but not used' error (exynos-lpass)
- Fix 'sleeping whilst attomic' (atmel-hlcdc)"
* tag 'mfd-for-linus-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (69 commits)
mfd: arizona: Handle probe deferral for reset GPIO
mfd: arizona: Remove arizona_of_get_named_gpio helper function
mfd: arizona: Add DT options for max_channels_clocked and PDM speaker config
mfd: twl6040: Register child device for twl6040-pdmclk
mfd: cros_ec_spi: Remove unused variable 'request'
mfd: omap-usb-host: Return value is not 'const int'
mfd: ab8500-debugfs: Remove 'weak' function suspend_test_wake_cause_interrupt_is_mine()
mfd: ab8500-debugfs: Remove ab8500_dump_all_banks_to_mem()
mfd: db8500-prcmu: Remove unused *prcmu_set_ddr_opp() calls
mfd: ab8500-debugfs: Prevent initialised field from being over-written
mfd: max8997-irq: 'inline' should be at the beginning of the declaration
mfd: rk808: Fix RK818_IRQ_DISCHG_ILIM initializer
mfd: tps65217: Fix nonstandard declaration
mfd: lp873x: Remove unused mutex lock from struct lp873x
mfd: atmel-hlcdc: Do not sleep in atomic context
mfd: exynos-lpass: Mark PM functions as __maybe_unused
mfd: intel-lpss: Add default I2C device properties for Apollo Lake
mfd: twl-core: Make it explicitly non-modular
mfd: sun6i-prcm: Make it explicitly non-modular
mfd: smsc-ece1099: Make it explicitly non-modular
...
Add support for the rk818 regulator. The regulator module consists
of 4 DCDCs, 9 LDOs, 1 switch and 1 BOOST converter which is used to
power OTG and HDMI5V.
The output voltages are configurable and are meant to supply power
to the main processor and other components.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The field "owner" is set by core. Thus delete an extra initialisation.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
A common simplified DT parsing code for regulators was introduced in
commit a0c7b164ad ("regulator: of: Provide simplified DT parsing
method")
While at it also added RK8XX_DESC and RK8XX_DESC_SWITCH macros for the
regulator_desc struct initialization. This just makes the driver more compact.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
LDO_REG3 descriptor is using linear_ranges.
Add and use proper ops for LDO_REG3.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
After removing all uses of the range operations in a recent patch,
we get a warning about the symbol not being referenced anywhere:
drivers/regulator/rk808-regulator.c:306:29: 'rk808_reg_ops_ranges' defined but not used
This removes the now-unused structure along with the
rk808_set_suspend_voltage_range function that is only referenced from
rk808_reg_ops_ranges.
Fixes: afcd666d9d ("regulator: rk808: remove linear range definitions with a single range")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver was using only linear ranges. Now we remove linear range
definitions with a single range. So we have to add an ops struct for
ranges and adjust all other ops functions accordingly.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The gpiod functions include variants for managed gpiod resources. Use it
to simplify the remove function.
As the driver handles a device node without a specification of dvs gpios
just fine, additionally use the variant of gpiod_get exactly for this
use case. This makes error checking more strict.
As a third benefit this patch makes the driver use the flags parameter
of gpiod_get* which will not be optional any more after 4.2 and so
prevents a build failure when the respective gpiod commit is merged.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes a build problem on mips found by the kbuild test robot:
drivers/regulator/rk808-regulator.c: In function 'rk808_buck1_2_get_voltage_sel_regmap':
drivers/regulator/rk808-regulator.c:97:2: error: implicit declaration of function 'gpiod_get_value' [-Werror=implicit-function-declaration]
if (IS_ERR(gpio) || gpiod_get_value(gpio) == 0)
^
Fixes: bad47ad2ee ("regulator: rk808: fixed the overshoot when adjust voltage")
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a overshoot in DCDC1/DCDC2, we have 2 method to workaround:
1st is use dvs pin to switch the voltage between value in BUCKn_ON_VSEL
and BUCKn_DVS_VSEL. If DVS pin is inactive, the voltage of DCDC1/DCDC2
are controlled by BUCKn_ON_VSEL, when we pull dvs1/dvs2 pin to active,
they would be controlled by BUCKn_DVS_VSEL. In this case, the ramp rate
is same as the value programmed in BUCKn_RATE, and the fastest rate is
10mv/us.
2nd method is gradual adjustment, adjust the voltage to a target value
step by step via i2c, each step is set to 100 mA. If you write the
voltage directly using an i2c write the rk808 will always ramp as fast
as it possibly can, about 100mv/us.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The LDOs are documented in the rk808 datasheet to have a soft start
time of 400us. Add that to the driver. If this time takes longer on
a certain board the device tree should be able to override with
"regulator-enable-ramp-delay".
This fixes some dw_mmc probing problems (together with other patches
posted to the mmc maiing lists) on rk3288.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Fixes the following sparse warnings:
drivers/regulator/rk808-regulator.c💯5: warning:
symbol 'rk808_set_suspend_voltage' was not declared. Should it be static?
drivers/regulator/rk808-regulator.c:115:5: warning:
symbol 'rk808_set_suspend_enable' was not declared. Should it be static?
drivers/regulator/rk808-regulator.c:126:5: warning:
symbol 'rk808_set_suspend_disable' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@kernel.org>
support setting suspend voltage and disable regulator in suspend.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The min_uv in DCDC1 & DCDC2 should be 712.5mv
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Reviwed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
On rk808 buck1 and buck2 have programmable ramp delays. Let's add a
function to allow a client of rk808 to set them.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
1. Pass &pdev->dev rather than &client->dev to of_regulator_match, the *dev
argument is used for devres to ensure devm_of_regulator_put_matches() will
be called when unload the module.
2. of_get_child_by_name() returns a node pointer with refcount incremented.
Thus add missing of_node_put(reg_np).
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The original RK808 regulator driver didn't setup input supplies
properly. Add them.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The min_sel is 0, max_sel is 15, so n_voltages should be 16.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The memory allocated in rk808_regulator_probe() needs to be freed when the
module is unloaded. Thus pass &pdev->dev rather than &client->dev to
devm_kzalloc.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
remove the redundant code, since pdata has been removed from stuct rk808
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The "dev" has been deleted from "struct rk808" in rk808 mfd driver
so rk808->dev should be replaced by &client->dev here.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The RK808 regulator driver was putting its config on the stack but not
initting it. That means that you got a semi-random config. Fix this.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The regulator module consists of 4 DCDCs, 8 LDOs and 2 switches.
The output voltages are configurable and are meant to supply power
to the main processor and other components
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Elaine Zhang