The bcm43430a0 and bcm43430a1 BT does not support the 0xfc45 command
to set the UART clock to 48 MHz and it also does not work at 4000000
baud without this command as some newer models do.
These chips are found on ACPI/x86 devices where the operating baudrate
does not come from the firmware but is hardcoded at 4000000, which does
not work.
Add a max_baudrate value to struct bcm_device_data and set this
to 2000000 on all known ACPI hardware-ids for the bcm43430a0
and the bcm43430a1.
Note this also adds the BCM2E9F ACPI HID which was missing until now.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
On some devices the BCM Bluetooth adapter does not have a valid bdaddr set.
btbcm.c currently sets HCI_QUIRK_INVALID_BDADDR to indicate when this is
the case. But this requires users to manual setup a btaddr, by doing e.g.:
btmgmt -i hci0 public-addr 'B0:F1:EC:82:1D:B3'
Which means that Bluetooth will not work out of the box on such devices.
To avoid this (where possible) hci_bcm sets: HCI_QUIRK_USE_BDADDR_PROPERTY
which tries to get the bdaddr from devicetree.
But this only works on devicetree platforms. On UEFI based platforms
there is a special Broadcom UEFI variable which when present contains
the devices bdaddr, just like how there is another UEFI variable which
contains wifi nvram contents including the wifi MAC address.
Add support for getting the bdaddr from this Broadcom UEFI variable,
so that Bluetooth will work OOTB for users on devices where this
UEFI variable is present.
This fixes Bluetooth not working on for example Asus T100HA 2-in-1s.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
As shown in the schematic diagram below.There may be a critical
scenario in the current code. If the device does not receive an
pure ack sent by the host due to insufficient receive buffer or
other reasons and triggers a retransmission, the host will always
be in an 'out-of-order' state.The state machine will get stuck.
host device
SEQ3,ACK4 --------->
<--------- SEQ4,ACK4
pure ACK ---------> (not received)
(out-of-order) <--------- SEQ4,ACK4(retransmission)
........
(out-of-order) <--------- SEQ4,ACK4(retransmission)
According to the description in the core specification: "whenever
a reliable packet is received, an acknowledgment shall be generated."
So set H5_TX_ACK_REQ bit to trigger retransmission of pure ack packet
when "out-of-order" occurs.
Signed-off-by: Qiqi Zhang <eddy.zhang@rock-chips.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This enables 2M and Coded PHY by default if they are marked as supported
in the LE features bits.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Split bt_iso_qos into dedicated unicast and broadcast
structures and add additional broadcast parameters.
Fixes: eca0ae4aea ("Bluetooth: Add initial implementation of BIS connections")
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Intercept debug exception events from the controller and put them into
a devcoredump using hci devcoredump APIs. The debug exception contains
data in a TLV format and it will be parsed in userspace.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Chethan Tumkur Narayan <chethan.tumkur.narayan@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch implements the btusb driver side .coredump() callback to
trigger a devcoredump via sysfs.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add devcoredump support for vhci that creates forcce_devcoredump debugfs
entry. This is used for mgmt-tester tests.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add devcoredump APIs to hci core so that drivers only have to provide
the dump skbs instead of managing the synchronization and timeouts.
The devcoredump APIs should be used in the following manner:
- hci_devcoredump_init is called to allocate the dump.
- hci_devcoredump_append is called to append any skbs with dump data
OR hci_devcoredump_append_pattern is called to insert a pattern.
- hci_devcoredump_complete is called when all dump packets have been
sent OR hci_devcoredump_abort is called to indicate an error and
cancel an ongoing dump collection.
The high level APIs just prepare some skbs with the appropriate data and
queue it for the dump to process. Packets part of the crashdump can be
intercepted in the driver in interrupt context and forwarded directly to
the devcoredump APIs.
Internally, there are 5 states for the dump: idle, active, complete,
abort and timeout. A devcoredump will only be in active state after it
has been initialized. Once active, it accepts data to be appended,
patterns to be inserted (i.e. memset) and a completion event or an abort
event to generate a devcoredump. The timeout is initialized at the same
time the dump is initialized (defaulting to 10s) and will be cleared
either when the timeout occurs or the dump is complete or aborted.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Basically all Intel controllers support both Central/Peripheral
LE states.
This patch enables the LE States quirk by default on all
Solar and Magnertor Intel controllers.
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add regulators, GPIOs and changes required to power on/off wcn6855.
Add support for firmware download for wcn6855 which is in the
linux-firmware repository as hpbtfw21.tlv and hpnv21.bin.
Based on the assumption that this is similar to the wcn6750
Tested-on: BTFW.HSP.2.1.0-00538-VER_PATCHZ-1
Signed-off-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Tested-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add bindings for the QTI WCN6855 chipset.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The btrtl_set_quirks() has accessed btrtl_dev->ic_info->lmp_subver since
b8e482d02513. However, if installing a Realtek Bluetooth controller
without the driver supported, it will hit the NULL point accessed.
Add a check for NULL to avoid the Kernel Oops.
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The driver needs both CRC32 and CRC8 to link correctly:
ld: drivers/bluetooth/btnxpuart.o: in function `nxp_serdev_probe':
drivers/bluetooth/btnxpuart.c:1214: undefined reference to
`crc8_populate_msb'
ld: drivers/bluetooth/btnxpuart.o: in function `nxp_send_ack':
drivers/bluetooth/btnxpuart.c:559: undefined reference to `crc8'
ld: drivers/bluetooth/btnxpuart.c:559: undefined reference to `crc8'
Fixes: 3e662aa4453a ("Bluetooth: NXP: Add protocol support for NXP Bluetooth chipsets")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds a driver based on serdev driver for the NXP BT serial protocol
based on running H:4, which can enable the built-in Bluetooth device
inside an NXP BT chip.
This driver has Power Save feature that will put the chip into sleep state
whenever there is no activity for 2000ms, and will be woken up when any
activity is to be initiated over UART.
This driver enables the power save feature by default by sending the vendor
specific commands to the chip during setup.
During setup, the driver checks if a FW is already running on the chip
by waiting for the bootloader signature, and downloads device specific FW
file into the chip over UART if bootloader signature is received..
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add binding document for NXP bluetooth chipsets attached over UART.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Adds serdev_device_break_ctl() and an implementation for ttyport.
This function simply calls the break_ctl in tty layer, which can
assert a break signal over UART-TX line, if the tty and the
underlying platform and UART peripheral supports this operation.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This replaces all instances of ENOTSUPP with EOPNOTSUPP since ENOTSUPP
is not a standard error code. This will help maintain consistency in
error codes when new serdev API's are added.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
tty_set_termios() never returns anything else than 0. Make the debug
prints to look directly into the new termios instead to check CRTSCTS
state.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add two more quirks to resume the device initialization and basic
operation as the device seems not to support "Read Transmit Power"
and "Set Extended Scan Parameters".
< HCI Command: LE Read Transmit Power (0x08|0x004b) plen 0
> HCI Event: Command Status (0x0f) plen 4
LE Read Transmit Power (0x08|0x004b) ncmd 1
Status: Unknown HCI Command (0x01)
< HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 8
Own address type: Random (0x01)
Filter policy: Accept all advertisement (0x00)
PHYs: 0x01
Entry 0: LE 1M
Type: Active (0x01)
Interval: 11.250 msec (0x0012)
Window: 11.250 msec (0x0012)
> HCI Event: Command Status (0x0f) plen 4
LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1
Status: Unknown HCI Command (0x01)
Signed-off-by: Raul Cheleguini <rcheleguini@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The Realtek RTL8723CS is a SDIO WiFi chip. It also contains a Bluetooth
module which is connected via UART to the host.
It shares lmp subversion with 8703B, so Realtek's userspace
initialization tool (rtk_hciattach) differentiates varieties of RTL8723CS
(CG, VF, XX) with RTL8703B using vendor's command to read chip type.
Also this chip declares support for some features it doesn't support
so add a quirk to indicate that these features are broken.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Bastian Germann <bage@debian.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Some adapters (e.g. RTL8723CS) advertise that they have more than
2 pages for local ext features, but they don't support any features
declared in these pages. RTL8723CS reports max_page = 2 and declares
support for sync train and secure connection, but it responds with
either garbage or with error in status on corresponding commands.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Bastian Germann <bage@debian.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/bluetooth/btmtkuart.c:971:36: error: ‘mt7668_data’ defined
but not used [-Werror=unused-const-variable=]
drivers/bluetooth/btmtkuart.c:966:36: error: ‘mt7663_data’ defined
but not used [-Werror=unused-const-variable=]
drivers/bluetooth/btmtkuart.c:962:36: error: ‘mt7622_data’ defined
but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/bluetooth/hci_qca.c:1869:37: error: ‘qca_soc_data_wcn6750’
defined but not used [-Werror=unused-const-variable=]
drivers/bluetooth/hci_qca.c:1853:37: error: ‘qca_soc_data_wcn3998’
defined but not used [-Werror=unused-const-variable=]
drivers/bluetooth/hci_qca.c:1841:37: error: ‘qca_soc_data_wcn3991’
defined but not used [-Werror=unused-const-variable=]
drivers/bluetooth/hci_qca.c:1830:37: error: ‘qca_soc_data_wcn3990’
defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/bluetooth/btmrvl_sdio.c:43:34: error:
‘btmrvl_sdio_of_match_table’ defined but not used
[-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here).
drivers/bluetooth/hci_ll.c:769:34: error: ‘hci_ti_of_match’ defined
but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This delays the identity address updates to give time for userspace to
process the new address otherwise there is a risk that userspace
creates a duplicated device if the MGMT event is delayed for some
reason.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This removes the following duplicate statement in
hci_le_ext_directed_advertising_sync():
cp.own_addr_type = own_addr_type;
Signed-off-by: Inga Stotland <inga.stotland@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The msft_set_filter_enable() command was using the deprecated
hci_request mechanism rather than hci_sync. This caused the warning error:
hci0: HCI_REQ-0xfcf0
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Currently, when we initiate disconnection, we will wait for the peer's
reply unless when we are suspending, where we fire and forget the
disconnect request.
A similar case is when adapter is powering off. However, we still wait
for the peer's reply in this case. Therefore, if the peer is
unresponsive, the command will time out and the power off sequence
will fail, causing "bluetooth powered on by itself" to users.
This patch makes the host doesn't wait for the peer's reply when the
disconnection reason is powering off.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Update the compatible for the Realtek RTL8821CS bluetooth node.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
RTL8821CS is a WiFi + Bluetooth combo chip from Realtek that provides
WiFi A/B/G/N/AC over an SDIO interface and Bluetooth 4.2 over a UART
interface.
Note that the firmware this was tested with was firmware version
0x75b8f098.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add compatible string for RTL8821CS for existing Realtek Bluetooth
driver.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Alistair Francis <alistair@alistair23.me>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fixes the following new warning:
net/bluetooth/hci_sync.c:2403 hci_pause_addr_resolution() warn: missing
error code? 'err'
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/202302251952.xryXOegd-lkp@intel.com/
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This makes hci_conn_hash_add append to the tail of the conn_hash so it
matches the order they are created, this is required if the controller
attempts to match the order of ACL with CIS which uses append logic
when programming the CIS ids on the CIG.
The result of this change affects Create CIS:
Before:
< HCI Command: LE Create Connected Isochronous Stream (0x08|0x0064) plen 9
Number of CIS: 2
CIS Handle: 2560
ACL Handle: 3586
CIS Handle: 2561
ACL Handle: 3585
After:
< HCI Command: LE Create Connected Isochronous Stream (0x08|0x0064) plen 9
Number of CIS: 2
CIS Handle: 2560
ACL Handle: 3585
CIS Handle: 2561
ACL Handle: 3586
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add the support for RTL8852BS BT controller on UART interface.
The necessary firmware file will be submitted to linux-firmware.
Signed-off-by: Victor Hassan <victor@allwinnertech.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add serdev support for the 88W8997 from NXP (previously Marvell). It
includes support for changing the baud rate. The command to change the
baud rate is taken from the user manual UM11483 Rev. 9 in section 7
(Bring-up of Bluetooth interfaces) from NXP.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use the maybe_unused macro for the device tree ids instead of #ifdef
CONFIG_OF. This makes it easier to add support for new devices.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The 88W8997 bluetooth module supports setting the max-speed property.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Update the documentation with the device tree binding for the Marvell
88W8997 bluetooth device.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Remove hardcoded interface number check because Bluetooth specification
since version 4.0 only recommends and no longer requires specific
interface numbers.
While earlier Bluetooth versions, i.e. 2.1 + EDR and 3.0 + HS, contain
required configuration table in Volume 4 - Host Controller Interface
Part B - USB Transport Layer, Bluetooth Core Specification Addendum 2
changes the table from required to recommended configuration.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This makes use of BIT macro when defining bitfields which makes it
clearer what bit it is toggling.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Pedro Tammela says:
====================
net/sched: act_pedit: minor improvements
This series aims to improve the code and usability of act_pedit for
netlink users.
Patches 1-2 improves error reporting for extended keys parsing with extack.
Patch 3 checks the static offsets a priori on create/update. Currently,
this is done at the datapath for both static and runtime offsets.
Patch 4 removes a check from the datapath which is redundant since the
netlink parsing validates the key types.
Patch 5 changes the 'pr_info()' calls in the datapath to rate limited
versions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Unbounded info messages in the pedit datapath can flood the printk
ring buffer quite easily depending on the action created.
As these messages are informational, usually printing some, not all,
is enough to bring attention to the real issue.
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netlink parsing already validates the key 'htype'.
Remove the datapath check as it's redundant.
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Static key offsets should always be on 32 bit boundaries. Validate them on
create/update time for static offsets and move the datapath validation
for runtime offsets only.
iproute2 already errors out if a given offset and data size cannot be
packed to a 32 bit boundary. This change will make sure users which
create/update pedit instances directly via netlink also error out,
instead of finding out when packets are traversing.
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hans de Goede