Currently we reset the key for each segment fed to the xcrypt instructions.
This patch optimises this for CBC and ECB so that we only do this once for
each encrypt/decrypt operation.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
With the impending addition of the givcipher type, both blkcipher and
ablkcipher algorithms will use it to create givcipher objects. As such
it no longer makes sense to split the system between ablkcipher and
blkcipher. In particular, both ablkcipher.c and blkcipher.c would need
to use the givcipher type which has to reside in ablkcipher.c since it
shares much code with it.
This patch merges the two Kconfig options as well as the modules into one.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
crypto_blkcipher_decrypt is wrong because it does not care about
the IV.
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There is no reason to keep the IV in the private structre. Instead keep
just a pointer to make the patch smaller :)
This also remove a few memcpy()s
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The current PLL initalization has a number of deficiencies:
- uses fixed multiplier of 8, which overclocks the chip when using a
reference clock that operates at frequencies above 33MHz. According
to a comment in the BSD source, this is true for the external clock
on almost all every board.
- writes to a reserved bit
- doesn't follow the initialization procedure specified in chapter
6.11.1 of the HIFN hardware users guide
- doesn't allow to use the PCI clock
This patch adds a module parameter to specify the reference clock
(pci or external) and its frequency and uses that to calculate the
optimum multiplier to reach the maximal speed. By default it uses
the external clock and assumes a speed of 66MHz, which effectively
halfs the frequency currently used.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Up until now we have ablkcipher algorithms have been identified as
type BLKCIPHER with the ASYNC bit set. This is suboptimal because
ablkcipher refers to two things. On the one hand it refers to the
top-level ablkcipher interface with requests. On the other hand it
refers to and algorithm type underneath.
As it is you cannot request a synchronous block cipher algorithm
with the ablkcipher interface on top. This is a problem because
we want to be able to eventually phase out the blkcipher top-level
interface.
This patch fixes this by making ABLKCIPHER its own type, just as
we have distinct types for HASH and DIGEST. The type it associated
with the algorithm implementation only.
Which top-level interface is used for synchronous block ciphers is
then determined by the mask that's used. If it's a specific mask
then the old blkcipher interface is given, otherwise we go with the
new ablkcipher interface.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
alpha:
drivers/crypto/hifn_795x.c: In function 'ablkcipher_walk_init':
drivers/crypto/hifn_795x.c:1231: error: implicit declaration of function 'sg_init_table'
drivers/crypto/hifn_795x.c:1243: error: implicit declaration of function 'sg_set_page'
drivers/crypto/hifn_795x.c: In function 'ablkcipher_walk_exit':
drivers/crypto/hifn_795x.c:1257: error: implicit declaration of function 'sg_page'
drivers/crypto/hifn_795x.c:1257: warning: passing argument 1 of '__free_pages' makes pointer from integer without a cast
drivers/crypto/hifn_795x.c: In function 'ablkcipher_add':
drivers/crypto/hifn_795x.c:1278: warning: passing argument 1 of 'kmap_atomic' makes pointer from integer without a cast
drivers/crypto/hifn_795x.c: In function 'ablkcipher_walk':
drivers/crypto/hifn_795x.c:1336: warning: passing argument 1 of 'kmap_atomic' makes pointer from integer without a cast
drivers/crypto/hifn_795x.c: In function 'hifn_setup_session':
drivers/crypto/hifn_795x.c:1465: warning: assignment makes pointer from integer without a cast
drivers/crypto/hifn_795x.c:1469: warning: assignment makes pointer from integer without a cast
drivers/crypto/hifn_795x.c:1472: warning: assignment makes pointer from integer without a cast
drivers/crypto/hifn_795x.c: In function 'ablkcipher_get':
drivers/crypto/hifn_795x.c:1593: warning: passing argument 1 of 'kmap_atomic' makes pointer from integer without a cast
{standard input}: Assembler messages:
{standard input}:7: Warning: setting incorrect section attributes for .got
drivers/crypto/hifn_795x.c: In function 'hifn_process_ready':
drivers/crypto/hifn_795x.c:1653: warning: passing argument 1 of 'kmap_atomic' makes pointer from integer without a cast
drivers/crypto/hifn_795x.c: In function 'hifn_probe':
drivers/crypto/hifn_795x.c:2438: error: 'DMA_32BIT_MASK' undeclared (first use in this function)
drivers/crypto/hifn_795x.c:2438: error: (Each undeclared identifier is reported only once
drivers/crypto/hifn_795x.c:2438: error: for each function it appears in.)
drivers/crypto/hifn_795x.c:2443: warning: format '%d' expects type 'int', but argument 4 has type 'long int'
drivers/crypto/hifn_795x.c:2443: warning: format '%d' expects type 'int', but argument 4 has type 'long int'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The HIFN driver is currently selectable on s390 but wont compile.
Since it looks like HIFN needs PCI make the Kconfig dependent on PCI,
which is not available on s390.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch forces HIFN driver to invoke crypto request callbacks from
tasklet (softirq context) instead of hardirq context, since network
stack expects it to be called from bottom halves.
It is done by simply scheduling callback invocation via dedicated
tasklet. Workqueue solution was dropped because of tooo slow
rescheduling performance (7 times slower than tasklet, for mode details
one can check this link:
http://tservice.net.ru/~s0mbre/blog/devel/other/2007_11_09.html).
Driver passed all AES and DES tests in tcryt.c module.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The Geode AES crypto engine supports only 128 bit long key. This
patch adds fallback for other key sizes which are required by the
AES standard.
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch moves macros in geode-aes.c into geode-aes.h.
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The code waits in a busy loop until the hardware finishes the encryption
or decryption process. This wants a cpu_relax() :)
The busy loop finishes either if the encryption is done or if the counter
is zero. If the latter is true than the hardware failed. Since this
should not happen, leave sith a BUG().
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
It is enough if the IV is copied before and after the while loop.
With DM-Crypt is seems not be required to save the IV after encrytion
because a new one is used in the request (dunno about other users).
It is not save to load the IV within while loop and not save afterwards
because we mill end up with the wrong IV if the request goes consists
of more than one page.
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This three defines are used in all AES related hardware.
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
alias isn't required because the module provides PCI ids.
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
HIFN driver update to use DES weak key checks (exported in this patch).
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This is a driver for HIFN 795x crypto accelerator chips.
It passed all tests for AES, DES and DES3_EDE except weak test for DES,
since hardware can not determine weak keys.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The previous patch fixed spurious read faults from occuring by copying
the data if we happen to have a single block at the end of a page. It
appears that gcc cannot guarantee 16-byte alignment in the kernel with
__attribute__. The following report from Torben Viets shows a buffer
that's only 8-byte aligned:
> eneral protection fault: 0000 [#1]
> Modules linked in: xt_TCPMSS xt_tcpmss iptable_mangle ipt_MASQUERADE
> xt_tcpudp xt_mark xt_state iptable_nat nf_nat nf_conntrack_ipv4
> iptable_filter ip_tables x_tables pppoe pppox af_packet ppp_generic slhc
> aes_i586
> CPU: 0
> EIP: 0060:[<c035b828>] Not tainted VLI
> EFLAGS: 00010292 (2.6.23.12 #7)
> EIP is at aes_crypt_copy+0x28/0x40
> eax: f7639ff0 ebx: f6c24050 ecx: 00000001 edx: f6c24030
> esi: f7e89dc8 edi: f7639ff0 ebp: 00010000 esp: f7e89dc8
Since the hardware must have 16-byte alignment, the following patch fixes
this by open coding the alignment adjustment.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The xcryptecb instruction always processes an even number of blocks so
we need to ensure th existence of an extra block if we have to process
an odd number of blocks.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The previous commit ("uml: keep UML Kconfig in sync with x86") is not
enough, unfortunately. If we go that way, we need to add dependencies
on !UML for several options.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the Geode AES module fails to encrypt or decrypt if
the coherent bits are not set what is currently the case if the
encryption does not occur inplace. However, the encryption works
on my Geode machine _only_ if the coherent bits are always set.
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch fixes the errors made in the users of the crypto layer during
the sg_init_table conversion. It also adds a few conversions that were
missing altogether.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are currently several SHA implementations that all define their own
initialization vectors and size values. Since this values are idential
move them to a header file under include/crypto.
Signed-off-by: Jan Glauber <jang@de.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Loading the crypto algorithm by the alias instead of by module directly
has the advantage that all possible implementations of this algorithm
are loaded automatically and the crypto API can choose the best one
depending on its priority.
Additionally it ensures that the generic implementation as well as the
HW driver (if available) is loaded in case the HW driver needs the
generic version as fallback in corner cases.
Also remove the probe for sha1 in padlock's init code.
Quote from Herbert:
The probe is actually pointless since we can always probe when
the algorithm is actually used which does not lead to dead-locks
like this.
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Loading the crypto algorithm by the alias instead of by module directly
has the advantage that all possible implementations of this algorithm
are loaded automatically and the crypto API can choose the best one
depending on its priority.
Additionally it ensures that the generic implementation as well as the
HW driver (if available) is loaded in case the HW driver needs the
generic version as fallback in corner cases.
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow in-place crypto operations. Also remove the coherent user flag
(we use it automagically now), and by default use the user written
key rather then the HW hidden key - this makes crypto just work without
any special considerations, and thats OK, since its our only usage
model.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Turning it into a boolean was unnecessary and caused ALGAPI to be
pinned down as a boolean to. This patch makes it a tristate again.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Disband drivers/s390/Kconfig, use the common Kconfig files. The s390
specific config options from drivers/s390/Kconfig are moved to the
respective common Kconfig files.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When this is compiled in it is run too early to do anything useful:
[ 6.052000] padlock: No VIA PadLock drivers have been loaded.
[ 6.052000] padlock: Using VIA PadLock ACE for AES algorithm.
[ 6.052000] padlock: Using VIA PadLock ACE for SHA1/SHA256 algorithms.
When it's a module it isn't doing anything special, the same functionality
can be provided in userspace by "probeall padlock padlock-aes padlock-sha"
in modules.conf if it is required.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: Michal Ludvig <michal@logix.cz>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace uses of the obsolete pci_module_init function.
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Starting with the z9 the CPU Cryptographic Assist Facility comes with
an integrated Pseudo Random Number Generator. The generator creates
random numbers by an algorithm similar to the ANSI X9.17 standard.
The pseudo-random numbers can be accessed via a character device driver
node called /dev/prandom. Similar to /dev/urandom any amount of bytes
can be read from the device without blocking.
Signed-off-by: Jan Glauber <jan.glauber@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This driver seems to be for a PCI device.
drivers/crypto/geode-aes.c:384: warning: implicit declaration of function 'pci_release_regions'
drivers/crypto/geode-aes.c:397: warning: implicit declaration of function 'pci_request_regions'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On Tue, Nov 14, 2006 at 01:41:25AM -0800, Andrew Morton wrote:
>...
> Changes since 2.6.19-rc5-mm2:
>...
> git-cryptodev.patch
>...
> git trees
>...
This patch makes the needlessly global geode_aes_crypt() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add a driver to support the AES hardware on the Geode LX processor.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch converts padlock-sha to use crypto_hash for its fallback.
It also changes the fallback selection to use selection by type instead
of name. This is done through the new CRYPTO_ALG_NEED_FALLBACK bit,
which is set if and only if an algorithm needs a fallback of the same
type.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch removes obsolete block operations of the simple cipher type
from drivers. These were preserved so that existing users can make a
smooth transition. Now that the transition is complete, they are no
longer needed.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds block cipher algorithms for cbc(aes) and ecb(aes) for
the PadLock device. Once all users to the old cipher type have been
converted the old cbc/ecb PadLock operations will be removed.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Now that the tfm is passed directly to setkey instead of the ctx, we no
longer need to pass the &tfm->crt_flags pointer.
This patch also gets rid of a few unnecessary checks on the key length
for ciphers as the cipher layer guarantees that the key length is within
the bounds specified by the algorithm.
Rather than testing dia_setkey every time, this patch does it only once
during crypto_alloc_tfm. The redundant check from crypto_digest_setkey
is also removed.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
TFMs are local variables. No need to declare them
static. After all one is enough.
Signed-off-by: Michal Ludvig <michal@logix.cz>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Compile a helper module padlock.ko that will try
to autoload all configured padlock algorithms.
This also provides backward compatibility with
the ancient times before padlock.ko was renamed
to padlock-aes.ko
Signed-off-by: Michal Ludvig <michal@logix.cz>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch makes two needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Support for SHA1 / SHA256 algorithms in VIA C7 processors.
Signed-off-by: Michal Ludvig <michal@logix.cz>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
PADLOCK_CRA_PRIORITY is shared between padlock-aes and padlock-sha
so it should be in the header.
On the other hand "struct cword" is only used in padlock-aes.c
so it's unnecessary to have it in padlock.h
Signed-off-by: Michal Ludvig <michal@logix.cz>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Whenever we rename modules we should add an alias to ensure that existing
users can still locate the new module.
This patch also gets rid of the now unused module function prototypes from
padlock.h.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Merge padlock-generic.c into padlock-aes.c and compile
AES as a standalone module. We won't make a monolithic
padlock.ko with all supported algorithms, instead we'll
compile each driver into its own module.
Signed-off-by: Michal Ludvig <michal@logix.cz>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The crypto API is made up of the part facing users such as IPsec and the
low-level part which is used by cryptographic entities such as algorithms.
This patch splits out the latter so that the two APIs are more clearly
delineated. As a bonus the low-level API can now be modularised if all
algorithms are built as modules.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Herbert's patch 82062c72cd
in cryptodev-2.6 tree breaks alignment rules for PadLock
xcrypt instruction leading to General protection Oopses.
This patch fixes the problem.
Signed-off-by: Michal Ludvig <michal@logix.cz>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
i386 assembly has more compact instructions for accessing 7-bit offsets.
So by moving the large members to the end of the structure we can save
quite a bit of code size. This patch shaves about 10% or 300 bytes off
the padlock-aes file.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Up until now algorithms have been happy to get a context pointer since
they know everything that's in the tfm already (e.g., alignment, block
size).
However, once we have parameterised algorithms, such information will
be specific to each tfm. So the algorithm API needs to be changed to
pass the tfm structure instead of the context pointer.
This patch is basically a text substitution. The only tricky bit is
the assembly routines that need to get the context pointer offset
through asm-offsets.h.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Since tfm contexts can contain arbitrary types we should provide at least
natural alignment (__attribute__ ((__aligned__))) for them. In particular,
this is needed on the Xscale which is a 32-bit architecture with a u64 type
that requires 64-bit alignment. This problem was reported by Ronen Shitrit.
The crypto_tfm structure's size was 44 bytes on 32-bit architectures and
80 bytes on 64-bit architectures. So adding this requirement only means
that we have to add an extra 4 bytes on 32-bit architectures.
On i386 the natural alignment is 16 bytes which also benefits the VIA
Padlock as it no longer has to manually align its context structure to
128 bits.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
A typo crept into the le32_to_cpu patch which broke 256-bit keys
in the padlock driver. The following patch based on observations
by Michael Heyse fixes the problem.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As the Crypto API now allows multiple implementations to be registered
for the same algorithm, we no longer have to play tricks with Kconfig
to select the right AES implementation.
This patch sets the driver name and priority for all the AES
implementations and removes the Kconfig conditions on the C implementation
for AES.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
A lot of crypto code needs to read/write a 32-bit/64-bit words in a
specific gender. Many of them open code them by reading/writing one
byte at a time. This patch converts all the applicable usages over
to use the standard byte order macros.
This is based on a previous patch by Denis Vlasenko.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add CONFIG_X86_32 for i386. This allows selecting options that only apply
to 32-bit systems.
(X86 && !X86_64) becomes X86_32
(X86 || X86_64) becomes X86
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When the Padlock does CBC encryption, the memory pointed to by EAX is
not updated at all. Instead, it updates the value of EAX by pointing
it to the last block in the output. Therefore to maintain the correct
semantics we need to copy the IV.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch ensures that cit_iv is aligned according to cra_alignmask
by allocating it as part of the tfm structure. As a side effect the
crypto layer will also guarantee that the tfm ctx area has enough space
to be aligned by cra_alignmask. This allows us to remove the extra
space reservation from the Padlock driver.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
By operating on multiple blocks at once, we expect to extract more
performance out of the VIA Padlock.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the work done aes_padlock can be done in aes_set_key. This
means that we only have to do it once when the key changes rather
than every time we perform an encryption or decryption.
This patch also sets cra_alignmask to let the upper layer ensure
that the buffers fed to us are aligned correctly.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Alexey Dobriyan