Add a platform driver for Nouveau devices declared using the device tree
or platform data. This driver currently supports GK20A on Tegra
platforms and is only compiled for these platforms if Nouveau is
enabled.
Nouveau will probe the chip type itself using the BOOT0 register, so all
this driver really needs to do is to make sure the module is powered and
its clocks active before calling nouveau_drm_platform_probe().
Heavily based on work done by Thierry Reding.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
echo ac:id >> pstate # select mode when on mains power
echo dc:id >> pstate # select mode when on battery
echo id >> pstate # select mode for both
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
As a side note.. It's a bit hard to figure out how to name this commit..
GK20A is NVEA, which is before NV108 (GK208).. Confusing.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
As documented at:
ftp://download.nvidia.com/open-gpu-doc/gk104-disable-graphics-power-gating/1/gk104-disable-graphics-power-gating.txt
NVIDIA were not able document the steps necessary to detect whether this
is required or not at this time. However, they did confirm that this
procedure is safe to perform unconditionally on GK104/6. GK107 does not
have the power gating feature, and it was recommended that we do not
perform these steps there as the effects were not verified.
The disable path is from observing the binary driver, and not
documented in the link above.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Pull DRM updates from Dave Airlie:
"Like all good pull reqs this ends with a revert, so it must mean we
tested it,
[ Ed. That's _one_ way of looking at it ]
This pull is missing nouveau, Ben has been stuck trying to track down
a very longstanding bug that revealed itself due to some other
changes. I've asked him to send you a direct pull request for nouveau
once he cleans things up. I'm away until Monday so don't want to
delay things, you can make a decision on that when he sends it, I have
my phone so I can ack things just not really merge much.
It has one trivial conflict with your tree in armada_drv.c, and also
the pull request contains some component changes that are already in
your tree, the base tree from Russell went via Greg's tree already,
but some stuff still shows up in here that doesn't when I merge my
tree into yours.
Otherwise all pretty standard graphics fare, one new driver and
changes all over the place.
New drivers:
- sti kms driver for STMicroelectronics chipsets stih416 and stih407.
core:
- lots of cleanups to the drm core
- DP MST helper code merged
- universal cursor planes.
- render nodes enabled by default
panel:
- better panel interfaces
- new panel support
- non-continuous cock advertising ability
ttm:
- shrinker fixes
i915:
- hopefully ditched UMS support
- runtime pm fixes
- psr tracking and locking - now enabled by default
- userptr fixes
- backlight brightness fixes
- MST support merged
- runtime PM for dpms
- primary planes locking fixes
- gen8 hw semaphore support
- fbc fixes
- runtime PM on SOix sleep state hw.
- mmio base page flipping
- lots of vlv/chv fixes.
- universal cursor planes
radeon:
- Hawaii fixes
- display scalar support for non-fixed mode displays
- new firmware format support
- dpm on more asics by default
- GPUVM improvements
- uncached and wc GTT buffers
- BOs > visible VRAM
exynos:
- i80 interface support
- module auto-loading
- ipp driver consolidated.
armada:
- irq handling in crtc layer only
- crtc renumbering
- add component support
- DT interaction changes.
tegra:
- load as module fixes
- eDP bpp and sync polarity fixed
- DSI non-continuous clock mode support
- better support for importing buffers from nouveau
msm:
- mdp5/adq8084 v1.3 hw enablement
- devicetree clk changse
- ifc6410 board working
tda998x:
- component support
- DT documentation update
vmwgfx:
- fix compat shader namespace"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (551 commits)
Revert "drm: drop redundant drm_file->is_master"
drm/panel: simple: Use devm_gpiod_get_optional()
drm/dsi: Replace upcasting macro by function
drm/panel: ld9040: Replace upcasting macro by function
drm/exynos: dp: Modify driver to support drm_panel
drm/exynos: Move DP setup into commit()
drm/panel: simple: Add AUO B133HTN01 panel support
drm/panel: simple: Support delays in panel functions
drm/panel: simple: Add proper definition for prepare and unprepare
drm/panel: s6e8aa0: Add proper definition for prepare and unprepare
drm/panel: ld9040: Add proper definition for prepare and unprepare
drm/tegra: Add support for panel prepare and unprepare routines
drm/exynos: dsi: Add support for panel prepare and unprepare routines
drm/exynos: dpi: Add support for panel prepare and unprepare routines
drm/panel: simple: Add dummy prepare and unprepare routines
drm/panel: s6e8aa0: Add dummy prepare and unprepare routines
drm/panel: ld9040: Add dummy prepare and unprepare routines
drm/panel: Provide convenience wrapper for .get_modes()
drm/panel: add .prepare() and .unprepare() functions
drm/panel: simple: Remove simple-panel compatible
...
The final parameter to ttm_bo_reserve() is a pointer, therefore callers
should use NULL instead of 0.
Fixes a bunch of sparse warnings of this type:
warning: Using plain integer as NULL pointer
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
deadlock fix.
* 'linux-3.16' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/therm: fix a potential deadlock in the therm monitoring code
A couple of DP regression fixes, kepler memory reclocking fixes, and a fix for an annoying display issue that can pop up on resume.
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/ram: fix test for gpio presence
drm/nouveau/dp: workaround broken display
drm/nouveau/dp: fix required link bandwidth calculations
drm/nouveau/kms: restore fbcon after display has been resumed
drm/nv50-/kms: pass a non-zero value for head to sor dpms methods
drm/nouveau/fb: Prevent inlining of ramfuc_reg
drm/gk104/ram: bash mpll bit 31 on
This allows reservation objects to be used in dma-buf. it's required
for implementing polling support on the fences that belong to a dma-buf.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com> #drivers/media/v4l2-core/
Acked-by: Thomas Hellstrom <thellstrom@vmware.com> #drivers/gpu/drm/ttm
Acked-by: Sumit Semwal <sumit.semwal@linaro.org>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net> #drivers/gpu/drm/armada/
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The display in fdo#76483 pulses the hotplug line for link retraining
after we cut power to the main link on the source, even while it's
in D3.
fdo#76483
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Under some complicated circumstances (boot, suspend, resume, attach
second display, suspend, resume, suspend, detach second display,
resume, suspend, attach second display, resume), the fb_set_suspend()
call can somehow result in a modeset being attempted before we're
ready for it and things blow up in fun ways.
Running display init first fixes the issue.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There's Apple machines out there which (probably completely arbitrarily)
restrict each output path to a particular head. This causes us to not
be able to locate the output data needed to power on/off the DP output
correctly.
We fix this by passing in a head index we know is valid (as opposed to
"head 0").
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
When gcc 4.8 inlines this function, it eats up 16 bytes on the stack
every time. Eventually we hit warnings because our stack grew too
much:
ramnve0.c:1383:1: error: the frame size of 1496 bytes is larger than
1024 bytes
We fix this by preventing inlining for this function.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
To implement hotplug detection in a race-free manner, drivers must call
drm_kms_helper_poll_init() before hotplug events can be triggered. Such
events can be triggered right after any of the encoders or connectors
are initialized. At the same time, if the drm_fb_helper_hotplug_event()
helper is used by a driver, then the poll helper requires some parts of
the FB helper to be initialized to prevent a crash.
At the same time, drm_fb_helper_init() requires information that is not
necessarily available at such an early stage (number of CRTCs and
connectors), so it cannot be used yet.
Add a new helper, drm_fb_helper_prepare(), that initializes the bare
minimum needed to allow drm_kms_helper_poll_init() to execute and any
subsequent hotplug events to be processed properly.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There's no need for this to be modifiable. Make it const so that it can
be put into the .rodata section.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
bo->mem.placement is not initialized when ttm_bo_man_get_node is called,
so the flag had no effect at all.
v2: change nouveau and vmwgfx as well
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
misc core patches picked up by Daniel and Jani.
* tag 'topic/core-stuff-2014-06-30' of git://anongit.freedesktop.org/drm-intel:
drm/fb-helper: Remove unnecessary list empty check in drm_fb_helper_debug_enter()
drm/fb-helper: Redundant info->fix.type_aux setting in drm_fb_helper_fill_fix()
drm/debugfs: add an "edid_override" file per connector
drm/debugfs: add a "force" file per connector
drm: add register and unregister functions for connectors
drm: fix uninitialized acquire_ctx fields (v2)
drm: Driver-specific ioctls range from 0x40 to 0x9f
drm: Don't export internal module variables
Introduce generic functions to register and unregister connectors. This
provides a common place to add and remove associated user space
interfaces.
Signed-off-by: Thomas Wood <thomas.wood@intel.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
couple more DP regression fixes.
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/disp: fix oops in destructor with headless cards
drm/gf117/i2c: no aux channels on this chipset
If init doesn't run then disp->outp might not be initialized, resulting
in an oops.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This is bigger because it regenerates the internal firmwares after a fix.
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/doc: update the thermal documentation
drm/nouveau/pwr: fix typo in fifo wrap handling
drm/nv50/disp: fix a potential oops in supervisor handling
drm/nouveau/disp/dp: don't touch link config after success
drm/nouveau/kms: reference vblank for crtc during pageflip.
drm/gk104/fb/ram: fixups from an earlier search+replace
drm/nv50/gr: remove an unneeded write while initialising PGRAPH
drm/nv50/gr: fix overlap while zeroing zcull regions
drm/gf100-/gr: report class data to host on fwmthd failure
drm/gk104/ibus: increase various random timeouts
drm/gk104/clk: only touch divider for mode we'll be using
Need to drm_vblank_get/put() the crtc involved in a
pending pageflip, or we might not get vblank irqs and
updates of vblank counts and timestamps for pageflip
events and flip completion.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
The blob does not seem to write at that place for my NVAC, though it
does for my NV96, agreeing with what is done in the if/else structure
below. I guess someone forgot to remove the line when the if/else was
put in place.
Signed-off-by: Pierre Moreau <pierre.morrow@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The specified stride was not correct, resulting in erases overlapping
and part of the zcull regions being not erased at all.
Signed-off-by: Pierre Moreau <pierre.morrow@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes (at least) PTHERM accesses timing out at higher clock speeds.
Values and registers taken from what the binary driver does.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Pull drm updates from Dave Airlie:
"This is the main drm merge window pull request, changes all over the
place, mostly normal levels of churn.
Highlights:
Core drm:
More cleanups, fix race on connector/encoder naming, docs updates,
object locking rework in prep for atomic modeset
i915:
mipi DSI support, valleyview power fixes, cursor size fixes,
execlist refactoring, vblank improvements, userptr support, OOM
handling improvements
radeon:
GPUVM tuning and large page size support, gart fixes, deep color
HDMI support, HDMI audio cleanups
nouveau:
- displayport rework should fix lots of issues
- initial gk20a support
- gk110b support
- gk208 fixes
exynos:
probe order fixes, HDMI changes, IPP consolidation
msm:
debugfs updates, misc fixes
ast:
ast2400 support, sync with UMS driver
tegra:
cleanups, hdmi + hw cursor for Tegra 124.
panel:
fixes existing panels add some new ones.
ipuv3:
moved from staging to drivers/gpu"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (761 commits)
drm/nouveau/disp/dp: fix tmds passthrough on dp connector
drm/nouveau/dp: probe dpcd to determine connectedness
drm/nv50-: trigger update after all connectors disabled
drm/nv50-: prepare for attaching a SOR to multiple heads
drm/gf119-/disp: fix debug output on update failure
drm/nouveau/disp/dp: make use of postcursor when its available
drm/g94-/disp/dp: take max pullup value across all lanes
drm/nouveau/bios/dp: parse lane postcursor data
drm/nouveau/dp: fix support for dpms
drm/nouveau: register a drm_dp_aux channel for each dp connector
drm/g94-/disp: add method to power-off dp lanes
drm/nouveau/disp/dp: maintain link in response to hpd signal
drm/g94-/disp: bash and wait for something after changing lane power regs
drm/nouveau/disp/dp: split link config/power into two steps
drm/nv50/disp: train PIOR-attached DP from second supervisor
drm/nouveau/disp/dp: make use of existing output data for link training
drm/gf119/disp: start removing direct vbios parsing from supervisor
drm/nv50/disp: start removing direct vbios parsing from supervisor
drm/nouveau/disp/dp: maintain receiver caps in response to hpd signal
drm/nouveau/disp/dp: create subclass for dp outputs
...
display rework fixes lots of displayport issues.
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6: (43 commits)
drm/nouveau/disp/dp: fix tmds passthrough on dp connector
drm/nouveau/dp: probe dpcd to determine connectedness
drm/nv50-: trigger update after all connectors disabled
drm/nv50-: prepare for attaching a SOR to multiple heads
drm/gf119-/disp: fix debug output on update failure
drm/nouveau/disp/dp: make use of postcursor when its available
drm/g94-/disp/dp: take max pullup value across all lanes
drm/nouveau/bios/dp: parse lane postcursor data
drm/nouveau/dp: fix support for dpms
drm/nouveau: register a drm_dp_aux channel for each dp connector
drm/g94-/disp: add method to power-off dp lanes
drm/nouveau/disp/dp: maintain link in response to hpd signal
drm/g94-/disp: bash and wait for something after changing lane power regs
drm/nouveau/disp/dp: split link config/power into two steps
drm/nv50/disp: train PIOR-attached DP from second supervisor
drm/nouveau/disp/dp: make use of existing output data for link training
drm/gf119/disp: start removing direct vbios parsing from supervisor
drm/nv50/disp: start removing direct vbios parsing from supervisor
drm/nouveau/disp/dp: maintain receiver caps in response to hpd signal
drm/nouveau/disp/dp: create subclass for dp outputs
...
We were sending the necessary state changes to unset the mode, but
never actually hit the big GO button unless another modeset happens
afterwards.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
SOR_PWR has no effect to power-off DP links, unlike other SOR protocols.
Instead, on the source side, we cut power to the lanes after having put
the sink into D3. Link training takes care of everything required to
bring it back again.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This previously worked for the most part due to userspace doing a
modeset in response to HPD interrupts. This will allow us to
properly handle cases where sync is lost for other reasons, or if
userspace isn't caring.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This will, at some point, be used to replace various bits and pieces of
code doing direct bios parsing. For now, it'll just be used for some
DP improvements.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There's also provisions to allow a pad to be locked with a specific
routing, for an indefinite period of time. This will be used in
future patches.
The G94+ pad driver will now also power-down pads when not required.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This was a half-finished hack before, just enough to handle the shared
aux/i2c pad thing on G94 and up.
We got lucky with locking etc up until now, as this was (generally) all
protected by the DRM mode_config lock. It's about to become a lot more
likely to hit the races.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Re-uses the implementation's accessor functions rather than requiring
and init/fini implementation for each chipset.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There's really not a great deal this time due to me spending most of this window on Maxwell. But, here's the random bits and pieces that's currently queued.
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6: (25 commits)
drm/gk208/gr: add missing registers to grctx init
drm/nouveau/kms/nv04-nv40: fix pageflip events via special case.
drm/nv50-/mc: fix kms pageflip events by reordering irq handling order.
drm/nouveau/disp/nv04-nv40: abort scanoutpos query on vga analog.
drm/nv50-/kms: wait for enough ring space in crtc_prepare()
drm/nouveau/disp/dp: support training pattern 3
drm/nouveau/disp/dp: support aux read interval during link training
drm/gk104/gpio: fix incorrect interrupt register usage
drm/nouveau/core: punt all object state change messages to trace level
drm/nouveau/clk: allow end-user reclocking for nv40, nvaa, and nve0 clock types
drm/nouveau/fb: default NvMemExec to on, turning it off is used for debugging only
drm/nouveau/bios: fix a potential NULL deref in the PROM shadowing function
drm/nouveau/i2c: bump the i2c delay for the adt7473
drm/nouveau/therm/fan/tach: default to 2 pulses per revolution
drm/nvf0/device: enable video decoding engines on gk110/gk208
drm/nvf1/device: add support for 0xf1 (gk110b)
drm/nouveau/device: support for probing GK20A
drm/nouveau/graph: add GK20A support
drm/nouveau/graph: pad firmware code at load time
drm/nouveau/graph: enable when using external fw
...
This fixes hangs on GK208 which happen instantaneously on trying to use a
geometry shader.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org # v3.14+
Cards with nv04 display engine can't reliably use vblank
counts and timestamps computed via drm_handle_vblank(), as
the function gets invoked after sending the pageflip events.
Fix this by defaulting to the old crtcid = -1 fallback path
on <= NV-50 cards, and only using the precise path on NV-50
and later.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: <stable@vger.kernel.org> # 3.13+
Whenever a single nouveau_mc_intr() main gpu irq-handler invocation was
responsible for calling both, the vblank-irq handler (display engine irq)
and kms-pageflip completion handler (from fifo irq), the order of
invocation was wrong. nouveau_finish_flip() was called before
drm_handle_vblank() for the vblank of pageflip completion, so the
emitted pageflip event contained stale vblank count and timestamp
from previous vblank. This caused failure in userspace to timestamp
properly.
Reorder order of invocation of engine irq handlers: Put
NVDEV_ENGINE_DISP always on top, and thereby before NVDEV_ENGINE_FIFO,
so that drm_handle_vblank() gets called to update vblank timestamps
and count before potential pageflip events make use of that
information.
This works on nv-50 and later, where kms-pageflip completion triggers
an irq either after a separate vblank irq, or both pageflip and vblank
trigger one common irq invocation, but never before vblank irqs.
v2 (Ben):
- removed mods for nv04-nv40, it doesn't help there anyway
- this is considered a hack, and a better solution should be found
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: <stable@vger.kernel.org> # 3.13+
nv04_disp_scanoutpos() must abort to trigger simple timestamping
fallback if vtotal/htotal regs return zero. This happens if the
output isn't a digital output, but a vga analog output, as the
regs don't get initialized in that case.
Fixes timestamping failure on nv-40 and earlier with vga output.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: <stable@vger.kernel.org> # 3.14+
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Some adt7473 can't manage the 20µs delay we use for the bitbanging, bumping
it to 40µs seem to do the trick.
Signed-off-by: Martin Peres <martin.peres@free.fr>
Tested-by: Marcel Dopita <mdop@seznam.cz>
I spent some time this weekend trying to find in the vbios the number of
pulses per revolutions in the vbios but couldn't find it. It would seem
all my cards have 2 pulses per revolution so let's stick to that until
further notice.
Thermal table's id 0x48 may indicate this information but it would seem
that changing the value results in the blob power or clock gating the
RPM counter... We should ask NVIDIA about that, should be trivial-enough
for them to answer.
Signed-off-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Set the correct subdev/engine classes when GK20A (0xea) is probed.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Add a GR device for GK20A based on NVE4, with the correct classes
definitions (GK20A's 3D class is 0xa297).
Most of the NVE4 code can be used on GK20A, so make relevant bits of
NVE4 available to other chips as well.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Pad the microcode to a multiple of 0x40 words, otherwise firmware will
fail to run from non-prepadded firmware files.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
nvc0_graph_ctor() would only let the graphics engine be enabled if its
oclass has a proper microcode linked to it. This prevents GR from being
enabled at all on chips that rely exclusively on external firmware, even
though such a use-case is valid.
Relax the conditions enabling the GR engine to also include the case
where an external firmware has also been loaded.
Also switch to external firmware if the graph class has no microcode
linked to it.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
GK20A's FIFO is compatible with NVE0, but only features 128 channels and
1 runlist.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Add a simple FB device for GK20A, as well as a RAM implementation
suitable for chips that use system memory as video RAM.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Add support for initializing the priv ring of GK20A. This is done by the
BIOS on desktop GPUs, but needs to be done by hand on Tegra.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Adapt the NVC0 BAR driver to make it able to support chips that do not
expose a BAR3. When this happens, BAR1 is then used for USERD mapping
and the BAR alloc() functions is disabled, making GPU objects unable
to rely on BAR for data access and falling back to PRAMIN.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Some chips that use system memory exclusively (e.g. GK20A) do not
expose 2 BAR regions. For them only BAR1 exists, and it should be used
for USERD mapping. Do not map BAR3 if its resource does not exist.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
I cannot see a need to provide a DRM_ version of ARRAY_SIZE(), only used
in a few places. I suspect its usage has been spread by copy & paste
rather than anything else.
Let's just remove it for plain ARRAY_SIZE().
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
One small step after another, the never-ending crusade towards better
code continues.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Merge drm-fixes into drm-next.
Both i915 and radeon need this done for later patches.
Conflicts:
drivers/gpu/drm/drm_crtc_helper.c
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/i915_gem.c
drivers/gpu/drm/i915/i915_gem_execbuffer.c
drivers/gpu/drm/i915/i915_gem_gtt.c
* acpi-video:
ACPI / video: Add 4 new models to the use_native_backlight DMI list
ACPI / video: Add use native backlight quirk for the ThinkPad W530
ACPI / video: Unregister the backlight device if a raw one shows up later
backlight: Add backlight device (un)registration notification
nouveau: Don't check acpi_video_backlight_support() before registering backlight
acer-wmi: Add Aspire 5741 to video_vendor_dmi_table
acer-wmi: Switch to acpi_video_unregister_backlight
ACPI / video: Add an acpi_video_unregister_backlight function
ACPI / video: Don't register acpi_video_resume notifier without backlight devices
ACPI / video: change acpi-video brightness_switch_enabled default to 0
acpi_video_backlight_support() is supposed to be called by other (vendor
specific) firmware backlight controls, not by native / raw backlight controls
like nv_backlight.
Userspace will normally prefer firmware interfaces over raw interfaces, so
if acpi_video backlight support is present it will use that even if
nv_backlight is registered as well.
Except when video.use_native_backlight is present on the kernel cmdline
(or enabled through a dmi based quirk). As the name indicates the goal here
is to make only the raw interface available to userspace so that it will use
that (it only does this when it sees a win8 compliant bios).
This is done by:
1) Not registering any acpi_video# backlight devices; and
2) Making acpi_video_backlight_support() return true so that other firmware
drivers, ie acer_wmi, thinkpad_acpi, dell_laptop, etc. Don't register their
own vender specific interfaces.
Currently nouveau breaks this setup, as when acpi_video_backlight_support()
returns true, it does not register itself, resulting in no backlight control
at all.
This is esp. going to be a problem with 3.16 which will default to
video.use_native_backlight=1, and thus nouveau based laptops with a win8 bios
will get no backlight control at all.
This also likely explains why the previous attempt to make
video.use_native_backlight=1 the default was not a success, as without this
patch having a default of video.use_native_backlight=1 will cause regressions.
Note this effectively reverts commit 5bead799d3 (drm/nouveau: don't
expose backlight control when available through ACPI).
References: https://bugzilla.redhat.com/show_bug.cgi?id=1093171
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
fixes nasty panel bleeding bug.
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/gf119-/disp: fix nasty bug which can clobber SOR0's clock setup
drm/nvd9/therm: handle another kind of PWM fan
Fixes a LVDS bleed issue on Lenovo W530 that can occur under a
number of circumstances.
Cc: <stable@vger.kernel.org > # v3.9+
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
nouveau fixes.
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/gm107/gr: bump attrib cb size quite a bit
drm/nouveau: fix another lock unbalance in nouveau_crtc_page_flip
drm/nouveau/bios: fix shadowing from PROM on big-endian systems
drm/nouveau/acpi: allow non-optimus setups to load vbios from acpi
When initially looking at traces, missed the fact the binary driver was
using large pages.
Fixes page faults when launching geometry shaders.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes a regression introduced by 060810d7ab "drm/nouveau: fix locking
issues in page flipping paths". chan->cli->mutex is unlocked a second time
in the fail_unreserve path, fix this by moving mutex_unlock down.
Cc: stable@vger.kernel.org # v3.11+
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There appear to be a crop of new hardware where the vbios is not
available from PROM/PRAMIN, but there is a valid _ROM method in ACPI.
The data read from PCIROM almost invariably contains invalid
instructions (still has the x86 opcodes), which makes this a low-risk
way to try to obtain a valid vbios image.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76475
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: <stable@vger.kernel.org> # v2.6.35+
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
So I just wanted to add a new field to struct drm_device and
accidentally stumbled over something. According to comments
dev->open_count is protected by dev->count_lock, but that's totally
not the case. It's protected by drm_global_mutex.
Unfortunately the vga switcheroo callbacks took this comment at face
value. The problem is that we can't just take the drm_global_mutex
because:
- It would lead to a locking inversion with the driver load/unload
paths.
- It wouldn't actually protect anything, for that we'd need to wrap
the entire vga switcheroo code in the drm_global_mutex. And I'm not
sure whether that would actually solve anything.
What we probably want is a try_to_grab_switcheroo reference kind of
thing which is used in the driver's ->open callback. Then we could
move all that ->can_switch madness into the vga switcheroo core where
it really belongs.
But since that would amount to real work take the easy way out and
just add a comment. It's definitely not going to make anything worse
since doing switcheroo state changes while restarting X just isn't
recommended. Even though the delayed switching code does exactly that.
v2:
- Simplify the ->can_switch implementations more (Thierry)
- Fix comment about the dev->open_count locking (Thierry)
Cc: Thierry Reding <treding@nvidia.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> (v1)
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit 457e77b264 added two checks applied to a
value received from nv_rd32(bios, 0x619f04). But after this new piece of code
is executed, the addr local variable does not hold the same value it used to
hold before the commit. Here is what is was assigned in the original code:
(u64)(nv_rd32(bios, 0x619f04) & 0xffffff00) << 8
in the committed code it ends up with this value:
(u64)(nv_rd32(bios, 0x619f04) >> 8) << 8
These expressions are obviously not equivalent.
My Nvidia video card does not show anything on the display when I boot a
kernel containing this commit.
The patch fixes the code so that the new checks are still done, but the
side effect of an incorrect addr value is gone.
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Merge window -fixes pull request as usual. Well, I did sneak in Jani's
drm_i915_private_t typedef removal, need to have fun with a big sed job
too ;-)
Otherwise:
- hdmi interlaced fixes (Jesse&Ville)
- pipe error/underrun/crc tracking fixes, regression in late 3.14-rc (but
not cc: stable since only really relevant for igt runs)
- large cursor wm fixes (Chris)
- fix gpu turbo boost/throttle again, was getting stuck due to vlv rps
patches (Chris+Imre)
- fix runtime pm fallout (Paulo)
- bios framebuffer inherit fix (Chris)
- a few smaller things
* tag 'drm-intel-fixes-2014-04-04' of git://anongit.freedesktop.org/drm-intel: (196 commits)
Skip intel_crt_init for Dell XPS 8700
drm/i915: vlv: fix RPS interrupt mask setting
Revert "drm/i915/vlv: fixup DDR freq detection per Punit spec"
drm/i915: move power domain init earlier during system resume
drm/i915: Fix the computation of required fb size for pipe
drm/i915: don't get/put runtime PM at the debugfs forcewake file
drm/i915: fix WARNs when reading DDI state while suspended
drm/i915: don't read cursor registers on powered down pipes
drm/i915: get runtime PM at i915_display_info
drm/i915: don't read pp_ctrl_reg if we're suspended
drm/i915: get runtime PM at i915_reg_read_ioctl
drm/i915: don't schedule force_wake_timer at gen6_read
drm/i915: vlv: reserve the GT power context only once during driver init
drm/i915: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/overlay: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/ringbuffer: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/display: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/irq: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/gem: prefer struct drm_i915_private to drm_i915_private_t
drm/i915/dma: prefer struct drm_i915_private to drm_i915_private_t
...
Here's the latest iteration of the universal planes work, which I believe is
finally ready for merging. Aside from the minor driver patches to use the
new drm_for_each_legacy_plane() macro for plane loops, these should all have
an r-b from Rob Clark now.
Actual userspace-visibility is currently hidden behind a
drm.universal_planes module parameter so that we can do some experimental
testing of this before flipping it on universally.
* 'primary-plane' of git://people.freedesktop.org/~robclark/linux:
drm/doc: Update plane documentation and add plane helper library
drm: Allow userspace to ask for universal plane list (v2)
drm: Remove unused drm_crtc->fb
drm: Replace crtc fb with primary plane fb (v3)
drm/msm: Switch to universal plane API's
drm: Add drm_crtc_init_with_planes() (v2)
drm: Add plane type property (v2)
drm: Add drm_universal_plane_init()
drm: Add primary plane helpers (v3)
drm: Make drm_crtc_check_viewport non-static
drm/shmobile: Restrict plane loops to only operate on legacy planes
drm/i915: Restrict plane loops to only operate on overlay planes (v2)
drm/exynos: Restrict plane loops to only operate on overlay planes (v2)
drm: Add support for multiple plane types (v2)
This should ensure we don't hit a locking problem when someone
wakes us up via a connector, we should never go into suspend
while the display is on anyways.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Now that CRTC's have a primary plane, there's no need to track the
framebuffer in the CRTC. Replace all references to the CRTC fb with the
primary plane's fb.
This patch was generated by the Coccinelle semantic patching tool using
the following rules:
@@ struct drm_crtc C; @@
- (C).fb
+ C.primary->fb
@@ struct drm_crtc *C; @@
- (C)->fb
+ C->primary->fb
v3: Generate patch via coccinelle. Actual removal of crtc->fb has been
moved to a subsequent patch.
v2: Fixup several lingering crtc->fb instances that were missed in the
first patch iteration. [Rob Clark]
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
- Device PM QoS support for latency tolerance constraints on systems with
hardware interfaces allowing such constraints to be specified. That is
necessary to prevent hardware-driven power management from becoming
overly aggressive on some systems and to prevent power management
features leading to excessive latencies from being used in some cases.
- Consolidation of the handling of ACPI hotplug notifications for device
objects. This causes all device hotplug notifications to go through
the root notify handler (that was executed for all of them anyway
before) that propagates them to individual subsystems, if necessary,
by executing callbacks provided by those subsystems (those callbacks
are associated with struct acpi_device objects during device
enumeration). As a result, the code in question becomes both smaller
in size and more straightforward and all of those changes should not
affect users.
- ACPICA update, including fixes related to the handling of _PRT in cases
when it is broken and the addition of "Windows 2013" to the list of
supported "features" for _OSI (which is necessary to support systems
that work incorrectly or don't even boot without it). Changes from
Bob Moore and Lv Zheng.
- Consolidation of ACPI _OST handling from Jiang Liu.
- ACPI battery and AC fixes allowing unusual system configurations to
be handled by that code from Alexander Mezin.
- New device IDs for the ACPI LPSS driver from Chiau Ee Chew.
- ACPI fan and thermal optimizations related to system suspend and resume
from Aaron Lu.
- Cleanups related to ACPI video from Jean Delvare.
- Assorted ACPI fixes and cleanups from Al Stone, Hanjun Guo, Lan Tianyu,
Paul Bolle, Tomasz Nowicki.
- Intel RAPL (Running Average Power Limits) driver cleanups from Jacob Pan.
- intel_pstate fixes and cleanups from Dirk Brandewie.
- cpufreq fixes related to system suspend/resume handling from Viresh Kumar.
- cpufreq core fixes and cleanups from Viresh Kumar, Stratos Karafotis,
Saravana Kannan, Rashika Kheria, Joe Perches.
- cpufreq drivers updates from Viresh Kumar, Zhuoyu Zhang, Rob Herring.
- cpuidle fixes related to the menu governor from Tuukka Tikkanen.
- cpuidle fix related to coupled CPUs handling from Paul Burton.
- Asynchronous execution of all device suspend and resume callbacks,
except for ->prepare and ->complete, during system suspend and resume
from Chuansheng Liu.
- Delayed resuming of runtime-suspended devices during system suspend for
the PCI bus type and ACPI PM domain.
- New set of PM helper routines to allow device runtime PM callbacks to
be used during system suspend and resume more easily from Ulf Hansson.
- Assorted fixes and cleanups in the PM core from Geert Uytterhoeven,
Prabhakar Lad, Philipp Zabel, Rashika Kheria, Sebastian Capella.
- devfreq fix from Saravana Kannan.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=ywR6
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"The majority of this material spent some time in linux-next, some of
it even several weeks. There are a few relatively fresh commits in
it, but they are mostly fixes and simple cleanups.
ACPI took the lead this time, both in terms of the number of commits
and the number of modified lines of code, cpufreq follows and there
are a few changes in the PM core and in cpuidle too.
A new feature that already got some LWN.net's attention is the device
PM QoS extension allowing latency tolerance requirements to be
propagated from leaf devices to their ancestors with hardware
interfaces for specifying latency tolerance. That should help systems
with hardware-driven power management to avoid going too far with it
in cases when there are latency tolerance constraints.
There also are some significant changes in the ACPI core related to
the way in which hotplug notifications are handled. They affect PCI
hotplug (ACPIPHP) and the ACPI dock station code too. The bottom line
is that all those notification now go through the root notify handler
and are propagated to the interested subsystems by means of callbacks
instead of having to install a notify handler for each device object
that we can potentially get hotplug notifications for.
In addition to that ACPICA will now advertise "Windows 2013"
compatibility for _OSI, because some systems out there don't work
correctly if that is not done (some of them don't even boot).
On the system suspend side of things, all of the device suspend and
resume callbacks, except for ->prepare() and ->complete(), are now
going to be executed asynchronously as that turns out to speed up
system suspend and resume on some platforms quite significantly and we
have a few more optimizations in that area.
Apart from that, there are some new device IDs and fixes and cleanups
all over. In particular, the system suspend and resume handling by
cpufreq should be improved and the cpuidle menu governor should be a
bit more robust now.
Specifics:
- Device PM QoS support for latency tolerance constraints on systems
with hardware interfaces allowing such constraints to be specified.
That is necessary to prevent hardware-driven power management from
becoming overly aggressive on some systems and to prevent power
management features leading to excessive latencies from being used
in some cases.
- Consolidation of the handling of ACPI hotplug notifications for
device objects. This causes all device hotplug notifications to go
through the root notify handler (that was executed for all of them
anyway before) that propagates them to individual subsystems, if
necessary, by executing callbacks provided by those subsystems
(those callbacks are associated with struct acpi_device objects
during device enumeration). As a result, the code in question
becomes both smaller in size and more straightforward and all of
those changes should not affect users.
- ACPICA update, including fixes related to the handling of _PRT in
cases when it is broken and the addition of "Windows 2013" to the
list of supported "features" for _OSI (which is necessary to
support systems that work incorrectly or don't even boot without
it). Changes from Bob Moore and Lv Zheng.
- Consolidation of ACPI _OST handling from Jiang Liu.
- ACPI battery and AC fixes allowing unusual system configurations to
be handled by that code from Alexander Mezin.
- New device IDs for the ACPI LPSS driver from Chiau Ee Chew.
- ACPI fan and thermal optimizations related to system suspend and
resume from Aaron Lu.
- Cleanups related to ACPI video from Jean Delvare.
- Assorted ACPI fixes and cleanups from Al Stone, Hanjun Guo, Lan
Tianyu, Paul Bolle, Tomasz Nowicki.
- Intel RAPL (Running Average Power Limits) driver cleanups from
Jacob Pan.
- intel_pstate fixes and cleanups from Dirk Brandewie.
- cpufreq fixes related to system suspend/resume handling from Viresh
Kumar.
- cpufreq core fixes and cleanups from Viresh Kumar, Stratos
Karafotis, Saravana Kannan, Rashika Kheria, Joe Perches.
- cpufreq drivers updates from Viresh Kumar, Zhuoyu Zhang, Rob
Herring.
- cpuidle fixes related to the menu governor from Tuukka Tikkanen.
- cpuidle fix related to coupled CPUs handling from Paul Burton.
- Asynchronous execution of all device suspend and resume callbacks,
except for ->prepare and ->complete, during system suspend and
resume from Chuansheng Liu.
- Delayed resuming of runtime-suspended devices during system suspend
for the PCI bus type and ACPI PM domain.
- New set of PM helper routines to allow device runtime PM callbacks
to be used during system suspend and resume more easily from Ulf
Hansson.
- Assorted fixes and cleanups in the PM core from Geert Uytterhoeven,
Prabhakar Lad, Philipp Zabel, Rashika Kheria, Sebastian Capella.
- devfreq fix from Saravana Kannan"
* tag 'pm+acpi-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (162 commits)
PM / devfreq: Rewrite devfreq_update_status() to fix multiple bugs
PM / sleep: Correct whitespace errors in <linux/pm.h>
intel_pstate: Set core to min P state during core offline
cpufreq: Add stop CPU callback to cpufreq_driver interface
cpufreq: Remove unnecessary braces
cpufreq: Fix checkpatch errors and warnings
cpufreq: powerpc: add cpufreq transition latency for FSL e500mc SoCs
MAINTAINERS: Reorder maintainer addresses for PM and ACPI
PM / Runtime: Update runtime_idle() documentation for return value meaning
video / output: Drop display output class support
fujitsu-laptop: Drop unneeded include
acer-wmi: Stop selecting VIDEO_OUTPUT_CONTROL
ACPI / gpu / drm: Stop selecting VIDEO_OUTPUT_CONTROL
ACPI / video: fix ACPI_VIDEO dependencies
cpufreq: remove unused notifier: CPUFREQ_{SUSPENDCHANGE|RESUMECHANGE}
cpufreq: Do not allow ->setpolicy drivers to provide ->target
cpufreq: arm_big_little: set 'physical_cluster' for each CPU
cpufreq: arm_big_little: make vexpress driver depend on bL core driver
ACPI / button: Add ACPI Button event via netlink routine
ACPI: Remove duplicate definitions of PREFIX
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTOOOnAAoJEHm+PkMAQRiGsBAH/2PAOL3TbOG6tEedxQrTwsr2
muRIRTVWawjT8/npbHupxGnAyAVdmdffBHpmCmcftKdKNryT3YZW8/JWoYc+WSlo
3vTDJHDOYAe6yCBjjhYwcu150THBQdOymOi5mbbclo0XWYG18jd3+abYprRH6SiD
XqNSzYqoiv91JHBAWKBIpo1cyRDuwoM7+jZ7gX41r2800EL7loY3e08cPDDNU6HA
CKaLXMwLwYTefE+Wnr+4UUr08NbNBbBUKLUSXVqKKIpd+MtbyhV1SnWzz8VQSkag
K/uzsnGnE7nrqoepMSx3nXxzOWxUSY2EMbwhEjaKK4xBq9C9pzv3sG/o2/IyopU=
=Nuom
-----END PGP SIGNATURE-----
Merge tag 'v3.14' into drm-intel-next-queued
Linux 3.14
The vt-d w/a merged late in 3.14-rc needs a bit of fine-tuning, hence
backmerge.
Conflicts:
drivers/gpu/drm/i915/i915_gem_gtt.c
drivers/gpu/drm/i915/intel_ddi.c
drivers/gpu/drm/i915/intel_dp.c
All trivial adjacent lines changed type conflicts, so trivial git
doesn't even show them in the merg commit.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we were on a non-optimus device, we'd return -EINVAL, this would
lead to the over engineered runtime pm system to go into an error
state, subsequent get_sync's would fail, so we'd never be able
to open the device again.
(like really get_sync shouldn't fail if the device isn't powered
down).
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Add a missing newline at the end of a DRM_INFO message.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Other kind of accesses are unreliable on Kepler cards. As advised by NVIDIA,
let's only use 32-bit accesses to fetch the vbios from PROM.
This fixes vbios fetching on my nve7 which failed in certain specific
conditions.
I suggest we Cc stable, for all kernels they still maintain after the big
rewrite.
Suggested-by: Christian Zander <czander@nvidia.com>
Signed-off-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This should fix automatic fan management on fermi cards who do not have
0x46 entries in the thermal table.
On my nve6, the blob sets the default linear range from 40°C to 100°C
but my nvcf's default values are 40°C to 85°C. Let's keep 85 as a default
for everyone.
Signed-off-by: Martin Peres <martin.peres@labri.fr>
Tested-by: Timothée Ravier <tim@siosm.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This should fix fan management on many nvd7+ chipsets.
Signed-off-by: Martin Peres <martin.peres@labri.fr>
Tested-by: Timothée Ravier <tim@siosm.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This should fix a deadlock that has been reported to us where fan_update()
would hold the fan lock and try to grab the alarm_program_lock to reschedule
an update. On an other CPU, the alarm_program_lock would have been taken
before calling fan_update(), leading to a deadlock.
We should Cc: <stable@vger.kernel.org> # 3.9+
Reported-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Tested-by: Timothée Ravier <tim@siosm.fr>
Tested-by: Boris Fersing (IRC nick fersingb, no public email address)
Signed-off-by: Martin Peres <martin.peres@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
*hpos horizontal scanout position doesn't need to be corrected
to count the pixels between hactive end and htotal negative.
That is only needed for *vpos to count lines until end of
vblank for the vblank timestamping.
Use hpos as is without correction.
Removes occassional spikes in timestamps of up to 1 scanline
duration, thereby improves accuracy to about +/- 2 usecs instead
of +/- 12 usecs, wrt. true onset time as measured with high
precision equipment on NV-A5.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Alexandre Courbot