Currently ar->flag maintains interface stats. Move interface
specific states from ar->flag to vif->flags.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
vif specific information need to be moved from struct ath6kl.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is not necessary to use ath6kl_get_fw_iftype() to find out the
firmware interface type during initialization because the type
of the initial interface in INFRA_NETWORK. Hardcode the fw interface
type corresponding to INFRA_BSS instead of using ath6kl_get_fw_iftype().
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This refactoring is done in a manner that it can be used
for multiple virtual interface.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is to avoid using ar->wdev to get wiphy pointer, this
may need further cleanup for multi vif support.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ar is again taken from private area of net_device in ath6kl_init(), pass
ar directly.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In order to allow user space based control of background scan interval,
we use available debugfs infrastructure. The feature has been added for
testing purposes. The user has to write the bgscan interval (in secs) to
the bgscan_interval file in ath6kl debug directory. To disable bgscan,
a '0' is to be written to the bgscan_interval file.
Example:
echo "2" > bgscan_interval
This will make the background scan interval as 2 seconds
kvalo: changed implementation so that there's only one call to
ath6kl_wmi_scanparams_cmd()
Signed-off-by: Rishi Panjwani <rpanjwan@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
That way we htc level debug messages can be removed from hif files. Also
add few new messages and remove useless debug message about using
synchrous irq processing (we don't support anything else).
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's currently possible to dump full sdio packets, so dumping htc packets
is not strictly needed. So remove it, we can always add it back if
there ever comes a need for that.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In order to allow user space based QOS control we use the available debugfs
infrastructure. With this feature, user can make changes to qos parameters,
thereby allowing creation and deletion of user defined priority streams and
features like uapsd. This feature has been added for testing purposes.
All 21 parameters for the create_qos command are mandatory in the correct
order. They have to be written to the create_qos file in
the ath6kl debug directory. These parameters(in order) are:
1)user priority
2)direction
3)traffic class
4)traffic type
5)voice PS capability
6)min service intvl
7)max service intvl
8)inactivity intvl
9)suspension intvl
10)serv start time
11)tsid
12)nominal msdu
13)max msdu
14)min data rate
15)mean data rate
16)peak data rate
17)max burst size
18)delay bound
19)min phy rate
20)surplus bw allowance
21)medium time
To create a qos stream:
echo "6 2 3 1 1 9999999 9999999 9999999 7777777 0 6 45000 200 56789000
56789000 5678900 0 0 9999999 20000 0" > create_qos
delete_qos requires 2 parameters:
1)traffic class
2)tsid
To delete a qos stream:
echo "3 1" > delete_qos
kvalo: minor commit log cleanup
Signed-off-by: Rishi Panjwani <rpanjwan@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The previous version did not really make much sense and the theoretical
maximum length would be a bit longer. Calculate the length more
accurately. In addition, there is no need to clear the buffer, so use
kmalloc instead of kzalloc. For bonus points, add the forgotten
cred_rpt_from_other value to the file.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add missing {}'s that caused ath6kl_sdio_suspend to always return -EINVAL
causing suspend to be aborted.
kvalo: I broke this in commit f7325b85e ("ath6kl: add sdio debug messages")
Signed-off-by: Sam Leffler <sleffler@chromium.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sangwook found out that commit 639d0b89 ("ath6kl: read firmware start
address from hardware") broke firmware boot on ar6003 hw2.0 as it seems
it's not posible to automatically query the address from hardware. So
we need to hardcode the address for hw2.0.
Reported-by: Sangwook Lee <sangwook.lee@linaro.org>
Tested-by: Sangwook Lee <sangwook.lee@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use vendor-specific suite selectors to allow CCKM to be configured.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The new debugfs files keepalive and disconnect_timeout can be used to
fetch the current values and to change the values for keepalive and
disconnect event timeout (both in seconds).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Roaming mode can be changed by writing roam mode (default, bssbias, or
lock) to roam_mode. Forced roam can be requested by writing the BSSID
into force_roam.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The new roam_table debugfs file can be used to display the current
roam table from the target.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This file can be used to fetch endpoint statistics counters and
to clear them by writing 0 to it.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For some WPS test items, such as item "5.1.14"
STAUT must include the WSC IE in the 802.11 Association Request frame.
Therefore, add the corresponding IE in association message.
Signed-off-by: Kevin Fang <kevin.fang@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
smatch found that skb might be null in some cases in ath6kl_rx():
ath6kl/txrx.c +1252 ath6kl_rx(222) error: potential null derefence 'skb'.
This will happen when ath6kl is in AP mode and two clients send traffic
to each other.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There's no use for these, at least right now, so better to remove them.
If some of them are ever needed, we can always add them back.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Power save is enabled during ath6kl init. But when user space disables power
save, the system will go into suspend with power save disabled. The ath6kl
driver will now explicitly enable power save prior to entering suspend and
restore its previous setting upon resume
Signed-off-by: Chilam Ng <chilamng@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is just a four byte information of the received message
from ath6kl_htc_rxmsg_pending_handler(). Remove unnecessary
array representaion.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is not necessary to process an htc_packet which is allocated for rx
but failed in sdio rx. Though it does not fix any real issue, it does
not make much sense to process the failed frame.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is found during the code review. As the leak would happen only
in failure case, the imapct is not easily visible.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Packet is not reclaimed when ath6kl_htc_rx_process_hdr() fails.
Fix this by deferring the packet deletion from comp_pktq till
ath6kl_htc_rx_process_hdr() returns success. This bug is found
in code review, impact is not easily visible as the leak happens
only in failure cases.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are places where tx_complete callbacks are called with
claiming the sdio function. It is not necessary to hold the
sdio func for longer. This may even affect the host side power
save, if it is supported by the controller.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is not necessary to use spinlock primitive to
protect data which is accessed in hard irq context as
nothing is running in hard irq with this driver. The
spinlock primitive meant to protect data in softirq
context is more appropriate.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This was disabled beacause there was a network stall
issue when scan is issued. This issue does not happen
with the new firmware (3.1.1.609), enable it back.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Probably we never hit this condition, but in case we do, we may as
well put a return here instead of just printing a warning message and
then corrupting memory. The caller doesn't check the return code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By default SDIO multiport aggregation is disabled. It's useful to
get good throughput results. This patch enables it.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We dereference adapter in the error handling code so this needed to
be fixed. This function is always called like:
adapter->if_ops.host_to_card(adapter, ...);
so adapter can never be NULL and I've removed the NULL check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The previous if statement means this that pointer is NULL so there
is no need to free it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use kstrtoul, etc instead of the now deprecated strict_strtoul, etc.
A semantic patch rule for the kstrtoul case is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression a,b;
{int,long} *c;
@@
-strict_strtoul
+kstrtoul
(a,b,c)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use kstrtoul, etc instead of the now deprecated strict_strtoul, etc.
A semantic patch rule for the kstrtoul case is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression a,b;
{int,long} *c;
@@
-strict_strtoul
+kstrtoul
(a,b,c)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement the socket wifi TX status error
queue reflection in mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new wifi socket TX capability should be
supported by wifi drivers, let them advertise
whether they do or not.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prepare for adding backplane interconnect type support
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use SSB macros in order to clean up brcmfmac code
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is part of the abstracting chip backplane handle code
series.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan