The mdp5_cmd_encoder_disable is accidentally called in the encoder enable
path. We've not seen any problems since we haven't tested with command
mode panels in a while. Fix the copy-paste error.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
After the commit mentioned below, we start computing the byte and pixel
clocks (dsi_calc_clk_rate) in the DSI bridge's mode_set() op. The
calculation involves the number of DSI lanes being used by the
downstream bridge/panel.
If the downstream bridge/panel tries to change the number of DSI lanes
(as done in the ADV7533 driver) in its mode_set() op, then our DSI
host driver will not have the correct number of lanes when computing
byte/pixel clocks.
Fix this by delaying the clock rate calculation in the DSI bridge
enable path. In particular, compute the clock rates in
msm_dsi_host_get_phy_clk_req().
This fixes the DSI host error interrupts seen when we try to switch
between modes that require different number of lanes (4 to 3 lanes, or
vice versa) on db410c. The error interrupts occur since the byte/pixel
clock rates aren't according to what the DSI video mode timing engine
expects.
Fixes: b62aa70a98 ("drm/msm/dsi: Move PHY operations out of host")
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We recently added locking to this function but there was a direct return
that was overlooked where we need to unlock.
Fixes: 0e08270a1f ("drm/msm: Separate locking of buffer resources from struct_mutex")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We recently added an integer overflow check but it needs an additional
tweak to work properly on 32 bit systems.
The problem is that we're doing the right hand side of the assignment as
type unsigned long so the max it will have an integer overflow instead
of being larger than SIZE_MAX. That means the "sz > SIZE_MAX" condition
is never true even on 32 bit systems. We need to first cast it to u64
and then do the math.
Fixes: 4a630fadbb ("drm/msm: Fix potential buffer overflow issue")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Following compilation warnings were observed for these files:
CC [M] drivers/gpu/drm/msm/mdp/mdp5/mdp5_mdss.o
drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c: In function 'blend_setup':
drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c:223:7: warning: missing braces around initializer [-Wmissing-braces]
enum mdp5_pipe stage[STAGE_MAX + 1][MAX_PIPE_STAGE] = { SSPP_NONE };
^
drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c:223:7: warning: (near initialization for 'stage[0]') [-Wmissing-braces]
drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c:224:7: warning: missing braces around initializer [-Wmissing-braces]
enum mdp5_pipe r_stage[STAGE_MAX + 1][MAX_PIPE_STAGE] = { SSPP_NONE };
^
drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c:224:7: warning: (near initialization for 'r_stage[0]') [-Wmissing-braces]
drivers/gpu/drm/msm/mdp/mdp5/mdp5_plane.c: In function 'mdp5_plane_mode_set':
drivers/gpu/drm/msm/mdp/mdp5/mdp5_plane.c:892:9: warning: missing braces around initializer [-Wmissing-braces]
struct phase_step step = { 0 };
^
drivers/gpu/drm/msm/mdp/mdp5/mdp5_plane.c:892:9: warning: (near initialization for 'step.x') [-Wmissing-braces]
drivers/gpu/drm/msm/mdp/mdp5/mdp5_plane.c:893:9: warning: missing braces around initializer [-Wmissing-braces]
struct pixel_ext pe = { 0 };
^
drivers/gpu/drm/msm/mdp/mdp5/mdp5_plane.c:893:9: warning: (near initialization for 'pe.left') [-Wmissing-braces]
This happens because in the first case we were initializing a two
dimensional array with {0} and in the second case we were initializing a
struct containing two arrays with {0}.
Fix them by adding another pair of {}.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This is the plumbing for supporting fb modifiers on planes. Modifiers
have already been introduced to some extent, but this series will extend
this to allow querying modifiers per plane. Based on this, the client to
enable optimal modifications for framebuffers.
This patch simply allows the DRM drivers to initialize their list of
supported modifiers upon initializing the plane.
v2: A minor addition from Daniel
v3:
* Updated commit message
* s/INVALID/DRM_FORMAT_MOD_INVALID (Liviu)
* Remove some excess newlines (Liviu)
* Update comment for > 64 modifiers (Liviu)
v4: Minor comment adjustments (Liviu)
v5: Some new platforms added due to rebase
v6: Add some missed plane inits (or maybe they're new - who knows at
this point) (Daniel)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Daniel Stone <daniels@collabora.com> (v2)
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Daniel Stone <daniels@collabora.com>
for_each_obj_in_state is about to be removed, so convert
to the new iterator macros.
Just like in omap, use crtc_state->active instead of
crtc_state->enable when waiting for completion.
Changes since v1:
- Fix compilation.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Rob Herring <robh@kernel.org>
Cc: Markus Elfring <elfring@users.sourceforge.net>
Cc: Sushmita Susheelendra <ssusheel@codeaurora.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20170719143920.25685-6-maarten.lankhorst@linux.intel.com
drm_atomic_helper_swap_state() will be changed to interruptible waiting
in the next few commits, so all drivers have to be changed to handling
failure.
MSM has its own busy tracking, which means the swap_state call can be
done with stall = false, in which case it should never return an error.
Handle failure with BUG_ON for this reason.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Link: http://patchwork.freedesktop.org/patch/msgid/20170711143314.2148-8-maarten.lankhorst@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Tested-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- FBINFO_CAN_FORCE_OUTPUT has been a lie ever since we nerfed&removed
the entire panic handling code in our fbdev emulation. We might
restore kms panic output, but not through the bazillion of legacy
code layers called fbdev/fbcon, there's just no way to make that
work safely.
- With the module check change FBINFO_DEFAULT is always 0, so can be
removed too.
That removes another change to cargo-cult stuff in kms drivers, yay!
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170706125735.28299-5-daniel.vetter@ffwll.ch
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
HDMI 1.4b support the CEA video modes as per range of CEA-861-D (VIC 1-64).
For any other mode, the VIC filed in AVI infoframes should be 0.
HDMI 2.0 sinks, support video modes range as per CEA-861-F spec, which is
extended to (VIC 1-107).
This patch adds a bool input variable, which indicates if the connected
sink is a HDMI 2.0 sink or not. This will make sure that we don't pass a
HDMI 2.0 VIC to a HDMI 1.4 sink.
This patch touches all drm drivers, who are callers of this function
drm_hdmi_avi_infoframe_from_display_mode but to make sure there is
no change in current behavior, is_hdmi2 is kept as false.
In case of I915 driver, this patch:
- checks if the connected display is HDMI 2.0.
- HDMI infoframes carry one of this two type of information:
- VIC for 4K modes for HDMI 1.4 sinks
- S3D information for S3D modes
As CEA-861-F has already defined VICs for 4K videomodes, this
patch doesn't allow sending HDMI infoframes for HDMI 2.0 sinks,
until the mode is 3D.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jose Abreu <jose.abreu@synopsys.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
PS: This patch touches a few lines in few files, which were
already above 80 char, so checkpatch gives 80 char warning again.
- gpu/drm/omapdrm/omap_encoder.c
- gpu/drm/i915/intel_sdvo.c
V2: Rebase, Added r-b from Andrzej
V3: Addressed review comment from Ville:
- Do not send VICs in both AVI-IF and HDMI-IF
send only one of it.
V4: Rebase
V5: Added r-b from Neil.
Addressed review comments from Ville
- Do not block HDMI vendor IF, instead check for VIC while
handling AVI infoframes
V6: Rebase
V7: Rebase
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1499960000-9232-2-git-send-email-shashank.sharma@intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
The CRTC .disable() helper operation is deprecated for atomic drivers,
the new .atomic_disable() helper operation being preferred. Convert all
atomic drivers to .atomic_disable() to avoid cargo-cult use of
.disable() in new drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> # for sun4i
Acked-by: Philipp Zabel <p.zabel@pengutronix.de> # for mediatek
Acked-by: Alexey Brodkin <abrodkin@synopsys.com> # for arcpgu
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> # for atmel-hlcdc
Tested-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Vincent Abriou <vincent.abriou@st.com> # for sti
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> # for vmwgfx
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170630093646.7928-3-laurent.pinchart+renesas@ideasonboard.com
The old state is useful for drivers that need to perform operations at
enable time that depend on the transition between the old and new
states.
While at it, rename the operation to .atomic_enable() to be consistent
with .atomic_disable(), as the .enable() operation is used by atomic
helpers only.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> # for sun4i
Acked-by: Philipp Zabel <p.zabel@pengutronix.de> # for imx-drm and mediatek
Acked-by: Alexey Brodkin <abrodkin@synopsys.com> # for arcpgu
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> # for atmel-hlcdc
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com> # for hdlcd and mali-dp
Acked-by: Stefan Agner <stefan@agner.ch> # for fsl-dcu
Tested-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Vincent Abriou <vincent.abriou@st.com> # for sti
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> # for vmwgfx
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170630093646.7928-2-laurent.pinchart+renesas@ideasonboard.com
In function submit_create, if nr_cmds or nr_bos is assigned with
negative value, the allocated buffer may be small than intended.
Using this buffer will lead to buffer overflow issue.
Signed-off-by: Kasin Li <donglil@codeaurora.org>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Buffer object specific resources like pages, domains, sg list
need not be protected with struct_mutex. They can be protected
with a buffer object level lock. This simplifies locking and
makes it easier to avoid potential recursive locking scenarios
for SVM involving mmap_sem and struct_mutex. This also removes
unnecessary serialization when creating buffer objects, and also
between buffer object creation and GPU command submission.
Signed-off-by: Sushmita Susheelendra <ssusheel@codeaurora.org>
[robclark: squash in handling new locking for shrinker]
Signed-off-by: Rob Clark <robdclark@gmail.com>
A 2 pixel wide pink strip was observed on the left end of some HDMI
monitors configured in a HDMI mode.
It turned out that we were missing out on configuring AVI infoframes, and
unlike APQ8064, the 8x96 HDMI H/W seems to be sensitive to that.
Add configuration of AVI infoframes. While at it, make sure that
hdmi_audio_update is only called when we've detected that the monitor
supports HDMI.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Without doing anything in unprepare, the HDMI driver isn't able to
switch modes successfully. Calling set_rate with a new rate results
in an un-locked PLL.
If we reset the PLL in unprepare, the PLL is able to lock with the
new rate.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Commit c0c0d9eeeb ("drm/msm: hdmi audio support") uses logical
OR operators to build up a value to be written in the
REG_HDMI_AUDIO_INFO0 and REG_HDMI_AUDIO_INFO1 registers when it
should have used bitwise operators.
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Fixes: c0c0d9eeeb ("drm/msm: hdmi audio support")
Signed-off-by: Rob Clark <robdclark@gmail.com>
Now that the msm_gem supports an arbitrary number of vma's, we no longer
need to assign an id (index) to each address space. So rip out the
associated code.
Signed-off-by: Rob Clark <robdclark@gmail.com>
It means we have to do a list traversal where we once had an index into
a table. But the list will normally have one or two entries.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Pull some of the logic out into msm_gem_new() (since we don't need to
care about the imported-bo case), and don't defer allocating pages. The
latter is generally a good idea, since if we are using VRAM carveout to
allocate contiguous buffers (ie. no IOMMU), the allocation is more
likely to fail. So failing at allocation time is a more sane option.
Plus this simplifies things in the next patch.
Signed-off-by: Rob Clark <robdclark@gmail.com>
No functional change, that will come later. But this will make it
easier to deal with dynamically created address spaces (ie. per-
process pagetables for gpu).
Signed-off-by: Rob Clark <robdclark@gmail.com>
Before we can shift to passing the address-space object to _get_iova(),
we need to fix a few places (dsi+fbdev) that were hard-coding the adress
space id. That gets somewhat easier if we just move these to the kms
base class.
Prep work for next patch.
Signed-off-by: Rob Clark <robdclark@gmail.com>
It serves no purpose, things should be sufficiently synchronized already
by atomic framework. And it is somewhat awkward to be holding a spinlock
when msm_gem_iova() is going to start needing to grab a mutex.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Most, but not all, paths where calling the with struct_mutex held. The
fast-path in msm_gem_get_iova() (plus some sub-code-paths that only run
the first time) was masking this issue.
So lets just always hold struct_mutex for hw_init(). And sprinkle some
WARN_ON()'s and might_lock() to avoid this sort of problem in the
future.
Signed-off-by: Rob Clark <robdclark@gmail.com>
memptrs->wptr seems to be unused. Remove it to avoid
confusing the upcoming preemption code.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The amount of information that we need to pass into msm_gpu_init()
is steadily increasing, so add a new struct to stabilize the function
call and make it easier to add new configuration down the line.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Modify the 'pad' member of struct drm_msm_gem_info to 'flags'. If the
user sets 'flags' to non-zero it means that they want a IOVA for the
GEM object instead of a mmap() offset. Return the iova in the 'offset'
member.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
[robclark: s/hint/flags in commit msg]
Signed-off-by: Rob Clark <robdclark@gmail.com>
There isn't any generic code that uses ->idle so remove it.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The ioctl array is sparsely populated but the compiler will make sure
that it is sufficiently sized for all the values that we have so we
can safely use ARRAY_SIZE() instead of having a constantly changing
#define in the uapi header.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The A5XX GPU powers on in "secure" mode. In secure mode the GPU can
only render to buffers that are marked as secure and inaccessible
to the kernel and user through a series of hardware protections. In
practice secure mode is used to draw things like a UI on a secure
video frame.
In order to switch out of secure mode the GPU executes a special
shader that clears out the GMEM and other sensitve registers and
then writes a register. Because the kernel can't be trusted the
shader binary is signed and verified and programmed by the
secure world. To do this we need to read the MDT header and the
segments from the firmware location and put them in memory and
present them for approval.
For targets without secure support there is an out: if the
secure world doesn't support secure then there are no hardware
protections and we can freely write the SECVID_TRUST register from
the CPU. We don't have 100% confidence that we can query the
secure capabilities at run time but we have enough calls that
need to go right to give us some confidence that we're at least doing
something useful.
Of course if we guess wrong you trigger a permissions violation
which usually ends up in a system crash but thats a problem
that shows up immediately.
[v2: use child device per Bjorn]
[v3: use generic MDT loader per Bjorn]
[v4: use managed dma functions and ifdefs for the MDT loader]
[v5: Add depends for QCOM_MDT_LOADER]
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[robclark: fix Kconfig to use select instead of depends + #if IS_ENABLED()]
Signed-off-by: Rob Clark <robdclark@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZPdbLAAoJEHm+PkMAQRiGx4wH/1nCjfnl6fE8oJ24/1gEAOUh
biFdqJkYZmlLYHVtYfLm4Ueg4adJdg0wx6qM/4RaAzmQVvLfDV34bc1qBf1+P95G
kVF+osWyXrZo5cTwkwapHW/KNu4VJwAx2D1wrlxKDVG5AOrULH1pYOYGOpApEkZU
4N+q5+M0ce0GJpqtUZX+UnI33ygjdDbBxXoFKsr24B7eA0ouGbAJ7dC88WcaETL+
2/7tT01SvDMo0jBSV0WIqlgXwZ5gp3yPGnklC3F4159Yze6VFrzHMKS/UpPF8o8E
W9EbuzwxsKyXUifX2GY348L1f+47glen/1sedbuKnFhP6E9aqUQQJXvEO7ueQl4=
=m2Gx
-----END PGP SIGNATURE-----
BackMerge tag 'v4.12-rc5' into drm-next
Linux 4.12-rc5 for nouveau fixes
The overrun check for the size of submitted commands is off by one.
It should allow the offset plus the size to be equal to the
size of the memory object when the command stream is very tightly
constructed.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Amongst its other duties, msm_gem_new_impl adds the newly created
GEM object to the shared inactive list which may also be actively
modifiying the list during submission. All the paths to modify
the list are protected by the mutex except for the one through
msm_gem_import which can end up causing list corruption.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
[add extra WARN_ON(!mutex_is_locked(&dev->struct_mutex))]
Signed-off-by: Rob Clark <robdclark@gmail.com>
Use the dma_fence_match_context helper to check if all backing fences
are from our own context, in which case we don't have to wait.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Gustavo Padovan <gustavo.padovan@collabora.com>
[rebased on code-motion]
Signed-off-by: Rob Clark <robdclark@gmail.com>
struct irq_domain_ops is not modified, so it can be made const.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Rob Clark <robdclark@gmail.com>
If we follow the typical pattern of the base class being the first
member, we can use the default dma_fence_free function.
Signed-off-by: Eric Anholt <eric@anholt.net>
Cc: Rob Clark <robdclark@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Without this, polling on the dma-buf (and presumably other devices
synchronizing against our rendering) would return immediately, even
while the BO was busy.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Cc: Rob Clark <robdclark@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Otherwise if someone was using old bindings with "core_clk" instead of
"core" as the clock name, we'd never find it and gpu would be stuck at
27MHz (or whatever it's slowest rate is).
Fixes: 98db803 ("msm/drm: gpu: Dynamically locate the clocks from the device tree")
Signed-off-by: Rob Clark <robdclark@gmail.com>
Otherwise, if nothing else enabled selects it, dev_pm_opp_of_add_table()
will return -ENOTSUPP.
Fixes: e2af8b6 ("drm/msm: gpu: Use OPP tables if we can")
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add DRM_MODE_ROTATE_ and DRM_MODE_REFLECT_ defines to the UAPI
as a convenience.
Ideally the DRM_ROTATE_ and DRM_REFLECT_ property ids are looked up
through the atomic API, but realizing that userspace is likely to take
shortcuts and assume that the enum values are what is sent over the
wire.
As a result these defines are provided purely as a convenience to
userspace applications.
Changes since v3:
- Switched away from past tense in comments
- Add define name change to previously mis-spelled DRM_REFLECT_X comment
- Improved the comment for the DRM_MODE_REFLECT_<axis> comment
Changes since v2:
- Changed define prefix from DRM_MODE_PROP_ to DRM_MODE_
- Fix compilation errors
- Changed comment formatting
- Deduplicated comment lines
- Clarified DRM_MODE_PROP_REFLECT_ comment
Changes since v1:
- Moved defines from drm.h to drm_mode.h
- Changed define prefix from DRM_ to DRM_MODE_PROP_
- Updated uses of the defines to the new prefix
- Removed include from drm_rect.c
- Stopped using the BIT() macro
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170519205017.23307-2-robert.foss@collabora.com
Now that drm_[cm]alloc* helpers are simple one line wrappers around
kvmalloc_array and drm_free_large is just kvfree alias we can drop
them and replace by their native forms.
This shouldn't introduce any functional change.
Changes since v1
- fix typo in drivers/gpu//drm/etnaviv/etnaviv_gem.c - noticed by 0day
build robot
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Michal Hocko <mhocko@suse.com>drm: drop drm_[cm]alloc* helpers
[danvet: Fixup vgem which grew another user very recently.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Christian König <christian.koenig@amd.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170517122312.GK18247@dhcp22.suse.cz
Include <drm/*.h> instead of relative path from include/drm, then
remove the -Iinclude/drm compiler flag.
While we are here, sort the touched parts with public headers first.
mdp4_kms.h must declare struct device_node to be self-contained.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1493009447-31524-11-git-send-email-yamada.masahiro@socionext.com
If we restrict this helper to only kms drivers (which is the case) we
can look up the correct mode easily ourselves. But it's a bit tricky:
- All legacy drivers look at crtc->hwmode. But that is updated already
at the beginning of the modeset helper, which means when we disable
a pipe. Hence the final timestamps might be a bit off. But since
this is an existing bug I'm not going to change it, but just try to
be bug-for-bug compatible with the current code. This only applies
to radeon&amdgpu.
- i915 tries to get it perfect by updating crtc->hwmode when the pipe
is off (i.e. vblank->enabled = false).
- All other atomic drivers look at crtc->state->adjusted_mode. Those
that look at state->requested_mode simply don't adjust their mode,
so it's the same. That has two problems: Accessing crtc->state from
interrupt handling code is unsafe, and it's updated before we shut
down the pipe. For nonblocking modesets it's even worse.
For atomic drivers try to implement what i915 does. To do that we add
a new hwmode field to the vblank structure, and update it from
drm_calc_timestamping_constants(). For atomic drivers that's called
from the right spot by the helper library already, so all fine. But
for safety let's enforce that.
For legacy driver this function is only called at the end (oh the
fun), which is broken, so again let's not bother and just stay
bug-for-bug compatible.
The benefit is that we can use drm_calc_vbltimestamp_from_scanoutpos
directly to implement ->get_vblank_timestamp in every driver, deleting
a lot of code.
v2: Completely new approach, trying to mimick the i915 solution.
v3: Fixup kerneldoc.
v4: Drop the WARN_ON to check that the vblank is off, atomic helpers
currently unconditionally call this. Recomputing the same stuff should
be harmless.
v5: Fix typos and move misplaced hunks to the right patches (Neil).
v6: Undo hunk movement (kbuild).
Cc: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Cc: Eric Anholt <eric@anholt.net>
Cc: Rob Clark <robdclark@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170509140329.24114-4-daniel.vetter@ffwll.ch
It's overkill to have a flag parameter which is essentially used just
as a boolean. This takes care of core + adjusting drivers.
Adjusting the scanout position callback is a bit harder, since radeon
also supplies it's own driver-private flags in there.
v2: Fixup misplaced hunks (Neil).
v3: kbuild says v1 was better ...
Cc: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Cc: Eric Anholt <eric@anholt.net>
Cc: Rob Clark <robdclark@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170509140329.24114-2-daniel.vetter@ffwll.ch
There's really no reason for anything more:
- Calling this while the crtc vblank stuff isn't set up is a driver
bug. Those places alrready DRM_ERROR.
- Calling this when the crtc is off is either a driver bug (calling
drm_crtc_handle_vblank at the wrong time) or a core bug (for
anything else). Again, we DRM_ERROR.
- EINVAL is checked at higher levels already, and if we'd use struct
drm_crtc * instead of (dev, pipe) it would be real obvious that
those are again core bugs.
The only valid failure mode is crap hardware that couldn't sample a
useful timestamp, to ask the core to just grab a not-so-accurate
timestamp. Bool is perfectly fine for that.
v2: Also fix up the one caller, I lost that in the shuffling (Jani).
v3: Fixup commit message (Neil).
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Cc: Eric Anholt <eric@anholt.net>
Cc: Rob Clark <robdclark@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170509140329.24114-1-daniel.vetter@ffwll.ch
Noteworthy changes this time:
1) 4k support for newer chips (ganging up hwpipes and mixers)
2) using OPP bindings for gpu
3) more prep work towards per-process pagetables
* 'msm-next' of git://people.freedesktop.org/~robclark/linux: (47 commits)
msm/drm: gpu: Dynamically locate the clocks from the device tree
drm/msm: gpu: Use OPP tables if we can
drm/msm: Hard code the GPU "slow frequency"
drm/msm: Add MSM_PARAM_GMEM_BASE
drm/msm: Reference count address spaces
drm/msm: Make sure to detach the MMU during GPU cleanup
drm/msm/mdp5: Enable 3D mux in mdp5_ctl
drm/msm/mdp5: Reset CTL blend registers before configuring them
drm/msm/mdp5: Assign 'right' mixer to CRTC state
drm/msm/mdp5: Stage border out on base stage if CRTC has 2 LMs
drm/msm/mdp5: Stage right side hwpipes on Right-side Layer Mixer
drm/msm/mdp5: Prepare Layer Mixers for source split
drm/msm/mdp5: Configure 'right' hwpipe
drm/msm/mdp5: Assign a 'right hwpipe' to plane state
drm/msm/mdp5: Create mdp5_hwpipe_mode_set
drm/msm/mdp5: Add optional 'right' Layer Mixer in CRTC state
drm/msm/mdp5: Add a CAP for Source Split
drm/msm/mdp5: Remove mixer/intf pointers from mdp5_ctl
drm/msm/mdp5: Start using parameters from CRTC state
drm/msm/mdp5: Add more stuff to CRTC state
...
Last drm-misc-next pull req for 4.12
Core changes:
- fb_helper checkpatch cleanup and simplified _add_one_connector() (Thierry)
- drm_ioctl and drm_sysfs improved/gained documentation (Daniel)
- [ABI] Repurpose reserved field in drm_event_vblank for crtc_id (Ander)
- Plumb acquire ctx through legacy paths to avoid lock_all and legacy_backoff
(Daniel)
- Add connector_atomic_check to check conn constraints on modeset (Maarten)
- Add drm_of_find_panel_or_bridge to remove boilerplate in drivers (Rob)
Driver changes:
- meson moved to drm-misc (Neil)
- Added support for Amlogic GX SoCs in dw-hdmi (Neil)
- Rockchip unbind actually cleans up the things bind initializes (Jeffy)
- A couple misc fixes in virtio, dw-hdmi
NOTE: this also includes a backmerge of drm-next as well rc5 (we needed vmwgfx
as well as the new synopsys media formats)
* tag 'drm-misc-next-2017-04-07' of git://anongit.freedesktop.org/git/drm-misc: (77 commits)
Revert "drm: Don't allow interruptions when opening debugfs/crc"
drm: Only take cursor locks when the cursor plane exists
drm/vmwgfx: Fix fbdev emulation using legacy functions
drm/rockchip: Shutdown all crtcs when unbinding drm
drm/rockchip: Reorder drm bind/unbind sequence
drm/rockchip: analogix_dp: Disable clock when unbinding
drm/rockchip: vop: Unprepare clocks when unbinding
drm/rockchip: vop: Enable pm domain before vop_initial
drm/rockchip: cdn-dp: Don't unregister audio dev when unbinding
drm/rockchip: cdn-dp: Don't try to release firmware when not loaded
drm: bridge: analogix: Destroy connector & encoder when unbinding
drm: bridge: analogix: Disable clock when unbinding
drm: bridge: analogix: Unregister dp aux when unbinding
drm: bridge: analogix: Detach panel when unbinding analogix dp
drm: Don't allow interruptions when opening debugfs/crc
drm/virtio: don't leak bo on drm_gem_object_init failure
drm: bridge: dw-hdmi: fix input format/encoding from plat_data
drm: omap: use common OF graph helpers
drm: convert drivers to use drm_of_find_panel_or_bridge
drm: convert drivers to use of_graph_get_remote_node
...
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJY6mY1AAoJEHm+PkMAQRiGB14IAImsH28JPjxJVDasMIRPBxVc
euPPlZgoBieu7sNt+kEsEqdkXuu0MLk6gln0IGxWLeoB2S+u3Tz5LMa2YArVqV9Z
tWzOnI9auE73P2Pz/tUMOdyMs5tO0PolQxX3uljbULBozOHjHRh13fsXchX2yQvl
mFeFCDqpPV0KhWRH/ciA8uIHdvYPhMpkKgRtmR8jXL0yzqLp6+2J+Bs8nHG4NNng
HMVxZPC8jOE/TgWq6k/GmXgxh3H/AideFdHFbLKYnIFJW41ZGOI8a262zq3NmjPd
lywpVU7O7RMhSITY5PnuR3LpNV8ftw1hz2y6t35unyFK1P02adOSj5GJ3hGdhaQ=
=Xz5O
-----END PGP SIGNATURE-----
Backmerge tag 'v4.11-rc6' into drm-next
Linux 4.11-rc6
drm-misc needs 4.11-rc5, may as well fix conflicts with rc6.
Instead of using a fixed list of clock names use the clock-names
list in the device tree to discover and get the list of clocks
that we need.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
If a OPP table is defined for the GPU device in the device tree use
that in lieu of the downstream style GPU frequency table. If we do
use the downstream table convert it to a OPP table so that we can
take advantage of the OPP lookup facilities later.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Some A3XX and A4XX GPU targets required that the GPU clock be
programmed to a non zero value when it was disabled so
27Mhz was chosen as the "invalid" frequency.
Even though newer targets do not have the same clock restrictions
we still write 27Mhz on clock disable and expect the clock subsystem
to round down to zero.
For unknown reasons even though the slow clock speed is always
27Mhz and it isn't actually a functional level the legacy device tree
frequency tables always defined it and then did gymnastics to work
around it.
Instead of playing the same silly games just hard code the "slow" clock
speed in the code as 27MHz and save ourselves a bit of infrastructure.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
User space needs to know where the GMEM whole starts so that they
can set up the addressing correctly.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
There are reasons for a memory object to outlive the file descriptor
that created it and so the address space that a buffer object is
attached to must also outlive the file descriptor. Reference count
the address space so that it can remain viable until all the objects
have released their addresses.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We should be detaching the MMU before destroying the address
space. To do this cleanly, the detach has to happen in
adreno_gpu_cleanup() because it needs access to structs
in adreno_gpu.c. Plus it is better symmetry to have
the attach and detach at the same code level.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
3D mux is a small block placed after the DSPPs in MDP5. It can merge
2 LM/DSPP outputs and feed it to a single interface.
Enable 3D Mux if our mdp5_pipeline has 2 active LMs. This check
will need to be made more specific later when we add Dual DSI
support with source split enabled. In that use case, each LM feeds to a
separae INTF, so the 3D mux isn't needed.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Assigning LMs dynamically to CRTCs results in REG_MDP5_CTL_LAYER_REGs
and REG_MDP5_CTL_LAYER_EXT_REGs maintaining old values for a LM that
isn't used by our CTL instance anymore.
Clear the ctl's CTL_LAYER_REG and CTL_LAYER_EXT_REGs for all LM
instances. The ones that need to be configured are configured later
in this func.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Dynamically assign a right mixer to mdp5_crtc_state in the CRTC's
atomic_check path. Assigning the right mixer has some constraints,
i.e, only a few LMs can be paired together. Update mdp5_mixer_assign
to handle these constraints.
Firstly, we need to identify whether we need a right mixer or not.
At the moment, there are 2 scenarios where a right mixer might be
needed:
- If any of the planes connected to this CRTC is too wide (i.e, is
comprised of 2 hwpipes).
- If the CRTC's mode itself is too wide (i.e, a 4K mode on HDMI).
We implement both these checks in the mdp5_crtc_atomic_check(), and
pass 'need_right_mixer' to mdp5_setup_pipeline.
If a CRTC is already assigned a single mixer, and a new atomic commit
brings in a drm_plane that needs 2 hwpipes, we can successfully commit
this mode without requiring a full modeset, provided that we still use
the previously assigned mixer as the left mixer. If such an assignment
isn't possible, we'd need to do a full modeset. This scenario has been
ignored for now.
The mixer assignment code is a bit messy, considering we have at most
4 LM instances in hardware. This can probably be re-visited later with
simplified logic.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
If a CRTC comprises of 2 LMs, it is mandatory to enable border out
and assign it to the base stage.
We had to enable border out also when the base plane wasn't fullscreen.
Club these checks and put them in a separate function called
get_start_stage() that returns the starting stage for assigning planes.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Now that our mdp5_planes can consist of 2 hwpipes, update the
blend_setup() code to stage the right hwpipe to the left and
right LMs
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In order to enable Source Split in HW, we need to add/modify
a few LM register configurations:
- Configure the LM width to be half the mode width, so that
each LM manages one half of the scanout.
- Tell the 'right' LM that it is configured to be the 'right'
LM in source split mode.
- Since we now have 2 places where REG_MDP5_LM_BLEND_COLOR_OUT is
configured, do a read-update-store for the register instead of
directly writing a value to it.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Now that we have a right hwpipe in mdp5_plane_state, configure it
mdp5_plane_mode_set(). The only parameters that vary between the
left and right hwpipes are the src_w, src_img_w, src_x and crtc_x
as we just even chop the fb into left and right halves.
Add a mdp5_plane_right_pipe() which will be used by the crtc code
to set up LM stages.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
If the drm_plane has a source width that's greater than the max width
supported by a SSPP (2560 pixels on 8x96), then we assign a 'r_hwpipe'
to it in mdp5_plane_atomic_check().
TODO: There are a few scenarios where the hwpipe assignments aren't
recommended by HW. For example, an assignment which results in a
drm_plane to of two different types of hwpipes (say RGB0 on left
and DMA1 on right) is not recommended.
Also, hwpipes have a priority mapping, where the higher priority pipe
needs to be staged on left LM, and the lower priority needs to be
staged on the right LM. For example, the priority order for VIG pipes
in decreasing order of priority is VIG0, VIG1, VIG2, and VIG3. So, VIG0
on left and VIG1 on right is a correct configuration, but VIG1 on left
and VIG0 on right isn't. These scenarios are ignored for now for the
sake of simplicity.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Refactor mdp5_plane_mode_set to call mdp5_hwpipe_mode_set. The latter
func takes in only the hwpipe and the parameters that need to be
programmed into the hwpipe registers. All the code that calculates these
parameters is left as is in mdp5_plane_mode_set.
In the future, when we let drm_plane be comprised of 2 hwpipes, this func
allow us to configure each pipe without adding redundant code.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add another mdp5_hw_mixer pointer (r_mixer) in mdp5_crtc_state.
This mixer will be used to generate the right half of the scanout.
With Source Split, a SSPP can now be connected to 2 Layer Mixers, but
has to be at the same blend level (stage #) on both Layer Mixers.
A drm_plane that has a lesser width than the max width supported, will
comprise of a single SSPP/hwpipe, staged on both the Layer Mixers at
the same blend level. A plane that is greater than max width will comprise
of 2 SSPPs, with the 'left' SSPP staged on the left LM, and the 'right'
SSPP staged on the right LM at the same blend level.
For now, the drm_plane consists of only one SSPP, therefore, it
needs to be staged on both the LMs in blend_setup() and mdp5_ctl_blend().
We'll extend this logic to support 2 hwpipes per plane later.
The crtc cursor ops (using the LM cursors, not SSPP cursors) simply
return an error if they're called when the right mixer is assigned to
the CRTC state. With source split is enabled, we're expected to only
SSPP cursors.
This commit adds code that configures the right mixer, but the r_mixer
itself isn't assigned at the moment.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Some of the newer MDP5 versions support Source Split of SSPPs. It is a
feature that allows us to route the output of a hwpipe to 2 Layer
Mixers. This is required to achieve the following use cases:
- Dual DSI: For high res DSI panels (such as 2560x1600 etc), a single
DSI interface doesn't have the bandwidth to drive the required pixel
clock. We use 2 DSI interfaces to drive the left and right halves
of the panel (i.e, 1280x1600 each). The MDP5 pipeline here would look
like:
LM0 -- DSPP0 -- INTF1 -- DSI1
/
hwpipe--
\
LM1 -- DSPP1 -- INTF2 -- DSI2
A single hwpipe is used to scan out the left and right halves to DSI1
and DSI2 respectively. In order to do this, we need to configure the
2 Layer Mixers in Source Split mode.
- HDMI 4K: In order to support resolutions with width higher than the
max width supported by a hwpipe, we club 2 hwpipes together:
hwpipe1 --- LM0 -- DSPP0
- - \
- -- 3D Mux -- INTF0 -- HDMI
- - /
hwpipe2 --- LM1 -- DSPP1
hwpipe1 is staged on the 'left' Layer Mixer, and hwpipe2 is staged on
the 'right' Layer Mixer. An additional block called the '3D Mux' is
used to merge the output of the 2 DSPPs to a single interface.
In this use case, it is possible that a 4K surface is downscaled and
placed completely within one of the halves. In order to support such
scenarios (and keep the programming simple), Layer Mixers with Source
Split can be assigned 2 hw pipes per stage. While scanning out, the HW
takes care of fetching the pixels fom the correct pipe.
Add a MDP cap to tell whether the HW supports source split or not.
Add a MDP LM cap that tells whether a LM instance can operate in
source split mode (and generate the 'left' part of the display
output).
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
These are a part of CRTC state, it doesn't feel nice to leave them
hanging in mdp5_ctl struct. Pass mdp5_pipeline pointer instead
wherever it is needed.
We still have some params in mdp5_ctl like start_mask etc which
are derivative of atomic state, and should be rolled back if
a commit fails, but it doesn't seem to cause much trouble.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In the last few commits, we've been adding params to mdp5_crtc_state, and
assigning them in the atomic_check() funcs. Now it's time to actually
start using them.
Remove the duplicated params from the mdp5_crtc struct, and start using
them in the mdp5_crtc code. The majority of the references to these params
is in code that executes after the atomic swap has occurred, so it's okay
to use crtc->state in them. There are a couple of legacy LM cursor ops that
may not use the updated state, but (I think) it's okay to live with that.
Now that we dynamically allocate a mixer to the CRTC, we can also remove
the static assignment to it in mdp5_crtc_init, and also drop the code that
skipped init-ing WB bound mixers (those will now be rejected by
mdp5_mixer_assign()).
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Things like vblank/err irq masks, mode of operation (command mode or not)
are derivative of the interface and mixer state. Therefore, they need to
be a part of the CRTC state too.
Add them to mdp5_crtc_state, and assign them in the CRTC's atomic_check()
func, so that it can be rolled back to a clean state.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The INTF and CTL used in a display pipeline are going to be maintained as
a part of the CRTC state (i.e, in mdp5_crtc_state).
These entities, however, are currently statically assigned to drm_encoders
(i.e. mdp5_encoder). Since these aren't directly visible to the CRTC, we
assign them to the CRTC state in the encoder's atomic_check() op.
With this approach, we assign portions of CRTC state in two different
places: the layer mixer in CRTC's atomic_check(), and the INTF and CTL
pieces in the encoder's atomic_check() op.
We'd have more options here if the drm core maintained encoder state too,
but the current approach of clubbing everything in CRTC's state works just
fine.
Unlike hwpipes and mixers, we don't need to keep a track of INTF/CTL
assignments in the global atomic state. This is because they're currently
not sharable resources. For example, INTF0 and CTL0 will always be assigned
to one drm_encoder. This can change later when we implement writeback and
want a CRTC to use a CTL for a while, and then release it for others to use
it. Or, when a drm_encoder can switch between using a single INTF vs
2 INTFs.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add the stuff needed to allow dynamically assigning a mixer to a CRTC.
Since mixers are a resource that can be shared across multiple CRTCs, we
need to maintain a 'hwmixer_to_crtc' map in the global atomic state,
acquire the mdp5_kms.state_lock modeset lock and so on.
The mixer is assigned in the CRTC's atomic_check() func, a failure will
result in the new state being cleanly rolled back.
The mixer assignment itself is straightforward, and almost identical to
what we do for hwpipes. We don't need to grab the old hwmixer_to_crtc
state like we do in hwpipes since we don't need to compare anything
with the old state at the moment.
The only LM capability we care about at the moment is whether the mixer
instance can be used to display stuff (i.e, connect to an INTF
downstream).
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Subclass drm_crtc_state so that we can maintain additional state for
our CRTCs.
Add mdp5_pipeline and mdp5_ctl pointers in the subclassed state.
mdp5_pipeline is a grouping of the HW entities that forms the downstream
pipeline for a particular CRTC. It currently contains pointers to
mdp5_interface and mdp5_hw_mixer tied to this CRTC. Later, we will
have 2 hwmixers in this struct. (We could also have 2 intfs if we want
to support dual DSI with Source Split enabled. Implementing that feature
isn't planned at the moment).
The mdp5_pipeline state isn't used at the moment. For now, we just
introduce mdp5_crtc_state and the crtc funcs needed to manage the
subclassed state.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The mdp5_ctl has an 'op_mode' struct which contains info on
the downstream pipeline.
Grouping these params together in a struct doesn't serve much
purpose in the code. Maybe there was a plan to expand this
further that never happened.
Remove the op_mode struct, and place its members directly in
mdp5_ctl. This will help avoid confusion later when I introduce
my own verion of a mdp5 pipeline :)
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
mdp5_interface struct contains data corresponding to a INTF
instance in MDP5 hardware. This sturct is memcpy'd to the
mdp5_encoder struct, and then later to the mdp5_ctl struct.
Instead of copying around interface data, create mdp5_interface
instances in mdp5_init, like how it's done currently done for
pipes and layer mixers. Pass around the interface pointers to
mdp5_encoder and mdp5_ctl. This simplifies the code, and allows
us to decouple encoders from INTFs in the future if needed.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
PingPong ID for a Layer Mixer is already contained in
mdp5_hw_mixer.
This avoids the need to retrieve PP ID using macros
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Use the mdp5_hw_mixer struct in the mdp5_crtc and mdp5_ctl instead of
using the LM index.
Like before, the Layer Mixers are assigned statically to the CRTCs.
The hwmixer(s) will later be dynamically assigned to CRTCs.
For now, ignore the hwmixers that can only do WB.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Create a struct to represent MDP5 Layer Mixer instances. This will
eventually allow us to detach CRTCs from the Layer Mixers, and
generally clean things up a bit.
This is very similar to how hwpipes were previously abstracted away
from drm planes.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The number of Layer Mixers and the downstream blocks (DSPPs and PPs)
connected to each LM can vary with different MDP5 revisions. These
parameters are also static.
Keep the per instance LM data in mdp5_cfg. This will avoid the need
to have macros which identify PP id or DSPP id the LM is connected
to. We don't configure DSPPs at the moment, but keeping the DSPP
instance # here might come handy later.
Also add a 'caps' field that identifies features supported by a
LM instance. Introduce the caps MDP_LM_CAP_DISPLAY and MDP_LM_CAP_WB
that identify whether a LM instance can be used for display or
writeback.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We'd previously moved the pipe_lock spinlock to the hwpipe struct. Bring
it back to mdp5_plane. We will need this because an mdp5_plane in the
future could comprise of 2 hw pipes. It makes more sense to have a single
lock to protect the registers for the hw pipes used by a plane, rather
than trying to take individual locks per hwpipe when committing a
configuration.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
4 macros already defined in hdmi.h,
which is not required to redefine in hdmi_audio.c
Signed-off-by: Vinay Simha BN <simhavcs@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
'SSPP_MAX + 1' is the max number of hwpipes that can be present on a
MDP5 platform. Recently, 2 new cursor hwpipes were added, which
caused overflows in arrays that used SSPP_MAX to represent the number
of elements. Update the SSPP_MAX value to incorporate the extra
hwpipes.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
A recent commit introduces a bug in dsi_mgr_phy_enable. In the non
dual DSI mode, we reset the mdsi (master DSI) PHY. This isn't right
since master and slave DSI exist only in dual DSI mode. For the normal
mode of operation, we should simply reset the PHY of the DSI device
(i.e. msm_dsi) corresponding to the current bridge.
Usage of the wrong DSI pointer also resulted in a static checker
warning. That too is resolved with this fix.
Fixes: b62aa70a98 (drm/msm/dsi: Move PHY operations out of host)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Zero sized buffer objects tend to make various bits of the GEM
infrastructure complain:
WARNING: CPU: 1 PID: 2323 at drivers/gpu/drm/drm_mm.c:389 drm_mm_insert_node_generic+0x258/0x2f0
Modules linked in:
CPU: 1 PID: 2323 Comm: drm-api-test Tainted: G W 4.9.0-rc4-00906-g693af44 #213
Hardware name: Qualcomm Technologies, Inc. DB820c (DT)
task: ffff8000d7353400 task.stack: ffff8000d7720000
PC is at drm_mm_insert_node_generic+0x258/0x2f0
LR is at drm_vma_offset_add+0x4c/0x70
Zero sized buffers serve no appreciable value to the user so disallow
them at create time.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Output the upper 32 bits of a 64 bit iova in the RD_CMDSTREAM_ADDR
section while maintaining backwards compatibility for tools that
only understand 32 bit iovas.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The interrupt status was being cleared before processing the handlers.
a5xx_rbbm_err_irq() was checking the interrupt status again, which would
likely turn out bad because the interrupt status would be 0 (or at least
different). Pass the original status to the function instead.
Also, skip clearing RBBM_AHB_ERROR from the interrupt status. The interrupt
will keep firing until the error source is cleared. Skip the clear to
avoid a storm until the error is cleared in a5xx_rbbm_err_irq().
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
priv->num_aspaces is increased and then checked to see if it still fits
in the priv->aspace array. If it doesn't, we warn and exit but
priv->num_aspaces remains incremented.
Don't incremement the count until we know that it fits in the array.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Instead of checking for a5xx_gpu->gpmu_iova during destroy we
accidently check a5xx_gpu->gpmu_bo.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The core takes care of handling the send_event vs. close() issues, we
can remove that driver code.
Cc: Rob Clark <robdclark@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
I didn't spot anything that would require ordering here (well not
anywhere else either), and I'm trying to unify at least modern drivers
on one close hook.
Cc: Rob Clark <robdclark@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The newly added a5xx support fails to build when debugfs is diabled:
drivers/gpu/drm/msm/adreno/a5xx_gpu.c:849:4: error: 'struct msm_gpu_funcs' has no member named 'show'
drivers/gpu/drm/msm/adreno/a5xx_gpu.c:849:11: error: 'a5xx_show' undeclared here (not in a function); did you mean 'a5xx_irq'?
This adds a missing #ifdef.
Fixes: b5f103ab98 ("drm/msm: gpu: Add A5XX target support")
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Probably a symptom of needing finer grained locking, but if we wait on
the incoming fence-fd (which could come from a different context) while
holding struct_mutex, that blocks retire_worker so gpu fences cannot get
signalled.
This causes a problem if userspace manages to get more than a frame
ahead, leaving the atomic-commit worker blocked waiting on fences that
cannot be signaled because submit is blocked waiting for a fence
signalled from vblank (after the atomic commit which is blocked).
If we start having multiple fence ctxs for the gpu, submit_fence_sync()
would probably need to move outside of struct_mutex as well.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Significantly simplifies things. Also iommu_unmap() can unmap an entire
iova range.
(If backporting to downstream kernel you might need to revert this. Or
at least double check older iommu implementation.)
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja