Added variable 'error' to struct dvb_ringbuffer, which is set to zero on
init() and flush(). Also reset read an write pointers to zero on flush()
to get less fragmented data.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes default values for some picture controls:
- brightness set to 50% by default (now is 0%)
- hue set to 50% by default (now is 0%)
- sets saturation to datasheet value
- volume set to 0dB (now is -32dB)
and some left small fixes:
- twice offset adding
- balance didn't follow datasheet (bits[0:5] = attenuation;
bit[6] = channel to provide attenuation)
Signed-off-by: Marcin Rudowski <mar_rud@poczta.onet.pl>
Signed-off-by: Ian Pickworth <ian@pickworth.me.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for the IR remote control found in the card
CX88_BOARD_PROLINK_PLAYTVPVR.
Signed-off-by: Matheus Izvekov <mizvekov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch changes the gpio0 values for the card CX88_BOARD_PROLINK_PLAYTVPVR
to the ones observed using RegSpy from the dscaler project.
Signed-off-by: Matheus Izvekov <mizvekov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Added support for AVerMedia A169 Dual Analog tuner card
(dual saa7134 decoders - only 1 working right now)
- Added autodetection for both parts of the card.
It shows up like 2 cards, B1 and B
- Enabled tuner B1, SVIDEO on B1 and composite1 through SVIDEO,
FIXME: B is more or less dead at this point and I suspect the
FM-radio is on the B part of the board
Signed-off-by: Rickard Osser <ricky@osser.se>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- added tuner_lg_taln_pal_secam_ranges
- renamed tuner 66 from TUNER_LG_NTSC_TALN_MINI to TUNER_LG_TALN
- updated FlyTV mini Asus Digimatrix with new tuner
Thanks-to: Rickard Osser <ricky@osser.se>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- matched indents on quotes within a printk
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some chipsets have several problems when pci to pci transfers are activated
on overlay mode. the option no_overlay allows disabling such feature of
the driver, in favor of keeping the system stable.
The default is to use pcipci_fail flag defined on drivers/pci/quirks.c.
It also allows the user to override it by forcing disable overlay or forcing
enable. Forcing enable may generate PCI transfer corruption, including disk
mass corruption, so should be used with care.
Added a text description to this option and make messages looks the same at
both bttv and saa7134 drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Used Lindent, manually changed some line breaks. Removed invalid email
addresses, useless casts and useless initialization of return values.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rename 'enum dmxdevype' to 'enum dmxdev_type' and use this enum instead
of int for the member 'type' of struct dmxdev_filter.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The member dvbdev gets initialized once but is never used after that.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The PID value is already stored in struct dmx_sct_filter_params which is
a member of struct dmxdev_filter.
Acked-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Old values generally works in A2 mono, but new ones allows:
- detect and use Nicam stereo
- mute in tv
- use radio FM
Signed-off-by: Marcin Rudowski <mar_rud@poczta.onet.pl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There is an error in the cx88 code that causes this message in the syslog when
balance is changed at full volume:
Mar 4 18:35:08 ian2 kernel: cx88[0]: irq pci [0x1] vid*
Mar 4 18:35:39 ian2 last message repeated 348 times
Mar 4 18:36:01 ian2 last message repeated 564 times
... and so on
The attached patch cures this problem.
Signed-off-by: Ian Pickworth <ian@pickworth.me.uk>
Signed-off-by: Marcin Rudowski <mar_rud@poczta.onet.pl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The Coverity checker (previously Stanford checker) noticed that
the value of nskips could be read even if it was never written.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Conflicts:
Documentation/video4linux/CARDLIST.cx88
drivers/media/video/cx88/Kconfig
drivers/media/video/em28xx/em28xx-video.c
drivers/media/video/saa7134/saa7134-dvb.c
Resolved as in the original merge by Mauro Carvalho Chehab
VIDEO_CX88_ALSA should not be between VIDEO_CX88_DVB and
VIDEO_CX88_DVB_ALL_FRONTENDS
When cx88-alsa was added to cx88/Kconfig, it was added in between
VIDEO_CX88_DVB and VIDEO_CX88_DVB_ALL_FRONTENDS. This caused
undesireable effects to the appearance of the menu options in
menuconfig.
This fix reorders cx88-alsa and cx88-dvb in Kconfig, to match saa7134,
and restore the correct menuconfig appearance.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fixed em28xx based system lockup, device needs to be initialized before
starting the isoc transfer otherwise the system will completly lock up.
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The behaviour of the all-in-one Video4Linux tuner driver apparently
changed. It now wants to know the tv standard, otherwise it refuses to
tune.
Restore tuning functionality in my driver for the "Multimedia eXtension
Board". The all-in-one tuner driver apparently changed its behaviour.
Signed-off-by: Michael Hunold <hunold@linuxtv.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Typos grab bag of the month.
Eyeballed by jmc@ in OpenBSD.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Workaround for Nexus CA: Debi test fails unless first debi write is repeated.
Signed-off-by: Marco Schluessler <marco@lordzodiac.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch makes three needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I have the same card with the same PCI id, but from KWorld.
The patch documents that this is the same card.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Typos grab bag of the month.
Eyeballed by jmc@ in OpenBSD.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- The tuner used in DViCO FusionHDTV DVB-T hybrid is made by Thomson
- renamed tuner and dvb_pll structs accordingly
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The init_data array is never changed and need not be on the stack.
Turn it into a static variable.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- VIDEO_CX88_DVB_ALL_FRONTENDS should select DVB_ZL10353
- created VIDEO_CX88_DVB_ZL10353, for selective zl10353 support in cx88-dvb.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for the FE6600 tuner used on the DVB-T Hybrid board.
Add support for the Zarlink ZL10353 DVB-T demodulator, which supersedes the
MT352, used on the DViCO FusionHDTV DVB-T Hybrid and later model Plus boards.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use refactored LNBP21/BSBE1 code for Technotrend/Hauppauge DVB-S rev 2.3.
As a side effect, FE_ENABLE_HIGH_LNB_VOLTAGE ioctl is supported now.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Moved duplicated code to separate files.
LNBP21 stuff rewritten from scratch, BSBE1 copied from av7110.c.
Modified budget driver to use the new routines.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Workaround for Nexus CA: Debi test fails unless first debi write is repeated.
Signed-off-by: Marco Schluessler <marco@lordzodiac.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- fixed tda9886 port 2 setting
- turned remote control receiver off via saa7134 GPIO to avoid i2c hangs
- modified tda9886 client calls to direct i2c access to allow proper return
to analog mode
- allow mode change to V4L2_TUNER_DIGITAL_TV in tuner VIDIOC_S_FREQUENCY
client call
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- ELSA EX-VISION 500TV was incorrectly programmed to have the same
subsystem ID as ELSA EX-VISION 300TV, (1048:226b)
- This changeset replaces the incorrect subsystem ID (1048:226b)
with the correct one (1048:226a) for the ELSA EX-VISION 500TV.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I have a TT C1500 card (saa7146, STV0297) which had problems tuning
channels at QAM128 (like the ones in the Finnish HTV / Welho network).
A fix which seems to work perfectly so far is to change the delay for
QAM128 to the same values as for QAM256 in stv0297_set_frontend(),
Signed-off-by: Mattias Nordstrom <nordstrom@realnode.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
use __devinit/__devexit/__devexit_p() where appropriate
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The probing code for tda8290 changes the state of the tda9887 GP ports.
The patch assumes that if probing for tda8290 failed, this must be a
tda9887 and restores its power on defaults.
This should solve the module load order issue with some pinnacle cards.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The following are specific to lgdt3303, and are being renamed to reflect this.
- cxusb_lgdt330x_config renamed to cxusb_lgdt3303_config.
- cxusb_lgdt330x_frontend_attach renamed to cxusb_lgdt3303_frontend_attach.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When multiple cards were installed, only the first card would have
audio initialized, because only the first position in the array parameter
defaulted to "1"
To make things worse, the "enable" parameter wasn't enabled, so there
was no workaround.
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds another composite input to the Pinnacle PCTV 100i
definition which filters the chrominace signal from the luma input. This
improves video quality for Composite signals on the S-Video connector of
the card.
In addition the name string of the card is changed to include PCTV 40i
and 50i since these cards are identical.
Signed-off-by: Karsten Suehring <ksuehring@gmx.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch contains the following possible cleanups:
- update the Kconfig help to mention the VP310
- merge vp310_attach and mt312_attach into a new vp310_mt312_attach
to remove some code duplication
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- make 2 needlessly global functions static
- remove cpia2_setup(): the driver already allows setting parameters
through module_param(), and there's no reason for having two different
ways for setting the same parameters
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Moved keymaps to the ir-common module, and export them from there, instead
of #including them in each module
Included missing files from V4L/DVB(3197).
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- ELSA EX-VISION 500TV was incorrectly programmed to have the same
subsystem ID as ELSA EX-VISION 300TV, (1048:226b)
- This changeset replaces the incorrect subsystem ID (1048:226b)
with the correct one (1048:226a) for the ELSA EX-VISION 500TV.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- fixed tda9886 port 2 setting
- turned remote control receiver off via saa7134 GPIO to avoid i2c hangs
- modified tda9886 client calls to direct i2c access to allow proper return
to analog mode
- allow mode change to V4L2_TUNER_DIGITAL_TV in tuner VIDIOC_S_FREQUENCY
client call
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes the strange crashes I was seeing after using
bttv card, caused by a buffer overflow in bttv_risc_packed.
The instruction buffer size calculation contains two errors:
(a) a non-zero padding value can push the start of the next bpl
section to just before a page border, leading to more scanline
splits and thus additional instructions.
(b) the first DMA region can be smaller than one page, so there can
be a scanline split even if bpl*lines is smaller than PAGE_SIZE.
For example, consider the case where offset is 0, bpl is 2, padding
is 4094, lines is smaller than 2048, the first DMA region has size 1
and all others have size PAGE_SIZE, assumed to equal 4096. Then
all bpl regions cross page borders and the number of instructions
written is 2*lines+2, rather than lines+2 (the current estimate).
With this patch the number of instructions for this example is
estimated to be 2*lines+3.
Also, the BUG_ON that was supposed to catch buffer overflows contained
a thinko causing it fire only if the buffer was overrun by a factor of
16 or more, so it fixes the the BUG_ON's (using sizeof rather than "4").
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- fix temporary debug code by changing printk to dprintk at level 1.
- move CORE_IOCTL messages from level 1 to level 2.
- this should help with selective debugging,
while not filling people's logs up during normal use.
Signed-off-by: Ian Pickworth <ian@pickworth.me.uk>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Current xc3028 support is still experimental, requiring more work to be
sent to mainstream. It will be kept only at mercurial tree on
http://linuxtv.org/hg until fixed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
After a FIFO corruptions occurrs (generally due to buffer overflow), FIFO
contents needs to be discarted.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Now, root may change parameters while module is running.
Thanks to Edgar Toerning
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fixed broken IF-OUT on pinnacle sat board.
Thanks to Edgar Toernig
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ignore invalid messages on cx24110 frontend.
Thanks to Edgar Toernig
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The field "dvr" in struct dmxdev is competely unused. Remove
it and code which allocates, initializes and frees it.
Signed-off-by: Peter Beutner <p.beutner@gmx.net>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
use __devinit/__devexit/__devexit_p() where appropriate
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I have a TT C1500 card (saa7146, STV0297) which had problems tuning
channels at QAM128 (like the ones in the Finnish HTV / Welho network).
A fix which seems to work perfectly so far is to change the delay for
QAM128 to the same values as for QAM256 in stv0297_set_frontend(),
Signed-off-by: Mattias Nordstrom <nordstrom@realnode.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The probing code for tda8290 changes the state of the tda9887 GP ports.
The patch assumes that if probing for tda8290 failed, this must be a
tda9887 and restores its power on defaults.
This should solve the module load order issue with some pinnacle cards.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There has been a CPIA2 driver out of kernel for a long time and it has
been pretty clean for some time too. This is an import of the
sourceforge driver which has been stripped of
- 2.4 back compatibility
- 2.4 old style MJPEG ioctls
A couple of functions have been made static and the docs have been
repackaged into Documentation/video4linux. The rvmalloc/free functions now
match the cpia driver again. Other than that this is the code as is.
Tested on x86-64 with a QX5 microscope.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Previously, only NTSC and PAL/M were associated to 30fps and
525 lines, so, PAL/60 were not handled properly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added a new function that allows printing ioctl arguments.
This makes easier to include debug code under v4l ioctl
handling.
Also fixed some declarations on internal ioctl.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The remote controller on the LifeView FlyDVB-T Duo card work flawlessly
with the same settings as the LifeView FlyDVB-T LR301 card.
Signed-off-by: Rudo Thomas <rudo@matfyz.cz>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Standard video using the cx88 broadcast decoder is
working, but blackbird isn't working yet, audio is only
working correctly for television mode. S-Video and Composite
are working for video-only, so I have them disabled for now.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Enable the tuv1236 tuner on the Kworld-ATSC110 card so that the
tuner can be identified when tuners.ko loads.
- With this change it is no longer necessary to remove and reload
the tuner module in order to get the tuv1236 identified.
- This code was copied from the ATI HDTV Wonder init routine (in cx88-cards.c)
which also uses the TUV1236D.
Signed-off-by: Curt Meyers <cmeyers@boilerbots.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- There is no radio with this tuner card...
Thanks-to: Dwaine Garden <DwaineGarden@rogers.com>
- fixed capitalization in card name.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- When tuning VSB, use ANT input
- When tuning QAM, use CABLE input
Signed-off-by: Curt Meyers <cmeyers@boilerbots.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The following are specific to lgdt3303, and are being renamed to reflect this.
- cxusb_lgdt330x_config renamed to cxusb_lgdt3303_config.
- cxusb_lgdt330x_frontend_attach renamed to cxusb_lgdt3303_frontend_attach.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The remote control interface for this board is the same as the one for
BTTV_BOARD_CONCEPTRONIC_CTVFMI2
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When multiple cards were installed, only the first card would have
audio initialized, because only the first position in the array parameter
defaulted to "1"
To make things worse, the "enable" parameter wasn't enabled, so there
was no workaround.
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds another composite input to the Pinnacle PCTV 100i
definition which filters the chrominace signal from the luma input. This
improves video quality for Composite signals on the S-Video connector of
the card.
In addition the name string of the card is changed to include PCTV 40i
and 50i since these cards are identical.
Signed-off-by: Karsten Suehring <ksuehring@gmx.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for ELSA EX-VISION 700TV, which is the ELSA Japan's
flagship model of the software encoding TV capture card.
All inputs (Television, Composite1 and S-Video) have been tested.
Signed-off-by: Tamuki Shoichi <tamuki@linet.gr.jp>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- add radio support for KWorld HardwareMpegTV XPert
- fix GPIO settings for tv and radio
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch contains the following possible cleanups:
- update the Kconfig help to mention the VP310
- merge vp310_attach and mt312_attach into a new vp310_mt312_attach
to remove some code duplication
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- remove tuner.ko build dependency on xc3028.o , which will be added again later.
- fix the following build error when using the "make kernel-links" build method to
symlink the latest code from the v4l-dvb repository into the kernel source:
drivers/media/video/xc3028.c:31:20: em28xx.h: No such file or directory
drivers/media/video/xc3028.c: In function `xc3028_init':
drivers/media/video/xc3028.c:120: error: dereferencing pointer to incomplete type
drivers/media/video/xc3028.c:121: error: dereferencing pointer to incomplete type
drivers/media/video/xc3028.c:139: error: dereferencing pointer to incomplete type
drivers/media/video/xc3028.c:140: error: dereferencing pointer to incomplete type
make[3]: *** [drivers/media/video/xc3028.o] Error 1
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Current xc3028 support is still experimental, requiring more work to be
sent to mainstream. So, it was marked inside some defines, in order to be
removed by gentree.pl stript. Script also updated to remove it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fixed xc3028 firmware extractor for terratec's emBDA.sys firmware
Fixed delay in firmwareupload, now terratec's firmware also works
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added support for xc3028 to v4l which adds support for:
* Terratec Hybrid XS (analogue)
* Hauppauge HVR 900 (analogue)
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
* compat_alloc_user_space() returns __user pointer
* copying between two userland areas is copy_in_user(), not copy_from_user()
* dereferencing userland pointers is bad
* so's get_user() from local variables
... plus usual __user annotations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Adding support for Terratec Prodigy XS
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
disabled debug on by default in tvp5150
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Forgot to take the NTSC frequency offset into account.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The at76c651 and tda80xx frontends are currently completely unused, IOW
their only effect is making the kernel larger for people accitentially
enabling them.
The current in-kernel drivers differ from the drivers at cvs.tuxbox.org,
and re-adding them when parts of the dbox2 project get merged should be
trivial.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- When a firmware was downloaded dvb_usb_device_init returns NULL for the
dvb_usb_device, then nothing should be done with that pointer and device,
because it will re-enumerate.
- A new firmware should be used with digitv devices.
- It should make "slave"-devices work and others, too.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Reassigning function pointers in a static led to infinite loops when using
multiple VP7045-based device at the same time on one system. Using kmalloc'd
copies for reassignments is better.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use the parallel transport function of the MT352 demodulator in
TH7579 and LGZ201 -based FusionHDTV Bluebird usb boxes.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use the parallel transport function of the MT352 in USB demodulator of the
Dual Digital board.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The at76c651 and tda80xx frontends are currently completely unused, IOW
their only effect is making the kernel larger for people accitentially
enabling them.
The current in-kernel drivers differ from the drivers at cvs.tuxbox.org,
and re-adding them when parts of the dbox2 project get merged should be
trivial.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Add initial support for KWorld HardwareMpegTV XPert.
- uses silicon tuner: tda8290 + tda8275
- standard video using cx88 broadcast decoder is working.
- blackbird mpeg encoder support (cx23416) not yet working.
- FM radio untested.
- audio is only working correctly in television mode,
all other modes disabled.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is an analog / digital hybrid card.
Signed-off-by: Peter Hartshorn <p3r@users.sourceforge.net>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fixed em28xx based system lockup, device needs to be initialized
before starting the isoc transfer otherwise the system will completly lock up.
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- When a firmware was downloaded dvb_usb_device_init returns NULL for the
dvb_usb_device, then nothing should be done with that pointer and device,
because it will re-enumerate.
- A new firmware should be used with digitv devices.
- It should make "slave"-devices work and others, too.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Reassigning function pointers in a static led to infinite loops when using
multiple VP7045-based device at the same time on one system. Using kmalloc'd
copies for reassignments is better.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use the parallel transport function of the MT352 demodulator in
TH7579 and LGZ201 -based FusionHDTV Bluebird usb boxes.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use the parallel transport function of the MT352 in USB demodulator of the
Dual Digital board.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Analog and DVB-T are working, Remote not yet.
This card is based on the new LifeView design, there should be many variants.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Set outputs to tristate in sleep mode
- Reduce dangerously high firmware download speed with 16MHz xtal
- added tda827x configuration with GPIOs low
- added comments to stupid looking IIC reads that work around bugs in
the tda10046.
- some minor updates
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch
- works around a bug in the I2C bridge that makes the initialization
of the TDA10046 fail on recent LifeView cards
- puts the AGC output to tristate in sleep mode. This is necessary for
recent hybrid cards that switch the AGC via tristateing.
Signed-off-by: Hartmut Hackmann<hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Additionally to the card support, this changeset adds the option
tda10046lifeview to get_dvb_firmware to download tda10046 firmware
from LifeView's site.
Signed-off-by: Giampiero Giancipoli <gianci@libero.it>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
South Korea uses NTSC-M but with A2 audio instead of BTSC. Several audio
chips need this information in order to set the correct audio processing
registers.
Acked-by: Mauro Carvalho Chehab <mauro_chehab@yahoo.com.br>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
South Korea uses NTSC-M but with A2 audio instead of BTSC. Several audio
chips need this information in order to set the correct audio processing
registers.
Acked-by: Mauro Carvalho Chehab <mauro_chehab@yahoo.com.br>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
add IR support to KWorld DVB-T (cx22702-based)
Signed-off-by: Marco Manenti <marco_manenti@colman.it>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- rename DVB_USB_CXUSB one-liner description to:
Conexant USB2.0 hybrid reference design support.
- with the addition of bluebird support to dvb-usb-cxusb,
it now depends on lgdt330x and mt352 modules.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
add IR support to KWorld DVB-T (cx22702-based)
Signed-off-by: Marco Manenti <marco_manenti@colman.it>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- added signal detection support to tvp5150
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- added signal detection support to tvp5150
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Apparently, having the number of lines fixed at 4 reduces (or even kills)
the buzz found in NICAM stereo with analog sound.
Signed-off-by: Marcin Rudowski <mar_rud@poczta.onet.pl>
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- rename DVB_USB_CXUSB one-liner description to:
Conexant USB2.0 hybrid reference design support.
- with the addition of bluebird support to dvb-usb-cxusb,
it now depends on lgdt330x and mt352 modules.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
With tuner_debug enabled, if a tuner tries to use a video standard that doesn't
have a matching tuner_params defined, the IFPCoff value and tuner number will
be displayed, and the default tuner_params entry will be used.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If a given tuner definition contains more than one tuner_params array members,
it will try to select the appropriate tuner_params based on the video standard
in use. If there is no tuner_params defined for the current video standard, it
will select the default, tuner_params[0]
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch allows to select AM sound even if NICAM is detected.
Proposed by Alain Frappin
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Right now, all tuners are using the first tuner_params[]
array element for analog mode. We are now ready to begin merging
similar tuner definitions together, such that each tuner definition
will have a tuner_params struct for each available video standard.
The tuner_params[] array element will be chosen based on the video
standard in use.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- tuner_dbg will show tuner param and range selected
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- allow multiple tuner params in each tuner definition.
- the correct tuner_params element will be chosen based on
current video standard.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- move video std detection to top of set_tv_freq function
- we must detect video std first, so that we can choose the correct
tuner_params
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Apparently, having the number of lines fixed at 4 reduces (or even kills)
the buzz found in NICAM stereo with analog sound.
Signed-off-by: Marcin Rudowski <mar_rud@poczta.onet.pl>
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The tuner_params element is an array of undefined length,
with each array member being a set of parameters for each
video standard type.
The number of members in the tuner_params array
will be stored in tuners[]->count
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
memset clears once set structure, there is actually no need for memset,
because configure function do it for us. Next, vfree(NULL) is legal, so
avoid useless labels.
Thanks Dave Jones for reporting this.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
memset clears once set structure, there is actually no need for memset,
because configure function do it for us. Next, vfree(NULL) is legal, so
avoid useless labels.
Thanks Dave Jones for reporting this.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Fix printk type warning:
drivers/media/dvb/b2c2/flexcop-pci.c:164: warning:
format '%08x' expects type 'unsigned int', but argument 4 has type 'dma_addr_t'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Move config byte from tuner_params to tuner_range struct.
- dvb tuners must be able to set different config byte for each range.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- rename cb variable names in tuner structures for global consistency
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Fix printk type warning:
drivers/media/dvb/b2c2/flexcop-pci.c:164: warning:
format '%08x' expects type 'unsigned int', but argument 4 has type 'dma_addr_t'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- default_tuner_init was called twice due to a missing break statement.
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Acked-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Make needlessly global code static
- #if 0 the following unused global functions:
- b2c2/flexcop-dma.c: flexcop_dma_control_packet_irq()
- b2c2/flexcop-dma.c: flexcop_dma_config_packet_count()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Fixed VBI compilation.
- Included capacity to specify vbi and video number.
- Added a better control for using more than one em28xx device.
- VIDIOC_G_FMT now calls a function.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Moved some hardcoded minor numbers to videodev2.h
- Included more comments for sliced VBI standards
- Included some VBI macros to group similar standards
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- The tda9887 has an I2C id reserved for it, but it hasn't been using
it. Probably an oversight. Fixed with this patch.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- make VP-3054 Secondary I2C Bus Support a Kconfig option.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Kill nxt2002 module in favor of nxt200x.
- Repair broken nxt2002 support in the nxt200x module.
- Make the flexcop driver use nxt200x instead of the nxt2002 module for the
Air2PC 2nd generation PCI card.
- Remove the nxt2002 module from cvs and kernel build.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Mark Typhoon cards as OEM of Lifeview.
Signed-off-by: Peter Missel <peter.missel@onlinehome.de>
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Added other sliced VBI types to videodev2.h
- tvp5150 now uses standard V4L2 API codes from videodev2.h
- Implemented VIDIOC_G_SLICED_VBI_CAP for tvp5150. This is
dynamically filled based on defined VDP C-RAM values filled
by the driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Renamed some registers and improved register debug message
- Some cleanups at register dump
- Added code to set VBI processor (VDP)
- VBI code still incomplete
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Added credits for sn9c102 kernel module and his author as
some parts of em28xx-video were based.
Acked-by: Luca Risolia <luca.risolia@studio.unibo.it>
Acked-by: Markus Rechberger <mrechberger@gmail.com>
Acked-by: Ludovico Cavedon <cavedon@sssup.it>
Acked-by: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- default_tuner_init was called twice due to a missing break statement.
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Acked-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Make needlessly global code static
- #if 0 the following unused global functions:
- b2c2/flexcop-dma.c: flexcop_dma_control_packet_irq()
- b2c2/flexcop-dma.c: flexcop_dma_config_packet_count()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- The tda9887 has an I2C id reserved for it, but it hasn't been using
it. Probably an oversight. Fixed with this patch.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- make VP-3054 Secondary I2C Bus Support a Kconfig option.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Kill nxt2002 module in favor of nxt200x.
- Repair broken nxt2002 support in the nxt200x module.
- Make the flexcop driver use nxt200x instead of the nxt2002 module for the
Air2PC 2nd generation PCI card.
- Remove the nxt2002 module from cvs and kernel build.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Mark Typhoon cards as OEM of Lifeview.
Signed-off-by: Peter Missel <peter.missel@onlinehome.de>
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Tvp5150 type were determined by a secondary register instead of
using ROM code.
- tvp5150am1 have ROM=4.0, while tvp5150a have ROM=3.33 (decimal).
All other ROM versions are reported as unknown tvp5150.
- Except for reporting, current code doesn't enable any special feature
for tvp5150am1 or tvp5150a. Code should work for both models (but were
tested only for tvp5150am1).
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Add probe check for the tda9840 to prevent misdetection of a Micronas
dpl3518a as a tda9840.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Added credits for sn9c102 kernel module and his author as
some parts of em28xx-video were based.
Acked-by: Luca Risolia <luca.risolia@studio.unibo.it>
Acked-by: Markus Rechberger <mrechberger@gmail.com>
Acked-by: Ludovico Cavedon <cavedon@sssup.it>
Acked-by: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Tvp5150 type were determined by a secondary register instead of
using ROM code.
- tvp5150am1 have ROM=4.0, while tvp5150a have ROM=3.33 (decimal).
All other ROM versions are reported as unknown tvp5150.
- Except for reporting, current code doesn't enable any special feature
for tvp5150am1 or tvp5150a. Code should work for both models (but were
tested only for tvp5150am1).
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Add probe check for the tda9840 to prevent misdetection of a Micronas
dpl3518a as a tda9840.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Fix handling of VIDIOC_G_TUNER audmode in msp3400: audmode
is only changed by the user with S_TUNER, never by the driver.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Remove duplicated keymaps and add keymap for KWorld LTV883IR.
Thanks to Jon Ferguson <jon@sd-6.org>.
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- All the keymaps have the same structure, and can be shared between different
chips, so it makes no sense having them scattered between the input files.
This aggregates them all at ir-common module.
- Added new Hauppauge remote (Hauppauge grey), contributed by J.O. Aho
<trizt@iname.com> (with some small changes)
Changed KEY_KPx (keypad numerals) references to KEY_x, to avoid problems
when NumLock is off (suggested by Peter Missel <peter.missel@onlinehome.de>)
- Some cleanups at IR code
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- For the Hauppauge PVR cards there are at least two different remotes, one
completly black and one that is Grey and black, they keys differ in values
eg Black remotes 'mute' has the same value as Grey remotes 'menu'.
- This enables the user to select which keymapping to use by using the
hauppauge parm. Unlike to the black remote keys, all keys are
mapped for the grey remote and the ATi usb remote mappings has been
followed.
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Added remote control support for pinnacle pctv
Signed-off-by: Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Moved MSP_SET_MATRIX to v4l2-common.h
- Fix typos and integer overflows in tea5767.c
- Split old freq field into a tv_freq and a radio_freq. Prevents
that a radio tuner is initialized with a tv frequency or vice versa.
- When switching to radio mode initialize the tuner with the last
used radio frequency (this was already done for the TV mode).
As a result of these changes the tuner module now remembers the
last set radio and TV frequencies, which is what you would expect
to happen.
- Move out of range frequencies to the closest valid frequency as per
v4l2 API spec.
- Fix incorrect initial radio frequency (multiplier is 16000, not 16)
- Add boundary check for out of range frequencies.
- Use new flag to check if the order of the CB and freq. depends on
the last set frequency. That is needed for some tuners or you can
get static as a result. The flag is added for those tuners where I know
that the datasheet indicates that this is necessary.
- For this new check use the last set div value, not the last frequency
as radio frequencies are always much higher due to the 16000 multiplier.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix the following warning which was introduced in 2.6.15-git8 by
commit 7408187d223f63d46a13b6a35b8f96b032c2f623:
CC [M] drivers/media/video/zoran_card.o
drivers/media/video/zoran_card.c: In function `zr36057_init':
drivers/media/video/zoran_card.c:1053: warning: assignment makes integer from pointer without a cast
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Not sure what went wrong here, but SND_PCI_PM_CALLBACKS got deleted.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- BOOT_SIZE name is also used at alpha and were breaking
compiling with allyesconfig.
- All BOOT_* renamed to AV7110_BOOT* to fix and keep names
with the same style.
Thanks to Andrew Morton for pointing this.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Workaround to fix a known regression at cx88-tvaudio.c
- provide a module parameter workaround to always enable
analog output.
Signed-off-by: Panagiotis Christeas <p_christ@hol.gr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- This patch makes some needlessly global code static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Enabled audio PLL. This is mandatory for NICAM sound
- modify FM IF frequency to 5.5MHz for SAA7133/35 if tuner is tda8290
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Remove the "inline" keyword from a bunch of big functions in the kernel with
the goal of shrinking it by 30kb to 40kb
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Add support for Samsung tuner TCPN 2121P30A, used in
Hauppauge PVR-500 cards.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Tunertype struct redefined to allow one or more tuner_params structs
per tuner definition, one for each video standard.
- Each tuner_params struct has an element containing an arbitrary
amount of tuner_ranges.
(this is needed for dvb tuners - to be handled later)
- A tuner_range may be referenced by multiple tuner_params structs.
There are many duplicates in here. Reusing tuner_range structs,
rather than defining new ones for each tuner, will cut down on
memory usage, and is preferred when possible.
- tunertype struct contains an element, has_tda988x.
We must set this for all tunertypes that contain a tda988x
chip, and then we can remove this setting from the various
card structs.
- Improves tuners array memory usage efficiency.
- Right now, all tuners are using the first tuner_params[] array element
for analog mode. In the future, we will be merging similar tuner
definitions together, such that each tuner definition will have a
tuner_params struct for each available video standard. At that point,
the tuner_params[] array element will be chosen based on the video
standard in use.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
build-tested.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Static vars are equal to zero by default. Removed unnecessary =0 from them,
saving some data space
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- There's no reason for an ALSA driver to select an OSS legacy userspace
interface.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Adds suppport or fix support for VIDIOC_ENUMSTD, VIDIOC_ENUMINPUT,
VIDIOC_G_TUNER and VIDIOC_S_TUNER.
- Fix the warnings at compile time and add checks for the pointer validity
using access_ok().
- v4l_print_ioctl() has also be added to identify possible missing ioctls.
- Has been tested on sparc64 and amd64. Other arches such as mips and hppa
are expected to work as sparc, but not tested yet.
Signed-off-by: Guy Martin <gmsoft@tuxicoman.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Added knc1 tv star dvb-s support with philips tuner sd1878.
Signed-off-by: Regis Prevot <regis.prevot@anevia.com>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Added USB ID for DigitalNow DVB-T Dual USB,
DViCO FusionHDTV DVB-T Dual USB clone
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Debug var renamed to cx25840 to avoid conflicts with other
var with the same name at kernel
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Debug global var is already used inside kernel, so renamed
debug to tuner_debug for the tuner module
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Debug global var is already used inside kernel.
- v4l_dbg now expects the debug var
- global vars inside msp34xx renamed to msp_*
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Unused function removed.
Used container_of instead of for loop.
Some small changes
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Pci probing functions added, some functions were rewritten.
- Use PCI_DEVICE macro.
- dev_ used for printing when pci_dev available.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The call to i2c_add_driver() may actually fail, but tuner-3036 ignores
this and always returns 0, regardless.
Fix it up so it returns what i2c_add_driver() does, instead.
Signed-off-by: Arthur Othieno <a.othieno@bluewin.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- The Pinnacle 300i (like the PCTV Stereo) needs tda9887 port2 set to 1 for
the tuner to work
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Add support for DViCO FusionHDTV DVB-T USB devices
(Thomson dtt7579 and LG z201 based)
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Add a missing case which was preventing the operation of the HVR1100
remote.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
fops is used for module handling with ownership.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
video_device.priv is not allowed to touch and it will be actually removed in
near future. Use video_get_drvdata() instead.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Pci probing functions added, some functions were rewrited.
- Use PCI_DEVICE macro.
- dev_* used for printing when pci_dev available.
- some static variables changed to dynamicto allow operation with multiple
cards.
- Deleted macros for DEVICE_IDS, they are in pci_ids.h yet.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Clean up a recently introduced spaces vs tabs whitespace problem.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Move the code that patches bluebird firmware before upload from the
generic code into the cxusb driver itself.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Add VIDIOC_LOG_STATUS to the radio device ioctl list.
- Reduce the confusion between modes and standards
- Fix stereo reporting for radio.
- Don't set i2c configuration if the chip doesn't support it.
- Fix reporting of current standard for radio.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Implemented v4l2 api for sliced vbi data output
to pass WSS data from userspace to the av7110
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Check capabilities for audio settings (volume, balance,
bass, treble, loudness, mute)
- added loudness support
- added missing VIDEO_AUDIO_BALANCE flags for v4l1 compatibility
- do not call msp_any_detect_stereo for non-autoselect chips to
retrieve the current stereo setting: that will temporarily mute
the sound. It is only needed when the stereo mode might be
changed, and for autoselect msp processors that do not periodically
need to update their stereo setting.
- do not wake up the thread if the standard did not change. Prevents
temporary audio drop-out if the standard is set to the same value.
- fix confused stereo detect code where V4L2_TUNER_SUB_STEREO and
V4L2_TUNER_MODE_STEREO values were used incorrectly.
- stereo mode reporting was broken (v4l2 value used to index a
string array expecting v4l1 mode values).
- do not set dsp register 0x30 in the 3410d thread: that register
does not exist for pre-'G' revision msp chips.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- A new Kconfig option makes the user able to select if the dibusb-mb driver shall claim faulty programmed USB devices which are coming with default Cypress USB IDs.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Check if in the dvb-usb-device-structure the dvb_pll_desc is set before use.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Indention for values of several request defines were not TabSized=8.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Fixes compiling warning on kernel 2.6.15 with the Intel C compiler.
- It said drivers/media/dvb/frontends/bcm3510.c(258):
warning #592: variable "ret" is used before its value is set
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Replace old norm by the v4l2_std_id values.
- Add code to correctly detect the various capabilities of the
various msp chips. It's not yet used, that's going to be the next step.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- My original settings for this board were incorrect and resulted in
an increased number of signal dropouts. Replace this with the settings
from the Windows driver.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Add support for the remote control receiver inside the DViCO FusionHDTV
DVB-T Dual Digital, and a keymap for the MCE remote bundled with it.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Support for DVB reception on the PCI half of the DViCO DVB-T Dual Digital.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Add support for the USB portion of the DViCO Dual Digital board.
Patch correct "warm" USB IDs into bluebird firmware before download.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Saa7134-core.c saa7134_irq(): Separate GPIO16 and GPIO18 handling. Call
IR-remote-GPIO handler only if the GPIO IRQ is "owned" by it. Added
infrastructure to branch out to a future I2C-IR IRQ handler.
saa7134-core.c saa7134_hwinit2(): Enable only the one GPIO pin and edge to
trigger an IRQ that is wired as keyup/keydown mask. IRQ will only be
generated for an actual key-down event.
saa7134-input.c flyvideo_codes[]: Replace numpad keys with normal ones. Put
meaning to mystery keys. Change some key definitions to have their functions
match their labels better. Fix typos.
saa7134-input.c flydvb_codes[]: Added new table for the larger remote that
comes with the LifeView FlyDVB series.
saa7134-input.c build_key(): In IRQ mode, signal key-down and then key-up
straight in one go.
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Replaces old debug msgs from bt832, tda743d and tda9875 to newer ones
as defined under v4l2-common.h.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Both AverTV Studio 303 cards, #6 and #36,
use the same remote control programming.
Signed-off-by: George Gazurkoff <gazurkoff@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- There is a bug in the ioctl translations from 32bit userspace
to 64bit kernelspace in do_set_window().
- The video window (vw) should be passed to native_ioctl()
instead of the video clip.
Signed-off-by: Guy Martin <gmsoft@tuxicoman.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Add support for LifeView FlyDVB Trio.
- all analog inputs are supported and working, including FM radio
- TO DO: dvb & remote control
Signed-off-by: Peter Missel <peter.missel@onlinehome.de>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- This module is co-authored by Ricardo Cerqueira <v4l@cerqueira.org>.
- Added digital audio support for cx88-based boards that have function
01 enabled. These boards can be identified by having PCI id 1471:8801
or 1471:8811.
- Increased DMA buffer from 512 to 4096 seems to fix audio distortion.
- Existing audio DMA uses conflict with cx88-alsa. Should be disabled when
cx88-alsa module is compiled.
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Fix signed/unsigned bug in brightness handling (set to 0 and 128 was returned).
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Fix signed/unsigned bug in hue handling (set to -127 and 129 was returned).
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Add the fix for the saa7146 64-bit compile warning (again). This time with
comments and checked by Johannes Stezenbach.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Reverted objectionable fix in saa7146_hlp.c
- Merged in improved dvb 64-bit fixes from Peter Beutner.
Signed-off-by: Peter Beutner <p.beutner@gmx.net>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Add DViCO Bluebird firmware to dvb_get_firmware script,
for FusionHDTV USB devices.
- Use usb alt setting 0 for EP4 transfer (dvb-t),
- Use usb alt setting 7 for EP2 transfer (atsc)
- Added comment to lgdt330x.c to indicate support for
DViCO FusionHDTV5 USB Gold.
Thanks to: Jeff Lee <JeffLee@dvico.com>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- This property set is for the LG-H064F (FusionHDTV5 USB Gold)
- There may, in the future, be a bluebird device using a different NIM,
so renaming the struct to somehting NIM-specific is appropriate.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Improved recovery from ARM crash and the way a crash is detected.
Minor white space clean-up, debug output fixed.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Convert diagnostics over to the new v4l2-common.h macros.
- deprecated tuner_debug option, the new option is debug.
- renamed cx25840_debug to debug.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Added new v4l_err, v4l_warn, v4l_info and v4l_dbg macros to
v4l2-common.h for use in v4l-dvb i2c drivers. This ensures
a unique prefix for each device instance.
- At a later stage these macros may be reimplemented using the
device-generic macros from device.h.
- Converted the msp3400 driver to the new macros.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Split msp3400.c into msp3400-driver.c and msp3400-kthreads.c.
- Removed experimental DFPREG ioctls. If this is really needed one
day then it should be implemented using VIDIOC_G/S_REGISTER.
- Added missing BALANCE control info for VIDIOC_QUERYCTRL.
- Still more cleanup, clarified some kernel messages.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Continue cleanup effort:
- more cosmetic changes
- combine volume, balance, bass and treble into one audio
function. Revert old 2.4 code that crept in.
- print internal ioctls using new debug function.
- marked all msp3400c (aka manual) functions as such.
- removed some unused data structures.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Now, all internal ioctls are at v4l2-common.h
- removed unused ioctl at saa6752hs.h
- all debug ioctl code moved to v4l2-common.c
- removed duplicated stuff from other cards
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Now using firmware "dvb-usb-bluebird-01.fw",
with combined support for atsc and dvb-t Bluebird models.
- Use usb alt setting 0 for EP4 transfer (dvb-t),
- Use usb alt setting 7 for EP2 transfer (atsc) */
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Adds Bluebird ATSC support to the cxusb driver,
using dvb-usb-bluebird-atsc-01.fw firmware.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Step 1 of the msp3400.c cleanup.
Most changes are all cosmetic (moved code around, renamed functions
and variables).
New additions:
- VIDIOC_LOG_STATUS for debugging.
- More user friendly messages on driver load.
- 'simple' renamed to 'autodetect'
- 'simpler' renamed to 'autoselect'
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- A new firmware fixes VHF tuning issues. This changes the firmware file name in the driver.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Detect when AUDC_SET_RADIO is called.
- When in radio mode ignore VIDIOC_G_TUNER.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- When in radio mode don't do anything with VIDIOC_G_TUNER.
Allow other devices to fill this.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Don't reprogram the video standard if the new standard
equals the old standard.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- debug messages changed to be like the other modules
- Add V4L2 commands VIDIOC_S_TUNER, VIDIOC_G_TUNER,
VIDIOC_S_STD and VIDIOC_S_FREQUENCY.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Move signal strength level to the 0-65535 range as per V4L2 spec.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Added VIDIOC_S_AUDIO to set the audio inputs separately.
- Removed AUDC_SET_INPUT.
- Made the video inputs much more general.
- Removed cardtype CID and replaced with a CID to enable
the PVR150 workaround. The cardtype is no longer necessary
with the general video input change.
- Update VIDIOC_LOG_STATUS output to show the video and
audio inputs separately.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Calculate the audio master clock registers from the actual
frequencies. This simplifies the code and it also prepares
for adding CGC2 support.
- VIDIOC_INT_AUDIO_CLOCK_FREQ now receives an u32 instead of
an enum. It is more generic and actually easier to implement.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Replace AUDC_SET_INPUT with VIDIOC_S_AUDIO.
- Added V4L2_CID_AUDIO_MUTE.
- Minimum volume is -96 dB, not -90.
- Show volume in VIDIOC_LOG_STATUS.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- make the firmware dir documentation and comments consistent in the v4l-dvb tree.
Signed-off-by: Ville Skytt <ville.skytta@iki.fi>
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Create an array containing frequency threshold and control byte.
- allows for an arbitrary amount of
frequency ranges to be set, like dvb-pll.
- improves code readability.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Included advanced debug option to tvp5150.c
- Now, advanced debug info is the first item at V4L menu.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Created a new ioctl to control I2S speed. Old calls to an
inadequate V4L2 API replaced.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Now reset do init tvp5150 registers to its default.
- Debug messages improved.
- Implemented video standard selection function.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Added support for VP-3054 (aka DigitalNow DNTV Live! DVB-T Pro!).
- This board has a secondary I2C bus and remote control.
- Added a new module to handle secondary I2C bus on this board.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Added new ID for different revision of card #58. It's the same card,
but with a tda8275a instead of a tda8275
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Initialize the the dvb-usb-device-pointer in the -init function to NULL,
to be sure that a dvb-usb-device was really initialized.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- As far back as the video4linux cvs repository goes, there is no mention
of BTTV_TWINHAN_VP3021. It seems that this was done for the sake of
backwards compatability with some older v4l, but this can no longer be
necessary due to the v4l/dvb cvs merger, nor should this have ever
existed in the upstream kernel.
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- In the rare event that a 333MHz i2c firmware load fails after
writing some data, this fix makes the driver reset the DL_ADDR
registers to the proper values before continuing on with 100MHz
transfers.
Signed-off-by: Tyler Trafford <tatrafford@comcast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Corrected Thomson DTT 7611 tuner programming, based on spec sheet
- renamed to Thomson DTT 761x
- applies to DTT 7611 7611A 7612 7613 7613A 7614 7615 7615A
(DTT 7610 is similar, but slightly different programming)
- corrected frequency ranges for analog and digital modes
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- V4L2_(G|S|TRY)_FMT returned incorrect VBI start lines for PAL-M,
NTSC-JP, and PAL-60. They also returned an inaccurate VBI offset.
- V4L2_(G|S)_FMT and V4L2_TRY_FMT disagreed about the start of VBI
capturing in PAL and SECAM second field. Note the start line fixes
may break applications using VIDIOCSVBIFMT because this ioctl fails
when the driver does not support exactly the requested parameters.
- V4L2_TRY_FMT did not clear the reserved field in struct
v4l2_vbi_format.
- V4L2_(S|TRY)_FMT did not expect very large or small VBI start or
count values, returning wrong (but safe) counts due to an overflow.
- VIDIOCGVBIFMT confused V4L and V4L2 VBI flags. However this had no
effect because the flags have the same value and bttv never sets
them.
- In v4l_compat_translate_ioctl() the VIDIOC(G|S)VBIFMT code did not
expect V4L2 drivers supporting VBI formats besides V4L2_PIX_FMT_GREY.
Signed-off-by: Michael H. Schimek <mschimek@gmx.at>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Debug message changed to be coherent with other modules
- added ntsc parameter
- parameters moved to the beginning at the file
- tuner_status moved to a better position.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Now, default control values at cx88_cx8800_ctls are honored
- default value for contrast/saturation were changed to be
in line with available documentation for the chipset;
- Removed some bad coding at set_control;
- U/V Saturation now changes proportionally
Signed-off-by: Michael Krufky <mkrufky@m1k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Merged ir-kbd-gpio into bttv as bttv-input, for consistency with other
input modules
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Collection of patches from Peter Beutner addressing:
- add symbolrates to the DVB-S frontend description
- fix capability flags in DVB-S frontend describtion
- remove some void casts
- disable zig-zag scanning as it makes no sense for DVB-T
- set sensible min_delay value
- return an error for requested filter types the driver can't handle
Signed-off-by: Peter Beutner <p.beutner@gmx.net>
Signed-off-by: Alex Woods <linux-dvb@giblets.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- USB hot unplug Oops fix.
Signed-off-by: Deti Fliegl <deti@fliegl.de>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Here's a small patch to decrease the number of pointer derefs in
drivers/media/dvb/b2c2/flexcop-fe-tuner.c
Benefits of the patch:
- Fewer pointer dereferences should make the code slightly faster.
- Size of generated code is smaller
- Improved readability
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- digitv_ctrl_msg() if (wo) test is reversed. fixed.
- usb timeout is in Hz, not in jiffies.
- NULL replaced by 0 to be coherent.
- removed uneeded headers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Cleanup timeout handling in cx24123_pll_writereg(), and
use a reasonable value for the timeout.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
- Make FE_READ_UNCORRECTED_BLOCKS reset the count after each call,
thus returning a momentary value like all other demods do,
instead of an absolute, ever increasing count.
Signed-off-by: Stephen Williams <stephen.williams@gmail.com>
Signed-off-by: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Eric Sesterhenn