The Marvell Egress rx trailer check must be fixed to
correctly detect bad bits in the third byte of the
Eggress trailer as described in the Table 28 of the
88E6060 datasheet.
The current code incorrectly omits to check the third
byte and checks the fourth byte twice.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
rhashtable_rehash_one() uses complex logic to update entry->next field,
after INIT_RHT_NULLS_HEAD and NULLS_MARKER expansion:
entry->next = 1 | ((base + off) << 1)
This can be compiled along the lines of:
entry->next = base + off
entry->next <<= 1
entry->next |= 1
Which will break concurrent readers.
NULLS value recomputation is not needed here, so just remove
the complex logic.
The data race was found with KernelThreadSanitizer (KTSAN).
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converts the ch9200 driver to use the module_usb_driver() macro which
makes the code smaller and a bit simpler.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When support for megaflows was introduced, OVS needed to start
installing flows with a mask applied to them. Since masking is an
expensive operation, OVS also had an optimization that would only
take the parts of the flow keys that were covered by a non-zero
mask. The values stored in the remaining pieces should not matter
because they are masked out.
While this works fine for the purposes of matching (which must always
look at the mask), serialization to netlink can be problematic. Since
the flow and the mask are serialized separately, the uninitialized
portions of the flow can be encoded with whatever values happen to be
present.
In terms of functionality, this has little effect since these fields
will be masked out by definition. However, it leaks kernel memory to
userspace, which is a potential security vulnerability. It is also
possible that other code paths could look at the masked key and get
uninitialized data, although this does not currently appear to be an
issue in practice.
This removes the mask optimization for flows that are being installed.
This was always intended to be the case as the mask optimizations were
really targetting per-packet flow operations.
Fixes: 03f0d916 ("openvswitch: Mega flow implementation")
Signed-off-by: Jesse Gross <jesse@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 54d792f257 ("net: dsa: Centralise global and port setup
code into mv88e6xxx.") merged in the 4.2 merge window broke the link
speed forcing for the CPU port of Marvell DSA switches. The original
code was:
/* MAC Forcing register: don't force link, speed, duplex
* or flow control state to any particular values on physical
* ports, but force the CPU port and all DSA ports to 1000 Mb/s
* full duplex.
*/
if (dsa_is_cpu_port(ds, p) || ds->dsa_port_mask & (1 << p))
REG_WRITE(addr, 0x01, 0x003e);
else
REG_WRITE(addr, 0x01, 0x0003);
but the new code does a read-modify-write:
reg = _mv88e6xxx_reg_read(ds, REG_PORT(port), PORT_PCS_CTRL);
if (dsa_is_cpu_port(ds, port) ||
ds->dsa_port_mask & (1 << port)) {
reg |= PORT_PCS_CTRL_FORCE_LINK |
PORT_PCS_CTRL_LINK_UP |
PORT_PCS_CTRL_DUPLEX_FULL |
PORT_PCS_CTRL_FORCE_DUPLEX;
if (mv88e6xxx_6065_family(ds))
reg |= PORT_PCS_CTRL_100;
else
reg |= PORT_PCS_CTRL_1000;
The link speed in the PCS control register is a two bit field. Forcing
the link speed in this way doesn't ensure that the bit field is set to
the correct value - on the hardware I have here, the speed bitfield
remains set to 0x03, resulting in the speed not being forced to gigabit.
We must clear both bits before forcing the link speed.
Fixes: 54d792f257 ("net: dsa: Centralise global and port setup code into mv88e6xxx.")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Partially due to a pre-exising "thinko", the new metadata-based tx/rx
paths were handling ECN propagation differently than the traditional
tx/rx paths. This patch removes the "thinko" (involving multiple
ip_hdr assignments) on the rx path and corrects the ECN handling on
both the rx and tx paths.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The order of the following three spinlocks should be:
dlm_domain_lock < dlm_ctxt->spinlock < dlm_lock_resource->spinlock
But dlm_dispatch_assert_master() is called while holding
dlm_ctxt->spinlock and dlm_lock_resource->spinlock, and then it calls
dlm_grab() which will take dlm_domain_lock.
Once another thread (for example, dlm_query_join_handler) has already
taken dlm_domain_lock, and tries to take dlm_ctxt->spinlock deadlock
happens.
Signed-off-by: Joseph Qi <joseph.qi@huawei.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: "Junxiao Bi" <junxiao.bi@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We don't need to specify an explicit rule in the Makefile, the implicit
one will do the same. The "__EXPORTED_HEADERS__" define is not needed,
because we build the test against the installed kernel headers, not the
in-tree kernel headers. Re-use "$(TEST_PROGS)" in the clean target
rather than spelling the executable name twice. Include <unistd.h>
rather than the rather specific <asm-generic/unistd.h>. Include
<syscall.h> rather than <sys/syscall.h>. In both cases, the former
header is located in a standard location and includes the latter.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Pranith Kumar <bobby.prani@gmail.com>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The sane_reclaim() helper is supposed to return false for memcg reclaim
if the legacy hierarchy is used, because the latter lacks dirty
throttling mechanism, and so it did before it was accidentally broken by
commit 33398cf2f3 ("memcg: export struct mem_cgroup"). Fix it.
Fixes: 33398cf2f3 ("memcg: export struct mem_cgroup")
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The check for invoking iommu->lazy_flush() from iommu_tbl_range_alloc()
has to be refactored so that we only call ->lazy_flush() if it is
non-null.
I had a sparc kernel that was crashing when I was trying to process some
very large perf.data files- the crash happens when the scsi driver calls
into dma_4v_map_sg and thus the iommu_tbl_range_alloc().
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In not-instrumented code KASAN replaces instrumented memset/memcpy/memmove
with not-instrumented analogues __memset/__memcpy/__memove.
However, on x86 the EFI stub is not linked with the kernel. It uses
not-instrumented mem*() functions from arch/x86/boot/compressed/string.c
So we don't replace them with __mem*() variants in EFI stub.
On ARM64 the EFI stub is linked with the kernel, so we should replace
mem*() functions with __mem*(), because the EFI stub runs before KASAN
sets up early shadow.
So let's move these #undef mem* into arch's asm/efi.h which is also
included by the EFI stub.
Also, this will fix the warning in 32-bit build reported by kbuild test
robot:
efi-stub-helper.c:599:2: warning: implicit declaration of function 'memcpy'
[akpm@linux-foundation.org: use 80 cols in comment]
Signed-off-by: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Reported-by: Fengguang Wu <fengguang.wu@gmail.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit bcc5422230 ("mm: hugetlb: introduce page_huge_active")
each hugetlb page maintains its active flag to avoid a race condition
betwe= en multiple calls of isolate_huge_page(), but current kernel
doesn't set the f= lag on a hugepage allocated by migration because the
proper putback routine isn= 't called. This means that users could
still encounter the race referred to by bcc5422230 in this special
case, so this patch fixes it.
Fixes: bcc5422230 ("mm: hugetlb: introduce page_huge_active")
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: <stable@vger.kernel.org> [4.1.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For VM_PFNMAP and VM_MIXEDMAP we use vm_ops->pfn_mkwrite instead of
vm_ops->page_mkwrite to notify abort write access. This means we want
vma->vm_page_prot to be write-protected if the VMA provides this vm_ops.
A theoretical scenario that will cause these missed events is:
On writable mapping with vm_ops->pfn_mkwrite, but without
vm_ops->page_mkwrite: read fault followed by write access to the pfn.
Writable pte will be set up on read fault and write fault will not be
generated.
I found it examining Dave's complaint on generic/080:
http://lkml.kernel.org/g/20150831233803.GO3902@dastard
Although I don't think it's the reason.
It shouldn't be a problem for ext2/ext4 as they provide both pfn_mkwrite
and page_mkwrite.
[akpm@linux-foundation.org: add local vm_ops to avoid 80-cols mess]
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Yigal Korman <yigal@plexistor.com>
Acked-by: Boaz Harrosh <boaz@plexistor.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Dave Chinner <david@fromorbit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the userfaultfd syscalls to uapi asm-generic, it was tested with
postcopy live migration on aarch64 with both 4k and 64k pagesize
kernels.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On ppc big endian this check fails, the mutex doesn't necessarily need
to be identical for all pages after pthread_mutex_lock/unlock cycles.
The count verification (outside of the pthread_mutex_t structure)
suffices and that is retained.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This will report the error in the exit code, in addition of the fprintf.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Keep a non-zero placeholder after the count, for the my_bcmp comparison
of the page against the zeropage. The lockless increment between 255 to
256 against a lockless my_bcmp could otherwise return false positives on
ppc32le.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Tested-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If __NR_userfaultfd is not yet defined by the arch, warn but still build
and run the userfaultfd selftest successfully.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Depend on "make headers_install" to create proper headers to include and
provide syscall numbers.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the usr/include subdirectory of the top-level tree to the include
path, and make sure to include headers without relative paths to make
sure the sanitized headers get picked up. Otherwise the compiler will
not be able to find the linux/compiler.h header included by the non-
sanitized include/uapi/linux/userfaultfd.h.
While at it, make sure to only hardcode the syscall numbers on x86 and
PowerPC if they haven't been properly picked up from the headers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 51360155ec and adapts
fs/userfaultfd.c to use the old version of that function.
It didn't look robust to call __wake_up_common with "nr == 1" when we
absolutely require wakeall semantics, but we've full control of what we
insert in the two waitqueue heads of the blocked userfaults. No
exclusive waitqueue risks to be inserted into those two waitqueue heads
so we can as well stick to "nr == 1" of the old code and we can rely
purely on the fact no waitqueue inserted in one of the two waitqueue
heads we must enforce as wakeall, has wait->flags WQ_FLAG_EXCLUSIVE set.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
c770cb4cb5 ("PCI: Mark invalid BARs as unassigned") sets IORESOURCE_UNSET
if we fail to claim a resource. If we tried to claim a bridge window,
failed, clipped the window, and tried to claim the clipped window, we
failed again because of IORESOURCE_UNSET:
pci_bus 0000:00: root bus resource [mem 0xc0000000-0xffffffff window]
pci 0000:00:01.0: can't claim BAR 15 [mem 0xbdf00000-0xddefffff 64bit pref]: no compatible bridge window
pci 0000:00:01.0: [mem size 0x20000000 64bit pref] clipped to [mem size 0x1df00000 64bit pref]
pci 0000:00:01.0: bridge window [mem size 0x1df00000 64bit pref]
pci 0000:00:01.0: can't claim BAR 15 [mem size 0x1df00000 64bit pref]: no address assigned
The 00:01.0 window started as [mem 0xbdf00000-0xddefffff 64bit pref]. That
starts before the host bridge window [mem 0xc0000000-0xffffffff window], so
we clipped the 00:01.0 window to [mem 0xc0000000-0xddefffff 64bit pref].
But we left it marked IORESOURCE_UNSET, so the second claim failed when it
should have succeeded.
This means downstream devices will also fail for lack of resources, e.g.,
in the bugzilla below,
radeon 0000:01:00.0: Fatal error during GPU init
Clear IORESOURCE_UNSET when we clip a bridge window. Also clear
IORESOURCE_UNSET in our copy of the unclipped window so we can see exactly
what the original window was and how it now fits inside the upstream
window.
Fixes: c770cb4cb5 ("PCI: Mark invalid BARs as unassigned")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491#c47
Based-on-patch-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Based-on-patch-by: Yinghai Lu <yinghai@kernel.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
CC: stable@vger.kernel.org # v4.1+
PCM receive and transmit DMA requestor lines were reverted, breaking the
PCM playback interface for PXA platforms using the sound/soc/ variant
instead of the sound/arm variant.
The commit below shows the inversion in the requestor lines.
Fixes: d65a14587a ("ASoC: pxa: use snd_dmaengine_dai_dma_data")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The NMI entry code that switches to the normal kernel stack needs to
be very careful not to clobber any extra stack slots on the NMI
stack. The code is fine under the assumption that SWAPGS is just a
normal instruction, but that assumption isn't really true. Use
SWAPGS_UNSAFE_STACK instead.
This is part of a fix for some random crashes that Sasha saw.
Fixes: 9b6e6a8334 ("x86/nmi/64: Switch stacks on userspace NMI entry")
Reported-and-tested-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/974bc40edffdb5c2950a5c4977f821a446b76178.1442791737.git.luto@kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
PARAVIRT_ADJUST_EXCEPTION_FRAME generates this code (using nmi as an
example, trimmed for readability):
ff 15 00 00 00 00 callq *0x0(%rip) # 2796 <nmi+0x6>
2792: R_X86_64_PC32 pv_irq_ops+0x2c
That's a call through a function pointer to regular C function that
does nothing on native boots, but that function isn't protected
against kprobes, isn't marked notrace, and is certainly not
guaranteed to preserve any registers if the compiler is feeling
perverse. This is bad news for a CLBR_NONE operation.
Of course, if everything works correctly, once paravirt ops are
patched, it gets nopped out, but what if we hit this code before
paravirt ops are patched in? This can potentially cause breakage
that is very difficult to debug.
A more subtle failure is possible here, too: if _paravirt_nop uses
the stack at all (even just to push RBP), it will overwrite the "NMI
executing" variable if it's called in the NMI prologue.
The Xen case, perhaps surprisingly, is fine, because it's already
written in asm.
Fix all of the cases that default to paravirt_nop (including
adjust_exception_frame) with a big hammer: replace paravirt_nop with
an asm function that is just a ret instruction.
The Xen case may have other problems, so document them.
This is part of a fix for some random crashes that Sasha saw.
Reported-and-tested-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/8f5d2ba295f9d73751c33d97fda03e0495d9ade0.1442791737.git.luto@kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Linux cifs mount with ntlmssp against an Mac OS X (Yosemite
10.10.5) share fails in case the clocks differ more than +/-2h:
digest-service: digest-request: od failed with 2 proto=ntlmv2
digest-service: digest-request: kdc failed with -1561745592 proto=ntlmv2
Fix this by (re-)using the given server timestamp for the
ntlmv2 authentication (as Windows 7 does).
A related problem was also reported earlier by Namjae Jaen (see below):
Windows machine has extended security feature which refuse to allow
authentication when there is time difference between server time and
client time when ntlmv2 negotiation is used. This problem is prevalent
in embedded enviornment where system time is set to default 1970.
Modern servers send the server timestamp in the TargetInfo Av_Pair
structure in the challenge message [see MS-NLMP 2.2.2.1]
In [MS-NLMP 3.1.5.1.2] it is explicitly mentioned that the client must
use the server provided timestamp if present OR current time if it is
not
Reported-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Steve French <smfrench@gmail.com>
CC: Stable <stable@vger.kernel.org>
leases (oplocks) were always requested for SMB2/SMB3 even when oplocks
disabled in the cifs.ko module.
Signed-off-by: Steve French <steve.french@primarydata.com>
Reviewed-by: Chandrika Srinivasan <chandrika.srinivasan@citrix.com>
CC: Stable <stable@vger.kernel.org>
When dropping a snapshot we need to account for the qgroup changes. If we drop
the snapshot in all one go then the backref code will fail to find blocks from
the snapshot we dropped since it won't be able to find the root in the fs root
cache. This can lead to us failing to find refs from other roots that pointed
at blocks in the now deleted root. To handle this we need to not remove the fs
roots from the cache until after we process the qgroup operations. Do this by
adding dropped roots to a list on the transaction, and letting the transaction
remove the roots at the same time it drops the commit roots. This will keep all
of the backref searching code in sync properly, and fixes a problem Mark was
seeing with snapshot delete and qgroups. Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com>
Tested-by: Holger Hoffstätte <holger.hoffstaette@googlemail.com>
Signed-off-by: Chris Mason <clm@fb.com>
Support for Wolfson Microelectronics devices is now part of Cirrus Logic
and the relevant parts of the old opensource.wolfsonmicro.com site have
moved to the Cirrus Logic GitHub area.
This patch updates the website and git repo links, and also removes an
obsolete website link for the voltage and current drivers.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
XTFPGA SPI controller has native endian registers.
Fix register acessors so that they work in big-endian configurations.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The split of the 8250 driver into a 8250_base/8250.ko resulted in a
lack of a license for the 8250_base.ko module. This caused the module
to fail to load and the kernel to be tainted. Add the appropriate
MODULE_LICENSE to 8250_port.c, which is always compiled into
8250_base.ko
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reported-by: Mikael Pettersson <mikpelinux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patches fix the following one issue:
- Fix bug of the is_extcon_changed() which check whether specific cable is
attached or detached.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pCg7
-----END PGP SIGNATURE-----
Merge tag 'extcon-fixes-for-4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into char-misc-linus
Chanwoo writes:
Update extcon for v4.3-rc3
This patches fix the following one issue:
- Fix bug of the is_extcon_changed() which check whether specific cable is
attached or detached.
When masking/unmasking interrupts, mask_cache is updated and used later
for suspend/resume. Unfortunately, it always was the mask_cache
associated with the first irq chip which was updated. So when performing
resume, only irqs 0-31 could be enabled.
Fixes: b1479ebb77 ("irqchip: atmel-aic: Add atmel AIC/AIC5 drivers")
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: <sasha.levin@oracle.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <nicolas.ferre@atmel.com>
Cc: <alexandre.belloni@free-electrons.com>
Cc: <boris.brezillon@free-electrons.com>
Cc: <Wenyou.Yang@atmel.com>
Cc: <jason@lakedaemon.net>
Cc: <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org #3.18
Link: http://lkml.kernel.org/r/1442843173-2390-1-git-send-email-ludovic.desroches@atmel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The current behavior of notifying CQM events is inconsistent:
Upon first configuration there is a cqm event with the current
status according to threshold configured, regardless of signal
stability.
When there is reconfiguration no event is sent unless there is
a significant change to the signal level according to the new
configuration.
Since the current reconfiguration behavior might cause missing
CQM events in case the current signal did not change but is on
the other side of the new threshold, fix that by resetting the
stored signal level upon reconfiguration.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The HT MCS mask has 9 bytes, the VHT one only has 8 streams.
Split the loops to handle this correctly.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Don't check if timer is running with a timer_pending() before
deleting it with del_timer_sync(), this defies the whole point of
the sync part and can cause a possible race.
Instead we just want to make sure the timer is initialized early enough
before we have a chance to delete it.
Cc: <stable@vger.kernel.org>
Reported-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some changes between xhci 0.96 and xhci 1.0 specifications forced us to
check the hci version in code, some of these checks were implemented as
hci_version == 1.0, which will not work with new xhci 1.1 controllers.
xhci 1.1 behaves similar to xhci 1.0 in these cases, so change these
checks to hci_version >= 1.0
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_stop will be called twice, once for the shared hcd
and again for the primary hcd.
We stop the XHCI controller in any case so clean up
everything on the first call else we can timeout
waiting for pending requests to complete.
Cc: <stable@vger.kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For whatever reason if XHCI died in the previous instant
then it will never recover on the next xhci_start unless we
clear the DYING flag.
Cc: <stable@vger.kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_pme_quirk() is only used when CONFIG_PM is defined.
Compiling a kernel without PM complains about this function
[reworded commit message -Mathias]
Cc: <stable@vger.kernel.org>
Signed-off-by: Tomer Barletz <barletz@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want to give the command abortion an additional try to stop
the command ring before we completely hose xhci.
Cc: <stable@vger.kernel.org>
Tested-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bits 1:0 of the bmAttributes are used for the burst multiplier.
The rest of the bits used to be reserved (zero), but USB3.1 takes bit 7
into use.
Use the existing USB_SS_MULT() macro instead to make sure the mult value
and hence max packet calculations are correct for USB3.1 devices.
Note that burst multiplier in bmAttributes is zero based and that
the USB_SS_MULT() macro adds one.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the second pull request for current -rc cycle.
A few fixes on dummy_hcd which have been around for
longer than they should be.
MUSB got a couple fixes, the most important of which
is a fix to DMA channel teardown on AM335x devices.
And DWC3 got a minor fix for when using RT-enabled
kernels.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Lyn+
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.3-rc3
Here's the second pull request for current -rc cycle.
A few fixes on dummy_hcd which have been around for
longer than they should be.
MUSB got a couple fixes, the most important of which
is a fix to DMA channel teardown on AM335x devices.
And DWC3 got a minor fix for when using RT-enabled
kernels.
Neil Armstrong