Following the correct power up sequence:
dp_pd=ff => dp_pd=7f => wait 10us => dp_pd=00
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-7-enric.balletbo@collabora.com
When we enable bridge failed, we have to retry it, otherwise we would get
the abnormal display.
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-5-enric.balletbo@collabora.com
We should check AUX_EN bit to confirm the AUX CH operation is completed.
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-3-enric.balletbo@collabora.com
We currently wait for the panel to mirror our intended PSR state
before continuing on both PSR enter and PSR exit. This is really
only important to do when we're entering PSR, since we want to
be sure the last frame we pushed is being served from the panel's
internal fb before shutting down the soc blocks (vop/analogix).
This patch changes the behavior such that we only wait for the
panel to complete the PSR transition when we're entering PSR, and
to skip verification when we're exiting.
Cc: Stéphane Marchesin <marcheu@chromium.org>
Cc: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180309222327.18689-7-enric.balletbo@collabora.com
Make sure the request PSR state takes effect in analogix_dp_send_psr_spd()
function, or print the sink PSR error state if we failed to apply the
requested PSR setting.
Cc: 征增 王 <wzz@rock-chips.com>
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
[seanpaul changed timeout loop to a readx poll]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180309222327.18689-2-enric.balletbo@collabora.com
Reference from drm_dp_aux description (about transfer):
Upon success, the implementation should return the number of payload bytes
that were transferred, or a negative error-code on failure. Helpers
propagate errors from the .transfer() function, with the exception of
the -EBUSY error, which causes a transaction to be retried. On a short,
helpers will return -EPROTO to make it simpler to check for failure.
The analogix_dp_transfer will return num_transferred, but if there is none
byte been transferred, the return value will be 0, which means success, we
should return error-code if transfer none byte.
for (retry = 0; retry < 32; retry++) {
err = aux->transfer(aux, &msg);
if (err < 0) {
if (err == -EBUSY)
continue;
goto unlock;
}
}
Cc: zain wang <wzz@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1479255219-7243-1-git-send-email-jay.xu@rock-chips.com
Remove code for reading the EDID and DPCD fields and use the helpers
instead.
Besides the obvious code reduction, other helpers are being added to the
core that could be used in this driver and will be good to be able to
use them instead of duplicating them.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Yakir Yang <ykk@rock-chips.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Archit Taneja <architt@codeaurora.org>
The full name of PSR is Panel Self Refresh, panel device could refresh
itself with the hardware framebuffer in panel, this would make lots of
sense to save the power consumption.
This patch have exported two symbols for platform driver to implement
the PSR function in hardware side:
- analogix_dp_active_psr()
- analogix_dp_inactive_psr()
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
As vendor document indicate, when REF_CLK bit set 0, then DP
phy's REF_CLK should switch to 24M source clock.
But due to IC PHY layout mistaken, some chips need to flip this
bit(like RK3288), and unfortunately they didn't indicate in the
DP version register. That's why we have to make this little hack.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Tomasz Figa <tomasz.figa@chromium.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
It may caused a dead lock if we flush the hpd work in bridge disable time.
The normal flow would like:
IN --> DRM IOCTL
1. Acquire crtc_ww_class_mutex (DRM IOCTL)
IN --> analogix_dp_bridge
2. Acquire hpd work lock (Flush hpd work)
3. HPD work already in idle, no need to run the work function.
OUT <-- analogix_dp_bridge
OUT <-- DRM IOCTL
The dead lock flow would like:
IN --> DRM IOCTL
1. Acquire crtc_ww_class_mutex (DRM IOCTL)
IN --> analogix_dp_bridge
2. Acquire hpd work lock (Flush hpd work)
IN --> analogix_dp_hotplug
IN --> drm_helper_hpd_irq_event
3. Acquire mode_config lock (This lock already have been acquired in previous step 1)
** Dead Lock Now **
It's wrong to flush the hpd work in bridge->disable time, I guess the
original code just want to ensure the delay work must be finish before
encoder disabled.
The flush work in bridge disable time is try to ensure the HPD event
won't be missed before display card disabled, actually we can take a
fast respond way(interrupt thread) to update DRM HPD event to fix the
delay update and possible dead lock.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Some edp screen do not have hpd signal, so we can't just return
failed when hpd plug in detect failed.
This is an hardware property, so we need add a devicetree property
"analogix,need-force-hpd" to indicate this sutiation.
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
RK3288 need some special registers setting, we can separate
them out by the dev_type of plat_data.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Both hsync/vsync polarity and interlace mode can be parsed from
drm display mode, and dynamic_range and ycbcr_coeff can be judge
by the video code.
But presumably Exynos still relies on the DT properties, so take
good use of mode_fixup() in to achieve the compatibility hacks.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
link_rate and lane_count already configured in analogix_dp_set_link_train(),
so we don't need to config those repeatly after training finished, just
remove them out.
Beside Display Port 1.2 already support 5.4Gbps link rate, the maximum sets
would change from {1.62Gbps, 2.7Gbps} to {1.62Gbps, 2.7Gbps, 5.4Gbps}.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Fix some obvious alignment problems, like alignment and line
over 80 characters problems, make this easy to be maintained
later.
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
In the original split we kept the register constants intact to keep the
diff small. Still the constants are Analogix-specific, so rename them now.
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Split the dp core driver from exynos directory to bridge directory,
and rename the core driver to analogix_dp_*, rename the platform
code to exynos_dp.
Beside the new analogix_dp driver would export six hooks.
"analogix_dp_bind()" and "analogix_dp_unbind()"
"analogix_dp_suspned()" and "analogix_dp_resume()"
"analogix_dp_detect()" and "analogix_dp_get_modes()"
The bind/unbind symbols is used for analogix platform driver to connect
with analogix_dp core driver. And the detect/get_modes is used for analogix
platform driver to init the connector.
They reason why connector need register in helper driver is rockchip drm
haven't implement the atomic API, but Exynos drm have implement it, so
there would need two different connector helper functions, that's why we
leave the connector register in helper driver.
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
zain wang