Commit Graph

1302 Commits

Author SHA1 Message Date
Felipe Balbi fbea935acc usb: dwc3: gadget: rename dwc3_endpoint_transfer_complete()
Now that we're making sure we don't have XferComplete events, we can
rename this function to what it actually handles:
dwc3_gadget_endpoint_transfer_in_progress()

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-05-21 10:00:49 +03:00
Felipe Balbi 742a4fff5f usb: dwc3: gadget: XferComplete only for EP0
XferComplete is enabled only for the default control pipe, let's make
that clear in the code.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-05-21 10:00:48 +03:00
Felipe Balbi 38408464aa usb: dwc3: gadget: XferNotReady is Isoc-only
We don't use XferNotReady for anything other than Default Control
Pipe, which is handled in ep0.c, and Isochronous endpoints. Let's make
that clear in the code.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-05-21 10:00:48 +03:00
Felipe Balbi 52fcc0bead usb: dwc3: gadget: pre-issue Start Transfer for Interrupt EPs too
Interrupt endpoints behave much like Bulk endpoints with the exception
that they are periodic. We can pre-issue Start Transfer exactly as we
do for Bulk endpoints.

While at that, remove one trailing blank line which is unnecessary.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-05-21 10:00:48 +03:00
Anurag Kumar Vulisha c96e6725db usb: dwc3: gadget: Correct the logic for queuing sgs
The present code correctly fetches the req which were previously not
queued from the started_list but fails to continue queuing from the sg
where it previously stopped queuing (because of the unavailable TRB's).
This patch correct's the code to continue queuing from the correct sg
present in the sglist.

For example, consider 5 sgs in req. Because of limited TRB's among the
5 sgs only 3 got queued. This patch corrects the code to start queuing
from correct sg i.e 4th sg when the TRBs are available.

Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-05-21 10:00:47 +03:00
Anurag Kumar Vulisha a31e63b608 usb: dwc3: gadget: Correct handling of scattergather lists
The code logic in dwc3_prepare_one_trb() incorrectly uses the address
and length fields present in req packet for mapping TRB's instead of
using the address and length fields of scattergather lists. This patch
correct's the code to use sg->address and sg->length when scattergather
lists are present.

Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-05-21 10:00:47 +03:00
Andrzej Hajda 5f0b74e548 USB: dwc3: get extcon device by OF graph bindings
extcon device is used to detect host/device connection. Since extcon
OF property is deprecated, alternative method should be added.
This method uses OF graph bindings to locate extcon.

Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-05-16 08:56:16 +03:00
Masahiro Yamada fe8abf332b usb: dwc3: support clocks and resets for DWC3 core
Historically, the clocks and resets are handled on the glue layer
side instead of the DWC3 core.  For simple cases, dwc3-of-simple.c
takes care of arbitrary number of clocks and resets.  The DT node
structure typically looks like as follows:

  dwc3-glue {
          compatible = "foo,dwc3";
          clocks = ...;
          resets = ...;
          ...

          dwc3 {
                  compatible = "snps,dwc3";
                  ...
          };
  }

By supporting the clocks and the reset in the dwc3/core.c, it will
be turned into a single node:

  dwc3 {
          compatible = "foo,dwc3", "snps,dwc3";
          clocks = ...;
          resets = ...;
          ...
  }

This commit adds the binding of clocks and resets specific to this IP.
The number of clocks should generally be the same across SoCs, it is
just some SoCs either tie clocks together or do not provide software
control of some of the clocks.

I took the clock names from the Synopsys datasheet: "ref" (ref_clk),
"bus_early" (bus_clk_early), and "suspend" (suspend_clk).

I found only one reset line in the datasheet, hence the reset-names
property is omitted.

Those clocks are required for new platforms.  Enforcing the new
binding breaks existing platforms since they specify clocks (and
resets) in their glue layer node, but nothing in the core node.
I listed such exceptional cases in the DT binding.  The driver
code has been relaxed to accept no clock.  This change is based
on the discussion [1].

I inserted reset_control_deassert() and clk_bulk_enable() before the
first register access, i.e. dwc3_cache_hwparams().

[1] https://patchwork.kernel.org/patch/10284265/

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-05-16 08:52:39 +03:00
Masahiro Yamada 44feb8e6ea usb: dwc3: use local copy of resource to fix-up register offset
It is not a good idea to directly modify the resource of a platform
device.  Modify its local copy, and pass it to devm_ioremap_resource()
so that we do not need to restore it in the failure path and the remove
hook.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-05-15 10:23:47 +03:00
Manu Gautam bcb128777a usb: dwc3: core: Suspend PHYs on runtime suspend in host mode
Some PHY drivers (e.g. for Qualcomm QUSB2 and QMP PHYs) support
runtime PM to reduce PHY power consumption during bus_suspend.
Add changes to let core auto-suspend PHYs on host bus-suspend
using GUSB2PHYCFG register if needed for a platform. Also perform
PHYs runtime suspend/resume and let platform glue drivers e.g.
dwc3-qcom handle remote wakeup during bus suspend by waking up
devices on receiving wakeup event from PHY.

Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-05-15 10:20:32 +03:00
Manu Gautam a4333c3a6b usb: dwc3: Add Qualcomm DWC3 glue driver
DWC3 controller on Qualcomm SOCs has a Qscratch wrapper.
Some of its uses are described below resulting in need to
have a separate glue driver instead of using dwc3-of-simple:
 - It exposes register interface to override vbus-override
   and lane0-pwr-present signals going to hardware. These
   must be updated in peripheral mode for DWC3 if vbus lines
   are not connected to hardware block. Otherwise RX termination
   in SS mode or DP pull-up is not applied by device controller.
 - pwr_events_irq_stat support to check if USB2 PHY is in L2 state
   before glue driver proceeds with suspend.
 - Support for wakeup interrupts lines that are asserted whenever
   there is any wakeup event on USB3 or USB2 bus.
 - Support to replace pip3 clock going to DWC3 with utmi clock
   for hardware configuration where SSPHY is not used with DWC3.

Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-05-15 10:20:13 +03:00
Icenowy Zheng e362098f0e usb: dwc3: of-simple: Add compatible for Allwinner H6 platform
Add compatible string to use this generic glue layer to support
Allwinner H6 platform's dwc3 controller.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-05-15 10:18:35 +03:00
Felipe Balbi c91815b596 usb: dwc3: gadget: never call ->complete() from ->ep_queue()
This is a requirement which has always existed but, somehow, wasn't
reflected in the documentation and problems weren't found until now
when Tuba Yavuz found a possible deadlock happening between dwc3 and
f_hid. She described the situation as follows:

spin_lock_irqsave(&hidg->write_spinlock, flags); // first acquire
/* we our function has been disabled by host */
if (!hidg->req) {
	free_ep_req(hidg->in_ep, hidg->req);
	goto try_again;
}

[...]

status = usb_ep_queue(hidg->in_ep, hidg->req, GFP_ATOMIC);
=>
	[...]
	=> usb_gadget_giveback_request
		=>
		f_hidg_req_complete
			=>
			spin_lock_irqsave(&hidg->write_spinlock, flags); // second acquire

Note that this happens because dwc3 would call ->complete() on a
failed usb_ep_queue() due to failed Start Transfer command. This is,
anyway, a theoretical situation because dwc3 currently uses "No
Response Update Transfer" command for Bulk and Interrupt endpoints.

It's still good to make this case impossible to happen even if the "No
Reponse Update Transfer" command is changed.

Reported-by: Tuba Yavuz <tuba@ece.ufl.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2018-03-26 13:22:09 +02:00
Greg Kroah-Hartman 6d23ee9caa usb: changes for v4.17 merge window
Quite a lot happened in this cycle, with a total of 95 non-merge
 commits. The most interesting parts are listed below:
 
 Synopsys has been adding better support for USB 3.1 to dwc3. The same
 series also sets g_mass_storage's max speed to SSP.
 
 Roger Quadros (TI) added support for dual-role using the OTG block
 available in some dwc3 implementations, this makes sure that AM437x
 can swap roles in runtime.
 
 We have a new SoC supported in dwc3 now - Amlogic Meson GX - thanks to
 the work of Martin Blumenstingl.
 
 We also have a ton of changes in dwc2 (51% of all changes, in
 fact). The most interesting part there is the support for
 Hibernation (a Synopsys PM feature).
 
 Apart from these, we have our regular set of non-critical fixes all
 over the place.
 -----BEGIN PGP SIGNATURE-----
 
 iQJRBAABCgA7FiEElLzh7wn96CXwjh2IzL64meEamQYFAlq03lYdHGZlbGlwZS5i
 YWxiaUBsaW51eC5pbnRlbC5jb20ACgkQzL64meEamQYfDg/+KAupmSBOJDXKIMD6
 MZiIVLhSkBYFM5vwIs2+SwLl4H9wXmvoxqvcZaBH2qk5zWy0wdwnTLLCSDt/dCCy
 Rhrz//KFZStmPP1chJg8fU0yV4Wy4NIif3paTy4P2hEdPcn1XrDoekP+DhLKg6dz
 RbFRxEHnOhGvB4Wo2Rd/H1E6Pi6Vdd7iMCQdoDpatdrsIrplXZ8qnUOvIBY2Xi1K
 LEj7d+SAAEmwGm4QyzDzItR4wqKqhrcQ7Xlvi7pW/22AlJfMD82+Gr0JAnKCeshX
 3+ksnAbDz3p5AXJm5I+T3c4Zyd3BPyZevc72jTFkf0ggwNjMOtUuxTQhCRQSRRwA
 +gofFEvJ/vrWQWZzVhvzZQmTrc8sP2vUaAoGpfIBMBEVqxP89BfMgvf3wU9/if37
 WvICdpZ0o0pOGUkLduhyDIm0/SEBEIAqSY/uU1m5LsZzboR7B3Gm6IWsHhHSMZz8
 Dd8aljQxR1fNnHoqUlc2yu1IiI9PQCNJcY6Waah3CKMgp0EH1KbK00E34oxUQUwF
 Edl6jsOrkv4L4X8BonKuipezwl1TTXjiAK1fE3N8SkorcndIww35kVVLKqFrCQOf
 5VBuGYTgGNCubb2wk8wx/TSBXsM/zpQ6y0uPKg/1icpMmXqFrrv2emyTKa2YS7y8
 KPqBQmz6Cj9g8Sn4OcffWACMiHU=
 =F6OC
 -----END PGP SIGNATURE-----

Merge tag 'usb-for-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing

Felipe writes:

usb: changes for v4.17 merge window

Quite a lot happened in this cycle, with a total of 95 non-merge
commits. The most interesting parts are listed below:

Synopsys has been adding better support for USB 3.1 to dwc3. The same
series also sets g_mass_storage's max speed to SSP.

Roger Quadros (TI) added support for dual-role using the OTG block
available in some dwc3 implementations, this makes sure that AM437x
can swap roles in runtime.

We have a new SoC supported in dwc3 now - Amlogic Meson GX - thanks to
the work of Martin Blumenstingl.

We also have a ton of changes in dwc2 (51% of all changes, in
fact). The most interesting part there is the support for
Hibernation (a Synopsys PM feature).

Apart from these, we have our regular set of non-critical fixes all
over the place.
2018-03-23 13:33:09 +01:00
Roger Quadros 7d11c3ac66 usb: dwc3: core: Fix broken system suspend/resume on AM437x
On TI's AM437x, the DWC3 controller looses state after a
system suspend/resume. We are re-initializing the controller
but we miss restoring the PRTCAP register. This causes
USB host to break on AM437x after a system suspend/resume.

Fix this by restoring the PRTCAP register on system resume.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-22 10:50:15 +02:00
Thinh Nguyen 2f3090c6a8 usb: dwc3: Check controller type before setting speed
DWC_usb3 speed can only be set up to SuperSpeed. Limit the setting to
SuperSpeed only should the value be higher. Otherwise, the controller
will read an invalid speed value and set the device to an incorrect
speed.

Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-22 10:49:03 +02:00
Thinh Nguyen 80b776340c usb: dwc3: Dump LSP and BMU debug info
Dump LSP and BMU debug info.

Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-22 10:49:02 +02:00
Thinh Nguyen 938a5ad1d3 usb: dwc3: Check for ESS TX/RX threshold config
Check and configure TX/RX threshold for DWC_usb31. Update dwc3 structure
with new fields to store these threshold configurations.

Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-22 10:48:59 +02:00
Thinh Nguyen 6743e817a4 usb: dwc3: Add DWC_usb31 GTXTHRCFG reg fields
Add new GTXTHRCFG bit field macros for DWC_usb31. The GTXTHRCFG register
fields for DWC_usb31 is as follows:
 +-------+--------------------------+-----------------------------------+
 | BITS  | Name                     | Description                       |
 +=======+==========================+===================================+
 | 31:27 | reserved                 |                                   |
 | 26    | UsbTxPktCntSel           | Async ESS transmit packet         |
 |       |                          | threshold enable                  |
 | 25:21 | UsbTxPktCnt              | Async ESS transmit packet         |
 |       |                          | threshold count                   |
 | 20:16 | UsbMaxTxBurstSize        | Async ESS Max transmit burst size |
 | 15    | UsbTxThrNumPktSel_HS_Prd | HS high bandwidth periodic        |
 |       |                          | transmit packet threshold enable  |
 | 14:13 | UsbTxThrNumPkt_HS_Prd    | HS high bandwidth periodic        |
 |       |                          | transmit packet threshold count   |
 | 12:11 | reserved                 |                                   |
 | 10    | UsbTxThrNumPktSel_Prd    | Periodic ESS transmit packet      |
 |       |                          | threshold enable                  |
 | 9:5   | UsbTxThrNumPkt_Prd       | Periodic ESS transmit packet      |
 |       |                          | threshold count                   |
 | 4:0   | UsbMaxTxBurstSize_Prd    | Max periodic ESS TX burst size    |
 +-------+--------------------------+-----------------------------------+

Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-22 10:48:55 +02:00
Thinh Nguyen 01b0e2cc7d usb: dwc3: gadget: Check IP revision for GRXTHRCFG
DWC_usb31 controller has a different UsbRxPktCnt bit fields from
GRXTHRCFG register. Check for DWC_usb31 IP revision to read the
appropriate value.

Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-22 10:48:53 +02:00
Thinh Nguyen 2fbc5bdc8f usb: dwc3: Add DWC_usb31 GRXTHRCFG bit fields
Add new GRXTHRCFG bit field macros for DWC_usb31. The GRXTHRCFG register
fields for DWC_usb31 is as follows:
 +-------+--------------------------+----------------------------------+
 | BITS  | Name                     | Description                      |
 +=======+==========================+==================================+
 | 31:27 | reserved                 |                                  |
 | 26    | UsbRxPktCntSel           | Async ESS receive packet         |
 |       |                          | threshold enable                 |
 | 25:21 | UsbRxPktCnt              | Async ESS receive packet         |
 |       |                          | threshold count                  |
 | 20:16 | UsbMaxRxBurstSize        | Async ESS Max receive burst size |
 | 15    | UsbRxThrNumPktSel_HS_Prd | HS high bandwidth periodic       |
 |       |                          | receive packet threshold enable  |
 | 14:13 | UsbRxThrNumPkt_HS_Prd    | HS high bandwidth periodic       |
 |       |                          | receive packet threshold count   |
 | 12:11 | reserved                 |                                  |
 | 10    | UsbRxThrNumPktSel_Prd    | Periodic ESS receive packet      |
 |       |                          | threshold enable                 |
 | 9:5   | UsbRxThrNumPkt_Prd       | Periodic ESS receive packet      |
 |       |                          | threshold count                  |
 | 4:0   | UsbMaxRxBurstSize_Prd    | Max periodic ESS RX burst size   |
 +-------+--------------------------+----------------------------------+

Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-22 10:48:51 +02:00
Thinh Nguyen d548a61767 usb: dwc3: Check IP revision for GTXFIFOSIZ
DWC_usb31 controller has different GTXFIFOSIZE bit field for TXFDEF.
Check for DWC_usb31 IP revision to read the appropriate bit fields.

Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-22 10:48:50 +02:00
Thinh Nguyen 0cab8d26d6 usb: dwc3: Update DWC_usb31 GTXFIFOSIZ reg fields
Update two GTXFIFOSIZ bit fields for the DWC_usb31 controller. TXFDEP
is a 15-bit value instead of 16-bit value, and bit 15 is TXFRAMNUM.

The GTXFIFOSIZ register for DWC_usb31 is as follows:
 +-------+-----------+----------------------------------+
 | BITS  | Name      | Description                      |
 +=======+===========+==================================+
 | 31:16 | TXFSTADDR | Transmit FIFOn RAM Start Address |
 | 15    | TXFRAMNUM | Asynchronous/Periodic TXFIFO     |
 | 14:0  | TXFDEP    | TXFIFO Depth                     |
 +-------+-----------+----------------------------------+

Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-22 10:48:48 +02:00
Thinh Nguyen fab3833338 usb: dwc3: Add SoftReset PHY synchonization delay
From DWC_usb31 programming guide section 1.3.2, once DWC3_DCTL_CSFTRST
bit is cleared, we must wait at least 50ms before accessing the PHY
domain (synchronization delay).

Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-22 10:48:46 +02:00
Thinh Nguyen cabdf83dad usb: dwc3: pci: Properly cleanup resource
Platform device is allocated before adding resources. Make sure to
properly cleanup on error case.

Cc: <stable@vger.kernel.org>
Fixes: f1c7e71081 ("usb: dwc3: convert to pcim_enable_device()")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-22 10:48:18 +02:00
Felipe Balbi de948a74ad usb: dwc3: Makefile: fix link error on randconfig
If building a kernel without FTRACE but with TRACING, dwc3.ko fails to
link due to missing trace events. Fix this by using the correct
Kconfig symbol on Makefile.

Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-22 10:45:20 +02:00
Heinrich Schuchardt 7642d8386a usb: dwc3: ep0: remove redundant assignment
In

	dwc3_request	*r = NULL;
	r = A;

the first assignment has no effect. Remove it.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-19 10:52:12 +02:00
Roger Quadros 498f0478ab usb: dwc3: Prevent indefinite sleep in _dwc3_set_mode during suspend/resume
In the following test we get stuck by sleeping forever in _dwc3_set_mode()
after which dual-role switching doesn't work.

On dra7-evm's dual-role port,
- Load g_zero gadget driver and enumerate to host
- suspend to mem
- disconnect USB cable to host and connect otg cable with Pen drive in it.
- resume system
- we sleep indefinitely in _dwc3_set_mode due to.
  dwc3_gadget_exit()->usb_del_gadget_udc()->udc_stop()->
	dwc3_gadget_stop()->wait_event_lock_irq()

To fix this instead of waiting indefinitely with wait_event_lock_irq()
we use wait_event_interruptible_lock_irq_timeout() and print
and error message if there was a timeout.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-13 10:47:59 +02:00
Roger Quadros f09cc79b4b usb: dwc3: add dual role support using OTG block
This is useful on platforms (e.g. TI AM437x) that don't
have ID available on a GPIO but do have the OTG block.

We can obtain the ID state via the OTG block and use it
for dual-role switching.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-13 10:47:52 +02:00
Roger Quadros daaecc6541 usb: dwc3: prevent setting PRTCAP to OTG from debugfs
We don't support PRTCAP == OTG yet, so prevent user from
setting it via debugfs.

Fixes: 41ce1456e1 ("usb: dwc3: core: make dwc3_set_mode() work properly")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-13 10:47:51 +02:00
Roger Quadros 4cff75c7fe usb: dwc3: core.h: add some register definitions
Add OTG and GHWPARAMS6 register definitions

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-13 10:47:51 +02:00
Martin Blumenstingl e8284db48f usb: dwc3: of-simple: add support for the Amlogic Meson GXL and AXG SoCs
Amlogic Meson GXL and AXG SoCs come with a (host-only) dwc3 USB
controller. To use this controller a clock has to be enabled and a reset
line has to be pulsed.
Enabling the clock works identical to other SoCs. However, the reset
line has to be pulsed (using reset_control_reset) instead of using a
level reset (reset_control_{assert,deassert}).

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-13 10:47:50 +02:00
Martin Blumenstingl ff0a632f08 usb: dwc3: of-simple: add support for shared and pulsed reset lines
Some SoCs (such as Amlogic Meson GXL for example) share the reset line
with other components (in case of the Meson GXL example there's a shared
reset line between the USB2 PHYs, USB3 PHYs and the dwc3 controller).
Additionally SoC implementations may prefer a reset pulse over level
resets.

For now this falls back to the old defaults, which are:
- reset lines are exclusive
- level resets are being used

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-13 10:47:50 +02:00
Felipe Balbi 6d5b53c1fd usb: dwc3: debugfs: Re-use DEFINE_SHOW_ATTRIBUTE() macro
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.

Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-03-08 15:12:00 +02:00
Roger Quadros 084a804e01 usb: dwc3: Fix lock-up on ID change during system suspend/resume
To reproduce the lock up do the following
- connect otg host adapter and a USB device to the dual-role port
so that it is in host mode.
- suspend to mem.
- disconnect otg adapter.
- resume the system.

If we call dwc3_host_exit() before tasks are thawed
xhci_plat_remove() seems to lock up at the second usb_remove_hcd() call.

To work around this we queue the _dwc3_set_mode() work on
the system_freezable_wq.

Fixes: 41ce1456e1 ("usb: dwc3: core: make dwc3_set_mode() work properly")
Cc: <stable@vger.kernel.org> # v4.12+
Suggested-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-02-28 09:57:04 +02:00
Roger Quadros 98112041bc usb: dwc3: core: Fix ULPI PHYs and prevent phy_get/ulpi_init during suspend/resume
In order for ULPI PHYs to work, dwc3_phy_setup() and dwc3_ulpi_init()
must be doene before dwc3_core_get_phy().

commit 541768b08a ("usb: dwc3: core: Call dwc3_core_get_phy() before initializing phys")
broke this.

The other issue is that dwc3_core_get_phy() and dwc3_ulpi_init() should
be called only once during the life cycle of the driver. However,
as dwc3_core_init() is called during system suspend/resume it will
result in multiple calls to dwc3_core_get_phy() and dwc3_ulpi_init()
which is wrong.

Fix this by moving dwc3_ulpi_init() out of dwc3_phy_setup()
into dwc3_core_ulpi_init(). Use a flag 'ulpi_ready' to ensure that
dwc3_core_ulpi_init() is called only once from dwc3_core_init().

Use another flag 'phys_ready' to call dwc3_core_get_phy() only once from
dwc3_core_init().

Fixes: 541768b08a ("usb: dwc3: core: Call dwc3_core_get_phy() before initializing phys")
Fixes: f54edb539c ("usb: dwc3: core: initialize ULPI before trying to get the PHY")
Cc: linux-stable <stable@vger.kernel.org> # >= v4.13
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-02-15 15:28:35 +02:00
Thinh Nguyen b16ea8b949 usb: dwc3: Fix GDBGFIFOSPACE_TYPE values
The FIFO/Queue type values are incorrect. Correct them according to
DWC_usb3 programming guide section 1.2.27 (or DWC_usb31 section 1.2.25).

Additionally, this patch includes ProtocolStatusQ and AuxEventQ types.

Fixes: cf6d867d3b ("usb: dwc3: core: add fifo space helper")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-02-12 10:55:51 +02:00
Roger Quadros c49f63055e usb: dwc3: omap: don't miss events during suspend/resume
The USB cable state can change during suspend/resume
so be sure to check and update the extcon state.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-02-12 10:53:18 +02:00
Manu Gautam c4a5153e87 usb: dwc3: core: Power-off core/PHYs on system_suspend in host mode
Commit 689bf72c6e ("usb: dwc3: Don't reinitialize core during
host bus-suspend/resume") updated suspend/resume routines to not
power_off and reinit PHYs/core for host mode.
It broke platforms that rely on DWC3 core to power_off PHYs to
enter low power state on system suspend.

Perform dwc3_core_exit/init only during host mode system_suspend/
resume to addresses power regression from above mentioned patch
and also allow USB session to stay connected across
runtime_suspend/resume in host mode. While at it also replace
existing checks for HOST only dr_mode with current_dr_role to
have similar core driver behavior for both Host-only and DRD+Host
configurations.

Fixes: 689bf72c6e ("usb: dwc3: Don't reinitialize core during host bus-suspend/resume")
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-02-12 10:50:16 +02:00
Brian Norris 00b42170c8 usb: dwc3: Undo PHY init if soft reset fails
In this function, we init the USB2 and USB3 PHYs, but if soft reset
times out, we don't unwind this.

Noticed by inspection.

Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-02-12 10:49:49 +02:00
Thinh Nguyen f035d139ff usb: dwc3: ep0: Reset TRB counter for ep0 IN
DWC3 tracks TRB counter for each ep0 direction separately. In control
read transfer completion handler, the driver needs to reset the TRB
enqueue counter for ep0 IN direction. Currently the driver only resets
the TRB counter for control OUT endpoint. Check for the data direction
and properly reset the TRB counter from correct control endpoint.

Cc: stable@vger.kernel.org
Fixes: c2da2ff006 ("usb: dwc3: ep0: don't use ep0in for transfers")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-02-12 10:48:39 +02:00
Thinh Nguyen 6180026341 usb: dwc3: gadget: Set maxpacket size for ep0 IN
There are 2 control endpoint structures for DWC3. However, the driver
only updates the OUT direction control endpoint structure during
ConnectDone event. DWC3 driver needs to update the endpoint max packet
size for control IN endpoint as well. If the max packet size is not
properly set, then the driver will incorrectly calculate the data
transfer size and fail to send ZLP for HS/FS 3-stage control read
transfer.

The fix is simply to update the max packet size for the ep0 IN direction
during ConnectDone event.

Cc: stable@vger.kernel.org
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-02-12 10:48:36 +02:00
Enric Balletbo i Serra bff52352e0 usb: dwc3: of-simple: fix oops by unbalanced clk disable call
dwc3_of_simple_dev_pm_ops has never been used since commit a0d8c4cfdf
("usb: dwc3: of-simple: set dev_pm_ops"), but this commit has brought
and oops when unbind the device due this sequence:

  dwc3_of_simple_remove
   -> clk_disable ...
      -> pm_runtime_put_sync
         -> dwc3_of_simple_runtime_suspend
            -> clk_disable (again)

This double call to clk_core_disable causes a kernel oops like this:

 WARNING: CPU: 1 PID: 4022 at drivers/clk/clk.c:656 clk_core_disable+0x78/0x80
 CPU: 1 PID: 4022 Comm: bash Not tainted 4.15.0-rc4+ #44
 Hardware name: Google Kevin (DT)
 pstate: 80000085 (Nzcv daIf -PAN -UAO)
 pc : clk_core_disable+0x78/0x80
 lr : clk_core_disable_lock+0x20/0x38
 sp : ffff00000bbf3a90
 ...
 Call trace:
  clk_core_disable+0x78/0x80
  clk_disable+0x1c/0x30
  dwc3_of_simple_runtime_suspend+0x30/0x50
  pm_generic_runtime_suspend+0x28/0x40

This patch fixes the unbalanced clk disable call by setting the num_clocks
variable to zero once the clocks were disabled.

Fixes: a0d8c4cfdf ("usb: dwc3: of-simple: set dev_pm_ops")
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-02-12 10:41:45 +02:00
Greg Kroah-Hartman f1faf88c13 phy: for 4.16
*) Fix in exynos5-usbdrd to enumerate SuperSpeed devices on Odroid XU3
  *) Fix in Broadcom USB PHY to get Dell Low Speed keyboards working
  *) Fix in Broadcom USB PHY to power down the PHY when XHCI disabled
     to save power
  *) Fix in Broadcom USB PHY to prevent abort in DRD mode
  *) Fix in Broadcom USB PHY to use the correct dt properties
  *) Fix in Mediatek PHY to detect device connection
  *) Make getting resource optional for Mediatek V1 TPHY
  *) Cleanup in Mediatek PHY
 
 Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.11 (GNU/Linux)
 
 iQIcBAABAgAGBQJaSzimAAoJEA5ceFyATYLZrCUP/3f02fVtkF+OAL3e+ZwgCWy/
 xoGIHffTcrYFimPeHh7INbeA16o2qNcN8JxJqQFFpZtZIoBR60az6ql7P2CZomXv
 Z4S8ftKl8cOEI6O6AmLgRFuxaHSG24IxD54rHwCa6bDAoq36VnHM2CG+EEB6Yd3M
 4eYoS1hQuwFCKeWSmHo4Uq8zyvTwIaxfKhOBlonXZu3/Tt34ZR0sGr3FC2OIamTN
 Isrx/BsdHsfg+mTElos9jnc5/Uhwy/r7JFmRotn06cWGw2EGoM6EOXBrp3WXHD/f
 jQnSSP3ZKmDvq0zY7QywXVo+fVWddZYx3fsbd26A5bUsarcj2VWlbHWyAWtYty3N
 HOuucYbMHSXTFxP/0j6pwONzQIIucisGgNdUc4Zc7nzwcF8A/BWrEMkGqZLit45q
 NalvVz/+lk0be3zZngm/vbaztHbHMQDvKe0U5QbHH9h47MybmydocrPgs7JbDcFd
 P0vHJ1be5CMItcElC0w+fkrRf3tk5IYQb4nZFDaTRSiuLU+S+mgLfYjbGH4lXtnQ
 USsGRv827wFqQVEzay2WvazvviBautoneh2+YDMg7R1cSOh9kQkunPl9ePOig/DR
 Cgy1MEZH8GZIIhIOBshnLQ2FiQbtnn0NkDTOajLNyJssFbE+9XXYKJr/cUvCOArP
 W9GjMMvI06gI7T+sDylY
 =f9so
 -----END PGP SIGNATURE-----

Merge tag 'phy-for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next

Kishon writes:

phy: for 4.16

 *) Fix in exynos5-usbdrd to enumerate SuperSpeed devices on Odroid XU3
 *) Fix in Broadcom USB PHY to get Dell Low Speed keyboards working
 *) Fix in Broadcom USB PHY to power down the PHY when XHCI disabled
    to save power
 *) Fix in Broadcom USB PHY to prevent abort in DRD mode
 *) Fix in Broadcom USB PHY to use the correct dt properties
 *) Fix in Mediatek PHY to detect device connection
 *) Make getting resource optional for Mediatek V1 TPHY
 *) Cleanup in Mediatek PHY

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2018-01-08 14:17:59 +01:00
Greg Kroah-Hartman 958e052c54 usb: changes for v4.16 merge window
Not many changes here, the most important being an improvement for TI's
 AM57xx and DRA7xx devices which allows them to disable a metastability
 workaround in situations where we know what's going on.
 
 Other than that, we have a set of changes on Renesas UDC to make the
 code a little easier to read and maintain while also better supporting
 extcon framework.
 
 The u_serial adaptation layer learned to use kfifo instead of cooking
 its own FIFO implementation.
 
 DWC3 learned to decode a few more USB requests on the trace output.
 -----BEGIN PGP SIGNATURE-----
 
 iQJQBAABCgA7FiEElLzh7wn96CXwjh2IzL64meEamQYFAlpTWGYdHGZlbGlwZS5i
 YWxiaUBsaW51eC5pbnRlbC5jb20ACgkQzL64meEamQYDsw/4jOBzuVM2A28oCDzd
 H9RCagGp4dXpdvLRpueE+L16AA/5MrAI1H1Tdp063Xr+CmlPeMf98JRI5tfBpfn5
 8bE6yTojMfvb7vL82kjrnKwKh59IvKVLlFftPBIGJp1uKl5KwWUWMWRcvnpVJHdY
 SlZ0U79Pje7RBuq0BkBQ9Lm47pPm5sMqzCyyte4wZbR+6GkAA5W0PBuRes0JLBHo
 gUb9h5ns5afrxEdvzUXKpVpd++oP/ZLoZ++jYJ10Z5qSC8+y0DiwRxq7OdOSil+c
 BEMKe7I46tGzDFZ2wuMQByHWqCXp7o+9VSf5BYxyP1L58qH1N7M7GyH0Oe+r5xAi
 tjFrnL0C8Ax+ouaXLBfmFzv/52BjEqGoqtscWZ4XyVqq98NC1bP5b+qVmIkzXkdv
 P7T2lOFZX0ILDX7QXIQbXv71UA/m3bwi3IG0eNX5Rik5xQjDVHnLDpuj87wW1wSH
 aUg7sHpggn6GdOICHw9Zry3Z07u3Rab8ThuH0Z4oBI2+3EGhbXTHDjpKYwFYCWEw
 nI+9XloOdEkOE6P3S2VO1cQ7YkJ+r4/YRDRvPq3XfLETfxPHwIjqiVeSQWaBA2U8
 Om4f/1Oe83jtpfl1T7zL2z08TVPDNMOpE2j4FThA682Pa15emqymRXGDgDmFVizO
 boMiMHcP8Wp0MMegK/3RL4syrg==
 =uwh/
 -----END PGP SIGNATURE-----

Merge tag 'usb-for-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next

Felipe writes:

usb: changes for v4.16 merge window

Not many changes here, the most important being an improvement for TI's
AM57xx and DRA7xx devices which allows them to disable a metastability
workaround in situations where we know what's going on.

Other than that, we have a set of changes on Renesas UDC to make the
code a little easier to read and maintain while also better supporting
extcon framework.

The u_serial adaptation layer learned to use kfifo instead of cooking
its own FIFO implementation.

DWC3 learned to decode a few more USB requests on the trace output.
2018-01-08 14:03:30 +01:00
Vivek Gautam d8c80bb3b5 phy: exynos5-usbdrd: Calibrate LOS levels for exynos5420/5800
Adding phy calibration sequence for USB 3.0 DRD PHY present on
Exynos5420/5800 systems.
This calibration facilitates setting certain PHY parameters viz.
the Loss-of-Signal (LOS) Detector Threshold Level, as well as
Tx-Vboost-Level for Super-Speed operations.
Additionally we also set proper time to wait for RxDetect measurement,
for desired PHY reference clock, so as to solve issue with enumeration
of few USB 3.0 devices, like Samsung SUM-TSB16S 3.0 USB drive
on the controller.

We are using CR_port for this purpose to send required data
to override the LOS values.

On testing with USB 3.0 devices on USB 3.0 port present on
SMDK5420, and peach-pit boards should see following message:
usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd

and without this patch, should see below shown message:
usb 1-1: new high-speed USB device number 2 using xhci-hcd

[Also removed unnecessary extra lines in the register macro definitions]

Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
[adapted to use phy_calibrate as entry point]
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
2017-12-29 13:00:35 +05:30
Roger Quadros 42bf02ec6e usb: dwc3: Allow disabling of metastability workaround
Some platforms (e.g. TI's DRA7 USB2 instance) have more trouble
with the metastability workaround as it supports only
a High-Speed PHY and the PHY can enter into an Erratic state [1]
when the controller is set in SuperSpeed mode as part of
the metastability workaround.

This causes upto 2 seconds delay in enumeration on DRA7's USB2
instance in gadget mode.

If these platforms can be better off without the workaround,
provide a device tree property to suggest that so the workaround
is avoided.

[1] Device mode enumeration trace showing PHY Erratic Error.
     irq/90-dwc3-969   [000] d...    52.323145: dwc3_event: event (00000901): Erratic Error [U0]
     irq/90-dwc3-969   [000] d...    52.560646: dwc3_event: event (00000901): Erratic Error [U0]
     irq/90-dwc3-969   [000] d...    52.798144: dwc3_event: event (00000901): Erratic Error [U0]

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-12-11 12:36:53 +02:00
Vincent Pelletier 204ec1af62 usb: dwc3: Make sparse a bit happier
Fixes the following warnings:
drivers/usb/dwc3/io.h:43:31: warning: incorrect type in argument 1 (different address spaces)
drivers/usb/dwc3/io.h:43:31:    expected void *base
drivers/usb/dwc3/io.h:43:31:    got void [noderef] <asn:2>*
drivers/usb/dwc3/io.h:62:32: warning: incorrect type in argument 1 (different address spaces)
drivers/usb/dwc3/io.h:62:32:    expected void *base
drivers/usb/dwc3/io.h:62:32:    got void [noderef] <asn:2>*

This fixes the noisiest ones as they get emitted multiple times.
A few warnings remain, for which the proper fix is less clear.

No behaviour change is expected.

Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-12-11 12:36:49 +02:00
Felipe Balbi 19e0b203bf usb: dwc3: ep0: use gadget->isoch_delay for isoch_delay value
Instead of keeping our own isoch_delay, let's make use of the newly
introduced isoch_delay member in struct usb_gadget. The benefit here
is that we would be using a generic "API" which other UDCs can use,
resulting in a common setup for gadget drivers who may be interested
in Isoch Delay value.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-12-11 12:36:49 +02:00
Felipe Balbi 0c5d2954f6 usb: dwc3: debug: decode a few more features
We were missing U1, U2 and LTM Enable features. Let's decode them.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-12-11 12:36:48 +02:00
Manu Gautam ec5bb87e4e usb: dwc3: gadget: Fix PCM1 for ISOC EP with ep->mult less than 3
For isochronous endpoints with ep->mult less than 3, PCM1 value of
trb->size in set incorrectly.
For ep->mult = 2, this is set to 0/-1 and for ep->mult = 1, this is
set to -2. This is because the initial mult is set to ep->mult - 1
instead of 2.

Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-12-11 12:35:37 +02:00
Masahiro Yamada a0d8c4cfdf usb: dwc3: of-simple: set dev_pm_ops
dwc3_of_simple_dev_pm_ops has never been used since the initial support
by commit 16adc674d0 ("usb: dwc3: add generic OF glue layer").

I guess it just missed to set .pm struct member.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-12-11 12:35:36 +02:00
Andreas Platschek ded600ea9f usb: dwc3: of-simple: fix missing clk_disable_unprepare
If of_clk_get() fails, the clean-up of already initialized clocks should be
the same as when clk_prepare_enable() fails. Thus a clk_disable_unprepare()
for each clock should be called before the clk_put().

Found by Linux Driver Verification project (linuxtesting.org).

Fixes: 16adc674d0 ("usb: dwc3: ep0: fix setup_packet_pending initialization")

Signed-off-by: Andreas Platschek <andreas.platschek@opentech.at>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-12-11 12:35:36 +02:00
Vincent Pelletier 8722e095f5 usb: dwc3: gadget: Wait longer for controller to end command processing
DWC3_DEPCMD_ENDTRANSFER has been witnessed to require around 600 iterations
before controller would become idle again after unplugging the USB cable
with AIO reads submitted.
Bump timeout from 500 iterations to 1000 so dwc3_stop_active_transfer does
not receive -ETIMEDOUT and does not WARN:

[   81.326273] ------------[ cut here ]------------
[   81.335341] WARNING: CPU: 0 PID: 1874 at drivers/usb/dwc3/gadget.c:2627 dwc3_stop_active_transfer.constprop.23+0x69/0xc0 [dwc3]
[   81.347094] Modules linked in: usb_f_fs libcomposite configfs bnep btsdio bluetooth ecdh_generic brcmfmac brcmutil dwc3 intel_powerclamp coretemp ulpi kvm_intel udc_core kvm irqbypass crc32_pclmul crc32c_intel pcbc dwc3_pci aesni_intel aes_i586 crypto_simd cryptd ehci_pci ehci_hcd basincove_gpadc industrialio gpio_keys usbcore usb_common
[   81.378142] CPU: 0 PID: 1874 Comm: irq/34-dwc3 Not tainted 4.14.0-edison+ #119
[   81.385545] Hardware name: Intel Corporation Merrifield/BODEGA BAY, BIOS 542 2015.01.21:18.19.48
[   81.394548] task: f5b1be00 task.stack: f420a000
[   81.399219] EIP: dwc3_stop_active_transfer.constprop.23+0x69/0xc0 [dwc3]
[   81.406086] EFLAGS: 00010086 CPU: 0
[   81.409672] EAX: 0000001f EBX: f5729800 ECX: c132a2a2 EDX: 00000000
[   81.416096] ESI: f4054014 EDI: f41cf400 EBP: f420be10 ESP: f420bdf4
[   81.422521]  DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
[   81.428061] CR0: 80050033 CR2: b7a3f000 CR3: 01d94000 CR4: 001006d0
[   81.434483] Call Trace:
[   81.437063]  __dwc3_gadget_ep_disable+0xa3/0x2b0 [dwc3]
[   81.442438]  ? _raw_spin_lock_irqsave+0x32/0x40
[   81.447135]  dwc3_gadget_ep_disable+0xbf/0xe0 [dwc3]
[   81.452269]  usb_ep_disable+0x1c/0xd0 [udc_core]
[   81.457048]  ffs_func_eps_disable.isra.15+0x3b/0x90 [usb_f_fs]
[   81.463070]  ffs_func_set_alt+0x7d/0x310 [usb_f_fs]
[   81.468132]  ffs_func_disable+0x14/0x20 [usb_f_fs]
[   81.473075]  reset_config+0x5b/0x90 [libcomposite]
[   81.478023]  composite_disconnect+0x2b/0x50 [libcomposite]
[   81.483685]  dwc3_disconnect_gadget+0x39/0x50 [dwc3]
[   81.488808]  dwc3_gadget_disconnect_interrupt+0x21b/0x250 [dwc3]
[   81.495014]  dwc3_thread_interrupt+0x2a8/0xf70 [dwc3]
[   81.500219]  ? __schedule+0x78c/0x7e0
[   81.504027]  irq_thread_fn+0x18/0x30
[   81.507715]  ? irq_thread+0xb7/0x180
[   81.511400]  irq_thread+0x111/0x180
[   81.515000]  ? irq_finalize_oneshot+0xe0/0xe0
[   81.519490]  ? wake_threads_waitq+0x30/0x30
[   81.523806]  kthread+0x107/0x110
[   81.527131]  ? disable_percpu_irq+0x50/0x50
[   81.531439]  ? kthread_stop+0x150/0x150
[   81.535397]  ret_from_fork+0x19/0x24
[   81.539136] Code: 89 d8 c7 45 ec 00 00 00 00 c7 45 f0 00 00 00 00 c7 45 f4 00 00 00 00 e8 56 ef ff ff 85 c0 74 12 50 68 b9 1c 14 f8 e8 64 0f f7 c8 <0f> ff 58 5a 8d 76 00 8b 83 98 00 00 00 c6 83 a0 00 00 00 00 83
[   81.559295] ---[ end trace f3133eec81a473b8 ]---

Number of iterations measured on 4 consecutive unplugs:
[ 1088.799777] dwc3_send_gadget_ep_cmd(cmd=331016, params={0, 0, 0}) iterated 605 times
[ 1222.024986] dwc3_send_gadget_ep_cmd(cmd=331016, params={0, 0, 0}) iterated 580 times
[ 1317.590452] dwc3_send_gadget_ep_cmd(cmd=331016, params={0, 0, 0}) iterated 598 times
[ 1453.218314] dwc3_send_gadget_ep_cmd(cmd=331016, params={0, 0, 0}) iterated 594 times

Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-12-11 12:35:36 +02:00
Linus Torvalds 894025f24b USB/PHY patches for 4.15-rc1
Here is the big set of USB and PHY driver updates for 4.15-rc1.
 
 There is the usual amount of gadget and xhci driver updates, along with
 phy and chipidea enhancements.  There's also a lot of SPDX tags and
 license boilerplate cleanups as well, which provide some churn in the
 diffstat.
 
 Other major thing is the typec code that moved out of staging and into
 the "real" part of the drivers/usb/ tree, which was nice to see happen.
 
 All of these have been in linux-next with no reported issues for a
 while.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgm/Vw8cZ3JlZ0Brcm9h
 aC5jb20ACgkQMUfUDdst+yktXwCdGgpInfOEvOGFd83EPDL7a1ncyc4AoM5wI8yl
 1CeLipqVIN3IsMMJptvb
 =zvDI
 -----END PGP SIGNATURE-----

Merge tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB/PHY updates from Greg KH:
 "Here is the big set of USB and PHY driver updates for 4.15-rc1.

  There is the usual amount of gadget and xhci driver updates, along
  with phy and chipidea enhancements. There's also a lot of SPDX tags
  and license boilerplate cleanups as well, which provide some churn in
  the diffstat.

  Other major thing is the typec code that moved out of staging and into
  the "real" part of the drivers/usb/ tree, which was nice to see
  happen.

  All of these have been in linux-next with no reported issues for a
  while"

* tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
  usb: gadget: f_fs: Fix use-after-free in ffs_free_inst
  USB: usbfs: compute urb->actual_length for isochronous
  usb: core: message: remember to reset 'ret' to 0 when necessary
  USB: typec: Remove remaining redundant license text
  USB: typec: add SPDX identifiers to some files
  USB: renesas_usbhs: rcar?.h: add SPDX tags
  USB: chipidea: ci_hdrc_tegra.c: add SPDX line
  USB: host: xhci-debugfs: add SPDX lines
  USB: add SPDX identifiers to all remaining Makefiles
  usb: host: isp1362-hcd: remove a couple of redundant assignments
  USB: adutux: remove redundant variable minor
  usb: core: add a new usb_get_ptm_status() helper
  usb: core: add a 'type' parameter to usb_get_status()
  usb: core: introduce a new usb_get_std_status() helper
  usb: core: rename usb_get_status() 'type' argument to 'recip'
  usb: core: add Status Type definitions
  USB: gadget: Remove redundant license text
  USB: gadget: function: Remove redundant license text
  USB: gadget: udc: Remove redundant license text
  USB: gadget: legacy: Remove redundant license text
  ...
2017-11-13 21:14:07 -08:00
Greg Kroah-Hartman b5ea47570b USB: dwc3: Remove redundant license text
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner.  So the extra GPL text wording
can be removed as it is no longer needed at all.

This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text.  And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.

No copyright headers or other non-license-description text was removed.

Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-07 15:45:01 +01:00
Greg Kroah-Hartman 5fd54ace47 USB: add SPDX identifiers to all remaining files in drivers/usb/
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.

Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.

This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.

Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-04 11:48:02 +01:00
Greg Kroah-Hartman b24413180f License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-02 11:10:55 +01:00
Manu Gautam 644cbbc3ab usb: dwc3: core: Notify current USB mode to USB3 PHY as well
Driver currently notifies only USB2 PHY on USB mode change.
Extend this to USB3 PHY so that PHY drivers based on the
mode can release system resources - clocks, regulators etc.
Additionally Qualcomm QMP and QUSB2 PHY drivers need to
override VBUS signal in PHY wrapper in device mode as USB
VBUS line is not connected to PHYs. Also, remove NULL checks
for PHY when calling phy_set_mode as PHY ops already check this.

Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-10-24 12:51:20 +03:00
Manu Gautam 8eed00b237 usb: dwc3: pci: Runtime resume child device from wq
Driver currently resumes and increments pm usage_count
of its child device (dwc3 main) from its runtime_resume
handler. This requires dwc3 runtime_resume to perform
pm_runtime_put to decrement the pm usage_count. However
runtime_put from dwc3 happens for non pci drivers
(e.g. dwc3-if-simple.c) as well which results in dwc3
pm usage_count becoming negative after couple of
runtime suspend resume iterations. Fix this by
performing runtime_get/put from dwc3-pci driver only
using workqueue.

Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-10-24 12:51:19 +03:00
Manu Gautam 689bf72c6e usb: dwc3: Don't reinitialize core during host bus-suspend/resume
Driver powers-off PHYs and reinitializes DWC3 core and gadget on
resume. While this works fine for gadget mode but in host
mode there is not re-initialization of host stack. Also, resetting
bus as part of bus_suspend/resume is not correct which could affect
(or disconnect) connected devices.
Fix this by not reinitializing core on suspend/resume in host mode
for HOST only and OTG/drd configurations.

Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-10-24 12:51:19 +03:00
Vivek Gautam 06c47e6286 usb: dwc3: of-simple: Add support to get resets for the device
Add support to get a list of resets available for the device.
These resets must be kept de-asserted until the device is
in use.

Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
[p.zabel@pengutronix.de: switch to hidden reset control array]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-10-19 15:23:14 +03:00
Vivek Gautam d6d9c2a3ea usb: dwc3: of-simple: Re-order resource handling in remove
Move clock handling after of_platform_depopulate to achieve
a sequence that is reverse of the probe sequence.

Cc: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-10-19 12:36:53 +03:00
Christos Gkekas 86763723ee usb: dwc3: ep0: Clean up unused variables
Many variables in ep0 are set but never used, so should be removed.

Signed-off-by: Christos Gkekas <chris.gekas@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-10-19 10:38:10 +03:00
Felipe Balbi 7fdca76649 usb: dwc3: gadget: simplify __dwc3_gadget_kick_transfer() prototype
Now that all the information we need sits in struct dwc3_ep, we can
start taking only a pointer to struct dwc3_ep as an argument. This
allows us to clean the code up a bit.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-10-19 10:38:06 +03:00
Felipe Balbi 502a37b98a usb: dwc3: gadget: cache frame number in struct dwc3_ep
This is in preparation to simplifying prototype of
__dwc3_gadget_kick_transfer().

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-10-19 10:38:05 +03:00
Felipe Balbi 64e0108029 usb: dwc3: gadget: simplify __dwc3_gadget_ep_queue()
There is more possibility for sharing code if we just realise that now
__dwc3_gadget_kic_transfer() knows to break out early if there are no
TRBs left.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-10-19 10:38:05 +03:00
Felipe Balbi ccb94ebf9e usb: dwc3: gadget: check for lack of TRBs a bit earlier
This will let us call __dwc3_gadget_kick_transfer()
unconditionally. No functional changes, cleanup only.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-10-19 10:38:05 +03:00
Baolin Wang c3cdce45f8 usb: dwc3: of-simple: Add compatible for Spreadtrum SC9860 platform
Add compatible string to use this generic glue layer to support
Spreadtrum SC9860 platform's dwc3 controller.

Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-09-28 12:41:56 +03:00
Felipe Balbi 5516847083 usb: dwc3: ep0: fix DMA starvation by assigning req->trb on ep0
If we don't assign a TRB to ep0 requests, we won't be able to unmap
the request later on resulting in starvation of DMA resources.

Fixes: 4a71fcb8ac ("usb: dwc3: gadget: only unmap requests from DMA if mapped")
Reported-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Tested-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-09-18 13:30:30 +03:00
Greg Kroah-Hartman 34a0036748 usb: changes for v4.14 merge window
Not a big pull request this time around. Only 49 non-merge
 commits. This pull request is, however, all over the place. Most of
 the changes are in the bdc driver adding support for USB Phy layer and
 PM.
 
 Renesas adds support for R-Car H3 ES2.0 and R-Car M3-W SoCs.
 
 Also here is PM_RUNTIME support for dwc3-keystone.
 
 UDC Core got a DMA unmap fix to make sure we only unmap requests that
 were, indeed, mapped.
 
 Other than these, we have a lot of cleanups, many of them adding
 'const' to several places.
 -----BEGIN PGP SIGNATURE-----
 
 iQJRBAABCAA7FiEElLzh7wn96CXwjh2IzL64meEamQYFAlmaxjsdHGZlbGlwZS5i
 YWxiaUBsaW51eC5pbnRlbC5jb20ACgkQzL64meEamQZOXRAAlxA/jU0DVtZ8YAAC
 6GRVni3xiEkoEoGA8tQwPZVZh0QRlupKtq5E31xWxjW2Hmtd/159WlIWZcFo3Cgi
 ChDZ7yBQ0NGJhOS8X1zYSM6Rl9DDzKtk1vh7EXhz1CjG3aYTqwELLy9ZvCJUTG4w
 O57XNH8GtRptmloOrFT+LvI6lb2EpcxGSTMhf0kUdnAC3Iw6gBL8PGr+jnoTLQ4M
 gcddC5oQ24CpPFB/mszGd3Ro2USiNipttJmZJ/yrYLGcBIoIL4oyNbbAkhvcXAai
 4cBsC7SELifgTJZ2npoUh0z+tRsmQ668zqXS81QgS8/Y6uFgmp4PWoTiGCLbpEm0
 l/T5jMDeHFySmBM8+0opbXjXzK2FVG+NnGNkRPxpwoue6cUlay2dw2PGVhP0/6Y9
 DQfv3bOHsEEe2ywp3J7UAZPFw4UaLKM8yWJ/Tv0DUhDolG8bA2PerU5vX5W6FufY
 tWkvpTjRWKBVgHfYIUJoYtxLMsEubHQeuuc/hKEU+uqJ3161IQyUbOx547Y7toVi
 E2mdDfN+Zv/PW5lNJ+GguK3eTxeJ8w4aBKC6VY+mLoATEDa5xzq9OzGJ118LcV3V
 f4Nw7UsqinJYxCJMKgZHHCnrd6ct0wmhcsiWq9J0fSRPSzwzY3IrdbkWj24Gcc8V
 Z5/lfdjee2Jx1TrUI3Lasew0qP4=
 =FSil
 -----END PGP SIGNATURE-----

Merge tag 'usb-for-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next

Felipe writes:

usb: changes for v4.14 merge window

Not a big pull request this time around. Only 49 non-merge
commits. This pull request is, however, all over the place. Most of
the changes are in the bdc driver adding support for USB Phy layer and
PM.

Renesas adds support for R-Car H3 ES2.0 and R-Car M3-W SoCs.

Also here is PM_RUNTIME support for dwc3-keystone.

UDC Core got a DMA unmap fix to make sure we only unmap requests that
were, indeed, mapped.

Other than these, we have a lot of cleanups, many of them adding
'const' to several places.
2017-08-22 13:16:06 -07:00
Shawn Guo e7059ef82a usb: dwc3: of-simple: remove include of clk-provider.h
The header clk-provider.h is there for clock drivers (providers) to
include, not client drivers (consumers).  That said,
of_clk_get_parent_count() is a helper function for clock providers, not
a clk API for consumers.

Let's replace of_clk_get_parent_count() with of_count_phandle_with_args()
call, so that we can remove the include of clk-provider.h.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-08-15 14:18:53 +03:00
Greg Kroah-Hartman feea468014 Merge 4.13-rc5 into usb-next
This gets the USB fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-14 14:50:58 -07:00
Doug Wilson 95aa932c93 usb/dwc3:constify dev_pm_ops
dev_pm_ops is not supposed to change at runtime. Marking it
 constant.

Signed-off-by: Doug Wilson <doug.wilson@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-10 11:31:26 -07:00
Franklin S Cooper Jr c14af973ed usb: dwc3: keystone: Add PM_RUNTIME Support to DWC3 Keystone USB driver
For 66AK2Gx there is a requirement to use PM Runtime to properly manage
clocks and the power domains. Therefore, add PM runtime support. Remove
legacy clock api's calls since other users of this driver worked without
these clock apis calls.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-08-09 13:10:16 +03:00
Gustavo A. R. Silva 0ae99ecba7 usb: dwc3: omap: fix error return code in dwc3_omap_probe()
platform_get_irq() returns an error code, but the dwc3-omap driver
ignores it and always returns -EINVAL. This is not correct and,
prevents -EPROBE_DEFER from being propagated properly.

Notice that platform_get_irq() no longer returns 0 on error:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e330b9a6bb35dc7097a4f02cb1ae7b6f96df92af

Print and propagate the return value of platform_get_irq on failure.

This issue was detected with the help of Coccinelle.

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-08-09 13:10:09 +03:00
Doug Wilson 8bcd988972 usb: dwc3: pci: constify dev_pm_ops
dev_pm_ops is not supposed to change at runtime. Marking it constant.

Signed-off-by: Doug Wilson <doug.wilson@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-08-09 13:09:50 +03:00
Manu Gautam 40d829fb2e usb: dwc3: gadget: Correct ISOC DATA PIDs for short packets
The PIDs for Isochronous data transfers are incorrect
for high bandwidth IN endpoints when the request length
is less than EP wMaxPacketSize.

As per spec correct PIDs for ISOC data transfers are:

1) For request length <= maxpacket
	- DATA0,

2) For maxpacket < length <= (2 * maxpacket)
	- DATA1, DATA0

3) For (2 * maxpacket) <  length <= (3 * maxpacket)
	- DATA2, DATA1, DATA0.

But driver always sets PCM fields based on wMaxPacketSize
due to which DATA2 happens even for small requests.

Fix this by setting the PCM field of trb->size depending
on request length rather than fixing it to the value
depending on wMaxPacketSize.

Ideally it shouldn't give any issues as dwc3 will send
0-length packet for next IN token if host sends (even
after receiving a short packet). Windows seems to ignore
this but with MacOS frame loss observed when using f_uvc.

Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-08-03 12:30:51 +03:00
Jack Pham 4a71fcb8ac usb: dwc3: gadget: only unmap requests from DMA if mapped
A recent optimization was made so that a request put on the
pending_list wouldn't get mapped for DMA until just before
preparing a TRB for it. However, this poses a problem in case
the request is dequeued or the endpoint is disabled before the
mapping is done as that would lead to dwc3_gadget_giveback()
unconditionally calling usb_gadget_unmap_request_for_dev() with
an invalid request->dma handle. Depending on the platform's DMA
implementation the unmap operation could result in a panic.

Since we know a successful mapping is a prerequisite for getting
a TRB, the unmap can be conditionally called only when req->trb
is non-NULL.

Fixes: cdb55b39fa ("usb: dwc3: gadget: lazily map requests for DMA")
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-07-17 11:01:27 +03:00
Vignesh R ee249b4554 usb: dwc3: omap: remove IRQ_NOAUTOEN used with shared irq
IRQ_NOAUTOEN cannot be used with shared IRQs, since commit 04c848d398
("genirq: Warn when IRQ_NOAUTOEN is used with shared interrupts") and
kernel now throws a warn dump. But OMAP DWC3 driver uses this flag. As
per commit 12a7f17fac ("usb: dwc3: omap: fix race of pm runtime with
irq handler in probe") that introduced this flag, PM runtime can race
with IRQ handler when deferred probing happens due to extcon,
therefore IRQ_NOAUTOEN needs to be set so that irq is not enabled until
extcon is registered.

Remove setting of IRQ_NOAUTOEN and move the registration of
shared irq to a point after dwc3_omap_extcon_register() and
of_platform_populate(). This avoids possibility of probe deferring and
above said race condition.

Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-07-17 10:59:31 +03:00
Vignesh R 541768b08a usb: dwc3: core: Call dwc3_core_get_phy() before initializing phys
commit f54edb539c ("usb: dwc3: core: initialize ULPI before trying to
get the PHY") moved call to dwc3_core_get_phy() from dwc3_probe() to
dwc3_core_init() after dwc3_core_soft_reset(). But
dwc3_core_soft_reset() calls phy_init(), therefore dwc3_core_get_phy()
needs to be called before dwc3_core_soft_reset().

Fix this by moving call to dwc3_core_get_phy() before
dwc3_core_soft_reset().

This fixes the following abort seen on DRA7xx platforms
[   24.769118] usb usb2: SerialNumber: xhci-hcd.1.auto
[   24.781144] hub 2-0:1.0: USB hub found
[   24.787836] hub 2-0:1.0: 1 port detected
[   24.809939] Unhandled fault: imprecise external abort (0x1406) at 0x00000000

Reported-by: Carlos Hernandez <ceh@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-07-17 10:58:56 +03:00
Linus Torvalds 408c9861c6 Power management updates for v4.13-rc1
- Rework suspend-to-idle to allow it to take wakeup events signaled
    by the EC into account on ACPI-based platforms in order to properly
    support power button wakeup from suspend-to-idle on recent Dell
    laptops (Rafael Wysocki).
 
    That includes the core suspend-to-idle code rework, support for
    the Low Power S0 _DSM interface, and support for the ACPI INT0002
    Virtual GPIO device from Hans de Goede (required for USB keyboard
    wakeup from suspend-to-idle to work on some machines).
 
  - Stop trying to export the current CPU frequency via /proc/cpuinfo
    on x86 as that is inaccurate and confusing (Len Brown).
 
  - Rework the way in which the current CPU frequency is exported by
    the kernel (over the cpufreq sysfs interface) on x86 systems with
    the APERF and MPERF registers by always using values read from
    these registers, when available, to compute the current frequency
    regardless of which cpufreq driver is in use (Len Brown).
 
  - Rework the PCI/ACPI device wakeup infrastructure to remove the
    questionable and artificial distinction between "devices that
    can wake up the system from sleep states" and "devices that can
    generate wakeup signals in the working state" from it, which
    allows the code to be simplified quite a bit (Rafael Wysocki).
 
  - Fix the wakeup IRQ framework by making it use SRCU instead of
    RCU which doesn't allow sleeping in the read-side critical
    sections, but which in turn is expected to be allowed by the
    IRQ bus locking infrastructure (Thomas Gleixner).
 
  - Modify some computations in the intel_pstate driver to avoid
    rounding errors resulting from them (Srinivas Pandruvada).
 
  - Reduce the overhead of the intel_pstate driver in the HWP
    (hardware-managed P-states) mode and when the "performance"
    P-state selection algorithm is in use by making it avoid
    registering scheduler callbacks in those cases (Len Brown).
 
  - Rework the energy_performance_preference sysfs knob in
    intel_pstate by changing the values that correspond to
    different symbolic hint names used by it (Len Brown).
 
  - Make it possible to use more than one cpuidle driver at the same
    time on ARM (Daniel Lezcano).
 
  - Make it possible to prevent the cpuidle menu governor from using
    the 0 state by disabling it via sysfs (Nicholas Piggin).
 
  - Add support for FFH (Fixed Functional Hardware) MWAIT in ACPI C1
    on AMD systems (Yazen Ghannam).
 
  - Make the CPPC cpufreq driver take the lowest nonlinear performance
    information into account (Prashanth Prakash).
 
  - Add support for hi3660 to the cpufreq-dt driver, fix the
    imx6q driver and clean up the sfi, exynos5440 and intel_pstate
    drivers (Colin Ian King, Krzysztof Kozlowski, Octavian Purdila,
    Rafael Wysocki, Tao Wang).
 
  - Fix a few minor issues in the generic power domains (genpd)
    framework and clean it up somewhat (Krzysztof Kozlowski,
    Mikko Perttunen, Viresh Kumar).
 
  - Fix a couple of minor issues in the operating performance points
    (OPP) framework and clean it up somewhat (Viresh Kumar).
 
  - Fix a CONFIG dependency in the hibernation core and clean it up
    slightly (Balbir Singh, Arvind Yadav, BaoJun Luo).
 
  - Add rk3228 support to the rockchip-io adaptive voltage scaling
    (AVS) driver (David Wu).
 
  - Fix an incorrect bit shift operation in the RAPL power capping
    driver (Adam Lessnau).
 
  - Add support for the EPP field in the HWP (hardware managed
    P-states) control register, HWP.EPP, to the x86_energy_perf_policy
    tool and update msr-index.h with HWP.EPP values (Len Brown).
 
  - Fix some minor issues in the turbostat tool (Len Brown).
 
  - Add support for AMD family 0x17 CPUs to the cpupower tool and fix
    a minor issue in it (Sherry Hurwitz).
 
  - Assorted cleanups, mostly related to the constification of some
    data structures (Arvind Yadav, Joe Perches, Kees Cook, Krzysztof
    Kozlowski).
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABCAAGBQJZWrICAAoJEILEb/54YlRxZYMQAIRhfbyDxKq+ByvSilUS8kTA
 AItwJ8FFzykhiwN75Cqabg4rAGyWma7IRs1vzU7zeC1aEQIn+bTQtvk+utZNI+g2
 ANFlDha20q/sXsP/CDMMTIAdW9tSOC0TOvFI9s2V2Y8dJZhoekO4ctx34FAfUS5d
 Ao6rwSAWCMsCXcGaTAlqTA+TEJmBG7u6Iq6hq6ngltoFwOv3mWWBVn52VVaJ7SMp
 9/IPbbLGMFAedrgEBRGCR+MME1xZZpvcZIJaTt1Mgn7Cx3cJaysIUAvqY/SsvFGq
 5FcUTcF2qpK3+AGawiAxZIjvOBsGRtIwqKinNIzYWs/NjiIdzmgVAmTeuPtTqp+5
 HFehUdtkFcnuDnLqSNzAaZUa7tw84cJkwnbVMnesx0MkG6rZ1SeL22E2Sabpcdsh
 3Yo1ThzJSxi59DhiiE92EQnNCEjmCldRy+8q5Ag035muxl6EJYvuNBMnZv/BMCUn
 ltSNOrmps1DlN+Col8ORIeNzQ1YjYzWMqKAYzSbyccm4ug/iSHx0/DuESmQ4GTlF
 YCwkmqyWiHrBwpl51jc+4a7SGlMmKRqU+MJes0CjagaaqoUAb8qeBOpzEJ0yNwjZ
 wtI41l6blE6kbMD3yqGdCfiB2S7GlPVoxa15eX1wRyLH3fLjwwrzJirEaiBS86tI
 1PzHZEOmBlh3DYC6DBKA
 =Wsph
 -----END PGP SIGNATURE-----

Merge tag 'pm-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

Pull power management updates from Rafael Wysocki:
 "The big ticket items here are the rework of suspend-to-idle in order
  to add proper support for power button wakeup from it on recent Dell
  laptops and the rework of interfaces exporting the current CPU
  frequency on x86.

  In addition to that, support for a few new pieces of hardware is
  added, the PCI/ACPI device wakeup infrastructure is simplified
  significantly and the wakeup IRQ framework is fixed to unbreak the IRQ
  bus locking infrastructure.

  Also, there are some functional improvements for intel_pstate, tools
  updates and small fixes and cleanups all over.

  Specifics:

   - Rework suspend-to-idle to allow it to take wakeup events signaled
     by the EC into account on ACPI-based platforms in order to properly
     support power button wakeup from suspend-to-idle on recent Dell
     laptops (Rafael Wysocki).

     That includes the core suspend-to-idle code rework, support for the
     Low Power S0 _DSM interface, and support for the ACPI INT0002
     Virtual GPIO device from Hans de Goede (required for USB keyboard
     wakeup from suspend-to-idle to work on some machines).

   - Stop trying to export the current CPU frequency via /proc/cpuinfo
     on x86 as that is inaccurate and confusing (Len Brown).

   - Rework the way in which the current CPU frequency is exported by
     the kernel (over the cpufreq sysfs interface) on x86 systems with
     the APERF and MPERF registers by always using values read from
     these registers, when available, to compute the current frequency
     regardless of which cpufreq driver is in use (Len Brown).

   - Rework the PCI/ACPI device wakeup infrastructure to remove the
     questionable and artificial distinction between "devices that can
     wake up the system from sleep states" and "devices that can
     generate wakeup signals in the working state" from it, which allows
     the code to be simplified quite a bit (Rafael Wysocki).

   - Fix the wakeup IRQ framework by making it use SRCU instead of RCU
     which doesn't allow sleeping in the read-side critical sections,
     but which in turn is expected to be allowed by the IRQ bus locking
     infrastructure (Thomas Gleixner).

   - Modify some computations in the intel_pstate driver to avoid
     rounding errors resulting from them (Srinivas Pandruvada).

   - Reduce the overhead of the intel_pstate driver in the HWP
     (hardware-managed P-states) mode and when the "performance" P-state
     selection algorithm is in use by making it avoid registering
     scheduler callbacks in those cases (Len Brown).

   - Rework the energy_performance_preference sysfs knob in intel_pstate
     by changing the values that correspond to different symbolic hint
     names used by it (Len Brown).

   - Make it possible to use more than one cpuidle driver at the same
     time on ARM (Daniel Lezcano).

   - Make it possible to prevent the cpuidle menu governor from using
     the 0 state by disabling it via sysfs (Nicholas Piggin).

   - Add support for FFH (Fixed Functional Hardware) MWAIT in ACPI C1 on
     AMD systems (Yazen Ghannam).

   - Make the CPPC cpufreq driver take the lowest nonlinear performance
     information into account (Prashanth Prakash).

   - Add support for hi3660 to the cpufreq-dt driver, fix the imx6q
     driver and clean up the sfi, exynos5440 and intel_pstate drivers
     (Colin Ian King, Krzysztof Kozlowski, Octavian Purdila, Rafael
     Wysocki, Tao Wang).

   - Fix a few minor issues in the generic power domains (genpd)
     framework and clean it up somewhat (Krzysztof Kozlowski, Mikko
     Perttunen, Viresh Kumar).

   - Fix a couple of minor issues in the operating performance points
     (OPP) framework and clean it up somewhat (Viresh Kumar).

   - Fix a CONFIG dependency in the hibernation core and clean it up
     slightly (Balbir Singh, Arvind Yadav, BaoJun Luo).

   - Add rk3228 support to the rockchip-io adaptive voltage scaling
     (AVS) driver (David Wu).

   - Fix an incorrect bit shift operation in the RAPL power capping
     driver (Adam Lessnau).

   - Add support for the EPP field in the HWP (hardware managed
     P-states) control register, HWP.EPP, to the x86_energy_perf_policy
     tool and update msr-index.h with HWP.EPP values (Len Brown).

   - Fix some minor issues in the turbostat tool (Len Brown).

   - Add support for AMD family 0x17 CPUs to the cpupower tool and fix a
     minor issue in it (Sherry Hurwitz).

   - Assorted cleanups, mostly related to the constification of some
     data structures (Arvind Yadav, Joe Perches, Kees Cook, Krzysztof
     Kozlowski)"

* tag 'pm-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (69 commits)
  cpufreq: Update scaling_cur_freq documentation
  cpufreq: intel_pstate: Clean up after performance governor changes
  PM: hibernate: constify attribute_group structures.
  cpuidle: menu: allow state 0 to be disabled
  intel_idle: Use more common logging style
  PM / Domains: Fix missing default_power_down_ok comment
  PM / Domains: Fix unsafe iteration over modified list of domains
  PM / Domains: Fix unsafe iteration over modified list of domain providers
  PM / Domains: Fix unsafe iteration over modified list of device links
  PM / Domains: Handle safely genpd_syscore_switch() call on non-genpd device
  PM / Domains: Call driver's noirq callbacks
  PM / core: Drop run_wake flag from struct dev_pm_info
  PCI / PM: Simplify device wakeup settings code
  PCI / PM: Drop pme_interrupt flag from struct pci_dev
  ACPI / PM: Consolidate device wakeup settings code
  ACPI / PM: Drop run_wake from struct acpi_device_wakeup_flags
  PM / QoS: constify *_attribute_group.
  PM / AVS: rockchip-io: add io selectors and supplies for rk3228
  powercap/RAPL: prevent overridding bits outside of the mask
  PM / sysfs: Constify attribute groups
  ...
2017-07-04 13:39:41 -07:00
Linus Torvalds 362f6729cb USB/PHY patches for 4.13-rc1
Here is the big patchset of USB and PHY driver updates for 4.13-rc1.
 
 On the PHY side, they decided to move files around to "make things
 easier" in their tree.  Hopefully that wasn't a mistake, but in
 linux-next testing, we haven't had any reported problems.
 
 There's the usual set of gadget and xhci and musb updates in here as
 well, along with a number of smaller updates for a raft of different USB
 drivers.  Full details in the shortlog, nothing really major.
 
 All of these have been in linux-next for a while with no reported
 issues.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWVpavQ8cZ3JlZ0Brcm9h
 aC5jb20ACgkQMUfUDdst+ymJrgCgp8Pso8bs+bnIknUSQFSguWd3wM0AnA8X3NHf
 lrdCuqw+2oxGOQrecacz
 =5L4Q
 -----END PGP SIGNATURE-----

Merge tag 'usb-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB/PHY updates from Greg KH:
 "Here is the big patchset of USB and PHY driver updates for 4.13-rc1.

  On the PHY side, they decided to move files around to "make things
  easier" in their tree. Hopefully that wasn't a mistake, but in
  linux-next testing, we haven't had any reported problems.

  There's the usual set of gadget and xhci and musb updates in here as
  well, along with a number of smaller updates for a raft of different
  USB drivers. Full details in the shortlog, nothing really major.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'usb-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (173 commits)
  Add USB quirk for HVR-950q to avoid intermittent device resets
  USB hub_probe: rework ugly goto-into-compound-statement
  usb: host: ohci-pxa27x: Handle return value of clk_prepare_enable
  USB: serial: cp210x: add ID for CEL EM3588 USB ZigBee stick
  usbip: Fix uninitialized variable bug in vhci
  usb: core: read USB ports from DT in the usbport LED trigger driver
  dt-bindings: leds: document new trigger-sources property
  usb: typec: ucsi: Add ACPI driver
  usb: typec: Add support for UCSI interface
  usb: musb: compress return logic into one line
  USB: serial: propagate late probe errors
  USB: serial: refactor port endpoint setup
  usb: musb: tusb6010_omap: Convert to DMAengine API
  ARM: OMAP2+: DMA: Add slave map entries for 24xx external request lines
  usb: musb: tusb6010: Handle DMA TX completion in DMA callback as well
  usb: musb: tusb6010_omap: Allocate DMA channels upfront
  usb: musb: tusb6010_omap: Create new struct for DMA data/parameters
  usb: musb: tusb6010_omap: Use one musb_ep_select call in tusb_omap_dma_program
  usb: musb: tusb6010: Add MUSB_G_NO_SKB_RESERVE to quirks
  usb: musb: Add quirk to avoid skb reserve in gadget mode
  ...
2017-07-03 19:30:55 -07:00
Rafael J. Wysocki de3ef1eb1c PM / core: Drop run_wake flag from struct dev_pm_info
The run_wake flag in struct dev_pm_info is used to indicate whether
or not the device is capable of generating remote wakeup signals at
run time (or in the system working state), but the distinction
between runtime remote wakeup and system wakeup signaling has always
been rather artificial.  The only practical reason for it to exist
at the core level was that ACPI and PCI treated those two cases
differently, but that's not the case any more after recent changes.

For this reason, get rid of the run_wake flag and, when applicable,
use device_set_wakeup_capable() and device_can_wakeup() instead of
device_set_run_wake() and device_run_wake(), respectively.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
2017-06-28 01:52:52 +02:00
Greg Kroah-Hartman 24040a5837 usb: changes for v4.13 merge window
This time around we have a total of 57 non-merge commits. A list of
 most important changes follows:
 
 - Improvements to dwc3 tracing interface
 - Initial dual-role support for dwc3
 - Improvements to how we handle DMA resources in dwc3
 - A new f_uac1 implementation which much more flexible
 - Removal of AVR32 bits
 - Improvements to f_mass_storage driver
 -----BEGIN PGP SIGNATURE-----
 
 iQJRBAABCAA7FiEElLzh7wn96CXwjh2IzL64meEamQYFAllHcK0dHGZlbGlwZS5i
 YWxiaUBsaW51eC5pbnRlbC5jb20ACgkQzL64meEamQbRQQ//as9W89twbmwOqaSU
 pXlbR/gmmEjD6POLWM2GuG3jH8oD3pQq7ZxH22YEFx8Z4wN7vPJ67JJkyoSfhAui
 ppnp6AbSPiNolZRb5nTnASnq0cJiTE/rbSM5s1wpe+Qa3ZoQgTHhipnL1/qf8SgR
 PN1wgUTGeXxiIA00iOYTG2pjM+OvFO5UpqFJCfh4vuEjcdBWvHDXTUwga5G+qwIa
 pgNECcmUsXmHimp6jE+qLUhRYOqvTEC+lc9nzZj4MCru3PDEhZYuOah0XrepiNKU
 NB49DVMtDwaGXrKPwa6rNWD8JZF0CAsShvO6V/2p1peInJZUuIrEjXYRUlkPQt9G
 yLzxBS+asLCBauzxBFNPrR2BFfJ2uyUCLHYiKP2UbRfWCBFo84MDJCUWACL1aKCH
 YLeM1Q7Urxp5suirr2UmwBJdUxXNTncEXsKrtGcrNndKt/Uq8/DxcrbZ2/6ANTDT
 wdzm8gSSjtQaFLRc5KgAqrX/ClfEDgQwfgq0DXn9cKxZ9E9xID45s71feKEoBI42
 6S/oAopSuBsEmTsPTy0WLR8MTJG3MoJAdr/mHau11Tl0k9qr9KKnHbdUjji9CF6E
 aGcV40nKqp9Bd4bcbCNB6NsJUB+zcN7t0bjTsPZQH3XOCSS+fF7oJ6+SIxhsKAFT
 rHRl6RhLOIP0vZ0UIsDzeDttCVM=
 =v6a5
 -----END PGP SIGNATURE-----

Merge tag 'usb-for-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing

Felipe writes:

usb: changes for v4.13 merge window

This time around we have a total of 57 non-merge commits. A list of
most important changes follows:

- Improvements to dwc3 tracing interface
- Initial dual-role support for dwc3
- Improvements to how we handle DMA resources in dwc3
- A new f_uac1 implementation which much more flexible
- Removal of AVR32 bits
- Improvements to f_mass_storage driver
2017-06-20 11:39:34 +08:00
Arvind Yadav ece7af5f78 usb: dwc3: exynos: Handle return value of clk_prepare_enable
clk_prepare_enable() can fail here and we must check its return value.

Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-06-15 11:10:27 +03:00
Andy Shevchenko 46b780d46b usb: dwc3: gadget: increase readability of dwc3_gadget_init_endpoints()
The commit 47d3946ea2

	usb: dwc3: refactor gadget endpoint count calculation

refactored dwc3_gadget_init_endpoints() and in particular changed in or
out endpoint numbering to be through. It's not always convenient and
makes code a slightly harder to read.

Introduce a new temporary variable to make it easier to understand what
is going on inside the function.

While doing that, rename local variables as follows:
	u8 num	-> u8 total
	int num -> int kbytes

Replace implicit direction check via epnum with explicit use of
direction variable.

While here, replace %d to %u when compounding endpoint name since we are
using unsigned type.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-06-13 13:21:08 +03:00
Felipe Balbi 958d1a4c40 usb: dwc3: core: program PHY for proper DRD modes
If PHY is entering Host mode, we need to enable VBUS.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-06-13 13:21:06 +03:00
Felipe Balbi f54edb539c usb: dwc3: core: initialize ULPI before trying to get the PHY
If don't reorder initialization like this, we will never be able to
get a reference to ULPI PHYs.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-06-13 13:21:06 +03:00
Felipe Balbi e0082698b6 usb: dwc3: ulpi: conditionally resume ULPI PHY
If PHY is suspended by the time we want to issue ULPI transfers, we
will observe timeouts on the ULPI interface. In order to avoid such
issue, let's make sure PHY is resumed before issuing a ULPI transfer.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-06-13 13:21:05 +03:00
Felipe Balbi 9b0a1f95c4 usb: dwc3: ep0: make sure wValue is 0 on GetStatus()
We don't (yet) support PTM_STATUS messages so let's not reply to them
erroneously.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-06-13 13:21:05 +03:00
Felipe Balbi 7d8d063956 usb: dwc3: gadget: implement ->udc_set_speed()
Use this method to make sure we don't try to connect on speeds not
supported by the gadget driver.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-06-13 13:21:03 +03:00
Andy Shevchenko 94116f8126 ACPI: Switch to use generic guid_t in acpi_evaluate_dsm()
acpi_evaluate_dsm() and friends take a pointer to a raw buffer of 16
bytes. Instead we convert them to use guid_t type. At the same time we
convert current users.

acpi_str_to_uuid() becomes useless after the conversion and it's safe to
get rid of it.

Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Cc: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
2017-06-07 12:20:49 +02:00
Felipe Balbi af32423a2d usb: dwc3: trace: decode ctrl request
Instead of *always* dumping raw ctrl bytes, let's decode standard
requests which will make the lives of those debugging DWC3 quite a bit
easier.

Output will now look like so:

irq/34-dwc3-1594  [000] d..1   107.573081: dwc3_ctrl_req: Get Device Descriptor(Index = 0, Length = 18)
irq/34-dwc3-1594  [000] d..1   107.573694: dwc3_ctrl_req: Set Address(Addr = 01)
irq/34-dwc3-1594  [000] d..1   107.588319: dwc3_ctrl_req: Get Device Descriptor(Index = 0, Length = 18)
irq/34-dwc3-1594  [000] d..1   107.588816: dwc3_ctrl_req: Get Configuration Descriptor(Index = 0, Length = 9)
irq/34-dwc3-1594  [000] d..1   107.589191: dwc3_ctrl_req: Set Configuration(Config = 3)
irq/34-dwc3-1594  [000] d..1   107.589846: dwc3_ctrl_req: Get BOS Descriptor(Index = 0, Length = 5)
irq/34-dwc3-1594  [000] d..1   107.590146: dwc3_ctrl_req: Get BOS Descriptor(Index = 0, Length = 22)
irq/34-dwc3-1594  [000] d..1   107.590546: dwc3_ctrl_req: Get Configuration Descriptor(Index = 0, Length = 9)
irq/34-dwc3-1594  [000] d..1   107.590840: dwc3_ctrl_req: Get Configuration Descriptor(Index = 0, Length = 69)
irq/34-dwc3-1594  [000] d..1   107.591138: dwc3_ctrl_req: Get Configuration Descriptor(Index = 1, Length = 9)
irq/34-dwc3-1594  [000] d..1   107.591541: dwc3_ctrl_req: Get Configuration Descriptor(Index = 1, Length = 32)
irq/34-dwc3-1594  [000] d..1   107.591834: dwc3_ctrl_req: Get Device Descriptor(Index = 0, Length = 18)
irq/34-dwc3-1594  [000] d..1   114.701005: dwc3_ctrl_req: Get Device Descriptor(Index = 0, Length = 18)
irq/34-dwc3-1594  [000] d..1   114.721080: dwc3_ctrl_req: Get Device Descriptor(Index = 0, Length = 18)
irq/34-dwc3-1594  [000] d..1   114.722709: dwc3_ctrl_req: Get Device Descriptor(Index = 0, Length = 18)
irq/34-dwc3-1594  [000] d..1   114.728979: dwc3_ctrl_req: Get Device Descriptor(Index = 0, Length = 18)
irq/34-dwc3-1594  [000] d..1   114.730544: dwc3_ctrl_req: Get Device Qualifier Descriptor(Index = 0, Length = 10)
irq/34-dwc3-1594  [000] d..1   115.776018: dwc3_ctrl_req: Get Configuration Descriptor(Index = 0, Length = 9)
irq/34-dwc3-1594  [000] d..1   115.776760: dwc3_ctrl_req: Set Configuration(Config = 0)
irq/34-dwc3-1594  [000] d..1   115.777676: dwc3_ctrl_req: Get Configuration(Length = 1)
irq/34-dwc3-1594  [000] d..1   115.924797: dwc3_ctrl_req: Get Device Descriptor(Index = 0, Length = 18)
irq/34-dwc3-1594  [000] d..1   115.929025: dwc3_ctrl_req: Get String Descriptor(Index = 0, Length = 500)
irq/34-dwc3-1594  [000] d..1   115.929566: dwc3_ctrl_req: Get String Descriptor(Index = 1, Length = 500)
irq/34-dwc3-1594  [000] d..1   115.930911: dwc3_ctrl_req: Get String Descriptor(Index = 0, Length = 500)
irq/34-dwc3-1594  [000] d..1   115.931528: dwc3_ctrl_req: Get String Descriptor(Index = 2, Length = 500)
irq/34-dwc3-1594  [000] d..1   115.932950: dwc3_ctrl_req: Get String Descriptor(Index = 0, Length = 500)
irq/34-dwc3-1594  [000] d..1   115.933533: dwc3_ctrl_req: Get String Descriptor(Index = 3, Length = 500)

Note that Class and Vendor requests won't be decoded for obvious
reasons. Those will be printed as a raw sequence of bytes.

This patch has been tested against a normal host (both Linux and
Windows) and USB30CV Chapter 9 tests.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-06-02 11:22:29 +03:00
Felipe Balbi 3587f36a12 usb: dwc3: debug: remove static char buffer from dwc3_decode_event()
Instead, we can require caller to pass a buffer for the function to
use. This cleans things quite a bit.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-06-02 11:22:29 +03:00
Felipe Balbi e42f09b85f usb: dwc3: trace: rely on __string() and __assign_str()
Instead of going for a 512 byte buffer and using snprintf(), let's
rely on helps __string() and __assign_str() where possible.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-06-02 11:22:29 +03:00
Felipe Balbi dfc5e80578 usb: dwc3: gadget: slight cleanup to dwc3_process_event_entry()
No functional changes, just a slight readability improvement.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-06-02 11:22:28 +03:00
Felipe Balbi 436841d53d usb: dwc3: debugfs: slightly improve output of trb_ring
Instead of printing out enqueue and dequeue pointer value as a header
to the output, let's mark the TRBs in question with 'E' and 'D'. The
output looks slightly easier to read.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-06-02 11:22:28 +03:00
Felipe Balbi bfad65ee9b usb: dwc3: update documentation
No functional changes, just making sure we can use these for ReST docs
later.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-06-02 11:22:27 +03:00
Felipe Balbi 04fb365c45 usb: dwc3: replace %p with %pK
%p will leak kernel pointers, so let's not expose the information on
dmesg and instead use %pK. %pK will only show the actual addresses if
explicitly enabled under /proc/sys/kernel/kptr_restrict.

Cc: <stable@vger.kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-06-02 11:22:10 +03:00
William Wu 65db7a0c98 usb: dwc3: add disable u2mac linestate check quirk
This patch adds a quirk to disable USB 2.0 MAC linestate check
during HS transmit. Refer the dwc3 databook, we can use it for
some special platforms if the linestate not reflect the expected
line state(J) during transmission.

When use this quirk, the controller implements a fixed 40-bit
TxEndDelay after the packet is given on UTMI and ignores the
linestate during the transmit of a token (during token-to-token
and token-to-data IPGAP).

On some rockchip platforms (e.g. rk3399), it requires to disable
the u2mac linestate check to decrease the SSPLIT token to SETUP
token inter-packet delay from 566ns to 466ns, and fix the issue
that FS/LS devices not recognized if inserted through USB 3.0 HUB.

Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-05-17 14:16:57 +03:00
Felipe Balbi cdb55b39fa usb: dwc3: gadget: lazily map requests for DMA
Some functions might want to have very, very long request queues. We
can't make any assumptions about how many requests we *are* able to
map, so instead of mapping requests early, let's map them late. This
way, functions can queue as many requests as they'd like but we won't
take DMA resources until they are needed.

Also, we can now stop processing requests when we run out of DMA
resources but still keep requests in the queue for late processing.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-05-17 13:21:14 +03:00
Felipe Balbi 202adafe5a usb: dwc3: gadget: don't WARN about lack of TRBs
We don't need a big fat warning with stack dump at all. Running out of
TRBs is a normal condition and we will have more TRBs available as
soon as some transfers complete.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-05-17 13:20:51 +03:00
Pan Bian 018047a1db usb: dwc3: keystone: check return value
Function devm_clk_get() returns an ERR_PTR when it fails. However, in
function kdwc3_probe(), its return value is not checked, which may
result in a bad memory access bug. This patch fixes the bug.

Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-05-16 14:11:04 +03:00
Thinh Nguyen d325a1de49 usb: dwc3: gadget: Prevent losing events in event cache
The dwc3 driver can overwite its previous events if its top-half IRQ
handler (TH) gets invoked again before processing the events in the
cache. We see this as a hang in the file transfer and the host will
attempt to reset the device. TH gets the event count and deasserts the
interrupt line by writing DWC3_GEVNTSIZ_INTMASK to DWC3_GEVNTSIZ. If
there's a new event coming between reading the event count and interrupt
deassertion, dwc3 will lose previous pending events. More generally, we
will see 0 event count, which should not affect anything.

This shouldn't be possible in the current dwc3 implementation. However,
through testing and reading the PCIe trace, the TH occasionally still
gets invoked one more time after HW interrupt deassertion. (With PCIe
legacy interrupts, TH is called repeatedly as long as the interrupt line
is asserted). We suspect that there is a small detection delay in the
SW.

To avoid this issue, Check DWC3_EVENT_PENDING flag to determine if the
events are processed in the bottom-half IRQ handler. If not, return
IRQ_HANDLED and don't process new event.

Cc: stable@vger.kernel.org
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-05-16 14:11:03 +03:00
Roger Quadros f1d6826cae usb: dwc3: gadget: Fix ISO transfer performance
Commit 08a36b5438 ("usb: dwc3: gadget: simplify __dwc3_gadget_ep_queue()")
caused a small change in the way ISO transfer is handled in the case
when XferInProgress event happens on Isoc EP with an active transfer.
This caused a performance degradation of 50%. e.g. using g_webcam on DUT
and luvcview on host the video frame rate dropped from 16fps to 8fps
@high-speed.

Make the ISO transfer handling equivalent to that prior to that commit
to get back the original ISO performance numbers.

Fixes: 08a36b5438 ("usb: dwc3: gadget: simplify __dwc3_gadget_ep_queue()")
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-05-16 14:11:03 +03:00
Heikki Krogerus 682179592e usb: dwc3: pci: add Intel Cannonlake PCI IDs
Intel Cannonlake PCH has the same DWC3 than Intel
Sunrisepoint. Add the new IDs to the supported devices.

Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-05-16 14:11:03 +03:00
Linus Torvalds 8f28472a73 USB patches for 4.12-rc1
Here is the big USB patchset for 4.12-rc1.
 
 Lots of good stuff here, after many many many attempts, the kernel
 finally has a working typeC interface, many thanks to the Heikki and
 Guenter and others who have taken the time to get this merged.  It
 wasn't an easy path for them at all.
 
 There's also a staging driver that uses this new api, which is why it's
 coming in through this tree.
 
 Along with that, there's the usual huge number of changes for gadget
 drivers, xhci, and other stuff.  Johan also finally refactored pretty
 much every driver that was looking at USB endpoints to do it in a common
 way, which will help prevent any "badly-formed" devices from causing
 problems in drivers.  That too wasn't a simple task.
 
 All of these have been in linux-next for a while with no reported
 issues.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWQvEIQ8cZ3JlZ0Brcm9h
 aC5jb20ACgkQMUfUDdst+yny4gCePCXxnrQdMWE+IMXf1H1hMubLkVkAn0ZWgQkq
 BspgO7ZmGb+9Fpf6YvNz
 =nwAu
 -----END PGP SIGNATURE-----

Merge tag 'usb-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB updates from Greg KH:
 "Here is the big USB patchset for 4.12-rc1.

  Lots of good stuff here, after many many many attempts, the kernel
  finally has a working typeC interface, many thanks to Heikki and
  Guenter and others who have taken the time to get this merged. It
  wasn't an easy path for them at all.

  There's also a staging driver that uses this new api, which is why
  it's coming in through this tree.

  Along with that, there's the usual huge number of changes for gadget
  drivers, xhci, and other stuff. Johan also finally refactored pretty
  much every driver that was looking at USB endpoints to do it in a
  common way, which will help prevent any "badly-formed" devices from
  causing problems in drivers. That too wasn't a simple task.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'usb-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
  staging: typec: Fairchild FUSB302 Type-c chip driver
  staging: typec: Type-C Port Controller Interface driver (tcpci)
  staging: typec: USB Type-C Port Manager (tcpm)
  usb: host: xhci: remove #ifdef around PM functions
  usb: musb: don't mark of_dev_auxdata as initdata
  usb: misc: legousbtower: Fix buffers on stack
  USB: Revert "cdc-wdm: fix "out-of-sync" due to missing notifications"
  usb: Make sure usb/phy/of gets built-in
  USB: storage: e-mail update in drivers/usb/storage/unusual_devs.h
  usb: host: xhci: print correct command ring address
  usb: host: xhci: delete sp_dma_buffers for scratchpad
  usb: host: xhci: using correct specification chapter reference for DCBAAP
  xhci: switch to pci_alloc_irq_vectors
  usb: host: xhci-plat: set resume_quirk() for R-Car controllers
  usb: host: xhci-plat: add resume_quirk()
  usb: host: xhci-plat: enable clk in resume timing
  usb: host: plat: Enable xHCI plat runtime PM
  USB: serial: ftdi_sio: add device ID for Microsemi/Arrow SF2PLUS Dev Kit
  USB: serial: constify static arrays
  usb: fix some references for /proc/bus/usb
  ...
2017-05-04 18:03:51 -07:00
Linus Torvalds 2bd8040174 This is the bulk of GPIO changes for the v4.12 kernel cycle:
Core changes
 
 - Return NULL from gpiod_get_optional() when GPIOLIB is disabled.
   This was a much discussed change. It affects use cases where people
   write drivers that might or might not be using GPIO resources.
   I have decided that this is the lesser evil right now.
 
 - Make gpiod_count() behave consistently across different hardware
   descriptions.
 
 - Fix the syntax around open drain/open source to not infer active
   high/low semantics.
 
 New drivers
 
 - A new single-register fixed-direction framework driver for hardware
   that have lines controlled by a single register that just work in
   one direction (out or in), including IRQ support.
 
 - Support the Fintek F71889A GPIO SuperIO controller.
 
 - Support the National NI 169445 MMIO GPIO.
 
 - Support for the X-Gene derivative of the DWC GPIO controller
 
 - Support for the Rohm BD9571MWV-M PMIC GPIO controller.
 
 - Refactor the Gemini GPIO driver to a generic Faraday FTGPIO driver
   and replace both the Gemini and the Moxa ART custom drivers with
   this driver.
 
 Driver improvements
 
 - A whole slew of drivers have their spinlocks chaned to raw spinlocks
   as they provide irqchips, and thus we are progressing on realtime
   compliance.
 
 - Use devm_irq_alloc_descs() in a slew of drivers, getting managed
   resources.
 
 - Support for the embedded PWM controller inside the MVEBU driver.
 
 - Debounce, open source and open drain support for the Aspeed driver.
 
 - Misc smaller fixes like spelling and syntax and whatnot.
 -----BEGIN PGP SIGNATURE-----
 
 iQIcBAABAgAGBQJZCusBAAoJEEEQszewGV1zengP/i3YgmSXJdaf26t/NxG3klU3
 qx3akdQ3gEQ6BOlIY7Ew+b6qgMJynYNZa1trZgqTgLxPEKWjidyCgz+LHQ0OY+ir
 a7x6wr+gBj5WlgV+nBjVs4l6W8pVKCfnap/04OPEQDpxZOHs2LU5pqxxUZ9AxkKS
 urDFMDX55baFviQ+xAuHgamok87YoGP36A/e/fHIBepZmnochf0mCcPfIh0t8lRh
 s2x29PN5ZFRkl403RzjZfVCEMr9bMnSqmDquvPO++Kq0bL+3rOhuMErocd1Bg8ao
 LxBktkryujTaw699xK7Rq5SwcnOAPpaBY4NTmwsIJvAJuCh7qLy9JxQSBsSOT2bx
 61NWUt5T/Xsi0ECYZM4YvsNpUP6XrpSTyG3c8T3fY9vXYLNKZBv1ht6OODpLeuke
 DxULAWP+DdzUS8a3qfKQvIJzSTloU31a1MBG58DWNJ072EQfa2YNaVE75VQk/z5/
 0xZbSHdPY/0Xgx8ltpKu37bSO676JiVQZZ1HEAuti4h21+USYueYD2L8/Bx4k9e/
 4UaOcw3MaCDHP/sf5hg17kQBjhhS0lV9Zv6H9QbHZUocJTJlIU+vXtgkQlrfi3n8
 8j5m+ywVarmLtPqg1j2rqcw7LBCPe0qRXH3e5X/YmNMc3rH9bQz4cTo8ZSN9r8zS
 c17zGbbAqlGsBkpFAbQz
 =DGPb
 -----END PGP SIGNATURE-----

Merge tag 'gpio-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

Pull GPIO updates from Linus Walleij:
 "This is the bulk of GPIO changes for the v4.12 kernel cycle.

  Core changes:

   - Return NULL from gpiod_get_optional() when GPIOLIB is disabled.
     This was a much discussed change. It affects use cases where people
     write drivers that might or might not be using GPIO resources. I
     have decided that this is the lesser evil right now.

   - Make gpiod_count() behave consistently across different hardware
     descriptions.

   - Fix the syntax around open drain/open source to not infer active
     high/low semantics.

  New drivers:

   - A new single-register fixed-direction framework driver for hardware
     that have lines controlled by a single register that just work in
     one direction (out or in), including IRQ support.

   - Support the Fintek F71889A GPIO SuperIO controller.

   - Support the National NI 169445 MMIO GPIO.

   - Support for the X-Gene derivative of the DWC GPIO controller

   - Support for the Rohm BD9571MWV-M PMIC GPIO controller.

   - Refactor the Gemini GPIO driver to a generic Faraday FTGPIO driver
     and replace both the Gemini and the Moxa ART custom drivers with
     this driver.

  Driver improvements:

   - A whole slew of drivers have their spinlocks chaned to raw
     spinlocks as they provide irqchips, and thus we are progressing on
     realtime compliance.

   - Use devm_irq_alloc_descs() in a slew of drivers, getting managed
     resources.

   - Support for the embedded PWM controller inside the MVEBU driver.

   - Debounce, open source and open drain support for the Aspeed driver.

   - Misc smaller fixes like spelling and syntax and whatnot"

* tag 'gpio-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (77 commits)
  gpio: f7188x: Add a missing break
  gpio: omap: return error if requested debounce time is not possible
  gpio: Add ROHM BD9571MWV-M PMIC GPIO driver
  gpio: gpio-wcove: fix GPIO IRQ status mask
  gpio: DT bindings, move tca9554 from pcf857x to pca953x
  gpio: move tca9554 from pcf857x to pca953x
  gpio: arizona: Correct check whether the pin is an input
  gpio: Add XRA1403 DTS binding documentation
  dt-bindings: add exar to vendor prefixes list
  gpio: gpio-wcove: fix irq pending status bit width
  gpio: dwapb: use dwapb_read instead of readl_relaxed
  gpio: aspeed: Add open-source and open-drain support
  gpio: aspeed: Add debounce support
  gpio: aspeed: dt: Add optional clocks property
  gpio: aspeed: dt: Fix description alignment in bindings document
  gpio: mvebu: Add limited PWM support
  gpio: Use unsigned int for interrupt numbers
  gpio: f7188x: Add F71889A GPIO support.
  gpio: core: Decouple open drain/source flag with active low/high
  gpio: arizona: Correct handling for reading input GPIOs
  ...
2017-05-04 12:05:32 -07:00
Greg Kroah-Hartman ba7756d082 usb: changes for v4.12
With 51 non-merge commits, this is one of the smallest USB Gadget pull
 requests. Apart from your expected set of non-critical fixes, and
 other miscellaneous items, we have most of the changes in dwc3 (52.5%)
 with all other UDCs following with 34.8%.
 
 As for the actual changes, the most important of them are all the
 recent changes to reduce memory footprint of dwc3, bare minimum
 dual-role support on dwc3 and reworked endpoint count and
 initialization routines.
 -----BEGIN PGP SIGNATURE-----
 
 iQJRBAABCAA7FiEElLzh7wn96CXwjh2IzL64meEamQYFAljsjRwdHGZlbGlwZS5i
 YWxiaUBsaW51eC5pbnRlbC5jb20ACgkQzL64meEamQaPZA/9H6GgNlvdGWPweJ0r
 g86iBmio/Qn334SOCAJDrdw4ULSTSQR8nQHGWuETE2pQ2uYA/dbBWvjkx8Pujs+u
 Ye2ig/iYchvHhY7cIWBG6A/iwvBClZF+yTv4ruh3i99BOGeAtGSyFS3HftQZLkGs
 360CritNs+fSJsU6jnCE2+808evbkRiMaEfiBpiqXF2wvjMonWUMUlHaTBTHzDnk
 k2/NJSzDINr4HaALalJxVpEetC500LDkQ531O5s7V6NIareCIBOh2li9xZJur38h
 728BbCIiwPrdfLI2gGJLUOJq5vf5fJPT6DMJDN4hsu7gXcl2GiIc3nqlcxBB8P9R
 kurWgjVd8aIGS7qqZzfDBH7I5UgFbJZbtVXy6UhSRILF+hzAb/l95pZUOyTwUnbj
 ew3ALD2H7XolJT9jLG/q1CaQQMjudVnhLF2s1Ota8dsBeOShH6yfS6hGGQ8L1j8x
 kXe3dl4HEj9s7gT0S+tVN+kt6bLGZ013CjCbuZgG9JLRkswyn780KTgL4pbjHiAE
 KNGlCGUPRh3AiDLSbQ4IRU/J/0MVFs51k8aPn6PWpUqU8nc1QNEfczqrlAGPvkqU
 nE77OktC1UCTrId7F8kllTEglOrR4CVXuT2N7rYzwgM2jmfHLzb0DaJ+a/ZdsUfI
 DjuY8jNbuGnvZRRiVQU5ynva5BU=
 =wYOI
 -----END PGP SIGNATURE-----

Merge tag 'usb-for-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next

Felipe writes:

usb: changes for v4.12

With 51 non-merge commits, this is one of the smallest USB Gadget pull
requests. Apart from your expected set of non-critical fixes, and
other miscellaneous items, we have most of the changes in dwc3 (52.5%)
with all other UDCs following with 34.8%.

As for the actual changes, the most important of them are all the
recent changes to reduce memory footprint of dwc3, bare minimum
dual-role support on dwc3 and reworked endpoint count and
initialization routines.
2017-04-11 16:47:26 +02:00
Roger Quadros 9840354ff4 usb: dwc3: Add dual-role support
If dr_mode is "otg" then support dual role mode of operation.
Currently this mode is only supported when an extcon handle is
present in the dwc3 device tree node. This is needed to
get the ID status events of the port.

We're using a workqueue to manage the dual-role state transitions
as the extcon notifier (dwc3_drd_notifier) is called in an atomic
context by extcon_sync() and this doesn't go well with
usb_del_gadget_udc() causing a lockdep and softirq warning.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-04-11 10:58:31 +03:00
Roger Quadros 41ce1456e1 usb: dwc3: core: make dwc3_set_mode() work properly
We can't have both Host and Peripheral roles active at the same time
because of one detail on DWC3: it shares the same memory area for both
Host and Peripheral registers.

When swapping roles we must reinitialize the new role every
time. Let's make sure this works for our debugfs interface.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-04-11 10:58:30 +03:00
Roger Quadros b202c42cbf usb: dwc3: debugfs: remove unnecessary | operator
Each role is mutually exclusive, the | operator is unnecessary. Remove
it.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-04-11 10:58:30 +03:00
Roger Quadros 6b3261a274 usb: dwc3: core: add current_dr_role member
We're going to use this member to track which role we're currently
playing, that way we can more easily implement dual-role swap in
upcoming patches.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-04-11 10:58:30 +03:00
Felipe Balbi d6e5a549cc usb: dwc3: simplify ZLP handling
It's much simpler to just add one extra TRB chained to previous TRB to
handle ZLP. This helps us reduce pointless allocations and simplifies
the code a little bit.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-04-11 10:58:29 +03:00
Felipe Balbi 4199c5f8bc usb: dwc3: ep0: improve handling of unaligned OUT requests
Just like we did for all other endpoint types, let's rely on a chained
TRB pointing to ep0_bounce_addr in order to align transfer size. This
will make the code simpler.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-04-11 10:58:28 +03:00
Felipe Balbi d686a5ff6a usb: dwc3: ep0: pass dep as argument to internal functions
Instead of constantly recomputing how dwc and epnum relate to dep,
just pass dep as argument.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-04-11 10:58:28 +03:00
Felipe Balbi 7d5e650a5f usb: dwc3: ep0: use immediate SETUP on TRB
If we pass TRB's own address on bpl/bph fields, we can get our SETUP
packet as immediate data on the TRB itself, without having to allocate
extra memory for it.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-04-11 10:58:28 +03:00
Felipe Balbi b5c7ed5cca usb: dwc3: expose dwc3_trb_type_string()
That helper can be used from our tracepoint interface with very minor
edits. Let's do so.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-04-11 10:58:26 +03:00
Felipe Balbi 90abb425d9 usb: dwc3: debugfs: return strings that match tracepoints
In order to improve usability a tiny bit, we will return strings that
match what our tracepoints return.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-04-11 10:58:26 +03:00
Felipe Balbi 26c9f3e391 usb: dwc3: debugfs: make use of dwc3_gadget_link_string()
Instead of redecoding link state into a string, use our helper.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-04-11 10:58:26 +03:00
Felipe Balbi 2df301cd3d usb: dwc3: debugfs: downcase OTG on 'mode' file
When writing, we expect the "otg" string. When showing, we return
"OTG". Let's downcase that word to avoid confusion.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-04-11 10:58:25 +03:00
Roger Quadros ff3f0789b3 usb: dwc3: use BIT() macro where possible
To avoid checkpatch warnings with new patches let's
start using the BIT() macro wherever possible.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-04-11 10:58:23 +03:00
Felipe Balbi aad7c25964 usb: dwc3: trace: change format for string to cmd trace
a %x is much easier for a human to parse when reading tracepoint
output. Let's change it.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-04-11 10:58:20 +03:00
John Youn af771d731b usb: dwc3: gadget: Fix starting microframe for ISOC
The gadget wants to set the starting microframe for the first ISOC TRB
to 4 microframes in the future, but it does so by multiplying the
dep->interval. This only works if dep->interval = 1. For other intervals
it will put it 4 *intervals* in the future which may be way too much.

Fix so that it always adds just one interval or at least 4 microframes.

Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-04-11 10:58:19 +03:00
Shuah Khan 3a932b0f50 usb: dwc3: exynos: change goto labels to meaningful names
Change goto labels to meaningful names from a series of errNs.

Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-04-11 10:58:19 +03:00
Bryan O'Donoghue f3bcfc7e68 usb: dwc3: remove dwc3_gadget_init_hw_endpoints
A previous patch in the series reduces the number of  callsites of
dwc3_gadget_init_hw_endpoints from two to one. This patch removes the
redundant step of wrappering one function in the other, which can be done
by adding a parameter to dwc3_gadget_init_endpoints and moving the
linked-list initialization of dwc->gadet.ep_list.

Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-04-11 10:58:18 +03:00
Bryan O'Donoghue 47d3946ea2 usb: dwc3: refactor gadget endpoint count calculation
- DWC_USB3_NUM indicates the number of Device mode single directional
  endpoints, including OUT and IN endpoint 0.

- DWC_USB3_NUM_IN_EPS indicates the maximum number of Device mode IN
  endpoints active at any time, including control endpoint 0.

It's possible to configure RTL such that DWC_USB3_NUM_EPS is equal to
DWC_USB3_NUM_IN_EPS.

dwc3-core calculates the number of OUT endpoints as DWC_USB3_NUM minus
DWC_USB3_NUM_IN_EPS. If RTL has been configured with DWC_USB3_NUM_IN_EPS
equal to DWC_USB3_NUM then dwc3-core will calculate the number of OUT
endpoints as zero.

For example a from dwc3_core_num_eps() shows:
[    1.565000]  /usb0@f01d0000: found 8 IN and 0 OUT endpoints

This patch refactors the endpoint calculation down to one variable
dwc->num_eps taking care to maintain the current mapping of endpoints for
fixed FPGA configurations as described in Table 4-7 of version 2.60a of the
DWC USB3 databook.

The endpoint mapping will then be EP-OUT, EP-IN etc, up to DWC_USB3_NUM.
If DWC_USB3_NUM is odd then OUT will take the extra endpoint.

Suggested-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-04-11 10:58:18 +03:00
Roger Quadros 8261bd4e91 usb: dwc3: make macros safe to expression arguments
We must make sure that our macros are safe against expressions passed
as arguments. We have seen one problem where GTXFIFOSIZ(n) was failing
when passed the expression (epnum >> 1) as argument. The problem was
caused by operator precedence between >> and *.

To make sure macros are safe, we just wrap argument with () when using
it.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-04-11 10:58:18 +03:00
Lu Baolu 05428ba983 usb: dwc3: remove dwc3_log_msg trace class
dwc3_log_msg trace class isn't used any more. Suggest to remove it.

Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-03-27 10:46:34 +03:00
Felipe Balbi 1966b8657d usb: dwc3: make sure UX_EXIT_PX is cleared
This bit is only supposed to be used with known
buggy PHYs, however some platforms might erroneously
set it. In order to avoid it, let's make sure this
bit is always cleared. If some PHY needs this, we
will need to add a quirk flag.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-03-27 10:46:33 +03:00
Greg Kroah-Hartman e47ff590cc Merge 4.11-rc4 into usb-next
This resolves a merge issue in the gadget code, and we want the USB
fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-03-27 09:19:32 +02:00
Andy Shevchenko 4a56e413b5 usb: dwc3: pci: Switch to devm_acpi_dev_add_driver_gpios()
Switch to use managed variant of acpi_dev_add_driver_gpios() to simplify
error path and fix potentially wrong assignment if ->probe() fails.

While here, add a debug message in case assignment fails to allow user
see the cause of a potential issue.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-03-23 13:39:13 +01:00
Janusz Dziedzic de288e36fe usb: dwc3: gadget: delay unmap of bounced requests
In the case of bounced ep0 requests, we must delay DMA operation until
after ->complete() otherwise we might overwrite contents of req->buf.

This caused problems with RNDIS gadget.

Signed-off-by: Janusz Dziedzic <januszx.dziedzic@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-03-22 11:20:36 +02:00
yuan linyu 2c93e790e8 usb: add CONFIG_USB_PCI for system have both PCI HW and non-PCI based USB HW
a lot of embeded system SOC (e.g. freescale T2080) have both
PCI and USB modules. But USB module is controlled by registers directly,
it have no relationship with PCI module.

when say N here it will not build PCI related code in USB driver.

Signed-off-by: yuan linyu <Linyu.Yuan@alcatel-sbell.com.cn>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-03-17 13:16:56 +09:00
Felipe Balbi 35b2719e72 usb: dwc3: gadget: make to increment req->remaining in all cases
Sometimes, we might get a completion for a TRB which is left with HWO
bit. Even in these cases, we should increment req->remaining to
properly report total transferred size. I noticed this while debuggin
a separate problem seen with MSC tests from USBCV. Sometimes we would
erroneously report a completion for a 512-byte transfer when, in
reality, we transferred 0 bytes.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-03-08 13:56:37 +02:00
Roger Quadros 0913750f9f usb: dwc3-omap: Fix missing break in dwc3_omap_set_mailbox()
We need to break from all cases if we want to treat
each one of them separately.

Reported-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Fixes: d2728fb3e0 ("usb: dwc3: omap: Pass VBUS and ID events transparently")
Cc: <stable@vger.kernel.org> #v4.8+
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-03-06 16:59:34 +02:00
Roger Quadros 1551e35ea4 usb: dwc3: gadget: Fix system suspend/resume on TI platforms
On TI platforms (dra7, am437x), the DWC3_DSTS_DEVCTRLHLT bit is not set
after the device controller is stopped via DWC3_DCTL_RUN_STOP.

If we don't disconnect and stop the gadget, it stops working after a
system resume with the trace below.

There is no point in preventing gadget disconnect and gadget stop during
system suspend/resume as we're going to suspend in any case, whether
DEVCTRLHLT timed out or not.

[  141.727480] ------------[ cut here ]------------
[  141.732349] WARNING: CPU: 1 PID: 2135 at drivers/usb/dwc3/gadget.c:2384 dwc3_stop_active_transfer.constprop.4+0xc4/0xe4 [dwc3]
[  141.744299] Modules linked in: usb_f_ss_lb g_zero libcomposite xhci_plat_hcd xhci_hcd usbcore dwc3 evdev udc_core m25p80 usb_common spi_nor snd_soc_davinci_mcasp snd_soc_simple_card snd_soc_edma snd_soc_tlv3e
[  141.792163] CPU: 1 PID: 2135 Comm: irq/456-dwc3 Not tainted 4.10.0-rc8 #1138
[  141.799547] Hardware name: Generic DRA74X (Flattened Device Tree)
[  141.805940] [<c01101b4>] (unwind_backtrace) from [<c010c31c>] (show_stack+0x10/0x14)
[  141.814066] [<c010c31c>] (show_stack) from [<c04a0918>] (dump_stack+0xac/0xe0)
[  141.821648] [<c04a0918>] (dump_stack) from [<c013708c>] (__warn+0xd8/0x104)
[  141.828955] [<c013708c>] (__warn) from [<c0137164>] (warn_slowpath_null+0x20/0x28)
[  141.836902] [<c0137164>] (warn_slowpath_null) from [<bf27784c>] (dwc3_stop_active_transfer.constprop.4+0xc4/0xe4 [dwc3])
[  141.848329] [<bf27784c>] (dwc3_stop_active_transfer.constprop.4 [dwc3]) from [<bf27ab14>] (__dwc3_gadget_ep_disable+0x64/0x528 [dwc3])
[  141.861034] [<bf27ab14>] (__dwc3_gadget_ep_disable [dwc3]) from [<bf27c27c>] (dwc3_gadget_ep_disable+0x3c/0xc8 [dwc3])
[  141.872280] [<bf27c27c>] (dwc3_gadget_ep_disable [dwc3]) from [<bf23b428>] (usb_ep_disable+0x11c/0x18c [udc_core])
[  141.883160] [<bf23b428>] (usb_ep_disable [udc_core]) from [<bf342774>] (disable_ep+0x18/0x54 [usb_f_ss_lb])
[  141.893408] [<bf342774>] (disable_ep [usb_f_ss_lb]) from [<bf3437b0>] (disable_endpoints+0x18/0x50 [usb_f_ss_lb])
[  141.904168] [<bf3437b0>] (disable_endpoints [usb_f_ss_lb]) from [<bf343814>] (disable_source_sink+0x2c/0x34 [usb_f_ss_lb])
[  141.915771] [<bf343814>] (disable_source_sink [usb_f_ss_lb]) from [<bf329a9c>] (reset_config+0x48/0x7c [libcomposite])
[  141.927012] [<bf329a9c>] (reset_config [libcomposite]) from [<bf329afc>] (composite_disconnect+0x2c/0x54 [libcomposite])
[  141.938444] [<bf329afc>] (composite_disconnect [libcomposite]) from [<bf23d7dc>] (usb_gadget_udc_reset+0x10/0x34 [udc_core])
[  141.950237] [<bf23d7dc>] (usb_gadget_udc_reset [udc_core]) from [<bf276d70>] (dwc3_gadget_reset_interrupt+0x64/0x698 [dwc3])
[  141.962022] [<bf276d70>] (dwc3_gadget_reset_interrupt [dwc3]) from [<bf27952c>] (dwc3_thread_interrupt+0x618/0x1a3c [dwc3])
[  141.973723] [<bf27952c>] (dwc3_thread_interrupt [dwc3]) from [<c01a7ce8>] (irq_thread_fn+0x1c/0x54)
[  141.983215] [<c01a7ce8>] (irq_thread_fn) from [<c01a7fbc>] (irq_thread+0x120/0x1f0)
[  141.991247] [<c01a7fbc>] (irq_thread) from [<c015ba14>] (kthread+0xf8/0x138)
[  141.998641] [<c015ba14>] (kthread) from [<c01078f0>] (ret_from_fork+0x14/0x24)
[  142.006213] ---[ end trace b4ecfe9f175b9a9c ]---

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-03-06 16:56:08 +02:00
Franck Demathieu 73561128eb usb: dwc3: Fix incorrect type for utmi mode
The utmi mode is unsigned according the dt-bindings.
Fix sparse issue (-Wtypesign):

  drivers/usb/dwc3/dwc3-omap.c:391:50: warning: incorrect type in argument 3 (different signedness)
  drivers/usb/dwc3/dwc3-omap.c:391:50:    expected unsigned int [usertype] *out_value
  drivers/usb/dwc3/dwc3-omap.c:391:50:    got int *<noident>

Signed-off-by: Franck Demathieu <fdemathieu@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-03-06 16:47:10 +02:00
Felipe Balbi cf3113d893 usb: dwc3: gadget: properly increment dequeue pointer on ep_dequeue
If request was already started, this means we had to
stop the transfer. With that we also need to ignore
all TRBs used by the request, however TRBs can only
be modified after completion of END_TRANSFER
command. So what we have to do here is wait for
END_TRANSFER completion and only after that jump
over TRBs by clearing HWO and incrementing dequeue
pointer.

Note that we have 2 possible types of transfers
here:

i) Linear buffer request
ii) SG-list based request

SG-list based requests will have r->num_pending_sgs
set to a valid number (> 0). Linear requests,
normally use a single TRB.

For each of these two cases, if r->unaligned flag is
set, one extra TRB has been used to align transfer
size to wMaxPacketSize.

All of these cases need to be taken into
consideration so we don't mess up our TRB ring
pointers.

Tested-by: Janusz Dziedzic <januszx.dziedzic@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-03-06 10:09:37 +02:00
Felipe Balbi 7369090a9f usb: dwc3: gadget: make Set Endpoint Configuration macros safe
Some gadget drivers are bad, bad boys. We notice
that ADB was passing bad Burst Size which caused top
bits of param0 to be overwritten which confused DWC3
when running this command.

In order to avoid future issues, we're going to make
sure values passed by macros are always safe for the
controller. Note that ADB still needs a fix to *not*
pass bad values.

Cc: <stable@vger.kernel.org> # v3.2+
Reported-by: Mohamed Abbas <mohamed.abbas@intel.com>
Sugested-by: Adam Andruszak <adam.andruszak@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-03-06 10:09:37 +02:00
Greg Kroah-Hartman bc46e23c34 USB: changes for v4.11
Here's the big pull request for the Gadget
 API. Again the majority of changes sit in dwc2
 driver. Most important changes contain a workaround
 for GOTGCTL being wrong, a sleep-inside-spinlock fix
 and the big series of cleanups on dwc2.
 
 One important thing on dwc3 is that we don't anymore
 need gadget drivers to cope with unaligned OUT
 transfers for us. We have support for appending one
 extra chained TRB to align transfer ourselves.
 
 Apart from these, the usual set of typos,
 non-critical fixes, etc.
 -----BEGIN PGP SIGNATURE-----
 
 iQJRBAABCAA7FiEElLzh7wn96CXwjh2IzL64meEamQYFAliKBd0dHGZlbGlwZS5i
 YWxiaUBsaW51eC5pbnRlbC5jb20ACgkQzL64meEamQb1Yw//XEI0VeUdsRM/JKK5
 4BBoFCCUXT7jZMyzm7x9G7/4Tz3Xn9I9elAbZ7A3ctpLQXVO0KUAc5S3MRmq1ghj
 8h18ZrOLqWG6gG+0eOtzSQLJ91+ULV+nyV6jS+RJyio7AMKy6XW0hRHQQs8ggcqg
 A/hZKVI/GdvnoSSLVNoWFxTiVC7Pu62IsWJV6BJuWubEze7u97xfBIt3qB9h2R8q
 ARfy29LYZulgrRYZ2DAtrKNFC8yKdIiKxWcmI47FHcNXtnQ6yAu7VqFcKWlH9Jvb
 NY/YAzv30leOXHrwHVXCM/Urh7SK6FJIIdgoDMpCWoy1CK2pHXkJCndt/NuM721h
 DYaopfNBJLtjvYDsvtnGXo3DC6+hBd3oYEz+gogGS/5gocr2ChnRK8Qc5T8eXYnC
 OBIVKeHcsx9wMxYwwxk2axWjflfbSRjPnpZHibgkvdrwGVY+Hcwf5GyixvTdqQJM
 dMrZcIPqtPJAg7OBPoH0LEViT14+lc8f5n6D0T/NezLxeeZvbcWQ5p17LpNal5oi
 S+4kmtNWR7nXKSdICvc00Ap+Iqu91eB4c1MfvP6HSLq7wpjs5QhWtDvM7++ygjL1
 7m3ExmXUx+j29M64WM9KTNlXZFkQ8XB5PzmcXueQkz9fd2u8JJhBqGHdVWFHOv9y
 4YGdaSpeqsui9bFoIdbjn0EO3+g=
 =gk8j
 -----END PGP SIGNATURE-----

Merge tag 'usb-for-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next

Felipe writes:

USB: changes for v4.11

Here's the big pull request for the Gadget
API. Again the majority of changes sit in dwc2
driver. Most important changes contain a workaround
for GOTGCTL being wrong, a sleep-inside-spinlock fix
and the big series of cleanups on dwc2.

One important thing on dwc3 is that we don't anymore
need gadget drivers to cope with unaligned OUT
transfers for us. We have support for appending one
extra chained TRB to align transfer ourselves.

Apart from these, the usual set of typos,
non-critical fixes, etc.
2017-01-26 15:36:28 +01:00
Felipe Balbi e42a5dbb8a usb: dwc3: host: pass quirk-broken-port-ped property for known broken revisions
dwc3 revisions <=3.00a have a limitation where Port Disable command
doesn't work. Set the quirk-broken-port-ped property for such
controllers so XHCI core can do the necessary workaround.

[rogerq@ti.com] Updated code from platform data to device property.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-26 11:17:37 +02:00
Felipe Balbi 2878178905 usb: dwc3: gadget: read IN ep FIFO size from HW
Instead of assuming all IN endpoints support 1024
bytes, let's read the actual value from HW and pass
that to gadget API.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-25 12:49:00 +02:00
Felipe Balbi ffb80fc672 usb: dwc3: gadget: skip Set/Clear Halt when invalid
At least macOS seems to be sending
ClearFeature(ENDPOINT_HALT) to endpoints which
aren't Halted. This makes DWC3's CLEARSTALL command
time out which causes several issues for the driver.

Instead, let's just return 0 and bail out early.

Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-24 11:04:16 +02:00
Baolin Wang 538967983b usb: dwc3: ep0: Fix the possible missed request for handling delay STATUS phase
When handing the SETUP packet by composite_setup(), we will release the
dwc->lock. If we get the 'USB_GADGET_DELAYED_STATUS' result from setup
function, which means we need to delay handling the STATUS phase.

But during the lock release period, maybe the request for handling delay
STATUS phase has been queued into list before we set 'dwc->delayed_status'
flag or entering 'EP0_STATUS_PHASE' phase, then we will miss the chance
to handle the STATUS phase. Thus we should check if the request for delay
STATUS phase has been enqueued when entering 'EP0_STATUS_PHASE' phase in
dwc3_ep0_xfernotready(), if so, we should handle it.

Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-24 11:04:15 +02:00
Chanwoo Choi c773bb0b92 usb: dwc3: omap: Replace the extcon API
This patch uses the resource-managed extcon API for extcon_register_notifier()
and replaces the deprecated extcon API as following:
- extcon_get_cable_state_() -> extcon_get_state()

Cc: linux-omap@vger.kernel.org
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-24 11:04:15 +02:00
Felipe Balbi c6267a5163 usb: dwc3: gadget: align transfers to wMaxPacketSize
Instead of passing quirk_ep_out_aligned_size, we can use one extra TRB
to align transfer to wMaxPacketSize.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-24 11:04:13 +02:00
Felipe Balbi 905dc04ea7 usb: dwc3: gadget: allocate bounce buffer for unaligned xfers
Allocate a coherent buffer of 1024 bytes (size of a single superspeed
bulk packet) to serve as bounce buffer for an extra TRB needed to align
transfers to wMaxPacketSize.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-24 11:04:12 +02:00
Felipe Balbi e49d3cf492 usb: dwc3: gadget: extract __dwc3_prepare_one_trb()
This new internal function will be used to solve a minor issue with dwc3
which exists in regards to short packets with OUT endpoints. Currently
we're asking gadget driver to *always* send us aligned requests; however
if we have enough TRBs we can easily append one extra TRB chained to the
previous and keep a throw away 1024 byte buffer around for that.

The actual fix will come in a separate patch, this is merely in
preparation for such fix.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-24 11:04:12 +02:00
Felipe Balbi 843053093f usb: dwc3: gadget: simplify dwc3_prepare_one_trb()
We are already passing struct dwc3_request * to dwc3_prepare_one_trb(),
because of that there's no need to extract dma address and length in the
caller. We can let dwc3_prepare_one_trb() itself handle that part.

This simplifies the prototype of the function by removing two arguments.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-24 11:04:12 +02:00
Javier Martinez Canillas 0e4018ff5d usb: dwc3: exynos: Remove MODULE_ALIAS()
Exynos is DT-only, so there's no need for a platform MODALIAS.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-24 11:04:10 +02:00
Shuah Khan 3e27b3f66a usb: dwc3: exynos remove suspend clock unspecified debug message
dwc3-exynos prints debug message when suspend clock is not specified.
The suspend clock is optional and driver can work without it.

This debug message doesn't add any value and leads to confusion and
concern. Remove it.

Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-24 11:04:09 +02:00
Shuah Khan 8ae584d195 usb: dwc3: exynos fix axius clock error path to do cleanup
Axius clock error path returns without disabling clock and suspend clock.
Fix it to disable them before returning error.

Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-12 10:03:59 +02:00
Roger Quadros 9418ee15f7 usb: dwc3: gadget: Fix full speed mode
DCFG.DEVSPD == 0x3 is not valid and we need to set
DCFG.DEVSPD to 0x1 for full speed mode. Same goes for
DSTS.CONNECTSPD.

Old databooks had 0x3 for full speed in 48MHz mode for
USB1.1 transceivers which was never supported. Newer databooks
don't mention 0x3 at all.

Cc: John Youn <John.Youn@synopsys.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-03 14:33:48 +02:00
Heikki Krogerus 8f8983a568 usb: dwc3: pci: add Intel Gemini Lake PCI ID
Intel Gemini Lake SoC has the same DWC3 than Broxton. Add
the new ID to the supported Devices.

Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-02 10:55:28 +02:00
John Youn 0eae2fde16 usb: dwc3: pci: Add "linux,sysdev_is_parent" property
Calling platform_device_add_properties() replaces existing properties so
the "linux,sysdev_is_parent" property doesn't get set. Add this property
to each platform.

Fixes: d64ff406e5 ("usb: dwc3: use bus->sysdev for DMA configuration")
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-02 10:55:28 +02:00
Grygorii Strashko 12a7f17fac usb: dwc3: omap: fix race of pm runtime with irq handler in probe
Now races can happen between interrupt handler execution and PM runtime in
error handling code path in probe and in dwc3_omap_remove() which will lead
to system crash:

in probe:
...
 err1:
	pm_runtime_put_sync(dev);
^^ PM runtime can race with IRQ handler when deferred probing happening
   due to extcon
	pm_runtime_disable(dev);

	return ret;

in dwc3_omap_remove:
...
	dwc3_omap_disable_irqs(omap);
^^ IRQs are disabled in HW, but handler may still run
	of_platform_depopulate(omap->dev);
	pm_runtime_put_sync(&pdev->dev);
^^ PM runtime can race with IRQ handler
	pm_runtime_disable(&pdev->dev);

	return 0;

So, OMAP DWC3 IRQ need to be disabled before calling
pm_runtime_put() in probe and in dwc3_omap_remove().

Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-02 10:55:28 +02:00
Janusz Dziedzic d7fd41c6db usb: dwc3: skip interrupt when ep disabled
In case EP disabled pass only EPCPLT command
to be handled. In other case we could hit
Bug like below.

BUG: unable to handle kernel NULL pointer dereference at 0000000000000003
IP:
[<ffffffff81673428>] dwc3_thread_interrupt+0x11c8/0x1790

while dep->endpoint.desc is NULL.

Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-02 10:55:28 +02:00
Hans de Goede 51c1685d95 usb: dwc3: pci: Fix dr_mode misspelling
usb_get_dr_mode() expects the device-property to be spelled
"dr_mode" not "dr-mode".

Spelling it properly fixes the following warning showing up in dmesg:
[ 8704.500545] dwc3 dwc3.2.auto: Configuration mismatch. dr_mode forced to gadget

Signed-off-by: Hans de Goede <hdegoede@redhat.com
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-02 10:55:28 +02:00
Felipe Balbi e71d363d9c usb: dwc3: core: avoid Overflow events
Now that we're handling so many transfers at a time
and for some dwc3 revisions LPM events *must* be
enabled, we can fall into a situation where too many
events fire and we start receiving Overflow events.

Let's do what XHCI does and allocate a full page for
the Event Ring, this will avoid any future issues.

Cc: <stable@vger.kernel.org> # v4.9
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-02 10:55:28 +02:00
Felipe Balbi d621459299 usb: dwc3: gadget: always unmap EP0 requests
commit 0416e494ce ("usb: dwc3: ep0: correct cache
sync issue in case of ep0_bounced") introduced a bug
where we would leak DMA resources which would cause
us to starve the system of them resulting in failing
DMA transfers.

Fix the bug by making sure that we always unmap EP0
requests since those are *always* mapped.

Fixes: 0416e494ce ("usb: dwc3: ep0: correct cache
	sync issue in case of ep0_bounced")
Cc: <stable@vger.kernel.org>
Tested-by: Tomasz Medrek <tomaszx.medrek@intel.com>
Reported-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-02 10:55:28 +02:00
Felipe Balbi 19ec31230e usb: dwc3: ep0: explicitly call dwc3_ep0_prepare_one_trb()
Let's call dwc3_ep0_prepare_one_trb() explicitly
because there are occasions where we will need more
than one TRB to handle an EP0 transfer.

A follow-up patch will fix one bug related to
multiple-TRB Data Phases when it comes to
mapping/unmapping requests for DMA.

Cc: <stable@vger.kernel.org>
Reported-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-02 10:55:28 +02:00
Felipe Balbi 7931ec86c1 usb: dwc3: ep0: add dwc3_ep0_prepare_one_trb()
For now this is just a cleanup patch, no functional
changes. We will be using the new function to fix a
bug introduced long ago by commit 0416e494ce
("usb: dwc3: ep0: correct cache sync issue in case
of ep0_bounced") and further worsened by commit
c0bd5456a4 ("usb: dwc3: ep0: handle non maxpacket
aligned transfers > 512")

Cc: <stable@vger.kernel.org>
Reported-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-01-02 10:55:28 +02:00
Linus Torvalds a9042defa2 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial updates from Jiri Kosina.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
  NTB: correct ntb_spad_count comment typo
  misc: ibmasm: fix typo in error message
  Remove references to dead make variable LINUX_INCLUDE
  Remove last traces of ikconfig.h
  treewide: Fix printk() message errors
  Documentation/device-mapper: s/getsize/getsz/
2016-12-14 11:12:25 -08:00
Masanari Iida 9165dabb25 treewide: Fix printk() message errors
This patch fix spelling typos in printk and kconfig.

Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2016-12-14 10:54:27 +01:00
Greg Kroah-Hartman ae4d814bf1 usb: patches for v4.10 merge window
One big merge this time with a total of 166 non-merge commits.
 
 Most of the work, by far, is on dwc2 this time (68.2%) with dwc3 a far
 second (22.5%). The remaining 9.3% are scattered on gadget drivers.
 
 The most important changes for dwc2 are the peripheral side DMA support
 implemented by Synopsys folks and support for the new IOT dwc2
 compatible core from Synopsys.
 
 In dwc3 land we have support for high-bandwidth, high-speed isochronous
 endpoints and some non-critical fixes for large scatter lists.
 
 Apart from these, we have our usual set of cleanups, non-critical fixes,
 etc.
 -----BEGIN PGP SIGNATURE-----
 
 iQJRBAABCAA7FiEElLzh7wn96CXwjh2IzL64meEamQYFAlgu7+gdHGZlbGlwZS5i
 YWxiaUBsaW51eC5pbnRlbC5jb20ACgkQzL64meEamQaDbxAAsgDPAp8QTx8D1d70
 hSGyPZ55rmqlzBNbUUOQyk/AeN5xM3XVbjZNOxWn4c386iaDrngcqOrxjCbBRsje
 b9yMESMiZsTPVlKXE45yXt//NHg1KUfpHON7rybaiFq0uqjUhnQf95DeYPgJVxit
 7F9B+05XcNMyxYRoz6bGkRTU+lcJ6g3/orgKfp4t/hs8WUNXH6+71keMF+IdLYNH
 mcPmJ8MXpfLzv8eweRwV0s/3flxCuFx1ksZ8cW6qHR5vX303X2sGTlinBmhfQapr
 t0a+OBtLpZdNmjw/yB2odc/1jjLNRHpYU5xGqwouMx9Ca2PocFT2xFbmUWR23xp1
 X0rkICRxcLPjZql2Uld5QHO9dPnF/FbX0Njuvxo+2r8ENE5/eG4C/RcYcRDmYPsu
 u8k2rKFs0+yCOAU91rD8mayJVBWBJ4trqZFT0TcocCGsMTk8fTYpF1Iskj9Z4FKz
 yo+lgyCCtp673ykGZ1ezsL6YWOmdrQv/PurKZqrXAmdhi6+mImLI/nAHtAdOZx0X
 zK9MwPnwDxrPiqhrZ46+Bm/EjZI50TM44M1ldmCwKi/6/Nvy54DHMtjPI5/9205R
 bjftW3DkVWAC//29RNcGEHtwiJFPEU/kdoRFOPhKGJ7ocCzFVSTFBgo02kDsC6De
 Wouv2QTFuZN9s17o29YVD3bGJZM=
 =5WN9
 -----END PGP SIGNATURE-----

Merge tag 'usb-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next

Felipe writes:

usb: patches for v4.10 merge window

One big merge this time with a total of 166 non-merge commits.

Most of the work, by far, is on dwc2 this time (68.2%) with dwc3 a far
second (22.5%). The remaining 9.3% are scattered on gadget drivers.

The most important changes for dwc2 are the peripheral side DMA support
implemented by Synopsys folks and support for the new IOT dwc2
compatible core from Synopsys.

In dwc3 land we have support for high-bandwidth, high-speed isochronous
endpoints and some non-critical fixes for large scatter lists.

Apart from these, we have our usual set of cleanups, non-critical fixes,
etc.
2016-11-18 16:02:15 +01:00
Arnd Bergmann 8c9f2de459 usb: dwc3: Do not set dma coherent mask
The dma mask is correctly set up by the DT probe function, no
need to override it any more.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18 13:54:55 +02:00
Arnd Bergmann d64ff406e5 usb: dwc3: use bus->sysdev for DMA configuration
The dma ops for dwc3 devices are not set properly. So, use a
physical device sysdev, which will be inherited from parent,
to set the hardware / firmware parameters like dma.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Tested-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18 13:54:54 +02:00
Arnd Bergmann 1c404b51a0 usb: dwc3: ep0: avoid empty-body warning
Building with W=1, we get a warning about harmless empty statements:

drivers/usb/dwc3/ep0.c: In function 'dwc3_ep0_handle_intf':
drivers/usb/dwc3/ep0.c:491:4: error: suggest braces around empty body in an 'if' statement [-Werror=empty-body]

Instead of adding empty braces which would introduce checkpatch.pl
warnings, we're just removing the code which doesn't do anything and
making sure we return 0 so USBCV tool is happy.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18 13:54:54 +02:00
Felipe Balbi 36daf3aa39 usb: dwc3: pci: avoid build warning
dwc3_pci_dsm() is only needed if (PM || PM_SLEEP),
we should make sure it's not defined if neither of
those is defined.

This fixes a randconfig build warning.

Acked-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18 13:54:52 +02:00
John Youn 28632b44d1 usb: dwc3: Workaround for irq mask issue
This is a workaround for STAR 9000961433 which affects only version
3.00a of the DWC_usb3 core. This prevents the controller interrupt from
being masked while handling events. Enabling interrupt moderation allows
us to work around this issue because once the GEVNTCOUNT.count is
written the IRQ is immediately deasserted and won't be asserted again
until GEVNTCOUNT.EHB is cleared.

Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18 13:54:51 +02:00
John Youn cf40b86b6e usb: dwc3: Implement interrupt moderation
Implement interrupt moderation which allows the interrupt rate to be
throttled. To enable this feature the dwc->imod_interval must be set to
1 or greater. This value specifies the minimum inter-interrupt interval,
in 250 ns increments. A value of 0 disables interrupt moderation.

This applies for DWC_usb3 version 3.00a and higher and for DWC_usb31
version 1.20a and higher.

Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18 13:54:51 +02:00
John Youn 65aca32050 usb: dwc3: gadget: clear events in top-half handler
Now that all the infrastructure is in place, we can
clear events in the top-half handler in order to
bring IRQ line low ASAP.

This is also a necessary step in order to implement
workaround for known erratum in follow-up patches.

Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18 13:54:43 +02:00
John Youn ebbb2d5939 usb: dwc3: gadget: use evt->cache for processing events
Let's start copying events from evt->buf to
evt->cache and use evt->cache for processing events.

A follow-up patch will be added to clear events in
the top-half handler in order to bring IRQ line low
as soon as possible.

Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18 13:54:43 +02:00
Felipe Balbi caefe6c7be usb: dwc3: gadget: use evt->length as we should
Instead of always accessing the macro directly,
let's rely on evt->length which is the actual length
of current event buffer. While unlikely, we could
change event buffer's size at any time.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18 13:54:43 +02:00
John Youn d9fa4c63f7 usb: dwc3: core: add a event buffer cache
This extra buffer will be used so we can copy
triggered events from our event buffer to this cache
and process all of them later in bottom half
handler.

We need this in order to implement a workaround for
a known erratum in recent DWC3 release.

Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18 13:54:42 +02:00
Felipe Balbi a22f884b26 usb: dwc3: core: remove dwc3_soft_reset()
dwc3_soft_reset() is doing the same thing as
dwc3_core_soft_reset(). Let's remove
dwc3_soft_reset() since that's not needed anymore.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18 13:54:42 +02:00
John Youn 7ac51a12ea usb: dwc3: Add a function to check properties
Add a function to check properties and call it from probe. This will
allow us to add check code without bloating the probe function. This
needs to be done after dwc3_get_properties() and dwc3_core_init() so
that all the properties and hardware configs are available.

Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18 13:54:33 +02:00
John Youn a987a906e9 usb: dwc3: Add a check for the DWC_usb3 core
Add a helper function to check if we are running on a DWC_usb3 core.

Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18 13:54:20 +02:00
John Youn 5fb6fdaf38 usb: dwc3: gadget: Fix dead code writing GCTL.RAMCLKSEL
The register programming code in dwc2_updated_ram_clk_sel() will never
be executed. And in fact the entire function can be removed as there is
no way to override the default value of GCTL.RAMCLKSEL. Remove the
function and add a comment explaining where GCTL.RAMCLKSEL should be
programmed if needed in the future.

This fixes dead code warnings in coverity.

Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18 13:54:17 +02:00
John Youn 39ebb05ca8 usb: dwc3: gadget: Remove descriptor arguments to ep_enable
The __dwc3_gadget_endpoint_enable() function has access to the endpoint
descriptors via the usb_ep. So we don't need to pass them in as
arguments. The descriptors should be set by the caller prior to calling
usb_ep_enable().

Signed-off-by: John Youn <johnyoun@synopsys.com>

[felipe.balbi@linux.intel.com : minor improvements]

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18 13:54:16 +02:00
Janusz Dziedzic f2694a93e0 usb: dwc3: warn on once when no trbs
Seems last time we hit few issues where
we get trb_left = 0, mainly because of
HWO bit still set in previous TRB.
Add warn on once to catch/fix such
problems much faster.

Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18 13:54:15 +02:00
Janusz Dziedzic 87aba10639 usb: dwc3: isoc clean DWC3_EP_PENDING_REQUEST flag
After we kick_transfer we should clean
DWC3_EP_PENDING_REQUEST endpoint flag.

Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18 13:54:15 +02:00
Janusz Dziedzic e3aee48692 usb: dwc3: fix post-increment
Use pre-increment and set -ETIMEDOUT correctly.

Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18 13:54:14 +02:00
Janusz Dziedzic ce3fc8b329 usb: dwc3: clean TRB if STARTTRANSFER fail
In case STARTTRANSFER will fail, clean TRB.
Seems HW in such case don't clean HWO bit.
So, without this cleanup prev_trb still have
HWO bit set.

In my case (without patch), after first START failed:
- dep->enqueue == 1
- dep->dequeue == 1
- prev_trb still have HWO set
- left_trb() == 0
No way to send more data.

Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18 13:54:14 +02:00
Janusz Dziedzic 8ab89da4c2 usb: dwc3: decrement queued_requests
In case we will fail to STARTTRANSFER we should
also decrement queued_requests.

Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-18 13:54:14 +02:00
Felipe Balbi 5eb30cedce usb: dwc3: trace: purge dwc3_trace()
Finally get rid of dwc3_trace() hack. If any other
message is truly needed, we should add proper
tracepoints for them instead of hacking around with
dwc3_trace() or similar.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-08 12:52:13 +02:00
Felipe Balbi 2870e5013e usb: dwc3: trace: add a tracepoint for ep enable/disable
instead of using a simple trace_printk() wrapper,
let's add an actual tracepoint and print further
details about the endpoint being operated upon.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-08 12:52:12 +02:00
Felipe Balbi 9cecca75b5 usb: dwc3: pci: call _DSM for suspend/resume
Intel's BXT devices need to execute a _DSM method
during {runtime_,}{suspend,resume} in order to get a
chunk of dwc3 to power gate and save some extra
power.

Let's do that now.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-03 10:38:42 +02:00
Felipe Balbi 0f817ae696 usb: dwc3: pci: add a private driver structure
We'll be tracking a little more information for PCI
drivers, it's about time we add a private structure
for that.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-03 10:38:41 +02:00
Felipe Balbi ff377ae47d usb: dwc3: gadget: always kick if num_pending_sgs > 0
When we get a half-way processed request, we should
make sure to try to prepare further TRBs for it or
for any possibly queued up request held in our
pending_list. This will make sure our controller is
kept busy for as long as possible.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-03 10:38:41 +02:00
Felipe Balbi 7282c4ef0b usb: dwc3: gadget: stop touching HWO TRBs
Say we have three requests prepared to the HW (reqA,
reqB, and reqC). All of them are composed of
SG-lists with several entries and they all requests
interrupt only on last TRBs of the SG-list.

When we get interrupt for reqA, it could be that
reqB is already half-way transferred and some of its
TRBs will have HWO already cleared.

It's okay to free up TRBs without HWO bit set, but
we need to guarantee we don't giveback a request
that's half-way transferred as that will confuse
gadget drivers.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-03 10:38:41 +02:00
Felipe Balbi d86c5a676e usb: dwc3: gadget: always try to prepare on started_list first
In cases where we're given an SG-list which is
longer than the amount of currently available TRBs,
we will be left with the same request on
started_list and we should prioritize that request
over possible new requests on pending_list. That's
a way to guarantee requests complete in order.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-03 10:38:40 +02:00
Felipe Balbi e62c5bc573 usb: dwc3: gadget: tracking per-TRB remaining bytes
This will give us a simpler way of figuring out how
many bytes were left in each TRB. It's useful for
cases where we queue only part of an SG-list due to
amount of available TRBs at the time of kicking the
transfer.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-03 10:38:40 +02:00
Felipe Balbi 6cb2e4e3de usb: dwc3: gadget: cope with XferNotReady before usb_ep_queue()
If XferNotReady comes before usb_ep_queue() we will
set our PENDING request flag and wait for a
request. However, originally, we were assuming
usb_ep_queue() would always happen before our first
XferNotReady and that causes a corner case where we
could try to issue ENDTRANSFER command before
STARTTRANSFER.

Let's fix that by tracking endpoints which have been
started.

Reported-by: Janusz Dziedzic <januszx.dziedzic@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-03 10:38:40 +02:00
Baolin Wang 76a638f8ac usb: dwc3: gadget: wait for End Transfer to complete
Instead of just delaying for 100us, we should
actually wait for End Transfer Command Complete
interrupt before moving on. Note that this should
only be done if we're dealing with one of the core
revisions that actually require the interrupt before
moving on.

[ felipe.balbi@linux.intel.com: minor improvements ]

Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-03 10:38:39 +02:00
Masahiro Yamada 785c91f8ae usb: dwc3: cleanup with list_first_entry_or_null()
The combo of list_empty() check and return list_first_entry()
can be replaced with list_first_entry_or_null().

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-03 10:38:37 +02:00
Baolin Wang bb01473648 usb: dwc3: gadget: don't clear RUN/STOP when it's invalid to do so
When we change the USB function with configfs dynamically, we possibly
met this situation: one core is doing the control transfer, another core
is trying to unregister the USB gadget from userspace, we must wait for
completing this control tranfer, or it will hang the controller to set
the DEVCTRLHLT flag.

[ felipe.balbi@linux.intel.com: several fixes to the patch
	- call complete() before starting following SETUP transfer
	- add a macro for ep0_in_setup's timeout
	- change commit subject slightly
	- break lines at 72 characters (git adds an 8-character tab)
	- avoid changes to dwc3_gadget_run_stop() ]

Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-03 10:38:35 +02:00
Felipe Balbi cf68923055 usb: dwc3: gadget: purge dwc3_stop_active_transfers()
That function is unnecessarily called from
dwc3_gadget_reset_interrupt(). Gadget drivers (and
thus, functions) are required to dequeue all pending
requests when they get notified about a USB Bus
Reset.

Trying to make sure there are no pending requests
only serves the purpose of working around possibly
bad gadgets.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-03 10:38:35 +02:00
Felipe Balbi c5ac6116db usb: dwc3: core: add dwc3_get_properties()
This helper will be responsible for reading and
parsing our properties. No functional changes in
this patch, cleanup only.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-03 10:38:35 +02:00
Felipe Balbi 3b2733227f usb: dwc3: core: remove unnecessary alignment
Kernel will give us page aligned memory anyway.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-03 10:38:34 +02:00
Felipe Balbi 941f918ecf usb: dwc3: core: introduce dwc3_core_setup_global_control()
This little helper will be used to setup anything
related to GCTL register. There are no functional
changes, this is a cleanup only patch.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-03 10:38:34 +02:00
Felipe Balbi 0759956f8a usb: dwc3: core: introduce dwc3_core_is_valid()
This little helper will be used to make sure we're
dealing with a valid Synopsys DWC3 or DWC3.1 core.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-03 10:38:34 +02:00
John Youn 0bb39ca1ad usb: dwc3: Add support for device L1 exit
For the usb31 IP and from version 2.90a of the usb3 IP, the core
supports HW exit from L1 in HS. Enable it, otherwise the controller may
never exit from LPM to do a transfer.

Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-03 10:38:33 +02:00
Lu Baolu f9d2f9228c usb: dwc3: remove unused struct member dwc3->mem
Member @mem in struct dwc3 is not used in any places. Clean up it.

Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-03 10:38:33 +02:00
Felipe Balbi 0a695d4c75 usb: dwc3: gadget: never ever kill the machine
We should never kill the machine just because some
USB endpoint type is wrong. WARN about it and move
on.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-03 10:38:32 +02:00
Felipe Balbi c9508c8c50 usb: dwc3: gadget: only interrupt on short if short_not_ok is set
We don't need to know about short packets unless
gadget driver told us it's not ok to see them on the
bus. In the normal situation we can continue
processing the list of requests if we get a Short
packet.

Also, note that we're making sure ISP is only set
for OUT endpoints, where that setting is valid.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-03 10:38:32 +02:00
Felipe Balbi 58f29034b4 usb: dwc3: gadget: CSP is only valid for OUT endpoints
CSP bit is only valid for OUT endpoints. Synopsys
databook is unclear if HW ignores CSP for IN
endpoints (chances are, it does) but to avoid
problems, let's make sure to set CSP only when valid
to do so.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-03 10:38:32 +02:00
Felipe Balbi b9bd138e06 usb: dwc3: gadget: remove unused 'first_trb_index'
Recent changes have turned this field obsolete. Remove it.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-03 10:38:31 +02:00
Felipe Balbi 39e07ffb1c usb: dwc3: ep0: simplify dwc3_ep0_handle_feature()
By extracting smaller functions from
dwc3_ep0_handle_feature(), it becomes far easier to
understand what's going on. Cleanup only, no
functional changes.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-03 10:38:31 +02:00
Felipe Balbi 6d729a55cc usb: dwc3: host: extract dwc3_host_get_irq()
Cleanup only, no functional changes.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-03 10:38:31 +02:00
Felipe Balbi 6db3812e09 usb: dwc3: gadget: extract dwc3_gadget_get_irq()
Cleanup only, no functional changes.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-03 10:38:30 +02:00
Felipe Balbi 4dd5a69e49 usb: dwc3: trace: add a proper tracepoint for reg accessors
We want to reduce the usage of dwc3_trace() in favor
of proper tracepoints which can be enabled/disabled
by the user. Let's start with our register
accessors.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-03 10:38:30 +02:00
Felipe Balbi ba1773fb7d usb: dwc3: Kconfig: allow all glues to build if COMPILE_TEST
We shouldn't have any glue layer which doesn't
compile everywhere. In order to make sure this is
always the case, make sure COMPILE_TEST is properly
added at dependency list of a config entry.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-03 10:38:30 +02:00
Felipe Balbi 57b14da562 usb: dwc3: don't compile dwc3_trace() unless CONFIG_FTRACE=y
We don't need dwc3_trace() unless we're building a
kernel with CONFIG_FTRACE. This patch reduces
dwc3.ko text size a bit while also removing overhead
of dwc3_trace() calls.

   text    data     bss     dec     hex filename
  50796     581       0   51377    c8b1 drivers/usb/dwc3/dwc3.o
  43961     581       0   44542    adfe drivers/usb/dwc3/dwc3.o.patched

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-03 10:38:29 +02:00
Felipe Balbi a97ea99460 usb: dwc3: gadget: offset Start Transfer latency for bulk EPs
We can offset the latency of a full Start Transfer
command - where we _must_ poll for its completion -
to usb_ep_enable() time. This means that once
requests start showing up from the gadget driver, we
can rely on No Response Update Transfer command -
where we don't need to poll for completion.

This patch, starts implementing this method for Bulk
endpoints, even though, technically, we could extend
it to all other endpoints in future commits.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-03 10:38:29 +02:00
Felipe Balbi fa8d965d73 usb: dwc3: trace: pretty print high-bandwidth transfers too
In case of periodic transfers, let's pretty print
the size field as a multiplier followed by length,
such as :

	3x 1024

instead of:

	33555456

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-11-03 10:38:28 +02:00
Felipe Balbi 43c96be1c4 usb: dwc3: trace: print out ep0state also from XferComplete
With this extra piece of information, it will be
easier to find mismatches between driver and HW.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-10-31 11:17:34 +02:00
Felipe Balbi cdd72ac20b usb: dwc3: debug: move dwc3_ep0_state_string() to debug.h
We will be using dwc3_ep0_state_string() from within
our tracepoints, so we need to move that helper to
debug.h in order for it to be accessible.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-10-31 11:17:34 +02:00
Felipe Balbi 8566cd1adf usb: dwc3: gadget: remove redundant trace prints
Removing some trace prints which were made redundant
when we started decoding events and TRBs completely
within their respective trace points.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-10-31 11:15:36 +02:00
Felipe Balbi 45a2af2f2b usb: dwc3: debug: decode control endpoint phase too
DWC3 can tell us which phase of a setup transfer
we're getting into. Let's decode it from the event
to make it easier to debug.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-10-31 11:15:36 +02:00
Felipe Balbi 799e9dc829 usb: dwc3: gadget: conditionally disable Link State change events
Link State Change events are only needed for
debugging and to apply certain workarounds on known
errata. Let's save a few cycles by disabling these
events completely on working revisions of the core.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-10-31 11:15:35 +02:00
Felipe Balbi 15b8d9332b usb: dwc3: gadget: giveback request if we can't kick it
There might be situations where a Start Transfer
command might fail, if that ever happens, instead of
simply removing the request from our list, we should
give the request back to the gadget driver,
otherwise we might eventually starve it from requests.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-10-31 11:15:35 +02:00
Felipe Balbi 8897a761c3 usb: dwc3: gadget: make use of No Response Update Transfer
No Response Update Transfer is a special type of
Update Transfer command which can be used whenever
we're not relying on XferNotReady to prepare
transfers. With this, we don't need to wait for
CMDACT to be cleared and issue further commands to
the endpoint straight away.

Let's start using this version to skip the long-ish
wait.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-10-31 11:15:34 +02:00
Felipe Balbi 5999914f22 usb: dwc3: gadget: properly check ep cmd
The cmd argument we pass to
dwc3_send_gadget_ep_cmd() could contain extra
arguments embedded. When checking for StartTransfer
command, we need to make sure to match only lower 4
bits which contain the actual command and ignore the
rest.

Reported-by: Janusz Dziedzic <januszx.dziedzic@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-10-31 11:15:34 +02:00
Felipe Balbi 6b9018d4c1 usb: dwc3: gadget: set PCM1 field of isochronous-first TRBs
In case of High-Speed, High-Bandwidth endpoints, we
need to tell DWC3 that we have more than one packet
per interval. We do that by setting PCM1 field of
Isochronous-First TRB.

Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-10-31 11:15:34 +02:00
Felipe Balbi 4accb8a1ee usb: dwc3: st: add missing <linux/pinctrl/consumer.h> include
dwc3-st uses pinctrl_pm_select_*_state() however it
doesn't include the necessary header. Fix the build
break caused by that, by simply including the
missing header.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-10-31 11:14:27 +02:00
Vivek Gautam 9b9d7cdd0a usb: dwc3: Fix error handling for core init
Fixing the sequence of events in dwc3_core_init() error exit path.
dwc3_core_exit() call is also removed from the error path since,
whatever it's doing is already done.

Fixes: c499ff7 usb: dwc3: core: re-factor init and exit paths

Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Stable <stable@vger.kernel.org> # 4.8+
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-10-31 11:14:27 +02:00
Christophe JAILLET 51fbc7c06c usb: dwc3: Fix size used in dma_free_coherent()
In commit 2abd9d5fa6 ("usb: dwc3: ep0: Add chained TRB support"), the
size of the memory allocated with 'dma_alloc_coherent()' has been modified
but the corresponding calls to 'dma_free_coherent()' have not been updated
accordingly.

This has been spotted with coccinelle, using the following script:
////////////////////
@r@
expression x0, x1, y0, y1, z0, z1, t0, t1, ret;
@@

*   ret = dma_alloc_coherent(x0, y0, z0, t0);
    ...
*   dma_free_coherent(x1, y1, ret, t1);

@script:python@
y0 << r.y0;
y1 << r.y1;

@@
if y1.find(y0) == -1:
 print "WARNING: sizes look different:  '%s'   vs   '%s'" % (y0, y1)
////////////////////

Fixes: 2abd9d5fa6 ("usb: dwc3: ep0: Add chained TRB support")

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-10-17 12:35:48 +03:00
Felipe Balbi d889c23ce4 usb: dwc3: gadget: never pre-start Isochronous endpoints
We cannot pre-start isochronous endpoints because we
rely on the micro-frame number passed via
XferNotReady command for proper Isochronous
scheduling.

Fixes: 08a36b5438 ("usb: dwc3: gadget: simplify __dwc3_gadget_ep_queue()")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-10-17 11:14:00 +03:00
Felipe Balbi a9c3ca5fae usb: dwc3: gadget: properly account queued requests
Some requests could be accounted for multiple
times. Let's fix that so each and every requests is
accounted for only once.

Cc: <stable@vger.kernel.org> # v4.8
Fixes: 55a0237f8f ("usb: dwc3: gadget: use allocated/queued reqs for LST bit")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-10-17 11:14:00 +03:00
Greg Kroah-Hartman 8152263748 usb: patches for v4.9 merge window
This time around we have 92 non-merge commits. Most
 of the changes are in drivers/usb/gadget (40.3%)
 with drivers/usb/gadget/function being the most
 active directory (27.2%).
 
 As for UDC drivers, only dwc3 (26.5%) and dwc2
 (12.7%) have really been active.
 
 The most important changes for dwc3 are better
 support for scatterlist and, again, throughput
 improvements. While on dwc2 got some minor stability
 fixes related to soft reset and FIFO usage.
 
 Felipe Tonello has done some good work fixing up our
 f_midi gadget and Tal Shorer has implemented a nice
 API change for our ULPI bus.
 
 Apart from these, we have our usual set of
 non-critical fixes, spelling fixes, build warning
 fixes, etc.
 -----BEGIN PGP SIGNATURE-----
 
 iQI6BAABCAAkBQJX2TpXHRxmZWxpcGUuYmFsYmlAbGludXguaW50ZWwuY29tAAoJ
 EMy+uJnhGpkGxX0QAIOavB96wkAP4msMzCMIKyKX8NBVWEYzLy7Ou6IrPKiGOR28
 CjDi1C5qW7838H4neA6Gfw896rfTiAODhoiOY/RTXI7p2hTUUXHQuJ81Bad75gHD
 744BUMPy37YJnvgHTasYn0GxAvP73YmV+omRxo76poetYZ9eH8dGECvC9q6m+jRU
 XaubWEq1JMvzHvlyO7BIrndGY4ByRbBoG0XPiZF07e5YDkKWQmv56tgAAN7fEkeh
 8HIg8lG2xvgf+w6cDbrQ2c8fp055OvrOq40R2pSXwQgYYKXPJ+vFiNzriQ6Rfxai
 gIYrB+mrKZcY6mi6OhoulGfNxT65VqMqnUfwVbbwlJQbDe5EkV6o/1WYdaBvdO2s
 qTT9A5alabFzbQ8ZtjzsIHtV62LwmZlMWk7gxZlcvLFNjf/P2CMqqnJi30/JlrsE
 iqhwIGRDhMq4QZZbiiEiJEaEn6vh2zseRdmCy3uMFearXKBP/I2177QOTDG7ZMKf
 fZR4ROlv6c5tIpBCOsTV0+7c/fnnnOTHU4+vJiUzU0krkPzaLcL8iMT1tn+uGchX
 4d2XLuT6AbVxQR4N8YF4FwRzB/PbEb+ZWWGu1mOVSd9/dsA43K50zNdc061dgz8K
 q8lau6bmtfUXdbeWa3WMEaAZIuSBmFarJY0tPZV6W7cXUAgKitThRD6fp4E0
 =vTFa
 -----END PGP SIGNATURE-----

Merge tag 'usb-for-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next

Felipe writes:

usb: patches for v4.9 merge window

This time around we have 92 non-merge commits. Most
of the changes are in drivers/usb/gadget (40.3%)
with drivers/usb/gadget/function being the most
active directory (27.2%).

As for UDC drivers, only dwc3 (26.5%) and dwc2
(12.7%) have really been active.

The most important changes for dwc3 are better
support for scatterlist and, again, throughput
improvements. While on dwc2 got some minor stability
fixes related to soft reset and FIFO usage.

Felipe Tonello has done some good work fixing up our
f_midi gadget and Tal Shorer has implemented a nice
API change for our ULPI bus.

Apart from these, we have our usual set of
non-critical fixes, spelling fixes, build warning
fixes, etc.
2016-09-14 20:37:50 +02:00
Felipe Balbi b281dc630b usb: dwc3: of-simple: add compatible for Cavium
Add necessary compatible flag for Cavium's DWC3 so
dwc3-of-simple will probe.

Tested-by: Steven J. Hill <Steven.Hill@cavium.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-09-13 09:28:59 +03:00
Felipe Balbi 26c9cac402 usb: dwc3: of-simple: allow glues without clocks
Instead of erroring out when we don't have clocks,
let's just avoid any calls to the clk API.

Tested-by: Steven J. Hill <Steven.Hill@cavium.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-09-13 08:40:40 +03:00
Greg Kroah-Hartman fc9104d5d7 Merge 4.8-rc6 into usb-next
We want the USB fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-09-12 09:15:26 +02:00
Anurag Kumar Vulisha 8d53e62675 usb: dwc3: of-simple: Fix warning during unbind
In dwc3_of_simple_remove() we are using clk_unprepare() before doing
any clk_disable(). If we enable Common CLK framework (CCF) and try to
unbind dwc3-of-simple driver, we see kernel WARN messages.

This patch fixes this kernel warning by using clk_disable_unprepare()
instead of clk_unprepare().

Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-09-12 10:07:24 +03:00
Lu Baolu 5e6c88d28c usb: dwc3: fix Clear Stall EP command failure
Commit 50c763f8c1 ("usb: dwc3: Set the ClearPendIN bit on Clear
Stall EP command") sets ClearPendIN bit for all IN endpoints of
v2.60a+ cores. This causes ClearStall command fails on 2.60+ cores
operating in HighSpeed mode.

In page 539 of 2.60a specification:

"When issuing Clear Stall command for IN endpoints in SuperSpeed
mode, the software must set the "ClearPendIN" bit to '1' to
clear any pending IN transcations, so that the device does not
expect any ACK TP from the host for the data sent earlier."

It's obvious that we only need to apply this rule to those IN
endpoints that currently operating in SuperSpeed mode.

Fixes: 50c763f8c1 ("usb: dwc3: Set the ClearPendIN bit on Clear Stall EP command")
Cc: <stable@vger.kernel.org> # v4.7+
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-09-12 10:05:55 +03:00
Arnd Bergmann d6e10bf2ba usb: dwc3: avoid -Wmaybe-uninitialized warning
Cleaning up the loop in dwc3_cleanup_done_reqs() introduced a
gcc warning if built with "-Wmaybe-uninitialized":

drivers/usb/dwc3/gadget.c: In function 'dwc3_endpoint_transfer_complete':
drivers/usb/dwc3/gadget.c:2015:9: 'trb' may be used uninitialized in this function [-Wmaybe-uninitialized]

I believe it is a false positive and we always have a valid 'trb'
pointer at the end of the function, but neither I nor the compiler
are able to prove that.

This works around the warning by computing a flag earlier in the function
when it's guaranteed to be valid, which tells the compiler that it's
safe and makes it easier to understand to me.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 31162af447 ("usb: dwc3: gadget: avoid while (1) loop on completion")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-09-09 14:56:06 +03:00
Felipe Balbi 696118c016 usb: dwc3: pci: fix build warning on !PM_SLEEP
When building a kernel with CONFIG_PM_SLEEP=n, we
get the following warning:

drivers/usb/dwc3/dwc3-pci.c:253:12: warning: 'dwc3_pci_pm_dummy' defined but not used

In order to fix this, we should only define
dwc3_pci_pm_dummy() when CONFIG_PM_SLEEP is defined.

Fixes: f6c274e11e ("usb: dwc3: pci: runtime_resume child device")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-09-07 15:37:36 +03:00
Thinh Nguyen 9d6173e125 usb: dwc3: Fix dr_mode validation
This patch follows the similar fix in dwc2. See
commit 5268ed9d2e ("usb: dwc2: Fix dr_mode validation")

Currently, the dr_mode is only checked against the module configuration.
It also needs to be checked against the hardware capablities.

The driver now checks if both the module configuration and hardware are
capable of the dr_mode value. If not, then it will issue a warning and
fall back to a supported value. If it is unable to fall back to a
suitable value, then the probe will fail.

Behavior summary:

      module          :  actual
 HW   config  dr_mode :  dr_mode
---------------------------------
 host  host   any     :  host
 host  dev    any     :  INVALID
 host  otg    any     :  host

 dev   host   any     :  INVALID
 dev   dev    any     :  dev
 dev   otg    any     :  dev

 otg   host   any     :  host
 otg   dev    any     :  dev
 otg   otg    any     :  dr_mode

Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-09-07 13:29:20 +03:00
Tal Shorer 073c47aca7 usb: dwc3: ulpi: make dwc3_ulpi_ops constant
ulpi_register_interface() accepts a const struct ulpi_ops and dwc3
doesn't perform any changes to this struct at runtime, so there's no
reason it shouldn't be constant.

Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Tal Shorer <tal.shorer@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-09-06 10:47:26 +03:00
Tal Shorer e6f7484978 usb: ulpi: rename operations {read|write}_dev to simply {read|write}
With the removal of the old {read|write} operations, we can now safely
rename the new api operations {read|write}_dev to use the shorter and
clearer names {read|write}, respectively.

Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Tal Shorer <tal.shorer@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-09-06 10:47:24 +03:00
Tal Shorer b7cf1dc341 usb: dwc3: ulpi: use new api
The old read, write callbacks in struct ulpi_ops have been deprecated
in favor of new callbacks that pass the parent device directly.
Replace the used callbacks in dwc3's ulpi component with the new api.

Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Tal Shorer <tal.shorer@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-09-06 10:47:24 +03:00
John Youn 9d7aba7786 Revert "usb: dwc3: gadget: always decrement by 1"
This reverts commit 6f8245b4e3 ("usb: dwc3: gadget: always decrement
by 1").

We can't always decrement this value.

We should decrement only if the calculation of free slots results in a
LINK TRB being among one of the free slots (dequeue < enqueue).

Otherwise, if the LINK TRB is not among the free slots then it should
not be decremented.

Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-09-05 13:39:23 +03:00
Greg Kroah-Hartman 9b0dd49e35 Merge 4.8-rc5 into usb-testing
We want the USB fixes in here for testing and merge issues.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-09-05 08:07:58 +02:00
Felipe Balbi 6f8245b4e3 usb: dwc3: gadget: always decrement by 1
We need to decrement in both cases (enq > deq and
enq < deq)

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-25 12:30:27 +03:00
Felipe Balbi 594e121f25 usb: dwc3: gadget: stop kicking if we run out of space
In case our TRB ring is full, we can avoid trying to
kick transfers which won't start and just add requests
to the queue.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-25 12:13:21 +03:00
Felipe Balbi 7ae7df4982 usb: dwc3: gadget: abolish trbs_left
Instead, we can always rely on dwc3_calc_trbs_left()
directly.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-25 12:13:20 +03:00
John Youn 06281d460f usb: dwc3: Add ENDXFER command polling
ENDXFER polling is available on version 3.10a and later of the
DWC_usb3 (USB 3.0) controller. With this feature, the software can poll
the CMDACT bit in the DEPCMD register after issuing an ENDXFER command.
This feature is enabled by writing GUCTL2[14].

This feature is NOT available on the DWC_usb31 (USB 3.1) IP.

Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-25 12:13:19 +03:00
John Youn 512e47572f usb: dwc3: Add revision numbers for the USB 3.0 IP
Add revision number constants for the 3.00a and 3.10a releases.

Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-25 12:13:18 +03:00
Baolin Wang 00af62330c usb: dwc3: core: Move the mode setting to the right place
When dwc3 core enters into suspend mode, the system (especially for mobile
device) may power off the dwc3 controller for power saving, that will cause
dwc3 controller lost the mode operation when resuming dwc3 core.

Thus we can move the mode setting into dwc3_core_init() function to avoid this
issue.

Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-25 12:13:16 +03:00
William Wu f652191be3 usb: dwc3: of-simple: add compatible for rockchip rk3399
Rockchip platform merely enable usb3 clocks and
populate its children. So we can use this generic
glue layer to support Rockchip dwc3.

Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-25 12:13:12 +03:00
William Wu 00fe081dc3 usb: dwc3: add dis_del_phy_power_chg_quirk
Add a quirk to clear the GUSB3PIPECTL.DELAYP1TRANS bit,
which specifies whether disable delay PHY power change
from P0 to P1/P2/P3 when link state changing from U0
to U1/U2/U3 respectively.

Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-25 12:13:11 +03:00
William Wu 32f2ed864d usb: dwc3: make usb2 phy utmi interface configurable
Support to configure the UTMI+ PHY with an 8- or 16-bit
interface via DT. The UTMI+ PHY interface is a hardware
capability, and it's platform dependent. Normally, the
PHYIF can be configured during coreconsultant.

But for some specific USB cores(e.g. rk3399 SoC DWC3),
the default PHYIF configuration value is false, so we
need to reconfigure it by software.

Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-25 12:13:11 +03:00
William Wu 16199f3389 usb: dwc3: add dis_u2_freeclk_exists_quirk
Add a quirk to clear the GUSB2PHYCFG.U2_FREECLK_EXISTS bit,
which specifies whether the USB2.0 PHY provides a free-running
PHY clock, which is active when the clock control input is active.

Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-25 12:13:11 +03:00
Felipe Balbi dc55c67e9c usb: dwc3: gadget: improve increment request->actual
No functional changes, just a slight cosmetic
change.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-25 12:13:06 +03:00
Felipe Balbi f99f53f24d usb: dwc3: gadget: remove condition that never happens
We don't use LST bit anymore, so this condition will
never trigger.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-25 12:13:06 +03:00
Felipe Balbi 1f512119a0 usb: dwc3: gadget: add remaining sg entries to ring
Upon transfer completion after a full ring, let's
add more TRBs to our ring in order to complete our
request successfully.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-25 12:12:58 +03:00
Felipe Balbi 696fe69d7e usb: dwc3: debug: fix ep name on trace output
There was a typo when generating endpoint name which
would be very confusing when debugging. Fix it.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-25 10:36:25 +03:00
Felipe Balbi 2c78c0295f usb: dwc3: gadget: interrupt on ring full too
If the ring is full and we are processing a big
sglist, then let's interrupt so we can, later, add
more TRBs to the ring.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-22 10:45:37 +03:00
Felipe Balbi 0b3e4af3c7 usb: dwc3: gadget: add sg and num_pending_sgs to dwc3_request
These two fields will be used in a follow-up patch
to track how many entries of request's sglist we
have already processed. The reason is that if a
gadget driver sends an sglist with more entries then
we can fit in the ring, we will have to continue
processing remaining afterwards.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-22 10:45:37 +03:00
Felipe Balbi 31162af447 usb: dwc3: gadget: avoid while (1) loop on completion
We know that we have to iterate over the list of
started requests. Instead of looping forever, we can
rely on list_for_each_entry(). Likewise, instead of
a do {} while loop over all, maybe available,
scatterlist entries, we can detect if $this request
uses scatterlist and rely on for_each_sg().

This makes the code easier to follow while making
sure that we will *always* break out of the loop.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-22 10:45:37 +03:00
Felipe Balbi 08a36b5438 usb: dwc3: gadget: simplify __dwc3_gadget_ep_queue()
Many of the comments in that function are really
outdated and don't match what the driver is
doing. Moreover, recent patches combined programming
model for all non-control endpoints, this gives us
an opportunity to get rid of our special cases in
__dwc3_gadget_ep_queue().

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-22 10:45:37 +03:00
Felipe Balbi 45438a0cd9 usb: dwc3: gadget: simplify dwc3_ep_prev_trb()
We always need to decrement our index by at least
one. Simplify the implementation by using a
temporary local variable and making sure that we
will always decrement one extra if tmp == 0.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-22 10:45:37 +03:00
Felipe Balbi 737f1ae255 usb: dwc3: gadget: increment dequeue pointer on completion
Instead of waiting until giveback before
incrementing the dequeue pointer, we can increment
it from dwc3_cleanup_done_reqs(), that way we avoid
an extra loop over all TRBs during giveback.

While at that, also avoid using req->first_trb_index
as that's completely unnecessary. A follow-up patch
will clean up further uses of that and remove the
field altogether.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-22 10:45:37 +03:00
Felipe Balbi 4bc48c9747 usb: dwc3: gadget: retire LST bit completely
The only endpoint which actually requires LST bit
and XferComplete is ep0/1. Let's save some time by
completely removing LST bit support and
XferComplete.

This simplifies and consolidates endpoint handling
for all other 3 transfer types while also avoiding
extra interrupts.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-22 10:45:37 +03:00
Nicolas Saenz Julienne d6011f6fc2 usb: dwc3: gadget: don't rely on jiffies while holding spinlock
__dwc3_gadget_wakeup() is called while holding a spinlock, then depends on
jiffies in order to timeout while polling the USB core for a link state
update. In the case the wakeup failed, the timeout will never happen and
will also cause the cpu to stall until rcu_preempt kicks in.

This switches to a "decrement variable and wait" timeout scheme.

Signed-off-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-22 10:45:13 +03:00
Felipe Balbi b74c2d875b usb: dwc3: core: allow device to runtime_suspend several times
After going through runtime_suspend/runtime_resume
cycle once we would be left with an unbalanced
pm_runtime_get() call. Fix that by making sure that
we try to suspend right after resuming so things are
balanced and device can runtime_suspend again.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-22 10:45:11 +03:00
Felipe Balbi f6c274e11e usb: dwc3: pci: runtime_resume child device
During runtime_resume of dwc3-pci.c, we need to
runtime suspend our child device (which is dwc3
proper) otherwise nothing will happen.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-22 10:45:10 +03:00
Greg Kroah-Hartman 1aaaa9acae Merge 4.8-rc3 into usb-next
We want the USB fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-21 21:33:17 -04:00
Felipe Balbi a0ad85ae86 usb: dwc3: gadget: stop processing on HWO set
stop consuming TRBs when we reach one with HWO bit
already set. This will prevent us from prematurely
retiring a TRB.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-11 15:09:48 +03:00
Janusz Dziedzic 79d17482a4 usb: dwc3: don't set last bit for ISOC endpoints
According to Synopsys Databook 2.60a, section 8.3.4,
it's stated that:

	The LST bit should be set to 0 (isochronous
	transfers normally continue until the
	endpoint is removed entirely, at which time
	an End Transfer command is used to stop the
	transfer).

This patch makes sure that detail is observed and
fixes a regression with Android Audio playback
caused by recent changes to DWC3 gadget.

Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-11 15:09:48 +03:00
Wei Yongjun 4c4f106c03 usb: dwc3: fix missing platform_set_drvdata() in dwc3_of_simple_probe()
Add missing platform_set_drvdata() in dwc3_of_simple_probe(), otherwise
calling platform_get_drvdata() in remove returns NULL.

This is detected by Coccinelle semantic patch.

Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-11 15:09:45 +03:00
Heikki Krogerus 4491ed5042 usb: dwc3: pci: add Intel Kabylake PCI ID
Intel Kabylake PCH has the same DWC3 than Intel
Sunrisepoint. Add the new ID to the supported devices.

Cc: <stable@vger.kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-10 14:15:58 +03:00
Felipe Balbi 7c705dfe2e usb: dwc3: gadget: always cleanup all TRBs
If we stop earlier due to short packet, we will
not be able to giveback all TRBs.

Cc: <stable@vger.kernel.org>
Cc: Brian E Rogers <brian.e.rogers@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-10 14:15:57 +03:00
Felipe Balbi e5b36ae2f8 usb: dwc3: gadget: fix for short pkts during chained xfers
DWC3 has one interesting peculiarity with chained
transfers. If we setup N chained transfers and we
get a short packet before processing all N TRBs,
DWC3 will (conditionally) issue a XferComplete or
XferInProgress event and retire all TRBs from the
one which got a short packet to the last without
clearing their HWO bits.

This means SW must clear HWO bit manually, which
this patch is doing.

Cc: <stable@vger.kernel.org>
Cc: Brian E Rogers <brian.e.rogers@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-10 14:15:57 +03:00
Felipe Balbi c7de573471 usb: dwc3: gadget: increment request->actual once
When using SG lists, we would end up setting
request->actual to:

	num_mapped_sgs * (request->length - count)

Let's fix that up by incrementing request->actual
only once.

Cc: <stable@vger.kernel.org>
Reported-by: Brian E Rogers <brian.e.rogers@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-08-10 14:15:57 +03:00
Masahiro Yamada a26a142275 usb: remove redundant dependency on USB_SUPPORT
The whole Kconfig entries of the USB subsystem are surrounded with
"if USB_SUPPORT" ... "endif", so CONFIG_USB_SUPPORT=y is surely met
when these two Kconfig options are visible.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-08-09 16:15:44 +02:00
Greg Kroah-Hartman c318a821b9 Merge 4.7-rc6 into usb-next
We want the USB fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-07-04 08:19:21 -07:00
Linus Torvalds 0d064a7b9c - Final patches fixing Reset API change
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABCAAGBQJXdkJCAAoJEFGvii+H/Hdh4fIP/0U47cICszk6AkV2P3q3yRc6
 RyIfjBddVxAnNnUQoJAkyDnZmZnCH33wMa3NG8BlXCrtPUSMoUkG78RIN6mWjgp6
 pooaXBylqIiU4ZoyQVXvxTQZhM7u/ox+2InrXOeZXirkJvRY4GzwsNWtdhzclHq2
 iM86K1cfaIPdJ4d3y7WF6/5DOsdMiYQUvmtxLEYTKgJgGvkgM/9I7Ws8vk3R0lXk
 wO8EItxIZecAIEwfwI8HgYCoyPctevMSnXMTWAJTF+5m3Wprhhv0lEjCTEBHbmJb
 kkrAr86tNj4nNVG9pQCDYL/XX0Zpub0vTA4+mPL5/WTrVpI/RRYlJXKIlR25vvlN
 wlYRrY4mE4gKFJh7t6DhQiHdrrQcoWPymKZ7CSF2GZvc65xwBa0u3ZkeLhurgj0N
 C8Zj7QRIqHfP4O8JDMRvuToWJWtc8sfSvh2Y9szkevwNjZjO9INSM/hStfJZ1S0E
 EnZIcHSKehjdiLHiMgyWGRB3Fq24u41u8aVAGvCfCsSe7CZKYKzyAHEQSC7solSJ
 GmbJ6F2gB65v62rNReZeP9NCc25fex7ZkdYMr6XYqrSh7GoxtF+9VPHEvYXs5BVK
 +rVVCOvuvqSy4+oQ+N/0grLHIThqSVbAusXBSLFPykHO7R4Z30f3wIiSPTq8m2VW
 c5qwGR4ceOBRrX8fQw0c
 =PpU9
 -----END PGP SIGNATURE-----

Merge tag 'mfd-fixes-4.7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd

Pull more MFD fixes from Lee Jones:
 "Apologies for missing these from the first pull request.

  Final patches fixing Reset API change"

* tag 'mfd-fixes-4.7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
  usb: dwc3: st: Use explicit reset_control_get_exclusive() API
  phy: phy-stih407-usb: Use explicit reset_control_get_exclusive() API
  phy: miphy28lp: Inform the reset framework that our reset line may be shared
2016-07-01 15:17:16 -07:00
Roger Quadros 322832f2f1 usb: dwc3: host: Fix broken XHCI host
Looks like we lost all changes related to
commit 9522def400 ("usb: dwc3: core: cleanup IRQ resources") in host.c
when Felipe's next branch was merged into Greg's next branch.

Fixes 215db94818 ("Merge tag 'usb-for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next")
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-07-01 08:59:44 -07:00
Lee Jones 5baaf3b9ef usb: dwc3: st: Use explicit reset_control_get_exclusive() API
We're making all reset line users specify whether their lines are
shared with other IP or they operate them exclusively.  In this case
the line is exclusively used only by this IP, so use the *_exclusive()
API accordingly.

Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2016-07-01 10:52:16 +01:00
Linus Torvalds 4aa34ce3c1 - Bug Fixes
- Use new reset_*_get_shared() variant to prevent reset line obtainment failure
     - Fixes: 0b52297 ("reset: Add support for shared reset controls")
   - Fix unintentional switch() fall-through into error path
   - Fix uninitialised variable compiler warning
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABCAAGBQJXdMAeAAoJEFGvii+H/Hdh2JsQAJ5ez/+WlfVY5enmZTCPTfjv
 YAZOhGuKyK1RcNKVmhRTXKDDlEQtbzX01AG73UOsMuR6Gjfq4q+lsK88ybE6Y3MS
 YuIBa0TXicyywbLhAh4bCqbImFQZ2MhU07mJWn5n6qX1LwrxncKN5MdRj2DKzldv
 s9AG1EKUKf/83k6kuODaP8dXutvWPEGKYKXnq9MQPBliU2j7DT7mfEp3jLGlJvXy
 UkW2uq1RAhu27fe7TKVefatXLIyqo74fi3fuHVZpWfPsoUTFlQd3RzeFL7Q/orWH
 JqiUk55xAbsmtkEeKNbpph1gPyR1pzKKHiNvSfRt/yIjsxOVPGZQZA2y4OpIcOKV
 mbxPUrurhcdI+sK2+7JpcbjKYJpCsGgCXtwbLubLcgler+RatmFWOB8+ayH32eVC
 DELYFtc80YBaDS+2KrgY4la1Mk1agbfDpyhq4Vp5uiRZFhQyldd1XrPPQssMJNc+
 Zme+LRu+EQiullbHDRb6cb0dnV2Tcek4IjI1CsNA6UMAMLcVb8IZ1gX39vWr+BNt
 ZWxxoBOcskPJ/t3h4ddPbuMzSA0ctBkJct9bdjg+bpZeA0aJ46lTQCJk4fZfjViu
 YcDgO8/ZVaDLz5f4f44xJ+Hwnzxr2fezBUirD3UtPvs57BSVnFbHMBXUdy0NCBHk
 mZi1lFOjy7eKuW1+kbrx
 =mo7m
 -----END PGP SIGNATURE-----

Merge tag 'mfd-fixes-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd

Pull MFD fixes from Lee Jones:
 "Contained are some standard fixes and unusually an extension to the
  Reset API.  Some of those changes are required to fix a bug introduced
  in -rc1, which introduces extra 'reset line checks' i.e. whether the
  line is shared or not.  If a line is shared and the new *_shared() API
  is not used, the request fails with an error.  This breaks USB in v4.7
  for ST's platforms.

  Admittedly, there are some patches contained in our (MFD/Reset)
  immutable branch which are not true -fixes, but there isn't anything I
  can do about that.  Rest assured though, there aren't any API
  'changes'.  Everything is the same from the consumer's perspective.

   - Use new reset_*_get_shared() variant to prevent reset line
     obtainment failure (Fixes commit 0b52297f2288: "reset: Add support
     for shared reset controls")

   - Fix unintentional switch() fall-through into error path

   - Fix uninitialised variable compiler warning"

* tag 'mfd-fixes-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
  mfd: da9053: Fix compiler warning message for uninitialised variable
  mfd: max77620: Fix FPS switch statements
  phy: phy-stih407-usb: Inform the reset framework that our reset line may be shared
  usb: dwc3: st: Inform the reset framework that our reset line may be shared
  usb: host: ehci-st: Inform the reset framework that our reset line may be shared
  usb: host: ohci-st: Inform the reset framework that our reset line may be shared
  reset: TRIVIAL: Add line break at same place for similar APIs
  reset: Supply *_shared variant calls when using *_optional APIs
  reset: Supply *_shared variant calls when using of_* API
  reset: Ensure drivers are explicit when requesting reset lines
  reset: Reorder inline reset_control_get*() wrappers
2016-06-30 09:44:34 -07:00
Lee Jones 002f17bc54 usb: dwc3: st: Inform the reset framework that our reset line may be shared
On the STiH410 B2120 development board the MiPHY28lp shares its reset
line with the Synopsys DWC3 SuperSpeed (SS) USB 3.0 Dual-Role-Device
(DRD).  New functionality in the reset subsystems forces consumers to
be explicit when requesting shared/exclusive reset lines.

Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2016-06-30 07:44:21 +01:00
Greg Kroah-Hartman 215db94818 usb: patches for v4.8 merge window
Here's the big pull request for Peripheral stack and
 all related drivers.
 
 This time around with 109 non-merge commits mostly
 concentrated on drivers/usb/gadget/udc (41.5%) and
 drivers/usb/dwc3 (28.1%).
 
 There's a big rework on dwc3's transfer handling
 which gave us almost 3x faster USB3 speeds with Mass
 Storage on a particular test scenario I measured. We
 are also removing platform_data from dwc3 after
 converting all users to built-in properties instead.
 
 For the Gadget API, we're just adding tracepoints to
 aid debugging activities.
 
 Other than these, there's the usual set of spelling
 fixes, minor bug fixes and sparse warnings cleanups.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABCAAGBQJXc7hvAAoJEIaOsuA1yqREgCoP/3/xfIoJfDTLbTG9V898Ma07
 jSHVmaAu4FSktbYv6ndfcdn5tQxpADurc1cphCV1sT24Fdr56YsQdOxagqu892oo
 oW/WMka1bo7OlvzHqZYmy60hAEeWsAaVxqtEtpyb35Q/tH/33bxTlO+MeKmEKpIM
 HVQzMNuzXy6NxytVGu/BnSZRGtDLHZMdaRNEpn465Ll9mP6zm7ebdWnkIGniGRZ+
 YeK1CfvnUcSxmaB83Gr5kthFJUhi5rpX421301FdtkY4cUtZad+FlN0UW3fd8ztC
 hGr2fr+CZO7zVJ/KmEvarTLvYN0ScSjyS0VX9TT/voxJbjqZaIew0mkUWLpdxpYW
 J4i921j5pSVuK9VRbnhObxenLsW66zoqFtHeQ7pRDm3sX2fJGAX5qB6Votw4ziar
 puwE3cQ4Divk6CGEcnUmZ26KvYE/sW7W8WoKAeMMjIinJN46geLjAiqA5dpYxYuH
 ipCe1YdbjpG4GOnTjajZodGUXlmCPbs2VmcgIH36jbQ8S1m1Q3wuO9ClAO8MvGmr
 Y5HzbUeEDyJe4ZKzT9iOWtj0PAa1YEvpSRLwpZaehycQLKvbd0rRDIQ4p+oq7QDK
 gAN+kWCnkNup7qzAD6aE0FrJtYt5u5qVmPfp1H9z8+/AfmG8QZpy2d+VQsAhIwI+
 9d2bok3rsfi87lEFVRWg
 =PT1e
 -----END PGP SIGNATURE-----

Merge tag 'usb-for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next

Felipe writes:

usb: patches for v4.8 merge window

Here's the big pull request for Peripheral stack and
all related drivers.

This time around with 109 non-merge commits mostly
concentrated on drivers/usb/gadget/udc (41.5%) and
drivers/usb/dwc3 (28.1%).

There's a big rework on dwc3's transfer handling
which gave us almost 3x faster USB3 speeds with Mass
Storage on a particular test scenario I measured. We
are also removing platform_data from dwc3 after
converting all users to built-in properties instead.

For the Gadget API, we're just adding tracepoints to
aid debugging activities.

Other than these, there's the usual set of spelling
fixes, minor bug fixes and sparse warnings cleanups.
2016-06-29 09:51:48 -07:00
Heikki Krogerus 95b57df450 usb: dwc3: host: use build-in property instead of platform data
This should allow xhci to remove handling of platform data.

Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-06-26 11:43:39 -07:00
Baolin Wang 72704f876f dwc3: gadget: Implement the suspend entry event handler
It had changed to be suspend event for BIT6 in DEVT register from
version 2.30a and above. Thus this patch introduces one suspend
event handler to handle the suspend event.

Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-06-21 11:16:01 +03:00
Roger Quadros 9522def400 usb: dwc3: core: cleanup IRQ resources
Implementations might use different IRQs for
host, gadget so use named interrupt resources
to allow device tree to specify the interrupts.

Following are the interrupt names

Peripheral Interrupt - peripheral
HOST Interrupt - host

Maintain backward compatibility for a single named
interrupt ("dwc3_usb3") for all interrupts as well as
unnamed interrupt at index 0 for all interrupts.

As platform_get_irq() variants are used, tackle
the -EPROBE_DEFER case as well.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-06-21 10:53:22 +03:00
Baolin Wang da1410be21 usb: dwc3: gadget: Add the suspend state checking when stopping gadget
It will be crash to stop gadget when the dwc3 device had been into suspend
state, thus we need to check if the dwc3 device had been into suspend state
when UDC try to stop gadget.

Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-06-21 10:44:37 +03:00
Felipe Balbi 0e146028ee usb: dwc3: gadget: issue ENDTRANSFER conditional on resource_index
Because of recent changes to transfer handling on
DWC3, we will not get XferComplete unless we
completely fill up our TRB ring. This means that we
might get a Reset or Disconnect without getting a
XferComplete first.

In order to correctly release our allocated Transfer
Resource, we must issue ENDTRANSFER command whenever
dep->resource_index is valid.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-06-21 10:38:44 +03:00
Roger Quadros 328082376a usb: dwc3: fix runtime PM in error path
If there is a failure after pm_runtime_enable/get_sync()
we need to call pm_runtime_disable/put_sync().

Otherwise it will lead to an unbalanced pm_runtime_enable() on the
subsequent probe if the earlier probe bailed out due to -EPROBE_DEFER.

pm_runtime_get_sync() can fail as well so deal with that case too.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-06-21 10:38:43 +03:00
Felipe Balbi b6d4e16e83 usb: dwc3: gadget: simplify run_stop() break condition
it's clear now that when is_on=true, we must loop
until DWC3_DSTS_DEVCTRLHLT clears; while when
is_on=false we must loop until DWC3_DSTS_DEVCTRLHLT
gets set.

Instead of adding actual if() statements, we can
rely on XOR operation to evaluate to true only when
the above conditions apply. Then, we can move the
break condition back to the while() statement
together with our timeout check and the resulting
code is very compact and simpler to read.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-06-21 10:38:43 +03:00
Felipe Balbi f2df679b6c usb: dwc3: gadget: avoid while(1) in run_stop()
instead of looping forever and forcing a return if
timeout reaches zero, we can just use timeout and
loop's break condition directly.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-06-21 10:38:43 +03:00
Felipe Balbi d807bdd028 usb: dwc3: gadget: remove udelay() from run_stop()
testing shows that udelay() is unnecessary as
controller reaches Halted state almost
instantenously as can be seen by our timeout
variable never actually decrementing.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-06-21 10:38:42 +03:00
Felipe Balbi 5f82279a0c usb: dwc3: core: fixup dr_mode fallback selection
We shouldn't change a host-only dwc3 to gadget-only
if driver is built as gadget-only. Fix that up here.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-06-21 10:38:42 +03:00
Felipe Balbi e6fe66fe08 usb: dwc3: pci: add dr-mode for Intel dwc3
It's know that Intel's SoCs' dwc3 integration is
peripheral-only since Intel implements its own
portmux for role-swapping. In order to prevent dwc3
from ever registering and XHCI platform_device,
let's just set dr-mode to peripheral-only on Intel
SoCs.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-06-21 10:38:42 +03:00
Felipe Balbi 21e64bf20d usb: dwc3: gadget: rename 'ignore' argument to 'modify'
'modify' is what the current action is called. Let's
rename it so it matches databook. While at that,
also make sure to add support 'init' action too.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-06-21 10:38:41 +03:00
Felipe Balbi d6dc2e76a8 usb: dwc3: gadget: decrement trbs_left for each sg entry
If we don't, we will overwrite valid TRBs.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-06-20 12:32:51 +03:00
Felipe Balbi ba62c09d5c usb: dwc3: gadget: start Bulk endpoints more frequently
Now we can try to issue Update Transfer every time
gadget driver queues a new request. This will make
sure we keep controller's queue busy for as long as
possible.

Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2016-06-20 12:32:51 +03:00