Initialize net_device_ops structure
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize usb_driver structure skeleton
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The manual states that the checksum cannot lie in the last DWORD of the
transmission, so add a basic check for this and fall back to software
checksumming the packet.
This only seems to trigger for ACK packets with no options or data to
return to the other end, and the use of the tx-alignment option makes
it more likely to happen.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the RX code to use get_unaligned_le32() instead of the combo
of memcpy and cpu_to_le32s(&var).
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The smsc95xx_tx_fixup is doing multiple calls to skb_push() to
put an 8-byte command header onto the packet. It would be easier
to do one skb_push() and then copy the data in once the push is
done.
We also make the code smaller by using proper unaligned puts for
the header. This merges in the CPU to LE32 conversion as well and
makes the whole sequence easier to understand hopefully.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The smsc95xx driver already takes into account the NET_IP_ALIGN
parameter when setting up the receive packet data, which means
we do not need to worry about aligning the packets in the usbnet
driver.
Adding the EVENT_NO_IP_ALIGN means that the IPv4 header is now
passed to the ip_rcv() routine with the start on an aligned address.
Tested on Raspberry Pi B3.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few MAC/PHYs combinations which now support > 1Gbps. These
may need to make use of link modes with bits > 31. Thus their
supported PHY features or advertised features cannot be implemented
using the current bitmap in a u32. Convert to using a linkmode bitmap,
which can support all the currently devices link modes, and is future
proof as more modes are added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit f77f0aee4d ("net: use core MTU range checking in USB NIC
drivers") introduce a common MTU handling for usbnet. But it's missing
the necessary changes for smsc95xx. So set the MTU range accordingly.
This patch has been tested on a Raspberry Pi 3.
Fixes: f77f0aee4d ("net: use core MTU range checking in USB NIC drivers")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to make sure, that the carrier check polling is disabled
while suspending. Otherwise we can end up with usbnet_read_cmd()
being issued when only usbnet_read_cmd_nopm() is allowed. If this
happens, read operations lock up.
Fixes: d69d169493 ("usbnet: smsc95xx: fix link detection for disabled autonegotiation")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Raghuram Chary J <RaghuramChary.Jallipalli@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts were easy to resolve using immediate context mostly,
except the cls_u32.c one where I simply too the entire HEAD
chunk.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/usb/cdc_ncm.c: In function 'cdc_ncm_status':
drivers/net/usb/cdc_ncm.c:1603:22: warning:
variable 'ctx' set but not used [-Wunused-but-set-variable]
struct cdc_ncm_ctx *ctx;
It not used any more after
commit fa83dbeee5 ("net: cdc_ncm: remove redundant "disconnected" flag")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tasklet initialisation would be better done by tasklet_init()
instead of assuming all the fields are in an ok state by default.
This does not fix any actual know bug.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for Gemalto's Cinterion ALASxx WWAN interfaces
by adding QMI_FIXED_INTF with Cinterion's VID and PID.
Signed-off-by: Giacinto Cifelli <gciofono@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cancel pending work before freeing smsc75xx private data structure
during binding. This fixes the following crash in the driver:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000050
IP: mutex_lock+0x2b/0x3f
<snipped>
Workqueue: events smsc75xx_deferred_multicast_write [smsc75xx]
task: ffff8caa83e85700 task.stack: ffff948b80518000
RIP: 0010:mutex_lock+0x2b/0x3f
<snipped>
Call Trace:
smsc75xx_deferred_multicast_write+0x40/0x1af [smsc75xx]
process_one_work+0x18d/0x2fc
worker_thread+0x1a2/0x269
? pr_cont_work+0x58/0x58
kthread+0xfa/0x10a
? pr_cont_work+0x58/0x58
? rcu_read_unlock_sched_notrace+0x48/0x48
ret_from_fork+0x22/0x40
Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflict in net/core/rtnetlink.c, David Ahern's bug fix in 'net'
overlapped the renaming of a netlink attribute in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver_info field that is used for describing each of the usb-net
drivers using the usbnet.c core all declare their information as const
and the usbnet.c itself does not try and modify the struct.
It is therefore a good idea to make this const in the usbnet.c structure
in case anyone tries to modify it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver does not check for Wake-on-LAN modes specified by an user,
but will conditionally set the device as wake-up enabled or not based on
that, which could be a very confusing user experience.
Fixes: e0e474a83c ("smsc95xx: add wol magic packet support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver does not check for Wake-on-LAN modes specified by an user,
but will conditionally set the device as wake-up enabled or not based on
that, which could be a very confusing user experience.
Fixes: 6c63650326 ("smsc75xx: add wol magic packet support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver does not check for Wake-on-LAN modes specified by an user,
but will conditionally set the device as wake-up enabled or not based on
that, which could be a very confusing user experience.
Fixes: 21ff2e8976 ("r8152: support WOL")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently silently accepts unsupported Wake-on-LAN modes
(other than WAKE_PHY or WAKE_MAGIC) without reporting that to the user,
which is confusing.
Fixes: 19a38d8e0a ("USB2NET : SR9800 : One chip USB2.0 USB2NET SR9800 Device Driver Support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver supports a fair amount of Wake-on-LAN modes, but is not
checking that the user specified one that is supported.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Woojung Huh <Woojung.Huh@Microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently silently accepts unsupported Wake-on-LAN modes
(other than WAKE_PHY or WAKE_MAGIC) without reporting that to the user,
which is confusing.
Fixes: e2ca90c276 ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently silently accepts unsupported Wake-on-LAN modes
(other than WAKE_PHY or WAKE_MAGIC) without reporting that to the user,
which is confusing.
Fixes: 2e55cc7210 ("[PATCH] USB: usbnet (3/9) module for ASIX Ethernet adapters")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns when a variable is assigned to itself.
drivers/net/usb/lan78xx.c:940:11: warning: explicitly assigning value of
variable of type 'u32' (aka 'unsigned int') to itself [-Wself-assign]
offset = offset;
~~~~~~ ^ ~~~~~~
1 warning generated.
Reorder the if statement to acheive the same result and avoid a self
assignment warning.
Link: https://github.com/ClangBuiltLinux/linux/issues/129
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two new tls tests added in parallel in both net and net-next.
Used Stephen Rothwell's linux-next resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent firmware revisions have added the ability to force
these modems to USB2 mode, hiding their SuperSpeed
capabilities from the host. The driver has been using the
SuperSpeed capability, as shown by the bcdUSB field of the
device descriptor, to detect the need to enable the DTR
quirk. This method fails when the modems are forced to
USB2 mode by the modem firmware.
Fix by unconditionally enabling the DTR quirk for the
affected device IDs.
Reported-by: Fred Veldini <fred.veldini@gmail.com>
Reported-by: Deshu Wen <dwen@sierrawireless.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Reported-by: Fred Veldini <fred.veldini@gmail.com>
Reported-by: Deshu Wen <dwen@sierrawireless.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put has taken the null pointer check into account. So it is
safe to remove the duplicated check before of_node_put.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some MAC hardware cannot support a subset of link modes. e.g. often
1Gbps Full duplex is supported, but Half duplex is not. Add a helper
to remove such a link mode.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quectel EP06 (and EM06/EG06) supports dynamic configuration of USB
interfaces, without the device changing VID/PID or configuration number.
When the configuration is updated and interfaces are added/removed, the
interface numbers change. This means that the current code for matching
EP06 does not work.
This patch removes the current EP06 interface number match, and replaces
it with a match on class, subclass and protocol. Unfortunately, matching
on those three alone is not enough, as the diag interface exports the
same values as QMI. The other serial interfaces + adb export different
values and do not match.
The diag interface only has two endpoints, while the QMI interface has
three. I have therefore added a check for number of interfaces, and we
ignore the interface if the number of endpoints equals two.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use skb_queue_walk() instead.
Adjust inner loop test to utilize and skb_queue_is_first().
Unfortunately we have to keep pkt_cnt around because it is
used by a latter loop in this function.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes some declaration more consistent.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Raghuram Chary Jallipalli <raghuramchary.jallipalli@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need for this strcpy because alloc_etherdev() already
does this job.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Raghuram Chary Jallipalli <raghuramchary.jallipalli@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to bail out if lan78xx_get_endpoints() fails, otherwise the
result is overwritten.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Raghuram Chary Jallipalli <raghuramchary.jallipalli@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1077614 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a new Dell TB16 dock with a different iSerialNumber.
Apply the same fix from commit 0b1655143d ("r8152: disable RX
aggregation on Dell TB16 dock") to this model.
BugLink: https://bugs.launchpad.net/bugs/1785780
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl8152_system_suspend defines the variable "ret", but it is not modified
after initialization. So just remove it.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use ARRAY_SIZE to replace open code sizeof(lan78xx_regs) / sizeof(u32).
It make the code concise.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BTF conflicts were simple overlapping changes.
The virtio_net conflict was an overlap of a fix of statistics counter,
happening alongisde a move over to a bonafide statistics structure
rather than counting value on the stack.
Signed-off-by: David S. Miller <davem@davemloft.net>
As long the bh tasklet isn't scheduled once, no packet from the rx path
will be handled. Since the tx path also schedule the same tasklet
this situation only persits until the first packet transmission.
So fix this issue by scheduling the tasklet after link reset.
Link: https://github.com/raspberrypi/linux/issues/2617
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet")
Suggested-by: Floris Bos <bos@je-eigen-domein.nl>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sr9700_bind() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
setup_pegasus_II() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mii_nway_restart is not pm aware which results in a rtnl deadlock.
Implement mii_nway_restart manual by setting BMCR_ANRESTART if
BMCR_ANENABLE is set.
To reproduce:
* plug an asix based usb network interface
* wait until the device enters PM (~5 sec)
* `ip link set eth1 up` will never return
Fixes: d9fe64e511 ("net: asix: Add in_pm parameter")
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver can spam the kernel log with multiple messages of:
net eth0: eth0: allmulti set
Usually 4 or 8 at a time (probably because of using ConnMan).
This message doesn't seem useful, so let's demote it from dev_info()
to dev_dbg().
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb size calculation in lan78xx_tx_bh is in race with the start_xmit,
which could lead to rare kernel oopses. So protect the whole skb walk with
a spin lock. As a benefit we can unlink the skb directly.
This patch was tested on Raspberry Pi 3B+
Link: https://github.com/raspberrypi/linux/issues/2608
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Floris Bos <bos@je-eigen-domein.nl>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the swap macro and remove unnecessary variable *temp*.
This makes the code easier to read and maintain. Also, slightly
refactor some code due to the removal of *temp*.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the USB id of LTE modem Quectel EG91. It requires the
same quirk as other Quectel modems to make it work.
Signed-off-by: Matevz Vucnik <vucnikm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
In certain conditions, the device may not be able to link in gigabit mode. This software workaround ensures that the device will not enter the failure state.
Fixes: d0cad87170 ("SMSC75XX USB 2.0 Gigabit Ethernet Devices")
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For Embedded use where e.g. AX88772B chips may be used without external
EEPROMs the boot loader may choose to pass the MAC address to be used
via device tree. Therefore, allow for optionally getting the MAC
address from device tree data e.g. as follows (excerpt from a T30 based
board, local-mac-address to be filled in by boot loader):
/* EHCI instance 1: USB2_DP/N -> AX88772B */
usb@7d004000 {
status = "okay";
#address-cells = <1>;
#size-cells = <0>;
asix@1 {
reg = <1>;
local-mac-address = [00 00 00 00 00 00];
};
};
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple overlapping changes in stmmac driver.
Adjust skb_gro_flush_final_remcsum function signature to make GRO list
changes in net-next, as per Stephen Rothwell's example merge
resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Observations of VLANs dropping packets due to invalid
checksums when not offloading VLAN tag receive.
With VLAN tag stripping enabled no issue is observed.
Drop back to s/w checksums if VLAN offload is disabled.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip supports stripping the VLAN tag and reporting it
in metadata.
Complete the support for this.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW_VLAN_CTAG_FILTER was partially implemented, but not advertised
to Linux.
Complete the implementation of this.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The frame abort timeout being set by lan78xx_set_rx_max_frame_length
didn't account for any VLAN headers, resulting in very low
throughput if used with tagged VLANs.
Use VLAN_ETH_HLEN instead of ETH_HLEN to correct for this.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When unplugging an r8152 adapter while the interface is UP, the NIC
becomes unusable. usb->disconnect (aka rtl8152_disconnect) deletes
napi. Then, rtl8152_disconnect calls unregister_netdev and that invokes
netdev->ndo_stop (aka rtl8152_close). rtl8152_close tries to
napi_disable, but the napi is already deleted by disconnect above. So
the first while loop in napi_disable never finishes. This results in
complete deadlock of the network layer as there is rtnl_mutex held by
unregister_netdev.
So avoid the call to napi_disable in rtl8152_close when the device is
already gone.
The other calls to usb_kill_urb, cancel_delayed_work_sync,
netif_stop_queue etc. seem to be fine. The urb and netdev is not
destroyed yet.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: linux-usb@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This module exposes two USB configurations: a QMI+AT capable setup on
USB config #1 and a MBIM capable setup on USB config #2.
By default the kernel will choose the MBIM capable configuration as
long as the cdc_mbim driver is available. This patch adds support for
the QMI port in the secondary configuration.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
random_ether_addr is a #define for eth_random_addr which is
generally preferred in kernel code by ~3:1
Convert the uses of random_ether_addr to enable removing the #define
Miscellanea:
o Convert &vfmac[0] to equivalent vfmac and avoid unnecessary line wrap
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Cc: Petko Manolov <petkan@nucleusys.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code does:
if (hrtimer_active(&t))
hrtimer_cancel(&t);
However, hrtimer_cancel() checks if the timer is active, so the
test above is pointless.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Filling in the padding slot in the bpf structure as a bug fix in 'ne'
overlapped with actually using that padding area for something in
'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Testing Telit LM940 with ICMP packets > 14552 bytes revealed that
the modem needs FLAG_SEND_ZLP to properly work, otherwise the cdc
mbim data interface won't be anymore responsive.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for Netgear Aircard 779S
Signed-off-by: Josh Hill <josh@joshuajhill.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
SIMCOM are reusing a single device ID for many (all of their?)
different modems, based on different chipsets and firmwares. Newer
Qualcomm chipset generations require setting DTR to wake the QMI
function. The SIM7600E modem is using such a chipset, making it
fail to work with this driver despite the device ID match.
Fix by unconditionally enabling the SET_DTR quirk for all SIMCOM
modems using this specific device ID. This is similar to what
we already have done for another case of device IDs recycled over
multiple chipset generations: 14cf4a771b ("drivers: net: usb:
qmi_wwan: add QMI_QUIRK_SET_DTR for Telit PID 0x1201")
Initial testing on an older SIM7100 modem shows no immediate side
effects.
Reported-by: Sebastian Sjoholm <sebastian.sjoholm@gmail.com>
Cc: Reinhard Speyerer <rspmn@arcor.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of drivers have the following pattern:
if (np)
of_mdiobus_register()
else
mdiobus_register()
which the implementation of of_mdiobus_register() now takes care of.
Remove that pattern in drivers that strictly adhere to it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The USB_DEVICE_INTERFACE_NUMBER matching macro assumes that
the { vendorid, productid, interfacenumber } set uniquely
identifies one specific function. This has proven to fail
for some configurable devices. One example is the Quectel
EM06/EP06 where the same interface number can be either
QMI or MBIM, without the device ID changing either.
Fix by requiring the vendor-specific class for interface number
based matching. Functions of other classes can and should use
class based matching instead.
Fixes: 03304bcb5e ("net: qmi_wwan: use fixed interface number matching")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the error messages when phy registration fails.
Signed-off-by: Raghuram Chary J <raghuramchary.jallipalli@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove driver version info from the lan78xx driver.
Signed-off-by: Raghuram Chary J <raghuramchary.jallipalli@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding Fixed PHY support to the lan78xx driver.
Signed-off-by: Raghuram Chary J <raghuramchary.jallipalli@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to dump lan78xx family registers using ethtool, add
support at lan78xx driver level.
Signed-off-by: Raghuram Chary J <raghuramchary.jallipalli@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for DT property "microchip,led-modes", a vector of zero
to four cells (u32s) in the range 0-15, each of which sets the mode
for one of the LEDs. Some possible values are:
0=link/activity 1=link1000/activity
2=link100/activity 3=link10/activity
4=link100/1000/activity 5=link10/1000/activity
6=link10/100/activity 14=off 15=on
These values are given symbolic constants in a dt-bindings header.
Also use the presence of the DT property to indicate that the
LEDs should be enabled - necessary in the event that no valid OTP
or EEPROM is available.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a standard mechanism for locating and using a MAC address from
the Device Tree. Use this facility in the lan78xx driver to support
applications without programmed EEPROM or OTP. At the same time,
regularise the handling of the different address sources.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 92571a1aae ("lan78xx: Connect phy early") moves the PHY
initialisation into lan78xx_probe, but lan78xx_open subsequently calls
lan78xx_reset. As well as forcing a second round of link negotiation,
this reset frequently prevents the phy interrupt from being generated
(even though the link is up), rendering the interface unusable.
Fix this issue by removing the lan78xx_reset call from lan78xx_open.
Fixes: 92571a1aae ("lan78xx: Connect phy early")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Cinterion AHS8 is a 3G device with one embedded WWAN interface
using cdc_ether as a driver.
The modem is controlled via AT commands through the exposed TTYs.
AT+CGDCONT write command can be used to activate or deactivate a WWAN
connection for a PDP context defined with the same command. UE
supports one WWAN adapter.
Signed-off-by: Bassem Boubaker <bassem.boubaker@actia.fr>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
lan78xx_defer_event generates an error message whenever the work item
is already scheduled. lan78xx_open defers three events -
EVENT_STAT_UPDATE, EVENT_DEV_OPEN and EVENT_LINK_RESET. Being aware
of the likelihood (or certainty) of an error message, the DEV_OPEN
event is added to the set of pending events directly, relying on
the subsequent deferral of the EVENT_LINK_RESET call to schedule the
work. Take the same precaution with EVENT_STAT_UPDATE to avoid a
totally unnecessary error message.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
lan78xx_read_otp tries to return -EINVAL in the event of invalid OTP
content, but the value gets overwritten before it is returned and the
read goes ahead anyway. Make the read conditional as it should be
and preserve the error code.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using wicked with a lan78xx device attached to the system, we
end up with ethtool commands issued on the device before an ifup
got issued. That lead to the following crash:
Unable to handle kernel NULL pointer dereference at virtual address 0000039c
pgd = ffff800035b30000
[0000039c] *pgd=0000000000000000
Internal error: Oops: 96000004 [#1] SMP
Modules linked in: [...]
Supported: Yes
CPU: 3 PID: 638 Comm: wickedd Tainted: G E 4.12.14-0-default #1
Hardware name: raspberrypi rpi/rpi, BIOS 2018.03-rc2 02/21/2018
task: ffff800035e74180 task.stack: ffff800036718000
PC is at phy_ethtool_ksettings_get+0x20/0x98
LR is at lan78xx_get_link_ksettings+0x44/0x60 [lan78xx]
pc : [<ffff0000086f7f30>] lr : [<ffff000000dcca84>] pstate: 20000005
sp : ffff80003671bb20
x29: ffff80003671bb20 x28: ffff800035e74180
x27: ffff000008912000 x26: 000000000000001d
x25: 0000000000000124 x24: ffff000008f74d00
x23: 0000004000114809 x22: 0000000000000000
x21: ffff80003671bbd0 x20: 0000000000000000
x19: ffff80003671bbd0 x18: 000000000000040d
x17: 0000000000000001 x16: 0000000000000000
x15: 0000000000000000 x14: ffffffffffffffff
x13: 0000000000000000 x12: 0000000000000020
x11: 0101010101010101 x10: fefefefefefefeff
x9 : 7f7f7f7f7f7f7f7f x8 : fefefeff31677364
x7 : 0000000080808080 x6 : ffff80003671bc9c
x5 : ffff80003671b9f8 x4 : ffff80002c296190
x3 : 0000000000000000 x2 : 0000000000000000
x1 : ffff80003671bbd0 x0 : ffff80003671bc00
Process wickedd (pid: 638, stack limit = 0xffff800036718000)
Call trace:
Exception stack(0xffff80003671b9e0 to 0xffff80003671bb20)
b9e0: ffff80003671bc00 ffff80003671bbd0 0000000000000000 0000000000000000
ba00: ffff80002c296190 ffff80003671b9f8 ffff80003671bc9c 0000000080808080
ba20: fefefeff31677364 7f7f7f7f7f7f7f7f fefefefefefefeff 0101010101010101
ba40: 0000000000000020 0000000000000000 ffffffffffffffff 0000000000000000
ba60: 0000000000000000 0000000000000001 000000000000040d ffff80003671bbd0
ba80: 0000000000000000 ffff80003671bbd0 0000000000000000 0000004000114809
baa0: ffff000008f74d00 0000000000000124 000000000000001d ffff000008912000
bac0: ffff800035e74180 ffff80003671bb20 ffff000000dcca84 ffff80003671bb20
bae0: ffff0000086f7f30 0000000020000005 ffff80002c296000 ffff800035223900
bb00: 0000ffffffffffff 0000000000000000 ffff80003671bb20 ffff0000086f7f30
[<ffff0000086f7f30>] phy_ethtool_ksettings_get+0x20/0x98
[<ffff000000dcca84>] lan78xx_get_link_ksettings+0x44/0x60 [lan78xx]
[<ffff0000087cbc40>] ethtool_get_settings+0x68/0x210
[<ffff0000087cc0d4>] dev_ethtool+0x214/0x2180
[<ffff0000087e5008>] dev_ioctl+0x400/0x630
[<ffff00000879dd00>] sock_do_ioctl+0x70/0x88
[<ffff00000879f5f8>] sock_ioctl+0x208/0x368
[<ffff0000082cde10>] do_vfs_ioctl+0xb0/0x848
[<ffff0000082ce634>] SyS_ioctl+0x8c/0xa8
Exception stack(0xffff80003671bec0 to 0xffff80003671c000)
bec0: 0000000000000009 0000000000008946 0000fffff4e841d0 0000aa0032687465
bee0: 0000aaaafa2319d4 0000fffff4e841d4 0000000032687465 0000000032687465
bf00: 000000000000001d 7f7fff7f7f7f7f7f 72606b622e71ff4c 7f7f7f7f7f7f7f7f
bf20: 0101010101010101 0000000000000020 ffffffffffffffff 0000ffff7f510c68
bf40: 0000ffff7f6a9d18 0000ffff7f44ce30 000000000000040d 0000ffff7f6f98f0
bf60: 0000fffff4e842c0 0000000000000001 0000aaaafa2c2e00 0000ffff7f6ab000
bf80: 0000fffff4e842c0 0000ffff7f62a000 0000aaaafa2b9f20 0000aaaafa2c2e00
bfa0: 0000fffff4e84818 0000fffff4e841a0 0000ffff7f5ad0cc 0000fffff4e841a0
bfc0: 0000ffff7f44ce3c 0000000080000000 0000000000000009 000000000000001d
bfe0: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
The culprit is quite simple: The driver tries to access the phy left and right,
but only actually has a working reference to it when the device is up.
The fix thus is quite simple too: Get a reference to the phy on probe already
and keep it even when the device is going down.
With this patch applied, I can successfully run wicked on my system and bring
the interface up and down as many times as I want, without getting NULL pointer
dereferences in between.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflicts in drivers/net/ethernet/mellanox/mlx5/core/en_rep.c,
we had some overlapping changes:
1) In 'net' MLX5E_PARAMS_LOG_{SQ,RQ}_SIZE -->
MLX5E_REP_PARAMS_LOG_{SQ,RQ}_SIZE
2) In 'net-next' params->log_rq_size is renamed to be
params->log_rq_mtu_frames.
3) In 'net-next' params->hard_mtu is added.
Signed-off-by: David S. Miller <davem@davemloft.net>
Description:
Crash was reported with syzkaller pointing to lan78xx_write_reg routine.
Root-cause:
Proper cleanup of workqueues and init/setup routines was not happening
in failure conditions.
Fix:
Handled the error conditions by cleaning up the queues and init/setup
routines.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Raghuram Chary J <raghuramchary.jallipalli@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Bezrukov