Attempting to boot 32-bit ARM kernels under QEMU's 3.x virt models fails
when we have more than 512M of RAM in the model as we run out of vmalloc
space for the PCI ECAM regions. This failure will be silent when running
libvirt, as the console in that situation is a PCI device.
In this configuration, the kernel maps the whole ECAM, which QEMU sets up
for 256 buses, even when maybe only seven buses are in use. Each bus uses
1M of ECAM space, and ioremap() adds an additional guard page between
allocations. The kernel vmap allocator will align these regions to 512K,
resulting in each mapping eating 1.5M of vmalloc space. This means we need
384M of vmalloc space just to map all of these, which is very wasteful of
resources.
Fix this by only mapping the ECAM for buses we are going to be using. In
my setups, this is around seven buses in most guests, which is 10.5M of
vmalloc space - way smaller than the 384M that would otherwise be required.
This also means that the kernel can boot without forcing extra RAM into
highmem with the vmalloc= argument, or decreasing the virtual RAM available
to the guest.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/E1lhCAV-0002yb-50@rmk-PC.armlinux.org.uk
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Downstream Port Containment (PCIe r5.0, sec. 6.2.10) disables the link upon
an error and attempts to re-enable it when instructed by the DPC driver.
A slot which is both DPC- and hotplug-capable is currently powered off by
pciehp once DPC is triggered (due to the link change) and powered back up
on successful recovery. That's undesirable, the slot should remain powered
so the hotplugged device remains bound to its driver. DPC notifies the
driver of the error and of successful recovery in pcie_do_recovery() and
the driver may then restore the device to working state.
Moreover, Sinan points out that turning off slot power by pciehp may foil
recovery by DPC: Power off/on is a cold reset concurrently to DPC's warm
reset. Sathyanarayanan reports extended delays or failure in link
retraining by DPC if pciehp brings down the slot.
Fix by detecting whether a Link Down event is caused by DPC and awaiting
recovery if so. On successful recovery, ignore both the Link Down and the
subsequent Link Up event.
Afterwards, check whether the link is down to detect surprise-removal or
another DPC event immediately after DPC recovery. Ensure that the
corresponding DLLSC event is not ignored by synthesizing it and invoking
irq_wake_thread() to trigger a re-run of pciehp_ist().
The IRQ threads of the hotplug and DPC drivers, pciehp_ist() and
dpc_handler(), race against each other. If pciehp is faster than DPC, it
will wait until DPC recovery completes.
Recovery consists of two steps: The first step (waiting for link
disablement) is recognizable by pciehp through a set DPC Trigger Status
bit. The second step (waiting for link retraining) is recognizable through
a newly introduced PCI_DPC_RECOVERING flag.
If DPC is faster than pciehp, neither of the two flags will be set and
pciehp may glean the recovery status from the new PCI_DPC_RECOVERED flag.
The flag is zero if DPC didn't occur at all, hence DLLSC events are not
ignored by default.
pciehp waits up to 4 seconds before assuming that DPC recovery failed and
bringing down the slot. This timeout is not taken from the spec (it
doesn't mandate one) but based on a report from Yicong Yang that DPC may
take a bit more than 3 seconds on HiSilicon's Kunpeng platform.
The timeout is necessary because the DPC Trigger Status bit may never
clear: On Root Ports which support RP Extensions for DPC, the DPC driver
polls the DPC RP Busy bit for up to 1 second before giving up on DPC
recovery. Without the timeout, pciehp would then wait indefinitely for DPC
to complete.
This commit draws inspiration from previous attempts to synchronize DPC
with pciehp:
By Sinan Kaya, August 2018:
https://lore.kernel.org/linux-pci/20180818065126.77912-1-okaya@kernel.org/
By Ethan Zhao, October 2020:
https://lore.kernel.org/linux-pci/20201007113158.48933-1-haifeng.zhao@intel.com/
By Kuppuswamy Sathyanarayanan, March 2021:
https://lore.kernel.org/linux-pci/59cb30f5e5ac6d65427ceaadf1012b2ba8dbf66c.1615606143.git.sathyanarayanan.kuppuswamy@linux.intel.com/
Link: https://lore.kernel.org/r/0be565d97438fe2a6d57354b3aa4e8626952a00b.1619857124.git.lukas@wunner.de
Reported-by: Sinan Kaya <okaya@kernel.org>
Reported-by: Ethan Zhao <haifeng.zhao@intel.com>
Reported-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Tested-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Tested-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Keith Busch <kbusch@kernel.org>
Merge __calc_map_type_and_dist() and calc_map_type_and_dist_warn() into
calc_map_type_and_dist() to simplify the code a bit. This now means we add
the devfn strings to the acs_buf unconditionally even if the buffer is not
printed, but that is not a lot of overhead and keeps the code much simpler.
Link: https://lore.kernel.org/r/20210614055310.3960791-1-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmDGe+4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG/IUH/iyHVulAtAhL9bnR
qL4M1kWfcG1sKS2TzGRZzo6YiUABf89vFP90r4sKxG3AKrb8YkTwmJr8B/sWwcsv
PpKkXXTobbDfpSrsXGEapBkQOE7h2w739XeXyBLRPkoCR4UrEFn68TV2rLjMLBPS
/EIZkonXLWzzWalgKDP4wSJ7GaQxi3LMx3dGAvbFArEGZ1mPHNlgWy2VokFY/yBf
qh1EZ5rugysc78JCpTqfTf3fUPK2idQW5gtHSMbyESrWwJ/3XXL9o1ET3JWURYf1
b0FgVztzddwgULoIGWLxDH5WWts3l54sjBLj0yrLUlnGKA5FjrZb12g9PdhdywuY
/8KfjeE=
=JfJm
-----END PGP SIGNATURE-----
Merge tag 'v5.13-rc6' into usb-next
We want the usb fixes in here as well, and this resolves some merge
issues with:
drivers/usb/dwc3/debugfs.c
drivers/usb/dwc3/gadget.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to use upstream_bridge_distance_warn() from a dma_map function, it
must not sleep. However, pci_get_slot() takes the pci_bus_sem so it might
sleep.
In order to avoid this, try to get the host bridge's device from the first
element in the device list. It should be impossible for the host bridge's
device to go away while references are held on child devices, so the first
element should not be able to change and, thus, this should be safe.
Introduce a static function called pci_host_bridge_dev() to obtain the host
bridge's root device.
Link: https://lore.kernel.org/r/20210610160609.28447-7-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
All callers of pci_p2pdma_map_type() have a struct dev_pgmap and a struct
device (of the client doing the DMA transfer). Thus move the conversion to
struct pci_devs for the provider and client into this function.
Link: https://lore.kernel.org/r/20210610160609.28447-6-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If the host bridge is not in the whitelist print a warning in the
calc_map_type_and_dist_warn() path detailing the vendor and device IDs that
would need to be added to the whitelist.
Suggested-by: Don Dutile <ddutile@redhat.com>
Link: https://lore.kernel.org/r/20210610160609.28447-5-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Instead of using an int for the return value of this function, use the
correct enum pci_p2pdma_map_type.
Link: https://lore.kernel.org/r/20210610160609.28447-4-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In order to call the calc_map_type_and_dist_warn() function from a dma_map
operation, the function must not sleep. The only reason it sleeps is to
allocate memory for the seq_buf to print a verbose warning telling the user
how to disable ACS for that path.
Instead of allocating the memory with kmalloc(), allocate a smaller buffer
on the stack. A 128 byte buffer is enough to print 10 PCI device names. A
system with 10 bridge ports between two devices that have ACS enabled would
be unusually large, so this should still be a reasonable limit.
This also cleans up the awkward (and broken) return with -ENOMEM which
contradicts the return type and the caller was not prepared for.
Link: https://lore.kernel.org/r/20210610160609.28447-3-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The function upstream_bridge_distance() has evolved such that its name is
no longer entirely reflective of what the function does. It not only
calculates the distance between two peers but also calculates how the DMA
addresses for those two peers should be mapped.
Rename it to calc_map_type_and_dist() and rework the documentation to
better describe the two pieces of information the function returns.
[bhelgaas: tweak comment wording]
Link: https://lore.kernel.org/r/20210610160609.28447-2-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Be more verbose to disambiguate the error case when trying to configure
SR-IOV with no driver bound vs. a driver that does not implement the
.sriov_configure() callback.
Link: https://lore.kernel.org/r/20210327175140.682708-1-mdf@kernel.org
Reported-by: Brian Foley <bpfoley@google.com>
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
On Macbook 2013, resuming from suspend-to-idle or standby resulted in the
external monitor no longer being detected, a stacktrace, and errors like
this in dmesg:
pcieport 0000:06:00.0: can't change power state from D3hot to D0 (config space inaccessible)
The reason is that we know how to turn power to the Thunderbolt controller
*off* via the SXIO/SXFP/SXLF methods, but we don't know how to turn power
back on. We have to rely on firmware to turn the power back on.
When going to the "suspend-to-idle" or "standby" system sleep states,
firmware is not involved either on the suspend side or the resume side, so
we can't use SXIO/SXFP/SXLF to turn the power off.
Skip SXIO/SXFP/SXLF when firmware isn't involved in suspend, e.g., when
we're going to the "suspend-to-idle" or "standby" system sleep states.
Fixes: 1df5172c5c ("PCI: Suspend/resume quirks for Apple thunderbolt")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=212767
Link: https://lore.kernel.org/r/20210520235501.917397-1-Hi-Angel@yandex.ru
Signed-off-by: Konstantin Kharlamov <Hi-Angel@yandex.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org
Previously, when the value of the "devspec" sysfs attribute was read from
the user space there was no newline present, and utilities such as "cat"
wouldn't display the result of the read correctly.
Append a newline character in the show() function to match other "devspec"
attributes.
Link: https://lore.kernel.org/r/20210603000112.703037-5-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
The value of the "resource_alignment" can be specified using a kernel
command-line argument ("pci=resource_alignment=") or through the
corresponding sysfs attribute under the /sys/bus/pci path.
Previously, when the value was set via the kernel command-line argument,
and then subsequently accessed through sysfs attribute, the value read back
was not correct:
# grep -oE 'pci=resource_alignment.+' /proc/cmdline
pci=resource_alignment=20@00:1f.2
# cat /sys/bus/pci/resource_alignment
20@00:1f.
This was also true when the value was set through the sysfs attribute
without including a trailing newline:
# echo -n 20@00:1f.2 > /sys/bus/pci/resource_alignment
# cat /sys/bus/pci/resource_alignment
20@00:1f.
When it was set through the sysfs attribute *including* a newline,
reading it back worked as intended:
# echo 20@00:1f.2 > /sys/bus/pci/resource_alignment
# cat /sys/bus/pci/resource_alignment
20@00:1f.2
To fix this inconsistency, append a trailing newline in the show() function
and strip the trailing line in the store() function if one is present.
Also, allow for the value previously set using either a command-line
argument or through the sysfs object to be cleared at run-time.
[bhelgaas: fold in kfree fix from
https://lore.kernel.org/linux-pci/20210604133230.983956-4-kw@linux.com]
Fixes: e499081da1 ("PCI: Force trailing new line to resource_alignment_param in sysfs")
Link: https://lore.kernel.org/r/20210603000112.703037-4-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
The sysfs_emit() and sysfs_emit_at() functions were introduced to make
it less ambiguous which function is preferred when writing to the output
buffer in a device attribute's "show" callback [1].
Convert the PCI sysfs object "show" functions from sprintf(), snprintf()
and scnprintf() to sysfs_emit() and sysfs_emit_at() accordingly, as the
latter is aware of the PAGE_SIZE buffer and correctly returns the number
of bytes written into the buffer.
No functional change intended.
[1] Documentation/filesystems/sysfs.rst
Related commit: ad025f8e46 ("PCI/sysfs: Use sysfs_emit() and
sysfs_emit_at() in "show" functions").
Link: https://lore.kernel.org/r/20210603000112.703037-2-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
scnprintf() returns the number of bytes written into the buffer. Change
dsm_label_utf16s_to_utf8s() to do the same. Rely on those values instead
of using strlen() to compute the buffer length.
No functional change intended.
[bhelgaas: reorder patch in series, len++ to include newline added by
dsm_label_utf16s_to_utf8s(), commit log]
Link: https://lore.kernel.org/r/20210603000112.703037-3-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
"utf16s_to_utf8s(..., buf, PAGE_SIZE)" puts up to PAGE_SIZE bytes into
"buf" and returns the number of bytes it actually put there. If it wrote
PAGE_SIZE bytes, the newline added by dsm_label_utf16s_to_utf8s() would
overrun "buf".
Reduce the size available for utf16s_to_utf8s() to use so there is always
space for the newline.
[bhelgaas: reorder patch in series, commit log]
Fixes: 6058989bad ("PCI: Export ACPI _DSM provided firmware instance number and string name to sysfs")
Link: https://lore.kernel.org/r/20210603000112.703037-7-kw@linux.com
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
With the new method of flushing/stopping the workqueue before doing bus
removal, the old mechanism of using refcount and wait for completion
is no longer needed. Remove those dead code.
Link: https://lore.kernel.org/r/1620806809-31055-1-git-send-email-longli@linuxonhyperv.com
Signed-off-by: Long Li <longli@microsoft.com>
[lorenzo.pieralisi@arm.com: Reworded subject]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
On removing the device, any work item (hv_pci_devices_present() or
hv_pci_eject_device()) scheduled on workqueue hbus->wq may still be running
and race with hv_pci_remove().
This can happen because the host may send PCI_EJECT or PCI_BUS_RELATIONS(2)
and decide to rescind the channel immediately after that.
Fix this by flushing/destroying the workqueue of hbus before doing hbus remove.
Link: https://lore.kernel.org/r/1620806800-30983-1-git-send-email-longli@linuxonhyperv.com
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
When devm_ioremap_resource() fails, a clear enough error message will be
printed by its subfunction __devm_ioremap_resource(). The error
information contains the device name, failure cause, and possibly resource
information.
Therefore, remove the error printing here to simplify code and reduce the
binary size.
Link: https://lore.kernel.org/r/20210511122453.6052-1-thunder.leizhen@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
PCI_IOSIZE is defined in mach-loongson64/spaces.h, so change the name
of the PCI_* macros in pci-ftpci100.c to use FTPCI_* so that they are
more localized and won't conflict with other drivers or arches.
../drivers/pci/controller/pci-ftpci100.c:37: warning: "PCI_IOSIZE" redefined
37 | #define PCI_IOSIZE 0x00
|
In file included from ../arch/mips/include/asm/addrspace.h:13,
... from ../drivers/pci/controller/pci-ftpci100.c:15:
arch/mips/include/asm/mach-loongson64/spaces.h:11: note: this is the location of the previous definition
11 | #define PCI_IOSIZE SZ_16M
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210517234117.3660-1-rdunlap@infradead.org
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Krzysztof Wilczyński <kw@linux.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@vger.kernel.org
The PCIe host controller driver for Layerscape 4th generation SoC was
added in the commit d29ad70a81 ("PCI: mobiveil: Add PCIe Gen4 RC
driver for Layerscape SoCs").
At this time two static functions were introduced that appear to
currently have no users. Since nothing is using neither of these
functions at the moment they can be safely removed.
This resolves the following build time warnings:
drivers/pci/controller/mobiveil/pcie-layerscape-gen4.c:45:19: warning: unused function 'ls_pcie_g4_lut_readl' [-Wunused-function]
drivers/pci/controller/mobiveil/pcie-layerscape-gen4.c:50:20: warning: unused function 'ls_pcie_g4_lut_writel' [-Wunused-function]
Link: https://lore.kernel.org/r/20210510023032.3063932-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The struct event_descs does not have any users outside the
pcie-microchip-host.c file, and has no previous declaration,
thus it can be made static.
This resolves the following sparse warning:
drivers/pci/controller/pcie-microchip-host.c:352:3: warning: symbol 'event_descs' was not declared. Should it be static?
Link: https://lore.kernel.org/r/20210509041932.560340-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Commit 6279504141 ("PCI: enhance physical slot debug information") added
a debug print on releasing the PCI slot and another message on destroying
it. There is however no debug print on releasing the PCI device structure
itself and even with closely looking at the kernel log during hotplug
testing, I overlooked several missing pci_dev_put() calls for way too long.
Add a debug print in pci_release_dev() making it much easier to spot when
the PCI device structure is not released when it is supposed to be.
Link: https://lore.kernel.org/r/20210311132312.2882425-1-schnelle@linux.ibm.com
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We use format domain🚌slot.function when printing PCI device. Use
consistent format in AER messages.
[bhelgaas: also drop "AER recover:" prefix since we already have an "AER:"
prefix from pr_fmt()]
Link: https://lore.kernel.org/r/1617015721-51701-1-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
A PCI device is "external_facing" if it's a Root Port with the ACPI
"ExternalFacingPort" property or if it has the DT "external-facing"
property. We consider everything downstream from such a device to
be removable by user.
We're mainly concerned with consumer platforms with user accessible
Thunderbolt ports that are vulnerable to DMA attacks, and we expect those
ports to be identified by firmware as "ExternalFacingPort". Devices in
traditional hotplug slots can technically be removed, but the expectation
is that unless the port is marked with "ExternalFacingPort", such devices
are less accessible to user / may not be removed by end user, and thus not
exposed as "removable" to userspace.
This can be used to implement userspace policies tailored for
user removable devices. Eg usage:
https://chromium-review.googlesource.com/c/chromiumos/platform2/+/2591812https://chromium-review.googlesource.com/c/chromiumos/platform2/+/2795038
(code uses such an attribute to remove external PCI devices or disable
features on them as needed by the policy desired)
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rajat Jain <rajatja@google.com>
Link: https://lore.kernel.org/r/20210524171812.18095-2-rajatja@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 9ec37efb87 ("PCI/MSI: Make pci_host_common_probe() declare
its reliance on MSI domains"), platforms that rely on the "msi-map"
device-tree property don't get MSIs anymore.
On the Arm Fast Model for example [1], the host bridge doesn't have a
"msi-parent" property since it doesn't itself generate MSIs, and so doesn't
get a MSI domain. It has an "msi-map" property instead to describe MSI
controllers of child devices. As a result, due to the new msi_domain check
in pci_register_host_bridge(), the whole bus gets PCI_BUS_FLAGS_NO_MSI.
Check whether the root complex has an "msi-map" property before giving
up on MSIs.
[1] arch/arm64/boot/dts/arm/fvp-base-revc.dts
Fixes: 9ec37efb87 ("PCI/MSI: Make pci_host_common_probe() declare its reliance on MSI domains")
Link: https://lore.kernel.org/r/20210510173129.750496-1-jean-philippe@linaro.org
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Marc Zyngier <maz@kernel.org>
pcie_flr() starts a Function Level Reset (FLR), waits 100ms (the maximum
time allowed for FLR completion by PCIe r5.0, sec 6.6.2), and waits for the
FLR to complete. It assumes the FLR is complete when a config read returns
valid data.
When we do an FLR on several Huawei Intelligent NIC VFs at the same time,
firmware on the NIC processes them serially. The VF may respond to config
reads before the firmware has completed its reset processing. If we bind a
driver to the VF (e.g., by assigning the VF to a virtual machine) in the
interval between the successful config read and completion of the firmware
reset processing, the NIC VF driver may fail to load.
Prevent this driver failure by waiting for the NIC firmware to complete its
reset processing. Not all NIC firmware supports this feature.
[bhelgaas: commit log]
Link: https://support.huawei.com/enterprise/en/doc/EDOC1100063073/87950645/vm-oss-occasionally-fail-to-load-the-in200-driver-when-the-vf-performs-flr
Link: https://lore.kernel.org/r/20210414132301.1793-1-chiqijun@huawei.com
Signed-off-by: Chiqijun <chiqijun@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
pci_parent_bus_reset() resets a device by performing a Secondary Bus Reset
on a PCI-to-PCI bridge leading to the device.
pci_dev_reset_slot_function() does the same, except that it uses a hotplug
driver to keep the reset from looking like a hot-remove followed by a
hot-add.
Add a pci_reset_bus_function() wrapper, which attempts the hotplug driver
slot reset and falls back to the parent bus reset if that fails. This
provides a single interface for performing a Secondary Bus Reset.
[bhelgaas: commit log, don't expose yet]
Suggested-by: Alex Williamson <alex.williamson@redhat.com>
Link: https://lore.kernel.org/r/20210323100625.0021a943@omen.home.shazbot.org/
Link: https://lore.kernel.org/r/20210408182328.12323-1-raphael.norwitz@nutanix.com
Signed-off-by: Amey Narkhede <ameynarkhede03@gmail.com>
Signed-off-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
- add support for system call stack randomization.
- handle stale PCI deconfiguration events.
- couple of defconfig updates.
- some fixes and cleanups.
-----BEGIN PGP SIGNATURE-----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=C1HZ
-----END PGP SIGNATURE-----
Merge tag 's390-5.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Heiko Carstens:
- add support for system call stack randomization
- handle stale PCI deconfiguration events
- couple of defconfig updates
- some fixes and cleanups
* tag 's390-5.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: fix detection of vector enhancements facility 1 vs. vector packed decimal facility
s390/entry: add support for syscall stack randomization
s390/configs: change CONFIG_VIRTIO_CONSOLE to "m"
s390/cio: remove invalid condition on IO_SCH_UNREG
s390/cpumf: remove call to perf_event_update_userpage
s390/cpumf: move counter set size calculation to common place
s390/cpumf: beautify if-then-else indentation
s390/configs: enable CONFIG_PCI_IOV
s390/pci: handle stale deconfiguration events
s390/pci: rename zpci_configure_device()
New drivers/devices
- Support for QCOM SM8150 GPI DMA
Updates:
- Big pile of idxd updates including support for performance monitoring
- Support in dw-edma for interleaved dma
- Support for synchronize() in Xilinx driver
-----BEGIN PGP SIGNATURE-----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=Jjb4
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine updates from Vinod Koul:
"New drivers/devices:
- Support for QCOM SM8150 GPI DMA
Updates:
- Big pile of idxd updates including support for performance
monitoring
- Support in dw-edma for interleaved dma
- Support for synchronize() in Xilinx driver"
* tag 'dmaengine-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (42 commits)
dmaengine: idxd: Enable IDXD performance monitor support
dmaengine: idxd: Add IDXD performance monitor support
dmaengine: idxd: remove MSIX masking for interrupt handlers
dmaengine: idxd: device cmd should use dedicated lock
dmaengine: idxd: support reporting of halt interrupt
dmaengine: idxd: enable SVA feature for IOMMU
dmaengine: idxd: convert sprintf() to sysfs_emit() for all usages
dmaengine: idxd: add interrupt handle request and release support
dmaengine: idxd: add support for readonly config mode
dmaengine: idxd: add percpu_ref to descriptor submission path
dmaengine: idxd: remove detection of device type
dmaengine: idxd: iax bus removal
dmaengine: idxd: fix cdev setup and free device lifetime issues
dmaengine: idxd: fix group conf_dev lifetime
dmaengine: idxd: fix engine conf_dev lifetime
dmaengine: idxd: fix wq conf_dev 'struct device' lifetime
dmaengine: idxd: fix idxd conf_dev 'struct device' lifetime
dmaengine: idxd: use ida for device instance enumeration
dmaengine: idxd: removal of pcim managed mmio mapping
dmaengine: idxd: cleanup pci interrupt vector allocation management
...
Pull swiotlb updates from Konrad Rzeszutek Wilk:
"Christoph Hellwig has taken a cleaver and trimmed off the not-needed
code and nicely folded duplicate code in the generic framework.
This lays the groundwork for more work to add extra DMA-backend-ish in
the future. Along with that some bug-fixes to make this a nice working
package"
* 'stable/for-linus-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb:
swiotlb: don't override user specified size in swiotlb_adjust_size
swiotlb: Fix the type of index
swiotlb: Make SWIOTLB_NO_FORCE perform no allocation
ARM: Qualify enabling of swiotlb_init()
swiotlb: remove swiotlb_nr_tbl
swiotlb: dynamically allocate io_tlb_default_mem
swiotlb: move global variables into a new io_tlb_mem structure
xen-swiotlb: remove the unused size argument from xen_swiotlb_fixup
xen-swiotlb: split xen_swiotlb_init
swiotlb: lift the double initialization protection from xen-swiotlb
xen-swiotlb: remove xen_io_tlb_start and xen_io_tlb_nslabs
xen-swiotlb: remove xen_set_nslabs
xen-swiotlb: use io_tlb_end in xen_swiotlb_dma_supported
xen-swiotlb: use is_swiotlb_buffer in is_xen_swiotlb_buffer
swiotlb: split swiotlb_tbl_sync_single
swiotlb: move orig addr and size validation into swiotlb_bounce
swiotlb: remove the alloc_size parameter to swiotlb_tbl_unmap_single
powerpc/svm: stop using io_tlb_start
- Add reset_control_rearm() stub for !CONFIG_RESET_CONTROLLER (Jim Quinlan)
- Fix use of BCM7216 reset controller (Jim Quinlan)
- Use reset/rearm for Broadcom STB pulse reset instead of deassert/assert
(Jim Quinlan)
* pci/brcmstb:
PCI: brcmstb: Use reset/rearm instead of deassert/assert
ata: ahci_brcm: Fix use of BCM7216 reset controller
reset: add missing empty function reset_control_rearm()
- Convert tegra to MSI domains (Marc Zyngier)
- Use rcar controller address as MSI doorbell instead of allocating a page
(Marc Zyngier)
- Convert rcar to MSI domains (Marc Zyngier)
- Use xilinx port structure as MSI doorbell instead of allocating a page
(Marc Zyngier)
- Convert xilinx to MSI domains (Marc Zyngier)
- Remove unused Hyper-V msi_controller structure (Marc Zyngier)
- Remove unused PCI core msi_controller support (Marc Zyngier)
- Remove struct msi_controller (Marc Zyngier)
- Remove unused default_teardown_msi_irqs() (Marc Zyngier)
- Let host bridges declare their reliance on MSI domains (Marc Zyngier)
- Make pci_host_common_probe() declare its reliance on MSI domains (Marc
Zyngier)
- Advertise mediatek lack of built-in MSI handling (Thomas Gleixner)
- Document ways of ending up with NO_MSI (Marc Zyngier)
- Refactor HT advertising of NO_MSI flag (Marc Zyngier)
* remotes/lorenzo/pci/msi:
PCI: Refactor HT advertising of NO_MSI flag
PCI/MSI: Document the various ways of ending up with NO_MSI
PCI: mediatek: Advertise lack of built-in MSI handling
PCI/MSI: Make pci_host_common_probe() declare its reliance on MSI domains
PCI/MSI: Let PCI host bridges declare their reliance on MSI domains
PCI/MSI: Kill default_teardown_msi_irqs()
PCI/MSI: Kill msi_controller structure
PCI/MSI: Drop use of msi_controller from core code
PCI: hv: Drop msi_controller structure
PCI: xilinx: Convert to MSI domains
PCI: xilinx: Don't allocate extra memory for the MSI capture address
PCI: rcar: Convert to MSI domains
PCI: rcar: Don't allocate extra memory for the MSI capture address
PCI: tegra: Convert to MSI domains
- Program IRTE with Requester ID of VMD endpoint, not child device (Jon
Derrick)
- Disable VMD MSI-X remapping when possible so children can use more MSI-X
vectors (Jon Derrick)
* remotes/lorenzo/pci/vmd:
PCI: vmd: Disable MSI-X remapping when possible
iommu/vt-d: Use Real PCI DMA device for IRTE
- Make several microchip symbols static (Wei Yongjun)
- Drop redundant dev_err() for platform_get_irq() errors (Krzysztof
Wilczyński)
* remotes/lorenzo/pci/microchip:
PCI: microchip: Remove dev_err() when handing an error from platform_get_irq()
PCI: microchip: Make some symbols static
- Configure FC and FTS for functions other than 0 (Ryder Lee)
- Add missing MODULE_DEVICE_TABLE (Qiheng Lin)
- Add YAML schema for MediaTek (Jianjun Wang)
- Export pci_pio_to_address() for module use (Jianjun Wang)
- Add MediaTek MT8192 PCIe controller driver (Jianjun Wang)
- Add MediaTek MT8192 INTx support (Jianjun Wang)
- Add MediaTek MT8192 MSI support (Jianjun Wang)
- Add MediaTek MT8192 system power management support (Jianjun Wang)
* remotes/lorenzo/pci/mediatek:
MAINTAINERS: Add Jianjun Wang as MediaTek PCI co-maintainer
PCI: mediatek-gen3: Add system PM support
PCI: mediatek-gen3: Add MSI support
PCI: mediatek-gen3: Add INTx support
PCI: mediatek-gen3: Add MediaTek Gen3 driver for MT8192
PCI: Export pci_pio_to_address() for module use
dt-bindings: PCI: mediatek-gen3: Add YAML schema
PCI: mediatek: Add missing MODULE_DEVICE_TABLE
PCI: mediatek: Configure FC and FTS for functions other than 0
- Return zero for success of iproc_msi_irq_domain_alloc() (Pali Rohár)
* remotes/lorenzo/pci/iproc:
PCI: iproc: Fix return value of iproc_msi_irq_domain_alloc()
- Use generic config accessors for TI AM65x (K3) to fix regression (Kishon
Vijay Abraham I)
- Move MSI Receiver init to dw_pcie_host_init() so it is re-initialized
along with the RC in resume (Jisheng Zhang)
- Remove unused pcie_app_rd() (Jiapeng Chong)
- Move iATU detection earlier to fix regression (Hou Zhiqiang)
* remotes/lorenzo/pci/dwc:
PCI: dwc: Move iATU detection earlier
PCI: dwc/intel-gw: Remove unused function
PCI: dwc: Move dw_pcie_msi_init() to dw_pcie_setup_rc()
PCI: keystone: Let AM65 use the pci_ops defined in pcie-designware-host.c
- Add DT binding and TI j721e support for refclk to PCIe connector (Kishon
Vijay Abraham I)
- Add host mode and endpoint mode DT bindings for TI AM64 SoC (Kishon Vijay
Abraham I)
* remotes/lorenzo/pci/cadence:
PCI: j721e: Add support to provide refclk to PCIe connector
dt-bindings: PCI: ti,j721e: Add endpoint mode dt-bindings for TI's AM64 SoC
dt-bindings: PCI: ti,j721e: Add host mode dt-bindings for TI's AM64 SoC
dt-bindings: PCI: ti,j721e: Add binding to represent refclk to the connector
- Increase delay after FLR to work around Intel DC P4510 NVMe erratum
(Raphael Norwitz)
* pci/virtualization:
PCI: Delay after FLR of Intel DC P4510 NVMe
Add driver for the SiFive FU740 PCIe host controller.
This controller is based on the DesignWare PCIe core.
Co-developed-by: Henry Styles <hes@sifive.com>
Co-developed-by: Erik Danie <erik.danie@sifive.com>
Co-developed-by: Greentime Hu <greentime.hu@sifive.com>
Link: https://lore.kernel.org/r/20210504105940.100004-6-greentime.hu@sifive.com
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Henry Styles <hes@sifive.com>
Signed-off-by: Erik Danie <erik.danie@sifive.com>
Signed-off-by: Greentime Hu <greentime.hu@sifive.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The Broadcom STB PCIe RC uses a reset control "rescal" for certain chips.
The "rescal" implements a "pulse reset" so using assert/deassert is wrong
for this device. Instead, we use reset/rearm. We need to use rearm so
that we can reset it after a suspend/resume cycle; w/o using "rearm", the
"rescal" device will only ever fire once.
Of course for suspend/resume to work we also need to put the reset/rearm
calls in the suspend and resume routines.
Fixes: 740d6c3708 ("PCI: brcmstb: Add control of rescal reset")
Link: https://lore.kernel.org/r/20210430152156.21162-4-jim2101024@gmail.com
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Only SRDT tag is the end tag, and no caller is interested in it. This
allows to remove all SRDT tag handling.
Link: https://lore.kernel.org/r/3f63f06f-734f-8fff-9518-27fe1faf903d@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
All callers pass 0 as offset. Therefore remove the parameter and use a
fixed offset 0 in pci_vpd_find_tag().
Link: https://lore.kernel.org/r/f62e6e19-5423-2ead-b2bd-62844b23ef8f@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_init_capabilities() is the only caller and doesn't use the return
value. So let's change the return type to void.
Link: https://lore.kernel.org/r/663ec440-8375-1459-ddb4-98ea76e75917@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Realtek RTL8169/8168/8125 NIC families indicate VPD capability and an
optional VPD EEPROM can be connected via I2C/SPI. However I haven't seen
any card or system with such a VPD EEPROM yet. The missing EEPROM causes
the following warning whenever e.g. lscpi -vv is executed.
invalid short VPD tag 00 at offset 01
The warning confuses users, and I think we should handle the situation more
gently. Therefore, if first VPD byte is read as 0x00, assume a missing
optional VPD PROM and replace the warning with a more descriptive message
at info level.
[bhelgaas: fix pre-existing whitespace]
Link: https://lore.kernel.org/r/ccbc11f1-4dbb-e2c8-d0ea-559e06d4c340@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
24a1720a08 ("cxgb4: collect serial config version from register") removed
the only usage of pci_set_vpd_size(). If a device needs to override the
auto-detected VPD size, then this can be done with a PCI quirk, as is done
for Chelsio devices. There's no need to allow drivers to change the VPD
size.
Remove pci_set_vpd_size().
[bhelgaas: squash in Arnd's fix for "'pci_vpd_set_size' defined but not
used" from
https://lore.kernel.org/r/20210421140334.3847155-1-arnd@kernel.org]
Link: https://lore.kernel.org/r/47d86e52-9bcf-7da7-1edb-0d988a7a82ab@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
This is a shim around vunmap_range, get rid of it.
Move the main API comment from the _noflush variant to the normal
variant, and make _noflush internal to mm/.
[npiggin@gmail.com: fix nommu builds and a comment bug per sfr]
Link: https://lkml.kernel.org/r/1617292598.m6g0knx24s.astroid@bobo.none
[akpm@linux-foundation.org: move vunmap_range_noflush() stub inside !CONFIG_MMU, not !CONFIG_NUMA]
[npiggin@gmail.com: fix nommu builds]
Link: https://lkml.kernel.org/r/1617292497.o1uhq5ipxp.astroid@bobo.none
Link: https://lkml.kernel.org/r/20210322021806.892164-5-npiggin@gmail.com
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Cédric Le Goater <clg@kaod.org>
Cc: Uladzislau Rezki <urezki@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With zpci_configure_device() now always called on a device that has
already been configured on the platform level its name has become
misleading. Rename it to zpci_scan_configured_device() to signify that
the function now only handles the correct scanning of a newly configured
PCI function taking care of the special handling necessary for function
0 and functions parked waiting for a PCI bus that can't be created
without first seeing function 0.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to
walk all map elements in a more robust and easier to verify
fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF
on s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices
which don't need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability
on next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is
slow in reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take
place correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP
packets before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used
to define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
-independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and
bnxt support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP
which define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay
for packets sampled from switch HW (and corresponding egress
and policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP
forwarding, bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface
to distribute MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x -
11-port Ethernet switch with 8x 1-Gigabit Ethernet
and 3x 10-Gigabit interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365
and BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack,
matching on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode
changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=vcbA
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to walk
all map elements in a more robust and easier to verify fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF on
s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices which don't
need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability on
next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is slow in
reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take place
correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP packets
before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used to
define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and bnxt
support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP which
define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay for
packets sampled from switch HW (and corresponding egress and
policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP forwarding,
bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface to distribute
MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x - 11-port
Ethernet switch with 8x 1-Gigabit Ethernet and 3x 10-Gigabit
interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365 and
BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack, matching
on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes"
* tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2451 commits)
net: selftest: fix build issue if INET is disabled
net: netrom: nr_in: Remove redundant assignment to ns
net: tun: Remove redundant assignment to ret
net: phy: marvell: add downshift support for M88E1240
net: dsa: ksz: Make reg_mib_cnt a u8 as it never exceeds 255
net/sched: act_ct: Remove redundant ct get and check
icmp: standardize naming of RFC 8335 PROBE constants
bpf, selftests: Update array map tests for per-cpu batched ops
bpf: Add batched ops support for percpu array
bpf: Implement formatted output helpers with bstr_printf
seq_file: Add a seq_bprintf function
sfc: adjust efx->xdp_tx_queue_count with the real number of initialized queues
net:nfc:digital: Fix a double free in digital_tg_recv_dep_req
net: fix a concurrency bug in l2tp_tunnel_register()
net/smc: Remove redundant assignment to rc
mpls: Remove redundant assignment to err
llc2: Remove redundant assignment to rc
net/tls: Remove redundant initialization of record
rds: Remove redundant assignment to nr_sig
dt-bindings: net: mdio-gpio: add compatible for microchip,mdio-smi0
...
Add suspend_noirq and resume_noirq callback functions to implement PM
system suspend and resume hooks for the MediaTek Gen3 PCIe controller.
When the system suspends, trigger the PCIe link to enter the L2 state
and pull down the PERST# pin, gating the clocks of the MAC layer, and
then power-off the physical layer to provide power-saving.
When the system resumes, the PCIe link should be re-established and the
related control register values should be restored.
Link: https://lore.kernel.org/r/20210420061723.989-7-jianjun.wang@mediatek.com
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
Add INTx support for MediaTek Gen3 PCIe controller.
Link: https://lore.kernel.org/r/20210420061723.989-5-jianjun.wang@mediatek.com
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
MediaTek's PCIe host controller has three generation HWs, the new
generation HW is an individual bridge, it supports Gen3 speed and
compatible with Gen2, Gen1 speed.
Add support for new Gen3 controller which can be found on MT8192.
Link: https://lore.kernel.org/r/20210420061723.989-4-jianjun.wang@mediatek.com
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
dw_pcie_ep_init() depends on the detected iATU region numbers to allocate
the in/outbound window management bitmap. It fails after 281f1f99cf
("PCI: dwc: Detect number of iATU windows").
Move the iATU region detection into a new function, move the detection to
the very beginning of dw_pcie_host_init() and dw_pcie_ep_init(). Also
remove it from the dw_pcie_setup(), since it's more like a software
initialization step than hardware setup.
Link: https://lore.kernel.org/r/20210125044803.4310-1-Zhiqiang.Hou@nxp.com
Link: https://lore.kernel.org/linux-pci/20210407131255.702054-1-dmitry.baryshkov@linaro.org
Link: https://lore.kernel.org/r/20210413142219.2301430-1-dmitry.baryshkov@linaro.org
Fixes: 281f1f99cf ("PCI: dwc: Detect number of iATU windows")
Tested-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[DB: moved dw_pcie_iatu_detect to happen after host_init callback]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: stable@vger.kernel.org # v5.11+
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
If the host which makes use of IP's integrated MSI Receiver losts
power during suspend, we need to reinit the RC and MSI Receiver in
resume. But after we move dw_pcie_msi_init() into the core, we have no
API to do so. Usually the dwc users need to call dw_pcie_setup_rc() to
reinit the RC, we can solve this problem by moving dw_pcie_msi_init()
to dw_pcie_setup_rc().
Link: https://lore.kernel.org/r/20210325152604.6e79deba@xhacker.debian
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
The sysfs_emit() and sysfs_emit_at() functions were introduced to make it
less ambiguous which function is preferred when writing to the output
buffer in a device attribute's "show" callback [1].
Convert the PCI sysfs object "show" functions from sprintf(), snprintf()
and scnprintf() to sysfs_emit() and sysfs_emit_at() accordingly, as the
latter is aware of the PAGE_SIZE buffer and correctly returns the number of
bytes written into the buffer.
No functional change intended.
[1] Documentation/filesystems/sysfs.rst
[bhelgaas: drop dsm_label_utf16s_to_utf8s(), link speed/width changes]
Link: https://lore.kernel.org/r/20210416205856.3234481-10-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Collect the smbios_attr_group and acpi_attr_group together in the logical
order. No functional change intended.
[bhelgaas: split to separate patch]
Link: https://lore.kernel.org/r/20210416205856.3234481-6-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Update coding style to reduce distraction. No functional change intended.
[bhelgaas: split to separate patch]
Link: https://lore.kernel.org/r/20210416205856.3234481-6-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The "label", "index", and "acpi_index" sysfs attributes show firmware label
information about the device. If the ACPI Device Name _DSM is implemented
for the device, we have:
label Device name (optional, may be null)
acpi_index Instance number (unique under \_SB scope)
When there is no ACPI _DSM and SMBIOS provides an Onboard Devices structure
for the device, we have:
label Reference Designation, e.g., a silkscreen label
index Device Type Instance
Previously these attributes were dynamically created either by
pci_bus_add_device() or the pci_sysfs_init() initcall, but since they don't
need to be created or removed dynamically, we can use a static attribute so
the device model takes care of addition and removal automatically.
Convert "label", "index", and "acpi_index" to static attributes.
Presence of the ACPI _DSM (device_has_acpi_name()) determines whether the
ACPI information (label, acpi_index) or the SMBIOS information (label,
index) is visible.
[bhelgaas: commit log, split to separate patch, add "pci_dev_" prefix]
Suggested-by: Oliver O'Halloran <oohall@gmail.com>
Link: https://lore.kernel.org/r/20210416205856.3234481-6-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use DEVICE_ATTR*() to simplify definition of the SMBIOS label attributes.
No functional change intended.
Note that dev_attr_smbios_label requires __ATTR() because the "label"
attribute can be exposed via either ACPI or SMBIOS, and we already have the
ACPI label_show() function in this file.
[bhelgaas: split to separate patch]
Link: https://lore.kernel.org/r/20210416205856.3234481-6-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use DEVICE_ATTR*() to simplify definitions of the ACPI label attributes.
No functional change intended.
[bhelgaas: split to separate patch]
Link: https://lore.kernel.org/r/20210416205856.3234481-6-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Rename device_has_dsm() to device_has_acpi_name() to better reflect its
purpose and move it earlier so it's available for a future SMBIOS
.is_visible() function. No functional change intended.
[bhelgaas: split to separate patch]
Link: https://lore.kernel.org/r/20210416205856.3234481-6-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The "vpd" sysfs attribute allows access to Vital Product Data (VPD).
Previously it was dynamically created either by pci_bus_add_device() or the
pci_sysfs_init() initcall, but since it doesn't need to be created or
removed dynamically, we can use a static attribute so the device model
takes care of addition and removal automatically.
Convert "vpd" to a static attribute and use the .is_bin_visible() callback
to check whether the device supports VPD.
Remove pcie_vpd_create_sysfs_dev_files(),
pcie_vpd_remove_sysfs_dev_files(), pci_create_capabilities_sysfs(), and
pci_create_capabilities_sysfs(), which are no longer needed.
[bhelgaas: This is substantially the same as the earlier patch from Heiner
Kallweit <hkallweit1@gmail.com>. I included Krzysztof's change here so all
the "convert to static attribute" changes are together.]
[bhelgaas: rename to vpd_read()/vpd_write() and pci_dev_vpd_attr_group]
Suggested-by: Oliver O'Halloran <oohall@gmail.com>
Based-on: https://lore.kernel.org/r/7703024f-8882-9eec-a122-599871728a89@gmail.com
Based-on-patch-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/20210416205856.3234481-5-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Rename "vpd" attribute accessors so they fit with the BIN_ATTR_RW() macro
usage. Currently there is no BIN_ATTR_ADMIN_RW() that uses 0600
permissions, but if there were, it would likely use "vpd_read()" and
"vpd_write()". No functional change intended.
Extracted from the patch mentioned below by Heiner Kallweit
<hkallweit1@gmail.com>.
Link: https://lore.kernel.org/linux-pci/7703024f-8882-9eec-a122-599871728a89@gmail.com/
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- fix buffer size for in-kernel disassembler for ebpf programs.
- fix two memory leaks in zcrypt driver.
- expose PCI device UID as index, including an indicator if the uid is
unique.
- remove some oprofile leftovers.
- improve stack unwinder tests.
- don't use gcc atomic builtins anymore, just like all other
architectures. Even though I'm sure the current code is ok, I
totally dislike that s390 is the only architecture being special
here; especially considering that there was a lengthly discussion
about this topic and the outcome was not to use the builtins.
Therefore open-code atomic ops again with inline assembly and switch
to gcc builtins as soon as other architectures are doing.
- couple of other changes to atomic and cmpxchg, and use
atomic-instrumented.h for KASAN.
- separate zbus creation, registration, and scanning in our PCI code
which allows for cleaner and easier handling.
- a rather large change to the vfio-ap code to fix circular locking
dependencies when updating crypto masks.
- move QAOB handling from qdio layer down to drivers.
- add CRW inject facility to common I/O layer. This adds debugs files
which allow to generate artificial events from user space for
testing purposes.
- increase SCLP console line length from 80 to 320 characters to avoid
odd wrapped lines.
- add protected virtualization guest and host indication files, which
indicate either that a guest is running in pv mode or if the
hypervisor is capable of starting pv guests.
- various other small fixes and improvements all over the place.
-----BEGIN PGP SIGNATURE-----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=e+mh
-----END PGP SIGNATURE-----
Merge tag 's390-5.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Heiko Carstens:
- fix buffer size for in-kernel disassembler for ebpf programs.
- fix two memory leaks in zcrypt driver.
- expose PCI device UID as index, including an indicator if the uid is
unique.
- remove some oprofile leftovers.
- improve stack unwinder tests.
- don't use gcc atomic builtins anymore, just like all other
architectures. Even though I'm sure the current code is ok, I totally
dislike that s390 is the only architecture being special here;
especially considering that there was a lengthly discussion about
this topic and the outcome was not to use the builtins. Therefore
open-code atomic ops again with inline assembly and switch to gcc
builtins as soon as other architectures are doing.
- couple of other changes to atomic and cmpxchg, and use
atomic-instrumented.h for KASAN.
- separate zbus creation, registration, and scanning in our PCI code
which allows for cleaner and easier handling.
- a rather large change to the vfio-ap code to fix circular locking
dependencies when updating crypto masks.
- move QAOB handling from qdio layer down to drivers.
- add CRW inject facility to common I/O layer. This adds debugs files
which allow to generate artificial events from user space for testing
purposes.
- increase SCLP console line length from 80 to 320 characters to avoid
odd wrapped lines.
- add protected virtualization guest and host indication files, which
indicate either that a guest is running in pv mode or if the
hypervisor is capable of starting pv guests.
- various other small fixes and improvements all over the place.
* tag 's390-5.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (53 commits)
s390/disassembler: increase ebpf disasm buffer size
s390/archrandom: add parameter check for s390_arch_random_generate
s390/zcrypt: fix zcard and zqueue hot-unplug memleak
s390/pci: expose a PCI device's UID as its index
s390/atomic,cmpxchg: always inline __xchg/__cmpxchg
s390/smp: fix do_restart() prototype
s390: get rid of oprofile leftovers
s390/atomic,cmpxchg: make constraints work with old compilers
s390/test_unwind: print test suite start/end info
s390/cmpxchg: use unsigned long values instead of void pointers
s390/test_unwind: add WARN if tests failed
s390/test_unwind: unify error handling paths
s390: update defconfigs
s390/spinlock: use R constraint in inline assembly
s390/atomic,cmpxchg: switch to use atomic-instrumented.h
s390/cmpxchg: get rid of gcc atomic builtins
s390/atomic: get rid of gcc atomic builtins
s390/atomic: use proper constraints
s390/atomic: move remaining inline assemblies to atomic_ops.h
s390/bitops: make bitops only work on longs
...
The "reset" sysfs attribute allows for resetting a PCI function.
Previously it was dynamically created either by pci_bus_add_device() or
the pci_sysfs_init() initcall, but since it doesn't need to be created or
removed dynamically, we can use a static attribute so the device model
takes care of addition and removal automatically.
Convert "reset" to a static attribute and use the .is_visible() callback to
check whether the device supports reset.
Clear reset_fn in pci_stop_dev() instead of pci_remove_capabilities_sysfs()
since we no longer explicitly remove the "reset" sysfs file.
[bhelgaas: commit log]
Suggested-by: Oliver O'Halloran <oohall@gmail.com>
Link: https://lore.kernel.org/r/20210416205856.3234481-4-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The "rom" sysfs attribute allows access to the PCI Option ROM. Previously
it was dynamically created either by pci_bus_add_device() or the
pci_sysfs_init() initcall, but since it doesn't need to be created or
removed dynamically, we can use a static attribute so the device model
takes care of addition and removal automatically.
Convert "rom" to a static attribute and use the .is_bin_visible() callback
to set the correct object size based on the ROM size.
Remove "rom_attr" from the struct pci_dev since it is no longer needed.
This attribute was added in the pre-git era by https://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git/commit/drivers/pci/pci-sysfs.c?id=f6d553444da2
[bhelgaas: commit log]
Suggested-by: Oliver O'Halloran <oohall@gmail.com>
Link: https://lore.kernel.org/r/20210416205856.3234481-3-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The "config" sysfs attribute allows access to either the legacy (PCI and
PCI-X Mode 1) or the extended (PCI-X Mode 2 and PCIe) device configuration
space. Previously it was dynamically created either when a device was
added (for hot-added devices) or via a late_initcall (for devices present
at boot):
pci_bus_add_devices
pci_bus_add_device
pci_create_sysfs_dev_files
if (!sysfs_initialized)
return
sysfs_create_bin_file # for hot-added devices
pci_sysfs_init # late_initcall
sysfs_initialized = 1
for_each_pci_dev(pdev)
pci_create_sysfs_dev_files(pdev) # for devices present at boot
And dynamically removed when the PCI device is stopped and removed:
pci_stop_bus_device
pci_stop_dev
pci_remove_sysfs_dev_files
sysfs_remove_bin_file
This attribute does not need to be created or removed dynamically, so we
can use a static attribute so the device model takes care of addition and
removal automatically.
Convert "config" to a static attribute and use the .is_bin_visible()
callback to set the correct object size (either 256 bytes or 4 KiB) at
runtime.
The pci_sysfs_init() scheme was added in the pre-git era by
https://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git/commit/drivers/pci/pci-sysfs.c?id=f6d553444da2
[bhelgaas: commit log]
Suggested-by: Oliver O'Halloran <oohall@gmail.com>
Link: https://lore.kernel.org/r/CAOSf1CHss03DBSDO4PmTtMp0tCEu5kScn704ZEwLKGXQzBfqaA@mail.gmail.com
Link: https://lore.kernel.org/r/20210416205856.3234481-2-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Clean up list_sort prototypes (Sami Tolvanen)
- Introduce CONFIG_CFI_CLANG for arm64 (Sami Tolvanen)
-----BEGIN PGP SIGNATURE-----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=wU6U
-----END PGP SIGNATURE-----
Merge tag 'cfi-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull CFI on arm64 support from Kees Cook:
"This builds on last cycle's LTO work, and allows the arm64 kernels to
be built with Clang's Control Flow Integrity feature. This feature has
happily lived in Android kernels for almost 3 years[1], so I'm excited
to have it ready for upstream.
The wide diffstat is mainly due to the treewide fixing of mismatched
list_sort prototypes. Other things in core kernel are to address
various CFI corner cases. The largest code portion is the CFI runtime
implementation itself (which will be shared by all architectures
implementing support for CFI). The arm64 pieces are Acked by arm64
maintainers rather than coming through the arm64 tree since carrying
this tree over there was going to be awkward.
CFI support for x86 is still under development, but is pretty close.
There are a handful of corner cases on x86 that need some improvements
to Clang and objtool, but otherwise works well.
Summary:
- Clean up list_sort prototypes (Sami Tolvanen)
- Introduce CONFIG_CFI_CLANG for arm64 (Sami Tolvanen)"
* tag 'cfi-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
arm64: allow CONFIG_CFI_CLANG to be selected
KVM: arm64: Disable CFI for nVHE
arm64: ftrace: use function_nocfi for ftrace_call
arm64: add __nocfi to __apply_alternatives
arm64: add __nocfi to functions that jump to a physical address
arm64: use function_nocfi with __pa_symbol
arm64: implement function_nocfi
psci: use function_nocfi for cpu_resume
lkdtm: use function_nocfi
treewide: Change list_sort to use const pointers
bpf: disable CFI in dispatcher functions
kallsyms: strip ThinLTO hashes from static functions
kthread: use WARN_ON_FUNCTION_MISMATCH
workqueue: use WARN_ON_FUNCTION_MISMATCH
module: ensure __cfi_check alignment
mm: add generic function_nocfi macro
cfi: add __cficanonical
add support for Clang CFI
- Add idle states table for IceLake-D to the intel_idle driver and
update IceLake-X C6 data in it (Artem Bityutskiy).
- Fix the C7 idle state on Tegra114 in the tegra cpuidle driver and
drop the unused do_idle() firmware call from it (Dmitry Osipenko).
- Fix cpuidle-qcom-spm Kconfig entry (He Ying).
- Fix handling of possible negative tick_nohz_get_next_hrtimer()
return values of in cpuidle governors (Rafael Wysocki).
- Add support for frequency-invariance to the ACPI CPPC cpufreq
driver and update the frequency-invariance engine (FIE) to use it
as needed (Viresh Kumar).
- Simplify the default delay_us setting in the ACPI CPPC cpufreq
driver (Tom Saeger).
- Clean up frequency-related computations in the intel_pstate
cpufreq driver (Rafael Wysocki).
- Fix TBG parent setting for load levels in the armada-37xx
cpufreq driver and drop the CPU PM clock .set_parent method for
armada-37xx (Marek Behún).
- Fix multiple issues in the armada-37xx cpufreq driver (Pali Rohár).
- Fix handling of dev_pm_opp_of_cpumask_add_table() return values
in cpufreq-dt to take the -EPROBE_DEFER one into acconut as
appropriate (Quanyang Wang).
- Fix format string in ia64-acpi-cpufreq (Sergei Trofimovich).
- Drop the unused for_each_policy() macro from cpufreq (Shaokun
Zhang).
- Simplify computations in the schedutil cpufreq governor to avoid
unnecessary overhead (Yue Hu).
- Fix typos in the s5pv210 cpufreq driver (Bhaskar Chowdhury).
- Fix cpufreq documentation links in Kconfig (Alexander Monakov).
- Fix PCI device power state handling in pci_enable_device_flags()
to avoid issuse in some cases when the device depends on an ACPI
power resource (Rafael Wysocki).
- Add missing documentation of pm_runtime_resume_and_get() (Alan
Stern).
- Add missing static inline stub for pm_runtime_has_no_callbacks()
to pm_runtime.h and drop the unused try_to_freeze_nowarn()
definition (YueHaibing).
- Drop duplicate struct device declaration from pm.h and fix a
structure type declaration in intel_rapl.h (Wan Jiabing).
- Use dev_set_name() instead of an open-coded equivalent of it in
the wakeup sources code and drop a redundant local variable
initialization from it (Andy Shevchenko, Colin Ian King).
- Use crc32 instead of md5 for e820 memory map integrity check
during resume from hibernation on x86 (Chris von Recklinghausen).
- Fix typos in comments in the system-wide and hibernation support
code (Lu Jialin).
- Modify the generic power domains (genpd) code to avoid resuming
devices in the "prepare" phase of system-wide suspend and
hibernation (Ulf Hansson).
- Add Hygon Fam18h RAPL support to the intel_rapl power capping
driver (Pu Wen).
- Add MAINTAINERS entry for the dynamic thermal power management
(DTPM) code (Daniel Lezcano).
- Add devm variants of operating performance points (OPP) API
functions and switch over some users of the OPP framework to
the new resource-managed API (Yangtao Li and Dmitry Osipenko).
- Update devfreq core:
* Register devfreq devices as cooling devices on demand (Daniel
Lezcano).
* Add missing unlock opeation in devfreq_add_device() (Lukasz
Luba).
* Use the next frequency as resume_freq instead of the previous
frequency when using the opp-suspend property (Dong Aisheng).
* Check get_dev_status in devfreq_update_stats() (Dong Aisheng).
* Fix set_freq path for the userspace governor in Kconfig (Dong
Aisheng).
* Remove invalid description of get_target_freq() (Dong Aisheng).
- Update devfreq drivers:
* imx8m-ddrc: Remove imx8m_ddrc_get_dev_status() and unneeded
of_match_ptr() (Dong Aisheng, Fabio Estevam).
* rk3399_dmc: dt-bindings: Add rockchip,pmu phandle and drop
references to undefined symbols (Enric Balletbo i Serra, Gaël
PORTAY).
* rk3399_dmc: Use dev_err_probe() to simplify the code (Krzysztof
Kozlowski).
* imx-bus: Remove unneeded of_match_ptr() (Fabio Estevam).
- Fix kernel-doc warnings in three places (Pierre-Louis Bossart).
- Fix typo in the pm-graph utility code (Ricardo Ribalda).
-----BEGIN PGP SIGNATURE-----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=t+SG
-----END PGP SIGNATURE-----
Merge tag 'pm-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These add some new hardware support (for example, IceLake-D idle
states in intel_idle), fix some issues (for example, the handling of
negative "sleep length" values in cpuidle governors), add new
functionality to the existing drivers (for example, scale-invariance
support in the ACPI CPPC cpufreq driver) and clean up code all over.
Specifics:
- Add idle states table for IceLake-D to the intel_idle driver and
update IceLake-X C6 data in it (Artem Bityutskiy).
- Fix the C7 idle state on Tegra114 in the tegra cpuidle driver and
drop the unused do_idle() firmware call from it (Dmitry Osipenko).
- Fix cpuidle-qcom-spm Kconfig entry (He Ying).
- Fix handling of possible negative tick_nohz_get_next_hrtimer()
return values of in cpuidle governors (Rafael Wysocki).
- Add support for frequency-invariance to the ACPI CPPC cpufreq
driver and update the frequency-invariance engine (FIE) to use it
as needed (Viresh Kumar).
- Simplify the default delay_us setting in the ACPI CPPC cpufreq
driver (Tom Saeger).
- Clean up frequency-related computations in the intel_pstate cpufreq
driver (Rafael Wysocki).
- Fix TBG parent setting for load levels in the armada-37xx cpufreq
driver and drop the CPU PM clock .set_parent method for armada-37xx
(Marek Behún).
- Fix multiple issues in the armada-37xx cpufreq driver (Pali Rohár).
- Fix handling of dev_pm_opp_of_cpumask_add_table() return values in
cpufreq-dt to take the -EPROBE_DEFER one into acconut as
appropriate (Quanyang Wang).
- Fix format string in ia64-acpi-cpufreq (Sergei Trofimovich).
- Drop the unused for_each_policy() macro from cpufreq (Shaokun
Zhang).
- Simplify computations in the schedutil cpufreq governor to avoid
unnecessary overhead (Yue Hu).
- Fix typos in the s5pv210 cpufreq driver (Bhaskar Chowdhury).
- Fix cpufreq documentation links in Kconfig (Alexander Monakov).
- Fix PCI device power state handling in pci_enable_device_flags() to
avoid issuse in some cases when the device depends on an ACPI power
resource (Rafael Wysocki).
- Add missing documentation of pm_runtime_resume_and_get() (Alan
Stern).
- Add missing static inline stub for pm_runtime_has_no_callbacks() to
pm_runtime.h and drop the unused try_to_freeze_nowarn() definition
(YueHaibing).
- Drop duplicate struct device declaration from pm.h and fix a
structure type declaration in intel_rapl.h (Wan Jiabing).
- Use dev_set_name() instead of an open-coded equivalent of it in the
wakeup sources code and drop a redundant local variable
initialization from it (Andy Shevchenko, Colin Ian King).
- Use crc32 instead of md5 for e820 memory map integrity check during
resume from hibernation on x86 (Chris von Recklinghausen).
- Fix typos in comments in the system-wide and hibernation support
code (Lu Jialin).
- Modify the generic power domains (genpd) code to avoid resuming
devices in the "prepare" phase of system-wide suspend and
hibernation (Ulf Hansson).
- Add Hygon Fam18h RAPL support to the intel_rapl power capping
driver (Pu Wen).
- Add MAINTAINERS entry for the dynamic thermal power management
(DTPM) code (Daniel Lezcano).
- Add devm variants of operating performance points (OPP) API
functions and switch over some users of the OPP framework to the
new resource-managed API (Yangtao Li and Dmitry Osipenko).
- Update devfreq core:
* Register devfreq devices as cooling devices on demand (Daniel
Lezcano).
* Add missing unlock opeation in devfreq_add_device() (Lukasz
Luba).
* Use the next frequency as resume_freq instead of the previous
frequency when using the opp-suspend property (Dong Aisheng).
* Check get_dev_status in devfreq_update_stats() (Dong Aisheng).
* Fix set_freq path for the userspace governor in Kconfig (Dong
Aisheng).
* Remove invalid description of get_target_freq() (Dong Aisheng).
- Update devfreq drivers:
* imx8m-ddrc: Remove imx8m_ddrc_get_dev_status() and unneeded
of_match_ptr() (Dong Aisheng, Fabio Estevam).
* rk3399_dmc: dt-bindings: Add rockchip,pmu phandle and drop
references to undefined symbols (Enric Balletbo i Serra, Gaël
PORTAY).
* rk3399_dmc: Use dev_err_probe() to simplify the code (Krzysztof
Kozlowski).
* imx-bus: Remove unneeded of_match_ptr() (Fabio Estevam).
- Fix kernel-doc warnings in three places (Pierre-Louis Bossart).
- Fix typo in the pm-graph utility code (Ricardo Ribalda)"
* tag 'pm-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (74 commits)
PM: wakeup: remove redundant assignment to variable retval
PM: hibernate: x86: Use crc32 instead of md5 for hibernation e820 integrity check
cpufreq: Kconfig: fix documentation links
PM: wakeup: use dev_set_name() directly
PM: runtime: Add documentation for pm_runtime_resume_and_get()
cpufreq: intel_pstate: Simplify intel_pstate_update_perf_limits()
cpufreq: armada-37xx: Fix module unloading
cpufreq: armada-37xx: Remove cur_frequency variable
cpufreq: armada-37xx: Fix determining base CPU frequency
cpufreq: armada-37xx: Fix driver cleanup when registration failed
clk: mvebu: armada-37xx-periph: Fix workaround for switching from L1 to L0
clk: mvebu: armada-37xx-periph: Fix switching CPU freq from 250 Mhz to 1 GHz
cpufreq: armada-37xx: Fix the AVS value for load L1
clk: mvebu: armada-37xx-periph: remove .set_parent method for CPU PM clock
cpufreq: armada-37xx: Fix setting TBG parent for load levels
cpuidle: Fix ARM_QCOM_SPM_CPUIDLE configuration
cpuidle: tegra: Remove do_idle firmware call
cpuidle: tegra: Fix C7 idling state on Tegra114
PM: sleep: fix typos in comments
cpufreq: Remove unused for_each_policy macro
...
Almost all SoC code changes this time are for the TI OMAP
platform, which continues its decade-long quest to move from
describing a complex SoC in code to device tree.
Aside from this, the Uniphier platform has a new maintainer
and some platforms have minor bugfixes and cleanups that were
not urgent enough for v5.12.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=YFEX
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"Almost all SoC code changes this time are for the TI OMAP platform,
which continues its decade-long quest to move from describing a
complex SoC in code to device tree.
Aside from this, the Uniphier platform has a new maintainer and some
platforms have minor bugfixes and cleanups that were not urgent enough
for v5.12"
* tag 'arm-soc-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (96 commits)
MAINTAINERS: Update ARM/UniPhier SoCs maintainers and status
mailmap: Update email address for Nicolas Saenz
MAINTAINERS: Update BCM2711/BCM2335 maintainer's mail
ARM: exynos: correct kernel doc in platsmp
ARM: hisi: use the correct HiSilicon copyright
ARM: ux500: make ux500_cpu_die static
ARM: s3c: Use pwm_get() in favour of pwm_request() in RX1950
ARM: OMAP1: fix incorrect kernel-doc comment syntax in file
ARM: OMAP2+: fix incorrect kernel-doc comment syntax in file
ARM: OMAP2+: Use DEFINE_SPINLOCK() for spinlock
ARM: at91: pm: Move prototypes to mutually included header
ARM: OMAP2+: use true and false for bool variable
ARM: OMAP2+: add missing call to of_node_put()
ARM: OMAP2+: Replace DEFINE_SIMPLE_ATTRIBUTE with DEFINE_DEBUGFS_ATTRIBUTE
ARM: imx: Kconfig: Fix typo in help
ARM: mach-imx: Fix a spelling in the file pm-imx5.c
bus: ti-sysc: Warn about old dtb for dra7 and omap4/5
ARM: OMAP2+: Stop building legacy code for dra7 and omap4/5
ARM: OMAP2+: Drop legacy platform data for omap5 hwmod
ARM: OMAP2+: Drop legacy platform data for omap5 l3
...
Core changes:
- Provide IRQF_NO_AUTOEN as a flag for request*_irq() so drivers can be
cleaned up which either use a seperate mechanism to prevent auto-enable
at request time or have a racy mechanism which disables the interrupt
right after request.
- Get rid of the last usage of irq_create_identity_mapping() and remove
the interface.
- An overhaul of tasklet_disable(). Most usage sites of tasklet_disable()
are in task context and usually in cleanup, teardown code pathes.
tasklet_disable() spinwaits for a tasklet which is currently executed.
That's not only a problem for PREEMPT_RT where this can lead to a live
lock when the disabling task preempts the softirq thread. It's also
problematic in context of virtualization when the vCPU which runs the
tasklet is scheduled out and the disabling code has to spin wait until
it's scheduled back in. Though there are a few code pathes which invoke
tasklet_disable() from non-sleepable context. For these a new disable
variant which still spinwaits is provided which allows to switch
tasklet_disable() to a sleep wait mechanism. For the atomic use cases
this does not solve the live lock issue on PREEMPT_RT. That is mitigated
by blocking on the RT specific softirq lock.
- The PREEMPT_RT specific implementation of softirq processing and
local_bh_disable/enable().
On RT enabled kernels soft interrupt processing happens always in task
context and all interrupt handlers, which are not explicitly marked to
be invoked in hard interrupt context are forced into task context as
well. This allows to protect against softirq processing with a per
CPU lock, which in turn allows to make BH disabled regions preemptible.
Most of the softirq handling code is still shared. The RT/non-RT
specific differences are addressed with a set of inline functions which
provide the context specific functionality. The local_bh_disable() /
local_bh_enable() mechanism are obviously seperate.
- The usual set of small improvements and cleanups
Driver changes:
- New drivers for Nuvoton WPCM450 and DT 79rc3243x interrupt controllers
- Extended functionality for MStar, STM32 and SC7280 irq chips
- Enhanced robustness for ARM GICv3/4.1 drivers
- The usual set of cleanups and improvements all over the place
-----BEGIN PGP SIGNATURE-----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=id4G
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2021-04-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"The usual updates from the irq departement:
Core changes:
- Provide IRQF_NO_AUTOEN as a flag for request*_irq() so drivers can
be cleaned up which either use a seperate mechanism to prevent
auto-enable at request time or have a racy mechanism which disables
the interrupt right after request.
- Get rid of the last usage of irq_create_identity_mapping() and
remove the interface.
- An overhaul of tasklet_disable().
Most usage sites of tasklet_disable() are in task context and
usually in cleanup, teardown code pathes. tasklet_disable()
spinwaits for a tasklet which is currently executed. That's not
only a problem for PREEMPT_RT where this can lead to a live lock
when the disabling task preempts the softirq thread. It's also
problematic in context of virtualization when the vCPU which runs
the tasklet is scheduled out and the disabling code has to spin
wait until it's scheduled back in.
There are a few code pathes which invoke tasklet_disable() from
non-sleepable context. For these a new disable variant which still
spinwaits is provided which allows to switch tasklet_disable() to a
sleep wait mechanism. For the atomic use cases this does not solve
the live lock issue on PREEMPT_RT. That is mitigated by blocking on
the RT specific softirq lock.
- The PREEMPT_RT specific implementation of softirq processing and
local_bh_disable/enable().
On RT enabled kernels soft interrupt processing happens always in
task context and all interrupt handlers, which are not explicitly
marked to be invoked in hard interrupt context are forced into task
context as well. This allows to protect against softirq processing
with a per CPU lock, which in turn allows to make BH disabled
regions preemptible.
Most of the softirq handling code is still shared. The RT/non-RT
specific differences are addressed with a set of inline functions
which provide the context specific functionality. The
local_bh_disable() / local_bh_enable() mechanism are obviously
seperate.
- The usual set of small improvements and cleanups
Driver changes:
- New drivers for Nuvoton WPCM450 and DT 79rc3243x interrupt
controllers
- Extended functionality for MStar, STM32 and SC7280 irq chips
- Enhanced robustness for ARM GICv3/4.1 drivers
- The usual set of cleanups and improvements all over the place"
* tag 'irq-core-2021-04-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (53 commits)
irqchip/xilinx: Expose Kconfig option for Zynq/ZynqMP
irqchip/gic-v3: Do not enable irqs when handling spurious interrups
dt-bindings: interrupt-controller: Add IDT 79RC3243x Interrupt Controller
irqchip: Add support for IDT 79rc3243x interrupt controller
irqdomain: Drop references to recusive irqdomain setup
irqdomain: Get rid of irq_create_strict_mappings()
irqchip/jcore-aic: Kill use of irq_create_strict_mappings()
ARM: PXA: Kill use of irq_create_strict_mappings()
irqchip/gic-v4.1: Disable vSGI upon (GIC CPUIF < v4.1) detection
irqchip/tb10x: Use 'fallthrough' to eliminate a warning
genirq: Reduce irqdebug cacheline bouncing
kernel: Initialize cpumask before parsing
irqchip/wpcm450: Drop COMPILE_TEST
irqchip/irq-mst: Support polarity configuration
irqchip: Add driver for WPCM450 interrupt controller
dt-bindings: interrupt-controller: Add nuvoton, wpcm450-aic
dt-bindings: qcom,pdc: Add compatible for sc7280
irqchip/stm32: Add usart instances exti direct event support
irqchip/gic-v3: Fix OF_BAD_ADDR error handling
irqchip/sifive-plic: Mark two global variables __ro_after_init
...
There is not a consistent pattern for checking Hyper-V hypercall status.
Existing code uses a number of variants. The variants work, but a consistent
pattern would improve the readability of the code, and be more conformant
to what the Hyper-V TLFS says about hypercall status.
Implemented new helper functions hv_result(), hv_result_success(), and
hv_repcomp(). Changed the places where hv_do_hypercall() and related variants
are used to use the helper functions.
Signed-off-by: Joseph Salisbury <joseph.salisbury@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/1618620183-9967-2-git-send-email-joseph.salisbury@linux.microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
The few quirks that deal with NO_MSI tend to be copy-paste heavy.
Refactor them so that the hierarchy of conditions is slightly
cleaner.
Link: https://lore.kernel.org/r/20210330151145.997953-15-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
We have now three ways of ending up with NO_MSI being set.
Document them.
Link: https://lore.kernel.org/r/20210330151145.997953-14-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Some Mediatek host bridges cannot handle MSIs, which is sad.
This also results in an ugly warning at device probe time,
as the core PCI code wasn't told that MSIs were not available.
Advertise this fact to the rest of the core PCI code by
using the 'msi_domain' attribute, which still opens the possibility
for another block to provide the MSI functionnality.
[maz: commit message, switched over to msi_domain attribute]
Link: https://lore.kernel.org/r/20210330151145.997953-13-maz@kernel.org
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The generic PCI host driver relies on MSI domains for MSIs to
be provided to its end-points. Make this dependency explicit.
This cures the warnings occuring on arm/arm64 VMs when booted
with PCI virtio devices and no MSI controller (no GICv3 ITS,
for example).
It is likely that other drivers will need to express the same
dependency.
Link: https://lore.kernel.org/r/20210330151145.997953-12-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
There is a whole class of host bridges that cannot know whether
MSIs will be provided or not, as they rely on other blocks
to provide the MSI functionnality, using MSI domains. This is
the case for example on systems that use the ARM GIC architecture.
Introduce a new attribute ('msi_domain') indicating that implicit
dependency, and use this property to set the NO_MSI flag when
no MSI domain is found at probe time.
Link: https://lore.kernel.org/r/20210330151145.997953-11-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
As there is no driver using msi_controller, we can now safely
remove its use from the PCI probe code.
Link: https://lore.kernel.org/r/20210330151145.997953-8-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The Hyper-V PCI driver still makes use of a msi_controller structure,
but it looks more like a distant leftover than anything actually
useful, since it is initialised to 0 and never used for anything.
Just remove it.
Link: https://lore.kernel.org/r/20210330151145.997953-7-maz@kernel.org
Tested-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
In anticipation of the removal of the msi_controller structure, convert
the ancient xilinx host controller driver to MSI domains.
We end-up with the usual two domain structure, the top one being a
generic PCI/MSI domain, the bottom one being xilinx-specific and handling
the actual HW interrupt allocation.
This allows us to fix some of the most appaling MSI programming, where
the message programmed in the device is the virtual IRQ number instead
of the allocated vector number. The allocator is also made safe with
a mutex. This should allow support for MultiMSI, but I decided not to
even try, since I cannot test it.
Link: https://lore.kernel.org/r/20210330151145.997953-6-maz@kernel.org
Tested-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
A long cargo-culted behaviour of PCI drivers is to allocate memory
to obtain an address that is fed to the controller as the MSI
capture address (i.e. the MSI doorbell).
But there is no actual requirement for this address to be RAM.
All it needs to be is a suitable aligned address that will
*not* be DMA'd to.
Use the physical address of the 'port' data structure as the MSI
capture address, aligned on a 4K boundary.
Link: https://lore.kernel.org/r/20210330151145.997953-5-maz@kernel.org
Tested-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
In anticipation of the removal of the msi_controller structure, convert
the Rcar host controller driver to MSI domains.
We end-up with the usual two domain structure, the top one being a
generic PCI/MSI domain, the bottom one being Rcar-specific and handling
the actual HW interrupt allocation.
Link: https://lore.kernel.org/r/20210330151145.997953-4-maz@kernel.org
Tested-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
[lorenzo.pieralisi@arm.com: merged fix https://lore.kernel.org/linux-pci/87y2e2p9wk.wl-maz@kernel.org]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
A long cargo-culted behaviour of PCI drivers is to allocate memory
to obtain an address that is fed to the controller as the MSI
capture address (i.e. the MSI doorbell).
But there is no actual requirement for this address to be RAM.
All it needs to be is a suitable aligned address that will
*not* be DMA'd to.
Since the rcar platform already has a requirement that this
address should be in the first 4GB of the physical address space,
use the controller's own base address as the capture address.
Link: https://lore.kernel.org/r/20210330151145.997953-3-maz@kernel.org
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
In anticipation of the removal of the msi_controller structure, convert
the Tegra host controller driver to MSI domains.
We end-up with the usual two domain structure, the top one being a
generic PCI/MSI domain, the bottom one being Tegra-specific and handling
the actual HW interrupt allocation.
While at it, convert the normal interrupt handler to a chained handler,
handle the controller's MSI IRQ edge triggered, support multiple MSIs
per device and use the AFI_MSI_EN_VEC* registers to provide MSI masking.
[treding@nvidia.com: fix, clean up and address TODOs from Marc's draft]
Link: https://lore.kernel.org/r/20210330151145.997953-2-maz@kernel.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
This interface will be used by PCI host drivers for PIO translation,
export it to support compiling those drivers as kernel modules.
Link: https://lore.kernel.org/r/20210420061723.989-3-jianjun.wang@mediatek.com
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The PCIe controller in Tegra194 SoC is not ECAM-compliant. With the
current hardware design, ECAM can be enabled only for one controller (the
C5 controller) with bus numbers starting from 160 instead of 0. A different
approach is taken to avoid this abnormal way of enabling ECAM for just one
controller but to enable configuration space access for all the other
controllers. In this approach, ops are added through MCFG quirk mechanism
which access the configuration spaces by dynamically programming iATU
(internal AddressTranslation Unit) to generate respective configuration
accesses just like the way it is done in DesignWare core sub-system.
This issue is specific to Tegra194 and it would be fixed in the future
generations of Tegra SoCs.
Link: https://lore.kernel.org/r/20210416134537.19474-1-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
There is a error message within devm_ioremap_resource()
already, so remove the dev_err() call to avoid redundant
error message.
Link: https://lore.kernel.org/r/20210409075748.226141-1-clare.chenhui@huawei.com
Signed-off-by: Chen Hui <clare.chenhui@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Link: https://lore.kernel.org/r/20210331085938.3115-1-linqiheng@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Qiheng Lin <linqiheng@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add the missing destroy_workqueue() before return from
pci_epf_test_init() in the error handling case and add
destroy_workqueue() in pci_epf_test_exit().
Link: https://lore.kernel.org/r/20210331084012.2091010-1-yangyingliang@huawei.com
Fixes: 349e7a85b2 ("PCI: endpoint: functions: Add an EP function to test PCI")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The pointer dev is being initialized with a value that is
never read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Link: https://lore.kernel.org/r/20210326190909.622369-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Currently zpci_configure_device() can be called on a zPCI function in
two completely different states. Either the underlying zPCI function has
already been configured by the platform and we are only doing the
scanning to get it usable by Linux drivers. Or the underlying function
is in Standby and we first do an SCLP to get it configured. This makes
zpci_configure_device() harder to reason about. Since calling
zpci_configure_device() on a function in Standby only happens in
enable_slot() simply pull out the SCLP call and setting of zdev->state
and thus call zpci_configure_device() under the same circumstances as
in the event handling code.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Saeed Mahameed says:
====================
mlx5-next 2021-04-09
This pr contains changes from mlx5-next branch,
already reviewed on netdev and rdma mailing lists, links below.
1) From Leon, Dynamically assign MSI-X vectors count
Already Acked by Bjorn Helgaas.
https://patchwork.kernel.org/project/netdevbpf/cover/20210314124256.70253-1-leon@kernel.org/
2) Cleanup series:
https://patchwork.kernel.org/project/netdevbpf/cover/20210311070915.321814-1-saeed@kernel.org/
From Mark, E-Switch cleanups and refactoring, and the addition
of single FDB mode needed HW bits.
From Mikhael, Remove unused struct field
From Saeed, Cleanup W=1 prototype warning
From Zheng, Esw related cleanup
From Tariq, User order-0 page allocation for EQs
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5: Implement sriov_get_vf_total_msix/count() callbacks
net/mlx5: Dynamically assign MSI-X vectors count
net/mlx5: Add dynamic MSI-X capabilities bits
PCI/IOV: Add sysfs MSI-X vector assignment interface
net/mlx5: Use order-0 allocations for EQs
net/mlx5: Add IFC bits needed for single FDB mode
net/mlx5: E-Switch, Refactor send to vport to be more generic
RDMA/mlx5: Use representor E-Switch when getting netdev and metadata
net/mlx5: E-Switch, Add eswitch pointer to each representor
net/mlx5: E-Switch, Add match on vhca id to default send rules
net/mlx5: Remove unused mlx5_core_health member recover_work
net/mlx5: simplify the return expression of mlx5_esw_offloads_pair()
net/mlx5: Cleanup prototype warning
====================
Link: https://lore.kernel.org/r/20210409200704.10886-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Like the Intel DC P3700 NVMe, the Intel P4510 NVMe exhibits a timeout
failure when the driver tries to interact with the device too soon after an
FLR.
Add a device-specific reset method that delays 250ms after doing an FLR.
Link: https://lore.kernel.org/r/20210408190521.16897-1-raphael.norwitz@nutanix.com
Signed-off-by: Alay Shah <alay.shah@nutanix.com>
Signed-off-by: Suresh Gumpula <suresh.gumpula@nutanix.com>
Signed-off-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
list_sort() internally casts the comparison function passed to it
to a different type with constant struct list_head pointers, and
uses this pointer to call the functions, which trips indirect call
Control-Flow Integrity (CFI) checking.
Instead of removing the consts, this change defines the
list_cmp_func_t type and changes the comparison function types of
all list_sort() callers to use const pointers, thus avoiding type
mismatches.
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210408182843.1754385-10-samitolvanen@google.com
pm_runtime_get_sync() will increase the runtime PM counter
even it returns an error. Thus a pairing decrement is needed
to prevent refcount leak. Fix this by replacing this API with
pm_runtime_resume_and_get(), which will not change the runtime
PM counter on error.
Link: https://lore.kernel.org/r/20210408072700.15791-1-dinghao.liu@zju.edu.cn
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
In enable_slot(), if pci_get_slot() returns NULL, we clear the SLOT_ENABLED
flag. When pci_get_slot() finds a device, it increments the device's
reference count. In this case, we did not call pci_dev_put() to decrement
the reference count, so the memory of the device (struct pci_dev type) will
eventually leak.
Call pci_dev_put() to decrement its reference count when pci_get_slot()
returns a PCI device.
Link: https://lore.kernel.org/r/b411af88-5049-a1c6-83ac-d104a1f429be@huawei.com
Signed-off-by: Feilong Lin <linfeilong@huawei.com>
Signed-off-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A typical cloud provider SR-IOV use case is to create many VFs for use by
guest VMs. The VFs may not be assigned to a VM until a customer requests a
VM of a certain size, e.g., number of CPUs. A VF may need MSI-X vectors
proportional to the number of CPUs in the VM, but there is no standard way
to change the number of MSI-X vectors supported by a VF.
Some Mellanox ConnectX devices support dynamic assignment of MSI-X vectors
to SR-IOV VFs. This can be done by the PF driver after VFs are enabled,
and it can be done without affecting VFs that are already in use. The
hardware supports a limited pool of MSI-X vectors that can be assigned to
the PF or to individual VFs. This is device-specific behavior that
requires support in the PF driver.
Add a read-only "sriov_vf_total_msix" sysfs file for the PF and a writable
"sriov_vf_msix_count" file for each VF. Management software may use these
to learn how many MSI-X vectors are available and to dynamically assign
them to VFs before the VFs are passed through to a VM.
If the PF driver implements the ->sriov_get_vf_total_msix() callback,
"sriov_vf_total_msix" contains the total number of MSI-X vectors available
for distribution among VFs.
If no driver is bound to the VF, writing "N" to "sriov_vf_msix_count" uses
the PF driver ->sriov_set_msix_vec_count() callback to assign "N" MSI-X
vectors to the VF. When a VF driver subsequently reads the MSI-X Message
Control register, it will see the new Table Size "N".
Link: https://lore.kernel.org/linux-pci/20210314124256.70253-2-leon@kernel.org
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
If PCI_D3cold is passed to acpi_pci_set_power_state() as the second
argument and there is no ACPI D3cold support for the given device, the
debug message will state that the device power state has been changed to
D3cold, while in fact it will be D3hot, because acpi_device_set_power()
falls back to D3hot automatically if D3cold is not supported without
returning an error.
To address this issue, modify the debug message to print the current power
state of the target PCI device's ACPI companion instead of printing the
target power state, which may not reflect the real final power state of the
device.
Link: https://lore.kernel.org/r/4319486.LvFx2qVVIh@kreacher
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
For Mellanox Tavor devices, we previously set dev->broken_parity_status,
which does not change the device's behavior; it merely prevents the EDAC
PCI error reporting from warning about Master Data Parity Error, Signaled
System Error, or Detected Parity Error for this device.
Instead, disable Parity Error Response so the device doesn't report
parity errors in the first place.
[bhelgaas: split out pci_disable_parity(), commit log, keep quirk static]
Link: https://lore.kernel.org/r/20210330174318.1289680-3-helgaas@kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Add pci_disable_parity() to disable reporting of parity errors for a
device by clearing PCI_COMMAND_PARITY.
The device will still set PCI_STATUS_DETECTED_PARITY when it detects
a parity error or receives a Poisoned TLP, but it will not set
PCI_STATUS_PARITY, which means it will not assert PERR#
(conventional PCI) or report Poisoned TLPs (PCIe).
Based-on: https://lore.kernel.org/linux-arm-kernel/d375987c-ea4f-dd98-4ef8-99b2fbfe7c33@gmail.com/
Based-on-patch-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/20210330174318.1289680-2-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In commit e2dcd20b16 a change was made to use
devm_platform_ioremap_resource_byname() to simplify code and remove
the res variable; this was wrong since the res variable is still needed
and as an outcome the port->cfg_addr gets an erroneous address.
Revert the change going back to original behaviour.
Link: https://lore.kernel.org/r/20210328144118.305074-1-zhengdejin5@gmail.com
Fixes: e2dcd20b16 ("PCI: controller: Convert to devm_platform_ioremap_resource_byname()")
Reported-by: dann.frazier@canonical.com
Tested-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # v5.9+
Since 104daa71b3 ("PCI: Determine actual VPD size on first access")
attribute size is set to 0 (unlimited).
Remove the dead code that checks for "bin_attr->size > 0".
Link: https://lore.kernel.org/r/267eae86-f8a6-6792-a7f8-2c4fd51beedc@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
quirk_brcm_570x_limit_vpd() was added in 2008 [0] when we didn't have the
logic to determine VPD size based on checking for the VPD end tag. Now
that we do have this logic [1] and don't read beyond the end tag, this
quirk can be removed.
[0] 99cb233d60 ("PCI: Limit VPD read/write lengths for Broadcom 5706, 5708, 5709 rev.")
[1] 104daa71b3 ("PCI: Determine actual VPD size on first access")
Link: https://lore.kernel.org/r/daa6acdf-5027-62c8-e3fb-125411b018f5@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
"PCI_FUNC(port->slot << 3)" is always 0, so previously
mtk_pcie_startup_port() only configured FC credits and FTs for function
0.
Compute "func" correctly so we also configure functions other than
0. This affects MT2701 and MT7623.
Link: https://lore.kernel.org/r/c529dbfc066f4bda9b87edbdbf771f207e69b84e.1604510053.git.ryder.lee@mediatek.com
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
get_features ops of pci_epc_ops may return NULL, causing NULL pointer
dereference in pci_epf_test_alloc_space function. Let us add a check for
pci_epc_feature pointer in pci_epf_test_bind before we access it to avoid
any such NULL pointer dereference and return -ENOTSUPP in case
pci_epc_feature is not found.
When the patch is not applied and EPC features is not implemented in the
platform driver, we see the following dump due to kernel NULL pointer
dereference.
Call trace:
pci_epf_test_bind+0xf4/0x388
pci_epf_bind+0x3c/0x80
pci_epc_epf_link+0xa8/0xcc
configfs_symlink+0x1a4/0x48c
vfs_symlink+0x104/0x184
do_symlinkat+0x80/0xd4
__arm64_sys_symlinkat+0x1c/0x24
el0_svc_common.constprop.3+0xb8/0x170
el0_svc_handler+0x70/0x88
el0_svc+0x8/0x640
Code: d2800581 b9403ab9 f9404ebb 8b394f60 (f9400400)
---[ end trace a438e3c5a24f9df0 ]---
Link: https://lore.kernel.org/r/20210324101609.79278-1-shradha.t@samsung.com
Fixes: 2c04c5b8ee ("PCI: pci-epf-test: Use pci_epc_get_features() to get EPC features")
Signed-off-by: Sriram Dash <dash.sriram@gmail.com>
Signed-off-by: Shradha Todi <shradha.t@samsung.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
It should not be necessary to update the current_state field of
struct pci_dev in pci_enable_device_flags() before calling
do_pci_enable_device() for the device, because none of the
code between that point and the pci_set_power_state() call in
do_pci_enable_device() invoked later depends on it.
Moreover, doing that is actively harmful in some cases. For example,
if the given PCI device depends on an ACPI power resource whose _STA
method initially returns 0 ("off"), but the config space of the PCI
device is accessible and the power state retrieved from the
PCI_PM_CTRL register is D0, the current_state field in the struct
pci_dev representing that device will get out of sync with the
power.state of its ACPI companion object and that will lead to
power management issues going forward.
To avoid such issues it is better to leave the current_state value
as is until it is changed to PCI_D0 by do_pci_enable_device() as
appropriate. However, the power state of the device is not changed
to PCI_D0 if it is already enabled when pci_enable_device_flags()
gets called for it, so update its current_state in that case, but
use pci_update_current_state() covering platform PM too for that.
Link: https://lore.kernel.org/lkml/20210314000439.3138941-1-luzmaximilian@gmail.com/
Reported-by: Maximilian Luz <luzmaximilian@gmail.com>
Tested-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In pci_scan_device(), if pci_setup_device() fails for any reason, the code
will not release device's of_node by calling pci_release_of_node(). Fix
that by calling the release function.
Fixes: 98d9f30c82 ("pci/of: Match PCI devices to OF nodes dynamically")
Link: https://lore.kernel.org/r/20210124232826.1879-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
- Drop the dependency on PCI, as this is implied by the dependency on
PCI_MSI_IRQ_DOMAIN,
- Drop the dependencies on OF and ARM64, as the driver compiles fine
without OF and/or on other architectures,
- The Freescale Layerscape PCIe Gen4 controller is present only on
Freescale Layerscape SoCs. Hence depend on ARCH_LAYERSCAPE, to
prevent asking the user about this driver when configuring a kernel
without Freescale Layerscape support, unless compile-testing.
Link: https://lore.kernel.org/r/20210208142301.413582-1-geert+renesas@glider.be
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
In config PCIE_TEGRA194_EP the mode incorrectly is referred to as
host mode. Fix it.
Link: https://lore.kernel.org/r/20201231032539.22322-1-wesley.sheng@amd.com
Signed-off-by: Wesley Sheng <wesley.sheng@amd.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
Fix to return negative error code -ENODEV from the unsupported revision
error handling case instead of 0, as done elsewhere in this function.
Link: https://lore.kernel.org/r/20210308135619.19133-1-weiyongjun1@huawei.com
Fixes: 0cdfaceb98 ("PCI: brcmstb: support BCM4908 with external PERST# signal controller")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Both TI's AM65x (K3) and TI's K2 PCIe driver are implemented in
pci-keystone. However Only K2 PCIe driver should use it's own pci_ops
for configuration space accesses. But commit 10a797c6e5
("PCI: dwc: keystone: Use pci_ops for config space accessors") used
custom pci_ops for both AM65x and K2. This breaks configuration space
access for AM65x platform. Fix it here.
Link: https://lore.kernel.org/r/20210317131518.11040-1-kishon@ti.com
Fixes: 10a797c6e5 ("PCI: dwc: keystone: Use pci_ops for config space accessors")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Cc: <stable@vger.kernel.org> # v5.10
There is no need to call the dev_err() function directly to print a
custom message when handling an error from either the platform_get_irq()
or platform_get_irq_byname() functions as both are going to display an
appropriate error message in case of a failure.
This change is as per suggestions from Coccinelle, e.g.,
drivers/pci/controller/pcie-microchip-host.c:1027:2-9: line 1027 is
redundant because platform_get_irq() already prints an error
Related commit caecb05c80 ("PCI: Remove dev_err() when handing an
error from platform_get_irq()").
Link: https://lore.kernel.org/r/20210310131913.2802385-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The sparse tool complains as follows:
drivers/pci/controller/pcie-microchip-host.c:304:18: warning:
symbol 'pcie_event_to_event' was not declared. Should it be static?
drivers/pci/controller/pcie-microchip-host.c:310:18: warning:
symbol 'sec_error_to_event' was not declared. Should it be static?
drivers/pci/controller/pcie-microchip-host.c:317:18: warning:
symbol 'ded_error_to_event' was not declared. Should it be static?
drivers/pci/controller/pcie-microchip-host.c:324:18: warning:
symbol 'local_status_to_event' was not declared. Should it be static?
Those symbols are not used outside of pcie-microchip-host.c, so this
commit marks them static.
Link: https://lore.kernel.org/r/20210308094842.3588847-1-weiyongjun1@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
IRQ domain alloc function should return zero on success. Non-zero value
indicates failure.
Link: https://lore.kernel.org/r/20210303142202.25780-1-pali@kernel.org
Fixes: fc54bae288 ("PCI: iproc: Allow allocation of multiple MSIs")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Marc Zyngier <maz@kernel.org>
VMD will retransmit child device MSI-X using its own MSI-X table and
requester-id. This limits the number of MSI-X available to the whole
child device domain to the number of VMD MSI-X interrupts.
Some VMD devices have a mode where this remapping can be disabled,
allowing child device interrupts to bypass processing with the VMD MSI-X
domain interrupt handler and going straight the child device interrupt
handler, allowing for better performance and scaling. The requester-id
still gets changed to the VMD endpoint's requester-id, and the interrupt
remapping handlers have been updated to properly set IRTE for child
device interrupts to the VMD endpoint's context.
Some VMD platforms have existing production BIOS which rely on MSI-X
remapping and won't explicitly program the MSI-X remapping bit. This
re-enables MSI-X remapping on unload.
Link: https://lore.kernel.org/r/20210210161315.316097-3-jonathan.derrick@intel.com
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
The only usage of them is to assign their address to the 'ops' field in
the pcie_port and the dw_pcie_ep structs, both which are pointers to
const. Make them const to allow the compiler to put them in read-only
memory.
Link: https://lore.kernel.org/r/20210207221604.48910-1-rikard.falkeborn@gmail.com
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
A zPCI event with PEC 0x0301 for an existing zPCI device goes through
the same actions as enable_slot(). Similarly a zPCI event with PEC
0x0303 does the same steps as disable_slot().
We can thus unify both actions as zpci_configure_device() respectively
zpci_deconfigure_device().
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
The current zdev->state mixes the configuration states supported by CLP
with an additional Online state which is used inconsistently to include
enabled zPCI functions which are not yet visible to the common PCI
subsytem. In preparation for a clean separation between architected
configuration states and fine grained function states remove the Online
function state.
Where we previously checked for Online it is more accurate to check if
the function is enabled to avoid an edge case where a disabled device
was still treated as Online. This also simplifies checks whether
a function is configured as this is now directly reflected by its
function state.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Fix a possible stack corruption and subsequent DLPAR failure in the rpadlpar_io
PCI hotplug driver.
Two build fixes for uncommon configurations.
Thanks to Christophe Leroy, Tyrel Datwyler.
-----BEGIN PGP SIGNATURE-----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=SHvi
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.12-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix a possible stack corruption and subsequent DLPAR failure in the
rpadlpar_io PCI hotplug driver
- Two build fixes for uncommon configurations
Thanks to Christophe Leroy and Tyrel Datwyler.
* tag 'powerpc-5.12-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
PCI: rpadlpar: Fix potential drc_name corruption in store functions
powerpc: Force inlining of cpu_has_feature() to avoid build failure
powerpc/vdso32: Add missing _restgpr_31_x to fix build failure
All callers just use it to check if swiotlb is active at all, for which
they can just use is_swiotlb_active. In the longer run drivers need
to stop using is_swiotlb_active as well, but let's do the simple step
first.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The hv_compose_msi_msg() callback in irq_chip::irq_compose_msi_msg is
invoked via irq_chip_compose_msi_msg(), which itself is always invoked from
atomic contexts from the guts of the interrupt core code.
There is no way to change this w/o rewriting the whole driver, so use
tasklet_disable_in_atomic() which allows to make tasklet_disable()
sleepable once the remaining atomic users are addressed.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Wei Liu <wei.liu@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20210309084242.516519290@linutronix.de
Both add_slot_store() and remove_slot_store() try to fix up the
drc_name copied from the store buffer by placing a NUL terminator at
nbyte + 1 or in place of a '\n' if present. However, the static buffer
that we copy the drc_name data into is not zeroed and can contain
anything past the n-th byte.
This is problematic if a '\n' byte appears in that buffer after nbytes
and the string copied into the store buffer was not NUL terminated to
start with as the strchr() search for a '\n' byte will mark this
incorrectly as the end of the drc_name string resulting in a drc_name
string that contains garbage data after the n-th byte.
Additionally it will cause us to overwrite that '\n' byte on the stack
with NUL, potentially corrupting data on the stack.
The following debugging shows an example of the drmgr utility writing
"PHB 4543" to the add_slot sysfs attribute, but add_slot_store()
logging a corrupted string value.
drmgr: drmgr: -c phb -a -s PHB 4543 -d 1
add_slot_store: drc_name = PHB 4543°|<82>!, rc = -19
Fix this by using strscpy() instead of memcpy() to ensure the string
is NUL terminated when copied into the static drc_name buffer.
Further, since the string is now NUL terminated the code only needs to
change '\n' to '\0' when present.
Cc: stable@vger.kernel.org
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
[mpe: Reformat change log and add mention of possible stack corruption]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210315214821.452959-1-tyreld@linux.ibm.com
Add pci_find_vsec_capability() to locate a Vendor-Specific Extended
Capability with the specified VSEC ID.
The Vendor-Specific Extended Capability (VSEC) allows one or more
proprietary capabilities defined by the vendor which aren't standard
or shared between vendors.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/d89506834fb11c6fa0bd5d515c0dd55b13ac6958.1613674948.git.gustavo.pimentel@synopsys.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In commit 05bc1be6db ("s390/pci: create zPCI bus") we removed the
pci_dev_put() call matching the earlier pci_get_slot() done as part of
__zpci_event_availability(). This was based on the wrong understanding
that the device_put() done as part of pci_destroy_device() would counter
the pci_get_slot() when it only counters the initial reference. This
same understanding and existing bad example also lead to not doing
a pci_dev_put() in zpci_remove_device().
Since releasing the PCI devices, unlike releasing the PCI slot, does not
print any debug message for testing I added one in pci_release_dev().
This revealed that we are indeed leaking the PCI device on PCI
hotunplug. Further testing also revealed another missing pci_dev_put() in
disable_slot().
Fix this by adding the missing pci_dev_put() in disable_slot() and fix
zpci_remove_device() with the correct pci_dev_put() calls. Also instead
of calling pci_get_slot() in __zpci_event_availability() to determine if
a PCI device is registered and then doing the same again in
zpci_remove_device() do this once in zpci_remove_device() which makes
sure that the pdev in __zpci_event_availability() is only used for the
result of pci_scan_single_device() which does not need a reference count
decremnt as its ownership goes to the PCI bus.
Also move the check if zdev->zbus->bus is set into zpci_remove_device()
since it may be that we're removing a device with devfn != 0 which never
had a PCI bus. So we can still set the pdev->error_state to indicate
that the device is not usable anymore, add a flag to set the error state.
Fixes: 05bc1be6db ("s390/pci: create zPCI bus")
Cc: <stable@vger.kernel.org> # 5.8+: e1bff843cd s390/pci: remove superfluous zdev->zbus check
Cc: <stable@vger.kernel.org> # 5.8+: ba764dd703 s390/pci: refactor zpci_create_device()
Cc: <stable@vger.kernel.org> # 5.8+
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCYEsmRgAKCRCAXGG7T9hj
vsQ9AP9oN1PKbTGn9U6FR/yJtMuD2XuX8a86PnMI8iM/bnox5QEA/kLIOBknM/nF
bPDfBcb72BERKX+83qtd5153zcbhww4=
=a/rf
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.12b-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Two fix series and a single cleanup:
- a small cleanup patch to remove unneeded symbol exports
- a series to cleanup Xen grant handling (avoiding allocations in
some cases, and using common defines for "invalid" values)
- a series to address a race issue in Xen event channel handling"
* tag 'for-linus-5.12b-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
Xen/gntdev: don't needlessly use kvcalloc()
Xen/gnttab: introduce common INVALID_GRANT_{HANDLE,REF}
Xen/gntdev: don't needlessly allocate k{,un}map_ops[]
Xen: drop exports of {set,clear}_foreign_p2m_mapping()
xen/events: avoid handling the same event on two cpus at the same time
xen/events: don't unmask an event channel when an eoi is pending
xen/events: reset affinity of 2-level event when tearing it down
There are harmless warnings when compile testing the kernel with
CONFIG_TRIM_UNUSED_KSYMS:
drivers/pci/controller/dwc/pcie-al.o: no symbols
drivers/pci/controller/pci-thunder-ecam.o: no symbols
drivers/pci/controller/pci-thunder-pem.o: no symbols
The problem here is that the host drivers get built even when the
configuration symbols are all disabled, as they pretend to not be drivers
but are silently enabled because of the promise that ACPI-based systems
need no drivers.
Add back the normal symbols to have these drivers built, and change the
logic to otherwise only build them when both CONFIG_PCI_QUIRKS and
CONFIG_ACPI are enabled.
As a side-effect, this enables compile-testing the drivers on other
architectures, which in turn needs the acpi_get_rc_resources() function to
be defined.
Link: https://lore.kernel.org/r/20210308152501.2135937-3-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Robert Richter <rric@kernel.org>
Compile-testing these drivers is currently broken. Enabling it causes a
couple of build failures though:
drivers/pci/controller/pci-thunder-ecam.c:119:30: error: shift count >= width of type [-Werror,-Wshift-count-overflow]
drivers/pci/controller/pci-thunder-pem.c:54:2: error: implicit declaration of function 'writeq' [-Werror,-Wimplicit-function-declaration]
drivers/pci/controller/pci-thunder-pem.c:392:8: error: implicit declaration of function 'acpi_get_rc_resources' [-Werror,-Wimplicit-function-declaration]
Fix them with the obvious one-line changes.
Link: https://lore.kernel.org/r/20210308152501.2135937-2-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Robert Richter <rric@kernel.org>
Compile-testing this driver without ECAM support results in a link failure:
ld.lld: error: undefined symbol: pci_ecam_map_bus
>>> referenced by pcie-al.c
>>> pci/controller/dwc/pcie-al.o:(al_pcie_map_bus) in archive drivers/built-in.a
Select CONFIG_ECAM like the other drivers do.
Link: https://lore.kernel.org/r/20210308152501.2135937-1-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
It's not helpful if every driver has to cook its own. Generalize
xenbus'es INVALID_GRANT_HANDLE and pcifront's INVALID_GRANT_REF (which
shouldn't have expanded to zero to begin with). Use the constants in
p2m.c and gntdev.c right away, and update field types where necessary so
they would match with the constants' types (albeit without touching
struct ioctl_gntdev_grant_ref's ref field, as that's part of the public
interface of the kernel and would require introducing a dependency on
Xen's grant_table.h public header).
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/db7c38a5-0d75-d5d1-19de-e5fe9f0b9c48@suse.com
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
rcec_assoc_rciep() used "rciep->devfn" (a single byte encoding both the
device and function number) as the device number to check whether the
corresponding bit was set in the RCEC's Association Bitmap for RCiEPs.
But per PCIe r5.0, sec 7.9.10.2, "Association Bitmap for RCiEPs", the
32-bit bitmap contains one bit per device. That bit applies to all
functions of the device.
Fix rcec_assoc_rciep() to convert the value of "rciep->devfn" to a device
number to ensure that RCiEP devices are correctly associated with the RCEC.
Reported-and-tested-by: Wen Jin <wen.jin@intel.com>
Fixes: 507b460f81 ("PCI/ERR: Add pcie_link_rcec() to associate RCiEPs")
Link: https://lore.kernel.org/r/20210222011717.43266-1-qiuxu.zhuo@intel.com
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sean V Kelley <sean.v.kelley@intel.com>
After updating pci-dra7xx driver to probe with ti-sysc and genpd, I
noticed that dra7xx_pcie_probe() would not run if a power-domains property
was configured for the interconnect target module.
Turns out that module_platform_driver_probe uses platform_driver_probe(),
while builtin_platform_driver uses platform_driver_register().
Only platform_driver_register() works for deferred probe as noted in the
comments for __platform_driver_probe() in drivers/base/platform.c with a
line saying "Note that this is incompatible with deferred probing".
With module_platform_driver_probe, we have platform_driver_probe() produce
-ENODEV error at device_initcall() level, and no further attempts are done.
Let's fix this by using module_platform_driver instead.
Note this is not an issue currently as we probe devices with simple-bus,
and only is needed as we start probing the device with ti-sysc, or when
probed with simple-pm-bus.
Note that we must now also remove __init for probe related functions to
avoid a section mismatch warning.
Cc: linux-pci@vger.kernel.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
-----BEGIN PGP SIGNATURE-----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=GXL5
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Remove unnecessary locking around _OSC (Bjorn Helgaas)
- Clarify message about _OSC failure (Bjorn Helgaas)
- Remove notification of PCIe bandwidth changes (Bjorn Helgaas)
- Tidy checking of syscall user config accessors (Heiner Kallweit)
Resource management:
- Decline to resize resources if boot config must be preserved (Ard
Biesheuvel)
- Fix pci_register_io_range() memory leak (Geert Uytterhoeven)
Error handling (Keith Busch):
- Clear error status from the correct device
- Retain error recovery status so drivers can use it after reset
- Log the type of Port (Root or Switch Downstream) that we reset
- Always request a reset for Downstream Ports in frozen state
Endpoint framework and NTB (Kishon Vijay Abraham I):
- Make *_get_first_free_bar() take into account 64 bit BAR
- Add helper API to get the 'next' unreserved BAR
- Make *_free_bar() return error codes on failure
- Remove unused pci_epf_match_device()
- Add support to associate secondary EPC with EPF
- Add support in configfs to associate two EPCs with EPF
- Add pci_epc_ops to map MSI IRQ
- Add pci_epf_ops to expose function-specific attrs
- Allow user to create sub-directory of 'EPF Device' directory
- Implement ->msi_map_irq() ops for cadence
- Configure LM_EP_FUNC_CFG based on epc->function_num_map for cadence
- Add EP function driver to provide NTB functionality
- Add support for EPF PCI Non-Transparent Bridge
- Add specification for PCI NTB function device
- Add PCI endpoint NTB function user guide
- Add configfs binding documentation for pci-ntb endpoint function
Broadcom STB PCIe controller driver:
- Add support for BCM4908 and external PERST# signal controller
(Rafał Miłecki)
Cadence PCIe controller driver:
- Retrain Link to work around Gen2 training defect (Nadeem Athani)
- Fix merge botch in cdns_pcie_host_map_dma_ranges() (Krzysztof
Wilczyński)
Freescale Layerscape PCIe controller driver:
- Add LX2160A rev2 EP mode support (Hou Zhiqiang)
- Convert to builtin_platform_driver() (Michael Walle)
MediaTek PCIe controller driver:
- Fix OF node reference leak (Krzysztof Wilczyński)
Microchip PolarFlare PCIe controller driver:
- Add Microchip PolarFire PCIe controller driver (Daire McNamara)
Qualcomm PCIe controller driver:
- Use PHY_REFCLK_USE_PAD only for ipq8064 (Ansuel Smith)
- Add support for ddrss_sf_tbu clock for sm8250 (Dmitry Baryshkov)
Renesas R-Car PCIe controller driver:
- Drop PCIE_RCAR config option (Lad Prabhakar)
- Always allocate MSI addresses in 32bit space (Marek Vasut)
Rockchip PCIe controller driver:
- Add FriendlyARM NanoPi M4B DT binding (Chen-Yu Tsai)
- Make 'ep-gpios' DT property optional (Chen-Yu Tsai)
Synopsys DesignWare PCIe controller driver:
- Work around ECRC configuration hardware defect (Vidya Sagar)
- Drop support for config space in DT 'ranges' (Rob Herring)
- Change size to u64 for EP outbound iATU (Shradha Todi)
- Add upper limit address for outbound iATU (Shradha Todi)
- Make dw_pcie ops optional (Jisheng Zhang)
- Remove unnecessary dw_pcie_ops from al driver (Jisheng Zhang)
Xilinx Versal CPM PCIe controller driver:
- Fix OF node reference leak (Pan Bian)
Miscellaneous:
- Remove tango host controller driver (Arnd Bergmann)
- Remove IRQ handler & data together (altera-msi, brcmstb, dwc)
(Martin Kaiser)
- Fix xgene-msi race in installing chained IRQ handler (Martin
Kaiser)
- Apply CONFIG_PCI_DEBUG to entire drivers/pci hierarchy (Junhao He)
- Fix pci-bridge-emul array overruns (Russell King)
- Remove obsolete uses of WARN_ON(in_interrupt()) (Sebastian Andrzej
Siewior)"
* tag 'pci-v5.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (69 commits)
PCI: qcom: Use PHY_REFCLK_USE_PAD only for ipq8064
PCI: qcom: Add support for ddrss_sf_tbu clock
dt-bindings: PCI: qcom: Document ddrss_sf_tbu clock for sm8250
PCI: al: Remove useless dw_pcie_ops
PCI: dwc: Don't assume the ops in dw_pcie always exist
PCI: dwc: Add upper limit address for outbound iATU
PCI: dwc: Change size to u64 for EP outbound iATU
PCI: dwc: Drop support for config space in 'ranges'
PCI: layerscape: Convert to builtin_platform_driver()
PCI: layerscape: Add LX2160A rev2 EP mode support
dt-bindings: PCI: layerscape: Add LX2160A rev2 compatible strings
PCI: dwc: Work around ECRC configuration issue
PCI/portdrv: Report reset for frozen channel
PCI/AER: Specify the type of Port that was reset
PCI/ERR: Retain status from error notification
PCI/AER: Clear AER status from Root Port when resetting Downstream Port
PCI/ERR: Clear status of the reporting device
dt-bindings: arm: rockchip: Add FriendlyARM NanoPi M4B
PCI: rockchip: Make 'ep-gpios' DT property optional
Documentation: PCI: Add PCI endpoint NTB function user guide
...
- Remove IRQ handler & data together for altera, brcmstb, dwc (Martin
Kaiser)
- Fix xgene race in installing chained IRQ handler (Martin Kaiser)
- Drop PCIE_RCAR config option (replaced by PCIE_RCAR_HOST) (Lad Prabhakar)
- Fix xgene comment about CRS vs CRS SV (Bjorn Helgaas)
* remotes/lorenzo/pci/misc:
PCI: hv: Fix typo
PCI: xgene: Fix CRS SV comment
PCI: brcmstb: Remove chained IRQ handler and data in one go
PCI: Drop PCIE_RCAR config option
PCI: xgene-msi: Fix race in installing chained irq handler
PCI: dwc: Remove IRQ handler and data in one go
PCI: altera-msi: Remove IRQ handler and data in one go
- Always allocate rcar MSI addresses in 32-bit space so legacy devices
without 64-bit MSI support can use MSI (Marek Vasut)
* remotes/lorenzo/pci/rcar:
PCI: rcar: Always allocate MSI addresses in 32bit space
- Add support for SM8250 PCIe SF TBU clock (Dmitry Baryshkov)
- Use PHY_REFCLK_USE_PAD only for qcom ipq8064 (Ansuel Smith)
* pci/qcom:
PCI: qcom: Use PHY_REFCLK_USE_PAD only for ipq8064
PCI: qcom: Add support for ddrss_sf_tbu clock
dt-bindings: PCI: qcom: Document ddrss_sf_tbu clock for sm8250
- Account for 64-bit BARs in pci_epc_get_first_free_bar() (Kishon Vijay
Abraham I)
- Add pci_epc_get_next_free_bar() helper (Kishon Vijay Abraham I)
- Return error codes on failure of endpoint BAR interfaces (Kishon Vijay
Abraham I)
- Remove unused pci_epf_match_device() (Kishon Vijay Abraham I)
- Add support for secondary endpoint controller to prepare for NTB endpoint
functionality (Kishon Vijay Abraham I)
- Add configfs support for secondary endpoint controller (Kishon Vijay
Abraham I)
- Add MSI address mapping ops for NTB doorbell support (Kishon Vijay
Abraham I)
- Add ops for endpoint function-specific attributes (Kishon Vijay Abraham
I)
- Allow configfs subdirectory for endpoint function configuration (Kishon
Vijay Abraham I)
- Implement cadence MSI address mapping ops (Kishon Vijay Abraham I)
- Configure cadence LM_EP_FUNC_CFG based on epc->function_num_map (Kishon
Vijay Abraham I)
- Add endpoint-side driver to provide NTB functionality (Kishon Vijay
Abraham I)
- Add host-side driver for generic EPF NTB functionality (Kishon Vijay
Abraham I)
- Document NTB endpoint functionality (Kishon Vijay Abraham I)
* pci/ntb:
Documentation: PCI: Add PCI endpoint NTB function user guide
Documentation: PCI: Add configfs binding documentation for pci-ntb endpoint function
NTB: Add support for EPF PCI Non-Transparent Bridge
PCI: Add TI J721E device to PCI IDs
PCI: endpoint: Add EP function driver to provide NTB functionality
PCI: cadence: Configure LM_EP_FUNC_CFG based on epc->function_num_map
PCI: cadence: Implement ->msi_map_irq() ops
PCI: endpoint: Allow user to create sub-directory of 'EPF Device' directory
PCI: endpoint: Add pci_epf_ops to expose function-specific attrs
PCI: endpoint: Add pci_epc_ops to map MSI IRQ
PCI: endpoint: Add support in configfs to associate two EPCs with EPF
PCI: endpoint: Add support to associate secondary EPC with EPF
PCI: endpoint: Remove unused pci_epf_match_device()
PCI: endpoint: Make *_free_bar() to return error codes on failure
PCI: endpoint: Add helper API to get the 'next' unreserved BAR
PCI: endpoint: Make *_get_first_free_bar() take into account 64 bit BAR
Documentation: PCI: Add specification for the PCI NTB function device
- Always set DesignWare "TLP Digest" bit so generic code can enable ECRC
via the AER Capability (Vidya Sagar)
- Drop support for config space in DT 'ranges' (Rob Herring)
- Increase width of outbound iATU size to u64 (Shradha Todi)
- Add upper limit address for outbound iATU (Shradha Todi)
- Allow dwc-based drivers that don't override any default ops (Jisheng
Zhang)
- Drop unnecessary dw_pcie_ops from the al driver (Jisheng Zhang)
* pci/dwc:
PCI: al: Remove useless dw_pcie_ops
PCI: dwc: Don't assume the ops in dw_pcie always exist
PCI: dwc: Add upper limit address for outbound iATU
PCI: dwc: Change size to u64 for EP outbound iATU
PCI: dwc: Drop support for config space in 'ranges'
PCI: dwc: Work around ECRC configuration issue
- Retrain Link to work around Gen2 training defect (Nadeem Athani)
* remotes/lorenzo/pci/cadence:
PCI: cadence: Retrain Link to work around Gen2 training defect
- Add support for BCM4908 with external PERST# signal controller (Rafał
Miłecki)
* remotes/lorenzo/pci/brcmstb:
PCI: brcmstb: support BCM4908 with external PERST# signal controller
dt-bindings: PCI: brcmstb: add BCM4908 binding
- Decline requests to resize BARs if platform requires us to preserve
resource assignments (Ard Biesheuvel)
* pci/resource:
PCI: Decline to resize resources if boot config must be preserved
- Clear AER status of the reporting device (Keith Busch)
- Clear AER status from Root Port when resetting Downstream Port (Keith
Busch)
- Retain status from error notification (Keith Busch)
- Log the type of Port that was reset for error handling (Keith Busch)
- Report reset for frozen channel (Keith Busch)
* pci/error:
PCI/portdrv: Report reset for frozen channel
PCI/AER: Specify the type of Port that was reset
PCI/ERR: Retain status from error notification
PCI/AER: Clear AER status from Root Port when resetting Downstream Port
PCI/ERR: Clear status of the reporting device
The use of PHY_REFCLK_USE_PAD introduced a regression for apq8064 devices.
It was tested that while apq doesn't require the padding, ipq SoC must use
it or the kernel hangs on boot.
Link: https://lore.kernel.org/r/20201019165555.8269-1-ansuelsmth@gmail.com
Fixes: de3c4bf648 ("PCI: qcom: Add support for tx term offset for rev 2.1.0")
Reported-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: stable@vger.kernel.org # v4.19+
We have removed the assumption that dw_pcie_ops always exists in the dwc
core driver, so we can remove the useless dw_pcie_ops now.
Link: https://lore.kernel.org/r/20210128144324.2fa8577c@xhacker.debian
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jonathan Chocron <jonnyc@amazon.com>
Some dwc-based device drivers, especially host-only drivers, may work well
with the default read_dbi/write_dbi/link_up implementations in
pcie-designware.c, so remove the assumption that every driver implements
them to simplify those drivers.
Link: https://lore.kernel.org/r/20210128144258.10329aa4@xhacker.debian
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The size parameter is unsigned long type which can accept size > 4GB. In
that case, the upper limit address must be programmed. Add support to
program the upper limit address and set INCREASE_REGION_SIZE in case size >
4GB.
Link: https://lore.kernel.org/r/1612250918-19610-1-git-send-email-shradha.t@samsung.com
Signed-off-by: Shradha Todi <shradha.t@samsung.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Since outbound iATU permits size to be greater than 4GB for which the
support is also available, allow EP function to send u64 size instead of
truncating to u32.
Link: https://lore.kernel.org/r/1609929900-19082-1-git-send-email-shradha.t@samsung.com
Signed-off-by: Shradha Todi <shradha.t@samsung.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Since commit a0fd361db8 ("PCI: dwc: Move "dbi", "dbi2", and
"addr_space" resource setup into common code"), the code
setting dbi_base when the config space is defined in 'ranges' property
instead of 'reg' is dead code as dbi_base is never NULL.
Rather than fix this, let's just drop the code. Using ranges has been
deprecated since 2014. The only platforms using this were exynos5440,
i.MX6 and Spear13xx. Exynos5440 is dead and has been removed. i.MX6 and
Spear13xx had PCIe support added just before this was deprecated and
were fixed within a kernel release or 2.
Link: https://lore.kernel.org/r/20201215194149.86831-1-robh@kernel.org
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
fw_devlink will defer the probe until all suppliers are ready. We can't
use builtin_platform_driver_probe() because it doesn't retry after probe
deferral. Convert it to builtin_platform_driver().
Link: https://lore.kernel.org/r/20210120105246.23218-1-michael@walle.cc
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The LX2160A rev2 uses the same PCIe IP as LS2088A, but LX2160A rev2 PCIe
controller is integrated with different stride between PFs' register
address.
Link: https://lore.kernel.org/r/20201026051448.1913-2-Zhiqiang.Hou@nxp.com
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
DesignWare core has a TLP digest (TD) override bit in one of the control
registers of ATU. This bit also needs to be programmed for proper ECRC
functionality. This is currently identified as an issue with DesignWare
IP version 4.90a.
[bhelgaas: fix typos/grammar errors]
Link: https://lore.kernel.org/r/20201230165723.673-1-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI error recovery always resets the link for a frozen state, so the
port driver should return that a reset is required for its result. This
will get the .slot_reset() callback invoked, which is necessary to
restore the port's config space. Without this, the driver had been
relying on downstream drivers to return this status.
Link: https://lore.kernel.org/r/20210104230300.1277180-6-kbusch@kernel.org
Tested-by: Hedi Berriche <hedi.berriche@hpe.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Hedi Berriche <hedi.berriche@hpe.com>
The AER driver may be called upon to reset either a Downstream or a Root
Port. Check which type it is to properly identify it when logging that
the reset occurred.
Link: https://lore.kernel.org/r/20210104230300.1277180-5-kbusch@kernel.org
Tested-by: Hedi Berriche <hedi.berriche@hpe.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Hedi Berriche <hedi.berriche@hpe.com>
Overwriting the frozen detected status with the result of the link reset
loses the NEED_RESET result that drivers are depending on for error
handling to report the .slot_reset() callback. Retain this status so
that subsequent error handling has the correct flow.
Link: https://lore.kernel.org/r/20210104230300.1277180-4-kbusch@kernel.org
Reported-by: Hinko Kocevar <hinko.kocevar@ess.eu>
Tested-by: Hedi Berriche <hedi.berriche@hpe.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Sean V Kelley <sean.v.kelley@intel.com>
Acked-by: Hedi Berriche <hedi.berriche@hpe.com>
The pci_dev parameter given to aer_root_reset() may be a Downstream Port
rather than the Root Port. Get the Root Port from the provided device in
order to clear the root's AER status.
Link: https://lore.kernel.org/r/20210104230300.1277180-3-kbusch@kernel.org
Tested-by: Hedi Berriche <hedi.berriche@hpe.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Sean V Kelley <sean.v.kelley@intel.com>
Acked-by: Hedi Berriche <hedi.berriche@hpe.com>
Error handling operates on the first Downstream Port above the detected
error, but the error may have been reported by a downstream device.
Clear the AER status of the device that reported the error rather than
the first Downstream Port.
Link: https://lore.kernel.org/r/20210104230300.1277180-2-kbusch@kernel.org
Tested-by: Hedi Berriche <hedi.berriche@hpe.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Sean V Kelley <sean.v.kelley@intel.com>
Acked-by: Hedi Berriche <hedi.berriche@hpe.com>
The Rockchip PCIe controller DT binding clearly states that 'ep-gpios' is
an optional property. And indeed there are boards that don't require it.
Make the driver follow the binding by using devm_gpiod_get_optional()
instead of devm_gpiod_get().
[bhelgaas: tidy whitespace]
Link: https://lore.kernel.org/r/20210121162321.4538-2-wens@kernel.org
Fixes: e77f847df5 ("PCI: rockchip: Add Rockchip PCIe controller support")
Fixes: 956cd99b35 ("PCI: rockchip: Separate common code from RC driver")
Fixes: 964bac9455 ("PCI: rockchip: Split out rockchip_pcie_parse_dt() to parse DT")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a new endpoint function driver to provide NTB functionality using
multiple PCIe endpoint instances.
[arnd@arndb.de: Select configfs dependency]
[yebin10@huawei.com: Fix unused but set variables]
[geert+renesas@glider.be: Explain NTB in PCI_EPF_NTB help text]
Link: https://lore.kernel.org/r/20210201195809.7342-14-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The number of functions supported by the endpoint controller is configured
in LM_EP_FUNC_CFG based on func_no member of struct pci_epf. Now that an
endpoint function can be associated with two endpoint controllers (primary
and secondary), just using func_no will not suffice as that will take into
account only if the endpoint controller is associated with the primary
interface of endpoint function. Instead use epc->function_num_map which
will already have the configured functions information (irrespective of
whether the endpoint controller is associated with primary or secondary
interface).
Link: https://lore.kernel.org/r/20210201195809.7342-13-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tom Joseph <tjoseph@cadence.com>
Implement ->msi_map_irq() ops in order to map physical address to MSI
address and return MSI data.
Link: https://lore.kernel.org/r/20210201195809.7342-12-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tom Joseph <tjoseph@cadence.com>
Documentation/PCI/endpoint/pci-endpoint-cfs.rst explains how a user has to
create a directory in-order to create a 'EPF Device' that can be
configured/probed by 'EPF Driver'.
Allow user to create a sub-directory of 'EPF Device' directory for any
function specific attributes that has to be exposed to the user.
Link: https://lore.kernel.org/r/20210201195809.7342-11-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In addition to the attributes that are generic across function drivers
documented in Documentation/PCI/endpoint/pci-endpoint-cfs.rst, there could
be function-specific attributes that has to be exposed by the function
driver to be configured by the user. Add ->add_cfs() in pci_epf_ops to be
populated by the function driver if it has to expose any function-specific
attributes and pci_epf_type_add_cfs() to be invoked by pci-ep-cfs.c when
sub-directory to main function directory is created.
Link: https://lore.kernel.org/r/20210201195809.7342-10-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add pci_epc_ops to map physical address to MSI address and return MSI data.
The physical address is an address in the outbound region. This is required
to implement doorbell functionality of NTB (non-transparent bridge) wherein
EPC on either side of the interface (primary and secondary) can directly
write to the physical address (in outbound region) of the other interface
to ring doorbell using MSI.
Link: https://lore.kernel.org/r/20210201195809.7342-9-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Now that PCI endpoint core supports to add secondary endpoint controller
(EPC) with endpoint function (EPF), Add support in configfs to associate
two EPCs with EPF. This creates "primary" and "secondary" directory inside
the directory created by users for EPF device. Users have to add a symlink
of endpoint controller (pci_ep/controllers/) to "primary" or "secondary"
directory to bind EPF to primary and secondary EPF interfaces respectively.
Existing method of linking directory representing EPF device to directory
representing EPC device to associate a single EPC device with a EPF device
will continue to work.
Link: https://lore.kernel.org/r/20210201195809.7342-8-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In the case of standard endpoint functions, only one endpoint controller
(EPC) will be associated with an endpoint function (EPF). However for
providing NTB (non transparent bridge) functionality, two EPCs should be
associated with a single EPF. Add support to associate secondary EPC with
EPF. This is in preparation for adding NTB endpoint function driver.
Link: https://lore.kernel.org/r/20210201195809.7342-7-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove unused pci_epf_match_device() function added in pci-epf-core.c
Link: https://lore.kernel.org/r/20210201195809.7342-6-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Modify pci_epc_get_next_free_bar() and pci_epc_get_first_free_bar() to
return error values if there are no free BARs available.
Link: https://lore.kernel.org/r/20210201195809.7342-5-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add an API to get the next unreserved BAR starting from a given BAR number
that can be used by the endpoint function.
Link: https://lore.kernel.org/r/20210201195809.7342-4-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_epc_get_first_free_bar() uses only "reserved_bar" member in
epc_features to get the first unreserved BAR. However if the reserved BAR
is also a 64-bit BAR, then the next BAR shouldn't be returned (since 64-bit
BAR uses two BARs).
Make pci_epc_get_first_free_bar() take into account 64 bit BAR while
returning the first free unreserved BAR.
Link: https://lore.kernel.org/r/20210201195809.7342-3-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add support for the Microchip PolarFire PCIe controller when configured in
host (Root Complex) mode.
[bhelgaas: wrap lines to fit in 80 columns, fix trivial style issues]
Link: https://lore.kernel.org/r/20210125162934.5335-4-daire.mcnamara@microchip.com
Signed-off-by: Daire McNamara <daire.mcnamara@microchip.com>
[lorenzo.pieralisi@arm.com: minor comments tweak]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Many drivers can now use pci_host_common_probe() directly.
Their hardware window setup can be moved from their 'custom' probe
functions to individual driver init functions.
Link: https://lore.kernel.org/r/20210125162934.5335-2-daire.mcnamara@microchip.com
Signed-off-by: Daire McNamara <daire.mcnamara@microchip.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
- replace mm/frame_vector.c by get_user_pages in misc/habana and
drm/exynos drivers, then move that into media as it's sole user
- close race in generic_access_phys
- s390 pci ioctl fix of this series landed in 5.11 already
- properly revoke iomem mappings (/dev/mem, pci files)
-----BEGIN PGP SIGNATURE-----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=lQoR
-----END PGP SIGNATURE-----
Merge tag 'topic/iomem-mmap-vs-gup-2021-02-22' of git://anongit.freedesktop.org/drm/drm
Pull follow_pfn() updates from Daniel Vetter:
"Fixes around VM_FPNMAP and follow_pfn:
- replace mm/frame_vector.c by get_user_pages in misc/habana and
drm/exynos drivers, then move that into media as it's sole user
- close race in generic_access_phys
- s390 pci ioctl fix of this series landed in 5.11 already
- properly revoke iomem mappings (/dev/mem, pci files)"
* tag 'topic/iomem-mmap-vs-gup-2021-02-22' of git://anongit.freedesktop.org/drm/drm:
PCI: Revoke mappings like devmem
PCI: Also set up legacy files only after sysfs init
sysfs: Support zapping of binary attr mmaps
resource: Move devmem revoke code to resource framework
/dev/mem: Only set filp->f_mapping
PCI: Obey iomem restrictions for procfs mmap
mm: Close race in generic_access_phys
media: videobuf2: Move frame_vector into media subsystem
mm/frame-vector: Use FOLL_LONGTERM
misc/habana: Use FOLL_LONGTERM for userptr
misc/habana: Stop using frame_vector helpers
drm/exynos: Use FOLL_LONGTERM for g2d cmdlists
drm/exynos: Stop using frame_vector helpers
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEIbPD0id6easf0xsudhRwX5BBoF4FAmArly8THHdlaS5saXVA
a2VybmVsLm9yZwAKCRB2FHBfkEGgXkRfCADB0PA4xlfVF0Na/iZoBFdNFr3EMU4K
NddGJYyk0o+gipUIj2xu7TksVw8c1/cWilXOUBe7oZRKw2/fC/0hpDwvLpPtD/wP
+Tc2DcIgwquMvsSksyqpMOb0YjNNhWCx9A9xPWawpUdg20IfbK/ekRHlFI5MsEww
7tFS+MHY4QbsPv0WggoK61PGnhGCBt/85Lv4I08ZGohA6uirwC4fNIKp83SgFNtf
1hHbvpapAFEXwZiKFbzwpue20jWJg+tlTiEFpen3exjBICoagrLLaz3F0SZJvbxl
2YY32zbBsQe4Izre5PVuOlMoNFRom9NSzEzdZT10g7HNtVrwKVNLcohS
=MyO4
-----END PGP SIGNATURE-----
Merge tag 'hyperv-next-signed-20210216' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull Hyper-V updates from Wei Liu:
- VMBus hardening patches from Andrea Parri and Andres Beltran.
- Patches to make Linux boot as the root partition on Microsoft
Hypervisor from Wei Liu.
- One patch to add a new sysfs interface to support hibernation on
Hyper-V from Dexuan Cui.
- Two miscellaneous clean-up patches from Colin and Gustavo.
* tag 'hyperv-next-signed-20210216' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux: (31 commits)
Revert "Drivers: hv: vmbus: Copy packets sent by Hyper-V out of the ring buffer"
iommu/hyperv: setup an IO-APIC IRQ remapping domain for root partition
x86/hyperv: implement an MSI domain for root partition
asm-generic/hyperv: import data structures for mapping device interrupts
asm-generic/hyperv: introduce hv_device_id and auxiliary structures
asm-generic/hyperv: update hv_interrupt_entry
asm-generic/hyperv: update hv_msi_entry
x86/hyperv: implement and use hv_smp_prepare_cpus
x86/hyperv: provide a bunch of helper functions
ACPI / NUMA: add a stub function for node_to_pxm()
x86/hyperv: handling hypercall page setup for root
x86/hyperv: extract partition ID from Microsoft Hypervisor if necessary
x86/hyperv: allocate output arg pages if required
clocksource/hyperv: use MSR-based access if running as root
Drivers: hv: vmbus: skip VMBus initialization if Linux is root
x86/hyperv: detect if Linux is the root partition
asm-generic/hyperv: change HV_CPU_POWER_MANAGEMENT to HV_CPU_MANAGEMENT
hv: hyperv.h: Replace one-element array with flexible-array in struct icmsg_negotiate
hv_netvsc: Restrict configurations on isolated guests
Drivers: hv: vmbus: Enforce 'VMBus version >= 5.2' on isolated guests
...
Remove the 'acpiphp_callback' typedef as it is not used.
Link: https://lore.kernel.org/r/1613443120-4279-1-git-send-email-chen45464546@163.com
Signed-off-by: Chen Lin <chen.lin5@zte.com.cn>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Function cdns_pcie_host_map_dma_ranges() iterates over a PCIe host bridge
DMA ranges using the resource_list_for_each_entry() iterator, returning an
error if cdns_pcie_host_bar_config() fails.
49e427e6bd ("Merge branch 'pci/host-probe-refactor'") botched a merge so
it *always* returned after the first DMA range, even if no error occurred.
Fix the error checking so we return early only when an error occurs.
[bhelgaas: commit log]
Fixes: 49e427e6bd ("Merge branch 'pci/host-probe-refactor'")
Link: https://lore.kernel.org/r/20210216205935.3112661-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Kmemleak reports:
unreferenced object 0xc328de40 (size 64):
comm "kworker/1:1", pid 21, jiffies 4294938212 (age 1484.670s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 e0 d8 fc eb 00 00 00 00 ................
00 00 10 fe 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ad758d10>] pci_register_io_range+0x3c/0x80
[<2c7f139e>] of_pci_range_to_resource+0x48/0xc0
[<f079ecc8>] devm_of_pci_get_host_bridge_resources.constprop.0+0x2ac/0x3ac
[<e999753b>] devm_of_pci_bridge_init+0x60/0x1b8
[<a895b229>] devm_pci_alloc_host_bridge+0x54/0x64
[<e451ddb0>] rcar_pcie_probe+0x2c/0x644
In case a PCI host driver's probe is deferred, the same I/O range may be
allocated again, and be ignored, causing a memory leak.
Fix this by (a) letting logic_pio_register_range() return -EEXIST if the
passed range already exists, so pci_register_io_range() will free it, and
by (b) making pci_register_io_range() not consider -EEXIST an error
condition.
Link: https://lore.kernel.org/r/20210202100332.829047-1-geert+renesas@glider.be
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We allow up to PCI_EXP_SLTSTA2 registers to be accessed, but the
pcie_cap_regs_behavior[] array only covers up to PCI_EXP_RTSTA. Expand
this array to avoid walking off the end of it.
Do the same for pci_regs_behavior for consistency[], and add a
BUILD_BUG_ON() to also check the bridge->conf structure size.
Fixes: 23a5fba4d9 ("PCI: Introduce PCI bridge emulated config space common logic")
Link: https://lore.kernel.org/r/E1l6z9W-0006Re-MQ@rmk-PC.armlinux.org.uk
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Since 3234ac664a ("/dev/mem: Revoke mappings when a driver claims
the region") /dev/kmem zaps PTEs when the kernel requests exclusive
acccess to an iomem region. And with CONFIG_IO_STRICT_DEVMEM, this is
the default for all driver uses.
Except there are two more ways to access PCI BARs: sysfs and proc mmap
support. Let's plug that hole.
For revoke_devmem() to work we need to link our vma into the same
address_space, with consistent vma->vm_pgoff. ->pgoff is already
adjusted, because that's how (io_)remap_pfn_range works, but for the
mapping we need to adjust vma->vm_file->f_mapping. The cleanest way is
to adjust this at at ->open time:
- for sysfs this is easy, now that binary attributes support this. We
just set bin_attr->mapping when mmap is supported
- for procfs it's a bit more tricky, since procfs PCI access has only
one file per device, and access to a specific resource first needs
to be set up with some ioctl calls. But mmap is only supported for
the same resources as sysfs exposes with mmap support, and otherwise
rejected, so we can set the mapping unconditionally at open time
without harm.
A special consideration is for arch_can_pci_mmap_io() - we need to
make sure that the ->f_mapping doesn't alias between ioport and iomem
space. There are only 2 ways in-tree to support mmap of ioports: generic
PCI mmap (ARCH_GENERIC_PCI_MMAP_RESOURCE), and sparc as the single
architecture hand-rolling. Both approaches support ioport mmap through a
special PFN range and not through magic PTE attributes. Aliasing is
therefore not a problem.
The only difference in access checks left is that sysfs PCI mmap does
not check for CAP_RAWIO. I'm not really sure whether that should be
added or not.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Kees Cook <keescook@chromium.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Jérôme Glisse <jglisse@redhat.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-mm@kvack.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-media@vger.kernel.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20210204165831.2703772-3-daniel.vetter@ffwll.ch
We are already doing this for all the regular sysfs files on PCI
devices, but not yet on the legacy io files on the PCI buses. Thus far
no problem, but in the next patch I want to wire up iomem revoke
support. That needs the vfs up and running already to make sure that
iomem_get_mapping() works.
Wire it up exactly like the existing code in
pci_create_sysfs_dev_files(). Note that pci_remove_legacy_files()
doesn't need a check since the one for pci_bus->legacy_io is
sufficient.
An alternative solution would be to implement a callback in sysfs to
set up the address space from iomem_get_mapping() when userspace calls
mmap(). This also works, but Greg didn't really like that just to work
around an ordering issue when the kernel loads initially.
v2: Improve commit message (Bjorn)
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Kees Cook <keescook@chromium.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Jérôme Glisse <jglisse@redhat.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-mm@kvack.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-media@vger.kernel.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20210205133632.2827730-1-daniel.vetter@ffwll.ch
We will soon use the same structure to handle IO-APIC interrupts as
well. Introduce an enum to identify the source and a data structure for
IO-APIC RTE.
While at it, update pci-hyperv.c to use the enum.
No functional change.
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20210203150435.27941-13-wei.liu@kernel.org
WARN_ON(in_interrupt()) is used for historic reasons to ensure proper usage
of down_read() and predates might_sleep() and lockdep.
down_read() has might_sleep() which also catches users from preemption
disabled regions while in_interrupt() does not.
Remove WARN_ON(in_interrupt()) because there are now better debugging
facilities.
Link: https://lore.kernel.org/r/20210208194400.384003-1-bigeasy@linutronix.de
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cadence controller will not initiate autonomous speed change if strapped
as Gen2. The Retrain Link bit is set as quirk to enable this speed change.
Link: https://lore.kernel.org/r/20210209144622.26683-3-nadeem@cadence.com
Signed-off-by: Nadeem Athani <nadeem@cadence.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
CONFIG_PCI_DEBUG=y adds -DDEBUG to CFLAGS, which enables things like
pr_debug() and dev_dbg() (and hence pci_dbg()). Previously we added
-DDEBUG for files in drivers/pci/, but not files in subdirectories of
drivers/pci/.
Add -DDEBUG to CFLAGS for all files below drivers/pci/ so CONFIG_PCI_DEBUG
applies to the entire hierarchy.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/1612438215-33105-1-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Junhao He <hejunhao2@hisilicon.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
The PCIe Bandwidth Change Notification feature logs messages when the link
bandwidth changes. Some users have reported that these messages occur
often enough to significantly reduce NVMe performance. GPUs also seem to
generate these messages.
We don't know why the link bandwidth changes, but in the reported cases
there's no indication that it's caused by hardware failures.
Remove the bandwidth change notifications for now. Hopefully we can add
this back when we have a better understanding of why this happens and how
we can make the messages useful instead of overwhelming.
Link: https://lore.kernel.org/r/20200115221008.GA191037@google.com/
Link: https://lore.kernel.org/r/155605909349.3575.13433421148215616375.stgit@gimli.home/
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206197
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Configuration Request Retry Status ("CRS") must be supported by all PCIe
devices. CRS Software Visibility is an optional feature that enables a
Root Port to make CRS visible to software by returning a special data value
to complete a config read.
Clarify a comment to say that it is "CRS SV", not "CRS", that can be
enabled.
Link: https://lore.kernel.org/r/20210126213503.2922848-1-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
After 34e3207205 ("PCI: handle positive error codes"),
pci_user_read_config_*() and pci_user_write_config_*() return 0 or negative
errno values, not PCIBIOS_* values like PCIBIOS_SUCCESSFUL or
PCIBIOS_BAD_REGISTER_NUMBER.
Remove comparisons with PCIBIOS_SUCCESSFUL and check only for non-zero. It
happens that PCIBIOS_SUCCESSFUL is zero, so this is not a functional
change, but it aligns this code with the user accessors.
[bhelgaas: commit log]
Fixes: 34e3207205 ("PCI: handle positive error codes")
Link: https://lore.kernel.org/r/f1220314-e518-1e18-bf94-8e6f8c703758@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The for_each_available_child_of_node helper internally makes use of the
of_get_next_available_child() which performs an of_node_get() on each
iteration when searching for next available child node.
Should an available child node be found, then it would return a device
node pointer with reference count incremented, thus early return from
the middle of the loop requires an explicit of_node_put() to prevent
reference count leak.
To stop the reference leak, explicitly call of_node_put() before
returning after an error occurred.
Link: https://lore.kernel.org/r/20210120184810.3068794-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Also drop the reference count of the node on error path.
Link: https://lore.kernel.org/r/20210120143745.699-1-bianpan2016@163.com
Fixes: 508f610648 ("PCI: xilinx-cpm: Add Versal CPM Root Port driver")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The tango platform is getting removed, so the driver is no
longer needed.
Link: https://lore.kernel.org/r/20210120150800.1650898-1-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Mans Rullgard <mans@mansr.com>
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
Cc: Mans Rullgard <mans@mansr.com>
Call irq_set_chained_handler_and_data() to clear the chained handler
and the handler's data under irq_desc->lock.
See also 2cf5a03cb2 ("PCI/keystone: Fix race in installing chained
IRQ handler").
Link: https://lore.kernel.org/r/20210115211532.19837-1-martin@kaiser.cx
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
All the defconfig files have replaced PCIE_RCAR config option with
PCIE_RCAR_HOST config option which built the same driver, so we can
now safely drop PCIE_RCAR config option.
Link: https://lore.kernel.org/r/20201229170848.18482-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
BCM4908 uses external MISC block for controlling PERST# signal. Use it
as a reset controller.
Link: https://lore.kernel.org/r/20201210180421.7230-3-zajec5@gmail.com
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Fix a race where a pending interrupt could be received and the handler
called before the handler's data has been setup, by converting to
irq_set_chained_handler_and_data().
See also 2cf5a03cb2 ("PCI/keystone: Fix race in installing chained IRQ
handler").
Based on the mail discussion, it seems ok to drop the error handling.
Link: https://lore.kernel.org/r/20210115212435.19940-3-martin@kaiser.cx
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Call irq_set_chained_handler_and_data() to clear the chained handler
and the handler's data under irq_desc->lock.
See also 2cf5a03cb2 ("PCI/keystone: Fix race in installing chained
IRQ handler").
Link: https://lore.kernel.org/r/20210115212435.19940-2-martin@kaiser.cx
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Call irq_set_chained_handler_and_data() to clear the chained handler
and the handler's data under irq_desc->lock.
See also 2cf5a03cb2 ("PCI/keystone: Fix race in installing chained
IRQ handler").
Link: https://lore.kernel.org/r/20210115212435.19940-1-martin@kaiser.cx
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
This fixes MSI operation on legacy PCI cards, which cannot issue 64bit MSIs.
The R-Car controller only has one MSI trigger address instead of two, one
for 64bit and one for 32bit MSI, set the address to 32bit PCIe space so that
legacy PCI cards can also trigger MSIs.
Link: https://lore.kernel.org/r/20201016120431.7062-1-marek.vasut@gmail.com
Fixes: 290c1fb358 ("PCI: rcar: Add MSI support for PCIe")
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: linux-renesas-soc@vger.kernel.org
The _DSM #5 method in the ACPI host bridge object tells us whether the OS
must preserve the resource assignments done by firmware. If this is the
case, we should not permit drivers to resize BARs on the fly. Make
pci_resize_resource() take this into account.
Link: https://lore.kernel.org/r/20210109095353.13417-1-ardb@kernel.org
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v5.4+
There's three ways to access PCI BARs from userspace: /dev/mem, sysfs
files, and the old proc interface. Two check against
iomem_is_exclusive, proc never did. And with CONFIG_IO_STRICT_DEVMEM,
this starts to matter, since we don't want random userspace having
access to PCI BARs while a driver is loaded and using it.
Fix this by adding the same iomem_is_exclusive() check we already have
on the sysfs side in pci_mmap_resource().
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
References: 90a545e981 ("restrict /dev/mem to idle io memory ranges")
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Kees Cook <keescook@chromium.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Jérôme Glisse <jglisse@redhat.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: linux-mm@kvack.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-media@vger.kernel.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20201127164131.2244124-9-daniel.vetter@ffwll.ch
RX 5600 XT Pulse advertises support for BAR 0 being 256MB, 512MB,
or 1GB, but it also supports 2GB, 4GB, and 8GB. Add a rebar
size quirk so that the BAR 0 is big enough to cover complete VARM.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20210107175017.15893-5-nirmoy.das@amd.com
Users of pci_resize_resource() need a way to calculate BAR size
from desired bytes. Add a helper function and export it so that
modular drivers can use it.
Signed-off-by: Darren Salt <devspam@moreofthesa.me.uk>
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20210107175017.15893-3-nirmoy.das@amd.com
Commit 660c486590 ("PCI: dwc: Set 32-bit DMA mask for MSI target address
allocation") added dma_mask_set() call to explicitly set 32-bit DMA mask
for MSI message mapping, but for now it throws a warning on ret == 0, while
dma_set_mask() returns 0 in case of success.
Fix this by inverting the condition.
[bhelgaas: join string to make it greppable]
Fixes: 660c486590 ("PCI: dwc: Set 32-bit DMA mask for MSI target address allocation")
Link: https://lore.kernel.org/r/20201222150708.67983-1-alobakin@pm.me
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit b9ac0f9dc8 ("PCI: dwc: Move dw_pcie_setup_rc() to DWC common
code") broke enumeration of downstream devices on Tegra:
In non-working case (next-20201211):
0001:00:00.0 PCI bridge: NVIDIA Corporation Device 1ad2 (rev a1)
0001:01:00.0 SATA controller: Marvell Technology Group Ltd. Device 9171 (rev 13)
0005:00:00.0 PCI bridge: NVIDIA Corporation Device 1ad0 (rev a1)
In working case (v5.10-rc7):
0001:00:00.0 PCI bridge: Molex Incorporated Device 1ad2 (rev a1)
0001:01:00.0 SATA controller: Marvell Technology Group Ltd. Device 9171 (rev 13)
0005:00:00.0 PCI bridge: Molex Incorporated Device 1ad0 (rev a1)
0005:01:00.0 PCI bridge: PLX Technology, Inc. Device 3380 (rev ab)
0005:02:02.0 PCI bridge: PLX Technology, Inc. Device 3380 (rev ab)
0005:03:00.0 USB controller: PLX Technology, Inc. Device 3380 (rev ab)
The problem seems to be dw_pcie_setup_rc() is now called twice before and
after the link up handling. The fix is to move Tegra's link up handling to
.start_link() function like other DWC drivers. Tegra is a bit more
complicated than others as it re-inits the whole DWC controller to retry
the link. With this, the initialization ordering is restored to match the
prior sequence.
Fixes: b9ac0f9dc8 ("PCI: dwc: Move dw_pcie_setup_rc() to DWC common code")
Link: https://lore.kernel.org/r/20201218143905.1614098-1-robh@kernel.org
Reported-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Tested-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Vidya Sagar <vidyas@nvidia.com>
accesses, inefficient and disfunctional code. The goal is to remove the
export of irq_to_desc() to prevent these things from creeping up again.
-----BEGIN PGP SIGNATURE-----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=BXv+
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2020-12-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"This is the second attempt after the first one failed miserably and
got zapped to unblock the rest of the interrupt related patches.
A treewide cleanup of interrupt descriptor (ab)use with all sorts of
racy accesses, inefficient and disfunctional code. The goal is to
remove the export of irq_to_desc() to prevent these things from
creeping up again"
* tag 'irq-core-2020-12-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (30 commits)
genirq: Restrict export of irq_to_desc()
xen/events: Implement irq distribution
xen/events: Reduce irq_info:: Spurious_cnt storage size
xen/events: Only force affinity mask for percpu interrupts
xen/events: Use immediate affinity setting
xen/events: Remove disfunct affinity spreading
xen/events: Remove unused bind_evtchn_to_irq_lateeoi()
net/mlx5: Use effective interrupt affinity
net/mlx5: Replace irq_to_desc() abuse
net/mlx4: Use effective interrupt affinity
net/mlx4: Replace irq_to_desc() abuse
PCI: mobiveil: Use irq_data_get_irq_chip_data()
PCI: xilinx-nwl: Use irq_data_get_irq_chip_data()
NTB/msi: Use irq_has_action()
mfd: ab8500-debugfs: Remove the racy fiddling with irq_desc
pinctrl: nomadik: Use irq_has_action()
drm/i915/pmu: Replace open coded kstat_irqs() copy
drm/i915/lpe_audio: Remove pointless irq_to_desc() usage
s390/irq: Use irq_desc_kstat_cpu() in show_msi_interrupt()
parisc/irq: Use irq_desc_kstat_cpu() in show_interrupts()
...
A smaller set of patches, nothing stands out as being particularly major
this cycle:
- Driver bug fixes and updates: bnxt_re, cxgb4, rxe, hns, i40iw, cxgb4,
mlx4 and mlx5
- Bug fixes and polishing for the new rts ULP
- Cleanup of uverbs checking for allowed driver operations
- Use sysfs_emit all over the place
- Lots of bug fixes and clarity improvements for hns
- hip09 support for hns
- NDR and 50/100Gb signaling rates
- Remove dma_virt_ops and go back to using the IB DMA wrappers
- mlx5 optimizations for contiguous DMA regions
-----BEGIN PGP SIGNATURE-----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=9t8b
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"A smaller set of patches, nothing stands out as being particularly
major this cycle. The biggest item would be the new HIP09 HW support
from HNS, otherwise it was pretty quiet for new work here:
- Driver bug fixes and updates: bnxt_re, cxgb4, rxe, hns, i40iw,
cxgb4, mlx4 and mlx5
- Bug fixes and polishing for the new rts ULP
- Cleanup of uverbs checking for allowed driver operations
- Use sysfs_emit all over the place
- Lots of bug fixes and clarity improvements for hns
- hip09 support for hns
- NDR and 50/100Gb signaling rates
- Remove dma_virt_ops and go back to using the IB DMA wrappers
- mlx5 optimizations for contiguous DMA regions"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (147 commits)
RDMA/cma: Don't overwrite sgid_attr after device is released
RDMA/mlx5: Fix MR cache memory leak
RDMA/rxe: Use acquire/release for memory ordering
RDMA/hns: Simplify AEQE process for different types of queue
RDMA/hns: Fix inaccurate prints
RDMA/hns: Fix incorrect symbol types
RDMA/hns: Clear redundant variable initialization
RDMA/hns: Fix coding style issues
RDMA/hns: Remove unnecessary access right set during INIT2INIT
RDMA/hns: WARN_ON if get a reserved sl from users
RDMA/hns: Avoid filling sl in high 3 bits of vlan_id
RDMA/hns: Do shift on traffic class when using RoCEv2
RDMA/hns: Normalization the judgment of some features
RDMA/hns: Limit the length of data copied between kernel and userspace
RDMA/mlx4: Remove bogus dev_base_lock usage
RDMA/uverbs: Fix incorrect variable type
RDMA/core: Do not indicate device ready when device enablement fails
RDMA/core: Clean up cq pool mechanism
RDMA/core: Update kernel documentation for ib_create_named_qp()
MAINTAINERS: SOFT-ROCE: Change Zhu Yanjun's email address
...
-----BEGIN PGP SIGNATURE-----
iQJIBAABCgAyFiEEgMe7l+5h9hnxdsnuWYigwDrT+vwFAl/ZJwsUHGJoZWxnYWFz
QGdvb2dsZS5jb20ACgkQWYigwDrT+vyGGQ//UhNBwb061zUaLWvaDy2RY67tGsED
kSNucKqrtaJtWaZDL3fmi8e15lwc4J/xWd96X0sd0udddrVto3WBjYd+CfbfhW8M
rQufCGlaj+VAZEzrwwbo1cTHXGH3g57BZbVlebCxJJ3mycIv716N4bdo0jz5vf9J
/PotN6yr5bCMWfO9320cmdaFDO2PK5o+AcRxUtkmFD854yJRZvmlxczFhj33pBB1
LLQlbi+Hr367WpK2uT2E36Z3POXwUqWOxSAs3Q4ql57/3UY1THZPIn5TmgXGqo7F
Dr3TRlScWxftssFSAmGZat7lBEaDBh9UnHPAsic0cjlUg6+PE7O+2iLZ7XrtPokL
Z8LVhdVlwLTNTfonsBSlMGFZJjh/zO9u1QtKYQjFhE5tUU3DUDaJz/pdcyjgaGQ1
RJNMlsHgdg89v7IJeyote+IfIpQs9YcyDxvXbXW8EFf8ft6KprTj1YNcsjRpgmwN
xhvTX40oDV9HwF3UUzO6xCdvmhmgD0n4m9cRR4kH+KtiImkZJ4tMh50AQnIs2wag
I1N2XRld7dqVGWLu4TYkmzxVgjJ9n8ylIRpHy9aMAR9TN+Q/ovLYxJvQkR4NYvxX
hft3YLgpF1ZKlyflvHmmKszLqdlPX5e56UQl3/VSRD3IQGe1+HzWOhrssWkPnNSc
0P8b7YpJU4WnVzQ=
=xRTv
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Decode PCIe 64 GT/s link speed (Gustavo Pimentel)
- Remove unused HAVE_PCI_SET_MWI (Heiner Kallweit)
- Reduce pci_set_cacheline_size() message to debug level (Heiner
Kallweit)
- Fix pci_slot_release() NULL pointer dereference (Jubin Zhong)
- Unify ECAM constants in native PCI Express drivers (Krzysztof
Wilczyński)
- Return u8 from pci_find_capability() and similar (Puranjay Mohan)
- Return u16 from pci_find_ext_capability() and similar (Bjorn
Helgaas)
- Fix ACPI companion lookup for device 0 on the root bus (Rafael J.
Wysocki)
Resource management:
- Keep both device and resource name for config space remaps
(Alexander Lobakin)
- Bounds-check command-line resource alignment requests (Bjorn
Helgaas)
- Fix overflow in command-line resource alignment requests (Colin Ian
King)
Driver binding:
- Avoid duplicate IDs in driver dynamic IDs list (Zhenzhong Duan)
Power management:
- Save/restore Precision Time Measurement Capability for
suspend/resume (David E. Box)
- Disable PTM during suspend to save power (David E. Box)
- Add sysfs attribute for device power state (Maximilian Luz)
- Rename pci_wakeup_bus() to pci_resume_bus() (Mika Westerberg)
- Do not generate wakeup event when runtime resuming device (Mika
Westerberg)
- Save/restore ASPM L1SS Capability for suspend/resume (Vidya Sagar)
Virtualization:
- Mark AMD Raven iGPU ATS as broken in some platforms (Alex Deucher)
- Add function 1 DMA alias quirk for Marvell 9215 SATA controller
(Bjorn Helgaas)
MSI:
- Disable MSI for Pericom PCIe-USB adapter (Andy Shevchenko)
- Improve warnings for 32-bit-limited MSI support (Vidya Sagar)
Error handling:
- Cache RCEC EA Capability offset in pci_init_capabilities() (Sean V
Kelley)
- Rename reset_link() to reset_subordinates() (Sean V Kelley)
- Write AER Capability only when we control it (Sean V Kelley)
- Clear AER status only when we control AER (Sean V Kelley)
- Bind RCEC devices to the Root Port driver (Qiuxu Zhuo)
- Recover from RCiEP AER errors (Qiuxu Zhuo)
- Recover from RCEC AER errors (Sean V Kelley)
- Add pcie_link_rcec() to associate RCiEPs (Sean V Kelley)
- Add pcie_walk_rcec() to RCEC AER handling (Sean V Kelley)
- Add pcie_walk_rcec() to RCEC PME handling (Sean V Kelley)
- Add RCEC AER error injection support (Qiuxu Zhuo)
Broadcom iProc PCIe controller driver:
- Fix out-of-bound array accesses (Bharat Gooty)
- Invalidate correct PAXB inbound windows (Roman Bacik)
- Enhance PCIe Link information display (Srinath Mannam)
Cadence PCIe controller driver:
- Make "cdns,max-outbound-regions" property optional (Kishon Vijay
Abraham I)
Intel VMD host bridge driver:
- Offset client MSI-X vectors (Jon Derrick)
- Update type of __iomem pointers (Krzysztof Wilczyński)
NVIDIA Tegra PCIe controller driver:
- Move "dbi" accesses to post common DWC initialization (Vidya Sagar)
- Read "dbi" base address to program in application logic (Vidya
Sagar)
- Fix ASPM-L1SS advertisement disable code (Vidya Sagar)
- Set DesignWare IP version (Vidya Sagar)
- Continue unconfig sequence even if parts fail (Vidya Sagar)
- Check return value of tegra_pcie_init_controller() (Vidya Sagar)
- Disable LTSSM during L2 entry (Vidya Sagar)
Qualcomm PCIe controller driver:
- Document PCIe bindings for SM8250 SoC (Manivannan Sadhasivam)
- Add SM8250 SoC support (Manivannan Sadhasivam)
- Add support for configuring BDF to SID mapping for SM8250
(Manivannan Sadhasivam)
Renesas R-Car PCIe controller driver:
- rcar: Drop unused members from struct rcar_pcie_host (Lad
Prabhakar)
- PCI: rcar-pci-host: Document r8a774e1 bindings (Lad Prabhakar)
- PCI: rcar-pci-host: Convert bindings to json-schema (Yoshihiro
Shimoda)
- PCI: rcar-pci-host: Document r8a77965 bindings (Yoshihiro Shimoda)
Samsung Exynos PCIe controller driver:
- Rework driver to support Exynos5433 PCIe PHY (Jaehoon Chung)
- Rework driver to support Exynos5433 variant (Jaehoon Chung)
- Drop samsung,exynos5440-pcie binding (Marek Szyprowski)
- Add the samsung,exynos-pcie binding (Marek Szyprowski)
- Add the samsung,exynos-pcie-phy binding (Marek Szyprowski)
Synopsys DesignWare PCIe controller driver:
- Support multiple ATU memory regions (Rob Herring)
- Move intel-gw ATU offset out of driver match data (Rob Herring)
- Move "dbi", "dbi2", and "addr_space" resource setup into common
code (Rob Herring)
- Remove intel-gw unneeded function wrappers (Rob Herring)
- Ensure all outbound ATU windows are reset (Rob Herring)
- Use the common MSI irq_chip in dra7xx (Rob Herring)
- Drop the .set_num_vectors() host op (Rob Herring)
- Move MSI interrupt setup into DWC common code (Rob Herring)
- Rework MSI initialization (Rob Herring)
- Move link handling into common code (Rob Herring)
- Move dw_pcie_msi_init() into core (Rob Herring)
- Move dw_pcie_setup_rc() to DWC common code (Rob Herring)
- Remove unnecessary wrappers around dw_pcie_host_init() (Rob
Herring)
- Drop keystone duplicated 'num-viewport'" (Rob Herring)
- Move inbound and outbound windows to common struct (Rob Herring)
- Detect number of iATU windows (Rob Herring)
- Warn if non-prefetchable memory aperture size is > 32-bit (Vidya
Sagar)
- Add support to program ATU for >4GB memory (Vidya Sagar)
- Set 32-bit DMA mask for MSI target address allocation (Vidya Sagar)
TI J721E PCIe driver:
- Fix "ti,syscon-pcie-ctrl" to take argument (Kishon Vijay Abraham I)
- Add host mode dt-bindings for TI's J7200 SoC (Kishon Vijay Abraham
I)
- Add EP mode dt-bindings for TI's J7200 SoC (Kishon Vijay Abraham I)
- Get offset within "syscon" from "ti,syscon-pcie-ctrl" phandle arg
(Kishon Vijay Abraham I)
TI Keystone PCIe controller driver:
- Enable compile-testing on !ARM (Alex Dewar)"
* tag 'pci-v5.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (100 commits)
PCI: Add function 1 DMA alias quirk for Marvell 9215 SATA controller
PCI/ACPI: Fix companion lookup for device 0 on the root bus
PCI: Keep both device and resource name for config space remaps
PCI: xgene: Removed unused ".bus_shift" initialisers from pci-xgene.c
PCI: vmd: Update type of the __iomem pointers
PCI: iproc: Convert to use the new ECAM constants
PCI: thunder-pem: Add constant for custom ".bus_shift" initialiser
PCI: Unify ECAM constants in native PCI Express drivers
PCI: Disable PTM during suspend to save power
PCI/PTM: Save/restore Precision Time Measurement Capability for suspend/resume
PCI: Mark AMD Raven iGPU ATS as broken in some platforms
PCI: j721e: Get offset within "syscon" from "ti,syscon-pcie-ctrl" phandle arg
dt-bindings: PCI: Add EP mode dt-bindings for TI's J7200 SoC
dt-bindings: PCI: Add host mode dt-bindings for TI's J7200 SoC
dt-bindings: pci: ti,j721e: Fix "ti,syscon-pcie-ctrl" to take argument
PCI: dwc: Set 32-bit DMA mask for MSI target address allocation
PCI: qcom: Add support for configuring BDF to SID mapping for SM8250
PCI: Reduce pci_set_cacheline_size() message to debug level
PCI: Remove unused HAVE_PCI_SET_MWI
PCI: qcom: Add SM8250 SoC support
...
- Use local_clock() instead of jiffies in the cpufreq statistics to
improve accuracy (Viresh Kumar).
- Fix up OPP usage in the cpufreq-dt and qcom-cpufreq-nvmem cpufreq
drivers (Viresh Kumar).
- Clean up the cpufreq core, the intel_pstate driver and the
schedutil cpufreq governor (Rafael Wysocki).
- Fix up error code paths in the sti-cpufreq and mediatek cpufreq
drivers (Yangtao Li, Qinglang Miao).
- Fix cpufreq_online() to return error codes instead of success (0)
in all cases when it fails (Wang ShaoBo).
- Add mt8167 support to the mediatek cpufreq driver and blacklist
mt8516 in the cpufreq-dt-platdev driver (Fabien Parent).
- Modify the tegra194 cpufreq driver to always return values from
the frequency table as the current frequency and clean up that
driver (Sumit Gupta, Jon Hunter).
- Modify the arm_scmi cpufreq driver to allow it to discover the
power scale present in the performance protocol and provide this
information to the Energy Model (Lukasz Luba).
- Add missing MODULE_DEVICE_TABLE to several cpufreq drivers (Pali
Rohár).
- Clean up the CPPC cpufreq driver (Ionela Voinescu).
- Fix NVMEM_IMX_OCOTP dependency in the imx cpufreq driver (Arnd
Bergmann).
- Rework the poling interval selection for the polling state in
cpuidle (Mel Gorman).
- Enable suspend-to-idle for PSCI OSI mode in the PSCI cpuidle
driver (Ulf Hansson).
- Modify the OPP framework to support empty (node-less) OPP tables
in DT for passing dependency information (Nicola Mazzucato).
- Fix potential lockdep issue in the OPP core and clean up the OPP
core (Viresh Kumar).
- Modify dev_pm_opp_put_regulators() to accept a NULL argument and
update its users accordingly (Viresh Kumar).
- Add frequency changes tracepoint to devfreq (Matthias Kaehlcke).
- Add support for governor feature flags to devfreq, make devfreq
sysfs file permissions depend on the governor and clean up the
devfreq core (Chanwoo Choi).
- Clean up the tegra20 devfreq driver and deprecate it to allow
another driver based on EMC_STAT to be used instead of it (Dmitry
Osipenko).
- Add interconnect support to the tegra30 devfreq driver, allow it
to take the interconnect and OPP information from DT and clean it
up ((Dmitry Osipenko).
- Add interconnect support to the exynos-bus devfreq driver along
with interconnect properties documentation (Sylwester Nawrocki).
- Add suport for AMD Fam17h and Fam19h processors to the RAPL power
capping driver (Victor Ding, Kim Phillips).
- Fix handling of overly long constraint names in the powercap
framework (Lukasz Luba).
- Fix the wakeup configuration handling for bridges in the ACPI
device power management core (Rafael Wysocki).
- Add support for using an abstract scale for power units in the
Energy Model (EM) and document it (Lukasz Luba).
- Add em_cpu_energy() micro-optimization to the EM (Pavankumar
Kondeti).
- Modify the generic power domains (genpd) framwework to support
suspend-to-idle (Ulf Hansson).
- Fix creation of debugfs nodes in genpd (Thierry Strudel).
- Clean up genpd (Lina Iyer).
- Clean up the core system-wide suspend code and make it print
driver flags for devices with debug enabled (Alex Shi, Patrice
Chotard, Chen Yu).
- Modify the ACPI system reboot code to make it prepare for system
power off to avoid confusing the platform firmware (Kai-Heng Feng).
- Update the pm-graph (multiple changes, mostly usability-related)
and cpupower (online and offline CPU information support) PM
utilities (Todd Brandt, Brahadambal Srinivasan).
-----BEGIN PGP SIGNATURE-----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=BVdX
-----END PGP SIGNATURE-----
Merge tag 'pm-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These update cpufreq (core and drivers), cpuidle (polling state
implementation and the PSCI driver), the OPP (operating performance
points) framework, devfreq (core and drivers), the power capping RAPL
(Running Average Power Limit) driver, the Energy Model support, the
generic power domains (genpd) framework, the ACPI device power
management, the core system-wide suspend code and power management
utilities.
Specifics:
- Use local_clock() instead of jiffies in the cpufreq statistics to
improve accuracy (Viresh Kumar).
- Fix up OPP usage in the cpufreq-dt and qcom-cpufreq-nvmem cpufreq
drivers (Viresh Kumar).
- Clean up the cpufreq core, the intel_pstate driver and the
schedutil cpufreq governor (Rafael Wysocki).
- Fix up error code paths in the sti-cpufreq and mediatek cpufreq
drivers (Yangtao Li, Qinglang Miao).
- Fix cpufreq_online() to return error codes instead of success (0)
in all cases when it fails (Wang ShaoBo).
- Add mt8167 support to the mediatek cpufreq driver and blacklist
mt8516 in the cpufreq-dt-platdev driver (Fabien Parent).
- Modify the tegra194 cpufreq driver to always return values from the
frequency table as the current frequency and clean up that driver
(Sumit Gupta, Jon Hunter).
- Modify the arm_scmi cpufreq driver to allow it to discover the
power scale present in the performance protocol and provide this
information to the Energy Model (Lukasz Luba).
- Add missing MODULE_DEVICE_TABLE to several cpufreq drivers (Pali
Rohár).
- Clean up the CPPC cpufreq driver (Ionela Voinescu).
- Fix NVMEM_IMX_OCOTP dependency in the imx cpufreq driver (Arnd
Bergmann).
- Rework the poling interval selection for the polling state in
cpuidle (Mel Gorman).
- Enable suspend-to-idle for PSCI OSI mode in the PSCI cpuidle driver
(Ulf Hansson).
- Modify the OPP framework to support empty (node-less) OPP tables in
DT for passing dependency information (Nicola Mazzucato).
- Fix potential lockdep issue in the OPP core and clean up the OPP
core (Viresh Kumar).
- Modify dev_pm_opp_put_regulators() to accept a NULL argument and
update its users accordingly (Viresh Kumar).
- Add frequency changes tracepoint to devfreq (Matthias Kaehlcke).
- Add support for governor feature flags to devfreq, make devfreq
sysfs file permissions depend on the governor and clean up the
devfreq core (Chanwoo Choi).
- Clean up the tegra20 devfreq driver and deprecate it to allow
another driver based on EMC_STAT to be used instead of it (Dmitry
Osipenko).
- Add interconnect support to the tegra30 devfreq driver, allow it to
take the interconnect and OPP information from DT and clean it up
(Dmitry Osipenko).
- Add interconnect support to the exynos-bus devfreq driver along
with interconnect properties documentation (Sylwester Nawrocki).
- Add suport for AMD Fam17h and Fam19h processors to the RAPL power
capping driver (Victor Ding, Kim Phillips).
- Fix handling of overly long constraint names in the powercap
framework (Lukasz Luba).
- Fix the wakeup configuration handling for bridges in the ACPI
device power management core (Rafael Wysocki).
- Add support for using an abstract scale for power units in the
Energy Model (EM) and document it (Lukasz Luba).
- Add em_cpu_energy() micro-optimization to the EM (Pavankumar
Kondeti).
- Modify the generic power domains (genpd) framwework to support
suspend-to-idle (Ulf Hansson).
- Fix creation of debugfs nodes in genpd (Thierry Strudel).
- Clean up genpd (Lina Iyer).
- Clean up the core system-wide suspend code and make it print driver
flags for devices with debug enabled (Alex Shi, Patrice Chotard,
Chen Yu).
- Modify the ACPI system reboot code to make it prepare for system
power off to avoid confusing the platform firmware (Kai-Heng Feng).
- Update the pm-graph (multiple changes, mostly usability-related)
and cpupower (online and offline CPU information support) PM
utilities (Todd Brandt, Brahadambal Srinivasan)"
* tag 'pm-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (86 commits)
cpufreq: Fix cpufreq_online() return value on errors
cpufreq: Fix up several kerneldoc comments
cpufreq: stats: Use local_clock() instead of jiffies
cpufreq: schedutil: Simplify sugov_update_next_freq()
cpufreq: intel_pstate: Simplify intel_cpufreq_update_pstate()
PM: domains: create debugfs nodes when adding power domains
opp: of: Allow empty opp-table with opp-shared
dt-bindings: opp: Allow empty OPP tables
media: venus: dev_pm_opp_put_*() accepts NULL argument
drm/panfrost: dev_pm_opp_put_*() accepts NULL argument
drm/lima: dev_pm_opp_put_*() accepts NULL argument
PM / devfreq: exynos: dev_pm_opp_put_*() accepts NULL argument
cpufreq: qcom-cpufreq-nvmem: dev_pm_opp_put_*() accepts NULL argument
cpufreq: dt: dev_pm_opp_put_regulators() accepts NULL argument
opp: Allow dev_pm_opp_put_*() APIs to accept NULL opp_table
opp: Don't create an OPP table from dev_pm_opp_get_opp_table()
cpufreq: dt: Don't (ab)use dev_pm_opp_get_opp_table() to create OPP table
opp: Reduce the size of critical section in _opp_kref_release()
PM / EM: Micro optimization in em_cpu_energy
cpufreq: arm_scmi: Discover the power scale in performance protocol
...
- Support multiple ATU memory regions (Rob Herring)
- Warn if non-prefetchable memory aperture is > 32-bit (Vidya Sagar)
- Allow programming ATU for >4GB memory (Vidya Sagar)
- Move ATU offset out of driver match data (Rob Herring)
- Move "dbi", "dbi2", and "addr_space" resource setup to common code (Rob
Herring)
- Remove unneeded function wrappers (Rob Herring)
- Ensure all outbound ATU windows are reset to reduce dependencies on
bootloader (Rob Herring)
- Use the default MSI irq_chip for dra7xx (Rob Herring)
- Drop the .set_num_vectors() host op (Rob Herring)
- Move MSI interrupt setup into DWC common code (Rob Herring)
- Rework and simplify DWC MSI initialization (Rob Herring)
- Move link handling to DWC common code (Rob Herring)
- Move dw_pcie_msi_init() calls to DWC common code (Rob Herring)
- Move dw_pcie_setup_rc() calls to DWC common code (Rob Herring)
- Remove unnecessary wrappers around dw_pcie_host_init() (Rob Herring)
- Revert "keystone: Drop duplicated 'num-viewport'" to prepare for
detecting number of iATU regions without help from DT (Rob Herring)
- Move inbound and outbound windows to common struct (Rob Herring)
- Detect number of DWC iATU windows from device registers (Rob Herring)
- Drop samsung,exynos5440-pcie binding (Marek Szyprowski)
- Add samsung,exynos-pcie and samsung,exynos-pcie-phy bindings for
Exynos5433 variant (Marek Szyprowski)
- Rework phy-exynos-pcie driver to support Exynos5433 PCIe PHY (Jaehoon
Chung)
- Rework pci-exynos.c to support Exynos5433 PCIe host (Jaehoon Chung)
- Move tegra "dbi" accesses to post common DWC initialization (Vidya Sagar)
- Read tegra dbi" base address in application logic (Vidya Sagar)
- Fix tegra ASPM-L1SS advertisement disable code (Vidya Sagar)
- Set Tegra194 DesignWare IP version to 0x490A (Vidya Sagar)
- Continue tegra unconfig sequence even if parts fail (Vidya Sagar)
- Check return value of tegra_pcie_init_controller() (Vidya Sagar)
- Disable tegra LTSSM during L2 entry (Vidya Sagar)
- Add SM8250 SoC PCIe DT bindings and support (Manivannan Sadhasivam)
- Add SM8250 BDF to SID mapping (Manivannan Sadhasivam)
- Set 32-bit DMA mask for DWC MSI target address allocation (Vidya Sagar)
* remotes/lorenzo/pci/dwc:
PCI: dwc: Set 32-bit DMA mask for MSI target address allocation
PCI: qcom: Add support for configuring BDF to SID mapping for SM8250
PCI: qcom: Add SM8250 SoC support
dt-bindings: pci: qcom: Document PCIe bindings for SM8250 SoC
PCI: tegra: Disable LTSSM during L2 entry
PCI: tegra: Check return value of tegra_pcie_init_controller()
PCI: tegra: Continue unconfig sequence even if parts fail
PCI: tegra: Set DesignWare IP version
PCI: tegra: Fix ASPM-L1SS advertisement disable code
PCI: tegra: Read "dbi" base address to program in application logic
PCI: tegra: Move "dbi" accesses to post common DWC initialization
PCI: dwc: exynos: Rework the driver to support Exynos5433 variant
phy: samsung: phy-exynos-pcie: rework driver to support Exynos5433 PCIe PHY
dt-bindings: phy: exynos: add the samsung,exynos-pcie-phy binding
dt-bindings: PCI: exynos: add the samsung,exynos-pcie binding
dt-bindings: PCI: exynos: drop samsung,exynos5440-pcie binding
PCI: dwc: Detect number of iATU windows
PCI: dwc: Move inbound and outbound windows to common struct
Revert "PCI: dwc/keystone: Drop duplicated 'num-viewport'"
PCI: dwc: Remove unnecessary wrappers around dw_pcie_host_init()
PCI: dwc: Move dw_pcie_setup_rc() to DWC common code
PCI: dwc: Move dw_pcie_msi_init() into core
PCI: dwc: Move link handling into common code
PCI: dwc: Rework MSI initialization
PCI: dwc: Move MSI interrupt setup into DWC common code
PCI: dwc: Drop the .set_num_vectors() host op
PCI: dwc/dra7xx: Use the common MSI irq_chip
PCI: dwc: Ensure all outbound ATU windows are reset
PCI: dwc/intel-gw: Remove some unneeded function wrappers
PCI: dwc: Move "dbi", "dbi2", and "addr_space" resource setup into common code
PCI: dwc/intel-gw: Move ATU offset out of driver match data
PCI: dwc: Add support to program ATU for >4GB memory
PCI: of: Warn if non-prefetchable memory aperture size is > 32-bit
PCI: dwc: Support multiple ATU memory regions
- Make "cdns,max-outbound-regions" optional (Kishon Vijay Abraham I)
- Fix "ti,syscon-pcie-ctrl" DT property to take argument (Kishon Vijay
Abraham I)
- Add TI J7200 host and endpoint mode DT bindings (Kishon Vijay Abraham I)
* remotes/lorenzo/pci/cadence:
PCI: j721e: Get offset within "syscon" from "ti,syscon-pcie-ctrl" phandle arg
dt-bindings: PCI: Add EP mode dt-bindings for TI's J7200 SoC
dt-bindings: PCI: Add host mode dt-bindings for TI's J7200 SoC
dt-bindings: pci: ti,j721e: Fix "ti,syscon-pcie-ctrl" to take argument
PCI: cadence: Do not error if "cdns,max-outbound-regions" is not found
dt-bindings: PCI: Make "cdns,max-outbound-regions" optional property
- Update comment about delay before link training (Pali Rohár)
* remotes/lorenzo/pci/aardvark:
PCI: aardvark: Update comment about disabling link training
- Mark AMD Raven iGPU ATS as broken in some Emerson platforms to avoid
issues (Alex Deucher)
- Add function 1 DMA alias quirk for Marvell 9215 SATA controller (Bjorn
Helgaas)
* pci/virtualization:
PCI: Add function 1 DMA alias quirk for Marvell 9215 SATA controller
PCI: Mark AMD Raven iGPU ATS as broken in some platforms
- Save/restore Precision Time Measurement Capability for suspend/resume
(David E. Box)
- Disable PTM during suspend to save power (David E. Box)
* pci/ptm:
PCI: Disable PTM during suspend to save power
PCI/PTM: Save/restore Precision Time Measurement Capability for suspend/resume
- Add sysfs attribute for device power state (Maximilian Luz)
- Rename pci_wakeup_bus() to pci_resume_bus() (Mika Westerberg)
- Do not generate wakeup event when runtime resuming bus (Mika Westerberg)
* pci/pm:
PCI/PM: Do not generate wakeup event when runtime resuming device
PCI/PM: Rename pci_wakeup_bus() to pci_resume_bus()
PCI: Add sysfs attribute for device power state
- Disable MSI for broken Pericom PCIe-USB adapter (Andy Shevchenko)
- Move MSI/MSI-X init to msi.c (Bjorn Helgaas)
- Move MSI/MSI-X flags updaters to msi.c (Bjorn Helgaas)
- Warn if we assign 64-bit MSI address to device that only supports 32-bit
MSI (Vidya Sagar)
* pci/msi:
PCI/MSI: Set device flag indicating only 32-bit MSI support
PCI/MSI: Move MSI/MSI-X flags updaters to msi.c
PCI/MSI: Move MSI/MSI-X init to msi.c
PCI: Use predefined Pericom Vendor ID
PCI: Disable MSI for Pericom PCIe-USB adapter
- Stop writing AER Capability when we don't own it (Sean V Kelley)
- Bind RCEC devices to the Port driver (Qiuxu Zhuo)
- Cache the RCEC RA Capability offset (Sean V Kelley)
- Add pci_walk_bridge() (Sean V Kelley)
- Clear AER status only when we control AER (Sean V Kelley)
- Recover from RCEC AER errors (Sean V Kelley)
- Add pcie_link_rcec() to associate RCiEPs with RCECs (Sean V Kelley)
- Recover from RCiEP AER errors (Sean V Kelley)
- Add pcie_walk_rcec() for RCEC AER handling (Sean V Kelley)
- Add pcie_walk_rcec() for RCEC PME handling (Sean V Kelley)
- Add RCEC AER error injection support (Qiuxu Zhuo)
* pci/err:
PCI/AER: Add RCEC AER error injection support
PCI/PME: Add pcie_walk_rcec() to RCEC PME handling
PCI/AER: Add pcie_walk_rcec() to RCEC AER handling
PCI/ERR: Recover from RCiEP AER errors
PCI/ERR: Add pcie_link_rcec() to associate RCiEPs
PCI/ERR: Recover from RCEC AER errors
PCI/ERR: Clear AER status only when we control AER
PCI/ERR: Add pci_walk_bridge() to pcie_do_recovery()
PCI/ERR: Avoid negated conditional for clarity
PCI/ERR: Use "bridge" for clarity in pcie_do_recovery()
PCI/ERR: Simplify by computing pci_pcie_type() once
PCI/ERR: Simplify by using pci_upstream_bridge()
PCI/ERR: Rename reset_link() to reset_subordinates()
PCI/ERR: Cache RCEC EA Capability offset in pci_init_capabilities()
PCI/ERR: Bind RCEC devices to the Root Port driver
PCI/AER: Write AER Capability only when we control it
- Decode PCIe 64 GT/s link speed (Gustavo Pimentel)
- De-duplicate Device IDs in the driver dynamic IDs list (Zhenzhong Duan)
- Return u8 from pci_find_capability() and similar (Puranjay Mohan)
- Return u16 from pci_find_ext_capability() and similar (Bjorn Helgaas)
- Include both device and resource name in config space resources
(Alexander Lobakin)
- Fix ACPI companion lookup for device 0 on the root bus (Rafael J.
Wysocki)
* pci/enumeration:
PCI/ACPI: Fix companion lookup for device 0 on the root bus
PCI: Keep both device and resource name for config space remaps
PCI: Return u16 from pci_find_ext_capability() and similar
PCI: Return u8 from pci_find_capability() and similar
PCI: Avoid duplicate IDs in driver dynamic IDs list
PCI: Move pci_match_device() ahead of new_id_store()
PCI: Decode PCIe 64 GT/s link speed
Going through a full irq descriptor lookup instead of just using the proper
helper function which provides direct access is suboptimal.
In fact it _is_ wrong because the chip callback needs to get the chip data
which is relevant for the chip while using the irq descriptor variant
returns the irq chip data of the top level chip of a hierarchy. It does not
matter in this case because the chip is the top level chip, but that
doesn't make it more correct.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20201210194044.473308721@linutronix.de
Going through a full irq descriptor lookup instead of just using the proper
helper function which provides direct access is suboptimal.
In fact it _is_ wrong because the chip callback needs to get the chip data
which is relevant for the chip while using the irq descriptor variant
returns the irq chip data of the top level chip of a hierarchy. It does not
matter in this case because the chip is the top level chip, but that
doesn't make it more correct.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20201210194044.364211860@linutronix.de
- Simplification and distangling of the MSI related functionality
- Let IO/APIC construct the RTE entries from an MSI message instead of
having IO/APIC specific code in the interrupt remapping drivers
- Make the retrieval of the parent interrupt domain (vector or remap
unit) less hardcoded and use the relevant irqdomain callbacks for
selection.
- Allow the handling of more than 255 CPUs without a virtualized IOMMU
when the hypervisor supports it. This has made been possible by the
above modifications and also simplifies the existing workaround in the
HyperV specific virtual IOMMU.
- Cleanup of the historical timer_works() irq flags related
inconsistencies.
-----BEGIN PGP SIGNATURE-----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=8Gfs
-----END PGP SIGNATURE-----
Merge tag 'x86-apic-2020-12-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 apic updates from Thomas Gleixner:
"Yet another large set of x86 interrupt management updates:
- Simplification and distangling of the MSI related functionality
- Let IO/APIC construct the RTE entries from an MSI message instead
of having IO/APIC specific code in the interrupt remapping drivers
- Make the retrieval of the parent interrupt domain (vector or remap
unit) less hardcoded and use the relevant irqdomain callbacks for
selection.
- Allow the handling of more than 255 CPUs without a virtualized
IOMMU when the hypervisor supports it. This has made been possible
by the above modifications and also simplifies the existing
workaround in the HyperV specific virtual IOMMU.
- Cleanup of the historical timer_works() irq flags related
inconsistencies"
* tag 'x86-apic-2020-12-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (42 commits)
x86/ioapic: Cleanup the timer_works() irqflags mess
iommu/hyper-v: Remove I/O-APIC ID check from hyperv_irq_remapping_select()
iommu/amd: Fix IOMMU interrupt generation in X2APIC mode
iommu/amd: Don't register interrupt remapping irqdomain when IR is disabled
iommu/amd: Fix union of bitfields in intcapxt support
x86/ioapic: Correct the PCI/ISA trigger type selection
x86/ioapic: Use I/O-APIC ID for finding irqdomain, not index
x86/hyperv: Enable 15-bit APIC ID if the hypervisor supports it
x86/kvm: Enable 15-bit extension when KVM_FEATURE_MSI_EXT_DEST_ID detected
iommu/hyper-v: Disable IRQ pseudo-remapping if 15 bit APIC IDs are available
x86/apic: Support 15 bits of APIC ID in MSI where available
x86/ioapic: Handle Extended Destination ID field in RTE
iommu/vt-d: Simplify intel_irq_remapping_select()
x86: Kill all traces of irq_remapping_get_irq_domain()
x86/ioapic: Use irq_find_matching_fwspec() to find remapping irqdomain
x86/hpet: Use irq_find_matching_fwspec() to find remapping irqdomain
iommu/hyper-v: Implement select() method on remapping irqdomain
iommu/vt-d: Implement select() method on remapping irqdomain
iommu/amd: Implement select() method on remapping irqdomain
x86/apic: Add select() method on vector irqdomain
...
In some cases acpi_pci_find_companion() returns an incorrect device object
as the ACPI companion for device 0 on the root bus (bus 0).
On the affected systems that device is the PCI interface to the host bridge
and the "ACPI companion" returned for it corresponds to a non-PCI device
located in the SoC (e.g. a sensor on an I2C bus). As a result of this, the
ACPI device object "attached" to PCI device 00:00.0 cannot be used for
enumerating the device that is really represented by it which (of course)
is problematic.
Address that issue by preventing acpi_pci_find_companion() from returning a
device object with a valid _HID (which by the spec should not be present
uder ACPI device objects corresponding to PCI devices) for PCI device
00:00.0.
[bhelgaas: use pci_is_root_bus()]
Link: https://lore.kernel.org/linux-acpi/1409ba0c-1580-dc09-e6fe-a0c9bcda6462@gmail.com/
Link: https://lore.kernel.org/r/4673285.9aE2nYKHPr@kreacher
Reported-by: Daniel Scally <djrscally@gmail.com>
Tested-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Daniel Scally <djrscally@gmail.com>
Follow the rule taken in commit 35bd8c07db ("devres: keep both device
name and resource name in pretty name") and keep both device and resource
names while requesting memory regions for PCI config space to prettify e.g.
/proc/iomem output:
Before (DWC Host Controller):
18b00000-18b01fff : dbi
18b10000-18b11fff : config
18b20000-18b21fff : dbi
18b30000-18b31fff : config
After:
18b00000-18b01fff : 18b00000.pci dbi
18b10000-18b11fff : 18b00000.pci config
18b20000-18b21fff : 18b20000.pci dbi
18b30000-18b31fff : 18b20000.pci config
Link: https://lore.kernel.org/r/WbKfdybjZ6xNIUjcC5oC8NcuLqrJfkxQAlnO80ag@cp3-web-020.plabs.ch
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Removed unused ".bus_shift" initialisers from pci-xgene.c as
xgene_pcie_map_bus() did not use these.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20201129230743.3006978-6-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use "void __iomem" instead "char __iomem" pointer type when working with
the accessor functions (with names like readb() or writel(), etc.) to
better match a given accessor function signature where commonly the address
pointing to an I/O memory region would be a "void __iomem" pointer.
Related: https://lwn.net/Articles/102232/
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20201129230743.3006978-5-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Change interface of the function iproc_pcie_map_ep_cfg_reg() so that use
of PCI_SLOT() and PCI_FUNC() macros and most of the local ECAM-specific
constants can be dropped, and the new PCIE_ECAM_OFFSET() macro can be
used instead. Use the ALIGN_DOWN() macro to ensure that PCI Express
ECAM offset is always 32 bit aligned.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20201129230743.3006978-4-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a custom constant for the ".bus_shift" initialiser to capture a
non-standard platform-specific ECAM bus shift value.
Standard values otherwise defined in the PCI Express Specification are
available in the include/linux/pci-ecam.h.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20201129230743.3006978-3-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add ECAM-related constants to provide a set of standard constants
defining memory address shift values to the byte-level address that can
be used to access the PCI Express Configuration Space, and then move
native PCI Express controller drivers to use the newly introduced
definitions retiring driver-specific ones.
Refactor pci_ecam_map_bus() function to use newly added constants so
that limits to the bus, device function and offset (now limited to 4K as
per the specification) are in place to prevent the defective or
malicious caller from supplying incorrect configuration offset and thus
targeting the wrong device when accessing extended configuration space.
This refactor also allows for the ".bus_shift" initialisers to be
dropped when the user is not using a custom value as a default value
will be used as per the PCI Express Specification.
Thanks to Qian Cai <qcai@redhat.com>, Michael Walle <michael@walle.cc>,
and Vladimir Oltean <olteanv@gmail.com> for reporting a pci_ecam_create()
issue with .bus_shift and to Vladimir for proposing the fix.
[bhelgaas: incorporate Vladimir's fix, update commit log]
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20201129230743.3006978-2-kw@linux.com
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
There are systems (for example, Intel based mobile platforms since Coffee
Lake) where the power drawn while suspended can be significantly reduced by
disabling Precision Time Measurement (PTM) on PCIe root ports as this
allows the port to enter a lower-power PM state and the SoC to reach a
lower-power idle state. To save this power, disable the PTM feature on root
ports during pci_prepare_to_sleep() and pci_finish_runtime_suspend(). The
feature will be returned to its previous state during restore and error
recovery.
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=209361
Link: https://lore.kernel.org/r/20201207223951.19667-2-david.e.box@linux.intel.com
Reported-by: Len Brown <len.brown@intel.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI subsystem does not currently save and restore the configuration
space for the Precision Time Measurement (PTM) Extended Capability leading
to the possibility of the feature returning disabled on S3 resume. This
has been observed on Intel Coffee Lake desktops. Add save/restore of the
PTM control register. This saves the PTM Enable, Root Select, and Effective
Granularity bits.
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20201207223951.19667-1-david.e.box@linux.intel.com
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Get "syscon" pcie_ctrl offset from the argument of "ti,syscon-pcie-ctrl"
phandle. Previously a subnode to "syscon" node was added which has the
exact memory mapped address of pcie_ctrl but now the offset of pcie_ctrl
within "syscon" is now being passed as argument to "ti,syscon-pcie-ctrl"
phandle.
If the offset is not provided in "ti,syscon-pcie-ctrl", the
full memory mapped address of pcie_ctrl is used in order to maintain old
DT compatibility.
This change is as discussed in [1]
[1] -> http://lore.kernel.org/r/CAL_JsqKiUcO76bo1GoepWM1TusJWoty_BRy2hFSgtEVMqtrvvQ@mail.gmail.com
Link: https://lore.kernel.org/r/20201210124917.24185-5-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Set DMA mask to 32-bit while allocating the MSI target address so that
the address is usable for both 32-bit and 64-bit MSI capable devices.
Throw a warning if it fails to set the mask to 32-bit to alert that
devices that are only 32-bit MSI capable may not work properly.
Link: https://lore.kernel.org/r/20201117165312.25847-1-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
For SM8250, we need to write the BDF to SID mapping in PCIe controller
register space for proper working. This is accomplished by extracting
the BDF and SID values from "iommu-map" property in DT and writing those
in the register address calculated from the hash value of BDF. In case
of collisions, the index of the next entry will also be written.
For the sake of it, let's introduce a "config_sid" callback and do it
conditionally for SM8250.
Link: https://lore.kernel.org/r/20201208121402.178011-4-mani@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Drivers like ehci_hcd and xhci_hcd use pci_set_mwi() and emit an annnoying
message like the following that results in user questions whether something
is broken:
xhci_hcd 0000:00:15.0: cache line size of 64 is not supported
Root cause of the message is that on several chips the Cache Line Size
register is hard-wired to 0.
Change this message to debug level; an interested caller can still inform
the user (if deemed helpful) based on the return code.
Link: https://lore.kernel.org/r/be1ed3a2-98b9-ee1d-20b8-477f3d93961d@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCIe IP (rev 1.9.0) on SM8250 SoC is similar to the one used on
SDM845. Hence the support is added reusing the members of ops_2_7_0.
The key difference between ops_2_7_0 and ops_1_9_0 is the config_sid
callback, which will be added in successive commit.
Link: https://lore.kernel.org/r/20201208121402.178011-3-mani@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
PCIe cards like Marvell SATA controller and some of the Samsung NVMe
drives don't support taking the link to L2 state. When the link doesn't
go to L2 state, Tegra194 requires the LTSSM to be disabled to allow PHY
to start the next link up process cleanly during suspend/resume sequence.
Failing to disable LTSSM results in the PCIe link not coming up in the
next resume cycle.
Link: https://lore.kernel.org/r/20201203133451.17716-6-vidyas@nvidia.com
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
The return value of tegra_pcie_init_controller() must be checked before
PCIe link up check and registering debugfs entries subsequently as it
doesn't make sense to do these when the controller initialization itself
has failed.
Link: https://lore.kernel.org/r/20201203133451.17716-5-vidyas@nvidia.com
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Currently the driver checks for error value of different APIs during the
uninitialization sequence. It just returns from there if there is any error
observed for one of those calls. Comparatively it is better to continue the
uninitialization sequence irrespective of whether some of them are
returning error. That way, it is more closer to complete uninitialization.
Link: https://lore.kernel.org/r/20201203133451.17716-4-vidyas@nvidia.com
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Set the DesignWare IP version for Tegra194 to 0x490A. This would be used
by the DesigWare sub-system to do any version specific configuration
(Ex:- TD bit programming for ECRC).
Link: https://lore.kernel.org/r/20201203133451.17716-3-vidyas@nvidia.com
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
If the absence of CLKREQ# signal is indicated by the absence of
"supports-clkreq" in the device-tree node, current driver is disabling
the advertisement of ASPM-L1 Sub-States *before* the ASPM-L1 Sub-States
offset is correctly initialized. Since default value of the ASPM-L1SS
offset is zero, this is causing the Vendor-ID wrongly programmed to 0x10d2
instead of Nvidia's 0x10de thereby the quirks applicable for Tegra194 are
not being applied. This patch fixes this issue by refactoring the
code that disables the ASPM-L1SS advertisement.
Link: https://lore.kernel.org/r/20201203133451.17716-2-vidyas@nvidia.com
Fixes: 56e15a238d ("PCI: tegra: Add Tegra194 PCIe support")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
According to PCI Express Base Specifications (rev 4.0, 6.6.1
"Conventional reset"), after fundamental reset a 100ms delay is needed
prior to enabling link training.
Update comment in code to reflect this requirement.
Link: https://lore.kernel.org/r/20201202184659.3795-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The idea behind acpi_pm_set_bridge_wakeup() was to allow bridges to
be reference counted for wakeup enabling, because they may be enabled
to signal wakeup on behalf of their subordinate devices and that
may happen for multiple times in a row, whereas for the other devices
it only makes sense to enable wakeup signaling once.
However, this becomes problematic if the bridge itself is suspended,
because it is treated as a "regular" device in that case and the
reference counting doesn't work.
For instance, suppose that there are two devices below a bridge and
they both can signal wakeup. Every time one of them is suspended,
wakeup signaling is enabled for the bridge, so when they both have
been suspended, the bridge's wakeup reference counter value is 2.
Say that the bridge is suspended subsequently and acpi_pci_wakeup()
is called for it. Because the bridge can signal wakeup, that
function will invoke acpi_pm_set_device_wakeup() to configure it
and __acpi_pm_set_device_wakeup() will be called with the last
argument equal to 1. This causes __acpi_device_wakeup_enable()
invoked by it to omit the reference counting, because the reference
counter of the target device (the bridge) is 2 at that time.
Now say that the bridge resumes and one of the device below it
resumes too, so the bridge's reference counter becomes 0 and
wakeup signaling is disabled for it, but there is still the other
suspended device which may need the bridge to signal wakeup on its
behalf and that is not going to work.
To address this scenario, use wakeup enable reference counting for
all devices, not just for bridges, so drop the last argument from
__acpi_device_wakeup_enable() and __acpi_pm_set_device_wakeup(),
which causes acpi_pm_set_device_wakeup() and
acpi_pm_set_bridge_wakeup() to become identical, so drop the latter
and use the former instead of it everywhere.
Fixes: 1ba51a7c14 ("ACPI / PCI / PM: Rework acpi_pci_propagate_wakeup()")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: 4.14+ <stable@vger.kernel.org> # 4.14+
Root Complex Event Collectors (RCEC) appear as peers to Root Ports and may
also have the AER capability.
Add RCEC support to the AER error injection driver.
Co-developed-by: Sean V Kelley <sean.v.kelley@intel.com>
Link: https://lore.kernel.org/r/20201121001036.8560-16-sean.v.kelley@intel.com
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # non-native/no RCEC
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Sean V Kelley <sean.v.kelley@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Russell King