SKB lists have their own lock. So this lock is not needed.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes an issue with rx processing function where we were
decrementing rx_pending count twice.
Patch also queues correct main_work item when rx_pending count reaches
low watermark.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A soft lockup was observed on ARM multicore platform while UDP
RX iperf was running on station.
Reason for this is delay_main_task was not taken into consideration while
jumping to process_start. Now if delay_main_task is true, we would exit
mwifiex_main_process instead of going to process_start again.
This ensure other process is scheduled on this CPU and soft lockup is avoided.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kevin Gan <ganhy@marvell.com>
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch takes care of missing error paths in firmware dump.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check for scan channel gap only when user_scan_in is not NULL.
user_scan_in is NULL for internal scans and if we check scan channel gap
at this place, it may result into crash.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville says:
====================
pull request: wireless-next 2014-09-22
Please pull this batch of updates intended for the 3.18 stream...
For the mac80211 bits, Johannes says:
"This time, I have some rate minstrel improvements, support for a very
small feature from CCX that Steinar reverse-engineered, dynamic ACK
timeout support, a number of changes for TDLS, early support for radio
resource measurement and many fixes. Also, I'm changing a number of
places to clear key memory when it's freed and Intel claims copyright
for code they developed."
For the bluetooth bits, Johan says:
"Here are some more patches intended for 3.18. Most of them are cleanups
or fixes for SMP. The only exception is a fix for BR/EDR L2CAP fixed
channels which should now work better together with the L2CAP
information request procedure."
For the iwlwifi bits, Emmanuel says:
"I fix here dvm which was broken by my last pull request. Arik
continues to work on TDLS and Luca solved a few issues in CT-Kill. Eyal
keeps digging into rate scaling code, more to come soon. Besides this,
nothing really special here."
Beyond that, there are the usual big batches of updates to ath9k, b43,
mwifiex, and wil6210 as well as a handful of other bits here and there.
Also, rtlwifi gets some btcoexist attention from Larry.
Please let me know if there are problems!
====================
Had to adjust the wil6210 code to comply with Joe Perches's recent
change in net-next to make the netdev_*() routines return void instead
of 'int'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds RX work queue support to mwifiex.
Packets received are queued to internal queue which are then
processed by scheduling a work item for RX process.
RX work is enabled only on SMP systems.
Reviewed-by: James Cameron <quozl@laptop.org>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have a logic in driver to delay or abort low priority scan
to serve Tx traffic effectively. With scan channel
gap support added, firmware now allows driver to send Tx data while
scan operation is in progress. Hence low priority scan handling
in driver is not required now. This patch removes related code.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This variable is never used, get rid of it.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With channel scan gap, FW comes back to connected channel after each
single channel scan. So we can safely transfer data to FW during scan.
FW would send this data once on connected channel.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With scan channel gap in place, FW comes back to connected channel
after each scan; so we dont need to restrict FW to scan
single channel while connected.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With scan channel gap when any station/AP is active, FW comes back
to connected channel for any pending data transfter after scanning each
channel.
We set scan channel gap TLV to FW in scan command when any of the
interface is active. This enables scan channel gap in FW.
Also when scan channel gap is enabled, we would scan maximum channels
allowed by FW.
Scan channel gap is supported only on FW with V15 FW API.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It was observed that station would sent probe request even when
scan type has been set as passive during iw scan.
This was happening because driver sets passive scan type only
when channel has IEEE80211_CHAN_NO_IR flag set.
Along with this, add condition to check if no ssids are specified in
scan request so as to mark such scan request passive.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'mp_data_port_mask' and 'mp_end_port' gives correct information
even for the chipsets supporting SDIO new mode (32 ports).
We will get rid of this chip specific handling.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When aggregation port limit is reached, we stop aggregation and
the data is sent to firmware. It is observed that one less packet
than the port limit is aggregated in this case. ex. 15 instead of
16.
The reason is we have redundant port limit checks before current
packet is added to aggregation buffer.
The issue is fixed by removing these checks. We already have
necessary check in precopy current buffer handling.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When assocaiting to an AP , mwifiex set supported data rates
based on target AP's capability. For 5G AP(11a mode), a/n/ac mode
would possibly be set.
However, for some chips which dont support 11AC mode current config_bands
will be used instead.
For example, if we join an IBSS in 11b mode ,adapter->config_bands
will be set to 1(11b mode). Then we leave IBSS ,and try to connect
5G a/n mode AP. At this time , only 11b mode data rates will be
supported in assoc request , which result in assoc failure with
reason code 18: Association denied due to requesting station not
supporting all rates.
This patch fix such a cornel case, by adding additional check for
current chip's 11ac capability.
Reported-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for writing CPU event interrupt done back
to device.
Patch also increases interrupt buffer ring size from 4 to 8.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was an issue with internal scan during association wherein
we would complete internal scan on first scan command response.
This would cause association failure if AP is not found in first scan
response e.g. APs from A band.
This patch fixes this issue by completing internal scan only when all
scan commands from scan pending queue and command pending queue are
sent to FW and response to last scan command is received.
Tested-by: Xinmin Hu <huxm@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If rx_len received in interface header from FW is more than
RX buffer size, skb_put for such length results into skb_panic.
Avoid this by not processing such packets. We just print a warning
for such packets and free skb.
Reviewed-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marc Yang <yangyang@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Size of RSN IE buffer in driver is 254 while maximum size of received buffer
to be copied to RSN IE buffer can be 255. Add boundary check to copy maximum
of 254 bytes into RSN IE buffer.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If we dont set FW API info here, for older FW releases where FW API
is not available in GET_HW_SPEC, API version would remain 0.
This may cause issues with 11ac if older FW is used with newer driver.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the much more common pr_warn instead of pr_warning.
Other miscellanea:
o Typo fixes submiting/submitting
o Coalesce formats
o Realign arguments
o Add missing terminating '\n' to formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
performance improvements, and various patches all over,
rather than listing them one might as well look into the
git log instead.
-----BEGIN PGP SIGNATURE-----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=Qth6
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-john-2014-08-29' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg <johannes@sipsolutions.net> says:
"Not that much content this time. Some RCU cleanups, crypto
performance improvements, and various patches all over,
rather than listing them one might as well look into the
git log instead."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
drivers/net/wireless/ath/wil6210/wmi.c
Newer firmware returns API revision in GET_HW_SPEC command
response. We will make use of it instead of parsing this
information from FW release number.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We will remove 'fw' prefix from these variable and macro
names and make them generic.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While updating 'left_len' in each iteration, we should subtract
last TLV length not the accumulated length of TLVs parsed till
now.
This bug in parsing logic is exposed by newer firmware which adds
two TLVs in GET_HW_SPEC command response. Earlier firmwares used to
add only one TLV.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When using the cfg80211_inform_bss[_width]() functions drivers
cannot currently indicate whether the data was received in a
beacon or probe response. Fix that by passing a new enum that
indicates such (or unknown).
For good measure, use it in ath6kl.
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com> [ath6kl]
Acked-by: Arend van Spriel <arend@broadcom.com> [brcmfmac]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the cfg80211_rx_mgmt(), parameter @gfp was used for the memory allocation.
But, memory get allocated under spin_lock_bh(), this implies atomic context.
So, one can't use GFP_KERNEL, only variants with no __GFP_WAIT. Actually, in all
occurrences GFP_ATOMIC is used (wil6210 use GFP_KERNEL by mistake),
and it should be this way or warning triggered in the memory allocation code.
Remove @gfp parameter as no actual choice exist, and use hard coded
GFP_ATOMIC for memory allocation.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The prefix suggests the number should be printed in hex, so use
the %x specifier to do that.
Found by using regex suggested by Joe Perches.
Signed-off-by: Hans Wennborg <hans@hanshq.net>
Acked-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
John W. Linville says:
====================
pull request: wireless-next 2014-07-25
Please pull this batch of updates intended for the 3.17 stream!
For the mac80211 bits, Johannes says:
"We have a lot of TDLS patches, among them a fix that should make hwsim
tests happy again. The rest, this time, is mostly small fixes."
For the Bluetooth bits, Gustavo says:
"Some more patches for 3.17. The most important change here is the move of
the 6lowpan code to net/6lowpan. It has been agreed with Davem that this
change will go through the bluetooth tree. The rest are mostly clean up and
fixes."
and,
"Here follows some more patches for 3.17. These are mostly fixes to what
we've sent to you before for next merge window."
For the iwlwifi bits, Emmanuel says:
"I have the usual amount of BT Coex stuff. Arik continues to work
on TDLS and Ariej contributes a few things for HS2.0. I added a few
more things to the firmware debugging infrastructure. Eran fixes a
small bug - pretty normal content."
And for the Atheros bits, Kalle says:
"For ath6kl me and Jessica added support for ar6004 hw3.0, our latest
version of ar6004.
For ath10k Janusz added a printout so that it's easier to check what
ath10k kconfig options are enabled. He also added a debugfs file to
configure maximum amsdu and ampdu values. Also we had few fixes as
usual."
On top of that is the usual large batch of various driver updates --
brcmfmac, mwifiex, the TI drivers, and wil6210 all get some action.
Rafał has also been very busy with b43 and related updates.
Also, I pulled the wireless tree into this in order to resolve a
merge conflict...
P.S. The change to fs/compat_ioctl.c reflects a name change in a
Bluetooth header file...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
mmc_rescan will scan for non-removable cards only once, hence the card
will not be rediscovered.
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't need wall-clock time here, and in most configurations
that care, there are already timestamps in the kernel using
CONFIG_PRINTK_TIME=y.
Reported-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In managed mode if the driver is getting a re-associate command
from cfg80211, driver deauthenticates with the AP internally and
sends a disconnected event to cfg80211 before completion of its
association process. The disconnected event then modifies the
SSID length as wdev->ssid_len = 0. So, upon receiving the connect
result event from driver, cfg80211 is unable to get that BSS from
the device's BSS list and generates the following WARN_ON message.
WARNING: CPU: 0 PID: 857 at net/wireless/sme.c:658
__cfg80211_connect_result+0x3a6/0x3e0 [cfg80211]()
Avoid re-association while the device is already associated to a
network. Also remove the internal deauthentication from the
association path.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This local variable is not used anywhere in function.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The unwanted frame types are already handled in 'default' case
of the switch/case below.
The str_ptr is allocated but it can be leaked if the length check
fails in the REQUEST/RESP cases. Fix it by allocating sta_ptr
after the length checks.
Reported-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes this typo.
Reported-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sta_ptr is used only in an 'if' branch in this function.
Move it to the smaller scope where it is used.
Reported-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The unit of this timeout is in seconds.
Reported-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'else if' branch never gets the chance as its condition
matches 'if' branch's.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes pending internal scan commands are delayed to give
preference to Tx traffic. 'scan_processing' flag has been
checked at the beginning of delay timer routine to know if in the
meantime scan operation has been cancelled.
There is a corner case where pending scan commands are emptied
after scan_processing flag check is passed. In this case
wrong pointer returned by list_first_entry() is passed to
list_del() which causes system hang.
This patch fixes the issue by adding list_empty() check.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in which rx_reorder_tbl_ptr is accessed
without holding spinlock at few places.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are few places at the begining of Tx/Rx paths where
tx_info/rx_info is not correctly initialized. This patch
takes care of it.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Why is converting time formats so desired if there are proper
interfaces for this?
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bing Zhao <bzhao@marvell.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit a82fc3b4a2bceb7c6587249cb690342eb5065979.
Thomas corrected me on that I misunderstood Johannes' comment
for net_timedelta() and the ktime_get_real() usage inside
__net_timestamp().
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sleep Confirm command is sent separately while other commands
are handled through cmd_pending_q. Print sleep_confirm cmd and
its response as well as power save events so that we have a
clearer picture of power save handshake in driver log.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates mwifiex Copyright to 2014.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some SDIO controllers do not support MMC_PM_KEEP_POWER properly.
To test host sleep feature without putting the system into sleep
we need to simulate host sleep configuration & handshake between
driver and firmware using customized parameters.
This patch adds hscfg debugfs item, with which user could change
host sleep parameters for debugging.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware dump feature is added for SDIO based chipsets
which can be used with the help of ethtool commands.
1) Trigger firmware dump operation:
ethtool --set-dump mlan0 0xff
When the operation is completed, udev event will be sent to
trigger external application.
2) Following udev rule can be used to get the data from ethtool:
DRIVER=="mwifiex_sdio", ACTION=="change", RUN+="/sbin/mwifiex_sdio_fw_dump.sh"
mwifiex_sdio_fw_dump.sh: #!/bin/bash
ethtool --set-dump mlan0 0
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/ITCM.log
ethtool --set-dump mlan0 1
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/DTCM.log
ethtool --set-dump mlan0 2
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/SQRAM.log
ethtool --set-dump mlan0 3
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/APU.log
ethtool --set-dump mlan0 4
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/CIU.log
ethtool --set-dump mlan0 5
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/ICU.log
ethtool --set-dump mlan0 6
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/MAC.log
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As we can derive host pointer from adapter, maintaining
a global variable doesn't make sense.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Existing dedicated card_reset work queue is replaced with the
interface specific workqueue pointer provided by mwifiex module.
Also new work flag is added for card reset task.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware dump feature is added for PCIe based chipsets which can
be used with the help of ethtool commands.
1) Trigger firmware dump operation:
ethtool --set-dump mlan0 0xff
When the operation is completed, udev event will be sent to
trigger external application.
2) Following udev rule can be used to get the data from ethtool:
DRIVER=="mwifiex_pcie", ACTION=="change", RUN+="/sbin/mwifiex_pcie_fw_dump.sh"
mwifiex_pcie_fw_dump.sh: #!/bin/bash
ethtool --set-dump mlan0 0
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/ITCM.log
ethtool --set-dump mlan0 1
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/DTCM.log
ethtool --set-dump mlan0 2
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/SQRAM.log
ethtool --set-dump mlan0 3
ethtool --get-dump mlan0
ethtool --get-dump mlan0 data /tmp/IRAM.log
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
https://bugzilla.kernel.org/show_bug.cgi?id=70191https://bugzilla.kernel.org/show_bug.cgi?id=77581
It is observed that sometimes Tx packet is downloaded without
adding driver's txpd header. This results in firmware parsing
garbage data as packet length. Sometimes firmware is unable
to read the packet if length comes out as invalid. This stops
further traffic and timeout occurs.
The root cause is uninitialized fields in tx_info(skb->cb) of
packet used to get garbage values. In this case if
MWIFIEX_BUF_FLAG_REQUEUED_PKT flag is mistakenly set, txpd
header was skipped. This patch makes sure that tx_info is
correctly initialized to fix the problem.
Cc: <stable@vger.kernel.org>
Reported-by: Andrew Wiley <wiley.andrew.j@gmail.com>
Reported-by: Linus Gasser <list@markas-al-nour.org>
Reported-by: Michael Hirsch <hirsch@teufel.de>
Tested-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Maithili Hinge <maithili@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TDLS initiator is set once during link setup. If determines the
address ordering in the link identifier IE.
Fix dependent drivers - mwifiex and mac80211.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Why is converting time formats so desired if there are proper
interfaces for this?
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For users who do not need wowlan, load mwifiex.ko with
disconnect_on_suspend = 1; or iw phy0 wowlan disable.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When magic-packet is generated as a UDP packet the offset should
be 20+8 more bytes to cover IPv4 header and UDP header. So the
total offset become 56.
Add a new MEF entry to support both magic-packet patterns
generated by different tools.
Cc: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Zhiyuan Yang <yangzy@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A custom regulatory domain was introduced in this commit:
cc0ba0d mwifiex: support custom world regulatory domain
The commit description says that it was introduced because the world
regulatory domain does not include channels 52-64 and 100-140. These
channels are described in the world regulatory domain now, so we can
drop this custom regulatory domain.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On PCIe Tx data path, network interface specific tx_info
parameters such as bss_num and bss_type are saved at
"skb->cb + sizeof(dma_addr_t)" (returned by MWIFIEX_SKB_TXCB).
Later mwifiex_map_pci_memory() called from
mwifiex_pcie_send_data() will memcpy
sizeof(struct mwifiex_dma_mapping) bytes to save PCIe DMA
address and length information at beginning of skb->cb.
This accidently overwrites bss_num and bss_type saved in skb->cb
previously because bss_num/bss_type and mwifiex_dma_mapping data
overlap.
Similarly, on PCIe Rx data path, rx_info parameters overlaps
with PCIe DMA address and length information too.
Fix it by defining mwifiex_cb structure and having
MWIFIEX_SKB_TXCB and MWIFIEX_SKB_RXCB return the correct address
of tx_info/rx_info using the structure members.
Also add a BUILD_BUG_ON to maks sure that mwifiex_cb structure
doesn't exceed the size of skb->cb.
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Chin-Ran Lo <crlo@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If host sleep parameter gap is set to 0xff, firmware will wait
for an ack from host to confirm the success of host wakeup.
This prevents firmware from uploading data packet before host
actually wakes up.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current implementation sets tdls_link flag only while restoring
packets from TDLS queue. If traffic to peer starts after TDLS is
setup, there is no way to set TDLS link flag to true. Do this
while creating RA list and we confirm that there exist a TDLS
peer for which setup is complete.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
[113.967694] Unable to handle kernel NULL pointer dereference
at virtual address 00000020
............
[113.967859] PC is at mwifiex_update_rxreor_flags+0xfc/0x430
............
[113.968110] mwifiex_update_rxreor_flags+0xfc/0x430
[113.968129] mwifiex_handle_event_ext_scan_report+0x1e4/0x21c
[113.968148] mwifiex_process_sta_event+0x410/0x508
[113.968165] mwifiex_process_event+0x184/0x1e0
[113.968181] mwifiex_main_process+0x220/0x48c
[113.968197] mwifiex_sdio_interrupt+0xc8/0x1cc
[113.968210] sdio_irq_thread+0x11c/0x290
In case of legacy scan, adapter->curr_cmd is guranteed to be
non-NULL in check_next_scan_cmd. This may not be case in
extended scan where scan command response would come earlier and
set curr_cmd to NULL. Extended scan event comes later and while
trying to complete IOCTL for scan, driver would crash in
dereferencing adapter->curr_cmd->wait_q_enabled.
Avoid this by completing IOCTL in case of legacy scans only.
Internal scan would be completed while handling extended scan
command response.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To be future-proof and for better readability the time comparisons are
modified to use time_after() instead of plain, error-prone math.
Signed-off-by: Manuel Schölling <manuel.schoelling@gmx.de>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes the following warning:
CC drivers/net/wireless/mwifiex/tdls.o
drivers/net/wireless/mwifiex/tdls.c: In function ‘mwifiex_prep_tdls_encap_data’:
drivers/net/wireless/mwifiex/tdls.c:475:4: warning: passing argument 2 of ‘mwifiex_tdls_add_ht_oper’ discards ‘const’ qualifier from pointer target type [enabled by
default]
ret = mwifiex_tdls_add_ht_oper(priv, peer, 1, skb);
^
drivers/net/wireless/mwifiex/tdls.c:190:1: note: expected ‘u8 *’ but argument is of type ‘const u8 *’
mwifiex_tdls_add_ht_oper(struct mwifiex_private *priv, u8 *mac,
^
drivers/net/wireless/mwifiex/tdls.c:481:4: warning: passing argument 2 of ‘mwifiex_tdls_add_ht_oper’ discards ‘const’ qualifier from pointer target type [enabled by
default]
ret = mwifiex_tdls_add_ht_oper(priv, peer, 0, skb);
^
drivers/net/wireless/mwifiex/tdls.c:190:1: note: expected ‘u8 *’ but argument is of type ‘const u8 *’
mwifiex_tdls_add_ht_oper(struct mwifiex_private *priv, u8 *mac,
^
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds handling of updating rx sequence number for
packets received from TDLS peer. Current implementation of
mwifiex_queueing_ra_based assumes station would always receive
packets from AP which is not true in case of TDLS.
Fix this by adding this case.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes an issue where AMSDU packets for TDLS link
would flow over infra link. This happened because we were
missing setting TDLS flag in TxPD on AMSDU packets.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If userspace application does not take care of TDLS teardown
event, TDLS link would be present in driver database and thus
driver would send such packets on direct link while peer has
already severed link causing data traffic failure. Disable TDLS
link upon teardown event so as to ensure this does not happen.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If TDLS link delete command fails because of non-existent peer
or TDLS peer is absent from driver's entry, it means link was
already deleted. In such case print debug messages with lower
severity.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In station role if TDLS is supported, we traverse TDLS peer list
to see if packet's destination address matches with TDLS peer.
Packets destined to AP are not sent over TDLS link and hence
avoid this list traversal for such packets.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While sending null packet from driver we are passing NULL
tx_param pointer to indicate there are no more packets in queue.
PCIe send routine assumes caller has done sanity check on
tx_param and may cause crash while dereferencing next_pkt_len
from tx_param.
Avoid this by passing tx_param structure with next_pkt_len as
zero instead of NULL pointer.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During SDIO MP aggregation, we at first acquire current write
port to write data onto and then proceed with using this port
for SDIO write. If error occurs later in mwifiex_write_data_sync
because device is suspended or SDIO write failure, we do not
restore current write port and write bitmap. This results into
leaking one port and hole in SDIO write port bitmap.
Restore current write port and reset bitmap accordingly in
failure cases to avoid this.
Reported-by: James Cameron <quozl@laptop.org>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Reviewed-by: James Cameron <quozl@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support to populate HT operatation IE in TDLS
setup confirm command. This is required for setting wider
bandwidths for TDLS operations.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds code to disable TDLS link upon reception of TDLS
teardown event from peer. Teardown event can happen either
because of TDLS teardown packet from peer or internal timeout
configured during TDLS setup. Event is propogated to cfg80211
so that userspace application can take appropriate action.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds configuration timeout for TDLS link. This is
configuered at the time of TDLS link configuration. If TDLS link
is inactive for more than timeout, FW will tear this link.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit e050c76fcf.
I'm not sure what crack pipe I was using when I merged this...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently AMSDU and AMPDU aggregation is enabled for TID 0 to
TID 5 streams. Lets enable it for remaining two streams also.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will help to aggregate more packets which yields better
throughput results for 11ac chipsets.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will help to aggregate more packets which yields better
throughput results.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware dump feature is added for PCIe based chipsets.
Separate file will be created at /var/log/fw_dump_*
for each memory segment.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This option be useful to dump firmware memory for debugging
purpose. Actual code to dump firmware momory for SDIO and PCIe
chipsets will be added later.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When command timeout occurs due to a firmware/hardware bug,
there is no chance of next command being successful. We will
keep cmd_sent flag on so that next command won't be sent to
firmware.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IE's are parsed from beacon buffer and stored locally using
mwifiex_update_bss_desc_with_ie() function.
Sometimes the local pointers point to the data inside IE, but
while using them it is assumed that they are pointing to the IE
itself.
These issues are fixed in this patch.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'add_remove_card_sem' semaphore already takes care of
synchronization for driver load and unload threads.
Hence there won't be a case when unload thread is waiting on
'wait_for_completion(fw_load)'.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This option allows driver to finish pending operations in
disconnect handler by not killing URBs after usb_deregister
call.
We will get rid of global pointer 'usb_card' by moving code
from cleanup_module() to disconnect(). This will help to match
with our handling for SDIO and PCIe interfaces.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New skbs are allocated at the time of AMSDU aggregation. Setting
up in timestamps for such skbs was missing which would result
into wrong queue delays passed to FW. Fix this by setting
timestamp of skbs created for AMSDU aggregation.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Command nodes are increased from 20 to 50. Now we can always
scan 1 channel per scan command to avoid traffic delay/loss in
connected state. We will get rid of *CHANNEL_PER_SCAN_CMD macros
used due to command node constraints.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For PCIe, aggregate more AMSDU packets till PCIe TXBD is full.
For SDIO, aggregation was disabled for AMSDU packets because
AMSDU aggregated packet size is already 4K or 8K, SDIO Multiport
Aggregation feature didn't use to gain much previously.
Now with increased multiport aggregation buffer, we can enable
it for AMSDU packets.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently Tx and Rx buffer sizes are 8K and 16K respectively for
all chipsets. We will change them to 32K for SD8897 and 16K for
older chipsets. SD8897 chipset has more SDIO data ports than
older chipsets.
This patch will help to improve throughput numbers.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WARNING: single byte memset is suspicious.
Swapped 2nd/3rd argument?
This code happens to work because rx_mcs is the first variable
in mcs structure. We should use 'mcs.rx_mcs' here anyway.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Maithili Hinge <maithili@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes when command timeout occurs due to a firmware or
hardware bug, there may be some synchronous commands in command
queue. These commands are never downloaded to firmware causing
hung task warnings. This patch replaces wait_event_interruptible
call with wait_event_interruptible_timeout to fix the issue.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During extended scan, SCAN report event is always followed by
command response. Sometimes It is observed that command response
is processed before SCAN report which leads to a crash, because
current command node is cleared while handling the response.
This patch makes sure that driver's main thread gives priority
to events over command responses.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Maithili Hinge <maithili@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It has been observed that system hangs during suspend, if host
sleep activation fails due to a missing interrupt from firmware.
Use timeout variant, so that the thread will be woken up when
timer expires.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a thread is interrupted by signal, all
wait_event_interruptible calls after queueing commands return
an error. Numbers of commands in pending queue are increased
in this case. Sometimes all commands nodes in pool are filled.
We will cancel pending commands when signal is received.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When scan request is received, scan commands are prepared and
queued into scan pending queue. There is a corner case when
command nodes are full. So we stop queueing further scan
commands and return an error. This patch makes sure that
currently queued commands in scan pending queue are also freed
in this case.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes we may end up downloading other commands when host
sleep is configured. This patch makes sure that pending
commands are cancelled and we stop queueing further commands
during host sleep.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Incremented sequence number was not being used for SLEEP confirm
command. This patch fixes the issue.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When next scan command is delayed due to Tx traffic and
meanwhile synchronous command is received followed by a signal,
we cance all pending commands. NULL pointer dereference is seen
in this case while queueing next command in scan delay timer.
This patch adds a check to fix this issue.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Casting a pointer to a pointer of the same type is pointless,
so remove these unnecessary casts.
Done via coccinelle script:
$ cat typecast_2.cocci
@@
type T;
T *foo;
@@
- (T *)foo
+ foo
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To set AP in 1X1 or 2X2 mode through hostapd, we need to set
RX-STBC* in hostapd.conf file. Depending upon RX-STBC bit in
ht_cap IE received from hostapd, we need to update mcs set in
bss_cfg appropriately before starting AP.
Signed-off-by: Maithili Hinge <maithili@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support to read sleep cookie for command
response before accessing buffer.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stations associated to mwifiex AP would not be able to ping AP
after scan was issued on AP interface. This happened because
there was no handling of extended scan event in AP. This patch
adds this handling and fixes ping failure issue.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
drivers/net/usb/r8152.c
drivers/net/xen-netback/netback.c
Both the r8152 and netback conflicts were simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently AMPDU aggregation is preferred over AMSDU. AMSDU
aggregation is performed only if AMPDU streams in firmware
are full.
This patch adds simultaneous AMSDU and AMPDU aggregation
support. This mechanism helps to improve throughput.
AMSDU is enabled only for 8897 chipsets which supports 4K
transmit buffer. User can disable AMSDU using
'disable_tx_amsdu' module parameter.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Existing mwifiex_11n_dispatch_pkt() function is renamed as
mwifiex_11n_dispatch_pkt_until_start_win() and a new function
mwifiex_11n_dispatch_pkt() is created for a common code which
dispatches single packet based on interface type.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use negative check for 'status' and return from the function.
This improves readability by avoiding line splits. Also, local
variable is used for start window calculations.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As V15 firmware supports VHT rate configuration, we can use this
information received in set bitrate mask handler.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware API version number will be used for future patches
to support different firmware API specs.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While preparing association request, intersection of device's
VHT capability information and corresponding field advertised
by AP is used.
This patch fixes a couple errors while saving and copying vht_cap
and vht_oper fields from AP's beacon.
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While preparing association request, intersection of device's HT
capability information and corresponding fields advertised by AP
is used.
This patch fixes an error while copying this field from AP's
beacon.
Cc: <stable@vger.kernel.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/mwifiex/pcie.c
net/ipv6/sit.c
The SIT driver conflict consists of a bug fix being done by hand
in 'net' (missing u64_stats_init()) whilst in 'net-next' a helper
was created (netdev_alloc_pcpu_stats()) which takes care of this.
The two wireless conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of an explicit cast, use the min_t macro.
Signed-off-by: Silvan Jegen <s.jegen@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Even if the device is changed to 1X1 mode, data is sent with
higher MCS rates after association.
This patch fixes the problem by updating MCS information field
in HT capability when antenna setting changes so that correct
information will be advertised in association and probe request.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Command timeout happens when firmware goes into bad state.
There is no chance that next command will be successful after
this. Hence we will maintain a flag instead of count.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We already have one in mwifiex_adapter structure.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a check in command preparation routine.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Deauth is sent to AP when the device is acting as station at
shutdown time. Similarly we should stop AP operation also.
mwifiex_deauthenticate() takes care closing the connection
based on provided interface type.
Add a new function to simplify the code.
Reported-by: Avery Pennarun <apenwarr@gmail.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We skip downloading other commands after FUNC_SHUTDOWN is queued
during driver unload. Main thread should be woken up each time
after freeing skipped command so that FUNC_SHUTDOWN gets served
in case if there are other pending commands before FUNC_SHUTDOWN.
Also, call mwifiex_complete_cmd() only for synchronous commands.
Reported-by: Avery Pennarun <apenwarr@gmail.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Maithili Hinge <maithili@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwifiex_cancel_pending_ioctl() and
mwifiex_cancel_all_pending_cmd() are called in command timeout
and driver unload paths respectively.
If scan operation is in progress, we should abort it smoothly.
Reported-by: Tim Shepard <shep@alum.mit.edu>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently default Tx buffer size configured to firmware is 2K
for all chipsets. This patch changes it to 4K for SD/PCIe/USB
8897 chipsets as per firmware requirements.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a race condition while queuing synchronous command and
asynchronous command requested from different threads, because
the wait_q_enabled flag is set based on a global variable
cmd_wait_q_required.
The issue is fixed by removing this global variable and using a
unified function with an argument 'sync' passed into the
function.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some stations reset the sequence number for traffic-ids (TIDs)
as they initiate a block-ACK session. In order to detect such
behavior, mwifiex must note the starting sequence number given
during the ADDBA request. If the first received sequence number
after the ADDBA falls outside the receive window for this TID but
after the the ADDBA starting sequence number, we can assume that
this AP has reset its sequence number during the ADDBA. In this
case we must adjust the input window backward to incorporate this
received sequence number instead of ignoring it. Otherwise, we
could fail to successfully retrieve an arbitrarily large number
of downstream frames at the beginning of the block-ACK session.
Signed-off-by: Paul Stewart <pstew@chromium.org>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As many Surface Pro I & II users have found out, the mwifiex_usb
doesn't support usb autosuspend, and it has caused some system
stability issues.
Bug 69661 - mwifiex_usb on MS Surface Pro 1 is unstable
Bug 60815 - Interface hangs in mwifiex_usb
Bug 64111 - mwifiex_usb USB8797 crash failed to get signal
information
USB autosuspend get triggered when Surface Pro's AC power is
removed or powertop enables power saving on USB8797 device.
Driver's suspend handler is called here, but resume handler
won't be called until the AC power is put back on or powertop
disables power saving for USB8797.
We need to refactor the suspend/resume handlers to support
usb autosuspend properly. For now let's just remove it.
Cc: <stable@vger.kernel.org> # 3.5+
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't perform OBSS scan internally. As we intend to use
corresponding feature in application, we will enable this flag.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While modifying timer, we need not delete timer.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use SMP safe del_timer_sync instead of del_timer for cancelling
timers.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a typo here because the names are confusingly similar. The
intent was sizeof(struct ieee80211_vht_cap) (size 12) but sizeof(struct
ieee80211_ht_cap) (size 32) was used.
Anway, it's cleaner to just specify the variable instead of the type.
Fixes: 5f6d598339 ('mwifiex: add VHT support for TDLS')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both libertas USB driver and mwifiex_usb driver are registerring
with name 'usb8xxx'. The following conflict happens while trying
to load both drivers.
[6.211307] Error: Driver 'usb8xxx' is already registered...
[6.217261] mwifiex_usb: Driver register failed!
Fix it by renaming mwifiex_usb driver's name.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We are sending sleep confirm done interrupt in the middle of
sleep handshake. There is a corner case when Tx done interrupt
is received from firmware during sleep handshake due to which
host and firmware power states go out of sync causing cmd and
Tx data timeout problem.
Hence sleep confirm done interrupt is sent at the end of sleep
handshake to fix the problem.
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We may get a NULL pointer here if skb allocation for Rx packet
was failed earlier.
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Write io memory to clean PCIe buffer only when PCIe device is
present else this results into crash because of invalid memory
access.
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While framing the TDLS Setup Confirmation frame, the driver needs to
know if the TDLS peer is VHT/HT/WMM capable and thus shall construct
the VHT/HT operation / WMM parameter elements accordingly. Supplicant
determines if the TDLS peer is VHT/HT/WMM capable based on the
presence of the respective IEs in the received TDLS Setup Response frame.
The host driver should not need to parse the received TDLS Response
frame and thus, should be able to rely on the supplicant to indicate
the capability of the peer through additional flags while transmitting
the TDLS Setup Confirmation frame through tdls_mgmt operations.
Signed-off-by: Sunil Dutt Undekari <usdutt@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a new argument for ndo_select_queue() callback that passes a
fallback handler. This gets invoked through netdev_pick_tx();
fallback handler is currently __netdev_pick_tx() as most drivers
invoke this function within their customized implementation in
case for skbs that don't need any special handling. This fallback
handler can then be replaced on other call-sites with different
queue selection methods (e.g. in packet sockets, pktgen etc).
This also has the nice side-effect that __netdev_pick_tx() is
then only invoked from netdev_pick_tx() and export of that
function to modules can be undone.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds key material V2 support to mwifiex.
Newer FW supports this feature and FW KEY API version is used
to determine which command structure needs to be used.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Avinash Patil