Commit Graph

161 Commits

Author SHA1 Message Date
Michael Schmitz 3f90f9ef2d m68k/mm: Adjust VM area to be unmapped by gap size for __iounmap()
If 020/030 support is enabled, get_io_area() leaves an IO_SIZE gap
between mappings which is added to the vm_struct representing the
mapping.  __ioremap() uses the actual requested size (after alignment),
while __iounmap() is passed the size from the vm_struct.

On 020/030, early termination descriptors are used to set up mappings of
extent 'size', which are validated on unmapping. The unmapped gap of
size IO_SIZE defeats the sanity check of the pmd tables, causing
__iounmap() to loop forever on 030.

On 040/060, unmapping of page table entries does not check for a valid
mapping, so the umapping loop always completes there.

Adjust size to be unmapped by the gap that had been added in the
vm_struct prior.

This fixes the hang in atari_platform_init() reported a long time ago,
and a similar one reported by Finn recently (addressed by removing
ioremap() use from the SWIM driver.

Tested on my Falcon in 030 mode - untested but should work the same on
040/060 (the extra page tables cleared there would never have been set
up anyway).

Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
[geert: Minor commit description improvements]
[geert: This was fixed in 2.4.23, but not in 2.5.x]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@vger.kernel.org
2018-05-24 12:00:27 +02:00
Eric W. Biederman 3c67075d5d signal/m68k: Use force_sig_fault where appropriate
Filling in struct siginfo before calling force_sig_info a tedious and
error prone process, where once in a great while the wrong fields
are filled out, and siginfo has been inconsistently cleared.

Simplify this process by using the helper force_sig_fault.  Which
takes as a parameters all of the information it needs, ensures
all of the fiddly bits of filling in struct siginfo are done properly
and then calls force_sig_info.

In short about a 5 line reduction in code for every time force_sig_info
is called, which makes the calling function clearer.

Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
2018-04-25 10:41:01 -05:00
Geert Uytterhoeven 31833332f7 m68k/mm: Stop printing the virtual memory layout
Since commit ad67b74d24 ("printk: hash addresses printed with
%p"), the virtual memory layout printed during boot up contains "ptrval"
instead of actual addresses:

    Memory: 268040K/276480K available (2979K kernel code, 310K rwdata, 784K rodata, 144K init, 172K bss, 8440K reserved, 0K cma-reserved)
    Virtual kernel memory layout:
	vector  : 0x003d2e74 - 0x003d3274   (   1 KiB)
	kmap    : 0xd0000000 - 0xf0000000   ( 512 MiB)
	vmalloc : 0x11800000 - 0xd0000000   (3048 MiB)
	lowmem  : 0x00000000 - 0x11000000   ( 272 MiB)
	  .init : 0x(ptrval) - 0x(ptrval)   ( 144 KiB)
	  .text : 0x(ptrval) - 0x(ptrval)   (2980 KiB)
	  .data : 0x(ptrval) - 0x(ptrval)   (1095 KiB)
	  .bss  : 0x(ptrval) - 0x(ptrval)   ( 173 KiB)

Instead of changing the printing to "%px", and leaking virtual memory
layout information again, just remove the printing completely, cfr. e.g.
commit 071929dbdd ("arm64: Stop printing the virtual memory
layout").

All interesting information (actual section sizes) is already printed by
mem_init_print_info() just above anyway.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2018-03-19 10:22:59 +01:00
Eric W. Biederman 5f74972ce6 signal: Don't use structure initializers for struct siginfo
The siginfo structure has all manners of holes with the result that a
structure initializer is not guaranteed to initialize all of the bits.
As we have to copy the structure to userspace don't even try to use
a structure initializer.  Instead use clear_siginfo followed by initializing
selected fields.  This gives a guarantee that uninitialized kernel memory
is not copied to userspace.

Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
2018-01-22 19:07:08 -06:00
Greg Ungerer f55ab8f275 m68k: fix ColdFire node shift size calculation
The m68k pg_data_table is a fix size array defined in arch/m68k/mm/init.c.
Index numbers within it are defined based on memory size. But for Coldfire
these don't take into account a non-zero physical RAM base address, and this
causes us to access past the end of this array at system start time.

Change the node shift calculation so that we keep the index inside its range.

Reported-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
2017-11-06 08:25:20 +10:00
Greg Ungerer 34fa9b2177 m68k: move coldfire MMU initialization code
The M54[78]x ColdFire parts are not the only members of the ColdFire family
that have an MMU. But currently some of the early MMU initialization code
is inside the startup code specific to only the ColdFire M54[78]x parts.
Move that early ColdFire MMU init code so that it is run for other ColdFire
parts running with MMU enabled.

Specifically this means that the MMU initialization code will now also be
run for the ColdFire M5441x parts when running with MMU enabled.

The code move meant that the extern definition for the mmu_context_init()
function had to be moved as well. To make it clear that is ColdFire specific
I have renamed that with a "cf_" in front of it and put its extern definition
in the mcfmmu.h (which is already included by the setup code).

Reported-by: Angelo Dureghello <angelo@sysam.it>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
2017-11-06 08:25:20 +10:00
Greg Kroah-Hartman b24413180f License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier.  The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
 - file had no licensing information it it.
 - file was a */uapi/* one with no licensing information in it,
 - file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne.  Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed.  Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
 - Files considered eligible had to be source code files.
 - Make and config files were included as candidates if they contained >5
   lines of source
 - File already had some variant of a license header in it (even if <5
   lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

 - when both scanners couldn't find any license traces, file was
   considered to have no license information in it, and the top level
   COPYING file license applied.

   For non */uapi/* files that summary was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0                                              11139

   and resulted in the first patch in this series.

   If that file was a */uapi/* path one, it was "GPL-2.0 WITH
   Linux-syscall-note" otherwise it was "GPL-2.0".  Results of that was:

   SPDX license identifier                            # files
   ---------------------------------------------------|-------
   GPL-2.0 WITH Linux-syscall-note                        930

   and resulted in the second patch in this series.

 - if a file had some form of licensing information in it, and was one
   of the */uapi/* ones, it was denoted with the Linux-syscall-note if
   any GPL family license was found in the file or had no licensing in
   it (per prior point).  Results summary:

   SPDX license identifier                            # files
   ---------------------------------------------------|------
   GPL-2.0 WITH Linux-syscall-note                       270
   GPL-2.0+ WITH Linux-syscall-note                      169
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause)    21
   ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause)    17
   LGPL-2.1+ WITH Linux-syscall-note                      15
   GPL-1.0+ WITH Linux-syscall-note                       14
   ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause)    5
   LGPL-2.0+ WITH Linux-syscall-note                       4
   LGPL-2.1 WITH Linux-syscall-note                        3
   ((GPL-2.0 WITH Linux-syscall-note) OR MIT)              3
   ((GPL-2.0 WITH Linux-syscall-note) AND MIT)             1

   and that resulted in the third patch in this series.

 - when the two scanners agreed on the detected license(s), that became
   the concluded license(s).

 - when there was disagreement between the two scanners (one detected a
   license but the other didn't, or they both detected different
   licenses) a manual inspection of the file occurred.

 - In most cases a manual inspection of the information in the file
   resulted in a clear resolution of the license that should apply (and
   which scanner probably needed to revisit its heuristics).

 - When it was not immediately clear, the license identifier was
   confirmed with lawyers working with the Linux Foundation.

 - If there was any question as to the appropriate license identifier,
   the file was flagged for further research and to be revisited later
   in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.  The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
 - a full scancode scan run, collecting the matched texts, detected
   license ids and scores
 - reviewing anything where there was a license detected (about 500+
   files) to ensure that the applied SPDX license was correct
 - reviewing anything where there was no detection but the patch license
   was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
   SPDX license was correct

This produced a worksheet with 20 files needing minor correction.  This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg.  Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected.  This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.)  Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-02 11:10:55 +01:00
Al Viro 68acfdcb47 m68k: switch to generic extable.h
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2017-03-28 18:23:40 -04:00
Mathias Krause 3dfe33020c m68k/sun3: Remove dead code in paging_init()
The macro TEST_VERIFY_AREA can never be defined as there's no
wp_works_ok variable. So just remove the dead code.

Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2017-02-13 10:03:19 +01:00
Geert Uytterhoeven e6991137a3 m68k/mm: Modernize printing of kernel messages
Convert from printk() to pr_*().

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2017-02-12 10:36:53 +01:00
Geert Uytterhoeven 05b70ff69c m68k/mm: sun3 - Modernize printing of kernel messages
- Convert from printk() to pr_*(),
  - Add missing print to do_page_mapin(), as print_pte_vaddr() calls
    pr_cont().

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2017-02-12 10:36:53 +01:00
Linus Torvalds 7c0f6ba682 Replace <asm/uaccess.h> with <linux/uaccess.h> globally
This was entirely automated, using the script by Al:

  PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
  sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
        $(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)

to do the replacement at the end of the merge window.

Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-12-24 11:46:01 -08:00
Greg Ungerer f71160655d m68k: move ColdFire _bootmem_alloc code
The early ColdFire bootmem_alloc() code is currently only included in
the board support for the Coldire 54xx platforms. It will be used on all
ColdFire MMU enabled platforms as others are supported. So move the
mcf54xx_bootmem_alloc() function to be generally available to all MMU
enabled ColdFire parts (and use a more generic name for it).

Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
2016-09-26 12:02:58 +10:00
Kirill A. Shutemov dcddffd41d mm: do not pass mm_struct into handle_mm_fault
We always have vma->vm_mm around.

Link: http://lkml.kernel.org/r/1466021202-61880-8-git-send-email-kirill.shutemov@linux.intel.com
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2016-07-26 16:19:19 -07:00
Geert Uytterhoeven 79ae4fa5c0 m68k/mm: motorola - Add missing initialization of max_pfn
If max_pfn is not initialized, the various /proc/kpage* files are empty,
and selftests/vm/mlock2-tests will fail. max_pfn is also used by the
block layer to calculate DMA masks.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
2015-11-22 11:35:24 +01:00
David Hildenbrand 70ffdb9393 mm/fault, arch: Use pagefault_disable() to check for disabled pagefaults in the handler
Introduce faulthandler_disabled() and use it to check for irq context and
disabled pagefaults (via pagefault_disable()) in the pagefault handlers.

Please note that we keep the in_atomic() checks in place - to detect
whether in irq context (in which case preemption is always properly
disabled).

In contrast, preempt_disable() should never be used to disable pagefaults.
With !CONFIG_PREEMPT_COUNT, preempt_disable() doesn't modify the preempt
counter, and therefore the result of in_atomic() differs.
We validate that condition by using might_fault() checks when calling
might_sleep().

Therefore, add a comment to faulthandler_disabled(), describing why this
is needed.

faulthandler_disabled() and pagefault_disable() are defined in
linux/uaccess.h, so let's properly add that include to all relevant files.

This patch is based on a patch from Thomas Gleixner.

Reviewed-and-tested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: David.Laight@ACULAB.COM
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: airlied@linux.ie
Cc: akpm@linux-foundation.org
Cc: benh@kernel.crashing.org
Cc: bigeasy@linutronix.de
Cc: borntraeger@de.ibm.com
Cc: daniel.vetter@intel.com
Cc: heiko.carstens@de.ibm.com
Cc: herbert@gondor.apana.org.au
Cc: hocko@suse.cz
Cc: hughd@google.com
Cc: mst@redhat.com
Cc: paulus@samba.org
Cc: ralf@linux-mips.org
Cc: schwidefsky@de.ibm.com
Cc: yang.shi@windriver.com
Link: http://lkml.kernel.org/r/1431359540-32227-7-git-send-email-dahi@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
2015-05-19 08:39:15 +02:00
Linus Torvalds 33692f2759 vm: add VM_FAULT_SIGSEGV handling support
The core VM already knows about VM_FAULT_SIGBUS, but cannot return a
"you should SIGSEGV" error, because the SIGSEGV case was generally
handled by the caller - usually the architecture fault handler.

That results in lots of duplication - all the architecture fault
handlers end up doing very similar "look up vma, check permissions, do
retries etc" - but it generally works.  However, there are cases where
the VM actually wants to SIGSEGV, and applications _expect_ SIGSEGV.

In particular, when accessing the stack guard page, libsigsegv expects a
SIGSEGV.  And it usually got one, because the stack growth is handled by
that duplicated architecture fault handler.

However, when the generic VM layer started propagating the error return
from the stack expansion in commit fee7e49d45 ("mm: propagate error
from stack expansion even for guard page"), that now exposed the
existing VM_FAULT_SIGBUS result to user space.  And user space really
expected SIGSEGV, not SIGBUS.

To fix that case, we need to add a VM_FAULT_SIGSEGV, and teach all those
duplicate architecture fault handlers about it.  They all already have
the code to handle SIGSEGV, so it's about just tying that new return
value to the existing code, but it's all a bit annoying.

This is the mindless minimal patch to do this.  A more extensive patch
would be to try to gather up the mostly shared fault handling logic into
one generic helper routine, and long-term we really should do that
cleanup.

Just from this patch, you can generally see that most architectures just
copied (directly or indirectly) the old x86 way of doing things, but in
the meantime that original x86 model has been improved to hold the VM
semaphore for shorter times etc and to handle VM_FAULT_RETRY and other
"newer" things, so it would be a good idea to bring all those
improvements to the generic case and teach other architectures about
them too.

Reported-and-tested-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Jan Engelhardt <jengelh@inai.de>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> # "s390 still compiles and boots"
Cc: linux-arch@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-01-29 10:51:32 -08:00
Himangi Saraogi f0b99a643e m68k/mm: Eliminate memset after alloc_bootmem_pages
alloc_bootmem and related functions always return a zeroed region of memory.
Thus a memset after calls to these functions is unnecessary.

The following Coccinelle semantic patch was used for making the change:

@@
expression E,E1;
@@

E = \(alloc_bootmem\|alloc_bootmem_low\|alloc_bootmem_pages\|alloc_bootmem_low_pages\)(...)
... when != E
- memset(E,0,E1);

Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2014-11-10 09:56:44 +01:00
Geert Uytterhoeven 24cae7934c m68k: Reformat arch/m68k/mm/hwtest.c
No functional changes

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2014-10-03 10:50:56 +02:00
Geert Uytterhoeven e4dc601bf9 m68k: Disable/restore interrupts in hwreg_present()/hwreg_write()
hwreg_present() and hwreg_write() temporarily change the VBR register to
another vector table. This table contains a valid bus error handler
only, all other entries point to arbitrary addresses.

If an interrupt comes in while the temporary table is active, the
processor will start executing at such an arbitrary address, and the
kernel will crash.

While most callers run early, before interrupts are enabled, or
explicitly disable interrupts, Finn Thain pointed out that macsonic has
one callsite that doesn't, causing intermittent boot crashes.
There's another unsafe callsite in hilkbd.

Fix this for good by disabling and restoring interrupts inside
hwreg_present() and hwreg_write().

Explicitly disabling interrupts can be removed from the callsites later.

Reported-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@vger.kernel.org
2014-10-03 10:50:56 +02:00
Andreas Schwab 486df8bc46 m68k: Increase initial mapping to 8 or 16 MiB if possible
If the size of the first memory chunk is at least 8 or 16 MiB increase the
initial mapping to 8 resp. 16 MiB instead of 4 MiB.
This makes it possible to
  1. Map more memory in the first node without running out of space for the
     page tables,
  2. Boot kernels that don't fit in 4 MiB (e.g. multi_defconfig).

Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>

  - Add support for 8 MiB,
  - Store initial mapping size in head.S for later reuse,
  - Add comment about large kernels.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2014-05-28 10:11:54 +02:00
Geert Uytterhoeven f6fc30dbb7 m68k/mm: kmap spelling/grammar fixes
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2013-12-30 21:01:11 +01:00
Geert Uytterhoeven 8e398f6381 m68k: Convert arch/m68k/mm/fault.c to pr_*()
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2013-12-30 21:01:10 +01:00
Geert Uytterhoeven 4e25c0e92f m68k/mm: Check for mm != NULL in do_page_fault() debug code
When DEBUG is enabled, do_page_fault() may dereference a NULL pointer,
causing recursive bus errors.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2013-12-30 21:01:09 +01:00
Geert Uytterhoeven 799300840c m68k/UAPI: Move generic definitions to <asm/bootinfo.h>
Move generic definitions used by bootstraps to uapi/asm/bootinfo.h:
  - Machine types,
  - CPU, FPU, and MMU types,
  - struct mem_info.

Keep a copy of struct mem_info for in-kernel use, and rename it to struct
m68k_mem_info, as the exported one will be modified later.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2013-11-26 11:09:16 +01:00
Johannes Weiner 759496ba64 arch: mm: pass userspace fault flag to generic fault handler
Unlike global OOM handling, memory cgroup code will invoke the OOM killer
in any OOM situation because it has no way of telling faults occuring in
kernel context - which could be handled more gracefully - from
user-triggered faults.

Pass a flag that identifies faults originating in user space from the
architecture-specific fault handlers to generic code so that memcg OOM
handling can be improved.

Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: David Rientjes <rientjes@google.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: azurIt <azurit@pobox.sk>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-09-12 15:38:01 -07:00
Jiang Liu 3e548a9e88 mm/m68k: fix build warning of unused variable
Fix build warning of unused variable:

  arch/m68k/mm/init.c: In function 'mem_init': arch/m68k/mm/init.c:151:6: warning: unused variable 'i' [-Wunused-variable]

Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-07-03 16:07:39 -07:00
Jiang Liu b69a9787b1 mm/m68k: prepare for killing free_all_bootmem_node()
Prepare for killing free_all_bootmem_node() by using free_all_bootmem().

Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-07-03 16:07:38 -07:00
Jiang Liu 9671468f1e mm/m68k: prepare for removing num_physpages and simplify mem_init()
Prepare for removing num_physpages and simplify mem_init().

Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-07-03 16:07:36 -07:00
Jiang Liu 0c98853473 mm: concentrate modification of totalram_pages into the mm core
Concentrate code to modify totalram_pages into the mm core, so the arch
memory initialized code doesn't need to take care of it.  With these
changes applied, only following functions from mm core modify global
variable totalram_pages: free_bootmem_late(), free_all_bootmem(),
free_all_bootmem_node(), adjust_managed_page_count().

With this patch applied, it will be much more easier for us to keep
totalram_pages and zone->managed_pages in consistence.

Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Acked-by: David Howells <dhowells@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: <sworddragon2@aol.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Michel Lespinasse <walken@google.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-07-03 16:07:33 -07:00
Jiang Liu dbe67df4ba mm: enhance free_reserved_area() to support poisoning memory with zero
Address more review comments from last round of code review.
1) Enhance free_reserved_area() to support poisoning freed memory with
   pattern '0'. This could be used to get rid of poison_init_mem()
   on ARM64.
2) A previous patch has disabled memory poison for initmem on s390
   by mistake, so restore to the original behavior.
3) Remove redundant PAGE_ALIGN() when calling free_reserved_area().

Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: <sworddragon2@aol.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Michel Lespinasse <walken@google.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-07-03 16:07:32 -07:00
Jiang Liu 11199692d8 mm: change signature of free_reserved_area() to fix building warnings
Change signature of free_reserved_area() according to Russell King's
suggestion to fix following build warnings:

  arch/arm/mm/init.c: In function 'mem_init':
  arch/arm/mm/init.c:603:2: warning: passing argument 1 of 'free_reserved_area' makes integer from pointer without a cast [enabled by default]
    free_reserved_area(__va(PHYS_PFN_OFFSET), swapper_pg_dir, 0, NULL);
    ^
  In file included from include/linux/mman.h:4:0,
                   from arch/arm/mm/init.c:15:
  include/linux/mm.h:1301:22: note: expected 'long unsigned int' but argument is of type 'void *'
   extern unsigned long free_reserved_area(unsigned long start, unsigned long end,

   mm/page_alloc.c: In function 'free_reserved_area':
>> mm/page_alloc.c:5134:3: warning: passing argument 1 of 'virt_to_phys' makes pointer from integer without a cast [enabled by default]
   In file included from arch/mips/include/asm/page.h:49:0,
                    from include/linux/mmzone.h:20,
                    from include/linux/gfp.h:4,
                    from include/linux/mm.h:8,
                    from mm/page_alloc.c:18:
   arch/mips/include/asm/io.h:119:29: note: expected 'const volatile void *' but argument is of type 'long unsigned int'
   mm/page_alloc.c: In function 'free_area_init_nodes':
   mm/page_alloc.c:5030:34: warning: array subscript is below array bounds [-Warray-bounds]

Also address some minor code review comments.

Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: <sworddragon2@aol.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Michel Lespinasse <walken@google.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-07-03 16:07:32 -07:00
Jiang Liu 920f1ad081 mm/m68k: use common help functions to free reserved pages
Use common help functions to free reserved pages.

Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2013-04-29 15:54:30 -07:00
Thadeu Lima de Souza Cascardo be3f695cbe m68knommu: fix build when CPU is not coldfire
Commit dd1cb3a7c4 [merge MMU and non-MMU
versions of mm/init.c] unified mm/init.c for both MMU and non-MMU m68k
platforms. However, it broke when we build a non-MMU M68K Classic CPU kernel.

This fix builds a section that came from the MMU version only when we are
building a MMU kernel.

Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2013-03-04 11:08:39 +10:00
Greg Ungerer d6fccc7563 m68k: fix conditional use of init_pointer_table
Compiling 3.8-rc1 fails for some m68k targets (the non-mmu ones) with:

  CC      arch/m68k/mm/init.o
arch/m68k/mm/init.c: In function ‘mem_init’:
arch/m68k/mm/init.c:191:2: error: implicit declaration of function ‘init_pointer_table’
arch/m68k/mm/init.c:191:36: error: ‘kernel_pg_dir’ undeclared (first use in this function)
arch/m68k/mm/init.c:191:36: note: each undeclared identifier is reported only once for each function it appears in
arch/m68k/mm/init.c:192:18: error: ‘PTRS_PER_PGD’ undeclared (first use in this function)
arch/m68k/mm/init.c:194:4: error: implicit declaration of function ‘__pgd_page’
arch/m68k/mm/init.c:198:6: error: ‘zero_pgtable’ undeclared (first use in this function)
make[2]: *** [arch/m68k/mm/init.o] Error 1
make[1]: *** [arch/m68k/mm] Error 2
make[1]: Leaving directory `/home/gerg/new-wave.git/linux-3.x'
make: *** [linux] Error 1

Change the conditions that define init_pointer_table so that it matches what
actually uses it.

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2013-01-07 16:13:04 +10:00
Greg Ungerer f50bf88df3 m68k: move to a single instance of free_initmem()
Currently each sub-architecture has its own implementation if init_freemem().
There is two different cases that the various implementations deal with.
They either free the init memory, or they don't. We only need a single instance
to cover all cases.

The non-MMU version did some page alignment twidling, but this is not
neccessary. The current linker script enforces page alignment. It also
checked for CONFIG_RAMKERNEL, but this also is not necessary, the linker
script always keeps the init sections in RAM.

The MMU ColdFire version of free_initmem() was empty. There is no reason it
can't carry out the freeing of the init memory. So it is now changed and
tested to do this.

For the other MMU cases the code is the same. For the general Motorola MMU
case we free the init memory. For the SUN3 case we do nothing (though I
think it could safely free the init memory as well).

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2012-11-14 08:50:56 +01:00
Greg Ungerer dd1cb3a7c4 m68k: merge MMU and non-MMU versions of mm/init.c
Some of the code in the existing mm/init_mm.c and mm/init_no.c files is
the same, and if we merge them back to a single file we can save some code
duplication.

Although the old mem_init() code for non-MMU was a little different than
the MMU version, it turns out we can use the same code. So I now we just
use the MMU mem_init() code for all. It also means we now get identical
console info messages for this code on kernel boot up.

So merge the two files back into a single file.

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2012-11-14 08:50:56 +01:00
Shaohua Li 45cac65b0f readahead: fault retry breaks mmap file read random detection
.fault now can retry.  The retry can break state machine of .fault.  In
filemap_fault, if page is miss, ra->mmap_miss is increased.  In the second
try, since the page is in page cache now, ra->mmap_miss is decreased.  And
these are done in one fault, so we can't detect random mmap file access.

Add a new flag to indicate .fault is tried once.  In the second try, skip
ra->mmap_miss decreasing.  The filemap_fault state machine is ok with it.

I only tested x86, didn't test other archs, but looks the change for other
archs is obvious, but who knows :)

Signed-off-by: Shaohua Li <shaohua.li@fusionio.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2012-10-09 16:22:47 +09:00
Linus Torvalds 587a9e1f95 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k updates from Geert Uytterhoeven.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k: Make sys_atomic_cmpxchg_32 work on classic m68k
  m68k/apollo: Rename "timer" to "apollo_timer"
  zorro: Remove unused zorro_bus.devices
  m68k: Remove never used asm/shm.h
  m68k/sun3: Remove unselectable code in prom_init()
  m68k: Use asm-generic version of <asm/sections.h>
  m68k: Replace m68k-specific _[se]bss by generic __bss_{start,stop}
  mtd/uclinux: Use generic __bss_stop instead of _ebss
  m68knommu: Allow ColdFire CPUs to use unaligned accesses
  m68k: Remove five unused headers
  m68k: CPU32 does not support unaligned accesses
  m68k: Introduce config option CPU_HAS_NO_UNALIGNED
  m68k: delay, muldi3 - Use CONFIG_CPU_HAS_NO_MULDIV64
  m68k: Move CPU_HAS_* config options
  m68k: Remove duplicate FPU config option
  m68knommu: Clean up printing of sections
  m68k: Use asm-generic version of <asm/types.h>
  m68k: Use Kbuild logic to import asm-generic headers
2012-08-03 10:52:41 -07:00
Greg Ungerer f3ff6432dd m68k: fix ColdFire clear cache operation
The code for clearing (invalidating) the ColdFire cache is actually performing
a push operation. Add functions to clear the cache, and fix cache_clear() to
call the appropriate clear cache function.

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2012-07-17 15:49:34 +10:00
Geert Uytterhoeven dc0610518f m68k: Replace m68k-specific _[se]bss by generic __bss_{start,stop}
BSS_SECTION() provides the __bss_{start,stop} symbols, so there's no need
to wrap our own _[se]bss around it.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer<gerg@uclinux.org>
2012-06-27 09:59:43 +02:00
Kautuk Consul b637a6b167 m68k/mm: Port OOM changes to do_page_fault()
Commit d065bd810b
(mm: retry page fault when blocking on disk transfer) and
commit 37b23e0525
(x86,mm: make pagefault killable)

The above commits introduced changes into the x86 pagefault handler
for making the page fault handler retryable as well as killable.

These changes reduce the mmap_sem hold time, which is crucial
during OOM killer invocation.

Port these changes to m68k.

Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2012-04-22 20:16:49 +02:00
David Howells 803f69144f Disintegrate asm/system.h for M68K
Disintegrate asm/system.h for M68K.

Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Greg Ungerer <gerg@uclinux.org>
cc: linux-m68k@lists.linux-m68k.org
2012-03-28 18:30:02 +01:00
Alexander Stein 3372f5a7d0 m68k: Do not set global share for non-kernel shared pages
If the SG bit is set in MMUTR the page is accessible for all
userspace processes (ignoring the ASID). So a process might randomly
access a page from a different process which had a shared page
(from shared memory) in its context.

Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2012-02-07 11:25:57 +10:00
Linus Torvalds 0dbfe8ddaa Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k: Fix assembler constraint to prevent overeager gcc optimisation
  mac_esp: rename irq
  mac_scsi: dont enable mac_scsi irq before requesting it
  macfb: fix black and white modes
  m68k/irq: Remove obsolete IRQ_FLG_* definitions

Fix up trivial conflict in arch/m68k/kernel/process_mm.c as per Geert.
2012-01-26 12:43:57 -08:00
Andreas Schwab 2a3535069e m68k: Fix assembler constraint to prevent overeager gcc optimisation
Passing the address of a variable as an operand to an asm statement
doesn't mark the value of this variable as used, so gcc may optimize its
initialisation away.  Fix this by using the "m" constraint instead.

Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@vger.kernel.org
2012-01-22 14:50:20 +01:00
Greg Ungerer fbe3364ac4 m68k: add ColdFire with MMU enabled support to the m68k mem init code
The ColdFire has similar setup requirements to the SUN3 code, so we
use that.

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
2011-12-30 10:20:48 +10:00
Greg Ungerer 0e6782c880 m68k: compile appropriate mm arch files for ColdFire MMU support
Create a config symbol to enable when using a ColdFire MMU. We then
use that to only compile the necessary arch mm files.

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
2011-12-30 10:20:39 +10:00
Greg Ungerer 066bf87b5c m68k: ColdFire V4e MMU paging init code and miss handler
The different ColdFire V4e MMU requires its own dedicated paging init
code, and a TLB miss handler for its software driven TLB.

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
2011-12-30 10:20:38 +10:00
Greg Ungerer d49316e84b m68k: use ColdFire MMU read/write bit flags when ioremapping
The ColdFire MMU has separate read and write bits, unlike the Motorola
m68k MMU which has a single read-only bit.

Define a _PAGE_READWRITE value for the Motorola MMU, which is 0, so we
can unconditionaly include that in the page table entry bits when setting
up ioremapped pages.

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
2011-12-30 10:20:37 +10:00
Greg Ungerer 6061019255 m68k: modify cache push and clear code for ColdFire with MMU enable
The cache push and clear code only need to flush the branch cache on
the write-through cache setup of the ColdFire V4e with MMU enabled.

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
2011-12-30 10:20:36 +10:00
Greg Ungerer ae2eca724a m68k: add cache support for V4e ColdFire cores running with MMU enabled
Add code to deal with instruction, data and branch caches of the V4e
ColdFire cores when they are running with the MMU enabled.

This code is loosely based on Freescales changes for the caches of the
V4e ColdFire in the 2.6.25 kernel BSP. That code was originally by
Kurt Mahan <kmahan@freescale.com> (now <kmahan@xmission.com>).

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
2011-12-30 10:20:28 +10:00
Greg Ungerer e87c09a899 m68k: print memory layout info in boot log
Output a table of the kernel memory regions at boot time.
This is taken directly from the ARM architecture code that does this.
The table looks like this:

Virtual kernel memory layout:
    vector  : 0x00000000 - 0x00000400   (   0 KiB)
    kmap    : 0xd0000000 - 0xe0000000   ( 256 MiB)
    vmalloc : 0xc0000000 - 0xcfffffff   ( 255 MiB)
    lowmem  : 0x00000000 - 0x02000000   (  32 MiB)
      .init : 0x00128000 - 0x00134000   (  48 KiB)
      .text : 0x00020000 - 0x00118d54   ( 996 KiB)
      .data : 0x00118d60 - 0x00126000   (  53 KiB)
      .bss  : 0x00134000 - 0x001413e0   (  53 KiB)

This has been very useful while debugging the ColdFire virtual memory
support code. But in general I think it is nice to know extacly where
the kernel has layed everything out on boot.

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2011-12-24 21:47:57 +10:00
Greg Ungerer 7a79a80f50 m68knommu: create common externs for _ram* vars
Create common extern definitions of _rambase, _ramstart and _ramend
instead of them being externed when used in code.

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2011-10-18 14:22:26 +10:00
Greg Ungerer 3998bfbf31 m68knommu: remove extern declarations of memory_start/memory_end from mm/init
We do not need to have local extern declarations of memory_start and
memory_end in mm/init_no.c. There are declarations already in asm/page_no.h.

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2011-10-18 14:22:26 +10:00
Greg Ungerer 9da48c01f5 m68knommu: use generic section names in mm/init code
We should be including and using sections.h to get at the extern
definitions of the linker sections in the m68knommu mm init code.
Not defining them locally.

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2011-10-18 14:22:26 +10:00
Linus Torvalds 968e75fc13 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k/math-emu: Remove unnecessary code
  m68k/math-emu: Remove commented out old code
  m68k: Kill warning in setup_arch() when compiling for Sun3
  m68k/atari: Prefix GPIO_{IN,OUT} with CODEC_
  sparc: iounmap() and *_free_coherent() - Use lookup_resource()
  m68k/atari: Reserve some ST-RAM early on for device buffer use
  m68k/amiga: Chip RAM - Use lookup_resource()
  resources: Add lookup_resource()
  sparc: _sparc_find_resource() should check for exact matches
  m68k/amiga: Chip RAM - Offset resource end by CHIP_PHYSADDR
  m68k/amiga: Chip RAM - Use resource_size() to fix off-by-one error
  m68k/amiga: Chip RAM - Change chipavail to an atomic_t
  m68k/amiga: Chip RAM - Always allocate from the start of memory
  m68k/amiga: Chip RAM - Convert from printk() to pr_*()
  m68k/amiga: Chip RAM - Use tabs for indentation
2011-07-31 14:30:59 -10:00
Michael Schmitz 217bbd8188 m68k/atari: Reserve some ST-RAM early on for device buffer use
Based on an original patch from Michael Schmitz:

Because mem_init() is now called before device init, devices that rely on
ST-RAM may find all ST-RAM already allocated to other users by the time
device init happens. In particular, a large initrd RAM disk may use up
enough of ST-RAM to cause atari_stram_alloc() to resort to
__get_dma_pages() allocation.

In the current state of Atari memory management, all of RAM is marked
DMA capable, so __get_dma_pages() may well return RAM that is not in actual
fact DMA capable. Using this for frame buffer or SCSI DMA buffer causes
subtle failure.

The ST-RAM allocator has been changed to allocate memory from a pool of
reserved ST-RAM of configurable size, set aside on ST-RAM init (i.e.
before mem_init()). As long as this pool is not exhausted, allocation of
real ST-RAM can be guaranteed.

Other changes:
  - Replace the custom allocator in the ST-RAM pool by the existing allocator
    in the resource subsystem,
  - Remove mem_init_done and its hook, as memory init is now done before
    device init,
  - Remove /proc/stram, as ST-RAM usage now shows up under /proc/iomem, e.g.

	005f2000-006f1fff : ST-RAM Pool
	  005f2000-0063dfff : atafb
	  0063e000-00641fff : ataflop
	  00642000-00642fff : SCSI

Signed-off-by: Michael Schmitz <schmitz@debian.org>
[Andreas Schwab <schwab@linux-m68k.org>: Use memparse()]
[Geert: Use the resource subsystem instead of a custom allocator]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2011-07-30 21:21:39 +02:00
Geert Uytterhoeven 6617eaf33d m68knommu: Fix printk() format in free_initrd_mem()
arch/m68k/mm/init_no.c:123: warning: format "%d" expects type "int", but argument 2 has type "long unsigned int"

And use pr_notice() while we're at it.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2011-07-25 10:44:04 +10:00
Geert Uytterhoeven 45d1564cce m68knommu: Make empty_zero_page "void *", like on m68k
This allows to get rid of the casts.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2011-07-25 10:44:04 +10:00
Peter Zijlstra 1c39517696 mm: now that all old mmu_gather code is gone, remove the storage
Fold all the mmu_gather rework patches into one for submission

Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reported-by: Hugh Dickins <hughd@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Miller <davem@davemloft.net>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Tony Luck <tony.luck@intel.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2011-05-25 08:39:16 -07:00
Greg Ungerer b1ffa25925 m68knommu: clean up mm/init_no.c
The memory initialization code for m68knommu has grown a bit crufty,
clean it up.

. remove unused declaration for die_if_kernel()
. remove un-needed declaration of free_initmem()
. removed unused definitions of empty_bad_page and empty_bad_page_table
. removed unused DEBUG code
. make free_initmem() proper prototype

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2011-05-24 10:03:51 +10:00
Greg Ungerer f225c86750 m68k: merge the mmu and non-mmu mm/Makefile
Its is trivial to megre the mmu and non-mmu arch/m68k/mm/Makefile's back
into a single file. So do it.

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2011-05-24 10:03:50 +10:00
Greg Ungerer 1bccc43c10 m68k: mv kmap_mm.c to kmap.c
The non-mmu kmap_no.c has been removed. So we can move kmap_mm.c
back to being the only kmap.c.

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2011-05-24 10:03:50 +10:00
Greg Ungerer 593732bd41 m68knommu: remove stubs for __ioremap() and iounmap()
The implementation of iounmap() and __ioremap() for non-mmu m68k is
trivial. We can inline them in m68knommu headers and remove the trivial
implementations.

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2011-05-24 10:03:50 +10:00
Greg Ungerer 92474a2513 m68knommu: remove unused kernel_set_cachemode()
None of the m68knommu platforms will ever use kernel_set_cachemode().
And it is specific to a couple of m68k devices. So remove it.

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2011-05-24 10:03:50 +10:00
Michael Schmitz 4aac0b4815 m68k/mm: Set all online nodes in N_NORMAL_MEMORY
For m68k, N_NORMAL_MEMORY represents all nodes that have present memory
since it does not support HIGHMEM.  This patch sets the bit at the time
node_present_pages has been set by free_area_init_node.
At the time the node is brought online, the node state would have to be
done unconditionally since information about present memory has not yet
been recorded.

If N_NORMAL_MEMORY is not accurate, slub may encounter errors since it
uses this nodemask to setup per-cache kmem_cache_node data structures.

This pach is an alternative to the one proposed by David Rientjes
<rientjes@google.com> attempting to set node state immediately when
bringing the node online.

Signed-off-by: Michael Schmitz <schmitz@debian.org>
Tested-by: Thorsten Glaser <tg@debian.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
CC: stable@kernel.org
2011-04-27 17:36:00 +02:00
Greg Ungerer 66d857b08b m68k: merge m68k and m68knommu arch directories
There is a lot of common code that could be shared between the m68k
and m68knommu arch branches. It makes sense to merge the two branches
into a single directory structure so that we can more easily share
that common code.

This is a brute force merge, based on a script from Stephen King
<sfking@fdwdc.com>, which was originally written by Arnd Bergmann
<arnd@arndb.de>.

> The script was inspired by the script Sam Ravnborg used to merge the
> includes from m68knommu. For those files common to both arches but
> differing in content, the m68k version of the file is renamed to
> <file>_mm.<ext> and the m68knommu version of the file is moved into the
> corresponding m68k directory and renamed <file>_no.<ext> and a small
> wrapper file <file>.<ext> is used to select between the two version. Files
> that are common to both but don't differ are removed from the m68knommu
> tree and files and directories that are unique to the m68knommu tree are
> moved to the m68k tree. Finally, the arch/m68knommu tree is removed.
>
> To select between the the versions of the files, the wrapper uses
>
> #ifdef CONFIG_MMU
> #include <file>_mm.<ext>
> #else
> #include <file>_no.<ext>
> #endif

On top of this file merge I have done a simplistic merge of m68k and
m68knommu Kconfig, which primarily attempts to keep existing options and
menus in place. Other than a handful of options being moved it produces
identical .config outputs on m68k and m68knommu targets I tested it on.

With this in place there is now quite a bit of scope for merge cleanups
in future patches.

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2011-03-25 14:05:13 +10:00
Roman Zippel dcdf3a2935 m68k: Add helper function handle_kernel_fault()
Add helper function handle_kernel_fault() in signal.c, so frame_extra_sizes
can become static, and to avoid future code duplication.

Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2011-03-16 19:10:40 +01:00
Nick Piggin adbf6e6952 m68k: invoke oom-killer from page fault
As explained in commit 1c0fe6e3bd, we want to call the architecture independent
oom killer when getting an unexplained OOM from handle_mm_fault, rather than
simply killing current.

Cc: linux-m68k@lists.linux-m68k.org
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-arch@vger.kernel.org
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: David Rientjes <rientjes@google.com>
[Geert] Kill 2 introduced compiler warnings
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2010-05-17 21:37:39 +02:00
Tejun Heo 5a0e3ad6af include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.

Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-30 22:02:32 +09:00
Philippe De Muyter f351d4bb3c m68k{,nommu}/h8300: Remove obsolete comment about map_chunk
Remove the comments referring to a function map_chunk that no longer exists.

Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2010-02-27 18:27:14 +01:00
Philippe De Muyter 88cb773c5f m68k: Allow ioremapping top of memory
The test in __ioremap to reject memory ranges crossing the 0 boundary
rejects also memory ranges ending at the end of the memory.  Fix that.

Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2010-02-27 18:27:13 +01:00
Geert Uytterhoeven cc013a8890 arches: drop superfluous casts in nr_free_pages() callers
Commit 9617729941 ("Drop free_pages()")
modified nr_free_pages() to return 'unsigned long' instead of 'unsigned
int'.  This made the casts to 'unsigned long' in most callers superfluous,
so remove them.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Chris Zankel <zankel@tensilica.com>
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-22 07:17:34 -07:00
Linus Torvalds d06063cc22 Move FAULT_FLAG_xyz into handle_mm_fault() callers
This allows the callers to now pass down the full set of FAULT_FLAG_xyz
flags to handle_mm_fault().  All callers have been (mechanically)
converted to the new calling convention, there's almost certainly room
for architectures to clean up their code and then add FAULT_FLAG_RETRY
when that support is added.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-06-21 13:08:22 -07:00
Geert Uytterhoeven c85627fbf5 m68k: Kill several external declarations in source files
- Replace external declarations by proper includes where availiable.
    The accesses to some symbols had to be modified, as before they were
    declared using e.g. "extern int _end", while asm-generic/sections.h uses
    e.g. "extern char _end[]"
  - Remove unused or superfluous external declarations

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2009-01-12 20:56:34 +01:00
Julia Lawall 79aa79bac9 arch/m68k/mm/kmap.c: introduce missing kfree
Error handling code following a kmalloc should free the allocated data.

The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,l;
position p1,p2;
expression *ptr != NULL;
@@

(
if ((x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...)) == NULL) S
|
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
..
if (x == NULL) S
)
<... when != x
     when != if (...) { <+...x...+> }
x->f = E
..>
(
 return \(0\|<+...x...+>\|ptr\);
|
 return@p2 ...;
)

@script:python@
p1 << r.p1;
p2 << r.p2;
@@

print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-14 10:23:27 -07:00
Johannes Weiner 969eefb516 m68k: use generic show_mem()
Remove arch-specific show_mem() in favor of the generic version.

This also removes the following redundant information display:

	- free pages, printed by show_free_areas()
	- pages in swapcache, printed by show_swap_cache_info()

where show_mem() calls show_free_areas(), which calls
show_swap_cache_info().

Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-26 12:00:11 -07:00
Johannes Weiner 9109fb7b35 mm: drop unneeded pgdat argument from free_area_init_node()
free_area_init_node() gets passed in the node id as well as the node
descriptor.  This is redundant as the function can trivially get the node
descriptor itself by means of NODE_DATA() and the node's id.

I checked all the users and NODE_DATA() seems to be usable everywhere
from where this function is called.

Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 10:47:16 -07:00
Johannes Weiner b61bfa3c46 mm: move bootmem descriptors definition to a single place
There are a lot of places that define either a single bootmem descriptor or an
array of them.  Use only one central array with MAX_NUMNODES items instead.

Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Kyle McMartin <kyle@parisc-linux.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24 10:47:14 -07:00
Julia Lawall 93026e217b arch/m68k/mm/sun3mmu.c: Eliminate NULL test and memset after alloc_bootmem
As noted by Akinobu Mita in patch b1fceac2b9,
alloc_bootmem and related functions never return NULL and always return a
zeroed region of memory.  Thus a NULL test or memset after calls to these
functions is unnecessary.

This was fixed using the following semantic patch.
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
expression E;
statement S;
@@

E = \(alloc_bootmem\|alloc_bootmem_low\|alloc_bootmem_pages\|alloc_bootmem_low_pages\)(...)
.. when != E
(
- BUG_ON (E == NULL);
|
- if (E == NULL) S
)

@@
expression E,E1;
@@

E = \(alloc_bootmem\|alloc_bootmem_low\|alloc_bootmem_pages\|alloc_bootmem_low_pages\)(...)
.. when != E
- memset(E,0,E1);
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-20 17:24:40 -07:00
Julia Lawall 7b6b948fc0 arch/m68k/mm/motorola.c: Eliminate NULL test and memset after alloc_bootmem
As noted by Akinobu Mita in patch b1fceac2b9,
alloc_bootmem and related functions never return NULL and always return a
zeroed region of memory.  Thus a NULL test or memset after calls to these
functions is unnecessary.

This was fixed using the following semantic patch.
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
expression E;
statement S;
@@

E = \(alloc_bootmem\|alloc_bootmem_low\|alloc_bootmem_pages\|alloc_bootmem_low_pages\)(...)
.. when != E
(
- BUG_ON (E == NULL);
|
- if (E == NULL) S
)

@@
expression E,E1;
@@

E = \(alloc_bootmem\|alloc_bootmem_low\|alloc_bootmem_pages\|alloc_bootmem_low_pages\)(...)
.. when != E
- memset(E,0,E1);
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-20 17:24:40 -07:00
Aneesh Kumar K.V 5fcf430303 m68k: Export empty_zero_page for ZERO_PAGE usage in modules.
ext4 uses ZERO_PAGE(0) to zero out blocks.  We need to export
different symbols in different arches for the usage of ZERO_PAGE
in modules.

Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
2008-04-29 08:11:12 -04:00
Johannes Weiner 6feef6e5f2 m68k: remove redundant display of free swap space in show_mem()
show_mem() has no need to print the amount of free swap space manually because
show_free_areas() does this already and is called by the former.

The two outputs only differ in text formatting:

  printk("Free swap  = %lukB\n", ...);
  printk("Free swap:       %6ldkB\n", ...);

Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-28 08:58:27 -07:00
Serge E. Hallyn b460cbc581 pid namespaces: define is_global_init() and is_container_init()
is_init() is an ambiguous name for the pid==1 check.  Split it into
is_global_init() and is_container_init().

A cgroup init has it's tsk->pid == 1.

A global init also has it's tsk->pid == 1 and it's active pid namespace
is the init_pid_ns.  But rather than check the active pid namespace,
compare the task structure with 'init_pid_ns.child_reaper', which is
initialized during boot to the /sbin/init process and never changes.

Changelog:

	2.6.22-rc4-mm2-pidns1:
	- Use 'init_pid_ns.child_reaper' to determine if a given task is the
	  global init (/sbin/init) process. This would improve performance
	  and remove dependence on the task_pid().

	2.6.21-mm2-pidns2:

	- [Sukadev Bhattiprolu] Changed is_container_init() calls in {powerpc,
	  ppc,avr32}/traps.c for the _exception() call to is_global_init().
	  This way, we kill only the cgroup if the cgroup's init has a
	  bug rather than force a kernel panic.

[akpm@linux-foundation.org: fix comment]
[sukadev@us.ibm.com: Use is_global_init() in arch/m32r/mm/fault.c]
[bunk@stusta.de: kernel/pid.c: remove unused exports]
[sukadev@us.ibm.com: Fix capability.c to work with threaded init]
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Acked-by: Pavel Emelianov <xemul@openvz.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: Herbert Poetzel <herbert@13thfloor.at>
Cc: Kirill Korotaev <dev@sw.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-19 11:53:37 -07:00
Will Schmidt dcca2bde4f During VM oom condition, kill all threads in process group
We have had complaints where a threaded application is left in a bad state
after one of it's threads is killed when we hit a VM: out_of_memory
condition.

Killing just one of the process threads can leave the application in a bad
state, whereas killing the entire process group would allow for the
application to restart, or be otherwise handled, and makes it very obvious
that something has gone wrong.

This change allows the entire process group to be taken down, rather
than just the one thread.

Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16 09:42:52 -07:00
Geert Uytterhoeven fb425d0b93 m68k: Kill superfluous extern
Kill a superfluous extern declaration

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-08-22 19:52:45 -07:00
Al Viro 66a3f820cb m68k: missing __init
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-20 08:24:49 -07:00
Al Viro 88f8bb780e m68k: missing exports
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-20 08:24:49 -07:00
Nick Piggin 83c54070ee mm: fault feedback #2
This patch completes Linus's wish that the fault return codes be made into
bit flags, which I agree makes everything nicer.  This requires requires
all handle_mm_fault callers to be modified (possibly the modifications
should go further and do things like fault accounting in handle_mm_fault --
however that would be for another patch).

[akpm@linux-foundation.org: fix alpha build]
[akpm@linux-foundation.org: fix s390 build]
[akpm@linux-foundation.org: fix sparc build]
[akpm@linux-foundation.org: fix sparc64 build]
[akpm@linux-foundation.org: fix ia64 build]
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Still apparently needs some ARM and PPC loving - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-19 10:04:41 -07:00
Roman Zippel 12d810c1b8 m68k: discontinuous memory support
Fix support for discontinuous memory

Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-31 07:58:14 -07:00
Roman Zippel fbe9c96129 m68k: runtime patching infrastructure
Add the basic infrastructure to allow runtime patching of kernel and modules
to optimize a few functions with parameters, which are only calculated once
during bootup and are otherwise constant.  Use this for the conversion between
virtual and physical addresses.

Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-31 07:58:13 -07:00
Robert P. J. Day 5cbded585d [PATCH] getting rid of all casts of k[cmz]alloc() calls
Run this:

	#!/bin/sh
	for f in $(grep -Erl "\([^\)]*\) *k[cmz]alloc" *) ; do
	  echo "De-casting $f..."
	  perl -pi -e "s/ ?= ?\([^\)]*\) *(k[cmz]alloc) *\(/ = \1\(/" $f
	done

And then go through and reinstate those cases where code is casting pointers
to non-pointers.

And then drop a few hunks which conflicted with outstanding work.

Cc: Russell King <rmk@arm.linux.org.uk>, Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Karsten Keil <kkeil@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Steven French <sfrench@us.ibm.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-13 09:05:58 -08:00
Geert Uytterhoeven bf8af91bcd [PATCH] m68k: EXPORT_SYMBOL(cache_{clear,push}) bogus comment
Remove bogus comments about unexporting cache_{push,clear}(), as inline
dma_cache_maintenance() (used by at least bionet and pamsnet) calls them.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-09 09:41:18 -08:00
Sam Creasey a3a79bd7c7 [PATCH] Sun3: General updates
General compile fixes for 2.6.16 for sun3, and some updates to make the new
bootloader work correctly.  Tested on 3/50, 3/60, 3/80.

Signed-off-by: Sam Creasey <sammy@sammy.net>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-09 09:41:18 -08:00
Peter Zijlstra 6edaf68a87 [PATCH] mm: arch do_page_fault() vs in_atomic()
In light of the recent pagefault and filemap_copy_from_user work I've gone
through all the arch pagefault handlers to make sure the inc_preempt_count()
'feature' works as expected.

Several sections of code (including the new filemap_copy_from_user) rely on
the fact that faults do not take locks under increased preempt count.

arch/x86_64 - good
arch/powerpc - good
arch/cris - fixed
arch/i386 - good
arch/parisc - fixed
arch/sh - good
arch/sparc - good
arch/s390 - good
arch/m68k - fixed
arch/ppc - good
arch/alpha - fixed
arch/mips - good
arch/sparc64 - good
arch/ia64 - good
arch/arm - fixed
arch/um - good
arch/avr32 - good
arch/h8300 - NA
arch/m32r - good
arch/v850 - good
arch/frv - fixed
arch/m68knommu - NA
arch/arm26 - fixed
arch/sh64 - fixed
arch/xtensa - good

Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-07 08:39:21 -08:00
Al Viro 2e811488ce [PATCH] clean m68k ksyms
sun3_ksyms gone, m68k_ksyms trimmed down to exports of the assembler ones,
for sun3 added the missing exports of __ioremap() and iounmap().

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-11 11:17:06 -07:00
Al Viro 437111ca38 [PATCH] sun3 __iomem annotations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-11 11:17:06 -07:00
Uwe Zeisberger f30c226954 fix file specification in comments
Many files include the filename at the beginning, serveral used a wrong one.

Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-10-03 23:01:26 +02:00
Sukadev Bhattiprolu f400e198b2 [PATCH] pidspace: is_init()
This is an updated version of Eric Biederman's is_init() patch.
(http://lkml.org/lkml/2006/2/6/280).  It applies cleanly to 2.6.18-rc3 and
replaces a few more instances of ->pid == 1 with is_init().

Further, is_init() checks pid and thus removes dependency on Eric's other
patches for now.

Eric's original description:

	There are a lot of places in the kernel where we test for init
	because we give it special properties.  Most  significantly init
	must not die.  This results in code all over the kernel test
	->pid == 1.

	Introduce is_init to capture this case.

	With multiple pid spaces for all of the cases affected we are
	looking for only the first process on the system, not some other
	process that has pid == 1.

Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: Serge Hallyn <serue@us.ibm.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: <lxc-devel@lists.sourceforge.net>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-09-29 09:18:12 -07:00