This fixes a counter problem on 32bit systems:
When the rx_bytes counter reached 2 GiB, it jumpd to (2^64 Bytes - 2GiB) Bytes.
rtnl_link_stats64 has __u64 type and atomic_long_read returns
atomic_long_t which is signed. Due to the conversation
we get an incorrect value on 32bit systems if the MSB of
the atomic_long_t value is set.
CC: Tom Parkin <tparkin@katalix.com>
Fixes: 7b7c0719cd ("l2tp: avoid deadlock in l2tp stats update")
Signed-off-by: Dominik Heidler <dheidler@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Network devices can allocate reasources and private memory using
netdev_ops->ndo_init(). However, the release of these resources
can occur in one of two different places.
Either netdev_ops->ndo_uninit() or netdev->destructor().
The decision of which operation frees the resources depends upon
whether it is necessary for all netdev refs to be released before it
is safe to perform the freeing.
netdev_ops->ndo_uninit() presumably can occur right after the
NETDEV_UNREGISTER notifier completes and the unicast and multicast
address lists are flushed.
netdev->destructor(), on the other hand, does not run until the
netdev references all go away.
Further complicating the situation is that netdev->destructor()
almost universally does also a free_netdev().
This creates a problem for the logic in register_netdevice().
Because all callers of register_netdevice() manage the freeing
of the netdev, and invoke free_netdev(dev) if register_netdevice()
fails.
If netdev_ops->ndo_init() succeeds, but something else fails inside
of register_netdevice(), it does call ndo_ops->ndo_uninit(). But
it is not able to invoke netdev->destructor().
This is because netdev->destructor() will do a free_netdev() and
then the caller of register_netdevice() will do the same.
However, this means that the resources that would normally be released
by netdev->destructor() will not be.
Over the years drivers have added local hacks to deal with this, by
invoking their destructor parts by hand when register_netdevice()
fails.
Many drivers do not try to deal with this, and instead we have leaks.
Let's close this hole by formalizing the distinction between what
private things need to be freed up by netdev->destructor() and whether
the driver needs unregister_netdevice() to perform the free_netdev().
netdev->priv_destructor() performs all actions to free up the private
resources that used to be freed by netdev->destructor(), except for
free_netdev().
netdev->needs_free_netdev is a boolean that indicates whether
free_netdev() should be done at the end of unregister_netdevice().
Now, register_netdevice() can sanely release all resources after
ndo_ops->ndo_init() succeeds, by invoking both ndo_ops->ndo_uninit()
and netdev->priv_destructor().
And at the end of unregister_netdevice(), we invoke
netdev->priv_destructor() and optionally call free_netdev().
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need to verify that cfg->ifname is unique at this point.
register_netdev() will return -EEXIST if asked to create a device with
a name that's alrealy in use.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export type of l2tpeth interfaces to userspace
(/sys/class/net/<iface>/uevent).
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Acked-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export naming scheme used when creating l2tpeth interfaces
(/sys/class/net/<iface>/name_assign_type). This let userspace know if
the device's name has been generated automatically or defined manually.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Acked-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MTU overhead calculation in L2TP device set-up
merged via commit b784e7ebfc
needs to be adjusted to lock the tunnel socket while
referencing the sub-data structures to derive the
socket's IP overhead.
Reported-by: Guillaume Nault <g.nault@alphalink.fr>
Tested-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: R. Parameswaran <rparames@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts were simply overlapping changes. In the net/ipv4/route.c
case the code had simply moved around a little bit and the same fix
was made in both 'net' and 'net-next'.
In the net/sched/sch_generic.c case a fix in 'net' happened at
the same time that a new argument was added to qdisc_hash_add().
Signed-off-by: David S. Miller <davem@davemloft.net>
l2tp_tunnel_find() and l2tp_tunnel_find_nth() don't modify "net".
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make l2tp_pernet()'s parameter constant, so that l2tp_session_get*() can
declare their "net" variable as "const".
Also constify "ifname" in l2tp_session_get_by_ifname().
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no point in checking for duplicate sessions at the beginning of
l2tp_nl_cmd_session_create(); the ->session_create() callbacks already
return -EEXIST when the session already exists.
Furthermore, even if l2tp_session_find() returns NULL, a new session
might be created right after the test. So relying on ->session_create()
to avoid duplicate session is the only sane behaviour.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
pppol2tp_getsockopt() doesn't take into account the error code returned
by pppol2tp_tunnel_getsockopt() or pppol2tp_session_getsockopt(). If
error occurs there, pppol2tp_getsockopt() continues unconditionally and
reports erroneous values.
Fixes: fd558d186d ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
pppol2tp_setsockopt() unconditionally overwrites the error value
returned by pppol2tp_tunnel_setsockopt() or
pppol2tp_session_setsockopt(), thus hiding errors from userspace.
Fixes: fd558d186d ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Existing L2TP kernel code does not derive the optimal MTU for Ethernet
pseudowires and instead leaves this to a userspace L2TP daemon or
operator. If an MTU is not specified, the existing kernel code chooses
an MTU that does not take account of all tunnel header overheads, which
can lead to unwanted IP fragmentation. When L2TP is used without a
control plane (userspace daemon), we would prefer that the kernel does a
better job of choosing a default pseudowire MTU, taking account of all
tunnel header overheads, including IP header options, if any. This patch
addresses this.
Change-set here uses the new kernel function, kernel_sock_ip_overhead(),
to factor the outer IP overhead on the L2TP tunnel socket (including
IP Options, if any) when calculating the default MTU for an Ethernet
pseudowire, along with consideration of the inner Ethernet header.
Signed-off-by: R. Parameswaran <rparames@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPP pseudo-wire type is 7 (11 is L2TP_PWTYPE_IP).
Fixes: f1f39f9110 ("l2tp: auto load type modules")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take a reference on the sessions returned by l2tp_session_find_nth()
(and rename it l2tp_session_get_nth() to reflect this change), so that
caller is assured that the session isn't going to disappear while
processing it.
For procfs and debugfs handlers, the session is held in the .start()
callback and dropped in .show(). Given that pppol2tp_seq_session_show()
dereferences the associated PPPoL2TP socket and that
l2tp_dfs_seq_session_show() might call pppol2tp_show(), we also need to
call the session's .ref() callback to prevent the socket from going
away from under us.
Fixes: fd558d186d ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts")
Fixes: 0ad6614048 ("l2tp: Add debugfs files for dumping l2tp debug info")
Fixes: 309795f4be ("l2tp: Add netlink control API for L2TP")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Callers of l2tp_nl_session_find() need to hold a reference on the
returned session since there's no guarantee that it isn't going to
disappear from under them.
Relying on the fact that no l2tp netlink message may be processed
concurrently isn't enough: sessions can be deleted by other means
(e.g. by closing the PPPOL2TP socket of a ppp pseudowire).
l2tp_nl_cmd_session_delete() is a bit special: it runs a callback
function that may require a previous call to session->ref(). In
particular, for ppp pseudowires, the callback is l2tp_session_delete(),
which then calls pppol2tp_session_close() and dereferences the PPPOL2TP
socket. The socket might already be gone at the moment
l2tp_session_delete() calls session->ref(), so we need to take a
reference during the session lookup. So we need to pass the do_ref
variable down to l2tp_session_get() and l2tp_session_get_by_ifname().
Since all callers have to be updated, l2tp_session_find_by_ifname() and
l2tp_nl_session_find() are renamed to reflect their new behaviour.
Fixes: 309795f4be ("l2tp: Add netlink control API for L2TP")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
l2tp_session_find() doesn't take any reference on the returned session.
Therefore, the session may disappear while sending the notification.
Use l2tp_session_get() instead and decrement session's refcount once
the notification is sent.
Fixes: 33f72e6f0c ("l2tp : multicast notification to the registered listeners")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
l2tp_session_create() relies on its caller for checking for duplicate
sessions. This is racy since a session can be concurrently inserted
after the caller's verification.
Fix this by letting l2tp_session_create() verify sessions uniqueness
upon insertion. Callers need to be adapted to check for
l2tp_session_create()'s return code instead of calling
l2tp_session_find().
pppol2tp_connect() is a bit special because it has to work on existing
sessions (if they're not connected) or to create a new session if none
is found. When acting on a preexisting session, a reference must be
held or it could go away on us. So we have to use l2tp_session_get()
instead of l2tp_session_find() and drop the reference before exiting.
Fixes: d9e31d17ce ("l2tp: Add L2TP ethernet pseudowire support")
Fixes: fd558d186d ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Holding a reference on session is required before calling
pppol2tp_session_ioctl(). The session could get freed while processing the
ioctl otherwise. Since pppol2tp_session_ioctl() uses the session's socket,
we also need to take a reference on it in l2tp_session_get().
Fixes: fd558d186d ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Taking a reference on sessions in l2tp_recv_common() is racy; this
has to be done by the callers.
To this end, a new function is required (l2tp_session_get()) to
atomically lookup a session and take a reference on it. Callers then
have to manually drop this reference.
Fixes: fd558d186d ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Rx path may grab the socket right before pppol2tp_release(), but
nothing guarantees that it will enqueue packets before
skb_queue_purge(). Therefore, the socket can be destroyed without its
queues fully purged.
Fix this by purging queues in pppol2tp_session_destruct() where we're
guaranteed nothing is still referencing the socket.
Fixes: 9e9cb6221a ("l2tp: fix userspace reception on plain L2TP sockets")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code following l2tp_tunnel_find() expects that a new reference is
held on sk. Either sk_receive_skb() or the discard_put error path will
drop a reference from the tunnel's socket.
This issue exists in both l2tp_ip and l2tp_ip6.
Fixes: a3c18422a4 ("l2tp: hold socket before dropping lock in l2tp_ip{, 6}_recv()")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Don't save TIPC header values before the header has been validated,
from Jon Paul Maloy.
2) Fix memory leak in RDS, from Zhu Yanjun.
3) We miss to initialize the UID in the flow key in some paths, from
Julian Anastasov.
4) Fix latent TOS masking bug in the routing cache removal from years
ago, also from Julian.
5) We forget to set the sockaddr port in sctp_copy_local_addr_list(),
fix from Xin Long.
6) Missing module ref count drop in packet scheduler actions, from
Roman Mashak.
7) Fix RCU annotations in rht_bucket_nested, from Herbert Xu.
8) Fix use after free which happens because L2TP's ipv4 support returns
non-zero values from it's backlog_rcv function which ipv4 interprets
as protocol values. Fix from Paul Hüber.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (35 commits)
qed: Don't use attention PTT for configuring BW
qed: Fix race with multiple VFs
l2tp: avoid use-after-free caused by l2tp_ip_backlog_recv
xfrm: provide correct dst in xfrm_neigh_lookup
rhashtable: Fix RCU dereference annotation in rht_bucket_nested
rhashtable: Fix use before NULL check in bucket_table_free
net sched actions: do not overwrite status of action creation.
rxrpc: Kernel calls get stuck in recvmsg
net sched actions: decrement module reference count after table flush.
lib: Allow compile-testing of parman
ipv6: check sk sk_type and protocol early in ip_mroute_set/getsockopt
sctp: set sin_port for addr param when checking duplicate address
net/mlx4_en: fix overflow in mlx4_en_init_timestamp()
netfilter: nft_set_bitmap: incorrect bitmap size
net: s2io: fix typo argumnet argument
net: vxge: fix typo argumnet argument
netfilter: nf_ct_expect: Change __nf_ct_expect_check() return value.
ipv4: mask tos for input route
ipv4: add missing initialization for flowi4_uid
lib: fix spelling mistake: "actualy" -> "actually"
...
Now that %z is standartised in C99 there is no reason to support %Z.
Unlike %L it doesn't even make format strings smaller.
Use BUILD_BUG_ON in a couple ATM drivers.
In case anyone didn't notice lib/vsprintf.o is about half of SLUB which
is in my opinion is quite an achievement. Hopefully this patch inspires
someone else to trim vsprintf.c more.
Link: http://lkml.kernel.org/r/20170103230126.GA30170@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
l2tp_ip_backlog_recv may not return -1 if the packet gets dropped.
The return value is passed up to ip_local_deliver_finish, which treats
negative values as an IP protocol number for resubmission.
Signed-off-by: Paul Hüber <phueber@kernsp.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
While destroying a network namespace that contains a L2TP tunnel a
"BUG: scheduling while atomic" can be observed.
Enabling lockdep shows that this is happening because l2tp_exit_net()
is calling l2tp_tunnel_closeall() (via l2tp_tunnel_delete()) from
within an RCU critical section.
l2tp_exit_net() takes rcu_read_lock_bh()
<< list_for_each_entry_rcu() >>
l2tp_tunnel_delete()
l2tp_tunnel_closeall()
__l2tp_session_unhash()
synchronize_rcu() << Illegal inside RCU critical section >>
BUG: sleeping function called from invalid context
in_atomic(): 1, irqs_disabled(): 0, pid: 86, name: kworker/u16:2
INFO: lockdep is turned off.
CPU: 2 PID: 86 Comm: kworker/u16:2 Tainted: G W O 4.4.6-at1 #2
Hardware name: Xen HVM domU, BIOS 4.6.1-xs125300 05/09/2016
Workqueue: netns cleanup_net
0000000000000000 ffff880202417b90 ffffffff812b0013 ffff880202410ac0
ffffffff81870de8 ffff880202417bb8 ffffffff8107aee8 ffffffff81870de8
0000000000000c51 0000000000000000 ffff880202417be0 ffffffff8107b024
Call Trace:
[<ffffffff812b0013>] dump_stack+0x85/0xc2
[<ffffffff8107aee8>] ___might_sleep+0x148/0x240
[<ffffffff8107b024>] __might_sleep+0x44/0x80
[<ffffffff810b21bd>] synchronize_sched+0x2d/0xe0
[<ffffffff8109be6d>] ? trace_hardirqs_on+0xd/0x10
[<ffffffff8105c7bb>] ? __local_bh_enable_ip+0x6b/0xc0
[<ffffffff816a1b00>] ? _raw_spin_unlock_bh+0x30/0x40
[<ffffffff81667482>] __l2tp_session_unhash+0x172/0x220
[<ffffffff81667397>] ? __l2tp_session_unhash+0x87/0x220
[<ffffffff8166888b>] l2tp_tunnel_closeall+0x9b/0x140
[<ffffffff81668c74>] l2tp_tunnel_delete+0x14/0x60
[<ffffffff81668dd0>] l2tp_exit_net+0x110/0x270
[<ffffffff81668d5c>] ? l2tp_exit_net+0x9c/0x270
[<ffffffff815001c3>] ops_exit_list.isra.6+0x33/0x60
[<ffffffff81501166>] cleanup_net+0x1b6/0x280
...
This bug can easily be reproduced with a few steps:
$ sudo unshare -n bash # Create a shell in a new namespace
# ip link set lo up
# ip addr add 127.0.0.1 dev lo
# ip l2tp add tunnel remote 127.0.0.1 local 127.0.0.1 tunnel_id 1 \
peer_tunnel_id 1 udp_sport 50000 udp_dport 50000
# ip l2tp add session name foo tunnel_id 1 session_id 1 \
peer_session_id 1
# ip link set foo up
# exit # Exit the shell, in turn exiting the namespace
$ dmesg
...
[942121.089216] BUG: scheduling while atomic: kworker/u16:3/13872/0x00000200
...
To fix this, move the call to l2tp_tunnel_closeall() out of the RCU
critical section, and instead call it from l2tp_tunnel_del_work(), which
is running from the l2tp_wq workqueue.
Fixes: 2b551c6e7d ("l2tp: close sessions before initiating tunnel delete")
Signed-off-by: Ridge Kennedy <ridge.kennedy@alliedtelesis.co.nz>
Acked-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
udp_ioctl(), as its name suggests, is used by UDP protocols,
but is also used by L2TP :(
L2TP should use its own handler, because it really does not
look the same.
SIOCINQ for instance should not assume UDP checksum or headers.
Thanks to Andrey and syzkaller team for providing the report
and a nice reproducer.
While crashes only happen on recent kernels (after commit
7c13f97ffd ("udp: do fwd memory scheduling on dequeue")), this
probably needs to be backported to older kernels.
Fixes: 7c13f97ffd ("udp: do fwd memory scheduling on dequeue")
Fixes: 8558467201 ("udp: Fix udp_poll() and ioctl()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When same struct dst_entry can be used for many different
neighbours we can not use it for pending confirmations.
The datagram protocols can use MSG_CONFIRM to confirm the
neighbour. When used with MSG_PROBE we do not reach the
code where neighbour is confirmed, so we have to do the
same slow lookup by using the dst_confirm_neigh() helper.
When MSG_PROBE is not used, ip_append_data/ip6_append_data
will set the skb flag dst_pending_confirm.
Reported-by: YueHaibing <yuehaibing@huawei.com>
Fixes: 5110effee8 ("net: Do delayed neigh confirmation.")
Fixes: f2bb4bedf3 ("ipv4: Cache output routes in fib_info nexthops.")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split conditions, so that each test becomes clearer.
Also, for l2tp_ip, check if "laddr" is 0. This prevents a socket from
binding to the unspecified address when other sockets are already bound
using the same device (if any), connection ID and namespace.
Same thing for l2tp_ip6: add ipv6_addr_any(laddr) and
ipv6_addr_any(raddr) tests to ensure that an IPv6 unspecified address
passed as parameter is properly treated a wildcard.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
If "l2tp" was NULL, that'd mean "sk" is NULL too. This can't happen
since "sk" is returned by sk_for_each_bound().
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add const qualifier wherever possible for __l2tp_ip_bind_lookup() and
__l2tp_ip6_bind_lookup().
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
addr_len's value has already been verified at this point.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
For connected sockets, __l2tp_ip{,6}_bind_lookup() needs to check the
remote IP when looking for a matching socket. Otherwise a connected
socket can receive traffic not originating from its peer.
Drop l2tp_ip_bind_lookup() and l2tp_ip6_bind_lookup() instead of
updating their prototype, as these functions aren't used.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
An L2TP socket bound to the unspecified address should match with any
address. If not, it can't receive any packet and __l2tp_ip6_bind_lookup()
can't prevent another socket from binding on the same device/tunnel ID.
While there, rename the 'addr' variable to 'sk_laddr' (local addr), to
make following patch clearer.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the L2TP_MSG_* definitions to UAPI, as it is part of
the netlink API.
Signed-off-by: Asbjoern Sloth Toennesen <asbjorn@asbjorn.st>
Signed-off-by: David S. Miller <davem@davemloft.net>
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
The '!(addr && ipv6_addr_equal(addr, laddr))' part of the conditional
matches if addr is NULL or if addr != laddr.
But the intend of __l2tp_ip6_bind_lookup() is to find a sockets with
the same address, so the ipv6_addr_equal() condition needs to be
inverted.
For better clarity and consistency with the rest of the expression, the
(!X || X == Y) notation is used instead of !(X && X != Y).
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
When looking up an l2tp socket, we must consider a null netdevice id as
wild card. There are currently two problems caused by
__l2tp_ip_bind_lookup() not considering 'dif' as wild card when set to 0:
* A socket bound to a device (i.e. with sk->sk_bound_dev_if != 0)
never receives any packet. Since __l2tp_ip_bind_lookup() is called
with dif == 0 in l2tp_ip_recv(), sk->sk_bound_dev_if is always
different from 'dif' so the socket doesn't match.
* Two sockets, one bound to a device but not the other, can be bound
to the same address. If the first socket binding to the address is
the one that is also bound to a device, the second socket can bind
to the same address without __l2tp_ip_bind_lookup() noticing the
overlap.
To fix this issue, we need to consider that any null device index, be
it 'sk->sk_bound_dev_if' or 'dif', matches with any other value.
We also need to pass the input device index to __l2tp_ip_bind_lookup()
on reception so that sockets bound to a device never receive packets
from other devices.
This patch fixes l2tp_ip6 in the same way.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not enough to check for sockets bound to same address at the
beginning of l2tp_ip{,6}_bind(): even if no socket is found at that
time, a socket with the same address could be bound before we take
the l2tp lock again.
This patch moves the lookup right before inserting the new socket, so
that no change can ever happen to the list between address lookup and
socket insertion.
Care is taken to avoid side effects on the socket in case of failure.
That is, modifications of the socket are done after the lookup, when
binding is guaranteed to succeed, and before releasing the l2tp lock,
so that concurrent lookups will always see fully initialised sockets.
For l2tp_ip, 'ret' is set to -EINVAL before checking the SOCK_ZAPPED
bit. Error code was mistakenly set to -EADDRINUSE on error by commit
32c231164b ("l2tp: fix racy SOCK_ZAPPED flag check in l2tp_ip{,6}_bind()").
Using -EINVAL restores original behaviour.
For l2tp_ip6, the lookup is now always done with the correct bound
device. Before this patch, when binding to a link-local address, the
lookup was done with the original sk->sk_bound_dev_if, which was later
overwritten with addr->l2tp_scope_id. Lookup is now performed with the
final sk->sk_bound_dev_if value.
Finally, the (addr_len >= sizeof(struct sockaddr_in6)) check has been
dropped: addr is a sockaddr_l2tpip6 not sockaddr_in6 and addr_len has
already been checked at this point (this part of the code seems to have
been copy-pasted from net/ipv6/raw.c).
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Socket must be held while under the protection of the l2tp lock; there
is no guarantee that sk remains valid after the read_unlock_bh() call.
Same issue for l2tp_ip and l2tp_ip6.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Socket flags aren't updated atomically, so the socket must be locked
while reading the SOCK_ZAPPED flag.
This issue exists for both l2tp_ip and l2tp_ip6. For IPv6, this patch
also brings error handling for __ip6_datagram_connect() failures.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
udplite conflict is resolved by taking what 'net-next' did
which removed the backlog receive method assignment, since
it is no longer necessary.
Two entries were added to the non-priv ethtool operations
switch statement, one in 'net' and one in 'net-next, so
simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 7c6ae610a1, because l2tp_xmit_skb() never
returns NET_XMIT_CN, it ignores the return value of l2tp_xmit_core().
Cc: Gao Feng <gfree.wind@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
The tc could return NET_XMIT_CN as one congestion notification, but
it does not mean the packe is lost. Other modules like ipvlan,
macvlan, and others treat NET_XMIT_CN as success too.
So l2tp_eth_dev_xmit should add the NET_XMIT_CN check.
Signed-off-by: Gao Feng <gfree.wind@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dominik Heidler