Commit Graph

3297 Commits

Author SHA1 Message Date
Peter Rosin 649ac63a9a i2c: mux: mlxcpld: fix i2c mux selection caching
smbus functions return -ve on error, 0 on success.  However,
__i2c_transfer() have a different return signature - -ve on error, or
number of buffers transferred (which may be zero or greater).

The upshot of this is that the sense of the test is reversed when using
the mux on a bus supporting the master_xfer method: we cache the value
and never retry if we fail to transfer any buffers, but if we succeed,
we clear the cached value.

Fix this by making mlxcpld_mux_reg_write() return a -ve error code for
all failure cases, just as was done in commit 7f638c1cb0 ("i2c: mux:
pca954x: fix i2c mux selection caching").

This also aligns the implementations of these two muxes in this area.

Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-12-18 08:54:38 +01:00
Tin Huynh 8e598769c5 i2c: designware: fix wrong Tx/Rx FIFO for ACPI
ACPI always sets Tx/Rx FIFO to 32. This configuration will
cause problem if the IP core supports a FIFO size of less than 32.
The driver should read the FIFO size from the IP and select the smaller
one of the two.

Signed-off-by: Tin Huynh <tnhuynh@apm.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-12-17 19:38:03 +01:00
Tin Huynh 1635c5d04e i2c: xgene: Fix missing code of DTB support
In DTB case, i2c-core doesn't create slave device which is installed
on i2c-xgene bus because of missing code in this driver.
This patch fixes this issue.

Signed-off-by: Tin Huynh <tnhuynh@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-12-17 19:35:41 +01:00
Russell King 7f638c1cb0 i2c: mux: pca954x: fix i2c mux selection caching
smbus functions return -ve on error, 0 on success.  However,
__i2c_transfer() have a different return signature - -ve on error, or
number of buffers transferred (which may be zero or greater.)

The upshot of this is that the sense of the test is reversed when using
the mux on a bus supporting the master_xfer method: we cache the value
and never retry if we fail to transfer any buffers, but if we succeed,
we clear the cached value.

Fix this by making pca954x_reg_write() return a negative error code for
all failure cases.

Fixes: 463e8f845c ("i2c: mux: pca954x: retry updating the mux selection on failure")
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-12-17 19:29:44 +01:00
Jan Glauber 493ff7e2cd i2c: octeon: thunderx: Limit register access retries
Do not infinitely retry register readq and writeq operations
in order to not lock up the CPU in case the TWSI gets stuck.

Return -EIO in case of a failed data read. For all other
cases just return so subsequent operations will fail
and trigger the recovery.

Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-12-17 19:27:44 +01:00
Linus Torvalds 179a7ba680 This release has a few updates:
o STM can hook into the function tracer
  o Function filtering now supports more advance glob matching
  o Ftrace selftests updates and added tests
  o Softirq tag in traces now show only softirqs
  o ARM nop added to non traced locations at compile time
  o New trace_marker_raw file that allows for binary input
  o Optimizations to the ring buffer
  o Removal of kmap in trace_marker
  o Wakeup and irqsoff tracers now adhere to the set_graph_notrace file
  o Other various fixes and clean ups
 
 Note, there are two patches marked for stable. These were discovered
 near the end of the 4.9 rc release cycle. By the time I had them tested
 it was just a matter of days before 4.9 would be released, and I
 figured I would just submit them in the merge window. They are old
 bugs and not critical. Nothing non-root could abuse.
 -----BEGIN PGP SIGNATURE-----
 
 iQExBAABCAAbBQJYUrFHFBxyb3N0ZWR0QGdvb2RtaXMub3JnAAoJEMm5BfJq2Y3L
 2+AIAIr20kSQV/nA5htGAeCTobVk3WUxY6bvjd9mIJDKPP19akNLyREW0G3KnfCr
 yhx4aFRZG98fRu/6F8qieRosyN36lADDVYHelMFHMpcTOpE2aZGjaaOuNGxOEA9v
 FmMPTX+K3+dzKyFP4l68R3+5JuQ1/AqLTioTWeLW8IDQ2OOVsjD8+0BuXrNKMJDY
 o6U4Hk5U/vn+zHc6BmgBzloAXemBd7iJ1t5V3FRRGvm8yv3HU85Twc5ofGeYTWvB
 J8PboEywRlIzxg0Kd8mxnMI5PgaKZSEc2ub8E7cY/CZ5PYpDE2xDA2hJmJgfYp00
 1VW+DHRpRZfElsCcya6S6P4bs5Y=
 =MGZ/
 -----END PGP SIGNATURE-----

Merge tag 'trace-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace

Pull tracing updates from Steven Rostedt:
 "This release has a few updates:

   - STM can hook into the function tracer
   - Function filtering now supports more advance glob matching
   - Ftrace selftests updates and added tests
   - Softirq tag in traces now show only softirqs
   - ARM nop added to non traced locations at compile time
   - New trace_marker_raw file that allows for binary input
   - Optimizations to the ring buffer
   - Removal of kmap in trace_marker
   - Wakeup and irqsoff tracers now adhere to the set_graph_notrace file
   - Other various fixes and clean ups"

* tag 'trace-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (42 commits)
  selftests: ftrace: Shift down default message verbosity
  kprobes/trace: Fix kprobe selftest for newer gcc
  tracing/kprobes: Add a helper method to return number of probe hits
  tracing/rb: Init the CPU mask on allocation
  tracing: Use SOFTIRQ_OFFSET for softirq dectection for more accurate results
  tracing/fgraph: Have wakeup and irqsoff tracers ignore graph functions too
  fgraph: Handle a case where a tracer ignores set_graph_notrace
  tracing: Replace kmap with copy_from_user() in trace_marker writing
  ftrace/x86_32: Set ftrace_stub to weak to prevent gcc from using short jumps to it
  tracing: Allow benchmark to be enabled at early_initcall()
  tracing: Have system enable return error if one of the events fail
  tracing: Do not start benchmark on boot up
  tracing: Have the reg function allow to fail
  ring-buffer: Force rb_end_commit() and rb_set_commit_to_write() inline
  ring-buffer: Froce rb_update_write_stamp() to be inlined
  ring-buffer: Force inline of hotpath helper functions
  tracing: Make __buffer_unlock_commit() always_inline
  tracing: Make tracepoint_printk a static_key
  ring-buffer: Always inline rb_event_data()
  ring-buffer: Make rb_reserve_next_event() always inlined
  ...
2016-12-15 13:49:34 -08:00
Linus Torvalds 8600b697cd Merge branch 'i2c/for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:

 - the first series of making i2c_device_id optional instead of
   mandatory (in favor of alternatives like of_device_id).

   This involves adding a new probe callback (probe_new) which removes
   some peculiarities I2C had for a long time now. The new probe is
   matching the other subsystems now and the old one will be removed
   once all users are converted. It is expected to take a while but
   there is ongoing interest in that.

 - SMBus Host Notify introduced 4.9 got refactored. They are now using
   interrupts instead of the alert callback which solves multiple
   issues.

 - new drivers for iMX LowPower I2C, Mellanox CPLD and its I2C mux

 - significant refactoring for bcm2835 driver

 - the usual set of driver updates and improvements

* 'i2c/for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (46 commits)
  i2c: fsl-lpi2c: read lpi2c fifo size in probe()
  i2c: octeon: thunderx: Remove double-check after interrupt
  i2c: octeon: thunderx: TWSI software reset in recovery
  i2c: cadence: Allow Cadence I2C to be selected for Cadence Xtensa CPUs
  i2c: sh_mobile: Add per-Generation fallback bindings
  i2c: rcar: Add per-Generation fallback bindings
  i2c: imx-lpi2c: add low power i2c bus driver
  dt-bindings: i2c: imx-lpi2c: add devicetree bindings
  i2c: designware-pcidrv: Add 10bit address feature to medfield/merrifield
  i2c: pxa: Add support for the I2C units found in Armada 3700
  i2c: pxa: Add definition of fast and high speed modes via the regs layout
  dt-bindings: i2c: pxa: Update the documentation for the Armada 3700
  i2c: qup: support SMBus block read
  i2c: qup: add ACPI support
  i2c: designware: Consolidate default functionality bits
  i2c: i2c-mux-gpio: update mux with gpiod_set_array_value_cansleep
  i2c: mux: pca954x: Add ACPI support for pca954x
  i2c: use an IRQ to report Host Notify events, not alert
  i2c: i801: remove SMBNTFDDAT reads as they always seem to return 0
  i2c: i801: use the BIT() macro for FEATURES_* also
  ...
2016-12-15 12:56:35 -08:00
Gao Pan 6eb89ef029 i2c: fsl-lpi2c: read lpi2c fifo size in probe()
The lpi2c fifo size is a read only parameter resides Parameter
Register. It's better to read lpi2c tx/rx fifo size in probe()
other than just define a macro for it.

Signed-off-by: Gao Pan <pandy.gao@nxp.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-12-11 23:06:39 +01:00
Jan Glauber 38190dfb70 i2c: octeon: thunderx: Remove double-check after interrupt
Commit 1bb1ff3e7c ("i2c: octeon: Improve performance if interrupt is
early") added a double-check around the wait_event_timeout() condition.
The performance problem that this commit tried to work-around
could not be reproduced. It also makes the wait condition more
complicated then it should be. Therefore remove the double-check.

Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-12-11 22:59:10 +01:00
Jan Glauber ccee1a4cdc i2c: octeon: thunderx: TWSI software reset in recovery
I've seen i2c recovery reporting long loops of:

[ 1035.887818] i2c i2c-4: SCL is stuck low, exit recovery
[ 1037.999748] i2c i2c-4: SCL is stuck low, exit recovery
[ 1040.111694] i2c i2c-4: SCL is stuck low, exit recovery
...

Add a TWSI software reset which clears the status and
STA,STP,IFLG in SW_TWSI_EOP_TWSI_CTL.

With this the recovery works fine and above message is not seen.

Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-12-11 22:58:34 +01:00
Jan Kotas f8989783d7 i2c: cadence: Allow Cadence I2C to be selected for Cadence Xtensa CPUs
This patch allows Cadence I2C controller to be selected in systems using Cadence Xtensa processors.

Signed-off-by: Jan Kotas <jank@cadence.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-12-11 22:56:30 +01:00
Simon Horman b880ccaf17 i2c: sh_mobile: Add per-Generation fallback bindings
Add per-Generation fallback bindings for R-Car SoCs.

This is in keeping with the compatibility string scheme is being adopted
for drivers for Renesas SoCs.

Also, improve readability by listing the rmobile fallback compatibility
string after the more-specific compatibility strings they provide a
fallback for.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-12-11 22:52:28 +01:00
Simon Horman ad4a8dc3fe i2c: rcar: Add per-Generation fallback bindings
In the case of Renesas R-Car hardware we know that there are generations of
SoCs, e.g. Gen 2 and Gen 3. But beyond that it's not clear what the
relationship between IP blocks might be. For example, I believe that
r8a7790 is older than r8a7791 but that doesn't imply that the latter is a
descendant of the former or vice versa.

We can, however, by examining the documentation and behaviour of the
hardware at run-time observe that the current driver implementation appears
to be compatible with the IP blocks on SoCs within a given generation.

For the above reasons and convenience when enabling new SoCs a
per-generation fallback compatibility string scheme is being adopted for
drivers for Renesas SoCs.

Also:
* Deprecate renesas,i2c-rcar. It seems poorly named as it is only
  compatible with R-Car Gen 1. It also appears unused in mainline.
* Add some text to describe per-SoC bindings

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-12-11 22:48:53 +01:00
Steven Rostedt (Red Hat) 8cf868affd tracing: Have the reg function allow to fail
Some tracepoints have a registration function that gets enabled when the
tracepoint is enabled. There may be cases that the registraction function
must fail (for example, can't allocate enough memory). In this case, the
tracepoint should also fail to register, otherwise the user would not know
why the tracepoint is not working.

Cc: David Howells <dhowells@redhat.com>
Cc: Seiji Aguchi <seiji.aguchi@hds.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
2016-12-09 09:13:30 -05:00
Gao Pan a55fa9d0e4 i2c: imx-lpi2c: add low power i2c bus driver
This patch adds lpi2c bus driver to support new i.MX products
which use lpi2c instead of the old imx i2c.

The lpi2c can continue operating in stop mode when an appropriate
clock is available. It is also designed for low CPU overhead with
DMA offloading of FIFO register accesses.

Signed-off-by: Gao Pan <pandy.gao@nxp.com>
Reviewed-by: Fugang Duan <B38611@freescale.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-12-01 23:44:13 +01:00
Alexander Stein 531ccabbe4 i2c: designware-pcidrv: Add 10bit address feature to medfield/merrifield
Both Merrifield TRM and Medfield TRM state:
"Both 7-bit and 10-bit addressing modes are supported."

Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-12-01 23:38:43 +01:00
Romain Perier 294be03c62 i2c: pxa: Add support for the I2C units found in Armada 3700
The Armada 3700 has two I2C controllers that is compliant with the I2C
Bus Specificiation 2.1, supports multi-master and different bus speed:
Standard mode (up to 100 KHz), Fast mode (up to 400 KHz),
High speed mode (up to 3.4 Mhz).

This IP block has a lot of similarity with the PXA, except some register
offsets and bitfield. This commits adds a basic support for this I2C
unit.

Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-12-01 23:34:33 +01:00
Romain Perier 6c14bdacdb i2c: pxa: Add definition of fast and high speed modes via the regs layout
So far, the bit masks for the fast and high speed mode were statically
defined. Some IP blocks might use different bits for these modes.

This commit introduces new fields in order to enable the definition of
different bit masks for these features. If these fields are undefined,
ICR_FM and ICR_HS are selected to preserve backward compatibility with
other IPs.

Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-12-01 23:33:05 +01:00
Naveen Kaje cc9086e772 i2c: qup: support SMBus block read
I2C QUP driver relies on SMBus emulation support from the framework.
To handle SMBus block reads, the driver should check I2C_M_RECV_LEN
flag and should read the first byte received as the message length.

The driver configures the QUP hardware to read one byte. Once the
message length is known from this byte, the QUP hardware is configured
to read the rest.

Signed-off-by: Naveen Kaje <nkaje@codeaurora.org>
Signed-off-by: Austin Christ <austinwc@codeaurora.org>
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-29 22:43:38 +01:00
Naveen Kaje 515da74698 i2c: qup: add ACPI support
Add support to get the device parameters from ACPI. Assume
that the clocks are managed by firmware.

Signed-off-by: Naveen Kaje <nkaje@codeaurora.org>
Signed-off-by: Austin Christ <austinwc@codeaurora.org>
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-29 22:42:47 +01:00
Alexander Stein f06122f0bd i2c: designware: Consolidate default functionality bits
Use a common place for default functionality bits for both platform
and pci driver.

Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-29 20:19:56 +01:00
Peter Rosin feff5c0a27 i2c: i2c-mux-gpio: update mux with gpiod_set_array_value_cansleep
If the gpio controller supports it and the gpio lines are concentrated
to one gpio chip, the mux controller pins will get updated simultaneously.

Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-29 20:10:59 +01:00
tnhuynh@apm.com bbf9d262a1 i2c: mux: pca954x: Add ACPI support for pca954x
This patch enables ACPI support for mux-pca954x driver.

Signed-off-by: Tin Huynh <tnhuynh@apm.com>
Acked-by: Peter Rosin <peda@axentia.se>
[wsa: removed a trailing whitespace]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-29 20:06:47 +01:00
Jan Glauber dfa2ccc30e Revert "i2c: octeon: thunderx: Limit register access retries"
This reverts commit 70121f7f37 ("i2c: octeon: thunderx: Limit register access retries").
Using readq_poll_timeout instead of __raw_readq triggers the following
debug warning:

[   78.871568] ipmi_ssif: Trying hotmod-specified SSIF interface at i2c address 0x12, adapter Cavium ThunderX i2c adapter at 0000:01:09.4, slave address 0x0
[   78.886107] do not call blocking ops when !TASK_RUNNING; state=2 set at [<fffffc00080e0088>] prepare_to_wait_event+0x58/0x10c
[   78.897436] ------------[ cut here ]------------
[   78.902050] WARNING: CPU: 6 PID: 2235 at kernel/sched/core.c:7718 __might_sleep+0x80/0x88

[...]

[   79.133553] [<fffffc00080c3aac>] __might_sleep+0x80/0x88
[   79.138862] [<fffffc0000e30138>] octeon_i2c_test_iflg+0x4c/0xbc [i2c_thunderx]
[   79.146077] [<fffffc0000e30958>] octeon_i2c_test_ready+0x18/0x70 [i2c_thunderx]
[   79.153379] [<fffffc0000e30b04>] octeon_i2c_wait+0x154/0x1a4 [i2c_thunderx]
[   79.160334] [<fffffc0000e310bc>] octeon_i2c_xfer+0xf4/0xf60 [i2c_thunderx]

Signed-off-by: Jan Glauber <jglauber@cavium.com>
Acked-by: Steven J. Hill <steven.hill@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-29 20:04:21 +01:00
Jarkko Nikula 89119f0835 Revert "i2c: designware: do not disable adapter after transfer"
This reverts commit 0317e6c0f1.

Srinivas reported recently touchscreen and touchpad stopped working in
Haswell based machine in Linux 4.9-rc series with timeout errors from
i2c_designware:

[   16.508013] i2c_designware INT33C3:00: controller timed out
[   16.508302] i2c_hid i2c-MSFT0001:02: failed to change power setting.
[   17.532016] i2c_designware INT33C3:00: controller timed out
[   18.556022] i2c_designware INT33C3:00: controller timed out
[   18.556315] i2c_hid i2c-ATML1000:00: failed to retrieve report from device.

I managed to reproduce similar errors on another Haswell based machine
where touchscreen initialization fails maybe in every 1/5 - 1/2 boots.
Since root cause for these errors is not clear yet and debugging is
ongoing it's better to revert this commit as we are near to release.

Reported-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-25 23:23:25 +01:00
Benjamin Tissoires 4d5538f588 i2c: use an IRQ to report Host Notify events, not alert
The current SMBus Host Notify implementation relies on .alert() to
relay its notifications. However, the use cases where SMBus Host
Notify is needed currently is to signal data ready on touchpads.

This is closer to an IRQ than a custom API through .alert().
Given that the 2 touchpad manufacturers (Synaptics and Elan) that
use SMBus Host Notify don't put any data in the SMBus payload, the
concept actually matches one to one.

Benefits are multiple:
- simpler code and API: the client will just have an IRQ, and
  nothing needs to be added in the adapter beside internally
  enabling it.
- no more specific workqueue, the threading is handled by IRQ core
  directly (when required)
- no more races when removing the device (the drivers are already
  required to disable irq on remove)
- simpler handling for drivers: use plain regular IRQs
- no more dependency on i2c-smbus for i2c-i801 (and any other adapter)
- the IRQ domain is created automatically when the adapter exports
  the Host Notify capability
- the IRQ are assign only if ACPI, OF and the caller did not assign
  one already
- the domain is automatically destroyed on remove
- fewer lines of code (minus 20, yeah!)

Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-24 16:22:06 +01:00
Benjamin Tissoires c912a25a5a i2c: i801: remove SMBNTFDDAT reads as they always seem to return 0
On the platform tested, reading SMBNTFDDAT always returns 0 (using 1 read
of a word or 2 of 2 bytes). Given that we are not sure why and that we
don't need to rely on the data parameter in the current users of Host
Notify, remove this part of the code.

If someone wants to re-enable it, just revert this commit and data should
be available.

Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-24 16:22:05 +01:00
Benjamin Tissoires f91fba627c i2c: i801: use the BIT() macro for FEATURES_* also
no functional changes

Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-24 16:22:04 +01:00
Benjamin Tissoires fe9ba3ec1b i2c: i801: use BIT() macro for bits definition
i801 mixes hexadecimal and decimal values for defining bits. However,
we have a nice BIT() macro for this exact purpose.

No functional changes, cleanup only.

Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-24 16:22:03 +01:00
Benjamin Tissoires 9786b1f19e i2c: i801: minor formatting issues
No functional changes, just typos and remove unused #define.

Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-24 16:22:02 +01:00
Benjamin Tissoires 22e94bd677 i2c: i801: store and restore the SLVCMD register at load and unload
Also do not override any other configuration in this register.

Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-24 16:22:01 +01:00
Vadim Pasternak 6bec23bff9 i2c: mlxcpld: add master driver for mellanox systems
Device driver for Mellanox I2C controller logic, implemented in Lattice
CPLD device.
Device supports:
 - Master mode
 - One physical bus
 - Polling mode

The Kconfig currently controlling compilation of this code is:
drivers/i2c/busses/Kconfig:config I2C_MLXCPLD

Signed-off-by: Michael Shych <michaelsh@mellanox.com>
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-24 16:21:42 +01:00
Russell King 4d6d5f1d08 i2c: designware: fix rx fifo depth tracking
When loading the TX fifo to receive bytes on the I2C bus, we incorrectly
count the number of bytes:

	rx_limit = dev->rx_fifo_depth - dw_readl(dev, DW_IC_RXFLR);

	while (buf_len > 0 && tx_limit > 0 && rx_limit > 0) {
		if (rx_limit - dev->rx_outstanding <= 0)
			break;
		rx_limit--;
		dev->rx_outstanding++;
	}

DW_IC_RXFLR indicates how many bytes are available to be read in the
FIFO, dev->rx_fifo_depth is the FIFO size, and dev->rx_outstanding is
the number of bytes that we've requested to be read so far, but which
have not been read.

Firstly, increasing dev->rx_outstanding and decreasing rx_limit and then
comparing them results in each byte consuming "two" bytes in this
tracking, so this is obviously wrong.

Secondly, the number of bytes that _could_ be received into the FIFO at
any time is the number of bytes we have so far requested but not yet
read from the FIFO - in other words dev->rx_outstanding.

So, in order to request enough bytes to fill the RX FIFO, we need to
request dev->rx_fifo_depth - dev->rx_outstanding bytes.

Modifying the code thusly results in us reaching the maximum number of
bytes outstanding each time we queue more "receive" operations, provided
the transfer allows that to happen.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-24 16:18:15 +01:00
Russell King 2bf413d56b i2c: designware: report short transfers
Rather than reporting success for a short transfer due to interrupt
latency, report an error both to the caller, as well as to the kernel
log.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-24 16:17:34 +01:00
Alex Hemme ad092de60f i2c: i2c-mux-pca954x: fix deselect enabling for device-tree
Deselect functionality can be ignored for device-trees with
"i2c-mux-idle-disconnect" entries if no platform_data is available.
By enabling the deselect functionality outside the platform_data
block the logic works as it did in previous kernels.

Fixes: 7fcac98071 ("i2c: i2c-mux-pca954x: convert to use an explicit i2c mux core")
Cc: <stable@vger.kernel.org> # v4.7+
Signed-off-by: Alex Hemme <ahemme@cisco.com>
Signed-off-by: Ziyang Wu <ziywu@cisco.com>
[touched up a few minor issues /peda]
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-19 21:49:29 +01:00
Tanmay Jagdale 254df038e5 i2c: xlp9xx: ACPI support for I2C clients
The ACPI companion of the adapter has to be set for I2C controller
code to read and attach the slave devices described in the ACPI table
with the I2CSerialBus resource descriptor. Used ACPI_COMPANION_SET
macro to set this.

Signed-off-by: Tanmay Jagdale <tanmay.jagdale@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-18 02:25:38 +01:00
Masahiro Yamada b92b7dbc71 i2c: uniphier-f: rename jump label to follow coding style guideline
Documentation/CodingStyle recommends to use label names which say
what the goto does or why the goto exists.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-18 02:16:08 +01:00
Masahiro Yamada a837bad6f2 i2c: uniphier: rename jump label to follow coding style guideline
Documentation/CodingStyle recommends to use label names which say
what the goto does or why the goto exists.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-18 02:13:11 +01:00
Jarkko Nikula 973652db6f i2c: designware: Allow reduce bus speed by "clock-frequency" property
Allow more flexibility to bus speed selection. Now if there are I2C
slave connections defined in ACPI the speed of slowest device on the bus
will define the bus speed. However if also "clock-frequency" device
property is defined we should use the slowest of these two.

This is targeted to maker boards where developer may want to connect
slower I2C slave devices to the bus than defined in existing ACPI I2C
slave connections.

Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-18 02:08:03 +01:00
Tin Huynh c3ae106050 i2c: designware: Implement support for SMBus block read and write
Free and Open IPMI use SMBUS BLOCK Read/Write to support SSIF protocol.
However, I2C Designware Core Driver doesn't handle the case at the moment.
The below patch supports this feature.

Signed-off-by: Tin Huynh <tnhuynh@apm.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-18 02:06:41 +01:00
Julia Lawall 379883cc67 i2c: constify i2c_adapter_quirks structures
Check for i2c_adapter_quirks structures that are only stored in the
quirks field of an i2c_adapter structure.  This field is declared
const, so i2c_adapter_quirks structures that have this property can be
declared as const also.

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ray Jui <ray.jui@broadcom.com> # for bcm-iproc
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-18 02:05:03 +01:00
Wei Yongjun 68d85d0e03 i2c: digicolor: use clk_disable_unprepare instead of clk_unprepare
since clk_prepare_enable() is used to get i2c->clk, we should
use clk_disable_unprepare() to release it for the error path.

Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-18 01:48:01 +01:00
Paul Gortmaker ff3a98be79 i2c: i2c-pxa-pci; make explicitly non-modular
The Kconfig currently controlling compilation of this code is:

drivers/i2c/busses/Kconfig:config I2C_PXA_PCI
drivers/i2c/busses/Kconfig:     def_bool I2C_PXA && X86_32 && PCI && OF

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.

Since module_pci_driver() uses the same init level priority as
builtin_pci_driver() the init ordering remains unchanged with
this commit.

Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-18 01:44:38 +01:00
Vadim Pasternak c02b7bf532 i2c: mux: mellanox: add driver
This driver allows I2C routing controlled through CPLD select registers on
a wide range of Mellanox systems (CPLD Lattice device).
MUX selection is provided by digital and analog HW. Analog part is not
under SW control.
Digital part is under CPLD control (channel selection/de-selection).

Connectivity schema.
.---.             .-------------.
| l |             |             |-- i2cx1 -- i2cx8
| i |-- i2cn --+--| mlxcpld mux |
| n |          |  |             |-- i2cy1 -- i2cy8
| u |          |  '-------------'
| x |          |         |
'---'          '---------'

i2c-mux-mlxpcld does not necessarily require i2c-mlxcpld. It can be used
along with another bus driver, and still control i2c routing through CPLD
mux selection, in case the system is equipped with CPLD capable of mux
selection control.

The Kconfig currently controlling compilation of this code is:
drivers/i2c/muxes/Kconfig:config I2C_MUX_MLXCPLD

Signed-off-by: Michael Shych <michaelsh@mellanox.com>
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-17 23:19:00 +01:00
Lee Jones b8a1a4cd5a i2c: Provide a temporary .probe_new() call-back type
This will aid the seamless removal of the current probe()'s, more
commonly unused than used second parameter.  Most I2C drivers can
simply switch over to the new interface, others which have DT
support can use its own matching instead and others can call
i2c_match_id() themselves.  This brings I2C's device probe method
into line with other similar interfaces in the kernel and prevents
the requirement to pass an i2c_device_id table.

Suggested-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[Kieran: fix rebase conflicts and adapt for dev_pm_domain_{attach,detach}]
Tested-by: Kieran Bingham <kieran@bingham.xyz>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kieran Bingham <kieran@bingham.xyz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-17 16:10:23 +01:00
Lee Jones 5f441fcaa3 i2c: Export i2c_match_id() for direct use by device drivers
When there was no other way to match a I2C device to driver i2c_match_id()
was exclusively used.  However, now there are other types of tables which
are commonly supplied, matching on an i2c_device_id table is used less
frequently.  Instead of _always_ calling i2c_match_id() from within the
framework, we only need to do so from drivers which have no other way of
matching.  This patch makes i2c_match_id() available to the aforementioned
device drivers.

Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Kieran Bingham <kieran@bingham.xyz>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kieran Bingham <kieran@bingham.xyz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-17 16:10:22 +01:00
Lee Jones da10c06a04 i2c: Make I2C ID tables non-mandatory for DT'ed devices
Currently the I2C framework insists on devices supplying an I2C ID
table.  Many of the devices which do so unnecessarily adding quite a
few wasted lines to kernel code.  This patch allows drivers a means
to 'not' supply the aforementioned table and match on DT match tables
instead.

Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Kieran Bingham <kieran@bingham.xyz>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kieran Bingham <kieran@bingham.xyz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-17 16:10:21 +01:00
Lee Jones 298d4de1ed i2c: Match using traditional OF methods, then by vendor-less compatible strings
This function provides a single call for all I2C devices which need to
match firstly using traditional OF means i.e by of_node, then if that
fails we attempt to match using the supplied I2C client name with a
list of supplied compatible strings with the '<vendor>,' string
removed.  The latter is required due to the unruly naming conventions
used currently by I2C devices.

Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[Kieran: Fix static inline usage on !CONFIG_OF]
Tested-by: Kieran Bingham <kieran@bingham.xyz>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kieran Bingham <kieran@bingham.xyz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-17 16:10:20 +01:00
Lee Jones cabcf4f6be i2c: Add the ability to match device to compatible string without an of_node
A great deal of I2C devices are currently matched via DT node name, and
as such the compatible naming convention of '<vendor>,<device>' has gone
somewhat awry - some nodes don't supply one, some supply an arbitrary
string and others the correct device name with an arbitrary vendor prefix.

In an effort to correct this problem we have to supply a mechanism to
match a device by compatible string AND by simple device name.  This
function strips off the '<vendor>,' part of a supplied compatible string
and attempts to match without it.

It is also used for sysfs, where a user can choose to instantiate a
device on an i2c bus using the sysfs interface by providing a string and
address to match and communicate with the device on the bus. Presently
this string is only matched against the old i2c device id style strings,
even in the presence of full device tree compatible strings with vendor
prefixes.

Providing a vendor-prefixed string to the sysfs interface will not match
against the device tree of_match_device() calls as there is no device
tree node to parse from the sysfs interface.

This function can match both vendor prefixed and stripped compatible
strings on the sysfs interface.

Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kieran Bingham <kieran@bingham.xyz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-17 16:07:26 +01:00
Linus Walleij 93d710a65e i2c: mux: fix up dependencies
We get the following build error from UM Linux after adding
an entry to drivers/iio/gyro/Kconfig that issues "select I2C_MUX":

ERROR: "devm_ioremap_resource"
   [drivers/i2c/muxes/i2c-mux-reg.ko] undefined!
ERROR: "of_address_to_resource"
   [drivers/i2c/muxes/i2c-mux-reg.ko] undefined!

It appears that the I2C mux core code depends on HAS_IOMEM
for historical reasons, while CONFIG_I2C_MUX_REG does *not*
have a direct dependency on HAS_IOMEM.

This creates a situation where a allyesconfig or allmodconfig
for UM Linux will select I2C_MUX, and will implicitly enable
I2C_MUX_REG as well, and the compilation will fail for the
register driver.

Fix this up by making I2C_MUX_REG depend on HAS_IOMEM and
removing the dependency from I2C_MUX.

Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reported-by: Jonathan Cameron <jic23@jic23.retrosnub.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
2016-11-14 18:23:30 +01:00
Lee Jones 811073b11b i2c: Add pointer dereference protection to i2c_match_id()
Here we're providing dereference protection for i2c_match_id(), which
saves us having to do it each time it's called.  We're also stripping
out the (now) needless checks in i2c_device_match().  This patch paves
the way for other, similar code trimming.

Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Kieran Bingham <kieran@bingham.xyz>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kieran Bingham <kieran@bingham.xyz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-13 19:08:01 +01:00
Wolfram Sang d052db11c1 i2c: mux: demux-pinctrl: make drivers with no pinctrl work again
Some drivers like i2c-gpio do not have dedicated pinctrl states. They
broke when error checking for pinctrl was added. Detect them now, and in
their case, simply skip over pinctrl configuration.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-10 21:12:47 +01:00
Noralf Trønnes 9446f62e8e i2c: bcm2835: Add support for dynamic clock
Support a dynamic clock by reading the frequency and setting the
divisor in the transfer function instead of during probe.

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-07 01:48:32 +01:00
Noralf Trønnes e13e19e12f i2c: bcm2835: Support i2c-dev ioctl I2C_TIMEOUT
Use i2c_adapter->timeout for the completion timeout value. The core
default is 1 second.

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-07 01:48:32 +01:00
Noralf Trønnes ee05fea21b i2c: bcm2835: Add support for Repeated Start Condition
Documentation/i2c/i2c-protocol states that Combined transactions should
separate messages with a Start bit and end the whole transaction with a
Stop bit. This patch adds support for issuing only a Start between
messages instead of a Stop followed by a Start.

This implementation differs from downstream i2c-bcm2708 in 2 respects:
- it uses an interrupt to detect that the transfer is active instead
  of using polling. There is no interrupt for Transfer Active, but by
  not prefilling the FIFO it's possible to use the TXW interrupt.
- when resetting/disabling the controller between transfers it writes
  CLEAR to the control register instead of just zero.
  Using just zero gave many errors. This might be the reason why
  downstream had to disable this feature and make it available with a
  module parameter.

I have run thousands of transfers to a DS1307 (rtc), MMA8451 (accel)
and AT24C32 (eeprom) in parallel without problems.

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-07 01:48:32 +01:00
Noralf Trønnes 8d2cc5cc6e i2c: bcm2835: Can't support I2C_M_IGNORE_NAK
The controller can't support this flag, so remove it.

Documentation/i2c/i2c-protocol states that all of the message is sent:

I2C_M_IGNORE_NAK:
    Normally message is interrupted immediately if there is [NA] from the
    client. Setting this flag treats any [NA] as [A], and all of
    message is sent.

>From the BCM2835 ARM Peripherals datasheet:

    The ERR field is set when the slave fails to acknowledge either
    its address or a data byte written to it.

So when the controller doesn't receive an ack, it sets ERR and raises
an interrupt. In other words, the whole message is not sent.

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-07 01:48:31 +01:00
Noralf Trønnes 23c9540b3a i2c: bcm2835: Use dev_dbg logging on transfer errors
Writing to an AT24C32 generates on average 2x i2c transfer errors per
32-byte page write. Which amounts to a lot for a 4k write. This is due
to the fact that the chip doesn't respond during it's internal write
cycle when the at24 driver tries and retries the next write.
Only a handful drivers use dev_err() on transfer error, so switch to
dev_dbg() instead.

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-07 01:48:31 +01:00
Noralf Trønnes d4030d75c7 i2c: bcm2835: Protect against unexpected TXW/RXR interrupts
If an unexpected TXW or RXR interrupt occurs (msg_buf_remaining == 0),
the driver has no way to fill/drain the FIFO to stop the interrupts.
In this case the controller has to be disabled and the transfer
completed to avoid hang.

(CLKT | ERR) and DONE interrupts are completed in their own paths, and
the controller is disabled in the transfer function after completion.
Unite the code paths and do disabling inside the interrupt routine.

Clear interrupt status bits in the united completion path instead of
trying to do it on every interrupt which isn't necessary.
Only CLKT, ERR and DONE can be cleared that way.

Add the status value to the error value in case of TXW/RXR errors to
distinguish them from the other S_LEN error.

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-07 01:48:31 +01:00
Noralf Trønnes e247454103 i2c: bcm2835: Fix hang for writing messages larger than 16 bytes
Writing messages larger than the FIFO size results in a hang, rendering
the machine unusable. This is because the RXD status flag is set on the
first interrupt which results in bcm2835_drain_rxfifo() stealing bytes
from the buffer. The controller continues to trigger interrupts waiting
for the missing bytes, but bcm2835_fill_txfifo() has none to give.
In this situation wait_for_completion_timeout() apparently is unable to
stop the madness.

The BCM2835 ARM Peripherals datasheet has this to say about the flags:
  TXD: is set when the FIFO has space for at least one byte of data.
  RXD: is set when the FIFO contains at least one byte of data.
  TXW: is set during a write transfer and the FIFO is less than full.
  RXR: is set during a read transfer and the FIFO is or more full.

Implementing the logic from the downstream i2c-bcm2708 driver solved
the hang problem.

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-11-07 01:48:31 +01:00
Vladimir Zapolskiy 147b36d5b7 i2c: core: fix NULL pointer dereference under race condition
Race condition between registering an I2C device driver and
deregistering an I2C adapter device which is assumed to manage that
I2C device may lead to a NULL pointer dereference due to the
uninitialized list head of driver clients.

The root cause of the issue is that the I2C bus may know about the
registered device driver and thus it is matched by bus_for_each_drv(),
but the list of clients is not initialized and commonly it is NULL,
because I2C device drivers define struct i2c_driver as static and
clients field is expected to be initialized by I2C core:

  i2c_register_driver()             i2c_del_adapter()
    driver_register()                 ...
      bus_add_driver()                ...
        ...                           bus_for_each_drv(..., __process_removed_adapter)
      ...                               i2c_do_del_adapter()
    ...                                   list_for_each_entry_safe(..., &driver->clients, ...)
    INIT_LIST_HEAD(&driver->clients);

To solve the problem it is sufficient to do clients list head
initialization before calling driver_register().

The problem was found while using an I2C device driver with a sluggish
registration routine on a bus provided by a physically detachable I2C
master controller, but practically the oops may be reproduced under
the race between arbitraty I2C device driver registration and managing
I2C bus device removal e.g. by unbinding the latter over sysfs:

% echo 21a4000.i2c > /sys/bus/platform/drivers/imx-i2c/unbind
  Unable to handle kernel NULL pointer dereference at virtual address 00000000
  Internal error: Oops: 17 [#1] SMP ARM
  CPU: 2 PID: 533 Comm: sh Not tainted 4.9.0-rc3+ #61
  Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
  task: e5ada400 task.stack: e4936000
  PC is at i2c_do_del_adapter+0x20/0xcc
  LR is at __process_removed_adapter+0x14/0x1c
  Flags: NzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
  Control: 10c5387d  Table: 35bd004a  DAC: 00000051
  Process sh (pid: 533, stack limit = 0xe4936210)
  Stack: (0xe4937d28 to 0xe4938000)
  Backtrace:
  [<c0667be0>] (i2c_do_del_adapter) from [<c0667cc0>] (__process_removed_adapter+0x14/0x1c)
  [<c0667cac>] (__process_removed_adapter) from [<c0516998>] (bus_for_each_drv+0x6c/0xa0)
  [<c051692c>] (bus_for_each_drv) from [<c06685ec>] (i2c_del_adapter+0xbc/0x284)
  [<c0668530>] (i2c_del_adapter) from [<bf0110ec>] (i2c_imx_remove+0x44/0x164 [i2c_imx])
  [<bf0110a8>] (i2c_imx_remove [i2c_imx]) from [<c051a838>] (platform_drv_remove+0x2c/0x44)
  [<c051a80c>] (platform_drv_remove) from [<c05183d8>] (__device_release_driver+0x90/0x12c)
  [<c0518348>] (__device_release_driver) from [<c051849c>] (device_release_driver+0x28/0x34)
  [<c0518474>] (device_release_driver) from [<c0517150>] (unbind_store+0x80/0x104)
  [<c05170d0>] (unbind_store) from [<c0516520>] (drv_attr_store+0x28/0x34)
  [<c05164f8>] (drv_attr_store) from [<c0298acc>] (sysfs_kf_write+0x50/0x54)
  [<c0298a7c>] (sysfs_kf_write) from [<c029801c>] (kernfs_fop_write+0x100/0x214)
  [<c0297f1c>] (kernfs_fop_write) from [<c0220130>] (__vfs_write+0x34/0x120)
  [<c02200fc>] (__vfs_write) from [<c0221088>] (vfs_write+0xa8/0x170)
  [<c0220fe0>] (vfs_write) from [<c0221e74>] (SyS_write+0x4c/0xa8)
  [<c0221e28>] (SyS_write) from [<c0108a20>] (ret_fast_syscall+0x0/0x1c)

Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
2016-11-04 20:36:58 +01:00
Stefan Agner 533169d164 i2c: imx: defer probe if bus recovery GPIOs are not ready
Some SoC might load the GPIO driver after the I2C driver and
using the I2C bus recovery mechanism via GPIOs. In this case
it is crucial to defer probing if the GPIO request functions
do so, otherwise the I2C driver gets loaded without recovery
mechanisms enabled.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
2016-10-25 12:15:00 +02:00
Jarkko Nikula 171e23e150 i2c: designware: Avoid aborted transfers with fast reacting I2C slaves
I2C DesignWare may abort transfer with arbitration lost if I2C slave pulls
SDA down quickly after falling edge of SCL. Reason for this is unknown but
after trial and error it was found this can be avoided by enabling non-zero
SDA RX hold time for the receiver.

By the specification SDA RX hold time extends incoming SDA low to high
transition by n * ic_clk cycles but only when SCL is high. However it
seems to help avoid above faulty arbitration lost error.

Bits 23:16 in IC_SDA_HOLD register define the SDA RX hold time for the
receiver. Be conservative and enable 1 ic_clk cycle long hold time in
case boot firmware hasn't set it up.

Reported-by: Jukka Laitinen <jukka.laitinen@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jukka Laitinen <jukka.laitinen@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-10-25 12:09:09 +02:00
Jean Delvare ba9ad2af70 i2c: i801: Fix I2C Block Read on 8-Series/C220 and later
Starting with the 8-Series/C220 PCH (Lynx Point), the SMBus
controller includes a SPD EEPROM protection mechanism. Once the SPD
Write Disable bit is set, only reads are allowed to slave addresses
0x50-0x57.

However the legacy implementation of I2C Block Read since the ICH5
looks like a write, and is therefore blocked by the SPD protection
mechanism. This causes the eeprom and at24 drivers to fail.

So assume that I2C Block Read is implemented as an actual read on
these chipsets. I tested it on my Q87 chipset and it seems to work
just fine.

Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
[wsa: rebased to v4.9-rc2]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-10-25 12:00:01 +02:00
Hoan Tran 603616017c i2c: xgene: Avoid dma_buffer overrun
SMBus block command uses the first byte of buffer for the data length.
The dma_buffer should be increased by 1 to avoid the overrun issue.

Reported-by: Phil Endecott <phil_gjouf_endecott@chezphil.org>
Signed-off-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
2016-10-25 11:50:52 +02:00
Javier Martinez Canillas 60a951af8e i2c: digicolor: Fix module autoload
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.

Export the module alias information using the MODULE_DEVICE_TABLE() macro.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-10-25 11:49:01 +02:00
Javier Martinez Canillas 2cb496db3d i2c: xlr: Fix module autoload for OF registration
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.

Export the module alias information using the MODULE_DEVICE_TABLE() macro.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-10-25 11:49:00 +02:00
Javier Martinez Canillas 06e7b10a87 i2c: xlp9xx: Fix module autoload
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.

Export the module alias information using the MODULE_DEVICE_TABLE() macro.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-10-25 11:48:59 +02:00
Javier Martinez Canillas 3855ada848 i2c: jz4780: Fix module autoload
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.

Export the module alias information using the MODULE_DEVICE_TABLE() macro.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-10-25 11:48:58 +02:00
Greg Ungerer 17791650c3 i2c: allow configuration of imx driver for ColdFire architecture
The i2c controller used by Freescales iMX processors is the same
hardware module used on Freescales ColdFire family of processors.

We can use the existing i2c-imx driver on ColdFire family members.
Modify the configuration to allow it to be selected when compiling
for ColdFire targets.

Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-10-25 11:48:57 +02:00
Ralf Ramsauer 6a676fb69d i2c: mark device nodes only in case of successful instantiation
Instantiated I2C device nodes are marked with OF_POPULATE. This was
introduced in 4f001fd301. On unloading, loaded device nodes will of
course be unmarked. The problem are nodes that fail during
initialisation: If a node fails, it won't be unloaded and hence not be
unmarked.

If a I2C driver module is unloaded and reloaded, it will skip nodes that
failed before.

Skip device nodes that are already populated and mark them only in case
of success.

Fixes: 4f001fd301 ("i2c: Mark instantiated device nodes with OF_POPULATE")
Signed-off-by: Ralf Ramsauer <ralf@ramses-pyramidenbau.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
[wsa: use 14-digit commit sha]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
2016-10-25 11:48:48 +02:00
David Wu 399c168ab5 i2c: rk3x: Give the tuning value 0 during rk3x_i2c_v0_calc_timings
We found a bug that i2c transfer sometimes failed on 3066a board with
stabel-4.8, the con register would be updated by uninitialized tuning
value, it made the i2c transfer failed.

So give the tuning value to be zero during rk3x_i2c_v0_calc_timings.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
2016-10-25 11:11:46 +02:00
Ruqiang Ju ae824f0024 i2c: hix5hd2: allow build with ARCH_HISI
This driver should be buildable with ARCH_HISI,
because some of other HiSilicon SoCs also use it.

Signed-off-by: Ruqiang Ju <juruqiang@huawei.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-10-25 11:09:16 +02:00
Wolfram Sang b2edcdae3d i2c: 'i2c-bus' node support for v4.8-rc1
This includes the device tree binding and I2C core changes to support
 the i2c-bus subnode that I2C masters can use to describe their slaves
 in a separate namespace and therefore avoid clashing with potentially
 other subnodes.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iQIcBAABCAAGBQJXdn2gAAoJEN0jrNd/PrOhe94P/j+1I3iGpHcU/mNmCaqgit9z
 TLMehmgglf9kj0iXpYoBjYU/XxzRKBfOaceRrPj16V9GbhiKGcHX0fhH06zydczS
 ZPS5FBNGqH9C6WYe8oszTBWz5skulSQba6VUwG01MnT2Nv7z7ONcHB2HPjM6TKob
 D0dxN4U3BlfTCGd/FxJariork2xY8o8mKZN7pntkJ+hQNeengCXXoPaY2bGSFH4K
 omfUal8/tdPZAruMaA/Dmvu9jBv0RkVSQzNnHXNkGzAw3fAsYm1UzcpG4VNhgeyj
 XNFiedIFOls8KW2Xd0LdPAzpyafS4w4gBj2SOol0xpUFhA9CchZCzci7DI2NSj9A
 VpiZzBPt6I+zv9c2HdzRqjH2PZTRoy0c9/szCBWyabZ/tST3SWk/tBY5SoLYpmL7
 Jq/sOWtegpGvj2XRw8jhmxXVjXYzqzAbyo6SrINZs8ElFrWZxTgsVHmq2SVE5qvh
 DnIpr7y/gfKyqAynm0QshNCo5kauvSX4Pa55MfEB/7GfkqhvYzjg+nlplut9woSG
 +JN3dWS5tts9pqzHWVL4YY/S11Dx+pT6ZPkmprjMAN+ghxNWjEhA57q7FxAHTU83
 BsermHINCpCcN/zyLGDXSaJbJq9hH5LLCHA23ZfnWtOFC5zikp1TG325A/2WMnwb
 ovKSLXRScyVqliffmO8G
 =+0Q/
 -----END PGP SIGNATURE-----

Merge tag 'tegra-for-4.8-i2c' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into i2c/for-next

[wsa: fell through the cracks, applied to 4.9 now]

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

i2c: 'i2c-bus' node support for v4.8-rc1

This includes the device tree binding and I2C core changes to support
the i2c-bus subnode that I2C masters can use to describe their slaves
in a separate namespace and therefore avoid clashing with potentially
other subnodes.
2016-10-11 23:37:26 +02:00
Linus Torvalds 87840a2b7e Merge branch 'i2c/for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
 "Here is the 4.9 pull request from I2C including:

   - centralized error messages when registering to the core
   - improved lockdep annotations to prevent false positives
   - DT support for muxes, gates, and arbitrators
   - bus speeds can now be obtained from ACPI
   - i2c-octeon got refactored and now supports ThunderX SoCs, too
   - i2c-tegra and i2c-designware got a bigger bunch of updates
   - a couple of standard driver fixes and improvements"

* 'i2c/for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (71 commits)
  i2c: axxia: disable clks in case of failure in probe
  i2c: octeon: thunderx: Limit register access retries
  i2c: uniphier-f: fix misdetection of incomplete STOP condition
  gpio: pca953x: variable 'id' was used twice
  i2c: i801: Add support for Kaby Lake PCH-H
  gpio: pca953x: fix an incorrect lockdep warning
  i2c: add a warning to i2c_adapter_depth()
  lockdep: make MAX_LOCKDEP_SUBCLASSES unconditionally visible
  i2c: export i2c_adapter_depth()
  i2c: rk3x: Fix variable 'min_total_ns' unused warning
  i2c: rk3x: Fix sparse warning
  i2c / ACPI: Do not touch an I2C device if it belongs to another adapter
  i2c: octeon: Fix high-level controller status check
  i2c: octeon: Avoid sending STOP during recovery
  i2c: octeon: Fix set SCL recovery function
  i2c: rcar: add support for r8a7796 (R-Car M3-W)
  i2c: imx: make bus recovery through pinctrl optional
  i2c: meson: add gxbb compatible string
  i2c: uniphier-f: set the adapter to master mode when probing
  i2c: uniphier-f: avoid WARN_ON() of clk_disable() in failure path
  ...
2016-10-07 14:12:21 -07:00
Rafael J. Wysocki 0137a337d7 Merge branches 'acpi-wdat' and 'acpi-ec'
* acpi-wdat:
  watchdog: wdat_wdt: Fix warning for using 0 as NULL
  watchdog: wdat_wdt: fix return value check in wdat_wdt_probe()
  platform/x86: intel_pmc_ipc: Do not create iTCO watchdog when WDAT table exists
  i2c: i801: Do not create iTCO watchdog when WDAT table exists
  mfd: lpc_ich: Do not create iTCO watchdog when WDAT table exists
  ACPI / watchdog: Add support for WDAT hardware watchdog

* acpi-ec:
  ACPI / EC: Fix issues related to boot_ec
  ACPI / EC: Fix a gap that ECDT EC cannot handle EC events
  ACPI / EC: Fix a memory leakage issue in acpi_ec_add()
  ACPI / EC: Cleanup first_ec/boot_ec code
  ACPI / EC: Enable event freeze mode to improve event handling for suspend process
  ACPI / EC: Add PM operations to improve event handling for suspend process
  ACPI / EC: Add PM operations to improve event handling for resume process
  ACPI / EC: Fix an issue that SCI_EVT cannot be detected after event is enabled
  ACPI / EC: Add EC_FLAGS_QUERY_ENABLED to reveal a hidden logic
  ACPI / EC: Add PM operations for suspend/resume noirq stage
2016-10-02 01:40:07 +02:00
Mika Westerberg 1f6dbb022b i2c: i801: Do not create iTCO watchdog when WDAT table exists
ACPI WDAT table is the preferred way to use hardware watchdog over the
native iTCO_wdt. Windows only uses this table for its hardware watchdog
implementation so we should be relatively safe to trust it has been
validated by OEMs

Prevent iTCO watchdog creation if we detect that there is ACPI WDAT table.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2016-09-28 23:08:08 +02:00
Alexey Khoroshilov 662786a542 i2c: axxia: disable clks in case of failure in probe
axxia_i2c_probe() does not disable clock in case of failure
in i2c_add_adapter(). Also it ignores returned value from
clk_prepare_enable().

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-09-24 11:26:55 +02:00
Jan Glauber 70121f7f37 i2c: octeon: thunderx: Limit register access retries
Do not infinitely retry register readq and writeq operations
in order to not lock up the CPU in case the TWSI gets stuck.

Return -ETIMEDOUT in case of a failed data read. For all other
cases just return so subsequent operations will fail.

Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-09-24 11:22:24 +02:00
Masahiro Yamada fcbd4bddb3 i2c: uniphier-f: fix misdetection of incomplete STOP condition
Currently, the status register FI2C_SR is checked immediately after
a STOP condition is issued in case of the deferred STOP condition.
It takes typically 5-10 usec until the corresponding bits in the
register are set, so the error check for "stop condition was not
completed" is very likely to be false positive.

Add wait code to relax the status register check.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-09-24 11:19:15 +02:00
Andy Shevchenko 31158763ef i2c: i801: Add support for Kaby Lake PCH-H
Intel Kaby Lake PCH-H has the same legacy SMBus host controller than Intel
Sunrisepoint PCH. It also has same iTCO watchdog on the bus.

Add Kaby Lake PCH-H PCI ID to the list of supported devices.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-09-24 10:57:56 +02:00
Bartosz Golaszewski 2771dc34dd i2c: add a warning to i2c_adapter_depth()
This routine is only used together with lockdep for nested locking.
The number of lock subclasses is limited to 8 as defined in lockdep.h

Emit a warning if the adapter depth exceeds the maximum number of
lockdep subclasses.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Peter Rosin <peda@axentia.se>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-09-24 10:50:00 +02:00
Bartosz Golaszewski 8dd1fe1594 i2c: export i2c_adapter_depth()
For crazy setups in which an i2c gpio expander is behind an i2c gpio
multiplexer controlled by a gpio provided a second expander using the
same device driver we need to explicitly tell lockdep how to handle
nested locking.

Export i2c_adapter_depth() as public API to be reused outside of i2c
core code.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Peter Rosin <peda@axentia.se>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-09-24 10:48:18 +02:00
Sudeep Holla 331dcf421c i2c: qup: skip qup_i2c_suspend if the device is already runtime suspended
If the i2c device is already runtime suspended, if qup_i2c_suspend is
executed during suspend-to-idle or suspend-to-ram it will result in the
following splat:

WARNING: CPU: 3 PID: 1593 at drivers/clk/clk.c:476 clk_core_unprepare+0x80/0x90
Modules linked in:

CPU: 3 PID: 1593 Comm: bash Tainted: G        W       4.8.0-rc3 #14
Hardware name: Qualcomm Technologies, Inc. APQ 8016 SBC (DT)
PC is at clk_core_unprepare+0x80/0x90
LR is at clk_unprepare+0x28/0x40
pc : [<ffff0000086eecf0>] lr : [<ffff0000086f0c58>] pstate: 60000145
Call trace:
 clk_core_unprepare+0x80/0x90
 qup_i2c_disable_clocks+0x2c/0x68
 qup_i2c_suspend+0x10/0x20
 platform_pm_suspend+0x24/0x68
 ...

This patch fixes the issue by executing qup_i2c_pm_suspend_runtime
conditionally in qup_i2c_suspend.

Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
2016-09-22 20:11:14 +02:00
David Wu 72cf8c565c i2c: rk3x: Fix variable 'min_total_ns' unused warning
This patch fixs the following warning:
drivers/i2c/busses/i2c-rk3x.c: In function 'rk3x_i2c_v1_calc_timings':
drivers/i2c/busses/i2c-rk3x.c:745:41: warning: variable 'min_total_ns' set but not used [-Wunused-but-set-variable]

Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-09-22 19:51:38 +02:00
David Wu a8a7d09e73 i2c: rk3x: Fix sparse warning
This patch fixes the following sparse warning:
drivers/i2c/busses/i2c-rk3x.c:888:17: warning: cast truncates bits from constant value (ffffffffff00 becomes ffffff00)

Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-09-22 19:50:15 +02:00
Mika Westerberg 318ce2782a i2c / ACPI: Do not touch an I2C device if it belongs to another adapter
When enumerating I2C devices connected to an I2C adapter we scan the whole
namespace (as it is possible to have devices anywhere in that namespace,
not just below the I2C adapter device) and add each found device to the I2C
bus in question.

Now after commit 525e6fabea ("i2c / ACPI: add support for ACPI
reconfigure notifications") checking of the adapter handle to the one found
in the I2cSerialBus() resource was moved to happen after resources of the
I2C device has been parsed. This means that if the I2cSerialBus() resource
points to an adapter that does not exists in the system we still parse
those resources. This is problematic in particular because
acpi_dev_resource_interrupt() tries to configure GSI if the device also has
an Interrupt() resource. Failing to do that results errrors like this to be
printed on the console:

  [   10.409490] ERROR: Unable to locate IOAPIC for GSI 37

To fix this we pass the I2C adapter to i2c_acpi_get_info() and make sure
the handle matches the one in the I2cSerialBus() resource before doing
anything else to the device.

Reported-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-09-22 19:45:51 +02:00
Peter Rosin 463e8f845c i2c: mux: pca954x: retry updating the mux selection on failure
The cached value of the last selected channel prevents retries on the
next call, even on failure to update the selected channel. Fix that.

Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
2016-09-21 23:10:21 +02:00
Jan Glauber 38caa925ee i2c: octeon: Fix high-level controller status check
In case the high-level controller (HLC) is used the status code is
reported at a different location. Check that location after HLC
write operations if the ready bit is not set and return an appropriate
error code instead of always returning -EAGAIN.

Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-09-21 23:04:42 +02:00
Dmitry Bazhenov de919ff6a0 i2c: octeon: Avoid sending STOP during recovery
Due to a bug in the ThunderX I2C hardware sending STOP during
a recovery attempt could lock up the hardware. To work around
this problem do not send STOP at the beginning of the recovery
but use the override registers to bring the TWSI including
the high-level controller out of the bad state.

Signed-off-by: Dmitry Bazhenov <dmitry.bazhenov@auriga.com>
Signed-off-by: Jan Glauber <jglauber@cavium.com>
[Changed commit message]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-09-21 23:04:35 +02:00
Dmitry Bazhenov e7051556b6 i2c: octeon: Fix set SCL recovery function
The set SCL recovery function unconditionally pulls the SCL line low.
Only pull SCL line low according to val parameter.

Signed-off-by: Dmitry Bazhenov <dmitry.bazhenov@auriga.com>
Signed-off-by: Jan Glauber <jglauber@cavium.com>
[Changed commit message]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-09-21 22:58:25 +02:00
Yadi.hu 371a015344 i2c-eg20t: fix race between i2c init and interrupt enable
the eg20t driver call request_irq() function before the pch_base_address,
base address of i2c controller's register, is assigned an effective value.

there is one possible scenario that an interrupt which isn't inside eg20t
arrives immediately after request_irq() is executed when i2c controller
shares an interrupt number with others. since the interrupt handler
pch_i2c_handler() has already active as shared action, it will be called
and read its own register to determine if this interrupt is from itself.

At that moment, since base address of i2c registers is not remapped
in kernel space yet,so the INT handler will access an illegal address
and then a error occurs.

Signed-off-by: Yadi.hu <yadi.hu@windriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
2016-09-21 18:07:51 +02:00
Ulrich Hecht c13f743aee i2c: rcar: add support for r8a7796 (R-Car M3-W)
Same as r8a7795.

Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-09-16 19:46:10 +02:00
Yang Li fd8961c5ba i2c: imx: make bus recovery through pinctrl optional
Since commit 1c4b6c3bcf ("i2c: imx: implement bus recovery") the
driver starts to use gpio/pinctrl to support optional bus recovery
feature.  But pinctrl is not always usable.  There are platforms such
as ls1021a and ls1043a that don't support pinctrl, and it could just
be broken due to old/broken device tree.  The patch makes it really
optional that the probe function won't bailout on pinctrl problems
instead it just disables bus recovery and prints out notification when
there is problem with pinctrl.  Since pinctrl is only used by bus
recovery in this driver, move pinctrl initialization into bus recovery
init function to prevent confusion.

Signed-off-by: Li Yang <leoyang.li@nxp.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-09-15 21:44:18 +02:00
Neil Armstrong d1050caea4 i2c: meson: add gxbb compatible string
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-09-15 21:37:16 +02:00
Doug Anderson cbfff439c5 i2c: rk3x: Restore clock settings at resume time
Depending on a number of factors including:
- Which exact Rockchip SoC we're working with
- How deep we suspend
- Which i2c port we're on

We might lose the state of the i2c registers at suspend time.
Specifically we've found that on rk3399 the i2c ports that are not in
the PMU power domain lose their state with the current suspend depth
configured by ARM Tursted Firmware.

Note that there are very few actual i2c registers that aren't configured
per transfer anyway so all we actually need to re-configure are the
clock config registers.  We'll just add a call to rk3x_i2c_adapt_div()
at resume time and be done with it.

NOTE: On rk3399 on ports whose power was lost, I put printouts in at
resume time.  I saw things like:
  before: con=0x00010300, div=0x00060006
  after:  con=0x00010200, div=0x00180025

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: David Wu <david.wu@rock-chips.com>
Tested-by: David Wu <david.wu@rock-chips.com>
[wsa: removed duplicate const]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-09-08 22:50:33 +02:00
Masahiro Yamada 0b1c7716fd i2c: uniphier-f: set the adapter to master mode when probing
Currently, the adapter is set to the master mode at the first use.
Since then, it is kept in the slave mode, so unexpected glitch
signals on the I2C lines may cause the adapter into insane state.
Setting it to the master mode along with initialization solves the
problem.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Akio Noda <noda.akio@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-09-08 22:41:31 +02:00
Masahiro Yamada 405188e86a i2c: uniphier-f: avoid WARN_ON() of clk_disable() in failure path
If clk_prepare_enable() fails, clk_disable_unprepare() is called in
the failure path, where the enable_count is still zero, so it hits
WARN_ON(core->enable_count == 0) in the clk_core_disable().

To fix this, make the clock setting more linear in the probe function
so that it can exploit "goto err" in case of error.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-09-08 22:41:02 +02:00
Masahiro Yamada 4c91307ce9 i2c: uniphier: avoid WARN_ON() of clk_disable() in failure path
If clk_prepare_enable() fails, clk_disable_unprepare() is called in
the failure path, where the enable_count is still zero, so it hits
WARN_ON(core->enable_count == 0) in the clk_core_disable().

To fix this, make the clock setting more linear in the probe function
so that it can exploit "goto err" in case of error.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-09-08 22:40:32 +02:00
Jon Hunter fbf8090b72 i2c: tegra: Fix assignment of boolean variables
Fix the following warnings reported by coccinelle for the Tegra I2C
driver.

drivers/i2c/busses/i2c-tegra.c:513:2-23: WARNING: Assignment of bool to 0/1
drivers/i2c/busses/i2c-tegra.c:539:3-24: WARNING: Assignment of bool to 0/1

Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-09-08 22:36:18 +02:00
Shardar Shariff Md 77821b4678 i2c: tegra: proper handling of error cases
To summarize the issue observed in error cases:

SW Flow: For i2c message transfer, packet header and data payload is
posted and then required error/packet completion interrupts are enabled
later.

HW flow: HW process the packet just after packet header is posted, if
ARB lost/NACK error occurs (SW will not handle immediately when error
happens as error interrupts are not enabled at this point). HW assumes
error is acknowledged and clears current data in FIFO, But SW here posts
the remaining data payload which still stays in FIFO as stale data
(data without packet header).

Now once the interrupts are enabled, SW handles ARB lost/NACK error by
clearing the ARB lost/NACK interrupt. Now HW assumes that SW attended
the error and will parse/process stale data (data without packet header)
present in FIFO which causes invalid NACK errors.

Fix: Enable the error interrupts before posting the packet into FIFO
which make sure HW to not clear the fifo. Also disable the packet mode
before acknowledging errors (ARB lost/NACK error) to not process any
stale data. As error interrupts are enabled before posting the packet
header use spinlock to avoid preempting.

Signed-off-by: Shardar Shariff Md <smohammed@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2016-09-08 22:34:58 +02:00