Variable block is an unsigned long long hence the less than zero
comparison is always false, hence it is redundant and can be removed.
Addresses-Coverity: ("Unsigned compared against 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Bryan Gurney <bgurney@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Commit b592211c33 ("dm mpath: fix attached_handler_name leak and
dangling hw_handler_name pointer") fixed a memory leak for the case
where setup_scsi_dh() returns failure. But setup_scsi_dh may return
success and not "use" attached_handler_name if the
retain_attached_hwhandler flag is not set on the map. As setup_scsi_sh
properly "steals" the pointer by nullifying it, freeing it
unconditionally in parse_path() is safe.
Fixes: b592211c33 ("dm mpath: fix attached_handler_name leak and dangling hw_handler_name pointer")
Cc: stable@vger.kernel.org
Reported-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
dm-init should allow up to DM_MAX_{DEVICES,TARGETS} for devices/targets,
and not DM_MAX_{DEVICES,TARGETS} - 1.
Fix the checks and also fix the error message when the number of devices
is surpassed.
Fixes: 6bbc923dfc ("dm: add support to directly boot to a mapped device")
Cc: stable@vger.kernel.org
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add the dm-dust target, which simulates the behavior of bad sectors
at arbitrary locations, and the ability to enable the emulation of
the read failures at an arbitrary time.
This target behaves similarly to a linear target. At a given time,
the user can send a message to the target to start failing read
requests on specific blocks. When the failure behavior is enabled,
reads of blocks configured "bad" will fail with EIO.
Writes of blocks configured "bad" will result in the following:
1. Remove the block from the "bad block list".
2. Successfully complete the write.
After this point, the block will successfully contain the written
data, and will service reads and writes normally. This emulates the
behavior of a "remapped sector" on a hard disk drive.
dm-dust provides logging of which blocks have been added or removed
to the "bad block list", as well as logging when a block has been
removed from the bad block list. These messages can be used
alongside the messages from the driver using a dm-dust device to
analyze the driver's behavior when a read fails at a given time.
(This logging can be reduced via a "quiet" mode, if desired.)
NOTE: If the block size is larger than 512 bytes, only the first sector
of each "dust block" is detected. Placing a limiting layer above a dust
target, to limit the minimum I/O size to the dust block size, will
ensure proper emulation of the given large block size.
Signed-off-by: Bryan Gurney <bgurney@redhat.com>
Co-developed-by: Joe Shimkus <jshimkus@redhat.com>
Co-developed-by: John Dorminy <jdorminy@redhat.com>
Co-developed-by: John Pittman <jpittman@redhat.com>
Co-developed-by: Thomas Jaskiewicz <tjaskiew@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This is a small optimization in writecache_find_entry().
If we go past the condition "if (unlikely(!node))", we can be certain that
there is no entry in the tree that has the block equal to the "block"
variable.
Consequently, we can return the next entry directly, we don't need to go
to the second part of the function that finds the entry with lowest or
highest seq number that matches the "block" variable.
Also, add some whitespace and cleanup needless braces.
Suggested-by: Huaisheng Ye <yehs1@lenovo.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The stucture member page_offset in writeback_struct never has been
used actually. Remove it.
Signed-off-by: Huaisheng Ye <yehs1@lenovo.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When the target line contains an invalid device, delay_ctr() will call
delay_dtr() with NULL workqueue. Attempting to destroy the NULL
workqueue causes a crash.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
md->dax_dev defaults to NULL and there is no need to initialize it
if CONFIG_DAX_DRIVER is disabled.
Signed-off-by: Peng Wang <rocking@whu.edu.cn>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
After commit 396eaf21ee ("blk-mq: improve DM's blk-mq IO merging via
blk_insert_cloned_request feedback"), map_request() will requeue the tio
when issued clone request return BLK_STS_RESOURCE or BLK_STS_DEV_RESOURCE.
Thus, if device driver status is error, a tio may be requeued multiple
times until the return value is not DM_MAPIO_REQUEUE. That means
type->start_io may be called multiple times, while type->end_io is only
called when IO complete.
In fact, even without commit 396eaf21ee, setup_clone() failure can
also cause tio requeue and associated missed call to type->end_io.
The service-time path selector selects path based on in_flight_size,
which is increased by st_start_io() and decreased by st_end_io().
Missed calls to st_end_io() can lead to in_flight_size count error and
will cause the selector to make the wrong choice. In addition,
queue-length path selector will also be affected.
To fix the problem, call type->end_io in ->release_clone_rq before tio
requeue. map_info is passed to ->release_clone_rq() for map_request()
error path that result in requeue.
Fixes: 396eaf21ee ("blk-mq: improve DM's blk-mq IO merging via blk_insert_cloned_request feedback")
Cc: stable@vger.kernl.org
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Otherwise, just activating a thin-pool and thin device and then
deactivating them will cause the thin-pool metadata to be changed
(e.g. superblock written) -- even without any metadata being changed.
Add 'in_service' flag to struct dm_pool_metadata and set it in
pmd_write_lock() because all on-disk metadata changes must take a write
lock of pmd->root_lock. Once 'in_service' is set it is never cleared.
__commit_transaction() will return 0 if 'in_service' is not set.
dm_pool_commit_metadata() is updated to use __pmd_write_lock() so that
it isn't the sole reason for putting a thin-pool in service.
Also fix dm_pool_commit_metadata() to open the next transaction if the
return from __commit_transaction() is 0. Not seeing why the early
return ever made since for a return of 0 given that dm-io's async_io(),
as used by bufio, always returns 0.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
No functional change, but this prepares to hook off of pmd_write_lock()
with additional functionality (as provided in next commit).
Suggested-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Otherwise, memory that is allocated (and potentially not previously
zeroed) will get written to disk as part of the space maps.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
In functions writecache_discard() and writecache_find_entry() there is a
high probablity that the pointer of structure rb_node won't equal NULL.
Add unlikely for the pointer node NULL.
Signed-off-by: Huaisheng Ye <yehs1@lenovo.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
bio is already available so there is no need to access it in terms of
the wb pointer.
Signed-off-by: Huaisheng Ye <yehs1@lenovo.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Substitute the global locking scheme with a fine grained one, employing
the read-write semaphore and the scalable exception tables with
per-bucket locks introduced by the previous two commits.
Summarizing, we now use a read-write semaphore to protect the mostly
read fields of the snapshot structure, e.g., valid, active, etc., and
per-bucket bit spinlocks to protect accesses to the complete and pending
exception tables.
Finally, we use an extra spinlock (pe_allocation_lock) to serialize the
allocation of new exceptions by the exception store. This allocation is
really fast, so the extra spinlock doesn't hurt the performance.
This scheme allows dm-snapshot to scale better, resulting in increased
IOPS and reduced latency.
Following are some benchmark results using the null_blk device:
modprobe null_blk gb=1024 bs=512 submit_queues=8 hw_queue_depth=4096 \
queue_mode=2 irqmode=1 completion_nsec=1 nr_devices=1
* Benchmark fio_origin_randwrite_throughput_N, from the device mapper
test suite [1] (direct IO, random 4K writes to origin device, IO
engine libaio):
+--------------+-------------+------------+
| # of workers | IOPS Before | IOPS After |
+--------------+-------------+------------+
| 1 | 57708 | 66421 |
| 2 | 63415 | 77589 |
| 4 | 67276 | 98839 |
| 8 | 60564 | 109258 |
+--------------+-------------+------------+
* Benchmark fio_origin_randwrite_latency_N, from the device mapper test
suite [1] (direct IO, random 4K writes to origin device, IO engine
psync):
+--------------+-----------------------+----------------------+
| # of workers | Latency (usec) Before | Latency (usec) After |
+--------------+-----------------------+----------------------+
| 1 | 16.25 | 13.27 |
| 2 | 31.65 | 25.08 |
| 4 | 55.28 | 41.08 |
| 8 | 121.47 | 74.44 |
+--------------+-----------------------+----------------------+
* Benchmark fio_snapshot_randwrite_throughput_N, from the device mapper
test suite [1] (direct IO, random 4K writes to snapshot device, IO
engine libaio):
+--------------+-------------+------------+
| # of workers | IOPS Before | IOPS After |
+--------------+-------------+------------+
| 1 | 72593 | 84938 |
| 2 | 97379 | 134973 |
| 4 | 90610 | 143077 |
| 8 | 90537 | 180085 |
+--------------+-------------+------------+
* Benchmark fio_snapshot_randwrite_latency_N, from the device mapper
test suite [1] (direct IO, random 4K writes to snapshot device, IO
engine psync):
+--------------+-----------------------+----------------------+
| # of workers | Latency (usec) Before | Latency (usec) After |
+--------------+-----------------------+----------------------+
| 1 | 12.53 | 10.6 |
| 2 | 19.78 | 14.89 |
| 4 | 40.37 | 23.47 |
| 8 | 89.32 | 48.48 |
+--------------+-----------------------+----------------------+
[1] https://github.com/jthornber/device-mapper-test-suite
Co-developed-by: Ilias Tsitsimpis <iliastsi@arrikto.com>
Signed-off-by: Nikos Tsironis <ntsironis@arrikto.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Use list_bl to implement the exception hash tables' buckets. This change
permits concurrent access, to distinct buckets, by multiple threads.
Also, implement helper functions to lock and unlock the exception tables
based on the chunk number of the exception at hand.
We retain the global locking, by means of down_write(), which is
replaced by the next commit.
Still, we must acquire the per-bucket spinlocks when accessing the hash
tables, since list_bl does not allow modification on unlocked lists.
Co-developed-by: Ilias Tsitsimpis <iliastsi@arrikto.com>
Signed-off-by: Nikos Tsironis <ntsironis@arrikto.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
dm-snapshot uses a single mutex to serialize every access to the
snapshot state. This includes all accesses to the complete and pending
exception tables, which occur at every origin write, every snapshot
read/write and every exception completion.
The lock statistics indicate that this mutex is a bottleneck (average
wait time ~480 usecs for 8 processes doing random 4K writes to the
origin device) preventing dm-snapshot to scale as the number of threads
doing IO increases.
The major contention points are __origin_write()/snapshot_map() and
pending_complete(), i.e., the submission and completion of pending
exceptions.
Replace this mutex with a rw semaphore.
We essentially revert commit ae1093be5a ("dm snapshot: use mutex
instead of rw_semaphore") and together with the next two patches we
substitute the single mutex with a fine-grained locking scheme, where we
use a read-write semaphore to protect the mostly read fields of the
snapshot structure, e.g., valid, active, etc., and per-bucket bit
spinlocks to protect accesses to the complete and pending exception
tables.
Co-developed-by: Ilias Tsitsimpis <iliastsi@arrikto.com>
Signed-off-by: Nikos Tsironis <ntsironis@arrikto.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When completing a pending exception, pending_complete() waits for all
conflicting reads to drain, before inserting the final, completed
exception. Conflicting reads are snapshot reads redirected to the
origin, because the relevant chunk is not remapped to the COW device the
moment we receive the read.
The completed exception must be inserted into the exception table after
all conflicting reads drain to ensure snapshot reads don't return
corrupted data. This is required because inserting the completed
exception into the exception table signals that the relevant chunk is
remapped and both origin writes and snapshot merging will now overwrite
the chunk in origin.
This wait is done holding the snapshot lock to ensure that
pending_complete() doesn't starve if new snapshot reads keep coming for
this chunk.
In preparation for the next commit, where we use a spinlock instead of a
mutex to protect the exception tables, we remove the need for holding
the lock while waiting for conflicting reads to drain.
We achieve this in two steps:
1. pending_complete() inserts the completed exception before waiting for
conflicting reads to drain and removes the pending exception after
all conflicting reads drain.
This ensures that new snapshot reads will be redirected to the COW
device, instead of the origin, and thus pending_complete() will not
starve. Moreover, we use the existence of both a completed and
a pending exception to signify that the COW is done but there are
conflicting reads in flight.
2. In __origin_write() we check first if there is a pending exception
and then if there is a completed exception. If there is a pending
exception any submitted BIO is delayed on the pe->origin_bios list and
DM_MAPIO_SUBMITTED is returned. This ensures that neither writes to the
origin nor snapshot merging can overwrite the origin chunk, until all
conflicting reads drain, and thus snapshot reads will not return
corrupted data.
Summarizing, we now have the following possible combinations of pending
and completed exceptions for a chunk, along with their meaning:
A. No exceptions exist: The chunk has not been remapped yet.
B. Only a pending exception exists: The chunk is currently being copied
to the COW device.
C. Both a pending and a completed exception exist: COW for this chunk
has completed but there are snapshot reads in flight which had been
redirected to the origin before the chunk was remapped.
D. Only the completed exception exists: COW has been completed and there
are no conflicting reads in flight.
Co-developed-by: Ilias Tsitsimpis <iliastsi@arrikto.com>
Signed-off-by: Nikos Tsironis <ntsironis@arrikto.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add missing dm_bitset_cursor_next() to properly advance the bitset
cursor.
Otherwise, the discarded state of all blocks is set according to the
discarded state of the first block.
Fixes: ae4a46a1f6 ("dm cache metadata: use bitset cursor api to load discard bitset")
Cc: stable@vger.kernel.org
Signed-off-by: Nikos Tsironis <ntsironis@arrikto.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The function blkdev_report_zones() returns success even if no zone
information is reported (empty report). Empty zone reports can only
happen if the report start sector passed exceeds the device capacity.
The conditions for this to happen are either a bug in the caller code,
or, a change in the device that forced the low level driver to change
the device capacity to a value that is lower than the report start
sector. This situation includes a failed disk revalidation resulting in
the disk capacity being changed to 0.
If this change happens while dm-zoned is in its initialization phase
executing dmz_init_zones(), this function may enter an infinite loop
and hang the system. To avoid this, add a check to disallow empty zone
reports and bail out early. Also fix the function dmz_update_zone() to
make sure that the report for the requested zone was correctly obtained.
Fixes: 3b1a94c88b ("dm zoned: drive-managed zoned block device target")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Shaun Tancheff <shaun@tancheff.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
My static checker complains about this line from dmz_get_zoned_device()
aligned_capacity = dev->capacity & ~(blk_queue_zone_sectors(q) - 1);
The problem is that "aligned_capacity" and "dev->capacity" are sector_t
type (which is a u64 under most configs) but blk_queue_zone_sectors(q)
returns a u32 so the higher 32 bits in aligned_capacity are cleared to
zero. This patch adds a cast to address the issue.
Fixes: 114e025968 ("dm zoned: ignore last smaller runt zone")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The sector used here is a little endian value, so use the right
type for it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
dm-integrity will deadlock if overlapping I/O is issued to it, the bug
was introduced by commit 724376a04d ("dm integrity: implement fair
range locks"). Users rarely use overlapping I/O so this bug went
undetected until now.
Fix this bug by correcting, likely cut-n-paste, typos in
ranges_overlap() and also remove a flawed ranges_overlap() check in
remove_range_unlocked(). This condition could leave unprocessed bios
hanging on wait_list forever.
Cc: stable@vger.kernel.org # v4.19+
Fixes: 724376a04d ("dm integrity: implement fair range locks")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Storage devices which report supporting discard commands like
WRITE_SAME_16 with unmap, but reject discard commands sent to the
storage device. This is a clear storage firmware bug but it doesn't
change the fact that should a program cause discards to be sent to a
multipath device layered on this buggy storage, all paths can end up
failed at the same time from the discards, causing possible I/O loss.
The first discard to a path will fail with Illegal Request, Invalid
field in cdb, e.g.:
kernel: sd 8:0:8:19: [sdfn] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
kernel: sd 8:0:8:19: [sdfn] tag#0 Sense Key : Illegal Request [current]
kernel: sd 8:0:8:19: [sdfn] tag#0 Add. Sense: Invalid field in cdb
kernel: sd 8:0:8:19: [sdfn] tag#0 CDB: Write same(16) 93 08 00 00 00 00 00 a0 08 00 00 00 80 00 00 00
kernel: blk_update_request: critical target error, dev sdfn, sector 10487808
The SCSI layer converts this to the BLK_STS_TARGET error number, the sd
device disables its support for discard on this path, and because of the
BLK_STS_TARGET error multipath fails the discard without failing any
path or retrying down a different path. But subsequent discards can
cause path failures. Any discards sent to the path which already failed
a discard ends up failing with EIO from blk_cloned_rq_check_limits with
an "over max size limit" error since the discard limit was set to 0 by
the sd driver for the path. As the error is EIO, this now fails the
path and multipath tries to send the discard down the next path. This
cycle continues as discards are sent until all paths fail.
Fix this by training DM core to disable DISCARD if the underlying
storage already did so.
Also, fix branching in dm_done() and clone_endio() to reflect the
mutually exclussive nature of the IO operations in question.
Cc: stable@vger.kernel.org
Reported-by: David Jeffery <djeffery@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Some devices don't use blk_integrity but still want stable pages
because they do their own checksumming. Examples include rbd and iSCSI
when data digests are negotiated. Stacking DM (and thus LVM) on top of
these devices results in sporadic checksum errors.
Set BDI_CAP_STABLE_WRITES if any underlying device has it set.
Cc: stable@vger.kernel.org
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The limit was already incorporated to dm-crypt with commit 4e870e948f
("dm crypt: fix error with too large bios"), so we don't need to apply
it globally to all targets. The quantity BIO_MAX_PAGES * PAGE_SIZE is
wrong anyway because the variable ti->max_io_len it is supposed to be in
the units of 512-byte sectors not in bytes.
Reduction of the limit to 1048576 sectors could even cause data
corruption in rare cases - suppose that we have a dm-striped device with
stripe size 768MiB. The target will call dm_set_target_max_io_len with
the value 1572864. The buggy code would reduce it to 1048576. Now, the
dm-core will errorneously split the bios on 1048576-sector boundary
insetad of 1572864-sector boundary and pass these stripe-crossing bios
to the striped target.
Cc: stable@vger.kernel.org # v4.16+
Fixes: 8f50e35815 ("dm: limit the max bio size as BIO_MAX_PAGES * PAGE_SIZE")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
A non const pointer to const cannot be marked initconst.
Mark the array actually const.
Fixes: 6bbc923dfc dm: add support to directly boot to a mapped device
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Fix sparse warnings:
drivers/md/dm-integrity.c:3619:12: warning:
symbol 'dm_integrity_init' was not declared. Should it be static?
drivers/md/dm-integrity.c:3638:6: warning:
symbol 'dm_integrity_exit' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
If the string opt_string is small, the function memcmp can access bytes
that are beyond the terminating nul character. In theory, it could cause
segfault, if opt_string were located just below some unmapped memory.
Change from memcmp to strncmp so that we don't read bytes beyond the end
of the string.
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
-----BEGIN PGP SIGNATURE-----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=qBae
-----END PGP SIGNATURE-----
Merge tag 'for-5.1/block-post-20190315' of git://git.kernel.dk/linux-block
Pull more block layer changes from Jens Axboe:
"This is a collection of both stragglers, and fixes that came in after
I finalized the initial pull. This contains:
- An MD pull request from Song, with a few minor fixes
- Set of NVMe patches via Christoph
- Pull request from Konrad, with a few fixes for xen/blkback
- pblk fix IO calculation fix (Javier)
- Segment calculation fix for pass-through (Ming)
- Fallthrough annotation for blkcg (Mathieu)"
* tag 'for-5.1/block-post-20190315' of git://git.kernel.dk/linux-block: (25 commits)
blkcg: annotate implicit fall through
nvme-tcp: support C2HData with SUCCESS flag
nvmet: ignore EOPNOTSUPP for discard
nvme: add proper write zeroes setup for the multipath device
nvme: add proper discard setup for the multipath device
nvme: remove nvme_ns_config_oncs
nvme: disable Write Zeroes for qemu controllers
nvmet-fc: bring Disconnect into compliance with FC-NVME spec
nvmet-fc: fix issues with targetport assoc_list list walking
nvme-fc: reject reconnect if io queue count is reduced to zero
nvme-fc: fix numa_node when dev is null
nvme-fc: use nr_phys_segments to determine existence of sgl
nvme-loop: init nvmet_ctrl fatal_err_work when allocate
nvme: update comment to make the code easier to read
nvme: put ns_head ref if namespace fails allocation
nvme-trace: fix cdw10 buffer overrun
nvme: don't warn on block content change effects
nvme: add get-feature to admin cmds tracer
md: Fix failed allocation of md_register_thread
It's wrong to add len to sector_nr in raid10 reshape twice
...
mddev->sync_thread can be set to NULL on kzalloc failure downstream.
The patch checks for such a scenario and frees allocated resources.
Committer node:
Added similar fix to raid5.c, as suggested by Guoqing.
Cc: stable@vger.kernel.org # v3.16+
Acked-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Song Liu <songliubraving@fb.com>
In reshape_request it already adds len to sector_nr already. It's wrong to add len to
sector_nr again after adding pages to bio. If there is bad block it can't copy one chunk
at a time, it needs to goto read_more. Now the sector_nr is wrong. It can cause data
corruption.
Cc: stable@vger.kernel.org # v3.16+
Signed-off-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
When the Partial Parity Log is enabled, circular buffer is used to store
PPL data. Each write to RAID device causes overwrite of data in this buffer
so some write_hint can be set to those request to help drives handle
garbage collection. This patch adds new sysfs attribute which can be used
to specify which write_hint should be assigned to PPL.
Acked-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Mariusz Dabrowski <mariusz.dabrowski@intel.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
The code really just wants a big flat buffer, so just do that.
Link: http://lkml.kernel.org/r/20181217131929.11727-3-kent.overstreet@gmail.com
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
Reviewed-by: Matthew Wilcox <willy@infradead.org>
Cc: Shaohua Li <shli@kernel.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Eric Paris <eparis@parisplace.org>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Paul Moore <paul@paul-moore.com>
Cc: Pravin B Shelar <pshelar@ovn.org>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
DM targets to properly advertise discard limits that blk_queue_split()
looks at when dtermining to split discard. Whereby allowing DM core's
own 'split_discard_bios' to be removed.
- Improve DM cache target to provide support for discard passdown to the
origin device.
- Introduce support to directly boot to a DM mapped device from init by
using dm-mod.create= module param. This eliminates the need for an
elaborate initramfs that is otherwise needed to create DM devices.
This feature's implementation has been worked on for quite some time
(got up to v12) and is of particular interest to Android and other
more embedded platforms (e.g. ARM).
- Rate limit errors from the DM integrity target that were identified as
the cause for recent NMI hangs due to console limitations.
- Add sanity checks for user input to thin-pool and external snapshot
creation.
- Remove some unused leftover kmem caches from when old .request_fn
request-based support was removed.
- Various small cleanups and fixes to targets (e.g. typos, needless
unlikely() annotations, use struct_size(), remove needless
.direct_access method from dm-snapshot)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcgT+7AAoJEMUj8QotnQNaAsUIAIxsO5y6+7UruZzZxpyYBA34
yBLnZ9SICxESteu4R9lWT4LnFbrdwDDSSCeQ1dFt5/vx54T4qISN/O3lv9e//BeJ
BxFXtu7wB485l28uojBZeb+9APTaoihfEokcfDqZnaf26XtY0t/M+yRP7U86eGcC
zsX9fOEmJ3cpWtpai07tbHNDjIrr1kIWcFuU2+xGO/wn+Up8uLd85exi7e3cqDs6
VC+YJ/10/2keqFQvse3w3TBMjduwpb7SlDa2z/SorYaStVHzgwRSSjWYkSM/eDRA
OkSeRQ3Rnwc+Vad2R8J7unnZlMd4kALjGuzbyafWnitE+C+n0aJFDKqjIwNbKcw=
=GKp5
-----END PGP SIGNATURE-----
Merge tag 'for-5.1/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper updates from Mike Snitzer:
- Update bio-based DM core to always call blk_queue_split() and update
DM targets to properly advertise discard limits that
blk_queue_split() looks at when dtermining to split discard. Whereby
allowing DM core's own 'split_discard_bios' to be removed.
- Improve DM cache target to provide support for discard passdown to
the origin device.
- Introduce support to directly boot to a DM mapped device from init by
using dm-mod.create= module param. This eliminates the need for an
elaborate initramfs that is otherwise needed to create DM devices.
This feature's implementation has been worked on for quite some time
(got up to v12) and is of particular interest to Android and other
more embedded platforms (e.g. ARM).
- Rate limit errors from the DM integrity target that were identified
as the cause for recent NMI hangs due to console limitations.
- Add sanity checks for user input to thin-pool and external snapshot
creation.
- Remove some unused leftover kmem caches from when old .request_fn
request-based support was removed.
- Various small cleanups and fixes to targets (e.g. typos, needless
unlikely() annotations, use struct_size(), remove needless
.direct_access method from dm-snapshot)
* tag 'for-5.1/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm integrity: limit the rate of error messages
dm snapshot: don't define direct_access if we don't support it
dm cache: add support for discard passdown to the origin device
dm writecache: fix typo in name for writeback_wq
dm: add support to directly boot to a mapped device
dm thin: add sanity checks to thin-pool and external snapshot creation
dm block manager: remove redundant unlikely annotation
dm verity fec: remove redundant unlikely annotation
dm integrity: remove redundant unlikely annotation
dm: always call blk_queue_split() in dm_process_bio()
dm: fix to_sector() for 32bit
dm switch: use struct_size() in kzalloc()
dm: remove unused _rq_tio_cache and _rq_cache
dm: eliminate 'split_discard_bios' flag from DM target interface
dm: update dm_process_bio() to split bio if in ->make_request_fn()
-----BEGIN PGP SIGNATURE-----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=VBaU
-----END PGP SIGNATURE-----
Merge tag 'for-5.1/block-20190302' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
"Not a huge amount of changes in this round, the biggest one is that we
finally have Mings multi-page bvec support merged. Apart from that,
this pull request contains:
- Small series that avoids quiescing the queue for sysfs changes that
match what we currently have (Aleksei)
- Series of bcache fixes (via Coly)
- Series of lightnvm fixes (via Mathias)
- NVMe pull request from Christoph. Nothing major, just SPDX/license
cleanups, RR mp policy (Hannes), and little fixes (Bart,
Chaitanya).
- BFQ series (Paolo)
- Save blk-mq cpu -> hw queue mapping, removing a pointer indirection
for the fast path (Jianchao)
- fops->iopoll() added for async IO polling, this is a feature that
the upcoming io_uring interface will use (Christoph, me)
- Partition scan loop fixes (Dongli)
- mtip32xx conversion from managed resource API (Christoph)
- cdrom registration race fix (Guenter)
- MD pull from Song, two minor fixes.
- Various documentation fixes (Marcos)
- Multi-page bvec feature. This brings a lot of nice improvements
with it, like more efficient splitting, larger IOs can be supported
without growing the bvec table size, and so on. (Ming)
- Various little fixes to core and drivers"
* tag 'for-5.1/block-20190302' of git://git.kernel.dk/linux-block: (117 commits)
block: fix updating bio's front segment size
block: Replace function name in string with __func__
nbd: propagate genlmsg_reply return code
floppy: remove set but not used variable 'q'
null_blk: fix checking for REQ_FUA
block: fix NULL pointer dereference in register_disk
fs: fix guard_bio_eod to check for real EOD errors
blk-mq: use HCTX_TYPE_DEFAULT but not 0 to index blk_mq_tag_set->map
block: optimize bvec iteration in bvec_iter_advance
block: introduce mp_bvec_for_each_page() for iterating over page
block: optimize blk_bio_segment_split for single-page bvec
block: optimize __blk_segment_map_sg() for single-page bvec
block: introduce bvec_nth_page()
iomap: wire up the iopoll method
block: add bio_set_polled() helper
block: wire up block device iopoll method
fs: add an iopoll method to struct file_operations
loop: set GENHD_FL_NO_PART_SCAN after blkdev_reread_part()
loop: do not print warn message if partition scan is successful
block: bounce: make sure that bvec table is updated
...
When using dm-integrity underneath md-raid, some tests with raid
auto-correction trigger large amounts of integrity failures - and all
these failures print an error message. These messages can bring the
system to a halt if the system is using serial console.
Fix this by limiting the rate of error messages - it improves the speed
of raid recovery and avoids the hang.
Fixes: 7eada909bf ("dm: add integrity target")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Don't define a direct_access function that fails, dm_dax_direct_access
already fails with -EIO if the pointer is zero;
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
DM cache now defaults to passing discards down to the origin device.
User may disable this using the "no_discard_passdown" feature when
creating the cache device.
If the cache's underlying origin device doesn't support discards then
passdown is disabled (with warning). Similarly, if the underlying
origin device's max_discard_sectors is less than a cache block discard
passdown will be disabled (this is required because sizing of the cache
internal discard bitset depends on it).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The workqueue's name should be "writecache-writeback" instead of
"writecache-writeabck".
Signed-off-by: Huaisheng Ye <yehs1@lenovo.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add a "create" module parameter, which allows device-mapper targets to
be configured at boot time. This enables early use of DM targets in the
boot process (as the root device or otherwise) without the need of an
initramfs.
The syntax used in the boot param is based on the concise format from
the dmsetup tool to follow the rule of least surprise:
dmsetup table --concise /dev/mapper/lroot
Which is:
dm-mod.create=<name>,<uuid>,<minor>,<flags>,<table>[,<table>+][;<name>,<uuid>,<minor>,<flags>,<table>[,<table>+]+]
Where,
<name> ::= The device name.
<uuid> ::= xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx | ""
<minor> ::= The device minor number | ""
<flags> ::= "ro" | "rw"
<table> ::= <start_sector> <num_sectors> <target_type> <target_args>
<target_type> ::= "verity" | "linear" | ...
For example, the following could be added in the boot parameters:
dm-mod.create="lroot,,,rw, 0 4096 linear 98:16 0, 4096 4096 linear 98:32 0" root=/dev/dm-0
Only the targets that were tested are allowed and the ones that don't
change any block device when the device is create as read-only. For
example, mirror and cache targets are not allowed. The rationale behind
this is that if the user makes a mistake, choosing the wrong device to
be the mirror or the cache can corrupt data.
The only targets initially allowed are:
* crypt
* delay
* linear
* snapshot-origin
* striped
* verity
Co-developed-by: Will Drewry <wad@chromium.org>
Co-developed-by: Kees Cook <keescook@chromium.org>
Co-developed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Invoking dm_get_device() twice on the same device path with different
modes is dangerous. Because in that case, upgrade_mode() will alloc a
new 'dm_dev' and free the old one, which may be referenced by a previous
caller. Dereferencing the dangling pointer will trigger kernel NULL
pointer dereference.
The following two cases can reproduce this issue. Actually, they are
invalid setups that must be disallowed, e.g.:
1. Creating a thin-pool with read_only mode, and the same device as
both metadata and data.
dmsetup create thinp --table \
"0 41943040 thin-pool /dev/vdb /dev/vdb 128 0 1 read_only"
BUG: unable to handle kernel NULL pointer dereference at 0000000000000080
...
Call Trace:
new_read+0xfb/0x110 [dm_bufio]
dm_bm_read_lock+0x43/0x190 [dm_persistent_data]
? kmem_cache_alloc_trace+0x15c/0x1e0
__create_persistent_data_objects+0x65/0x3e0 [dm_thin_pool]
dm_pool_metadata_open+0x8c/0xf0 [dm_thin_pool]
pool_ctr.cold.79+0x213/0x913 [dm_thin_pool]
? realloc_argv+0x50/0x70 [dm_mod]
dm_table_add_target+0x14e/0x330 [dm_mod]
table_load+0x122/0x2e0 [dm_mod]
? dev_status+0x40/0x40 [dm_mod]
ctl_ioctl+0x1aa/0x3e0 [dm_mod]
dm_ctl_ioctl+0xa/0x10 [dm_mod]
do_vfs_ioctl+0xa2/0x600
? handle_mm_fault+0xda/0x200
? __do_page_fault+0x26c/0x4f0
ksys_ioctl+0x60/0x90
__x64_sys_ioctl+0x16/0x20
do_syscall_64+0x55/0x150
entry_SYSCALL_64_after_hwframe+0x44/0xa9
2. Creating a external snapshot using the same thin-pool device.
dmsetup create thinp --table \
"0 41943040 thin-pool /dev/vdc /dev/vdb 128 0 2 ignore_discard"
dmsetup message /dev/mapper/thinp 0 "create_thin 0"
dmsetup create snap --table \
"0 204800 thin /dev/mapper/thinp 0 /dev/mapper/thinp"
BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
...
Call Trace:
? __alloc_pages_nodemask+0x13c/0x2e0
retrieve_status+0xa5/0x1f0 [dm_mod]
? dm_get_live_or_inactive_table.isra.7+0x20/0x20 [dm_mod]
table_status+0x61/0xa0 [dm_mod]
ctl_ioctl+0x1aa/0x3e0 [dm_mod]
dm_ctl_ioctl+0xa/0x10 [dm_mod]
do_vfs_ioctl+0xa2/0x600
ksys_ioctl+0x60/0x90
? ksys_write+0x4f/0xb0
__x64_sys_ioctl+0x16/0x20
do_syscall_64+0x55/0x150
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Signed-off-by: Jason Cai (Xiang Feng) <jason.cai@linux.alibaba.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
unlikely has already included in IS_ERR(),
so just remove redundant unlikely annotation.
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
unlikely has already included in IS_ERR(),
so just remove redundant unlikely annotation.
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
unlikely has already included in IS_ERR(),
so just remove redundant unlikely annotation.
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Do not just call blk_queue_split() if the bio is_abnormal_io().
Fixes: 568c73a355 ("dm: update dm_process_bio() to split bio if in ->make_request_fn()")
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
There is no need to have DM core split discards on behalf of a DM target
now that blk_queue_split() handles splitting discards based on the
queue_limits. A DM target just needs to set max_discard_sectors,
discard_granularity, etc, in queue_limits.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Colin Ian King