Initialize data->config_lock mutex before it is used by the driver code.
This fixes following warning on Odroid XU3 boards:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 5 PID: 1 Comm: swapper/0 Not tainted 4.15.0-rc7-next-20180115-00001-gb75575dee3f2 #107
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[<c0111504>] (unwind_backtrace) from [<c010dbec>] (show_stack+0x10/0x14)
[<c010dbec>] (show_stack) from [<c09b3f74>] (dump_stack+0x90/0xc8)
[<c09b3f74>] (dump_stack) from [<c0179528>] (register_lock_class+0x1c0/0x59c)
[<c0179528>] (register_lock_class) from [<c017bd1c>] (__lock_acquire+0x78/0x1850)
[<c017bd1c>] (__lock_acquire) from [<c017de30>] (lock_acquire+0xc8/0x2b8)
[<c017de30>] (lock_acquire) from [<c09ca59c>] (__mutex_lock+0x60/0xa0c)
[<c09ca59c>] (__mutex_lock) from [<c09cafd0>] (mutex_lock_nested+0x1c/0x24)
[<c09cafd0>] (mutex_lock_nested) from [<c068b0d0>] (ina2xx_set_shunt+0x70/0xb0)
[<c068b0d0>] (ina2xx_set_shunt) from [<c068b218>] (ina2xx_probe+0x88/0x1b0)
[<c068b218>] (ina2xx_probe) from [<c0673d90>] (i2c_device_probe+0x1e0/0x2d0)
[<c0673d90>] (i2c_device_probe) from [<c053a268>] (driver_probe_device+0x2b8/0x4a0)
[<c053a268>] (driver_probe_device) from [<c053a54c>] (__driver_attach+0xfc/0x120)
[<c053a54c>] (__driver_attach) from [<c05384cc>] (bus_for_each_dev+0x58/0x7c)
[<c05384cc>] (bus_for_each_dev) from [<c0539590>] (bus_add_driver+0x174/0x250)
[<c0539590>] (bus_add_driver) from [<c053b5e0>] (driver_register+0x78/0xf4)
[<c053b5e0>] (driver_register) from [<c0675ef0>] (i2c_register_driver+0x38/0xa8)
[<c0675ef0>] (i2c_register_driver) from [<c0102b40>] (do_one_initcall+0x48/0x18c)
[<c0102b40>] (do_one_initcall) from [<c0e00df0>] (kernel_init_freeable+0x110/0x1d4)
[<c0e00df0>] (kernel_init_freeable) from [<c09c8120>] (kernel_init+0x8/0x114)
[<c09c8120>] (kernel_init) from [<c01010b4>] (ret_from_fork+0x14/0x20)
Fixes: 5d389b1251 ("hwmon: (ina2xx) Make calibration register value fixed")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Calibration register is used for calculating current register in
hardware according to datasheet:
current = shunt_volt * calib_register / 2048 (ina 226)
current = shunt_volt * calib_register / 4096 (ina 219)
Fix calib_register value to 2048 for ina226 and 4096 for ina 219 in
order to avoid truncation error and provide best precision allowed
by shunt_voltage measurement. Make current scale value follow changes
of shunt_resistor from sysfs as calib_register value is now fixed.
Power_lsb value should also follow shunt_resistor changes as stated in
datasheet:
power_lsb = 25 * current_lsb (ina 226)
power_lsb = 20 * current_lsb (ina 219)
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
when checking for the value of the shunt resistor.
Signed-off-by: Marc Titinger <mtitinger@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Any sysfs "show" read access from the client app will result in reading
all registers (8 with ina226). Depending on the host this can limit the
best achievable read rate.
This changeset allows for individual register accesses through regmap.
Tested with BeagleBone Black (Baylibre-ACME) and ina226.
Signed-off-by: Marc Titinger <mtitinger@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use find_closest() to locate the closest average in ina226_avg_tab.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for "ina231" as compatible string, and update
Documentation and Kconfig accordingly.
Tested with the Exynos5422-based odroid-xu3 board which has on-board
INA231 sensors.
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DIV_ROUND_CLOSEST() when dealing with the calibration values to make the
calculations less error prone.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This attribute allows to configure the update interval of ina226. Although
the bus and shunt voltage conversion times remain hardcoded to 1.1 ms, we can
now modify said interval by changing the averaging rate.
While we're at it - add an additional variable to ina2xx_data, which holds
the current configuration settings - this way we'll be able to restore the
configuration in case of an unexpected chip reset.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The shunt resistance can only be set via platform_data or device tree. This
isn't suitable for devices in which the shunt resistance can change/isn't
known at boot-time.
Add a sysfs attribute that allows to read and set the shunt resistance.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Shunt resistance values greater than the chip's calibration factor make no
sense since the actual value written to the register equals:
<calibration factor> / <shunt>
Bail-out from ina2xx_probe() if the configured value is greater than the
calibration factor.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Chips from the ina family don't like to be uninitialized. In case the power
is cut-off and restored again the calibration register will be reset
to 0 and both the power and current registers will remain at 0.
Check the calibration register in ina2xx_update_device() and reinitialize
the chip if needed.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The return value of i2c_smbus_write_word_swapped() isn't checked in
ina2xx_probe(). This leads to devices being registered even if they cannot
be physically detected (e.g. device is not powered-up at boot-time).
Even after restoring power to such device, it is left unconfigured as the
configuration has never been actually written to the register.
Error out in case of write errors in probe and notify the user.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
[Guenter Roeck: Fixed multi-line comment style]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
All devices supported by ina2xx are bidirectional and report the
measured shunt voltage and power values as a signed 16 bit, but the
current driver implementation caches all registers as u16, leading
to an incorrect sign extension when reporting to userspace in
ina2xx_get_value().
This patch fixes the problem by casting the signed registers to s16.
Tested on an INA219.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Also introduce dev variable in probe function to simplify access
to client->dev, and use new macro ATTRIBUTE_GROUPS to declare
attribute groups.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adding another way that is device tree to pass the shunt resistor
value to driver except for platform data.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
[Guenter Roeck: Added missing of.h include]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use the module_i2c_driver() macro to make the code smaller
and a bit simpler.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Many hwmon drivers use jiffies but omit the inclusion of the header
file. Fix that, and also fix one driver which was including the header
file but didn't need it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Luca Tettamanti <kronos.it@gmail.com>
Cc: Marc Hulsman <m.hulsman@tudelft.nl>
Cc: Rudolf Marek <r.marek@assembler.cz>
INA220 is register compatible to INA219, and INA230 is register compatible to
INA226, so all we need to do is to add name aliases for those two chips.
Cc: Lothar Felten <l-felten@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Replace per-device initialization and per-device calculation code with
per-device configuration data, which is then used to configure the chip and
perform calculations based on that data.
This patch reduces code size by more than 400 bytes on x86_64.
Cc: Lothar Felten <l-felten@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
The driver uses be16_to_cpu and cpu_to_be16 to convert data in SMBus word
operations from chip to host byte order. However, the data passed from and to
the SMBus word API functions is in host byte order, not in chip byte order.
Conversion should therefore use swab16 instead of be16 to change the byte order.
Replace driver internal word conversion functions with SMBus API functions to
solve the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org # 3.5+
Acked-by: Jean Delvare <khali@linux-fr.org>
Add support for the Texas Instruments INA219 and INA226 power monitors.
Signed-off-by: Lothar Felten <l-felten@ti.com>
[guenter.roeck@ericsson.com: formatting cleanup; check for smbus word data;
select PGA=8 for INA219]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Lothar Felten