Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Instead of just printing "status updated from 1 to 2", make those enum
numbers immediately readable.
v2: Also patch output_poll_execute() (Daniel Vetter)
v3: Use drm_get_connector_status_name (Ville Syrjälä)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (for v1)
Signed-off-by: Dave Airlie <airlied@redhat.com>
We forget to call dev_put() on error path in xfrm6_fill_dst(),
its caller doesn't handle this.
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a hole in struct ip6_tnl_parm2, so we have to
zero the struct on stack before copying it to user-space.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 82dc3c63c6 ("net: introduce NAPI_POLL_WEIGHT")
we warn drivers when they use napi weight higher than NAPI_POLL_WEIGHT,
but virtio_net still uses 128 by default. This patch makes its default
value to NAPI_POLL_WEIGHT.
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix EMAC soft reset on 460EX/GT to select the right PHY clock source
before and after the soft reset.
EMAC with PHY should use the clock from PHY during soft reset.
EMAC without PHY should use the internal clock during soft reset.
PPC460EX/GT Embedded Processor Advanced User's Manual
section 28.10.1 Mode Register 0 (EMACx_MR0) states:
Note: The PHY must provide a TX Clk in order to perform a soft reset
of the EMAC. If none is present, select the internal clock
(SDR0_ETH_CFG[EMACx_PHY_CLK] = 1).
After a soft reset, select the external clock.
Without the fix, 460EX/GT-based boards with RGMII PHYs attached to
EMACs experience EMAC interrupt storm and system watchdog reset when
issuing "ifconfig eth0 down" + "ifconfig eth0 up" a few times.
The system enters endless loop of serving emac_irq() with EMACx_ISR
register stuck at value 0x10000000 (Rx parity error).
With the fix, the above issue is no longer observed.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver wrongly claimed I/O ports at an address returned by pci_iomap() --
even if it was passed an MMIO address. Fix this by claiming/releasing all PCI
resources in the PCI driver's probe()/remove() methods instead and get rid of
'must_free_region' flag weirdness (why would Cardbus claim anything for us?).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kprobes up to par with the latest changes to ftrace (multi buffering
and the new function probes).
He also discovered and fixed some bugs in doing so. When pulling in his
patches, I also found a few minor bugs as well and fixed them.
This also includes a compile fix for some archs that select the ring buffer
but not tracing.
I based this off of the last patch you took from me that fixed the merge
conflict error, as that was the commit that had all the changes I needed
for this set of changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJRjYnJAAoJEOdOSU1xswtMg9EH/iFs438FgrNMk2ZdQftmqcqA
cqcactHo1mmoHjAoLZT/oDBjEThhVUuqzMXrFRutSYcTh4PsQEC3arX0mpsC+T12
UEEV/tZS3TXH+GXEyrOit/O3kzntQcDHwJDV4+0n80IrJmw4IDZbnV3R8DWjS6wp
so+dq0A1pwehcG/upgpw1oTKsGv1G/p6vyf968B6W44icHEClLiph4JE2kzE6D3r
fzSpOLaQoBEvwIRf6xRKxi240VqIItXwfG7pwNpPpSC37gRLzm74zGr+Sj93/k1y
pARbZ/5XO7/pcVYQYupErRAoV5in+QMZ67k5G1vQIvyOS9r039catbQf/7PkzcI=
=EZCE
-----END PGP SIGNATURE-----
Merge tag 'trace-fixes-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing/kprobes update from Steven Rostedt:
"The majority of these changes are from Masami Hiramatsu bringing
kprobes up to par with the latest changes to ftrace (multi buffering
and the new function probes).
He also discovered and fixed some bugs in doing so. When pulling in
his patches, I also found a few minor bugs as well and fixed them.
This also includes a compile fix for some archs that select the ring
buffer but not tracing.
I based this off of the last patch you took from me that fixed the
merge conflict error, as that was the commit that had all the changes
I needed for this set of changes."
* tag 'trace-fixes-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing/kprobes: Support soft-mode disabling
tracing/kprobes: Support ftrace_event_file base multibuffer
tracing/kprobes: Pass trace_probe directly from dispatcher
tracing/kprobes: Increment probe hit-count even if it is used by perf
tracing/kprobes: Use bool for retprobe checker
ftrace: Fix function probe when more than one probe is added
ftrace: Fix the output of enabled_functions debug file
ftrace: Fix locking in register_ftrace_function_probe()
tracing: Add helper function trace_create_new_event() to remove duplicate code
tracing: Modify soft-mode only if there's no other referrer
tracing: Indicate enabled soft-mode in enable file
tracing/kprobes: Fix to increment return event probe hit-count
ftrace: Cleanup regex_lock and ftrace_lock around hash updating
ftrace, kprobes: Fix a deadlock on ftrace_regex_lock
ftrace: Have ftrace_regex_write() return either read or error
tracing: Return error if register_ftrace_function_probe() fails for event_enable_func()
tracing: Don't succeed if event_enable_func did not register anything
ring-buffer: Select IRQ_WORK
If NO_DMA=y:
drivers/built-in.o: In function `cfv_destroy_genpool':
drivers/net/caif/caif_virtio.c:364: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `cfv_create_genpool':
drivers/net/caif/caif_virtio.c:397: undefined reference to `dma_alloc_coherent'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Dmitry Tarnyagin <dmitry.tarnyagin@lockless.no>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
If NO_DMA=y:
drivers/built-in.o: In function `macb_free_consistent':
drivers/net/ethernet/cadence/macb.c:878: undefined reference to `dma_free_coherent'
drivers/net/ethernet/cadence/macb.c:883: undefined reference to `dma_free_coherent'
drivers/net/ethernet/cadence/macb.c:888: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `macb_alloc_consistent':
drivers/net/ethernet/cadence/macb.c:905: undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `macb_tx_interrupt':
drivers/net/ethernet/cadence/macb.c:515: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `macb_tx_error_task':
drivers/net/ethernet/cadence/macb.c:457: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `macb_start_xmit':
drivers/net/ethernet/cadence/macb.c:838: undefined reference to `dma_map_single'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If NO_DMA=y:
drivers/built-in.o: In function `at91ether_start':
drivers/net/ethernet/cadence/at91_ether.c:49: undefined reference to `dma_alloc_coherent'
drivers/net/ethernet/cadence/at91_ether.c:60: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `at91ether_interrupt':
drivers/net/ethernet/cadence/at91_ether.c:250: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `at91ether_start_xmit':
drivers/net/ethernet/cadence/at91_ether.c:169: undefined reference to `dma_map_single'
drivers/built-in.o: In function `at91ether_close':
drivers/net/ethernet/cadence/at91_ether.c:145: undefined reference to `dma_free_coherent'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If NO_DMA=y:
drivers/built-in.o: In function `ath9k_beacon_generate':
drivers/net/wireless/ath/ath9k/beacon.c:146: undefined reference to `dma_unmap_single'
drivers/net/wireless/ath/ath9k/beacon.c:174: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/beacon.c:176: undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `ath9k_beacon_remove_slot':
drivers/net/wireless/ath/ath9k/beacon.c:252: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_descdma_setup':
drivers/net/wireless/ath/ath9k/init.c:382: undefined reference to `dmam_alloc_coherent'
drivers/built-in.o: In function `ath_edma_get_buffers':
drivers/net/wireless/ath/ath9k/recv.c:616: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `ath_get_next_rx_buf':
drivers/net/wireless/ath/ath9k/recv.c:740: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `ath_rx_edma_cleanup':
drivers/net/wireless/ath/ath9k/recv.c:176: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_rx_cleanup':
drivers/net/wireless/ath/ath9k/recv.c:340: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_rx_edma_buf_link':
drivers/net/wireless/ath/ath9k/recv.c:122: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `ath_rx_tasklet':
drivers/net/wireless/ath/ath9k/recv.c:1275: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/recv.c:1277: undefined reference to `dma_mapping_error'
drivers/net/wireless/ath/ath9k/recv.c:1283: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_rx_edma_init':
drivers/net/wireless/ath/ath9k/recv.c:226: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/recv.c:229: undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `ath_rx_init':
drivers/net/wireless/ath/ath9k/recv.c:303: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/recv.c:306: undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `ath_tx_complete_buf':
drivers/net/wireless/ath/ath9k/xmit.c:2088: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `ath_txstatus_setup':
drivers/net/wireless/ath/ath9k/xmit.c:2344: undefined reference to `dmam_alloc_coherent'
drivers/built-in.o: In function `ath_tx_set_retry':
drivers/net/wireless/ath/ath9k/xmit.c:307: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `ath_tx_setup_buffer':
drivers/net/wireless/ath/ath9k/xmit.c:1887: undefined reference to `dma_map_single'
drivers/net/wireless/ath/ath9k/xmit.c:1889: undefined reference to `dma_mapping_error'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
If NO_DMA=y:
drivers/built-in.o: In function `dma_free_tx_skbufs':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1141: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `dma_free_rx_skbufs':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1120: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `free_dma_desc_resources':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1159: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `stmmac_init_rx_buffers':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:980: undefined reference to `dma_map_single'
drivers/built-in.o: In function `init_dma_desc_rings':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1015: undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `stmmac_tx_clean':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1250: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `stmmac_rx':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2044: undefined reference to `dma_unmap_single'
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2082: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `stmmac_rx_refill':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1967: undefined reference to `dma_map_single'
drivers/built-in.o: In function `stmmac_xmit':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1845: undefined reference to `dma_map_single'
drivers/built-in.o: In function `skb_frag_dma_map':
include/linux/skbuff.h:2184: undefined reference to `dma_map_page'
drivers/built-in.o: In function `stmmac_jumbo_frm':
drivers/net/ethernet/stmicro/stmmac/ring_mode.c:40: undefined reference to `dma_map_single'
drivers/built-in.o: In function `stmmac_jumbo_frm':
drivers/net/ethernet/stmicro/stmmac/chain_mode.c:48: undefined reference to `dma_map_single'
drivers/net/ethernet/stmicro/stmmac/chain_mode.c:55: undefined reference to `dma_map_single'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
If NO_DMA=y:
drivers/built-in.o: In function `xgmac_xmit':
drivers/net/ethernet/calxeda/xgmac.c:1102: undefined reference to `dma_mapping_error'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
We have seen multiple NULL dereferences in __inet6_lookup_established()
After analysis, I found that inet6_sk() could be NULL while the
check for sk_family == AF_INET6 was true.
Bug was added in linux-2.6.29 when RCU lookups were introduced in UDP
and TCP stacks.
Once an IPv6 socket, using SLAB_DESTROY_BY_RCU is inserted in a hash
table, we no longer can clear pinet6 field.
This patch extends logic used in commit fcbdf09d96
("net: fix nulls list corruptions in sk_prot_alloc")
TCP/UDP/UDPLite IPv6 protocols provide their own .clear_sk() method
to make sure we do not clear pinet6 field.
At socket clone phase, we do not really care, as cloning the parent (non
NULL) pinet6 is not adding a fatal race.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if macvlan in passthru mode is created and data are rxed and
you remove this device, following panic happens:
NULL pointer dereference at 0000000000000198
IP: [<ffffffffa0196058>] macvlan_handle_frame+0x153/0x1f7 [macvlan]
I'm using following script to trigger this:
<script>
while [ 1 ]
do
ip link add link e1 name macvtap0 type macvtap mode passthru
ip link set e1 up
ip link set macvtap0 up
IFINDEX=`ip link |grep macvtap0 | cut -f 1 -d ':'`
cat /dev/tap$IFINDEX >/dev/null &
ip link del dev macvtap0
done
</script>
I run this script while "ping -f" is running on another machine to send
packets to e1 rx.
Reason of the panic is that list_first_entry() is blindly called in
macvlan_handle_frame() even if the list was empty. vlan is set to
incorrect pointer which leads to the crash.
I'm fixing this by protecting port->vlans list by rcu and by preventing
from getting incorrect pointer in case the list is empty.
Introduced by: commit eb06acdc85 "macvlan: Introduce 'passthru' mode to takeover the underlying device"
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- fix parsing of user typed protocol string to avoid random memory access in
some cases
- check pskb_trim_rcsum() return value
- prevent DAT from sending ARP replies when not needed
- reorder the main clean up routine to prevent race conditions
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=n0yL
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge
Included changes:
- fix parsing of user typed protocol string to avoid random memory access in
some cases
- check pskb_trim_rcsum() return value
- prevent DAT from sending ARP replies when not needed
- reorder the main clean up routine to prevent race conditions
Signed-off-by: David S. Miller <davem@davemloft.net>
- More fixes in the vCPU PVHVM hotplug path.
- Add more documentation.
- Fix various ARM related issues in the Xen generic drivers.
- Updates in the xen-pciback driver per Bjorn's updates.
- Mask the x2APIC feature for PV guests.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQEcBAABAgAGBQJRjPL5AAoJEFjIrFwIi8fJdlIIANXawH+B+aFbqsFSKOOh76XN
smgICU78SVzKpW9WAPYK7YFqSdNN4AleGC2Mn2lSkiaqgciRyDb9Yt+OSMMts2Xn
ZVbFkGhEKR+DtZfTKo9YgsGatul/McTiVEkuuli+aN5dql3WXDLAaA+/b9bO3ohh
TCWtWNuSCGmlfDoJET2je+J6CgKvCErH3fvzKNxgYxytcGhAvxoVK/lC4d3pnq/m
wQUAIcF8XYENqC2m1WDR0OGveAB0Me0j9g+UkQS+TzqA8GPmxC4aptjkroFYhOz6
8nZp+LanimmTI6olVioWEXkCr5+dxb058jQKwncQfonFpl58RS0qUrz5zoe3etU=
=h9SX
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.10-rc0-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
- More fixes in the vCPU PVHVM hotplug path.
- Add more documentation.
- Fix various ARM related issues in the Xen generic drivers.
- Updates in the xen-pciback driver per Bjorn's updates.
- Mask the x2APIC feature for PV guests.
* tag 'stable/for-linus-3.10-rc0-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pci: Used cached MSI-X capability offset
xen/pci: Use PCI_MSIX_TABLE_BIR, not PCI_MSIX_FLAGS_BIRMASK
xen: clear IRQ_NOAUTOEN and IRQ_NOREQUEST
xen: mask x2APIC feature in PV
xen: SWIOTLB is only used on x86
xen/spinlock: Fix check from greater than to be also be greater or equal to.
xen/smp/pvhvm: Don't point per_cpu(xen_vpcu, 33 and larger) to shared_info
xen/vcpu: Document the xen_vcpu_info and xen_vcpu
xen/vcpu/pvhvm: Fix vcpu hotplugging hanging.
EXPORT_SYMBOL and inline directives are contradictory to each other.
The patch fixes this inconsistency.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Denis Efremov <yefremov.denis@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure that the following steps are taken:
- drop packets sent by the VF with vlan tag
- block packets with vlan tag which are steered to the VF
- drop/block tagged packets when the policy is priority-tagged
- make sure VLAN stripping for received packets is set
- make sure force UP bit for the VF QP is set
Use enum values for all the above instead of numerical bit offsets.
Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commits e6b6a23 "net/mlx4: Add VF MAC spoof checking support" and
3f7fb021 "net/mlx4: Add set VF default vlan ID and priority support"
missed reporting in the device capabilities dump when these features
are actually supported. Also two too noisy debug messages which produce
message on every QP opened by a VF, were left in the code, fix that.
Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4c09eed (net: fec: Enable imx6 enet checksum acceleration.)
enables hardware checksum acceleration unconditionally for all fec
variants. This is inappropriate, because some variants like imx5 have
no such support on hardware. Consequently, fec is broken on these
platforms. Fix it by enabling hardware checksum only on imx6q-fec type
of controllers.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 4eec708d26.
Multiple users have reported crashes which is apparently caused by
this commit. Thanks to Dmitry Monakhov for bisecting it.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: Dmitry Monakhov <dmonakhov@openvz.org>
Cc: Jan Kara <jack@suse.cz>
Shahed Shaikh says:
====================
This patch series has following bug fixes:
* Fix a bug in unicast MAC address setting in adapter.
Driver was not deleting older unicast MAC while adding new one.
* Fix an ethtool stats string array by adding missing string entry
and fix a typo.
* Fix module paramter description. Bracket ')' was missing.
* Fix port status provided though 'ethtool <device>' for 83xx adapter.
* Fix reset recovery path in case of transmit timeout.
* Fix reset recovery during diagnostic tests by preserving
current device status information.
* Fix mailbox response handling. Driver was not maintaining poll time properly.
* Fix validation of link event command.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
o VF driver that has enabled asynchronous link events
may not set BIT_8 in the request, if it does not require
link state in the response.
Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Fix mailbox response poll time to maximum 5 seconds which
includes mailbox response time as well as time required for
processing AEN if any.
o Driver need to read firmware control mailbox register instead
of host control mailbox register.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o In order to perform reset recovery during diagnostics tests,
current device status information need to be preserved.
This patch makes the required changes in diagnostics routines
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o When transmit timeout happens, recovery attempt should start with
adapter soft reset. If soft reset fails to resume traffic, firmware
dump will be collected and driver will perform a hard reset of the
adapter. Reset recovery on 83xx was failing after a hard reset.
This patch fixes that issue.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Fix display for interface while using 'ethtool <device>' for 83xx adapter
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Add missing information in ethtool statistics information array.
o Fix the typo in the statistics information string.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Delete previous unicast MAC which is already programmed
in adapter before setting new unicast MAC
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the final round of SCSI patches for the merge window. It consists
mostly of driver updates (bnx2fc, ibmfc, fnic, lpfc, be2iscsi, pm80xx, qla4x
and ipr). There's also the power management updates that complete the patches
in Jens' tree, an iscsi refcounting problem fix from the last pull, some dif
handling in scsi_debug fixes, a few nice code cleanups and an error handling
busy bug fix.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRjQsqAAoJEDeqqVYsXL0MayMH/iDncN0swy/Y2Pfh31YHRcvG
pPTsx/WgQogg5WDeG1XRPmgDJBmJKeSO7OcIZ/AWz+8BJkZbDLfdSp9ugg8ZrrsN
yAa3lZoOfxhf43AEaUpgORHGj39O+QfoLq3mdo44A57ro30YotIaMvCiqv+baPSL
Z8K7O/TmmHmOeir3Gl05qrO6PKvQkNnHYZoF1lBiHypUJk51cuTmHrfY6mb2ktXc
7aElSXSbpUcqQQ8QHnXO/3r6VPkYjhznvo8q8rcLvqQqRnTdLF5Su8vDuyMbbJcU
svu30wRaBik3XvIfppGhukrYeU5ooj13zZAUY9NIf2vc2wjpMUlRNNZ0uSsHzOw=
=6cOg
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull second SCSI update from James "Jaj B" Bottomley:
"This is the final round of SCSI patches for the merge window. It
consists mostly of driver updates (bnx2fc, ibmfc, fnic, lpfc,
be2iscsi, pm80xx, qla4x and ipr).
There's also the power management updates that complete the patches in
Jens' tree, an iscsi refcounting problem fix from the last pull, some
dif handling in scsi_debug fixes, a few nice code cleanups and an
error handling busy bug fix."
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (92 commits)
[SCSI] qla2xxx: Update firmware link in Kconfig file.
[SCSI] iscsi class, qla4xxx: fix sess/conn refcounting when find fns are used
[SCSI] sas: unify the pointlessly separated enums sas_dev_type and sas_device_type
[SCSI] pm80xx: thermal, sas controller config and error handling update
[SCSI] pm80xx: NCQ error handling changes
[SCSI] pm80xx: WWN Modification for PM8081/88/89 controllers
[SCSI] pm80xx: Changed module name and debug messages update
[SCSI] pm80xx: Firmware flash memory free fix, with addition of new memory region for it
[SCSI] pm80xx: SPC new firmware changes for device id 0x8081 alone
[SCSI] pm80xx: Added SPCv/ve specific hardware functionalities and relevant changes in common files
[SCSI] pm80xx: MSI-X implementation for using 64 interrupts
[SCSI] pm80xx: Updated common functions common for SPC and SPCv/ve
[SCSI] pm80xx: Multiple inbound/outbound queue configuration
[SCSI] pm80xx: Added SPCv/ve specific ids, variables and modify for SPC
[SCSI] lpfc: fix up Kconfig dependencies
[SCSI] Handle MLQUEUE busy response in scsi_send_eh_cmnd
[SCSI] sd: change to auto suspend mode
[SCSI] sd: use REQ_PM in sd's runtime suspend operation
[SCSI] qla4xxx: Fix iocb_cnt calculation in qla4xxx_send_mbox_iocb()
[SCSI] ufs: Correct the expected data transfersize
...
Pull idle update from Len Brown:
"Add support for new Haswell-ULT CPU idle power states"
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
intel_idle: initial C8, C9, C10 support
tools/power turbostat: display C8, C9, C10 residency
Pull audit changes from Eric Paris:
"Al used to send pull requests every couple of years but he told me to
just start pushing them to you directly.
Our touching outside of core audit code is pretty straight forward. A
couple of interface changes which hit net/. A simple argument bug
calling audit functions in namei.c and the removal of some assembly
branch prediction code on ppc"
* git://git.infradead.org/users/eparis/audit: (31 commits)
audit: fix message spacing printing auid
Revert "audit: move kaudit thread start from auditd registration to kaudit init"
audit: vfs: fix audit_inode call in O_CREAT case of do_last
audit: Make testing for a valid loginuid explicit.
audit: fix event coverage of AUDIT_ANOM_LINK
audit: use spin_lock in audit_receive_msg to process tty logging
audit: do not needlessly take a lock in tty_audit_exit
audit: do not needlessly take a spinlock in copy_signal
audit: add an option to control logging of passwords with pam_tty_audit
audit: use spin_lock_irqsave/restore in audit tty code
helper for some session id stuff
audit: use a consistent audit helper to log lsm information
audit: push loginuid and sessionid processing down
audit: stop pushing loginid, uid, sessionid as arguments
audit: remove the old depricated kernel interface
audit: make validity checking generic
audit: allow checking the type of audit message in the user filter
audit: fix build break when AUDIT_DEBUG == 2
audit: remove duplicate export of audit_enabled
Audit: do not print error when LSMs disabled
...
Currently, race conditions exist in the handling of TLB interruptions in
entry.S. In particular, dirty bit updates can be lost if an accessed
interruption occurs just after the dirty bit interruption on a different
cpu. Lost dirty bit updates result in user pages not being flushed and
general system instability. This change adds lock and unlock macros to
synchronize all PTE and TLB updates done in entry.S. As a result,
userspace stability is significantly improved.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
This patch fixes few build issues which were introduced with the last
irq stack patch, e.g. the combination of stack overflow check and irq
stack.
Furthermore we now do proper locking and change the irq bh handler
to use the irq stack as well.
In /proc/interrupts one now can monitor how huge the irq stack has grown
and how often it was preferred over the kernel stack.
IRQ stacks are now enabled by default just to make sure that we not
overflow the kernel stack by accident.
Signed-off-by: Helge Deller <deller@gmx.de>
John W. Linville says:
====================
Here is a batch of fixes intended for the 3.10 stream.
Amitkumar Karwar provides an mwifiex fix to plug a memory leak when
the driver is unloaded.
Bing Zhao brings an mwifiex fix for some flag handling that leads to
log spam and an unusable interface.
Daniel Drake offers an mwifiex fix for multicast filter setup, to
correctly implement wakeup behaviour for multicast WOL.
Felix Fietkau fixes an ath9k problem that produces logspam and keycache
errors due to a bad return code.
Stanislaw Gruszka produces an fix for a WARNING from ath5k, and an
iwl4965 workaround to stop advertising a feature that doesn't work with
the current mac80211 implementation.
Sujith Manoharan gives us an ath9k fix to reprogram the HW beacon timers
after a TSF update, and an initvals fix for the AR9565 device.
Thommy Jakobsson fixes an rx descriptor underrun on b43.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull nfsd fixes from Bruce Fields:
"Small fixes for two bugs and two warnings"
* 'for-3.10' of git://linux-nfs.org/~bfields/linux:
nfsd: fix oops when legacy_recdir_name_error is passed a -ENOENT error
SUNRPC: fix decoding of optional gss-proxy xdr fields
SUNRPC: Refactor gssx_dec_option_array() to kill uninitialized warning
nfsd4: don't allow owner override on 4.1 CLAIM_FH opens
Pull x86 platform drivers from Matthew Garrett:
"Small set of updates, mainly trivial bugfixes and some small updates
to deal with newer hardware.
There's also a new driver that allows qemu guests to notify the
hypervisor that they've just paniced, which seems useful."
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86:
Add support for fan button on Ideapad Z580
pvpanic: pvpanic device driver
asus-nb-wmi: set wapf=4 for ASUSTeK COMPUTER INC. X75A
drivers: platform: x86: Use PTR_RET function
sony-laptop: SVS151290S kbd backlight and gfx switch support
hp-wmi: add more definitions for new event_id's
dell-laptop: Fix krealloc() misuse in parse_da_table()
hp_accel: Ignore the error from lis3lv02d_poweron() at resume
dell: add new dell WMI format for the AIO machines
Pull stray syscall bits from Al Viro:
"Several syscall-related commits that were missing from the original"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
switch compat_sys_sysctl to COMPAT_SYSCALL_DEFINE
unicore32: just use mmap_pgoff()...
unify compat fanotify_mark(2), switch to COMPAT_SYSCALL_DEFINE
x86, vm86: fix VM86 syscalls: use SYSCALL_DEFINEx(...)
available by moving to the ablkcipher crypto API. The improvement is more
apparent on faster storage devices. There's no noticeable change when hardware
crypto is not available.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=3EhP
-----END PGP SIGNATURE-----
Merge tag 'ecryptfs-3.10-rc1-ablkcipher' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs
Pull eCryptfs update from Tyler Hicks:
"Improve performance when AES-NI (and most likely other crypto
accelerators) is available by moving to the ablkcipher crypto API.
The improvement is more apparent on faster storage devices.
There's no noticeable change when hardware crypto is not available"
* tag 'ecryptfs-3.10-rc1-ablkcipher' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
eCryptfs: Use the ablkcipher crypto API
- Two krealloc() abuse fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iEYEABECAAYFAlGLydsACgkQdwG7hYl686O3ZwCfYIJUdE/VADo53j3SwDbCEa15
pMgAnA13t6dKgC74Xqk5dd65KKaw64WB
=nbL9
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20130509' of git://git.infradead.org/~dwmw2/random-2.6
Pull misc fixes from David Woodhouse:
"This is some miscellaneous cleanups that don't really belong anywhere
else (or were ignored), that have been sitting in linux-next for some
time. Two of them are fixes resulting from my audit of krealloc()
usage that don't seem to have elicited any response when I posted
them, and the other three are patches from Artem removing dead code."
* tag 'for-linus-20130509' of git://git.infradead.org/~dwmw2/random-2.6:
pcmcia: remove RPX board stuff
m68k: remove rpxlite stuff
pcmcia: remove Motorola MBX860 support
params: Fix potential memory leak in add_sysfs_param()
dell-laptop: Fix krealloc() misuse in parse_da_table()
Pull kvm fixes from Gleb Natapov:
"Most of the fixes are in the emulator since now we emulate more than
we did before for correctness sake we see more bugs there, but there
is also an OOPS fixed and corruption of xcr0 register."
* tag 'kvm-3.10-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: emulator: emulate SALC
KVM: emulator: emulate XLAT
KVM: emulator: emulate AAM
KVM: VMX: fix halt emulation while emulating invalid guest sate
KVM: Fix kvm_irqfd_init initialization
KVM: x86: fix maintenance of guest/host xcr0 state
provisioning target to be extended easily; allow WRITE SAME on
multipath devices; an assortment of little fixes and clean-ups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YXMj
-----END PGP SIGNATURE-----
Merge tag 'dm-3.10-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull device-mapper updates from Alasdair Kergon:
"Allow devices that hold metadata for the device-mapper thin
provisioning target to be extended easily; allow WRITE SAME on
multipath devices; an assortment of little fixes and clean-ups."
* tag 'dm-3.10-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm: (21 commits)
dm cache: set config value
dm cache: move config fns
dm thin: generate event when metadata threshold passed
dm persistent metadata: add space map threshold callback
dm persistent data: add threshold callback to space map
dm thin: detect metadata device resizing
dm persistent data: support space map resizing
dm thin: open dev read only when possible
dm thin: refactor data dev resize
dm cache: replace memcpy with struct assignment
dm cache: fix typos in comments
dm cache policy: fix description of lookup fn
dm: document iterate_devices
dm persistent data: fix error message typos
dm cache: tune migration throttling
dm mpath: enable WRITE SAME support
dm table: fix write same support
dm bufio: avoid a possible __vmalloc deadlock
dm snapshot: fix error return code in snapshot_ctr
dm cache: fix error return code in cache_create
...
Pull HID fixes from Jiri Kosina:
- fix usage of sleeping lock in atomic context from Jiri Kosina
- build fix for hid-steelseries under certain .config setups by Simon Wood
- simple mismerge fix from Fernando Luis Vázquez Cao
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: debug: fix RCU preemption issue
HID: hid-steelseries fix led class build issue
HID: reintroduce fix-up for certain Sony RF receivers
Lespiau, Damien