Variants of proc_create{,_data} that directly take a struct seq_operations
argument and drastically reduces the boilerplate code in the callers.
All trivial callers converted over.
Signed-off-by: Christoph Hellwig <hch@lst.de>
In the quest to remove all stack VLA usage from the kernel[1], this
allocates the return code buffers before starting jiffie timers, rather
than using stack space for the array. Additionally cleans up some exit
paths and make sure that the num_mb module_param() is used only once
per execution to avoid possible races in the value changing.
[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In preparation of adding support for the SIMD based arm64 implementation
of arm64, which requires a fallback to non-SIMD code when invoked in
certain contexts, expose the generic SM4 encrypt and decrypt routines
to other drivers.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Enable CryptoCell support for hardware keys.
Hardware keys are regular AES keys loaded into CryptoCell internal memory
via firmware, often from secure boot ROM or hardware fuses at boot time.
As such, they can be used for enc/dec purposes like any other key but
cannot (read: extremely hard to) be extracted since since they are not
available anywhere in RAM during runtime.
The mechanism has some similarities to s390 secure keys although the keys
are not wrapped or sealed, but simply loaded offline. The interface was
therefore modeled based on the s390 secure keys support.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There is no need to assign an error value to 'ret' prior
to calling mpi_read_raw_from_sgl() because in the case
of error the 'ret' variable will be assigned to the error
code inside the if block.
In the case of non failure, 'ret' will be overwritten
immediately after, so remove the unneeded assignment.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The following error is triggered by the ThunderX ZIP driver
if the testmanager is enabled:
[ 199.069437] ThunderX-ZIP 0000:03:00.0: Found ZIP device 0 177d:a01a on Node 0
[ 199.073573] alg: comp: Compression test 1 failed for deflate-generic: output len = 37
The reason for this error is the verification of the compression
results. Verifying the compression result only works if all
algorithm parameters are identical, in this case to the software
implementation.
Different compression engines like the ThunderX ZIP coprocessor
might yield different compression results by tuning the
algorithm parameters. In our case the compressed result is
shorter than the test vector.
We should not forbid different compression results but only
check that compression -> decompression yields the same
result. This is done already in the acomp test. Do something
similar for test_comp().
Signed-off-by: Mahipal Challa <mchalla@cavium.com>
Signed-off-by: Balakrishna Bhamidipati <bbhamidipati@cavium.com>
[jglauber@cavium.com: removed unrelated printk changes, rewrote commit msg,
fixed whitespace and unneeded initialization]
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In preparation for the removal of VLAs[1] from crypto code.
We create 2 new compile-time constants: all ciphers implemented
in Linux have a block size less than or equal to 16 bytes and
the most demanding hw require 16 bytes alignment for the block
buffer.
We also enforce these limits in crypto_check_alg when a new
cipher is registered.
[1] http://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Signed-off-by: Salvatore Mesoraca <s.mesoraca16@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In crypto_authenc_esn_setkey we save pointers to the authenc keys
in a local variable of type struct crypto_authenc_keys and we don't
zeroize it after use. Fix this and don't leak pointers to the
authenc keys.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In crypto_authenc_setkey we save pointers to the authenc keys in
a local variable of type struct crypto_authenc_keys and we don't
zeroize it after use. Fix this and don't leak pointers to the
authenc keys.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Adds zstd support to crypto and scompress. Only supports the default
level.
Previously we held off on this patch, since there weren't any users.
Now zram is ready for zstd support, but depends on CONFIG_CRYPTO_ZSTD,
which isn't defined until this patch is in. I also see a patch adding
zstd to pstore [0], which depends on crypto zstd.
[0] lkml.kernel.org/r/9c9416b2dff19f05fb4c35879aaa83d11ff72c92.1521626182.git.geliangtang@gmail.com
Signed-off-by: Nick Terrell <terrelln@fb.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
On the quest to remove all VLAs from the kernel[1], this avoids VLAs
by just using the maximum allocation size (4 bytes) for stack arrays.
All the VLAs in ecc were either 3 or 4 bytes (or a multiple), so just
make it 4 bytes all the time. Initialization routines are adjusted to
check that ndigits does not end up larger than the arrays.
This includes a removal of the earlier attempt at this fix from
commit a963834b4742 ("crypto/ecc: Remove stack VLA usage")
[1] https://lkml.org/lkml/2018/3/7/621
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
During freeing of the internal buffers used by the DRBG, set the pointer
to NULL. It is possible that the context with the freed buffers is
reused. In case of an error during initialization where the pointers
do not yet point to allocated memory, the NULL value prevents a double
free.
Cc: stable@vger.kernel.org
Fixes: 3cfc3b9721 ("crypto: drbg - use aligned buffers")
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Reported-by: syzbot+75397ee3df5c70164154@syzkaller.appspotmail.com
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Commit eb02c38f01 ("crypto: api - Keep failed instances alive") is
making allocating crypto transforms sometimes fail with ELIBBAD, when
multiple processes try to access encrypted files with fscrypt for the
first time since boot. The problem is that the "request larval" for the
algorithm is being mistaken for an algorithm which failed its tests.
Fix it by only returning ELIBBAD for "non-larval" algorithms. Also
don't leak a reference to the algorithm.
Fixes: eb02c38f01 ("crypto: api - Keep failed instances alive")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
- pass HOSTLDFLAGS when compiling single .c host programs
- build genksyms lexer and parser files instead of using shipped
versions
- rename *-asn1.[ch] to *.asn1.[ch] for suffix consistency
- let the top .gitignore globally ignore artifacts generated by
flex, bison, and asn1_compiler
- let the top Makefile globally clean artifacts generated by
flex, bison, and asn1_compiler
- use safer .SECONDARY marker instead of .PRECIOUS to prevent
intermediate files from being removed
- support -fmacro-prefix-map option to make __FILE__ a relative path
- fix # escaping to prepare for the future GNU Make release
- clean up deb-pkg by using debian tools instead of handrolled
source/changes generation
- improve rpm-pkg portability by supporting kernel-install as a
fallback of new-kernel-pkg
- extend Kconfig listnewconfig target to provide more information
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tD6R
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- pass HOSTLDFLAGS when compiling single .c host programs
- build genksyms lexer and parser files instead of using shipped
versions
- rename *-asn1.[ch] to *.asn1.[ch] for suffix consistency
- let the top .gitignore globally ignore artifacts generated by flex,
bison, and asn1_compiler
- let the top Makefile globally clean artifacts generated by flex,
bison, and asn1_compiler
- use safer .SECONDARY marker instead of .PRECIOUS to prevent
intermediate files from being removed
- support -fmacro-prefix-map option to make __FILE__ a relative path
- fix # escaping to prepare for the future GNU Make release
- clean up deb-pkg by using debian tools instead of handrolled
source/changes generation
- improve rpm-pkg portability by supporting kernel-install as a
fallback of new-kernel-pkg
- extend Kconfig listnewconfig target to provide more information
* tag 'kbuild-v4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: extend output of 'listnewconfig'
kbuild: rpm-pkg: use kernel-install as a fallback for new-kernel-pkg
Kbuild: fix # escaping in .cmd files for future Make
kbuild: deb-pkg: split generating packaging and build
kbuild: use -fmacro-prefix-map to make __FILE__ a relative path
kbuild: mark $(targets) as .SECONDARY and remove .PRECIOUS markers
kbuild: rename *-asn1.[ch] to *.asn1.[ch]
kbuild: clean up *-asn1.[ch] patterns from top-level Makefile
.gitignore: move *-asn1.[ch] patterns to the top-level .gitignore
kbuild: add %.dtb.S and %.dtb to 'targets' automatically
kbuild: add %.lex.c and %.tab.[ch] to 'targets' automatically
genksyms: generate lexer and parser during build instead of shipping
kbuild: clean up *.lex.c and *.tab.[ch] patterns from top-level Makefile
.gitignore: move *.lex.c *.tab.[ch] patterns to the top-level .gitignore
kbuild: use HOSTLDFLAGS for single .c executables
These are the main MIPS changes for 4.17. Rough overview:
(1) generic platform: Add support for Microsemi Ocelot SoCs
(2) crypto: Add CRC32 and CRC32C HW acceleration module
(3) Various cleanups and misc improvements
Miscellaneous:
- Hang more efficiently on halt/powerdown/restart
- pm-cps: Block system suspend when a JTAG probe is present
- Expand make help text for generic defconfigs
- Refactor handling of legacy defconfigs
- Determine the entry point from the ELF file header to fix microMIPS
for certain toolchains
- Introduce isa-rev.h for MIPS_ISA_REV and use to simplify other code
Minor cleanups:
- DTS: boston/ci20: Unit name cleanups and correction
- kdump: Make the default for PHYSICAL_START always 64-bit
- Constify gpio_led in Alchemy, AR7, and TXX9
- Silence a couple of W=1 warnings
- Remove duplicate includes
Platform support:
ath79:
- Fix AR724X_PLL_REG_PCIE_CONFIG offset
BCM47xx:
- FIRMWARE: Use mac_pton() for MAC address parsing
- Add Luxul XAP1500/XWR1750 WiFi LEDs
- Use standard reset button for Luxul XWR-1750
BMIPS:
- Enable CONFIG_BRCMSTB_PM in bmips_stb_defconfig for build coverage
- Add STB PM, wake-up timer, watchdog DT nodes
Generic platform:
- Add support for Microsemi Ocelot
- dt-bindings: Add vendor prefix for Microsemi Corporation
- dt-bindings: Add bindings for Microsemi SoCs
- Add ocelot SoC & PCB123 board DTS files
- MAINTAINERS: Add entry for Microsemi MIPS SoCs
- Enable crc32-mips on r6 configs
Octeon:
- Drop '.' after newlines in printk calls
ralink:
- pci-mt7621: Enable PCIe on MT7688
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEd80NauSabkiESfLYbAtpk944dnoFAlrL1tMACgkQbAtpk944
dnpkhg//UnKOmj4xiQf5ik4XjSDHo2dcUzQKPLq/grzpc9yC2I6bgJ32gcQnD/rw
x2f64DAjmbIJEY/hCGLEOH82/SqU5vF5gI+BtSKE6Ti28dyQH68pvyHRYIZBFx62
WRYAf50Spa/q/bOJYv4/eTqjEc7FPMaUll3kH5NMiBB3X5bIeq3w+x78YBKjAqPB
IJgHF/JnlpD8UvQ0RCl1fIXhkRYeNuTyiAseVI3ygAqbMFMGkTevePWl82D+pWuo
W9BFaliNt/9TNgq5/L91a/uhSuo6INRls1tFQT9cPa6n4GJxLpUtO7a3v4Xgaukj
TeXTkXZl4PEUfeTA3cVaXrENTN4sCwThkxvrKwefbUBiIa+/TDi/Wgxi3n+rKwi2
Vu4V36uxnO/vNU7Sgp/jHdRJyxw06GfRy55MvToFlk1S25Gwt6zW2O0o8nAHwCDW
zvoRfSkasElKwnM3zKR/mrdDn7qPulFfiyWyKuuY3bIXsaTnItO1JJ/rbgKuIXr7
lo0eVZ7GhuWfuLCEHZ99rWsGz0SjuQQIb4c6faNELp6gTwIpz9bbsOHRuajvfoSF
8jmPjUocbaRR0odyFBqsejwBmeebDoeIZljzD50ImSoYftEMgRoQ448mIm0EuWVU
KY+85MIeK5zwWXKd4VBexgLvPggGURaOEEXKisgvoE3NjCuO2nw=
=4vUc
-----END PGP SIGNATURE-----
Merge tag 'mips_4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips
Pull MIPS updates from James Hogan:
"These are the main MIPS changes for 4.17. Rough overview:
(1) generic platform: Add support for Microsemi Ocelot SoCs
(2) crypto: Add CRC32 and CRC32C HW acceleration module
(3) Various cleanups and misc improvements
More detailed summary:
Miscellaneous:
- hang more efficiently on halt/powerdown/restart
- pm-cps: Block system suspend when a JTAG probe is present
- expand make help text for generic defconfigs
- refactor handling of legacy defconfigs
- determine the entry point from the ELF file header to fix microMIPS
for certain toolchains
- introduce isa-rev.h for MIPS_ISA_REV and use to simplify other code
Minor cleanups:
- DTS: boston/ci20: Unit name cleanups and correction
- kdump: Make the default for PHYSICAL_START always 64-bit
- constify gpio_led in Alchemy, AR7, and TXX9
- silence a couple of W=1 warnings
- remove duplicate includes
Platform support:
Generic platform:
- add support for Microsemi Ocelot
- dt-bindings: Add vendor prefix for Microsemi Corporation
- dt-bindings: Add bindings for Microsemi SoCs
- add ocelot SoC & PCB123 board DTS files
- MAINTAINERS: Add entry for Microsemi MIPS SoCs
- enable crc32-mips on r6 configs
ath79:
- fix AR724X_PLL_REG_PCIE_CONFIG offset
BCM47xx:
- firmware: Use mac_pton() for MAC address parsing
- add Luxul XAP1500/XWR1750 WiFi LEDs
- use standard reset button for Luxul XWR-1750
BMIPS:
- enable CONFIG_BRCMSTB_PM in bmips_stb_defconfig for build coverage
- add STB PM, wake-up timer, watchdog DT nodes
Octeon:
- drop '.' after newlines in printk calls
ralink:
- pci-mt7621: Enable PCIe on MT7688"
* tag 'mips_4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips: (37 commits)
MIPS: BCM47XX: Use standard reset button for Luxul XWR-1750
MIPS: BCM47XX: Add Luxul XAP1500/XWR1750 WiFi LEDs
MIPS: Make the default for PHYSICAL_START always 64-bit
MIPS: Use the entry point from the ELF file header
MAINTAINERS: Add entry for Microsemi MIPS SoCs
MIPS: generic: Add support for Microsemi Ocelot
MIPS: mscc: Add ocelot PCB123 device tree
MIPS: mscc: Add ocelot dtsi
dt-bindings: mips: Add bindings for Microsemi SoCs
dt-bindings: Add vendor prefix for Microsemi Corporation
MIPS: ath79: Fix AR724X_PLL_REG_PCIE_CONFIG offset
MIPS: pci-mt7620: Enable PCIe on MT7688
MIPS: pm-cps: Block system suspend when a JTAG probe is present
MIPS: VDSO: Replace __mips_isa_rev with MIPS_ISA_REV
MIPS: BPF: Replace __mips_isa_rev with MIPS_ISA_REV
MIPS: cpu-features.h: Replace __mips_isa_rev with MIPS_ISA_REV
MIPS: Introduce isa-rev.h to define MIPS_ISA_REV
MIPS: Hang more efficiently on halt/powerdown/restart
FIRMWARE: bcm47xx_nvram: Replace mac address parsing
MIPS: BMIPS: Add Broadcom STB watchdog nodes
...
syzbot reported :
BUG: KMSAN: uninit-value in alg_bind+0xe3/0xd90 crypto/af_alg.c:162
We need to check addr_len before dereferencing sa (or uaddr)
Fixes: bb30b8848c ("crypto: af_alg - whitelist mask and type")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Stephan Mueller <smueller@chronox.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our convention is to distinguish file types by suffixes with a period
as a separator.
*-asn1.[ch] is a different pattern from other generated sources such
as *.lex.c, *.tab.[ch], *.dtb.S, etc. More confusing, files with
'-asn1.[ch]' are generated files, but '_asn1.[ch]' are checked-in
files:
net/netfilter/nf_conntrack_h323_asn1.c
include/linux/netfilter/nf_conntrack_h323_asn1.h
include/linux/sunrpc/gss_asn1.h
Rename generated files to *.asn1.[ch] for consistency.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Pull crypto updates from Herbert Xu:
"API:
- add AEAD support to crypto engine
- allow batch registration in simd
Algorithms:
- add CFB mode
- add speck block cipher
- add sm4 block cipher
- new test case for crct10dif
- improve scheduling latency on ARM
- scatter/gather support to gcm in aesni
- convert x86 crypto algorithms to skcihper
Drivers:
- hmac(sha224/sha256) support in inside-secure
- aes gcm/ccm support in stm32
- stm32mp1 support in stm32
- ccree driver from staging tree
- gcm support over QI in caam
- add ks-sa hwrng driver"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (212 commits)
crypto: ccree - remove unused enums
crypto: ahash - Fix early termination in hash walk
crypto: brcm - explicitly cast cipher to hash type
crypto: talitos - don't leak pointers to authenc keys
crypto: qat - don't leak pointers to authenc keys
crypto: picoxcell - don't leak pointers to authenc keys
crypto: ixp4xx - don't leak pointers to authenc keys
crypto: chelsio - don't leak pointers to authenc keys
crypto: caam/qi - don't leak pointers to authenc keys
crypto: caam - don't leak pointers to authenc keys
crypto: lrw - Free rctx->ext with kzfree
crypto: talitos - fix IPsec cipher in length
crypto: Deduplicate le32_to_cpu_array() and cpu_to_le32_array()
crypto: doc - clarify hash callbacks state machine
crypto: api - Keep failed instances alive
crypto: api - Make crypto_alg_lookup static
crypto: api - Remove unused crypto_type lookup function
crypto: chelsio - Remove declaration of static function from header
crypto: inside-secure - hmac(sha224) support
crypto: inside-secure - hmac(sha256) support
..
When we have an unaligned SG list entry where there is no leftover
aligned data, the hash walk code will incorrectly return zero as if
the entire SG list has been processed.
This patch fixes it by moving onto the next page instead.
Reported-by: Eli Cooper <elicooper@gmx.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The buffer rctx->ext contains potentially sensitive data and should
be freed with kzfree.
Cc: <stable@vger.kernel.org>
Fixes: 700cb3f5fe ("crypto: lrw - Convert to skcipher")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Deduplicate le32_to_cpu_array() and cpu_to_le32_array() by moving them
to the generic header.
No functional change implied.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch reverts commit 9c521a200b ("crypto: api - remove
instance when test failed") and fixes the underlying problem
in a different way.
To recap, prior to the reverted commit, an instance that fails
a self-test is kept around. However, it would satisfy any new
lookups against its name and therefore the system may accumlulate
an unbounded number of failed instances for the same algorithm
name.
The reverted commit fixed it by unregistering the instance. Hoever,
this still does not prevent the creation of the same failed instance
over and over again each time the name is looked up.
This patch fixes it by keeping the failed instance around, just as
we would if it were a normal algorithm. However, the lookup code
has been udpated so that we do not attempt to create another
instance as long as this failed one is still registered. Of course,
you could still force a new creation by deleting the instance from
user-space.
A new error (ELIBBAD) has been commandeered for this purpose and
will be returned when all registered algorithm of a given name
have failed the self-test.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The function crypto_alg_lookup is only usd within the crypto API
and should be not be exported to the modules. This patch marks
it as a static function.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The lookup function in crypto_type was only used for the implicit
IV generators which have been completely removed from the crypto
API.
This patch removes the lookup function as it is now useless.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In order to be able to test yield support under preempt, add a test
vector for CRC-T10DIF that is long enough to take multiple iterations
(and thus possible preemption between them) of the primary loop of the
accelerated x86 and arm64 implementations.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
On the quest to remove all VLAs from the kernel[1], this switches to
a pair of kmalloc regions instead of using the stack. This also moves
the get_random_bytes() after all allocations (and drops the needless
"nbytes" variable).
[1] https://lkml.org/lkml/2018/3/7/621
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Introduce the SM4 cipher algorithms (OSCCA GB/T 32907-2016).
SM4 (GBT.32907-2016) is a cryptographic standard issued by the
Organization of State Commercial Administration of China (OSCCA)
as an authorized cryptographic algorithms for the use within China.
SMS4 was originally created for use in protecting wireless
networks, and is mandated in the Chinese National Standard for
Wireless LAN WAPI (Wired Authentication and Privacy Infrastructure)
(GB.15629.11-2003).
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Apparently the ecdh use case was in bluetooth which always has single
element scatterlists, so the ecdh module was hard coded to expect
them. Now we're using this in TPM, we need multi-element
scatterlists, so remove this limitation.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
TPM security routines require encryption and decryption with AES in
CFB mode, so add it to the Linux Crypto schemes. CFB is basically a
one time pad where the pad is generated initially from the encrypted
IV and then subsequently from the encrypted previous block of
ciphertext. The pad is XOR'd into the plain text to get the final
ciphertext.
https://en.wikipedia.org/wiki/Block_cipher_mode_of_operation#CFB
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
All users of ablk_helper have been converted over to crypto_simd, so
remove ablk_helper.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Now that all users of lrw_crypt() have been removed in favor of the LRW
template wrapping an ECB mode algorithm, remove lrw_crypt(). Also
remove crypto/lrw.h as that is no longer needed either; and fold
'struct lrw_table_ctx' into 'struct priv', lrw_init_table() into
setkey(), and lrw_free_table() into exit_tfm().
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Now that all users of xts_crypt() have been removed in favor of the XTS
template wrapping an ECB mode algorithm, remove xts_crypt().
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Convert the AESNI AVX and AESNI AVX2 implementations of Camellia from
the (deprecated) ablkcipher and blkcipher interfaces over to the
skcipher interface. Note that this includes replacing the use of
ablk_helper with crypto_simd.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Convert the x86 asm implementation of Camellia from the (deprecated)
blkcipher interface over to the skcipher interface.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The XTS template now wraps an ECB mode algorithm rather than the block
cipher directly. Therefore it is now redundant for crypto modules to
wrap their ECB code with generic XTS code themselves via xts_crypt().
Remove the xts-camellia-asm algorithm which did this. Users who request
xts(camellia) and previously would have gotten xts-camellia-asm will now
get xts(ecb-camellia-asm) instead, which is just as fast.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The LRW template now wraps an ECB mode algorithm rather than the block
cipher directly. Therefore it is now redundant for crypto modules to
wrap their ECB code with generic LRW code themselves via lrw_crypt().
Remove the lrw-camellia-asm algorithm which did this. Users who request
lrw(camellia) and previously would have gotten lrw-camellia-asm will now
get lrw(ecb-camellia-asm) instead, which is just as fast.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The LRW template now wraps an ECB mode algorithm rather than the block
cipher directly. Therefore it is now redundant for crypto modules to
wrap their ECB code with generic LRW code themselves via lrw_crypt().
Remove the lrw-camellia-aesni-avx2 algorithm which did this. Users who
request lrw(camellia) and previously would have gotten
lrw-camellia-aesni-avx2 will now get lrw(ecb-camellia-aesni-avx2)
instead, which is just as fast.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The LRW template now wraps an ECB mode algorithm rather than the block
cipher directly. Therefore it is now redundant for crypto modules to
wrap their ECB code with generic LRW code themselves via lrw_crypt().
Remove the lrw-camellia-aesni algorithm which did this. Users who
request lrw(camellia) and previously would have gotten
lrw-camellia-aesni will now get lrw(ecb-camellia-aesni) instead, which
is just as fast.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Convert the x86 asm implementation of Triple DES from the (deprecated)
blkcipher interface over to the skcipher interface.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Convert the x86 asm implementation of Blowfish from the (deprecated)
blkcipher interface over to the skcipher interface.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Convert the AVX implementation of CAST6 from the (deprecated) ablkcipher
and blkcipher interfaces over to the skcipher interface. Note that this
includes replacing the use of ablk_helper with crypto_simd.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The LRW template now wraps an ECB mode algorithm rather than the block
cipher directly. Therefore it is now redundant for crypto modules to
wrap their ECB code with generic LRW code themselves via lrw_crypt().
Remove the lrw-cast6-avx algorithm which did this. Users who request
lrw(cast6) and previously would have gotten lrw-cast6-avx will now get
lrw(ecb-cast6-avx) instead, which is just as fast.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Convert the AVX implementation of CAST5 from the (deprecated) ablkcipher
and blkcipher interfaces over to the skcipher interface. Note that this
includes replacing the use of ablk_helper with crypto_simd.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Convert the AVX implementation of Twofish from the (deprecated)
ablkcipher and blkcipher interfaces over to the skcipher interface.
Note that this includes replacing the use of ablk_helper with
crypto_simd.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The LRW template now wraps an ECB mode algorithm rather than the block
cipher directly. Therefore it is now redundant for crypto modules to
wrap their ECB code with generic LRW code themselves via lrw_crypt().
Remove the lrw-twofish-avx algorithm which did this. Users who request
lrw(twofish) and previously would have gotten lrw-twofish-avx will now
get lrw(ecb-twofish-avx) instead, which is just as fast.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Convert the 3-way implementation of Twofish from the (deprecated)
blkcipher interface over to the skcipher interface.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The XTS template now wraps an ECB mode algorithm rather than the block
cipher directly. Therefore it is now redundant for crypto modules to
wrap their ECB code with generic XTS code themselves via xts_crypt().
Remove the xts-twofish-3way algorithm which did this. Users who request
xts(twofish) and previously would have gotten xts-twofish-3way will now
get xts(ecb-twofish-3way) instead, which is just as fast.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The LRW template now wraps an ECB mode algorithm rather than the block
cipher directly. Therefore it is now redundant for crypto modules to
wrap their ECB code with generic LRW code themselves via lrw_crypt().
Remove the lrw-twofish-3way algorithm which did this. Users who request
lrw(twofish) and previously would have gotten lrw-twofish-3way will now
get lrw(ecb-twofish-3way) instead, which is just as fast.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Convert the AVX and AVX2 implementations of Serpent from the
(deprecated) ablkcipher and blkcipher interfaces over to the skcipher
interface. Note that this includes replacing the use of ablk_helper
with crypto_simd.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The LRW template now wraps an ECB mode algorithm rather than the block
cipher directly. Therefore it is now redundant for crypto modules to
wrap their ECB code with generic LRW code themselves via lrw_crypt().
Remove the lrw-serpent-avx algorithm which did this. Users who request
lrw(serpent) and previously would have gotten lrw-serpent-avx will now
get lrw(ecb-serpent-avx) instead, which is just as fast.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The LRW template now wraps an ECB mode algorithm rather than the block
cipher directly. Therefore it is now redundant for crypto modules to
wrap their ECB code with generic LRW code themselves via lrw_crypt().
Remove the lrw-serpent-avx2 algorithm which did this. Users who request
lrw(serpent) and previously would have gotten lrw-serpent-avx2 will now
get lrw(ecb-serpent-avx2) instead, which is just as fast.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Convert the SSE2 implementation of Serpent from the (deprecated)
ablkcipher and blkcipher interfaces over to the skcipher interface.
Note that this includes replacing the use of ablk_helper with
crypto_simd.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The XTS template now wraps an ECB mode algorithm rather than the block
cipher directly. Therefore it is now redundant for crypto modules to
wrap their ECB code with generic XTS code themselves via xts_crypt().
Remove the xts-serpent-sse2 algorithm which did this. Users who request
xts(serpent) and previously would have gotten xts-serpent-sse2 will now
get xts(ecb-serpent-sse2) instead, which is just as fast.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The LRW template now wraps an ECB mode algorithm rather than the block
cipher directly. Therefore it is now redundant for crypto modules to
wrap their ECB code with generic LRW code themselves via lrw_crypt().
Remove the lrw-serpent-sse2 algorithm which did this. Users who request
lrw(serpent) and previously would have gotten lrw-serpent-sse2 will now
get lrw(ecb-serpent-sse2) instead, which is just as fast.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add a function to crypto_simd that registers an array of skcipher
algorithms, then allocates and registers the simd wrapper algorithms for
them. It assumes the naming scheme where the names of the underlying
algorithms are prefixed with two underscores.
Also add the corresponding 'unregister' function.
Most of the x86 crypto modules will be able to use these.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The asymmetric key type allows an X.509 certificate to be added even if
its signature's hash algorithm is not available in the crypto API. In
that case 'payload.data[asym_auth]' will be NULL. But the key
restriction code failed to check for this case before trying to use the
signature, resulting in a NULL pointer dereference in
key_or_keyring_common() or in restrict_link_by_signature().
Fix this by returning -ENOPKG when the signature is unsupported.
Reproducer when all the CONFIG_CRYPTO_SHA512* options are disabled and
keyctl has support for the 'restrict_keyring' command:
keyctl new_session
keyctl restrict_keyring @s asymmetric builtin_trusted
openssl req -new -sha512 -x509 -batch -nodes -outform der \
| keyctl padd asymmetric desc @s
Fixes: a511e1af8b ("KEYS: Move the point of trust determination to __key_link()")
Cc: <stable@vger.kernel.org> # v4.7+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
The X.509 parser mishandles the case where the certificate's signature's
hash algorithm is not available in the crypto API. In this case,
x509_get_sig_params() doesn't allocate the cert->sig->digest buffer;
this part seems to be intentional. However,
public_key_verify_signature() is still called via
x509_check_for_self_signed(), which triggers the 'BUG_ON(!sig->digest)'.
Fix this by making public_key_verify_signature() return -ENOPKG if the
hash buffer has not been allocated.
Reproducer when all the CONFIG_CRYPTO_SHA512* options are disabled:
openssl req -new -sha512 -x509 -batch -nodes -outform der \
| keyctl padd asymmetric desc @s
Fixes: 6c2dc5ae4a ("X.509: Extract signature digest and make self-signed cert checks earlier")
Reported-by: Paolo Valente <paolo.valente@linaro.org>
Cc: Paolo Valente <paolo.valente@linaro.org>
Cc: <stable@vger.kernel.org> # v4.7+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
If none of the certificates in a SignerInfo's certificate chain match a
trusted key, nor is the last certificate signed by a trusted key, then
pkcs7_validate_trust_one() tries to check whether the SignerInfo's
signature was made directly by a trusted key. But, it actually fails to
set the 'sig' variable correctly, so it actually verifies the last
signature seen. That will only be the SignerInfo's signature if the
certificate chain is empty; otherwise it will actually be the last
certificate's signature.
This is not by itself a security problem, since verifying any of the
certificates in the chain should be sufficient to verify the SignerInfo.
Still, it's not working as intended so it should be fixed.
Fix it by setting 'sig' correctly for the direct verification case.
Fixes: 757932e6da ("PKCS#7: Handle PKCS#7 messages that contain no X.509 certs")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
If there is a blacklisted certificate in a SignerInfo's certificate
chain, then pkcs7_verify_sig_chain() sets sinfo->blacklisted and returns
0. But, pkcs7_verify() fails to handle this case appropriately, as it
actually continues on to the line 'actual_ret = 0;', indicating that the
SignerInfo has passed verification. Consequently, PKCS#7 signature
verification ignores the certificate blacklist.
Fix this by not considering blacklisted SignerInfos to have passed
verification.
Also fix the function comment with regards to when 0 is returned.
Fixes: 03bb79315d ("PKCS#7: Handle blacklisted certificates")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
When pkcs7_verify_sig_chain() is building the certificate chain for a
SignerInfo using the certificates in the PKCS#7 message, it is passing
the wrong arguments to public_key_verify_signature(). Consequently,
when the next certificate is supposed to be used to verify the previous
certificate, the next certificate is actually used to verify itself.
An attacker can use this bug to create a bogus certificate chain that
has no cryptographic relationship between the beginning and end.
Fortunately I couldn't quite find a way to use this to bypass the
overall signature verification, though it comes very close. Here's the
reasoning: due to the bug, every certificate in the chain beyond the
first actually has to be self-signed (where "self-signed" here refers to
the actual key and signature; an attacker might still manipulate the
certificate fields such that the self_signed flag doesn't actually get
set, and thus the chain doesn't end immediately). But to pass trust
validation (pkcs7_validate_trust()), either the SignerInfo or one of the
certificates has to actually be signed by a trusted key. Since only
self-signed certificates can be added to the chain, the only way for an
attacker to introduce a trusted signature is to include a self-signed
trusted certificate.
But, when pkcs7_validate_trust_one() reaches that certificate, instead
of trying to verify the signature on that certificate, it will actually
look up the corresponding trusted key, which will succeed, and then try
to verify the *previous* certificate, which will fail. Thus, disaster
is narrowly averted (as far as I could tell).
Fixes: 6c2dc5ae4a ("X.509: Extract signature digest and make self-signed cert checks earlier")
Cc: <stable@vger.kernel.org> # v4.7+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Add test vectors for Speck64-XTS, generated in userspace using C code.
The inputs were borrowed from the AES-XTS test vectors, with key lengths
adjusted.
xts-speck64-neon passes these tests. However, they aren't currently
applicable for the generic XTS template, as that only supports a 128-bit
block size.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add test vectors for Speck128-XTS, generated in userspace using C code.
The inputs were borrowed from the AES-XTS test vectors.
Both xts(speck128-generic) and xts-speck128-neon pass these tests.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Export the Speck constants and transform context and the ->setkey(),
->encrypt(), and ->decrypt() functions so that they can be reused by the
ARM NEON implementation of Speck-XTS. The generic key expansion code
will be reused because it is not performance-critical and is not
vectorizable, while the generic encryption and decryption functions are
needed as fallbacks and for the XTS tweak encryption.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add a generic implementation of Speck, including the Speck128 and
Speck64 variants. Speck is a lightweight block cipher that can be much
faster than AES on processors that don't have AES instructions.
We are planning to offer Speck-XTS (probably Speck128/256-XTS) as an
option for dm-crypt and fscrypt on Android, for low-end mobile devices
with older CPUs such as ARMv7 which don't have the Cryptography
Extensions. Currently, such devices are unencrypted because AES is not
fast enough, even when the NEON bit-sliced implementation of AES is
used. Other AES alternatives such as Twofish, Threefish, Camellia,
CAST6, and Serpent aren't fast enough either; it seems that only a
modern ARX cipher can provide sufficient performance on these devices.
This is a replacement for our original proposal
(https://patchwork.kernel.org/patch/10101451/) which was to offer
ChaCha20 for these devices. However, the use of a stream cipher for
disk/file encryption with no space to store nonces would have been much
more insecure than we thought initially, given that it would be used on
top of flash storage as well as potentially on top of F2FS, neither of
which is guaranteed to overwrite data in-place.
Speck has been somewhat controversial due to its origin. Nevertheless,
it has a straightforward design (it's an ARX cipher), and it appears to
be the leading software-optimized lightweight block cipher currently,
with the most cryptanalysis. It's also easy to implement without side
channels, unlike AES. Moreover, we only intend Speck to be used when
the status quo is no encryption, due to AES not being fast enough.
We've also considered a novel length-preserving encryption mode based on
ChaCha20 and Poly1305. While theoretically attractive, such a mode
would be a brand new crypto construction and would be more complicated
and difficult to implement efficiently in comparison to Speck-XTS.
There is confusion about the byte and word orders of Speck, since the
original paper doesn't specify them. But we have implemented it using
the orders the authors recommended in a correspondence with them. The
test vectors are taken from the original paper but were mapped to byte
arrays using the recommended byte and word orders.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The RSA private key for the first form should have
version, prime1, prime2, exponent1, exponent2, coefficient
values 0.
With non-zero values for prime1,2, exponent 1,2 and coefficient
the Intel QAT driver will assume that values are provided for the
private key second form. This will result in signature verification
failures for modules where QAT device is present and the modules
are signed with rsa,sha256.
Cc: <stable@vger.kernel.org>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Conor McLoughlin <conor.mcloughlin@intel.com>
Reviewed-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This module registers crc32 and crc32c algorithms that use the
optional CRC32[bhwd] and CRC32C[bhwd] instructions in MIPSr6 cores.
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@mips.com>
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-mips@linux-mips.org
Cc: linux-crypto@vger.kernel.org
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Patchwork: https://patchwork.linux-mips.org/patch/18601/
[jhogan@kernel.org: Add CRYPTO_ALG_OPTIONAL_KEY flag on Eric Biggers'
suggestion, due to commit a208fa8f33 ("crypto: hash - annotate
algorithms taking optional key") in v4.16-rc1]
The crypto engine could actually only enqueue hash and ablkcipher request.
This patch permit it to enqueue any type of crypto_async_request.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Tested-by: Fabien Dessenne <fabien.dessenne@st.com>
Tested-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
After checking all possible call chains to crypto_report here,
my tool finds that crypto_report is never called in atomic context.
And crypto_report calls crypto_alg_match which calls down_read,
thus it proves again that crypto_report can call functions which may sleep.
Thus GFP_ATOMIC is not necessary, and it can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
After checking all possible call chains to kzalloc here,
my tool finds that this kzalloc is never called in atomic context.
Thus GFP_ATOMIC is not necessary, and it can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There is no need for ahash_mcryptd_{update,final,finup,digest}(); we
should just call crypto_ahash_*() directly.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Export and import are mandatory in async hash. As drivers were
rewritten, drop empty wrappers and correct init of ahash transformation.
Signed-off-by: Kamil Konieczny <k.konieczny@partner.samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull crypto fixes from Herbert Xu:
"This fixes the following issues:
- oversize stack frames on mn10300 in sha3-generic
- warning on old compilers in sha3-generic
- API error in sun4i_ss_prng
- potential dead-lock in sun4i_ss_prng
- null-pointer dereference in sha512-mb
- endless loop when DECO acquire fails in caam
- kernel oops when hashing empty message in talitos"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: sun4i_ss_prng - convert lock to _bh in sun4i_ss_prng_generate
crypto: sun4i_ss_prng - fix return value of sun4i_ss_prng_generate
crypto: caam - fix endless loop when DECO acquire fails
crypto: sha3-generic - Use __optimize to support old compilers
compiler-gcc.h: __nostackprotector needs gcc-4.4 and up
compiler-gcc.h: Introduce __optimize function attribute
crypto: sha3-generic - deal with oversize stack frames
crypto: talitos - fix Kernel Oops on hashing an empty file
crypto: sha512-mb - initialize pending lengths correctly
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As reported by kbuild test robot, the optimized SHA3 C implementation
compiles to mn10300 code that uses a disproportionate amount of stack
space, i.e.,
crypto/sha3_generic.c: In function 'keccakf':
crypto/sha3_generic.c:147:1: warning: the frame size of 1232 bytes is larger than 1024 bytes [-Wframe-larger-than=]
As kindly diagnosed by Arnd, this does not only occur when building for
the mn10300 architecture (which is what the report was about) but also
for h8300, and builds for other 32-bit architectures show an increase in
stack space utilization as well.
Given that SHA3 operates on 64-bit quantities, and keeps a state matrix
of 25 64-bit words, it is not surprising that 32-bit architectures with
few general purpose registers are impacted the most by this, and it is
therefore reasonable to implement a workaround that distinguishes between
32-bit and 64-bit architectures.
Arnd figured out that taking the round calculation out of the loop, and
inlining it explicitly but only on 64-bit architectures preserves most
of the performance gain achieved by the rewrite, and also gets rid of
the excessive use of stack space.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull crypto updates from Herbert Xu:
"API:
- Enforce the setting of keys for keyed aead/hash/skcipher
algorithms.
- Add multibuf speed tests in tcrypt.
Algorithms:
- Improve performance of sha3-generic.
- Add native sha512 support on arm64.
- Add v8.2 Crypto Extentions version of sha3/sm3 on arm64.
- Avoid hmac nesting by requiring underlying algorithm to be unkeyed.
- Add cryptd_max_cpu_qlen module parameter to cryptd.
Drivers:
- Add support for EIP97 engine in inside-secure.
- Add inline IPsec support to chelsio.
- Add RevB core support to crypto4xx.
- Fix AEAD ICV check in crypto4xx.
- Add stm32 crypto driver.
- Add support for BCM63xx platforms in bcm2835 and remove bcm63xx.
- Add Derived Key Protocol (DKP) support in caam.
- Add Samsung Exynos True RNG driver.
- Add support for Exynos5250+ SoCs in exynos PRNG driver"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (166 commits)
crypto: picoxcell - Fix error handling in spacc_probe()
crypto: arm64/sha512 - fix/improve new v8.2 Crypto Extensions code
crypto: arm64/sm3 - new v8.2 Crypto Extensions implementation
crypto: arm64/sha3 - new v8.2 Crypto Extensions implementation
crypto: testmgr - add new testcases for sha3
crypto: sha3-generic - export init/update/final routines
crypto: sha3-generic - simplify code
crypto: sha3-generic - rewrite KECCAK transform to help the compiler optimize
crypto: sha3-generic - fixes for alignment and big endian operation
crypto: aesni - handle zero length dst buffer
crypto: artpec6 - remove select on non-existing CRYPTO_SHA384
hwrng: bcm2835 - Remove redundant dev_err call in bcm2835_rng_probe()
crypto: stm32 - remove redundant dev_err call in stm32_cryp_probe()
crypto: axis - remove unnecessary platform_get_resource() error check
crypto: testmgr - test misuse of result in ahash
crypto: inside-secure - make function safexcel_try_push_requests static
crypto: aes-generic - fix aes-generic regression on powerpc
crypto: chelsio - Fix indentation warning
crypto: arm64/sha1-ce - get rid of literal pool
crypto: arm64/sha2-ce - move the round constant table to .rodata section
...
Pull poll annotations from Al Viro:
"This introduces a __bitwise type for POLL### bitmap, and propagates
the annotations through the tree. Most of that stuff is as simple as
'make ->poll() instances return __poll_t and do the same to local
variables used to hold the future return value'.
Some of the obvious brainos found in process are fixed (e.g. POLLIN
misspelled as POLL_IN). At that point the amount of sparse warnings is
low and most of them are for genuine bugs - e.g. ->poll() instance
deciding to return -EINVAL instead of a bitmap. I hadn't touched those
in this series - it's large enough as it is.
Another problem it has caught was eventpoll() ABI mess; select.c and
eventpoll.c assumed that corresponding POLL### and EPOLL### were
equal. That's true for some, but not all of them - EPOLL### are
arch-independent, but POLL### are not.
The last commit in this series separates userland POLL### values from
the (now arch-independent) kernel-side ones, converting between them
in the few places where they are copied to/from userland. AFAICS, this
is the least disruptive fix preserving poll(2) ABI and making epoll()
work on all architectures.
As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
it will trigger only on what would've triggered EPOLLWRBAND on other
architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
at all on sparc. With this patch they should work consistently on all
architectures"
* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
make kernel-side POLL... arch-independent
eventpoll: no need to mask the result of epi_item_poll() again
eventpoll: constify struct epoll_event pointers
debugging printk in sg_poll() uses %x to print POLL... bitmap
annotate poll(2) guts
9p: untangle ->poll() mess
->si_band gets POLL... bitmap stored into a user-visible long field
ring_buffer_poll_wait() return value used as return value of ->poll()
the rest of drivers/*: annotate ->poll() instances
media: annotate ->poll() instances
fs: annotate ->poll() instances
ipc, kernel, mm: annotate ->poll() instances
net: annotate ->poll() instances
apparmor: annotate ->poll() instances
tomoyo: annotate ->poll() instances
sound: annotate ->poll() instances
acpi: annotate ->poll() instances
crypto: annotate ->poll() instances
block: annotate ->poll() instances
x86: annotate ->poll() instances
...
Pull block updates from Jens Axboe:
"This is the main pull request for block IO related changes for the
4.16 kernel. Nothing major in this pull request, but a good amount of
improvements and fixes all over the map. This contains:
- BFQ improvements, fixes, and cleanups from Angelo, Chiara, and
Paolo.
- Support for SMR zones for deadline and mq-deadline from Damien and
Christoph.
- Set of fixes for bcache by way of Michael Lyle, including fixes
from himself, Kent, Rui, Tang, and Coly.
- Series from Matias for lightnvm with fixes from Hans Holmberg,
Javier, and Matias. Mostly centered around pblk, and the removing
rrpc 1.2 in preparation for supporting 2.0.
- A couple of NVMe pull requests from Christoph. Nothing major in
here, just fixes and cleanups, and support for command tracing from
Johannes.
- Support for blk-throttle for tracking reads and writes separately.
From Joseph Qi. A few cleanups/fixes also for blk-throttle from
Weiping.
- Series from Mike Snitzer that enables dm to register its queue more
logically, something that's alwways been problematic on dm since
it's a stacked device.
- Series from Ming cleaning up some of the bio accessor use, in
preparation for supporting multipage bvecs.
- Various fixes from Ming closing up holes around queue mapping and
quiescing.
- BSD partition fix from Richard Narron, fixing a problem where we
can't mount newer (10/11) FreeBSD partitions.
- Series from Tejun reworking blk-mq timeout handling. The previous
scheme relied on atomic bits, but it had races where we would think
a request had timed out if it to reused at the wrong time.
- null_blk now supports faking timeouts, to enable us to better
exercise and test that functionality separately. From me.
- Kill the separate atomic poll bit in the request struct. After
this, we don't use the atomic bits on blk-mq anymore at all. From
me.
- sgl_alloc/free helpers from Bart.
- Heavily contended tag case scalability improvement from me.
- Various little fixes and cleanups from Arnd, Bart, Corentin,
Douglas, Eryu, Goldwyn, and myself"
* 'for-4.16/block' of git://git.kernel.dk/linux-block: (186 commits)
block: remove smart1,2.h
nvme: add tracepoint for nvme_complete_rq
nvme: add tracepoint for nvme_setup_cmd
nvme-pci: introduce RECONNECTING state to mark initializing procedure
nvme-rdma: remove redundant boolean for inline_data
nvme: don't free uuid pointer before printing it
nvme-pci: Suspend queues after deleting them
bsg: use pr_debug instead of hand crafted macros
blk-mq-debugfs: don't allow write on attributes with seq_operations set
nvme-pci: Fix queue double allocations
block: Set BIO_TRACE_COMPLETION on new bio during split
blk-throttle: use queue_is_rq_based
block: Remove kblockd_schedule_delayed_work{,_on}()
blk-mq: Avoid that blk_mq_delay_run_hw_queue() introduces unintended delays
blk-mq: Rename blk_mq_request_direct_issue() into blk_mq_request_issue_directly()
lib/scatterlist: Fix chaining support in sgl_alloc_order()
blk-throttle: track read and write request individually
block: add bdev_read_only() checks to common helpers
block: fail op_is_write() requests to read-only partitions
blk-throttle: export io_serviced_recursive, io_service_bytes_recursive
...
All current SHA3 test cases are smaller than the SHA3 block size, which
means not all code paths are being exercised. So add a new test case to
each variant, and make one of the existing test cases chunked.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
To allow accelerated implementations to fall back to the generic
routines, e.g., in contexts where a SIMD based implementation is
not allowed to run, expose the generic SHA3 init/update/final
routines to other modules.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In preparation of exposing the generic SHA3 implementation to other
versions as a fallback, simplify the code, and remove an inconsistency
in the output handling (endian swabbing rsizw words of state before
writing the output does not make sense)
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The way the KECCAK transform is currently coded involves many references
into the state array using indexes that are calculated at runtime using
simple but non-trivial arithmetic. This forces the compiler to treat the
state matrix as an array in memory rather than keep it in registers,
which results in poor performance.
So instead, let's rephrase the algorithm using fixed array indexes only.
This helps the compiler keep the state matrix in registers, resulting
in the following speedup (SHA3-256 performance in cycles per byte):
before after speedup
Intel Core i7 @ 2.0 GHz (2.9 turbo) 100.6 35.7 2.8x
Cortex-A57 @ 2.0 GHz (64-bit mode) 101.6 12.7 8.0x
Cortex-A53 @ 1.0 GHz 224.4 15.8 14.2x
Cortex-A57 @ 2.0 GHz (32-bit mode) 201.8 63.0 3.2x
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Ensure that the input is byte swabbed before injecting it into the
SHA3 transform. Use the get_unaligned() accessor for this so that
we don't perform unaligned access inadvertently on architectures
that do not support that.
Cc: <stable@vger.kernel.org>
Fixes: 53964b9ee6 ("crypto: sha3 - Add SHA-3 hash algorithm")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Async hash operations can use result pointer in final/finup/digest,
but not in init/update/export/import, so test it for misuse.
Signed-off-by: Kamil Konieczny <k.konieczny@partner.samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
My last bugfix added -Os on the command line, which unfortunately caused
a build regression on powerpc in some configurations.
I've done some more analysis of the original problem and found slightly
different workaround that avoids this regression and also results in
better performance on gcc-7.0: -fcode-hoisting is an optimization step
that got added in gcc-7 and that for all gcc-7 versions causes worse
performance.
This disables -fcode-hoisting on all compilers that understand the option.
For gcc-7.1 and 7.2 I found the same performance as my previous patch
(using -Os), in gcc-7.0 it was even better. On gcc-8 I could see no
change in performance from this patch. In theory, code hoisting should
not be able make things better for the AES cipher, so leaving it
disabled for gcc-8 only serves to simplify the Makefile change.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Link: https://www.mail-archive.com/linux-crypto@vger.kernel.org/msg30418.html
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=83356
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=83651
Fixes: 148b974dee ("crypto: aes-generic - build with -Os on gcc-7+")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull crypto fix from Herbert Xu:
"This fixes a NULL pointer dereference in crypto_remove_spawns that can
be triggered through af_alg"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: algapi - fix NULL dereference in crypto_remove_spawns()
Convert salsa20-asm from the deprecated "blkcipher" API to the
"skcipher" API, in the process fixing it up to use the generic helpers.
This allows removing the salsa20_keysetup() and salsa20_ivsetup()
assembly functions, which aren't performance critical; the C versions do
just fine.
This also fixes the same bug that salsa20-generic had, where the state
array was being maintained directly in the transform context rather than
on the stack or in the request context. Thus, if multiple threads used
the same Salsa20 transform concurrently they produced the wrong results.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Export the Salsa20 constants, transform context, and initialization
functions so that they can be reused by the x86 implementation.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Convert salsa20-generic from the deprecated "blkcipher" API to the
"skcipher" API, in the process fixing it up to be thread-safe (as the
crypto API expects) by maintaining each request's state separately from
the transform context.
Also remove the unnecessary cra_alignmask and tighten validation of the
key size by accepting only 16 or 32 bytes, not anything in between.
These changes bring the code close to the way chacha20-generic does
things, so hopefully it will be easier to maintain in the future.
However, the way Salsa20 interprets the IV is still slightly different;
that was not changed.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
While testing other changes, I discovered that gcc-7.2.1 produces badly
optimized code for aes_encrypt/aes_decrypt. This is especially true when
CONFIG_UBSAN_SANITIZE_ALL is enabled, where it leads to extremely
large stack usage that in turn might cause kernel stack overflows:
crypto/aes_generic.c: In function 'aes_encrypt':
crypto/aes_generic.c:1371:1: warning: the frame size of 4880 bytes is larger than 2048 bytes [-Wframe-larger-than=]
crypto/aes_generic.c: In function 'aes_decrypt':
crypto/aes_generic.c:1441:1: warning: the frame size of 4864 bytes is larger than 2048 bytes [-Wframe-larger-than=]
I verified that this problem exists on all architectures that are
supported by gcc-7.2, though arm64 in particular is less affected than
the others. I also found that gcc-7.1 and gcc-8 do not show the extreme
stack usage but still produce worse code than earlier versions for this
file, apparently because of optimization passes that generally provide
a substantial improvement in object code quality but understandably fail
to find any shortcuts in the AES algorithm.
Possible workarounds include
a) disabling -ftree-pre and -ftree-sra optimizations, this was an earlier
patch I tried, which reliably fixed the stack usage, but caused a
serious performance regression in some versions, as later testing
found.
b) disabling UBSAN on this file or all ciphers, as suggested by Ard
Biesheuvel. This would lead to massively better crypto performance in
UBSAN-enabled kernels and avoid the stack usage, but there is a concern
over whether we should exclude arbitrary files from UBSAN at all.
c) Forcing the optimization level in a different way. Similar to a),
but rather than deselecting specific optimization stages,
this now uses "gcc -Os" for this file, regardless of the
CONFIG_CC_OPTIMIZE_FOR_PERFORMANCE/SIZE option. This is a reliable
workaround for the stack consumption on all architecture, and I've
retested the performance results now on x86, cycles/byte (lower is
better) for cbc(aes-generic) with 256 bit keys:
-O2 -Os
gcc-6.3.1 14.9 15.1
gcc-7.0.1 14.7 15.3
gcc-7.1.1 15.3 14.7
gcc-7.2.1 16.8 15.9
gcc-8.0.0 15.5 15.6
This implements the option c) by enabling forcing -Os on all compiler
versions starting with gcc-7.1. As a workaround for PR83356, it would
only be needed for gcc-7.2+ with UBSAN enabled, but since it also shows
better performance on gcc-7.1 without UBSAN, it seems appropriate to
use the faster version here as well.
Side note: during testing, I also played with the AES code in libressl,
which had a similar performance regression from gcc-6 to gcc-7.2,
but was three times slower overall. It might be interesting to
investigate that further and possibly port the Linux implementation
into that.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=83356
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=83651
Cc: Richard Biener <rguenther@suse.de>
Cc: Jakub Jelinek <jakub@gcc.gnu.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Similar to what was done for the hash API, update the AEAD API to track
whether each transform has been keyed, and reject encryption/decryption
if a key is needed but one hasn't been set.
This isn't quite as important as the equivalent fix for the hash API
because AEADs always require a key, so are unlikely to be used without
one. Still, tracking the key will prevent accidental unkeyed use.
algif_aead also had to track the key anyway, so the new flag replaces
that and slightly simplifies the algif_aead implementation.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Similar to what was done for the hash API, update the skcipher API to
track whether each transform has been keyed, and reject
encryption/decryption if a key is needed but one hasn't been set.
This isn't as important as the equivalent fix for the hash API because
symmetric ciphers almost always require a key (the "null cipher" is the
only exception), so are unlikely to be used without one. Still,
tracking the key will prevent accidental unkeyed use. algif_skcipher
also had to track the key anyway, so the new flag replaces that and
simplifies the algif_skcipher implementation.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Now that the crypto API prevents a keyed hash from being used without
setting the key, there's no need for GHASH to do this check itself.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently, almost none of the keyed hash algorithms check whether a key
has been set before proceeding. Some algorithms are okay with this and
will effectively just use a key of all 0's or some other bogus default.
However, others will severely break, as demonstrated using
"hmac(sha3-512-generic)", the unkeyed use of which causes a kernel crash
via a (potentially exploitable) stack buffer overflow.
A while ago, this problem was solved for AF_ALG by pairing each hash
transform with a 'has_key' bool. However, there are still other places
in the kernel where userspace can specify an arbitrary hash algorithm by
name, and the kernel uses it as unkeyed hash without checking whether it
is really unkeyed. Examples of this include:
- KEYCTL_DH_COMPUTE, via the KDF extension
- dm-verity
- dm-crypt, via the ESSIV support
- dm-integrity, via the "internal hash" mode with no key given
- drbd (Distributed Replicated Block Device)
This bug is especially bad for KEYCTL_DH_COMPUTE as that requires no
privileges to call.
Fix the bug for all users by adding a flag CRYPTO_TFM_NEED_KEY to the
->crt_flags of each hash transform that indicates whether the transform
still needs to be keyed or not. Then, make the hash init, import, and
digest functions return -ENOKEY if the key is still needed.
The new flag also replaces the 'has_key' bool which algif_hash was
previously using, thereby simplifying the algif_hash implementation.
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
We need to consistently enforce that keyed hashes cannot be used without
setting the key. To do this we need a reliable way to determine whether
a given hash algorithm is keyed or not. AF_ALG currently does this by
checking for the presence of a ->setkey() method. However, this is
actually slightly broken because the CRC-32 algorithms implement
->setkey() but can also be used without a key. (The CRC-32 "key" is not
actually a cryptographic key but rather represents the initial state.
If not overridden, then a default initial state is used.)
Prepare to fix this by introducing a flag CRYPTO_ALG_OPTIONAL_KEY which
indicates that the algorithm has a ->setkey() method, but it is not
required to be called. Then set it on all the CRC-32 algorithms.
The same also applies to the Adler-32 implementation in Lustre.
Also, the cryptd and mcryptd templates have to pass through the flag
from their underlying algorithm.
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Since Poly1305 requires a nonce per invocation, the Linux kernel
implementations of Poly1305 don't use the crypto API's keying mechanism
and instead expect the key and nonce as the first 32 bytes of the data.
But ->setkey() is still defined as a stub returning an error code. This
prevents Poly1305 from being used through AF_ALG and will also break it
completely once we start enforcing that all crypto API users (not just
AF_ALG) call ->setkey() if present.
Fix it by removing crypto_poly1305_setkey(), leaving ->setkey as NULL.
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When the mcryptd template is used to wrap an unkeyed hash algorithm,
don't install a ->setkey() method to the mcryptd instance. This change
is necessary for mcryptd to keep working with unkeyed hash algorithms
once we start enforcing that ->setkey() is called when present.
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When the cryptd template is used to wrap an unkeyed hash algorithm,
don't install a ->setkey() method to the cryptd instance. This change
is necessary for cryptd to keep working with unkeyed hash algorithms
once we start enforcing that ->setkey() is called when present.
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Templates that use an shash spawn can use crypto_shash_alg_has_setkey()
to determine whether the underlying algorithm requires a key or not.
But there was no corresponding function for ahash spawns. Add it.
Note that the new function actually has to support both shash and ahash
algorithms, since the ahash API can be used with either.
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There seems to be a cut-n-paste bug with the name of the buffer being
free'd, xoutbuf should be used instead of axbuf.
Detected by CoverityScan, CID#1463420 ("Copy-paste error")
Fixes: 427988d981 ("crypto: tcrypt - add multibuf aead speed test")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Trivial fix to spelling mistakes in pr_err error message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The user space interface allows specifying the type and mask field used
to allocate the cipher. Only a subset of the possible flags are intended
for user space. Therefore, white-list the allowed flags.
In case the user space caller uses at least one non-allowed flag, EINVAL
is returned.
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When char is signed, storing the values 0xba (186) and 0xad (173) in the
`guard` array produces signed overflow. Change the type of `guard` to
static unsigned char to correct undefined behavior and reduce function
stack usage.
Signed-off-by: Joey Pabalinas <joeypabalinas@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use the sgl_alloc() and sgl_free() functions instead of open coding
these functions.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull crypto fixes from Herbert Xu:
"This fixes the following issues:
- racy use of ctx->rcvused in af_alg
- algif_aead crash in chacha20poly1305
- freeing bogus pointer in pcrypt
- build error on MIPS in mpi
- memory leak in inside-secure
- memory overwrite in inside-secure
- NULL pointer dereference in inside-secure
- state corruption in inside-secure
- build error without CRYPTO_GF128MUL in chelsio
- use after free in n2"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: inside-secure - do not use areq->result for partial results
crypto: inside-secure - fix request allocations in invalidation path
crypto: inside-secure - free requests even if their handling failed
crypto: inside-secure - per request invalidation
lib/mpi: Fix umul_ppmm() for MIPS64r6
crypto: pcrypt - fix freeing pcrypt instances
crypto: n2 - cure use after free
crypto: af_alg - Fix race around ctx->rcvused by making it atomic_t
crypto: chacha20poly1305 - validate the digest size
crypto: chelsio - select CRYPTO_GF128MUL
Now that nothing in poly1305-generic assumes any special alignment,
remove the cra_alignmask so that the crypto API does not have to
unnecessarily align the buffers.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently the only part of poly1305-generic which is assuming special
alignment is the part where the final digest is written. Switch this
over to the unaligned access macros so that we'll be able to remove the
cra_alignmask.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There is a message posted to the crypto notifier chain when an algorithm
is unregistered, and when a template is registered or unregistered. But
nothing is listening for those messages; currently there are only
listeners for the algorithm request and registration messages.
Get rid of these unused notifications for now.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reference counters should use refcount_t rather than atomic_t, since the
refcount_t implementation can prevent overflows, reducing the
exploitability of reference leak bugs. crypto_alg.cra_refcount is a
reference counter with the usual semantics, so switch it over to
refcount_t.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
syzkaller triggered a NULL pointer dereference in crypto_remove_spawns()
via a program that repeatedly and concurrently requests AEADs
"authenc(cmac(des3_ede-asm),pcbc-aes-aesni)" and hashes "cmac(des3_ede)"
through AF_ALG, where the hashes are requested as "untested"
(CRYPTO_ALG_TESTED is set in ->salg_mask but clear in ->salg_feat; this
causes the template to be instantiated for every request).
Although AF_ALG users really shouldn't be able to request an "untested"
algorithm, the NULL pointer dereference is actually caused by a
longstanding race condition where crypto_remove_spawns() can encounter
an instance which has had spawn(s) "grabbed" but hasn't yet been
registered, resulting in ->cra_users still being NULL.
We probably should properly initialize ->cra_users earlier, but that
would require updating many templates individually. For now just fix
the bug in a simple way that can easily be backported: make
crypto_remove_spawns() treat a NULL ->cra_users list as empty.
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The performance of some aead tfm providers is affected by
the amount of parallelism possible with the processing.
Introduce an async aead concurrent multiple buffer
processing speed test to be able to test performance of such
tfm providers.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The performance of some skcipher tfm providers is affected by
the amount of parallelism possible with the processing.
Introduce an async skcipher concurrent multiple buffer
processing speed test to be able to test performance of such
tfm providers.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The multi buffer concurrent requests ahash speed test only
supported the cycles mode. Add support for the so called
jiffies mode that test performance of bytes/sec.
We only add support for digest mode at the moment.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For multiple buffers speed tests, the number of buffers, or
requests, used actually sets the level of parallelism a tfm
provider may utilize to hide latency. The existing number
(of 8) is good for some software based providers but not
enough for many HW providers with deep FIFOs.
Add a module parameter that allows setting the number of
multiple buffers/requests used, leaving the default at 8.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The AEAD speed test pretended to support decryption, however that support
was broken as decryption requires a valid auth field which the test did
not provide.
Fix this by running the encryption path once with inout/output sgls
switched to calculate the auth field prior to performing decryption
speed tests.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The multi buffer ahash speed test was allocating multiple
buffers for use with the multiple outstanding requests
it was starting but never actually using them (except
to free them), instead using a different single statically
allocated buffer for all requests.
Fix this by actually using the allocated buffers for the test.
It is noted that it may seem tempting to instead remove the
allocation and free of the multiple buffers and leave things as
they are since this is a hash test where the input is read
only. However, after consideration I believe that multiple
buffers better reflect real life scenario with regard
to data cache and TLB behaviours etc.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull crypto fixes from Herbert Xu:
"This fixes the following issues:
- fix chacha20 crash on zero-length input due to unset IV
- fix potential race conditions in mcryptd with spinlock
- only wait once at top of algif recvmsg to avoid inconsistencies
- fix potential use-after-free in algif_aead/algif_skcipher"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: af_alg - fix race accessing cipher request
crypto: mcryptd - protect the per-CPU queue with a lock
crypto: af_alg - wait for data at beginning of recvmsg
crypto: skcipher - set walk.iv for zero-length inputs
This patch remove two unused variable and some dead "code" using it.
Fixes: 92932d03c2 ("crypto: seqiv - Remove AEAD compatibility code")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch remove two unused variable and some dead "code" using it.
Fixes: 66008d4230 ("crypto: echainiv - Remove AEAD compatibility code")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The comment in gf128mul_x8_ble() was copy-and-pasted from gf128mul.h and
makes no sense in the new context. Remove it.
Cc: Harsh Jain <harsh@chelsio.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Since commit 499a66e6b6 ("crypto: null - Remove default null
blkcipher"), crypto_get_default_null_skcipher2() and
crypto_put_default_null_skcipher2() are the same as their non-2
equivalents. So switch callers of the "2" versions over to the original
versions and remove the "2" versions.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
crypto_larval_lookup() is not used outside of crypto/api.c, so unexport
it and mark it 'static'.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
pcrypt is using the old way of freeing instances, where the ->free()
method specified in the 'struct crypto_template' is passed a pointer to
the 'struct crypto_instance'. But the crypto_instance is being
kfree()'d directly, which is incorrect because the memory was actually
allocated as an aead_instance, which contains the crypto_instance at a
nonzero offset. Thus, the wrong pointer was being kfree()'d.
Fix it by switching to the new way to free aead_instance's where the
->free() method is specified in the aead_instance itself.
Reported-by: syzbot <syzkaller@googlegroups.com>
Fixes: 0496f56065 ("crypto: pcrypt - Add support for new AEAD interface")
Cc: <stable@vger.kernel.org> # v4.2+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This variable was increased and decreased without any protection.
Result was an occasional misscount and negative wrap around resulting
in false resource allocation failures.
Fixes: 7d2c3f54e6 ("crypto: af_alg - remove locking in async callback")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If the rfc7539 template was instantiated with a hash algorithm with
digest size larger than 16 bytes (POLY1305_DIGEST_SIZE), then the digest
overran the 'tag' buffer in 'struct chachapoly_req_ctx', corrupting the
subsequent memory, including 'cryptlen'. This caused a crash during
crypto_skcipher_decrypt().
Fix it by, when instantiating the template, requiring that the
underlying hash algorithm has the digest size expected for Poly1305.
Reproducer:
#include <linux/if_alg.h>
#include <sys/socket.h>
#include <unistd.h>
int main()
{
int algfd, reqfd;
struct sockaddr_alg addr = {
.salg_type = "aead",
.salg_name = "rfc7539(chacha20,sha256)",
};
unsigned char buf[32] = { 0 };
algfd = socket(AF_ALG, SOCK_SEQPACKET, 0);
bind(algfd, (void *)&addr, sizeof(addr));
setsockopt(algfd, SOL_ALG, ALG_SET_KEY, buf, sizeof(buf));
reqfd = accept(algfd, 0, 0);
write(reqfd, buf, 16);
read(reqfd, buf, 16);
}
Reported-by: syzbot <syzkaller@googlegroups.com>
Fixes: 71ebc4d1b2 ("crypto: chacha20poly1305 - Add a ChaCha20-Poly1305 AEAD construction, RFC7539")
Cc: <stable@vger.kernel.org> # v4.2+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull crypto fixes from Herbert Xu:
"This push fixes the following issues:
- buffer overread in RSA
- potential use after free in algif_aead.
- error path null pointer dereference in af_alg
- forbid combinations such as hmac(hmac(sha3)) which may crash
- crash in salsa20 due to incorrect API usage"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: salsa20 - fix blkcipher_walk API usage
crypto: hmac - require that the underlying hash algorithm is unkeyed
crypto: af_alg - fix NULL pointer dereference in
crypto: algif_aead - fix reference counting of null skcipher
crypto: rsa - fix buffer overread when stripping leading zeroes
The cryptd_max_cpu_qlen module parameter is local to the source and does
not need to be in global scope, so make it static.
Cleans up sparse warning:
crypto/cryptd.c:35:14: warning: symbol 'cryptd_max_cpu_qlen' was not
declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When invoking an asynchronous cipher operation, the invocation of the
callback may be performed before the subsequent operations in the
initial code path are invoked. The callback deletes the cipher request
data structure which implies that after the invocation of the
asynchronous cipher operation, this data structure must not be accessed
any more.
The setting of the return code size with the request data structure must
therefore be moved before the invocation of the asynchronous cipher
operation.
Fixes: e870456d8e ("crypto: algif_skcipher - overhaul memory management")
Fixes: d887c52d6a ("crypto: algif_aead - overhaul memory management")
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
mcryptd_enqueue_request() grabs the per-CPU queue struct and protects
access to it with disabled preemption. Then it schedules a worker on the
same CPU. The worker in mcryptd_queue_worker() guards access to the same
per-CPU variable with disabled preemption.
If we take CPU-hotplug into account then it is possible that between
queue_work_on() and the actual invocation of the worker the CPU goes
down and the worker will be scheduled on _another_ CPU. And here the
preempt_disable() protection does not work anymore. The easiest thing is
to add a spin_lock() to guard access to the list.
Another detail: mcryptd_queue_worker() is not processing more than
MCRYPTD_BATCH invocation in a row. If there are still items left, then
it will invoke queue_work() to proceed with more later. *I* would
suggest to simply drop that check because it does not use a system
workqueue and the workqueue is already marked as "CPU_INTENSIVE". And if
preemption is required then the scheduler should do it.
However if queue_work() is used then the work item is marked as CPU
unbound. That means it will try to run on the local CPU but it may run
on another CPU as well. Especially with CONFIG_DEBUG_WQ_FORCE_RR_CPU=y.
Again, the preempt_disable() won't work here but lock which was
introduced will help.
In order to keep work-item on the local CPU (and avoid RR) I changed it
to queue_work_on().
Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The wait for data is a non-atomic operation that can sleep and therefore
potentially release the socket lock. The release of the socket lock
allows another thread to modify the context data structure. The waiting
operation for new data therefore must be called at the beginning of
recvmsg. This prevents a race condition where checks of the members of
the context data structure are performed by recvmsg while there is a
potential for modification of these values.
Fixes: e870456d8e ("crypto: algif_skcipher - overhaul memory management")
Fixes: d887c52d6a ("crypto: algif_aead - overhaul memory management")
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
All the ChaCha20 algorithms as well as the ARM bit-sliced AES-XTS
algorithms call skcipher_walk_virt(), then access the IV (walk.iv)
before checking whether any bytes need to be processed (walk.nbytes).
But if the input is empty, then skcipher_walk_virt() doesn't set the IV,
and the algorithms crash trying to use the uninitialized IV pointer.
Fix it by setting the IV earlier in skcipher_walk_virt(). Also fix it
for the AEAD walk functions.
This isn't a perfect solution because we can't actually align the IV to
->cra_alignmask unless there are bytes to process, for one because the
temporary buffer for the aligned IV is freed by skcipher_walk_done(),
which is only called when there are bytes to process. Thus, algorithms
that require aligned IVs will still need to avoid accessing the IV when
walk.nbytes == 0. Still, many algorithms/architectures are fine with
IVs having any alignment, and even for those that aren't, a misaligned
pointer bug is much less severe than an uninitialized pointer bug.
This change also matches the behavior of the older blkcipher_walk API.
Fixes: 0cabf2af6f ("crypto: skcipher - Fix crash on zero-length input")
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
->pkey_algo used to be an enum, but was changed to a string by commit
4e8ae72a75 ("X.509: Make algo identifiers text instead of enum"). But
two comparisons were not updated. Fix them to use strcmp().
This bug broke signature verification in certain configurations,
depending on whether the string constants were deduplicated or not.
Fixes: 4e8ae72a75 ("X.509: Make algo identifiers text instead of enum")
Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Use crypto_shash_digest() instead of crypto_shash_init() followed by
crypto_shash_finup(). (For simplicity only; they are equivalent.)
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
In public_key_verify_signature(), if akcipher_request_alloc() fails, we
return -ENOMEM. But that error code was set 25 lines above, and by
accident someone could easily insert new code in between that assigns to
'ret', which would introduce a signature verification bypass. Make the
code clearer by moving the -ENOMEM down to where it is used.
Additionally, the callers of public_key_verify_signature() only consider
a negative return value to be an error. This means that if any positive
return value is accidentally introduced deeper in the call stack (e.g.
'return EBADMSG' instead of 'return -EBADMSG' somewhere in RSA),
signature verification will be bypassed. Make things more robust by
having public_key_verify_signature() warn about positive errors and
translate them into -EINVAL.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Use crypto_shash_digest() instead of crypto_shash_init() followed by
crypto_shash_finup(). (For simplicity only; they are equivalent.)
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
pkcs7_validate_trust_one() used 'x509->next == x509' to identify a
self-signed certificate. That's wrong; ->next is simply the link in the
linked list of certificates in the PKCS#7 message. It should be
checking ->signer instead. Fix it.
Fortunately this didn't actually matter because when we re-visited
'x509' on the next iteration via 'x509->signer', it was already seen and
not verified, so we returned -ENOKEY anyway.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <james.l.morris@oracle.com>
If pkcs7_check_authattrs() returns an error code, we should pass that
error code on, rather than using ENOMEM.
Fixes: 99db443506 ("PKCS#7: Appropriately restrict authenticated attributes and content type")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <james.l.morris@oracle.com>
Adding a specially crafted X.509 certificate whose subjectPublicKey
ASN.1 value is zero-length caused x509_extract_key_data() to set the
public key size to SIZE_MAX, as it subtracted the nonexistent BIT STRING
metadata byte. Then, x509_cert_parse() called kmemdup() with that bogus
size, triggering the WARN_ON_ONCE() in kmalloc_slab().
This appears to be harmless, but it still must be fixed since WARNs are
never supposed to be user-triggerable.
Fix it by updating x509_cert_parse() to validate that the value has a
BIT STRING metadata byte, and that the byte is 0 which indicates that
the number of bits in the bitstring is a multiple of 8.
It would be nice to handle the metadata byte in asn1_ber_decoder()
instead. But that would be tricky because in the general case a BIT
STRING could be implicitly tagged, and/or could legitimately have a
length that is not a whole number of bytes.
Here was the WARN (cleaned up slightly):
WARNING: CPU: 1 PID: 202 at mm/slab_common.c:971 kmalloc_slab+0x5d/0x70 mm/slab_common.c:971
Modules linked in:
CPU: 1 PID: 202 Comm: keyctl Tainted: G B 4.14.0-09238-g1d3b78bbc6e9 #26
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-20171110_100015-anatol 04/01/2014
task: ffff880033014180 task.stack: ffff8800305c8000
Call Trace:
__do_kmalloc mm/slab.c:3706 [inline]
__kmalloc_track_caller+0x22/0x2e0 mm/slab.c:3726
kmemdup+0x17/0x40 mm/util.c:118
kmemdup include/linux/string.h:414 [inline]
x509_cert_parse+0x2cb/0x620 crypto/asymmetric_keys/x509_cert_parser.c:106
x509_key_preparse+0x61/0x750 crypto/asymmetric_keys/x509_public_key.c:174
asymmetric_key_preparse+0xa4/0x150 crypto/asymmetric_keys/asymmetric_type.c:388
key_create_or_update+0x4d4/0x10a0 security/keys/key.c:850
SYSC_add_key security/keys/keyctl.c:122 [inline]
SyS_add_key+0xe8/0x290 security/keys/keyctl.c:62
entry_SYSCALL_64_fastpath+0x1f/0x96
Fixes: 42d5ec27f8 ("X.509: Add an ASN.1 decoder")
Cc: <stable@vger.kernel.org> # v3.7+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <james.l.morris@oracle.com>
When chacha20_block() outputs the keystream block, it uses 'u32' stores
directly. However, the callers (crypto/chacha20_generic.c and
drivers/char/random.c) declare the keystream buffer as a 'u8' array,
which is not guaranteed to have the needed alignment.
Fix it by having both callers declare the keystream as a 'u32' array.
For now this is preferable to switching over to the unaligned access
macros because chacha20_block() is only being used in cases where we can
easily control the alignment (stack buffers).
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Now that crypto_chacha20_setkey() and crypto_chacha20_init() use the
unaligned access macros and crypto_xor() also accepts unaligned buffers,
there is no need to have a cra_alignmask set for chacha20-generic.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The generic ChaCha20 implementation has a cra_alignmask of 3, which
ensures that the key passed into crypto_chacha20_setkey() and the IV
passed into crypto_chacha20_init() are 4-byte aligned. However, these
functions are also called from the ARM and ARM64 implementations of
ChaCha20, which intentionally do not have a cra_alignmask set. This is
broken because 32-bit words are being loaded from potentially-unaligned
buffers without the unaligned access macros.
Fix it by using the unaligned access macros when loading the key and IV.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The four 32-bit constants for the initial state of ChaCha20 were loaded
from a char array which is not guaranteed to have the needed alignment.
Fix it by just assigning the constants directly instead.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Make the cryptd queue length configurable. We recently had customer where this
needed to be tuned to accommodate the aesni_intel module and prevent packet
drop.
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Preempt counter APIs have been split out, currently, hardirq.h just
includes irq_enter/exit APIs which are not used by crypto at all.
So, remove the unused hardirq.h.
Signed-off-by: Yang Shi <yang.s@alibaba-inc.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-crypto@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
On 32-bit (e.g. with m68k-linux-gnu-gcc-4.1):
crypto/keywrap.c: In function ‘crypto_kw_decrypt’:
crypto/keywrap.c:191: warning: integer constant is too large for ‘long’ type
crypto/keywrap.c: In function ‘crypto_kw_encrypt’:
crypto/keywrap.c:224: warning: integer constant is too large for ‘long’ type
Fixes: 9e49451d7a ("crypto: keywrap - simplify code")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
A few years ago the FSF moved and "59 Temple Place" is wrong. Having this
still in our source files feels old and unmaintained.
Let's take the license statement serious and not confuse users.
As https://www.gnu.org/licenses/gpl-howto.html suggests, we replace the
postal address with "<http://www.gnu.org/licenses/>".
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If crypto_get_default_rng returns an error, the
function ecc_gen_privkey should return an error.
Instead, it currently tries to use the default_rng
nevertheless, thus creating a kernel panic with a
NULL pointer dereference.
Returning the error directly, as was supposedly
intended when looking at the code, fixes this.
Signed-off-by: Pierre Ducroquet <pinaraf@pinaraf.info>
Reviewed-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In case buffer length is a multiple of PAGE_SIZE,
the S/G table is incorrectly generated.
Fix this by handling buflen = k * PAGE_SIZE separately.
Signed-off-by: Robert Baronescu <robert.baronescu@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When asked to encrypt or decrypt 0 bytes, both the generic and x86
implementations of Salsa20 crash in blkcipher_walk_done(), either when
doing 'kfree(walk->buffer)' or 'free_page((unsigned long)walk->page)',
because walk->buffer and walk->page have not been initialized.
The bug is that Salsa20 is calling blkcipher_walk_done() even when
nothing is in 'walk.nbytes'. But blkcipher_walk_done() is only meant to
be called when a nonzero number of bytes have been provided.
The broken code is part of an optimization that tries to make only one
call to salsa20_encrypt_bytes() to process inputs that are not evenly
divisible by 64 bytes. To fix the bug, just remove this "optimization"
and use the blkcipher_walk API the same way all the other users do.
Reproducer:
#include <linux/if_alg.h>
#include <sys/socket.h>
#include <unistd.h>
int main()
{
int algfd, reqfd;
struct sockaddr_alg addr = {
.salg_type = "skcipher",
.salg_name = "salsa20",
};
char key[16] = { 0 };
algfd = socket(AF_ALG, SOCK_SEQPACKET, 0);
bind(algfd, (void *)&addr, sizeof(addr));
reqfd = accept(algfd, 0, 0);
setsockopt(algfd, SOL_ALG, ALG_SET_KEY, key, sizeof(key));
read(reqfd, key, sizeof(key));
}
Reported-by: syzbot <syzkaller@googlegroups.com>
Fixes: eb6f13eb9f ("[CRYPTO] salsa20_generic: Fix multi-page processing")
Cc: <stable@vger.kernel.org> # v2.6.25+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Because the HMAC template didn't check that its underlying hash
algorithm is unkeyed, trying to use "hmac(hmac(sha3-512-generic))"
through AF_ALG or through KEYCTL_DH_COMPUTE resulted in the inner HMAC
being used without having been keyed, resulting in sha3_update() being
called without sha3_init(), causing a stack buffer overflow.
This is a very old bug, but it seems to have only started causing real
problems when SHA-3 support was added (requires CONFIG_CRYPTO_SHA3)
because the innermost hash's state is ->import()ed from a zeroed buffer,
and it just so happens that other hash algorithms are fine with that,
but SHA-3 is not. However, there could be arch or hardware-dependent
hash algorithms also affected; I couldn't test everything.
Fix the bug by introducing a function crypto_shash_alg_has_setkey()
which tests whether a shash algorithm is keyed. Then update the HMAC
template to require that its underlying hash algorithm is unkeyed.
Here is a reproducer:
#include <linux/if_alg.h>
#include <sys/socket.h>
int main()
{
int algfd;
struct sockaddr_alg addr = {
.salg_type = "hash",
.salg_name = "hmac(hmac(sha3-512-generic))",
};
char key[4096] = { 0 };
algfd = socket(AF_ALG, SOCK_SEQPACKET, 0);
bind(algfd, (const struct sockaddr *)&addr, sizeof(addr));
setsockopt(algfd, SOL_ALG, ALG_SET_KEY, key, sizeof(key));
}
Here was the KASAN report from syzbot:
BUG: KASAN: stack-out-of-bounds in memcpy include/linux/string.h:341 [inline]
BUG: KASAN: stack-out-of-bounds in sha3_update+0xdf/0x2e0 crypto/sha3_generic.c:161
Write of size 4096 at addr ffff8801cca07c40 by task syzkaller076574/3044
CPU: 1 PID: 3044 Comm: syzkaller076574 Not tainted 4.14.0-mm1+ #25
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:17 [inline]
dump_stack+0x194/0x257 lib/dump_stack.c:53
print_address_description+0x73/0x250 mm/kasan/report.c:252
kasan_report_error mm/kasan/report.c:351 [inline]
kasan_report+0x25b/0x340 mm/kasan/report.c:409
check_memory_region_inline mm/kasan/kasan.c:260 [inline]
check_memory_region+0x137/0x190 mm/kasan/kasan.c:267
memcpy+0x37/0x50 mm/kasan/kasan.c:303
memcpy include/linux/string.h:341 [inline]
sha3_update+0xdf/0x2e0 crypto/sha3_generic.c:161
crypto_shash_update+0xcb/0x220 crypto/shash.c:109
shash_finup_unaligned+0x2a/0x60 crypto/shash.c:151
crypto_shash_finup+0xc4/0x120 crypto/shash.c:165
hmac_finup+0x182/0x330 crypto/hmac.c:152
crypto_shash_finup+0xc4/0x120 crypto/shash.c:165
shash_digest_unaligned+0x9e/0xd0 crypto/shash.c:172
crypto_shash_digest+0xc4/0x120 crypto/shash.c:186
hmac_setkey+0x36a/0x690 crypto/hmac.c:66
crypto_shash_setkey+0xad/0x190 crypto/shash.c:64
shash_async_setkey+0x47/0x60 crypto/shash.c:207
crypto_ahash_setkey+0xaf/0x180 crypto/ahash.c:200
hash_setkey+0x40/0x90 crypto/algif_hash.c:446
alg_setkey crypto/af_alg.c:221 [inline]
alg_setsockopt+0x2a1/0x350 crypto/af_alg.c:254
SYSC_setsockopt net/socket.c:1851 [inline]
SyS_setsockopt+0x189/0x360 net/socket.c:1830
entry_SYSCALL_64_fastpath+0x1f/0x96
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
af_alg_free_areq_sgls()
If allocating the ->tsgl member of 'struct af_alg_async_req' failed,
during cleanup we dereferenced the NULL ->tsgl pointer in
af_alg_free_areq_sgls(), because ->tsgl_entries was nonzero.
Fix it by only freeing the ->tsgl list if it is non-NULL.
This affected both algif_skcipher and algif_aead.
Fixes: e870456d8e ("crypto: algif_skcipher - overhaul memory management")
Fixes: d887c52d6a ("crypto: algif_aead - overhaul memory management")
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In the AEAD interface for AF_ALG, the reference to the "null skcipher"
held by each tfm was being dropped in the wrong place -- when each
af_alg_ctx was freed instead of when the aead_tfm was freed. As
discovered by syzkaller, a specially crafted program could use this to
cause the null skcipher to be freed while it is still in use.
Fix it by dropping the reference in the right place.
Fixes: 72548b093e ("crypto: algif_aead - copy AAD from src to dst")
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In rsa_get_n(), if the buffer contained all 0's and "FIPS mode" is
enabled, we would read one byte past the end of the buffer while
scanning the leading zeroes. Fix it by checking 'n_sz' before '!*ptr'.
This bug was reachable by adding a specially crafted key of type
"asymmetric" (requires CONFIG_RSA and CONFIG_X509_CERTIFICATE_PARSER).
KASAN report:
BUG: KASAN: slab-out-of-bounds in rsa_get_n+0x19e/0x1d0 crypto/rsa_helper.c:33
Read of size 1 at addr ffff88003501a708 by task keyctl/196
CPU: 1 PID: 196 Comm: keyctl Not tainted 4.14.0-09238-g1d3b78bbc6e9 #26
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-20171110_100015-anatol 04/01/2014
Call Trace:
rsa_get_n+0x19e/0x1d0 crypto/rsa_helper.c:33
asn1_ber_decoder+0x82a/0x1fd0 lib/asn1_decoder.c:328
rsa_set_pub_key+0xd3/0x320 crypto/rsa.c:278
crypto_akcipher_set_pub_key ./include/crypto/akcipher.h:364 [inline]
pkcs1pad_set_pub_key+0xae/0x200 crypto/rsa-pkcs1pad.c:117
crypto_akcipher_set_pub_key ./include/crypto/akcipher.h:364 [inline]
public_key_verify_signature+0x270/0x9d0 crypto/asymmetric_keys/public_key.c:106
x509_check_for_self_signed+0x2ea/0x480 crypto/asymmetric_keys/x509_public_key.c:141
x509_cert_parse+0x46a/0x620 crypto/asymmetric_keys/x509_cert_parser.c:129
x509_key_preparse+0x61/0x750 crypto/asymmetric_keys/x509_public_key.c:174
asymmetric_key_preparse+0xa4/0x150 crypto/asymmetric_keys/asymmetric_type.c:388
key_create_or_update+0x4d4/0x10a0 security/keys/key.c:850
SYSC_add_key security/keys/keyctl.c:122 [inline]
SyS_add_key+0xe8/0x290 security/keys/keyctl.c:62
entry_SYSCALL_64_fastpath+0x1f/0x96
Allocated by task 196:
__do_kmalloc mm/slab.c:3711 [inline]
__kmalloc_track_caller+0x118/0x2e0 mm/slab.c:3726
kmemdup+0x17/0x40 mm/util.c:118
kmemdup ./include/linux/string.h:414 [inline]
x509_cert_parse+0x2cb/0x620 crypto/asymmetric_keys/x509_cert_parser.c:106
x509_key_preparse+0x61/0x750 crypto/asymmetric_keys/x509_public_key.c:174
asymmetric_key_preparse+0xa4/0x150 crypto/asymmetric_keys/asymmetric_type.c:388
key_create_or_update+0x4d4/0x10a0 security/keys/key.c:850
SYSC_add_key security/keys/keyctl.c:122 [inline]
SyS_add_key+0xe8/0x290 security/keys/keyctl.c:62
entry_SYSCALL_64_fastpath+0x1f/0x96
Fixes: 5a7de97309 ("crypto: rsa - return raw integers for the ASN.1 parser")
Cc: <stable@vger.kernel.org> # v4.8+
Cc: Tudor Ambarus <tudor-dan.ambarus@nxp.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: James Morris <james.l.morris@oracle.com>
Reviewed-by: David Howells <dhowells@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The skcipher_walk_aead_common function calls scatterwalk_copychunks on
the input and output walks to skip the associated data. If the AD end
at an SG list entry boundary, then after these calls the walks will
still be pointing to the end of the skipped region.
These offsets are later checked for alignment in skcipher_walk_next,
so the skcipher_walk may detect the alignment incorrectly.
This patch fixes it by calling scatterwalk_done after the copychunks
calls to ensure that the offsets refer to the right SG list entry.
Fixes: b286d8b1a6 ("crypto: skcipher - Add skcipher walk interface")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ondrej Mosnacek <omosnacek@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The code paths protected by the socket-lock do not use or modify the
socket in a non-atomic fashion. The actions pertaining the socket do not
even need to be handled as an atomic operation. Thus, the socket-lock
can be safely ignored.
This fixes a bug regarding scheduling in atomic as the callback function
may be invoked in interrupt context.
In addition, the sock_hold is moved before the AIO encrypt/decrypt
operation to ensure that the socket is always present. This avoids a
tiny race window where the socket is unprotected and yet used by the AIO
operation.
Finally, the release of resources for a crypto operation is moved into a
common function of af_alg_free_resources.
Cc: <stable@vger.kernel.org>
Fixes: e870456d8e ("crypto: algif_skcipher - overhaul memory management")
Fixes: d887c52d6a ("crypto: algif_aead - overhaul memory management")
Reported-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Tested-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The TX SGL may contain SGL entries that are assigned a NULL page. This
may happen if a multi-stage AIO operation is performed where the data
for each stage is pointed to by one SGL entry. Upon completion of that
stage, af_alg_pull_tsgl will assign NULL to the SGL entry.
The NULL cipher used to copy the AAD from TX SGL to the destination
buffer, however, cannot handle the case where the SGL starts with an SGL
entry having a NULL page. Thus, the code needs to advance the start
pointer into the SGL to the first non-NULL entry.
This fixes a crash visible on Intel x86 32 bit using the libkcapi test
suite.
Cc: <stable@vger.kernel.org>
Fixes: 72548b093e ("crypto: algif_aead - copy AAD from src to dst")
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Convert all allocations that used a NOTRACK flag to stop using it.
Link: http://lkml.kernel.org/r/20171007030159.22241-3-alexander.levin@verizon.com
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tim Hansen <devtimhansen@gmail.com>
Cc: Vegard Nossum <vegardno@ifi.uio.no>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Set the module licence to prevent the kernel from being tainted if loaded
as a module.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 4.15:
API:
- Disambiguate EBUSY when queueing crypto request by adding ENOSPC.
This change touches code outside the crypto API.
- Reset settings when empty string is written to rng_current.
Algorithms:
- Add OSCCA SM3 secure hash.
Drivers:
- Remove old mv_cesa driver (replaced by marvell/cesa).
- Enable rfc3686/ecb/cfb/ofb AES in crypto4xx.
- Add ccm/gcm AES in crypto4xx.
- Add support for BCM7278 in iproc-rng200.
- Add hash support on Exynos in s5p-sss.
- Fix fallback-induced error in vmx.
- Fix output IV in atmel-aes.
- Fix empty GCM hash in mediatek.
Others:
- Fix DoS potential in lib/mpi.
- Fix potential out-of-order issues with padata"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (162 commits)
lib/mpi: call cond_resched() from mpi_powm() loop
crypto: stm32/hash - Fix return issue on update
crypto: dh - Remove pointless checks for NULL 'p' and 'g'
crypto: qat - Clean up error handling in qat_dh_set_secret()
crypto: dh - Don't permit 'key' or 'g' size longer than 'p'
crypto: dh - Don't permit 'p' to be 0
crypto: dh - Fix double free of ctx->p
hwrng: iproc-rng200 - Add support for BCM7278
dt-bindings: rng: Document BCM7278 RNG200 compatible
crypto: chcr - Replace _manual_ swap with swap macro
crypto: marvell - Add a NULL entry at the end of mv_cesa_plat_id_table[]
hwrng: virtio - Virtio RNG devices need to be re-registered after suspend/resume
crypto: atmel - remove empty functions
crypto: ecdh - remove empty exit()
MAINTAINERS: update maintainer for qat
crypto: caam - remove unused param of ctx_map_to_sec4_sg()
crypto: caam - remove unneeded edesc zeroization
crypto: atmel-aes - Reset the controller before each use
crypto: atmel-aes - properly set IV after {en,de}crypt
hwrng: core - Reset user selected rng by writing "" to rng_current
...
Neither 'p' nor 'g' can be NULL, as they were unpacked using
crypto_dh_decode_key(). And it makes no sense for them to be optional.
So remove the NULL checks that were copy-and-pasted into both modules.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The "qat-dh" DH implementation assumes that 'key' and 'g' can be copied
into a buffer with size 'p_size'. However it was never checked that
that was actually the case, which most likely allowed users to cause a
buffer underflow via KEYCTL_DH_COMPUTE.
Fix this by updating crypto_dh_decode_key() to verify this precondition
for all DH implementations.
Fixes: c9839143eb ("crypto: qat - Add DH support")
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull crypto fixes from Herbert Xu:
"This fixes an unaligned panic in x86/sha-mb and a bug in ccm that
triggers with certain underlying implementations"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: ccm - preserve the IV buffer
crypto: x86/sha1-mb - fix panic due to unaligned access
crypto: x86/sha256-mb - fix panic due to unaligned access
Pointer members of an object with static storage duration, if not
explicitly initialized, will be initialized to a NULL pointer. The crypto
API checks if this pointer is not NULL before using it, we are safe to
remove the function.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
tcrypt starts several async crypto ops and waits for their completions.
Move it over to generic code doing the same.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
testmgr is starting async. crypto ops and waiting for them to complete.
Move it over to generic code doing the same.
This also provides a test of the generic crypto async. wait code.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
gcm is starting an async. crypto op and waiting for it complete.
Move it over to generic code doing the same.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
DRBG is starting an async. crypto op and waiting for it complete.
Move it over to generic code doing the same.
The code now also passes CRYPTO_TFM_REQ_MAY_SLEEP flag indicating
crypto request memory allocation may use GFP_KERNEL which should
be perfectly fine as the code is obviously sleeping for the
completion of the request any way.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
public_key_verify_signature() is starting an async crypto op and
waiting for it to complete. Move it over to generic code doing
the same.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
algif starts several async crypto ops and waits for their completion.
Move it over to generic code doing the same.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Invoking a possibly async. crypto op and waiting for completion
while correctly handling backlog processing is a common task
in the crypto API implementation and outside users of it.
This patch adds a generic implementation for doing so in
preparation for using it across the board instead of hand
rolled versions.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
CC: Eric Biggers <ebiggers3@gmail.com>
CC: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Now that -EBUSY return code only indicates backlog queueing
we can safely remove the now redundant check for the
CRYPTO_TFM_REQ_MAY_BACKLOG flag when -EBUSY is returned.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The crypto API was using the -EBUSY return value to indicate
both a hard failure to submit a crypto operation into a
transformation provider when the latter was busy and the backlog
mechanism was not enabled as well as a notification that the
operation was queued into the backlog when the backlog mechanism
was enabled.
Having the same return code indicate two very different conditions
depending on a flag is both error prone and requires extra runtime
check like the following to discern between the cases:
if (err == -EINPROGRESS ||
(err == -EBUSY && (ahash_request_flags(req) &
CRYPTO_TFM_REQ_MAY_BACKLOG)))
This patch changes the return code used to indicate a crypto op
failed due to the transformation provider being transiently busy
to -ENOSPC.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix the way the length of the buffers used for
encryption / decryption are computed.
For e.g. in case of encryption, input buffer does not contain
an authentication tag.
Signed-off-by: Robert Baronescu <robert.baronescu@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-crypto@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
It multiply GF(2^128) elements in the ble format.
It will be used by chelsio driver to speed up gf multiplication.
Signed-off-by: Harsh Jain <harsh@chelsio.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The IV buffer used during CCM operations is used twice, during both the
hashing step and the ciphering step.
When using a hardware accelerator that updates the contents of the IV
buffer at the end of ciphering operations, the value will be modified.
In the decryption case, the subsequent setup of the hashing algorithm
will interpret the updated IV instead of the original value, which can
lead to out-of-bounds writes.
Reuse the idata buffer, only used in the hashing step, to preserve the
IV's value during the ciphering step in the decryption case.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ASN.1 parser does not necessarily set the sinfo field,
this patch prevents a NULL pointer dereference on broken
input.
Fixes: 99db443506 ("PKCS#7: Appropriately restrict authenticated attributes and content type")
Signed-off-by: Eric Sesterhenn <eric.sesterhenn@x41-dsec.de>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: stable@vger.kernel.org # 4.3+
For finding asymmetric key, the input id_0 and id_1 parameters can
not be NULL at the same time. This patch adds the BUG_ON checking
for id_0 and id_1.
Cc: David Howells <dhowells@redhat.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Chun-Yi Lee <jlee@suse.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Fix the wrong index number when checking the existence of second
id in function of finding asymmetric key. The id_1 is the second
id that the index in array must be 1 but not 0.
Fixes: 9eb029893a (KEYS: Generalise x509_request_asymmetric_key())
Cc: David Howells <dhowells@redhat.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Chun-Yi Lee <jlee@suse.com>
Signed-off-by: David Howells <dhowells@redhat.com>
The code is simplified by using two __be64 values for the operation
instead of using two arrays of u8. This allows to get rid of the memory
alignment code. In addition, the crypto_xor can be replaced with a
native XOR operation. Finally, the definition of the variables is
re-arranged such that the data structures come before simple variables
to potentially reduce memory space.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
DH_KPP_SECRET_MIN_SIZE and dh_data_size() are both returning
unsigned values.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
p->key_size, p->p_size, p->g_size are all of unsigned int type.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
ECDH_KPP_SECRET_MIN_SIZE and params->key_size are both returning
unsigned values.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If the cipher name does not start with 'ecb(' we should bail out, as done
in the 'create()' function in 'crypto/xts.c'.
Fixes: 700cb3f5fe ("crypto: lrw - Convert to skcipher")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
All error handling paths 'goto err_drop_spawn' except this one.
In order to avoid some resources leak, we should do it as well here.
Fixes: 700cb3f5fe ("crypto: lrw - Convert to skcipher")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The shash ahash digest adaptor function may crash if given a
zero-length input together with a null SG list. This is because
it tries to read the SG list before looking at the length.
This patch fixes it by checking the length first.
Cc: <stable@vger.kernel.org>
Reported-by: Stephan Müller<smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Stephan Müller <smueller@chronox.de>
The variable len is set to zero, never read and then later updated
to p - name, so clearly the zero'ing of len is redundant and
can be removed.
Detected by clang scan-build:
" warning: Value stored to 'len' is never read"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The skcipher walk interface doesn't handle zero-length input
properly as the old blkcipher walk interface did. This is due
to the fact that the length check is done too late.
This patch moves the length check forward so that it does the
right thing.
Fixes: b286d8b1a6 ("crypto: skcipher - Add skcipher walk...")
Cc: <stable@vger.kernel.org>
Reported-by: Stephan Müller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The SCTP program may sleep under a spinlock, and the function call path is:
sctp_generate_t3_rtx_event (acquire the spinlock)
sctp_do_sm
sctp_side_effects
sctp_cmd_interpreter
sctp_make_init_ack
sctp_pack_cookie
crypto_shash_setkey
shash_setkey_unaligned
kmalloc(GFP_KERNEL)
For the same reason, the orinoco driver may sleep in interrupt handler,
and the function call path is:
orinoco_rx_isr_tasklet
orinoco_rx
orinoco_mic
crypto_shash_setkey
shash_setkey_unaligned
kmalloc(GFP_KERNEL)
To fix it, GFP_KERNEL is replaced with GFP_ATOMIC.
This bug is found by my static analysis tool and my code review.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
All error handling paths 'goto err_drop_spawn' except this one.
In order to avoid some resources leak, we should do it as well here.
Fixes: f1c131b454 ("crypto: xts - Convert to skcipher")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch replace GCM IV size value by their constant name.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add testmgr and tcrypt tests and vectors for SM3 secure hash.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When two adjacent TX SGL are processed and parts of both TX SGLs
are pulled into the per-request TX SGL, the wrong per-request
TX SGL entries were updated.
This fixes a NULL pointer dereference when a cipher implementation walks
the TX SGL where some of the SGL entries were NULL.
Fixes: e870456d8e ("crypto: algif_skcipher - overhaul memory...")
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
During the change to use aligned buffers, the deallocation code path was
not updated correctly. The current code tries to free the aligned buffer
pointer and not the original buffer pointer as it is supposed to.
Thus, the code is updated to free the original buffer pointer and set
the aligned buffer pointer that is used throughout the code to NULL.
Fixes: 3cfc3b9721 ("crypto: drbg - use aligned buffers")
CC: <stable@vger.kernel.org>
CC: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When a page is assigned to a TX SGL, call get_page to increment the
reference counter. It is possible that one page is referenced in
multiple SGLs:
- in the global TX SGL in case a previous af_alg_pull_tsgl only
reassigned parts of a page to a per-request TX SGL
- in the per-request TX SGL as assigned by af_alg_pull_tsgl
Note, multiple requests can be active at the same time whose TX SGLs all
point to different parts of the same page.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There are already helpers to (un)register multiple normal
and AEAD algos. Add one for ahashes too.
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For asynchronous operation, SGs are allocated without a page mapped to
them or with a page that is not used (ref-counted). If the SGL is freed,
the code must only call put_page for an SG if there was a page assigned
and ref-counted in the first place.
This fixes a kernel crash when using io_submit with more than one iocb
using the sendmsg and sendpage (vmsplice/splice) interface.
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
We failed to catch a bug in the chacha20 code after porting it to the
skcipher API. We would have caught it if any chunked tests had been
defined, so define some now so we will catch future regressions.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Commit 9ae433bc79 ("crypto: chacha20 - convert generic and x86 versions
to skcipher") ported the existing chacha20 code to use the new skcipher
API, and introduced a bug along the way. Unfortunately, the tcrypt tests
did not catch the error, and it was only found recently by Tobias.
Stefan kindly diagnosed the error, and proposed a fix which is similar
to the one below, with the exception that 'walk.stride' is used rather
than the hardcoded block size. This does not actually matter in this
case, but it's a better example of how to use the skcipher walk API.
Fixes: 9ae433bc79 ("crypto: chacha20 - convert generic and x86 ...")
Cc: <stable@vger.kernel.org> # v4.11+
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Reported-by: Tobias Brunner <tobias@strongswan.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Consolidate following data structures:
skcipher_async_req, aead_async_req -> af_alg_async_req
skcipher_rsgl, aead_rsql -> af_alg_rsgl
skcipher_tsgl, aead_tsql -> af_alg_tsgl
skcipher_ctx, aead_ctx -> af_alg_ctx
Consolidate following functions:
skcipher_sndbuf, aead_sndbuf -> af_alg_sndbuf
skcipher_writable, aead_writable -> af_alg_writable
skcipher_rcvbuf, aead_rcvbuf -> af_alg_rcvbuf
skcipher_readable, aead_readable -> af_alg_readable
aead_alloc_tsgl, skcipher_alloc_tsgl -> af_alg_alloc_tsgl
aead_count_tsgl, skcipher_count_tsgl -> af_alg_count_tsgl
aead_pull_tsgl, skcipher_pull_tsgl -> af_alg_pull_tsgl
aead_free_areq_sgls, skcipher_free_areq_sgls -> af_alg_free_areq_sgls
aead_wait_for_wmem, skcipher_wait_for_wmem -> af_alg_wait_for_wmem
aead_wmem_wakeup, skcipher_wmem_wakeup -> af_alg_wmem_wakeup
aead_wait_for_data, skcipher_wait_for_data -> af_alg_wait_for_data
aead_data_wakeup, skcipher_data_wakeup -> af_alg_data_wakeup
aead_sendmsg, skcipher_sendmsg -> af_alg_sendmsg
aead_sendpage, skcipher_sendpage -> af_alg_sendpage
aead_async_cb, skcipher_async_cb -> af_alg_async_cb
aead_poll, skcipher_poll -> af_alg_poll
Split out the following common code from recvmsg:
af_alg_alloc_areq: allocation of the request data structure for the
cipher operation
af_alg_get_rsgl: creation of the RX SGL anchored in the request data
structure
The following changes to the implementation without affecting the
functionality have been applied to synchronize slightly different code
bases in algif_skcipher and algif_aead:
The wakeup in af_alg_wait_for_data is triggered when either more data
is received or the indicator that more data is to be expected is
released. The first is triggered by user space, the second is
triggered by the kernel upon finishing the processing of data
(i.e. the kernel is ready for more).
af_alg_sendmsg uses size_t in min_t calculation for obtaining len.
Return code determination is consistent with algif_skcipher. The
scope of the variable i is reduced to match algif_aead. The type of the
variable i is switched from int to unsigned int to match algif_aead.
af_alg_sendpage does not contain the superfluous err = 0 from
aead_sendpage.
af_alg_async_cb requires to store the number of output bytes in
areq->outlen before the AIO callback is triggered.
The POLLIN / POLLRDNORM is now set when either not more data is given or
the kernel is supplied with data. This is consistent to the wakeup from
sleep when the kernel waits for data.
The request data structure is extended by the field last_rsgl which
points to the last RX SGL list entry. This shall help recvmsg
implementation to chain the RX SGL to other SG(L)s if needed. It is
currently used by algif_aead which chains the tag SGL to the RX SGL
during decryption.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When UBSAN is enabled, we get a very large stack frame for
__serpent_setkey, when the register allocator ends up using more registers
than it has, and has to spill temporary values to the stack. The code
was originally optimized for in-order x86-32 CPU implementations using
older compilers, but it now runs into a highly suboptimal case on all
CPU architectures, as seen by this warning:
crypto/serpent_generic.c: In function '__serpent_setkey':
crypto/serpent_generic.c:436:1: error: the frame size of 2720 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
Disabling -fsanitize=alignment would avoid that warning, presumably the
option turns off a optimization step that is required for getting the
register allocation right, but there is no easy way to do that on gcc-7
(gcc-8 introduces a function attribute for this).
I tried to figure out a way to modify the source code instead, and noticed
that the two stages of the setkey() function (keyiter and sbox) each are
fine by themselves, but not when combined into one function. Splitting
out the entire sbox into a separate function also happens to work fine
with all compilers I tried (arm, arm64 and x86).
The setkey function uses a strange way to handle offsets into the key
array, using both negative and positive index values, as well as adjusting
the array pointer back and forth. I have checked that this actually
makes no difference to modern compilers, but I left that untouched
to make the patch easier to review and to keep the code closer to
the reference implementation.
Link: https://patchwork.kernel.org/patch/9189575/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use the NULL cipher to copy the AAD and PT/CT from the TX SGL
to the RX SGL. This allows an in-place crypto operation on the
RX SGL for encryption, because the TX data is always smaller or
equal to the RX data (the RX data will hold the tag).
For decryption, a per-request TX SGL is created which will only hold
the tag value. As the RX SGL will have no space for the tag value and
an in-place operation will not write the tag buffer, the TX SGL with the
tag value is chained to the RX SGL. This now allows an in-place
crypto operation.
For example:
* without the patch:
kcapi -x 2 -e -c "gcm(aes)" -p 89154d0d4129d322e4487bafaa4f6b46 -k c0ece3e63198af382b5603331cc23fa8 -i 7e489b83622e7228314d878d -a afcd7202d621e06ca53b70c2bdff7fb2 -l 16 -u -s
00000000000000000000000000000000f4a3eacfbdadd3b1a17117b1d67ffc1f1e21efbbc6d83724a8c296e3bb8cda0c
* with the patch:
kcapi -x 2 -e -c "gcm(aes)" -p 89154d0d4129d322e4487bafaa4f6b46 -k c0ece3e63198af382b5603331cc23fa8 -i 7e489b83622e7228314d878d -a afcd7202d621e06ca53b70c2bdff7fb2 -l 16 -u -s
afcd7202d621e06ca53b70c2bdff7fb2f4a3eacfbdadd3b1a17117b1d67ffc1f1e21efbbc6d83724a8c296e3bb8cda0c
Tests covering this functionality have been added to libkcapi.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If no data has been processed during recvmsg, return the error code.
This covers all errors received during non-AIO operations.
If any error occurs during a synchronous operation in addition to
-EIOCBQUEUED or -EBADMSG (like -ENOMEM), it should be relayed to the
caller.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There are quite a number of occurrences in the kernel of the pattern
if (dst != src)
memcpy(dst, src, walk.total % AES_BLOCK_SIZE);
crypto_xor(dst, final, walk.total % AES_BLOCK_SIZE);
or
crypto_xor(keystream, src, nbytes);
memcpy(dst, keystream, nbytes);
where crypto_xor() is preceded or followed by a memcpy() invocation
that is only there because crypto_xor() uses its output parameter as
one of the inputs. To avoid having to add new instances of this pattern
in the arm64 code, which will be refactored to implement non-SIMD
fallbacks, add an alternative implementation called crypto_xor_cpy(),
taking separate input and output arguments. This removes the need for
the separate memcpy().
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In preparation of introducing crypto_xor_cpy(), which will use separate
operands for input and output, modify the __crypto_xor() implementation,
which it will share with the existing crypto_xor(), which provides the
actual functionality when not using the inline version.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The scompress code allocates 2 x 128 KB of scratch buffers for each CPU,
so that clients of the async API can use synchronous implementations
even from atomic context. However, on systems such as Cavium Thunderx
(which has 96 cores), this adds up to a non-negligible 24 MB. Also,
32-bit systems may prefer to use their precious vmalloc space for other
things,especially since there don't appear to be any clients for the
async compression API yet.
So let's defer allocation of the scratch buffers until the first time
we allocate an acompress cipher based on an scompress implementation.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When allocating the per-CPU scratch buffers, we allocate the source
and destination buffers separately, but bail immediately if the second
allocation fails, without freeing the first one. Fix that.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Due to the use of per-CPU buffers, scomp_acomp_comp_decomp() executes
with preemption disabled, and so whether the CRYPTO_TFM_REQ_MAY_SLEEP
flag is set is irrelevant, since we cannot sleep anyway. So disregard
the flag, and use GFP_ATOMIC unconditionally.
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
ecdh_ctx contained static allocated data for the shared secret
and public key.
The shared secret and the public key were doomed to concurrency
issues because they could be shared by multiple crypto requests.
The concurrency is fixed by replacing per-tfm shared secret and
public key with per-request dynamically allocated shared secret
and public key.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Remove xts(aes) speed tests with 2 x 192-bit keys, since implementations
adhering strictly to IEEE 1619-2007 standard cannot cope with key sizes
other than 2 x 128, 2 x 256 bits - i.e. AES-XTS-{128,256}:
[...]
tcrypt: test 5 (384 bit key, 16 byte blocks):
caam_jr 8020000.jr: key size mismatch
tcrypt: setkey() failed flags=200000
[...]
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Otherwise, we might be seeding the RNG using bad randomness, which is
dangerous. The one use of this function from within the kernel -- not
from userspace -- is being removed (keys/big_key), so that call site
isn't relevant in assessing this.
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The updated memory management is described in the top part of the code.
As one benefit of the changed memory management, the AIO and synchronous
operation is now implemented in one common function. The AF_ALG
operation uses the async kernel crypto API interface for each cipher
operation. Thus, the only difference between the AIO and sync operation
types visible from user space is:
1. the callback function to be invoked when the asynchronous operation
is completed
2. whether to wait for the completion of the kernel crypto API operation
or not
The change includes the overhaul of the TX and RX SGL handling. The TX
SGL holding the data sent from user space to the kernel is now dynamic
similar to algif_skcipher. This dynamic nature allows a continuous
operation of a thread sending data and a second thread receiving the
data. These threads do not need to synchronize as the kernel processes
as much data from the TX SGL to fill the RX SGL.
The caller reading the data from the kernel defines the amount of data
to be processed. Considering that the interface covers AEAD
authenticating ciphers, the reader must provide the buffer in the
correct size. Thus the reader defines the encryption size.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The updated memory management is described in the top part of the code.
As one benefit of the changed memory management, the AIO and synchronous
operation is now implemented in one common function. The AF_ALG
operation uses the async kernel crypto API interface for each cipher
operation. Thus, the only difference between the AIO and sync operation
types visible from user space is:
1. the callback function to be invoked when the asynchronous operation
is completed
2. whether to wait for the completion of the kernel crypto API operation
or not
In addition, the code structure is adjusted to match the structure of
algif_aead for easier code assessment.
The user space interface changed slightly as follows: the old AIO
operation returned zero upon success and < 0 in case of an error to user
space. As all other AF_ALG interfaces (including the sync skcipher
interface) returned the number of processed bytes upon success and < 0
in case of an error, the new skcipher interface (regardless of AIO or
sync) returns the number of processed bytes in case of success.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When authencesn is used together with digest_null a crash will
occur on the decrypt path. This is because normally we perform
a special setup to preserve the ESN, but this is skipped if there
is no authentication. However, on the post-authentication path
it always expects the preservation to be in place, thus causing
a crash when digest_null is used.
This patch fixes this by also skipping the post-processing when
there is no authentication.
Fixes: 104880a6b4 ("crypto: authencesn - Convert to new AEAD...")
Cc: <stable@vger.kernel.org>
Reported-by: Jan Tluka <jtluka@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull crypto fixes from Herbert Xu:
- fix new compiler warnings in cavium
- set post-op IV properly in caam (this fixes chaining)
- fix potential use-after-free in atmel in case of EBUSY
- fix sleeping in softirq path in chcr
- disable buggy sha1-avx2 driver (may overread and page fault)
- fix use-after-free on signals in caam
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: cavium - make several functions static
crypto: chcr - Avoid algo allocation in softirq.
crypto: caam - properly set IV after {en,de}crypt
crypto: atmel - only treat EBUSY as transient if backlog
crypto: af_alg - Avoid sock_graft call warning
crypto: caam - fix signals handling
crypto: sha1-ssse3 - Disable avx2
crypto: af_alg - Avoid sock_graft call warning
The newly added sock_graft warning triggers in af_alg_accept.
It's harmless as we're essentially doing sock->sk = sock->sk.
The sock_graft call is actually redundant because all the work
it does is subsumed by sock_init_data. However, it was added
to placate SELinux as it uses it to initialise its internal state.
This patch avoisd the warning by making the SELinux call directly.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: David S. Miller <davem@davemloft.net>
- removal of AVR32 support in dw driver as AVR32 is gone
- new driver for Broadcom stream buffer accelerator (SBA) RAID driver
- add support for Faraday Technology FTDMAC020 in amba-pl08x driver
- IOMMU support in pl330 driver
- updates to bunch of drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJZYG73AAoJEHwUBw8lI4NH+DoP/1f0TsYrQFCjNqa4nybjU1Sd
bbqnpouuJscwt8Qk2LGuSimi0QG91gQOLvrmueFbXtEg86nPOfa0RnWGNF4qwYFK
oliDlXF2PnV65J5kl7CvqXCj6bFiXCULVdO9JD2HFoFB1+lzXN9JQqOG5ne29BQ6
g3HNRlUTXNzQXWisgbAOLxuuvyfv68Zo3wCLYLkd4vC/C4zmxM+KXUG8+s0hS7t3
AOUpYW6F/C+y1Ax+SiACm0QGNZ4rc6/+ZUIIXUO5CfTYGjv6QUdzxiLHtc4br25l
2CoN9IP4V/OxHaW9T1jA61TeAAFr63oXYfDMBBzclzVryZRAIU72ups31uRQXpFz
99zUQ0OsdOCvy0oPInhNd8u+cpyh/4e2RDgSZ9rxw3xVaKFh8lsw5OtcCBQzCMeI
xgFCUBHsLjEi4uafJcl6n2T7+Y4Y0KgOmxPHZo3tpq/2a5M6tVy8k68m3afCQylF
1SOxzVZdDRUutPpviQWop6RgP0EcVuzaUJ0vO4nat4j77vuimaPqdk+oLV46XP2d
5I52kcvbVI4BbJavTjVs3FRdcez0pW37iOw+5MOxHE3dnBp4X/3btFzBY4aOsdg0
wVut3B+9U4WHDBF2ConBxxMvGqMYmcssOQ096GdC6oBHHS7x6n7tEVPiZ5iUacn5
LB8k9AZtpBC7nUWPH7FS
=srPZ
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.13-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- removal of AVR32 support in dw driver as AVR32 is gone
- new driver for Broadcom stream buffer accelerator (SBA) RAID driver
- add support for Faraday Technology FTDMAC020 in amba-pl08x driver
- IOMMU support in pl330 driver
- updates to bunch of drivers
* tag 'dmaengine-4.13-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (36 commits)
dmaengine: qcom_hidma: correct API violation for submit
dmaengine: zynqmp_dma: Remove max len check in zynqmp_dma_prep_memcpy
dmaengine: tegra-apb: Really fix runtime-pm usage
dmaengine: fsl_raid: make of_device_ids const.
dmaengine: qcom_hidma: allow ACPI/DT parameters to be overridden
dmaengine: fsldma: set BWC, DAHTS and SAHTS values correctly
dmaengine: Kconfig: Simplify the help text for MXS_DMA
dmaengine: pl330: Delete unused functions
dmaengine: Replace WARN_TAINT_ONCE() with pr_warn_once()
dmaengine: Kconfig: Extend the dependency for MXS_DMA
dmaengine: mxs: Use %zu for printing a size_t variable
dmaengine: ste_dma40: Cleanup scatterlist layering violations
dmaengine: imx-dma: cleanup scatterlist layering violations
dmaengine: use proper name for the R-Car SoC
dmaengine: imx-sdma: Fix compilation warning.
dmaengine: imx-sdma: Handle return value of clk_prepare_enable
dmaengine: pl330: Add IOMMU support to slave tranfers
dmaengine: DW DMAC: Handle return value of clk_prepare_enable
dmaengine: pl08x: use GENMASK() to create bitmasks
dmaengine: pl08x: Add support for Faraday Technology FTDMAC020
...
Pull networking updates from David Miller:
"Reasonably busy this cycle, but perhaps not as busy as in the 4.12
merge window:
1) Several optimizations for UDP processing under high load from
Paolo Abeni.
2) Support pacing internally in TCP when using the sch_fq packet
scheduler for this is not practical. From Eric Dumazet.
3) Support mutliple filter chains per qdisc, from Jiri Pirko.
4) Move to 1ms TCP timestamp clock, from Eric Dumazet.
5) Add batch dequeueing to vhost_net, from Jason Wang.
6) Flesh out more completely SCTP checksum offload support, from
Davide Caratti.
7) More plumbing of extended netlink ACKs, from David Ahern, Pablo
Neira Ayuso, and Matthias Schiffer.
8) Add devlink support to nfp driver, from Simon Horman.
9) Add RTM_F_FIB_MATCH flag to RTM_GETROUTE queries, from Roopa
Prabhu.
10) Add stack depth tracking to BPF verifier and use this information
in the various eBPF JITs. From Alexei Starovoitov.
11) Support XDP on qed device VFs, from Yuval Mintz.
12) Introduce BPF PROG ID for better introspection of installed BPF
programs. From Martin KaFai Lau.
13) Add bpf_set_hash helper for TC bpf programs, from Daniel Borkmann.
14) For loads, allow narrower accesses in bpf verifier checking, from
Yonghong Song.
15) Support MIPS in the BPF selftests and samples infrastructure, the
MIPS eBPF JIT will be merged in via the MIPS GIT tree. From David
Daney.
16) Support kernel based TLS, from Dave Watson and others.
17) Remove completely DST garbage collection, from Wei Wang.
18) Allow installing TCP MD5 rules using prefixes, from Ivan
Delalande.
19) Add XDP support to Intel i40e driver, from Björn Töpel
20) Add support for TC flower offload in nfp driver, from Simon
Horman, Pieter Jansen van Vuuren, Benjamin LaHaise, Jakub
Kicinski, and Bert van Leeuwen.
21) IPSEC offloading support in mlx5, from Ilan Tayari.
22) Add HW PTP support to macb driver, from Rafal Ozieblo.
23) Networking refcount_t conversions, From Elena Reshetova.
24) Add sock_ops support to BPF, from Lawrence Brako. This is useful
for tuning the TCP sockopt settings of a group of applications,
currently via CGROUPs"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1899 commits)
net: phy: dp83867: add workaround for incorrect RX_CTRL pin strap
dt-bindings: phy: dp83867: provide a workaround for incorrect RX_CTRL pin strap
cxgb4: Support for get_ts_info ethtool method
cxgb4: Add PTP Hardware Clock (PHC) support
cxgb4: time stamping interface for PTP
nfp: default to chained metadata prepend format
nfp: remove legacy MAC address lookup
nfp: improve order of interfaces in breakout mode
net: macb: remove extraneous return when MACB_EXT_DESC is defined
bpf: add missing break in for the TCP_BPF_SNDCWND_CLAMP case
bpf: fix return in load_bpf_file
mpls: fix rtm policy in mpls_getroute
net, ax25: convert ax25_cb.refcount from atomic_t to refcount_t
net, ax25: convert ax25_route.refcount from atomic_t to refcount_t
net, ax25: convert ax25_uid_assoc.refcount from atomic_t to refcount_t
net, sctp: convert sctp_ep_common.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_transport.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_chunk.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_datamsg.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_auth_bytes.refcnt from atomic_t to refcount_t
...
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
This patch uses refcount_inc_not_zero() instead of
atomic_inc_not_zero_hint() due to absense of a _hint()
version of refcount API. If the hint() version must
be used, we might need to revisit API.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The combination of sha1 and aes was disabled in FIPS Mode
accidentally. This patch reenables it.
Fixes: 284a0f6e87 ("crypto: testmgr - Disable fips-allowed for...")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Stephan Müller <smueller@chronox.de>
The PKCS#1 RSA implementation is provided with a self test with RSA 2048
and SHA-256. This self test implicitly covers other RSA keys and other
hashes. Also, this self test implies that the pkcs1pad(rsa) is FIPS
140-2 compliant.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Otherwise, we enable all sorts of forgeries via timing attack.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Suggested-by: Stephan Müller <smueller@chronox.de>
Cc: stable@vger.kernel.org
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: linux-crypto@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
By adding a struct device *dev to struct engine, we could store the
device used at register time and so use all dev_xxx functions instead of
pr_xxx.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix inconsistent format and spelling in hash tests error messages.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
mix_columns() contains a comment which shows the matrix used by the
MixColumns step of AES, but the last entry in this matrix was incorrect
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The test considers a party that already has a private-public
key pair and a party that provides a NULL key. The kernel will
generate the private-public key pair for the latter, computes
the shared secret on both ends and verifies if it's the same.
The explicit private-public key pair was copied from
the previous test vector.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for generating ecc private keys.
Generation of ecc private keys is helpful in a user-space to kernel
ecdh offload because the keys are not revealed to user-space. Private
key generation is also helpful to implement forward secrecy.
If the user provides a NULL ecc private key, the kernel will generate it
and further use it for ecdh.
Move ecdh's object files below drbg's. drbg must be present in the kernel
at the time of calling.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Stephan Müller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
We forgot to set the error code on this path so it could result in
returning NULL which leads to a NULL dereference.
Fixes: db6c43bd21 ("crypto: KEYS: convert public key and digsig asym to the akcipher api")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
crypto_akcipher_maxsize() asks for the output buffer size without
caring for errors. It allways assume that will be called after
a valid setkey. Comply with it and return what he wants.
crypto_akcipher_maxsize() now returns an unsigned int.
Remove the unnecessary check.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
crypto_akcipher_maxsize() asks for the output buffer size without
caring for errors. It allways assume that will be called after
a valid setkey. Comply with it and return what he wants.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
crypto_kpp_maxsize() asks for the output buffer size without
caring for errors. It allways assume that will be called after
a valid setkey. Comply with it and return what he wants.
nbytes has no sense now, remove it and directly return the maxsize.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
crypto_kpp_maxsize() asks for the output buffer size without
caring for errors. It allways assume that will be called after
a valid setkey. Comply with it and return what he wants.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
setkey can be called multiple times during the existence
of the transformation object. In case of multiple setkey calls,
the old key was not freed and we leaked memory.
Free the old MPI key if any.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Rename ecdh_make_pub_key() to ecc_make_pub_key().
ecdh_make_pub_key() is not dh specific and the reference
to dh is wrong.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
ecc software implementation works with chunks of u64 data. There were some
unnecessary casts to u8 and then back to u64 for the ecc keys. This patch
removes the unnecessary casts.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This fixes the following warning when building with clang:
crypto/rng.c:35:34: error: unused function '__crypto_rng_cast'
[-Werror,-Wunused-function]
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
We forgot to set the error code on this path so it could result in
returning NULL which leads to a NULL dereference.
Fixes: db6c43bd21 ("crypto: KEYS: convert public key and digsig asym to the akcipher api")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Many HMAC users directly use directly 0x36/0x5c values.
It's better with crypto to use a name instead of directly some crypto
constant.
This patch simply add HMAC_IPAD_VALUE/HMAC_OPAD_VALUE defines in a new
include file "crypto/hmac.h" and use them in crypto/hmac.c
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
crypto_gcm_setkey() was using wait_for_completion_interruptible() to
wait for completion of async crypto op but if a signal occurs it
may return before DMA ops of HW crypto provider finish, thus
corrupting the data buffer that is kfree'ed in this case.
Resolve this by using wait_for_completion() instead.
Reported-by: Eric Biggers <ebiggers3@gmail.com>
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
CC: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
drbg_kcapi_sym_ctr() was using wait_for_completion_interruptible() to
wait for completion of async crypto op but if a signal occurs it
may return before DMA ops of HW crypto provider finish, thus
corrupting the output buffer.
Resolve this by using wait_for_completion() instead.
Reported-by: Eric Biggers <ebiggers3@gmail.com>
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
CC: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
public_key_verify_signature() was passing the CRYPTO_TFM_REQ_MAY_BACKLOG
flag to akcipher_request_set_callback() but was not handling correctly
the case where a -EBUSY error could be returned from the call to
crypto_akcipher_verify() if backlog was used, possibly casuing
data corruption due to use-after-free of buffers.
Resolve this by handling -EBUSY correctly.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
CC: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The tcrypt AEAD cycles speed tests disables irqs during the test, which is
broken at the very least since commit
'1425d2d17f7309c6 ("crypto: tcrypt - Fix AEAD speed tests")'
adds a wait for completion as part of the test and probably since
switching to the new AEAD API.
While the result of taking a cycle count diff may not mean much on SMP
systems if the task migrates, it's good enough for tcrypt being the quick
& dirty dev tool it is. It's also what all the other (i.e. hash) cycle
speed tests do.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Reported-by: Ofir Drang <ofir.drang@arm.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The API setkey checks for key sizes and alignment went AWOL during the
skcipher conversion. This patch restores them.
Cc: <stable@vger.kernel.org>
Fixes: 4e6c3df4d7 ("crypto: skcipher - Add low-level skcipher...")
Reported-by: Baozeng <sploving1@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The DMA_PREP_FENCE is to be used when preparing Tx descriptor if output
of Tx descriptor is to be used by next/dependent Tx descriptor.
The DMA_PREP_FENSE will not be set correctly in do_async_gen_syndrome()
when calling dma->device_prep_dma_pq() under following conditions:
1. ASYNC_TX_FENCE not set in submit->flags
2. DMA_PREP_FENCE not set in dma_flags
3. src_cnt (= (disks - 2)) is greater than dma_maxpq(dma, dma_flags)
This patch fixes DMA_PREP_FENCE usage in do_async_gen_syndrome() taking
inspiration from do_async_xor() implementation.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There are many code paths opencoding kvmalloc. Let's use the helper
instead. The main difference to kvmalloc is that those users are
usually not considering all the aspects of the memory allocator. E.g.
allocation requests <= 32kB (with 4kB pages) are basically never failing
and invoke OOM killer to satisfy the allocation. This sounds too
disruptive for something that has a reasonable fallback - the vmalloc.
On the other hand those requests might fallback to vmalloc even when the
memory allocator would succeed after several more reclaim/compaction
attempts previously. There is no guarantee something like that happens
though.
This patch converts many of those places to kv[mz]alloc* helpers because
they are more conservative.
Link: http://lkml.kernel.org/r/20170306103327.2766-2-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> # Xen bits
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Andreas Dilger <andreas.dilger@intel.com> # Lustre
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com> # KVM/s390
Acked-by: Dan Williams <dan.j.williams@intel.com> # nvdim
Acked-by: David Sterba <dsterba@suse.com> # btrfs
Acked-by: Ilya Dryomov <idryomov@gmail.com> # Ceph
Acked-by: Tariq Toukan <tariqt@mellanox.com> # mlx4
Acked-by: Leon Romanovsky <leonro@mellanox.com> # mlx5
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Colin Cross <ccross@android.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Cc: Santosh Raspatur <santosh@chelsio.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Yishai Hadas <yishaih@mellanox.com>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: "Yan, Zheng" <zyan@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull security subsystem updates from James Morris:
"Highlights:
IMA:
- provide ">" and "<" operators for fowner/uid/euid rules
KEYS:
- add a system blacklist keyring
- add KEYCTL_RESTRICT_KEYRING, exposes keyring link restriction
functionality to userland via keyctl()
LSM:
- harden LSM API with __ro_after_init
- add prlmit security hook, implement for SELinux
- revive security_task_alloc hook
TPM:
- implement contextual TPM command 'spaces'"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (98 commits)
tpm: Fix reference count to main device
tpm_tis: convert to using locality callbacks
tpm: fix handling of the TPM 2.0 event logs
tpm_crb: remove a cruft constant
keys: select CONFIG_CRYPTO when selecting DH / KDF
apparmor: Make path_max parameter readonly
apparmor: fix parameters so that the permission test is bypassed at boot
apparmor: fix invalid reference to index variable of iterator line 836
apparmor: use SHASH_DESC_ON_STACK
security/apparmor/lsm.c: set debug messages
apparmor: fix boolreturn.cocci warnings
Smack: Use GFP_KERNEL for smk_netlbl_mls().
smack: fix double free in smack_parse_opts_str()
KEYS: add SP800-56A KDF support for DH
KEYS: Keyring asymmetric key restrict method with chaining
KEYS: Restrict asymmetric key linkage using a specific keychain
KEYS: Add a lookup_restriction function for the asymmetric key type
KEYS: Add KEYCTL_RESTRICT_KEYRING
KEYS: Consistent ordering for __key_link_begin and restrict check
KEYS: Add an optional lookup_restriction hook to key_type
...
Pull networking updates from David Millar:
"Here are some highlights from the 2065 networking commits that
happened this development cycle:
1) XDP support for IXGBE (John Fastabend) and thunderx (Sunil Kowuri)
2) Add a generic XDP driver, so that anyone can test XDP even if they
lack a networking device whose driver has explicit XDP support
(me).
3) Sparc64 now has an eBPF JIT too (me)
4) Add a BPF program testing framework via BPF_PROG_TEST_RUN (Alexei
Starovoitov)
5) Make netfitler network namespace teardown less expensive (Florian
Westphal)
6) Add symmetric hashing support to nft_hash (Laura Garcia Liebana)
7) Implement NAPI and GRO in netvsc driver (Stephen Hemminger)
8) Support TC flower offload statistics in mlxsw (Arkadi Sharshevsky)
9) Multiqueue support in stmmac driver (Joao Pinto)
10) Remove TCP timewait recycling, it never really could possibly work
well in the real world and timestamp randomization really zaps any
hint of usability this feature had (Soheil Hassas Yeganeh)
11) Support level3 vs level4 ECMP route hashing in ipv4 (Nikolay
Aleksandrov)
12) Add socket busy poll support to epoll (Sridhar Samudrala)
13) Netlink extended ACK support (Johannes Berg, Pablo Neira Ayuso,
and several others)
14) IPSEC hw offload infrastructure (Steffen Klassert)"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2065 commits)
tipc: refactor function tipc_sk_recv_stream()
tipc: refactor function tipc_sk_recvmsg()
net: thunderx: Optimize page recycling for XDP
net: thunderx: Support for XDP header adjustment
net: thunderx: Add support for XDP_TX
net: thunderx: Add support for XDP_DROP
net: thunderx: Add basic XDP support
net: thunderx: Cleanup receive buffer allocation
net: thunderx: Optimize CQE_TX handling
net: thunderx: Optimize RBDR descriptor handling
net: thunderx: Support for page recycling
ipx: call ipxitf_put() in ioctl error path
net: sched: add helpers to handle extended actions
qed*: Fix issues in the ptp filter config implementation.
qede: Fix concurrency issue in PTP Tx path processing.
stmmac: Add support for SIMATIC IOT2000 platform
net: hns: fix ethtool_get_strings overflow in hns driver
tcp: fix wraparound issue in tcp_lp
bpf, arm64: fix jit branch offset related to ldimm64
bpf, arm64: implement jiting of BPF_XADD
...
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 4.12:
API:
- Add batch registration for acomp/scomp
- Change acomp testing to non-unique compressed result
- Extend algorithm name limit to 128 bytes
- Require setkey before accept(2) in algif_aead
Algorithms:
- Add support for deflate rfc1950 (zlib)
Drivers:
- Add accelerated crct10dif for powerpc
- Add crc32 in stm32
- Add sha384/sha512 in ccp
- Add 3des/gcm(aes) for v5 devices in ccp
- Add Queue Interface (QI) backend support in caam
- Add new Exynos RNG driver
- Add ThunderX ZIP driver
- Add driver for hardware random generator on MT7623 SoC"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (101 commits)
crypto: stm32 - Fix OF module alias information
crypto: algif_aead - Require setkey before accept(2)
crypto: scomp - add support for deflate rfc1950 (zlib)
crypto: scomp - allow registration of multiple scomps
crypto: ccp - Change ISR handler method for a v5 CCP
crypto: ccp - Change ISR handler method for a v3 CCP
crypto: crypto4xx - rename ce_ring_contol to ce_ring_control
crypto: testmgr - Allow ecb(cipher_null) in FIPS mode
Revert "crypto: arm64/sha - Add constant operand modifier to ASM_EXPORT"
crypto: ccp - Disable interrupts early on unload
crypto: ccp - Use only the relevant interrupt bits
hwrng: mtk - Add driver for hardware random generator on MT7623 SoC
dt-bindings: hwrng: Add Mediatek hardware random generator bindings
crypto: crct10dif-vpmsum - Fix missing preempt_disable()
crypto: testmgr - replace compression known answer test
crypto: acomp - allow registration of multiple acomps
hwrng: n2 - Use devm_kcalloc() in n2rng_probe()
crypto: chcr - Fix error handling related to 'chcr_alloc_shash'
padata: get_next is never NULL
crypto: exynos - Add new Exynos RNG driver
...
Some cipher implementations will crash if you try to use them
without calling setkey first. This patch adds a check so that
the accept(2) call will fail with -ENOKEY if setkey hasn't been
done on the socket yet.
Fixes: 400c40cf78 ("crypto: algif - add AEAD support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add scomp backend for zlib-deflate compression algorithm.
This backend outputs data using the format defined in rfc1950
(raw deflate surrounded by zlib header and footer).
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add crypto_register_scomps and crypto_unregister_scomps to allow
the registration of multiple implementations with one call.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The cipher_null is not a real cipher, FIPS mode should not restrict its use.
It is used for several tests (for example in cryptsetup testsuite) and also
temporarily for reencryption of not yet encrypted device in cryptsetup-reencrypt tool.
Problem is easily reproducible with
cryptsetup benchmark -c null
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Acked-by: Stephan Müller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Compression implementations might return valid outputs that
do not match what specified in the test vectors.
For this reason, the testmgr might report that a compression
implementation failed the test even if the data produced
by the compressor is correct.
This implements a decompress-and-verify test for acomp
compression tests rather than a known answer test.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add crypto_register_acomps and crypto_unregister_acomps to allow
the registration of multiple implementations with one call.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
A function in kernel/bpf/syscall.c which got a bug fix in 'net'
was moved to kernel/bpf/verifier.c in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull crypto fixes from Herbert Xu:
"This fixes the following problems:
- regression in new XTS/LRW code when used with async crypto
- long-standing bug in ahash API when used with certain algos
- bogus memory dereference in async algif_aead with certain algos"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: algif_aead - Fix bogus request dereference in completion function
crypto: ahash - Fix EINPROGRESS notification callback
crypto: lrw - Fix use-after-free on EINPROGRESS
crypto: xts - Fix use-after-free on EINPROGRESS
Pass the new extended ACK reporting struct to all of the generic
netlink parsing functions. For now, pass NULL in almost all callers
(except for some in the core.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the base infrastructure and UAPI for netlink extended ACK
reporting. All "manual" calls to netlink_ack() pass NULL for now and
thus don't get extended ACK reporting.
Big thanks goes to Pablo Neira Ayuso for not only bringing up the
whole topic at netconf (again) but also coming up with the nlattr
passing trick and various other ideas.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Decompress function in LZ4 library is supposed to return an error code or
negative result. But, it returns -1 when any error is detected. Return
error code when the library returns negative value.
Signed-off-by: Myungho Jung <mhjungk@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch removes the hard-coded 64-byte limit on the length
of the algorithm name through bind(2). The address length can
now exceed that. The user-space structure remains unchanged.
In order to use a longer name simply extend the salg_name array
beyond its defined 64 bytes length.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch hard-codes CRYPTO_MAX_NAME in the user-space API to
64, which is the current value of CRYPTO_MAX_ALG_NAME. This patch
also replaces all remaining occurences of CRYPTO_MAX_ALG_NAME
in the user-space API with CRYPTO_MAX_NAME.
This way the user-space API will not be modified when we raise
the value of CRYPTO_MAX_ALG_NAME.
Furthermore, the code has been updated to handle names longer than
the user-space API. They will be truncated.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
The algif_aead completion function tries to deduce the aead_request
from the crypto_async_request argument. This is broken because
the API does not guarantee that the same request will be pased to
the completion function. Only the value of req->data can be used
in the completion function.
This patch fixes it by storing a pointer to sk in areq and using
that instead of passing in sk through req->data.
Fixes: 83094e5e9e ("crypto: af_alg - add async support to...")
Cc: <stable@vger.kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The ahash API modifies the request's callback function in order
to clean up after itself in some corner cases (unaligned final
and missing finup).
When the request is complete ahash will restore the original
callback and everything is fine. However, when the request gets
an EBUSY on a full queue, an EINPROGRESS callback is made while
the request is still ongoing.
In this case the ahash API will incorrectly call its own callback.
This patch fixes the problem by creating a temporary request
object on the stack which is used to relay EINPROGRESS back to
the original completion function.
This patch also adds code to preserve the original flags value.
Fixes: ab6bf4e5e5 ("crypto: hash - Fix the pointer voodoo in...")
Cc: <stable@vger.kernel.org>
Reported-by: Sabrina Dubroca <sd@queasysnail.net>
Tested-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When we get an EINPROGRESS completion in lrw, we will end up marking
the request as done and freeing it. This then blows up when the
request is really completed as we've already freed the memory.
Fixes: 700cb3f5fe ("crypto: lrw - Convert to skcipher")
Cc: <stable@vger.kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When we get an EINPROGRESS completion in xts, we will end up marking
the request as done and freeing it. This then blows up when the
request is really completed as we've already freed the memory.
Fixes: f1c131b454 ("crypto: xts - Convert to skcipher")
Cc: <stable@vger.kernel.org>
Reported-by: Nathan Royce <nroycea+kernel@gmail.com>
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Since the gf128mul_x_ble function used by xts.c is now defined inline
in the header file, the XTS module no longer depends on gf128mul.
Therefore, the 'select CRYPTO_GF128MUL' line can be safely removed.
Signed-off-by: Ondrej Mosnacek <omosnacek@gmail.com>
Reviewd-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently, gf128mul_x_ble works with pointers to be128, even though it
actually interprets the words as little-endian. Consequently, it uses
cpu_to_le64/le64_to_cpu on fields of type __be64, which is incorrect.
This patch fixes that by changing the function to accept pointers to
le128 and updating all users accordingly.
Signed-off-by: Ondrej Mosnacek <omosnacek@gmail.com>
Reviewd-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The gf128mul_x_ble function is currently defined in gf128mul.c, because
it depends on the gf128mul_table_be multiplication table.
However, since the function is very small and only uses two values from
the table, it is better for it to be defined as inline function in
gf128mul.h. That way, the function can be inlined by the compiler for
better performance.
For consistency, the other gf128mul_x_* functions are also moved to the
header file. In addition, the code is rewritten to be constant-time.
After this change, the speed of the generic 'xts(aes)' implementation
increased from ~225 MiB/s to ~235 MiB/s (measured using 'cryptsetup
benchmark -c aes-xts-plain64' on an Intel system with CRYPTO_AES_X86_64
and CRYPTO_AES_NI_INTEL disabled).
Signed-off-by: Ondrej Mosnacek <omosnacek@gmail.com>
Reviewd-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add a restrict_link_by_key_or_keyring_chain link restriction that
searches for signing keys in the destination keyring in addition to the
signing key or keyring designated when the destination keyring was
created. Userspace enables this behavior by including the "chain" option
in the keyring restriction:
keyctl(KEYCTL_RESTRICT_KEYRING, keyring, "asymmetric",
"key_or_keyring:<signing key>:chain");
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Adds restrict_link_by_signature_keyring(), which uses the restrict_key
member of the provided destination_keyring data structure as the
key or keyring to search for signing keys.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Look up asymmetric keyring restriction information using the key-type
lookup_restrict hook.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
The first argument to the restrict_link_func_t functions was a keyring
pointer. These functions are called by the key subsystem with this
argument set to the destination keyring, but restrict_link_by_signature
expects a pointer to the relevant trusted keyring.
Restrict functions may need something other than a single struct key
pointer to allow or reject key linkage, so the data used to make that
decision (such as the trust keyring) is moved to a new, fourth
argument. The first argument is now always the destination keyring.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
PKCS#7: Handle certificates that are blacklisted when verifying the chain
of trust on the signatures on a PKCS#7 message.
Signed-off-by: David Howells <dhowells@redhat.com>
Allow X.509 certs to be blacklisted based on their TBSCertificate hash.
This is convenient since we have to determine this anyway to be able to
check the signature on an X.509 certificate. This is also what UEFI uses
in its blacklist.
If a certificate built into the kernel is blacklisted, something like the
following might then be seen during boot:
X.509: Cert 123412341234c55c1dcc601ab8e172917706aa32fb5eaf826813547fdf02dd46 is blacklisted
Problem loading in-kernel X.509 certificate (-129)
where the hex string shown is the blacklisted hash.
Signed-off-by: David Howells <dhowells@redhat.com>
Pull crypto fixes from Herbert Xu:
"This fixes the following issues:
- memory corruption when kmalloc fails in xts/lrw
- mark some CCP DMA channels as private
- fix reordering race in padata
- regression in omap-rng DT description"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: xts,lrw - fix out-of-bounds write after kmalloc failure
crypto: ccp - Make some CCP DMA channels private
padata: avoid race in reordering
dt-bindings: rng: clocks property on omap_rng not always mandatory
An SGL to be initialized only once even when its buffers are written
to several times.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
3DES is missing the fips_allowed flag for CTR mode.
Signed-off-by: Marcelo Henrique Cerri <marcelo.cerri@canonical.com>
Acked-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The md5_transform function is no longer used any where in the tree,
except for the crypto api's actual implementation of md5, so we can drop
the function from lib and put it as a static function of the crypto
file, where it belongs. There should be no new users of md5_transform,
anyway, since there are more modern ways of doing what it once achieved.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
vpmsum implementations often don't kick in for short test vectors.
This is a simple test module that does a configurable number of
random tests, each up to 64kB and each with random offsets.
Both CRC-T10DIF and CRC32C are tested.
Cc: Anton Blanchard <anton@samba.org>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
T10DIF is a CRC16 used heavily in NVMe.
It turns out we can accelerate it with a CRC32 library and a few
little tricks.
Provide the accelerator based the refactored CRC32 code.
Cc: Anton Blanchard <anton@samba.org>
Thanks-to: Hong Bo Peng <penghb@cn.ibm.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In the generic XTS and LRW algorithms, for input data > 128 bytes, a
temporary buffer is allocated to hold the values to be XOR'ed with the
data before and after encryption or decryption. If the allocation
fails, the fixed-size buffer embedded in the request buffer is meant to
be used as a fallback --- resulting in more calls to the ECB algorithm,
but still producing the correct result. However, we weren't correctly
limiting subreq->cryptlen in this case, resulting in pre_crypt()
overrunning the embedded buffer. Fix this by setting subreq->cryptlen
correctly.
Fixes: f1c131b454 ("crypto: xts - Convert to skcipher")
Fixes: 700cb3f5fe ("crypto: lrw - Convert to skcipher")
Cc: stable@vger.kernel.org # v4.10+
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Lockdep issues a circular dependency warning when AFS issues an operation
through AF_RXRPC from a context in which the VFS/VM holds the mmap_sem.
The theory lockdep comes up with is as follows:
(1) If the pagefault handler decides it needs to read pages from AFS, it
calls AFS with mmap_sem held and AFS begins an AF_RXRPC call, but
creating a call requires the socket lock:
mmap_sem must be taken before sk_lock-AF_RXRPC
(2) afs_open_socket() opens an AF_RXRPC socket and binds it. rxrpc_bind()
binds the underlying UDP socket whilst holding its socket lock.
inet_bind() takes its own socket lock:
sk_lock-AF_RXRPC must be taken before sk_lock-AF_INET
(3) Reading from a TCP socket into a userspace buffer might cause a fault
and thus cause the kernel to take the mmap_sem, but the TCP socket is
locked whilst doing this:
sk_lock-AF_INET must be taken before mmap_sem
However, lockdep's theory is wrong in this instance because it deals only
with lock classes and not individual locks. The AF_INET lock in (2) isn't
really equivalent to the AF_INET lock in (3) as the former deals with a
socket entirely internal to the kernel that never sees userspace. This is
a limitation in the design of lockdep.
Fix the general case by:
(1) Double up all the locking keys used in sockets so that one set are
used if the socket is created by userspace and the other set is used
if the socket is created by the kernel.
(2) Store the kern parameter passed to sk_alloc() in a variable in the
sock struct (sk_kern_sock). This informs sock_lock_init(),
sock_init_data() and sk_clone_lock() as to the lock keys to be used.
Note that the child created by sk_clone_lock() inherits the parent's
kern setting.
(3) Add a 'kern' parameter to ->accept() that is analogous to the one
passed in to ->create() that distinguishes whether kernel_accept() or
sys_accept4() was the caller and can be passed to sk_alloc().
Note that a lot of accept functions merely dequeue an already
allocated socket. I haven't touched these as the new socket already
exists before we get the parameter.
Note also that there are a couple of places where I've made the accepted
socket unconditionally kernel-based:
irda_accept()
rds_rcp_accept_one()
tcp_accept_from_sock()
because they follow a sock_create_kern() and accept off of that.
Whilst creating this, I noticed that lustre and ocfs don't create sockets
through sock_create_kern() and thus they aren't marked as for-kernel,
though they appear to be internal. I wonder if these should do that so
that they use the new set of lock keys.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When requesting a fallback algorithm, we should propagate the
NEED_FALLBACK bit when search for the underlying algorithm.
This will prevents drivers from allocating unnecessary fallbacks that
are never called. For instance, currently the vmx-crypto driver will use
the following chain of calls when calling the fallback implementation:
p8_aes_ctr -> ctr(p8_aes) -> aes-generic
However p8_aes will always delegate its calls to aes-generic. With this
patch, p8_aes_ctr will be able to use ctr(aes-generic) directly as its
fallback. The same applies to aes_s390.
Signed-off-by: Marcelo Henrique Cerri <marcelo.cerri@canonical.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When requesting a fallback algorithm, we should propagate the
NEED_FALLBACK bit when search for the underlying algorithm.
This will prevents drivers from allocating unnecessary fallbacks that
are never called. For instance, currently the vmx-crypto driver will use
the following chain of calls when calling the fallback implementation:
p8_aes_cbc -> cbc(p8_aes) -> aes-generic
However p8_aes will always delegate its calls to aes-generic. With this
patch, p8_aes_cbc will be able to use cbc(aes-generic) directly as its
fallback. The same applies to aes_s390.
Signed-off-by: Marcelo Henrique Cerri <marcelo.cerri@canonical.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cryptographic test vectors should never be modified, so constify them to
enforce this at both compile-time and run-time. This moves a significant
amount of data from .data to .rodata when the crypto tests are enabled.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Constify the buffer passed to crypto_kpp_set_secret() and
kpp_alg.set_secret, since it is never modified.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
To prevent unnecessary branching, mark the exit condition of the
primary loop as likely(), given that a carry in a 32-bit counter
occurs very rarely.
On arm64, the resulting code is emitted by GCC as
9a8: cmp w1, #0x3
9ac: add x3, x0, w1, uxtw
9b0: b.ls 9e0 <crypto_inc+0x38>
9b4: ldr w2, [x3,#-4]!
9b8: rev w2, w2
9bc: add w2, w2, #0x1
9c0: rev w4, w2
9c4: str w4, [x3]
9c8: cbz w2, 9d0 <crypto_inc+0x28>
9cc: ret
where the two remaining branch conditions (one for size < 4 and one for
the carry) are statically predicted as non-taken, resulting in optimal
execution in the vast majority of cases.
Also, replace the open coded alignment test with IS_ALIGNED().
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Constify the multiplication tables passed to the 4k and 64k
multiplication functions, as they are not modified by these functions.
Cc: Alex Cope <alexcope@google.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Though the GF(2^128) byte overflow tables were named the "lle" and "bbe"
tables, they are not actually tied to these element formats
specifically, but rather to particular a "bit endianness". For example,
the bbe table is actually used for both bbe and ble multiplication.
Therefore, rename the tables to "le" and "be" and update the comment to
explain this.
Cc: Alex Cope <alexcope@google.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The xx() macro serves no purpose and can be removed.
Cc: Alex Cope <alexcope@google.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix incorrect references to GF(128) instead of GF(2^128), as these are
two entirely different fields, and fix a few other incorrect comments.
Cc: Alex Cope <alexcope@google.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull crypto fixes from Herbert Xu:
- vmalloc stack regression in CCM
- Build problem in CRC32 on ARM
- Memory leak in cavium
- Missing Kconfig dependencies in atmel and mediatek
- XTS Regression on some platforms (s390 and ppc)
- Memory overrun in CCM test vector
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: vmx - Use skcipher for xts fallback
crypto: vmx - Use skcipher for cbc fallback
crypto: testmgr - Pad aes_ccm_enc_tv_template vector
crypto: arm/crc32 - add build time test for CRC instruction support
crypto: arm/crc32 - fix build error with outdated binutils
crypto: ccm - move cbcmac input off the stack
crypto: xts - Propagate NEED_FALLBACK bit
crypto: api - Add crypto_requires_off helper
crypto: atmel - CRYPTO_DEV_MEDIATEK should depend on HAS_DMA
crypto: atmel - CRYPTO_DEV_ATMEL_TDES and CRYPTO_DEV_ATMEL_SHA should depend on HAS_DMA
crypto: cavium - fix leak on curr if curr->head fails to be allocated
crypto: cavium - Fix couple of static checker errors
We are going to split <linux/sched/stat.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/stat.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to move scheduler ABI details to <uapi/linux/sched/types.h>,
which will be used from a number of .c files.
Create empty placeholder header that maps to <linux/types.h>.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Running with KASAN and crypto tests currently gives
BUG: KASAN: global-out-of-bounds in __test_aead+0x9d9/0x2200 at addr ffffffff8212fca0
Read of size 16 by task cryptomgr_test/1107
Address belongs to variable 0xffffffff8212fca0
CPU: 0 PID: 1107 Comm: cryptomgr_test Not tainted 4.10.0+ #45
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.9.1-1.fc24 04/01/2014
Call Trace:
dump_stack+0x63/0x8a
kasan_report.part.1+0x4a7/0x4e0
? __test_aead+0x9d9/0x2200
? crypto_ccm_init_crypt+0x218/0x3c0 [ccm]
kasan_report+0x20/0x30
check_memory_region+0x13c/0x1a0
memcpy+0x23/0x50
__test_aead+0x9d9/0x2200
? kasan_unpoison_shadow+0x35/0x50
? alg_test_akcipher+0xf0/0xf0
? crypto_skcipher_init_tfm+0x2e3/0x310
? crypto_spawn_tfm2+0x37/0x60
? crypto_ccm_init_tfm+0xa9/0xd0 [ccm]
? crypto_aead_init_tfm+0x7b/0x90
? crypto_alloc_tfm+0xc4/0x190
test_aead+0x28/0xc0
alg_test_aead+0x54/0xd0
alg_test+0x1eb/0x3d0
? alg_find_test+0x90/0x90
? __sched_text_start+0x8/0x8
? __wake_up_common+0x70/0xb0
cryptomgr_test+0x4d/0x60
kthread+0x173/0x1c0
? crypto_acomp_scomp_free_ctx+0x60/0x60
? kthread_create_on_node+0xa0/0xa0
ret_from_fork+0x2c/0x40
Memory state around the buggy address:
ffffffff8212fb80: 00 00 00 00 01 fa fa fa fa fa fa fa 00 00 00 00
ffffffff8212fc00: 00 01 fa fa fa fa fa fa 00 00 00 00 01 fa fa fa
>ffffffff8212fc80: fa fa fa fa 00 05 fa fa fa fa fa fa 00 00 00 00
^
ffffffff8212fd00: 01 fa fa fa fa fa fa fa 00 00 00 00 01 fa fa fa
ffffffff8212fd80: fa fa fa fa 00 00 00 00 00 05 fa fa fa fa fa fa
This always happens on the same IV which is less than 16 bytes.
Per Ard,
"CCM IVs are 16 bytes, but due to the way they are constructed
internally, the final couple of bytes of input IV are dont-cares.
Apparently, we do read all 16 bytes, which triggers the KASAN errors."
Fix this by padding the IV with null bytes to be at least 16 bytes.
Cc: stable@vger.kernel.org
Fixes: 0bc5a6c5c7 ("crypto: testmgr - Disable rfc4309 test and convert
test vectors")
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Commit f15f05b0a5 ("crypto: ccm - switch to separate cbcmac driver")
refactored the CCM driver to allow separate implementations of the
underlying MAC to be provided by a platform. However, in doing so, it
moved some data from the linear region to the stack, which violates the
SG constraints when the stack is virtually mapped.
So move idata/odata back to the request ctx struct, of which we can
reasonably expect that it has been allocated using kmalloc() et al.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Fixes: f15f05b0a5 ("crypto: ccm - switch to separate cbcmac driver")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When we're used as a fallback algorithm, we should propagate
the NEED_FALLBACK bit when searching for the underlying ECB mode.
This just happens to fix a hang too because otherwise the search
may end up loading the same module that triggered this XTS creation.
Cc: stable@vger.kernel.org #4.10
Fixes: f1c131b454 ("crypto: xts - Convert to skcipher")
Reported-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Update the crypto modules using LZ4 compression as well as the test
cases in testmgr.h to work with the new LZ4 module version.
Link: http://lkml.kernel.org/r/1486321748-19085-4-git-send-email-4sschmid@informatik.uni-hamburg.de
Signed-off-by: Sven Schmidt <4sschmid@informatik.uni-hamburg.de>
Cc: Bongkyu Kim <bongkyu.kim@lge.com>
Cc: Rui Salvaterra <rsalvaterra@gmail.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David S. Miller <davem@davemloft.net>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Colin Cross <ccross@android.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since the
commit f1c131b454
crypto: xts - Convert to skcipher
the XTS mode is based on ECB, so the mode must select
ECB otherwise it can fail to initialize.
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The CCM driver forces 32-bit alignment even if the underlying ciphers
don't care about alignment. This is because crypto_xor() used to require
this, but since this is no longer the case, drop the hardcoded minimum
of 32 bits.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The CCM driver was recently updated to defer the MAC part of the algorithm
to a dedicated crypto transform, and a template for instantiating such
transforms was added at the same time.
However, this new cbcmac template fails to take the alignmask of the
encapsulated cipher into account, which may result in buffer addresses
being passed down that are not sufficiently aligned.
So update the code to ensure that the digest buffer in the desc ctx
appears at a sufficiently aligned offset, and tweak the code so that all
calls to crypto_cipher_encrypt_one() operate on this buffer exclusively.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Instead of unconditionally forcing 4 byte alignment for all generic
chaining modes that rely on crypto_xor() or crypto_inc() (which may
result in unnecessary copying of data when the underlying hardware
can perform unaligned accesses efficiently), make those functions
deal with unaligned input explicitly, but only if the Kconfig symbol
HAVE_EFFICIENT_UNALIGNED_ACCESS is set. This will allow us to drop
the alignmasks from the CBC, CMAC, CTR, CTS, PCBC and SEQIV drivers.
For crypto_inc(), this simply involves making the 4-byte stride
conditional on HAVE_EFFICIENT_UNALIGNED_ACCESS being set, given that
it typically operates on 16 byte buffers.
For crypto_xor(), an algorithm is implemented that simply runs through
the input using the largest strides possible if unaligned accesses are
allowed. If they are not, an optimal sequence of memory accesses is
emitted that takes the relative alignment of the input buffers into
account, e.g., if the relative misalignment of dst and src is 4 bytes,
the entire xor operation will be completed using 4 byte loads and stores
(modulo unaligned bits at the start and end). Note that all expressions
involving misalign are simply eliminated by the compiler when
HAVE_EFFICIENT_UNALIGNED_ACCESS is defined.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
An ancient gcc bug (first reported in 2003) has apparently resurfaced
on MIPS, where kernelci.org reports an overly large stack frame in the
whirlpool hash algorithm:
crypto/wp512.c:987:1: warning: the frame size of 1112 bytes is larger than 1024 bytes [-Wframe-larger-than=]
With some testing in different configurations, I'm seeing large
variations in stack frames size up to 1500 bytes for what should have
around 300 bytes at most. I also checked the reference implementation,
which is essentially the same code but also comes with some test and
benchmarking infrastructure.
It seems that recent compiler versions on at least arm, arm64 and powerpc
have a partial fix for this problem, but enabling "-fsched-pressure", but
even with that fix they suffer from the issue to a certain degree. Some
testing on arm64 shows that the time needed to hash a given amount of
data is roughly proportional to the stack frame size here, which makes
sense given that the wp512 implementation is doing lots of loads for
table lookups, and the problem with the overly large stack is a result
of doing a lot more loads and stores for spilled registers (as seen from
inspecting the object code).
Disabling -fschedule-insns consistently fixes the problem for wp512,
in my collection of cross-compilers, the results are consistently better
or identical when comparing the stack sizes in this function, though
some architectures (notable x86) have schedule-insns disabled by
default.
The four columns are:
default: -O2
press: -O2 -fsched-pressure
nopress: -O2 -fschedule-insns -fno-sched-pressure
nosched: -O2 -no-schedule-insns (disables sched-pressure)
default press nopress nosched
alpha-linux-gcc-4.9.3 1136 848 1136 176
am33_2.0-linux-gcc-4.9.3 2100 2076 2100 2104
arm-linux-gnueabi-gcc-4.9.3 848 848 1048 352
cris-linux-gcc-4.9.3 272 272 272 272
frv-linux-gcc-4.9.3 1128 1000 1128 280
hppa64-linux-gcc-4.9.3 1128 336 1128 184
hppa-linux-gcc-4.9.3 644 308 644 276
i386-linux-gcc-4.9.3 352 352 352 352
m32r-linux-gcc-4.9.3 720 656 720 268
microblaze-linux-gcc-4.9.3 1108 604 1108 256
mips64-linux-gcc-4.9.3 1328 592 1328 208
mips-linux-gcc-4.9.3 1096 624 1096 240
powerpc64-linux-gcc-4.9.3 1088 432 1088 160
powerpc-linux-gcc-4.9.3 1080 584 1080 224
s390-linux-gcc-4.9.3 456 456 624 360
sh3-linux-gcc-4.9.3 292 292 292 292
sparc64-linux-gcc-4.9.3 992 240 992 208
sparc-linux-gcc-4.9.3 680 592 680 312
x86_64-linux-gcc-4.9.3 224 240 272 224
xtensa-linux-gcc-4.9.3 1152 704 1152 304
aarch64-linux-gcc-7.0.0 224 224 1104 208
arm-linux-gnueabi-gcc-7.0.1 824 824 1048 352
mips-linux-gcc-7.0.0 1120 648 1120 272
x86_64-linux-gcc-7.0.1 240 240 304 240
arm-linux-gnueabi-gcc-4.4.7 840 392
arm-linux-gnueabi-gcc-4.5.4 784 728 784 320
arm-linux-gnueabi-gcc-4.6.4 736 728 736 304
arm-linux-gnueabi-gcc-4.7.4 944 784 944 352
arm-linux-gnueabi-gcc-4.8.5 464 464 760 352
arm-linux-gnueabi-gcc-4.9.3 848 848 1048 352
arm-linux-gnueabi-gcc-5.3.1 824 824 1064 336
arm-linux-gnueabi-gcc-6.1.1 808 808 1056 344
arm-linux-gnueabi-gcc-7.0.1 824 824 1048 352
Trying the same test for serpent-generic, the picture is a bit different,
and while -fno-schedule-insns is generally better here than the default,
-fsched-pressure wins overall, so I picked that instead.
default press nopress nosched
alpha-linux-gcc-4.9.3 1392 864 1392 960
am33_2.0-linux-gcc-4.9.3 536 524 536 528
arm-linux-gnueabi-gcc-4.9.3 552 552 776 536
cris-linux-gcc-4.9.3 528 528 528 528
frv-linux-gcc-4.9.3 536 400 536 504
hppa64-linux-gcc-4.9.3 524 208 524 480
hppa-linux-gcc-4.9.3 768 472 768 508
i386-linux-gcc-4.9.3 564 564 564 564
m32r-linux-gcc-4.9.3 712 576 712 532
microblaze-linux-gcc-4.9.3 724 392 724 512
mips64-linux-gcc-4.9.3 720 384 720 496
mips-linux-gcc-4.9.3 728 384 728 496
powerpc64-linux-gcc-4.9.3 704 304 704 480
powerpc-linux-gcc-4.9.3 704 296 704 480
s390-linux-gcc-4.9.3 560 560 592 536
sh3-linux-gcc-4.9.3 540 540 540 540
sparc64-linux-gcc-4.9.3 544 352 544 496
sparc-linux-gcc-4.9.3 544 344 544 496
x86_64-linux-gcc-4.9.3 528 536 576 528
xtensa-linux-gcc-4.9.3 752 544 752 544
aarch64-linux-gcc-7.0.0 432 432 656 480
arm-linux-gnueabi-gcc-7.0.1 616 616 808 536
mips-linux-gcc-7.0.0 720 464 720 488
x86_64-linux-gcc-7.0.1 536 528 600 536
arm-linux-gnueabi-gcc-4.4.7 592 440
arm-linux-gnueabi-gcc-4.5.4 776 448 776 544
arm-linux-gnueabi-gcc-4.6.4 776 448 776 544
arm-linux-gnueabi-gcc-4.7.4 768 448 768 544
arm-linux-gnueabi-gcc-4.8.5 488 488 776 544
arm-linux-gnueabi-gcc-4.9.3 552 552 776 536
arm-linux-gnueabi-gcc-5.3.1 552 552 776 536
arm-linux-gnueabi-gcc-6.1.1 560 560 776 536
arm-linux-gnueabi-gcc-7.0.1 616 616 808 536
I did not do any runtime tests with serpent, so it is possible that stack
frame size does not directly correlate with runtime performance here and
it actually makes things worse, but it's more likely to help here, and
the reduced stack frame size is probably enough reason to apply the patch,
especially given that the crypto code is often used in deep call chains.
Link: https://kernelci.org/build/id/58797d7559b5149efdf6c3a9/logs/
Link: http://www.larc.usp.br/~pbarreto/WhirlpoolPage.html
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=11488
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=79149
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Update the generic CCM driver to defer CBC-MAC processing to a
dedicated CBC-MAC ahash transform rather than open coding this
transform (and much of the associated scatterwalk plumbing) in
the CCM driver itself.
This cleans up the code considerably, but more importantly, it allows
the use of alternative CBC-MAC implementations that don't suffer from
performance degradation due to significant setup time (e.g., the NEON
based AES code needs to enable/disable the NEON, and load the S-box
into 16 SIMD registers, which cannot be amortized over the entire input
when using the cipher interface)
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In preparation of splitting off the CBC-MAC transform in the CCM
driver into a separate algorithm, define some test cases for the
AES incarnation of cbcmac.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Lookup table based AES is sensitive to timing attacks, which is due to
the fact that such table lookups are data dependent, and the fact that
8 KB worth of tables covers a significant number of cachelines on any
architecture, resulting in an exploitable correlation between the key
and the processing time for known plaintexts.
For network facing algorithms such as CTR, CCM or GCM, this presents a
security risk, which is why arch specific AES ports are typically time
invariant, either through the use of special instructions, or by using
SIMD algorithms that don't rely on table lookups.
For generic code, this is difficult to achieve without losing too much
performance, but we can improve the situation significantly by switching
to an implementation that only needs 256 bytes of table data (the actual
S-box itself), which can be prefetched at the start of each block to
eliminate data dependent latencies.
This code encrypts at ~25 cycles per byte on ARM Cortex-A57 (while the
ordinary generic AES driver manages 18 cycles per byte on this
hardware). Decryption is substantially slower.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The generic AES code exposes a 32-bit align mask, which forces all
users of the code to use temporary buffers or take other measures to
ensure the alignment requirement is adhered to, even on architectures
that don't care about alignment for software algorithms such as this
one.
So drop the align mask, and fix the code to use get_unaligned_le32()
where appropriate, which will resolve to whatever is optimal for the
architecture.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Kernel panics when userspace program try to access AEAD interface.
Remove node from Linked List before freeing its memory.
Cc: <stable@vger.kernel.org>
Signed-off-by: Harsh Jain <harsh@chelsio.com>
Reviewed-by: Stephan Müller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
tcrypt is very tight-lipped when it succeeds, but a bit more feedback
would be useful when developing or debugging crypto drivers, especially
since even a successful run ends with the module failing to insert. Add
a couple of debug prints, which can be enabled with dynamic debug:
Before:
# insmod tcrypt.ko mode=10
insmod: can't insert 'tcrypt.ko': Resource temporarily unavailable
After:
# insmod tcrypt.ko mode=10 dyndbg
tcrypt: testing ecb(aes)
tcrypt: testing cbc(aes)
tcrypt: testing lrw(aes)
tcrypt: testing xts(aes)
tcrypt: testing ctr(aes)
tcrypt: testing rfc3686(ctr(aes))
tcrypt: all tests passed
insmod: can't insert 'tcrypt.ko': Resource temporarily unavailable
Signed-off-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Make sure CRYPTO_ALG_DEAD bit is cleared before proceeding with
the algorithm registration. This fixes qat-dh registration when
driver is restarted
Cc: <stable@vger.kernel.org>
Signed-off-by: Salvatore Benedetto <salvatore.benedetto@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When working on AES in CCM mode for ARM, my code passed the internal
tcrypt test before I had even bothered to implement the AES-192 and
AES-256 code paths, which is strange because the tcrypt does contain
AES-192 and AES-256 test vectors for CCM.
As it turned out, the define AES_CCM_ENC_TEST_VECTORS was out of sync
with the actual number of test vectors, causing only the AES-128 ones
to be executed.
So get rid of the defines, and wrap the test vector references in a
macro that calculates the number of vectors automatically.
The following test vector counts were out of sync with the respective
defines:
BF_CTR_ENC_TEST_VECTORS 2 -> 3
BF_CTR_DEC_TEST_VECTORS 2 -> 3
TF_CTR_ENC_TEST_VECTORS 2 -> 3
TF_CTR_DEC_TEST_VECTORS 2 -> 3
SERPENT_CTR_ENC_TEST_VECTORS 2 -> 3
SERPENT_CTR_DEC_TEST_VECTORS 2 -> 3
AES_CCM_ENC_TEST_VECTORS 8 -> 14
AES_CCM_DEC_TEST_VECTORS 7 -> 17
AES_CCM_4309_ENC_TEST_VECTORS 7 -> 23
AES_CCM_4309_DEC_TEST_VECTORS 10 -> 23
CAMELLIA_CTR_ENC_TEST_VECTORS 2 -> 3
CAMELLIA_CTR_DEC_TEST_VECTORS 2 -> 3
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There are some hashes (e.g. sha224) that have some internal trickery
to make sure that only the correct number of output bytes are
generated. If something goes wrong, they could potentially overrun
the output buffer.
Make the test more robust by allocating only enough space for the
correct output size so that memory debugging will catch the error if
the output is overrun.
Tested by intentionally breaking sha224 to output all 256
internally-generated bits while running on KASAN.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Continuing from this commit: 52f5684c8e
("kernel: use macros from compiler.h instead of __attribute__((...))")
I submitted 4 total patches. They are part of task I've taken up to
increase compiler portability in the kernel. I've cleaned up the
subsystems under /kernel /mm /block and /security, this patch targets
/crypto.
There is <linux/compiler.h> which provides macros for various gcc specific
constructs. Eg: __weak for __attribute__((weak)). I've cleaned all
instances of gcc specific attributes with the right macros for the crypto
subsystem.
I had to make one additional change into compiler-gcc.h for the case when
one wants to use this: __attribute__((aligned) and not specify an alignment
factor. From the gcc docs, this will result in the largest alignment for
that data type on the target machine so I've named the macro
__aligned_largest. Please advise if another name is more appropriate.
Signed-off-by: Gideon Israel Dsouza <gidisrael@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
It's recommended to use kmemdup instead of kmalloc followed by memcpy.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In some cases, SIMD algorithms can only perform optimally when
allowed to operate on multiple input blocks in parallel. This is
especially true for bit slicing algorithms, which typically take
the same amount of time processing a single block or 8 blocks in
parallel. However, other SIMD algorithms may benefit as well from
bigger strides.
So add a walksize attribute to the skcipher algorithm definition, and
wire it up to the skcipher walk API. To avoid confusion between the
skcipher and AEAD attributes, rename the skcipher_walk chunksize
attribute to 'stride', and set it from the walksize (in the skcipher
case) or from the chunksize (in the AEAD case).
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
With this reproducer:
struct sockaddr_alg alg = {
.salg_family = 0x26,
.salg_type = "hash",
.salg_feat = 0xf,
.salg_mask = 0x5,
.salg_name = "digest_null",
};
int sock, sock2;
sock = socket(AF_ALG, SOCK_SEQPACKET, 0);
bind(sock, (struct sockaddr *)&alg, sizeof(alg));
sock2 = accept(sock, NULL, NULL);
setsockopt(sock, SOL_ALG, ALG_SET_KEY, "\x9b\xca", 2);
accept(sock2, NULL, NULL);
==== 8< ======== 8< ======== 8< ======== 8< ====
one can immediatelly see an UBSAN warning:
UBSAN: Undefined behaviour in crypto/algif_hash.c:187:7
variable length array bound value 0 <= 0
CPU: 0 PID: 15949 Comm: syz-executor Tainted: G E 4.4.30-0-default #1
...
Call Trace:
...
[<ffffffff81d598fd>] ? __ubsan_handle_vla_bound_not_positive+0x13d/0x188
[<ffffffff81d597c0>] ? __ubsan_handle_out_of_bounds+0x1bc/0x1bc
[<ffffffffa0e2204d>] ? hash_accept+0x5bd/0x7d0 [algif_hash]
[<ffffffffa0e2293f>] ? hash_accept_nokey+0x3f/0x51 [algif_hash]
[<ffffffffa0e206b0>] ? hash_accept_parent_nokey+0x4a0/0x4a0 [algif_hash]
[<ffffffff8235c42b>] ? SyS_accept+0x2b/0x40
It is a correct warning, as hash state is propagated to accept as zero,
but creating a zero-length variable array is not allowed in C.
Fix this as proposed by Herbert -- do "?: 1" on that site. No sizeof or
similar happens in the code there, so we just allocate one byte even
though we do not use the array.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net> (maintainer:CRYPTO API)
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This converts the ChaCha20 code from a blkcipher to a skcipher, which
is now the preferred way to implement symmetric block and stream ciphers.
This ports the generic and x86 versions at the same time because the
latter reuses routines of the former.
Note that the skcipher_walk() API guarantees that all presented blocks
except the final one are a multiple of the chunk size, so we can simplify
the encrypt() routine somewhat.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Christopher Covington reported a crash on aarch64 on recent Fedora
kernels:
kernel BUG at ./include/linux/scatterlist.h:140!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
Modules linked in:
CPU: 2 PID: 752 Comm: cryptomgr_test Not tainted 4.9.0-11815-ge93b1cc #162
Hardware name: linux,dummy-virt (DT)
task: ffff80007c650080 task.stack: ffff800008910000
PC is at sg_init_one+0xa0/0xb8
LR is at sg_init_one+0x24/0xb8
...
[<ffff000008398db8>] sg_init_one+0xa0/0xb8
[<ffff000008350a44>] test_acomp+0x10c/0x438
[<ffff000008350e20>] alg_test_comp+0xb0/0x118
[<ffff00000834f28c>] alg_test+0x17c/0x2f0
[<ffff00000834c6a4>] cryptomgr_test+0x44/0x50
[<ffff0000080dac70>] kthread+0xf8/0x128
[<ffff000008082ec0>] ret_from_fork+0x10/0x50
The test vectors used for input are part of the kernel image. These
inputs are passed as a buffer to sg_init_one which eventually blows up
with BUG_ON(!virt_addr_valid(buf)). On arm64, virt_addr_valid returns
false for the kernel image since virt_to_page will not return the
correct page. Fix this by copying the input vectors to heap buffer
before setting up the scatterlist.
Reported-by: Christopher Covington <cov@codeaurora.org>
Fixes: d7db7a882d ("crypto: acomp - update testmgr with support for acomp")
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull crypto fixes from Herbert Xu:
"This fixes the following issues:
- a crash regression in the new skcipher walker
- incorrect return value in public_key_verify_signature
- fix for in-place signing in the sign-file utility"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: skcipher - fix crash in virtual walk
sign-file: Fix inplace signing when src and dst names are both specified
crypto: asymmetric_keys - set error code on failure
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 4.10:
API:
- add skcipher walk interface
- add asynchronous compression (acomp) interface
- fix algif_aed AIO handling of zero buffer
Algorithms:
- fix unaligned access in poly1305
- fix DRBG output to large buffers
Drivers:
- add support for iMX6UL to caam
- fix givenc descriptors (used by IPsec) in caam
- accelerated SHA256/SHA512 for ARM64 from OpenSSL
- add SSE CRCT10DIF and CRC32 to ARM/ARM64
- add AEAD support to Chelsio chcr
- add Armada 8K support to omap-rng"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (148 commits)
crypto: testmgr - fix overlap in chunked tests again
crypto: arm/crc32 - accelerated support based on x86 SSE implementation
crypto: arm64/crc32 - accelerated support based on x86 SSE implementation
crypto: arm/crct10dif - port x86 SSE implementation to ARM
crypto: arm64/crct10dif - port x86 SSE implementation to arm64
crypto: testmgr - add/enhance test cases for CRC-T10DIF
crypto: testmgr - avoid overlap in chunked tests
crypto: chcr - checking for IS_ERR() instead of NULL
crypto: caam - check caam_emi_slow instead of re-lookup platform
crypto: algif_aead - fix AIO handling of zero buffer
crypto: aes-ce - Make aes_simd_algs static
crypto: algif_skcipher - set error code when kcalloc fails
crypto: caam - make aamalg_desc a proper module
crypto: caam - pass key buffers with typesafe pointers
crypto: arm64/aes-ce-ccm - Fix AEAD decryption length
MAINTAINERS: add crypto headers to crypto entry
crypt: doc - remove misleading mention of async API
crypto: doc - fix header file name
crypto: api - fix comment typo
crypto: skcipher - Add separate walker for AEAD decryption
..
The new skcipher walk API may crash in the following way. (Interestingly,
the tcrypt boot time tests seem unaffected, while an explicit test using
the module triggers it)
Unable to handle kernel NULL pointer dereference at virtual address 00000000
...
[<ffff000008431d84>] __memcpy+0x84/0x180
[<ffff0000083ec0d0>] skcipher_walk_done+0x328/0x340
[<ffff0000080c5c04>] ctr_encrypt+0x84/0x100
[<ffff000008406d60>] simd_skcipher_encrypt+0x88/0x98
[<ffff0000083fa05c>] crypto_rfc3686_crypt+0x8c/0x98
[<ffff0000009b0900>] test_skcipher_speed+0x518/0x820 [tcrypt]
[<ffff0000009b31c0>] do_test+0x1408/0x3b70 [tcrypt]
[<ffff0000009bd050>] tcrypt_mod_init+0x50/0x1000 [tcrypt]
[<ffff0000080838f4>] do_one_initcall+0x44/0x138
[<ffff0000081aee60>] do_init_module+0x68/0x1e0
[<ffff0000081524d0>] load_module+0x1fd0/0x2458
[<ffff000008152c38>] SyS_finit_module+0xe0/0xf0
[<ffff0000080836f0>] el0_svc_naked+0x24/0x28
This is due to the fact that skcipher_done_slow() may be entered with
walk->buffer unset. Since skcipher_walk_done() already deals with the
case where walk->buffer == walk->page, it appears to be the intention
that walk->buffer point to walk->page after skcipher_next_slow(), so
ensure that is the case.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In function public_key_verify_signature(), returns variable ret on
error paths. When the call to kmalloc() fails, the value of ret is 0,
and it is not set to an errno before returning. This patch fixes the
bug.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188891
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The previous description have been misleading and partially incorrect.
Reported-by: Harsh Jain <harshjain.prof@gmail.com>
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Pull crypto fixes from Herbert Xu:
"This fixes the following issues:
- Fix pointer size when caam is used with AArch64 boot loader on
AArch32 kernel.
- Fix ahash state corruption in marvell driver.
- Fix buggy algif_aed tag handling.
- Prevent mcryptd from being used with incompatible algorithms which
can cause crashes"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: algif_aead - fix uninitialized variable warning
crypto: mcryptd - Check mcryptd algorithm compatibility
crypto: algif_aead - fix AEAD tag memory handling
crypto: caam - fix pointer size for AArch64 boot loader, AArch32 kernel
crypto: marvell - Don't corrupt state of an STD req for re-stepped ahash
crypto: marvell - Don't copy hash operation twice into the SRAM
Commit 7e4c7f17cd ("crypto: testmgr - avoid overlap in chunked tests")
attempted to address a problem in the crypto testmgr code where chunked
test cases are copied to memory in a way that results in overlap.
However, the fix recreated the exact same issue for other chunked tests,
by putting IDX3 within 492 bytes of IDX1, which causes overlap if the
first chunk exceeds 492 bytes, which is the case for at least one of
the xts(aes) test cases.
So increase IDX3 by another 1000 bytes.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In case the user provided insufficient data, the code may return
prematurely without any operation. In this case, the processed
data indicated with outlen is zero.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The existing test cases only exercise a small slice of the various
possible code paths through the x86 SSE/PCLMULQDQ implementation,
and the upcoming ports of it for arm64. So add one that exceeds 256
bytes in size, and convert another to a chunked test.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The IDXn offsets are chosen such that tap values (which may go up to
255) end up overlapping in the xbuf allocation. In particular, IDX1
and IDX3 are too close together, so update IDX3 to avoid this issue.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Algorithms not compatible with mcryptd could be spawned by mcryptd
with a direct crypto_alloc_tfm invocation using a "mcryptd(alg)" name
construct. This causes mcryptd to crash the kernel if an arbitrary
"alg" is incompatible and not intended to be used with mcryptd. It is
an issue if AF_ALG tries to spawn mcryptd(alg) to expose it externally.
But such algorithms must be used internally and not be exposed.
We added a check to enforce that only internal algorithms are allowed
with mcryptd at the time mcryptd is spawning an algorithm.
Link: http://marc.info/?l=linux-crypto-vger&m=148063683310477&w=2
Cc: stable@vger.kernel.org
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For encryption, the AEAD ciphers require AAD || PT as input and generate
AAD || CT || Tag as output and vice versa for decryption. Prior to this
patch, the AF_ALG interface for AEAD ciphers requires the buffer to be
present as input for encryption. Similarly, the output buffer for
decryption required the presence of the tag buffer too. This implies
that the kernel reads / writes data buffers from/to kernel space
even though this operation is not required.
This patch changes the AF_ALG AEAD interface to be consistent with the
in-kernel AEAD cipher requirements.
Due to this handling, he changes are transparent to user space with one
exception: the return code of recv indicates the mount of output buffer.
That output buffer has a different size compared to before the patch
which implies that the return code of recv will also be different.
For example, a decryption operation uses 16 bytes AAD, 16 bytes CT and
16 bytes tag, the AF_ALG AEAD interface before showed a recv return
code of 48 (bytes) whereas after this patch, the return code is 32
since the tag is not returned any more.
Reported-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Handle the case when the caller provided a zero buffer to
sendmsg/sendpage. Such scenario is legal for AEAD ciphers when no
plaintext / ciphertext and no AAD is provided and the caller only
requests the generation of the tag value.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix bug https://bugzilla.kernel.org/show_bug.cgi?id=188521. In function
skcipher_recvmsg_async(), variable err takes the return value, and its
value should be negative on failures. Because variable err may be
reassigned and checked before calling kcalloc(), its value may be 0
(indicates no error) even if kcalloc() fails. This patch fixes the bug
by explicitly assigning -ENOMEM to err when kcalloc() returns a NULL
pointer.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The AEAD decrypt interface includes the authentication tag in
req->cryptlen. Therefore we need to exlucde that when doing
a walk over it.
This patch adds separate walker functions for AEAD encryption
and decryption.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
The new skcipher_walk_aead() may crash in the following way due to
the walk flag SKCIPHER_WALK_PHYS not being cleared at the start of the
walk:
Unable to handle kernel NULL pointer dereference at virtual address 00000001
[..]
Internal error: Oops: 96000044 [#1] PREEMPT SMP
[..]
PC is at skcipher_walk_next+0x208/0x450
LR is at skcipher_walk_next+0x1e4/0x450
pc : [<ffff2b93b7104e20>] lr : [<ffff2b93b7104dfc>] pstate: 40000045
sp : ffffb925fa517940
[...]
[<ffff2b93b7104e20>] skcipher_walk_next+0x208/0x450
[<ffff2b93b710535c>] skcipher_walk_first+0x54/0x148
[<ffff2b93b7105664>] skcipher_walk_aead+0xd4/0x108
[<ffff2b93b6e77928>] ccm_encrypt+0x68/0x158
So clear the flag at the appropriate time.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Both asn1 headers are included by rsa_helper.c, so rsa_helper.o
should explicitly depend on them.
Signed-off-by: David Michael <david.michael@coreos.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When using SGs, only heap memory (memory that is valid as per
virt_addr_valid) is allowed to be referenced. The CTR DRBG used to
reference the caller-provided memory directly in an SG. In case the
caller provided stack memory pointers, the SG mapping is not considered
to be valid. In some cases, this would even cause a paging fault.
The change adds a new scratch buffer that is used unconditionally to
catch the cases where the caller-provided buffer is not suitable for
use in an SG. The crypto operation of the CTR DRBG produces its output
with that scratch buffer and finally copies the content of the
scratch buffer to the caller's buffer.
The scratch buffer is allocated during allocation time of the CTR DRBG
as its access is protected with the DRBG mutex.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
With virtually-mapped stacks (CONFIG_VMAP_STACK=y), using the
scatterlist crypto API with stack buffers is not allowed, and with
appropriate debugging options will cause the
'BUG_ON(!virt_addr_valid(buf));' in sg_set_buf() to be triggered.
Use a heap buffer instead.
Fixes: d7db7a882d ("crypto: acomp - update testmgr with support for acomp")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch moves the core CBC implementation into a header file
so that it can be reused by drivers implementing CBC.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch converts cbc over to the skcipher interface. It also
rearranges the code to allow it to be reused by drivers.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch converts aesni (including fpu) over to the skcipher
interface. The LRW implementation has been removed as the generic
LRW code can now be used directly on top of the accelerated ECB
implementation.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently we manually filter out internal algorithms using a list
in testmgr. This is dangerous as internal algorithms cannot be
safely used even by testmgr. This patch ensures that they're never
processed by testmgr at all.
This patch also removes an obsolete bypass for nivciphers which
no longer exist.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds xts helpers that use the skcipher interface rather
than blkcipher. This will be used by aesni_intel.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds the simd skcipher helper which is meant to be
a replacement for ablk helper. It replaces the underlying blkcipher
interface with skcipher, and also presents the top-level algorithm
as an skcipher.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently all bits not set in mask are cleared in crypto_larval_lookup.
This is unnecessary as wherever the type bits are used it is always
masked anyway.
This patch removes the clearing so that we may use bits set in the
type but not in the mask for special purposes, e.g., picking up
internal algorithms.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch converts xts over to the skcipher interface. It also
optimises the implementation to be based on ECB instead of the
underlying cipher. For compatibility the existing naming scheme
of xts(aes) is maintained as opposed to the more obvious one of
xts(ecb(aes)).
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch converts lrw over to the skcipher interface. It also
optimises the implementation to be based on ECB instead of the
underlying cipher. For compatibility the existing naming scheme
of lrw(aes) is maintained as opposed to the more obvious one of
lrw(ecb(aes)).
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds the skcipher walk interface which replaces both
blkcipher walk and ablkcipher walk. Just like blkcipher walk it
can also be used for AEAD algorithms.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For consistency with the other 246 kernel configuration options,
rename CRYPT_CRC32C_VPMSUM to CRYPTO_CRC32C_VPMSUM.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Anton Blanchard <anton@samba.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
udplite conflict is resolved by taking what 'net-next' did
which removed the backlog receive method assignment, since
it is no longer necessary.
Two entries were added to the non-priv ethtool operations
switch statement, one in 'net' and one in 'net-next, so
simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
The aliasing check in map_and_copy is no longer necessary because
the IPsec ESP code no longer provides an IV that points into the
actual request data. As this check is now triggering BUG checks
due to the vmalloced stack code, I'm removing it.
Reported-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Recently an init call was added to hash_recvmsg so as to reset
the hash state in case a sendmsg call was never made.
Unfortunately this ended up clobbering the result if the previous
sendmsg was done with a MSG_MORE flag. This patch fixes it by
excluding that case when we make the init call.
Fixes: a8348bca29 ("algif_hash - Fix NULL hash crash with shash")
Reported-by: Patrick Steinhardt <ps@pks.im>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The CTR DRBG segments the number of random bytes to be generated into
128 byte blocks. The current code misses the advancement of the output
buffer pointer when the requestor asks for more than 128 bytes of data.
In this case, the next 128 byte block of random numbers is copied to
the beginning of the output buffer again. This implies that only the
first 128 bytes of the output buffer would ever be filled.
The patch adds the advancement of the buffer pointer to fill the entire
buffer.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Recently algif_hash has been changed to allow null hashes. This
triggers a bug when used with an shash algorithm whereby it will
cause a crash during the digest operation.
This patch fixes it by avoiding the digest operation and instead
doing an init followed by a final which avoids the buggy code in
shash.
This patch also ensures that the result buffer is freed after an
error so that it is not returned as a genuine hash result on the
next recv call.
The shash/ahash wrapper code will be fixed later to handle this
case correctly.
Fixes: 493b2ed3f7 ("crypto: algif_hash - Handle NULL hashes correctly")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Laura Abbott <labbott@redhat.com>
GF(2^128) multiplication tables are typically used for secret
information, so it's a good idea to zero them on free.
Signed-off-by: Alex Cope <alexcope@google.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Drop duplicate header module.h from jitterentropy-kcapi.c.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Similar to commit 14135f30e3 ("inet: fix sleeping inside inet_wait_for_connect()"),
sk_wait_event() needs to fix too, because release_sock() is blocking,
it changes the process state back to running after sleep, which breaks
the previous prepare_to_wait().
Switch to the new wait API.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code is unlikely to be useful in the future because transforms
don't know how often keys will be changed, new algorithms are unlikely
to use lle representation, and tables should be replaced with
carryless multiplication instructions when available.
Signed-off-by: Alex Cope <alexcope@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix the single instance where a positive EINVAL was returned.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
By using the unaligned access helpers, we drastically improve
performance on small MIPS routers that have to go through the exception
fix-up handler for these unaligned accesses.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Acked-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Christoph Hellwig