Trying to write console output from within the serial console driver
while the port->lock is held causes recursive deadlock:
CPU 0
spin_lock_irqsave(&port->lock)
printk()
console_unlock()
call_console_drivers()
serial8250_console_write()
spin_lock_irqsave(&port->lock)
** DEADLOCK **
The 8250_dw i/o accessors try to write a console error message if the
LCR workaround was unsuccessful. When the port->lock is already held
(eg., when called from serial8250_set_termios()), this deadlocks.
Make the error message a FIXME until a general solution is devised.
Cc: Tim Kryger <tim.kryger@gmail.com>
Reported-by: Zhang Zhen <zhenzhang.zhang@huawei.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is not recommened to use platform_get_resource(pdev, IORESOURCE_IRQ)
for requesting IRQ's resources any more, as they can be not ready yet in
case of DT-booting.
platform_get_irq() instead is a recommended way for getting IRQ even if
it was not retrieved earlier.
It also makes code simpler because we're getting "int" value right away
and no conversion from resource to int is required.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this the module does not load automatically whenever suitable
platform device appears.
Reported-by: Jerome Blin <jerome.blin@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed behaviour of get_mctrl() serial driver function as documented in:
https://www.kernel.org/doc/Documentation/serial/driver
Added device-tree properties 'dcd-override', 'dsr-override',
'cts-override', and 'ri-override' specific to the Synopsis 8250
DesignWare UART driver. Allows one to force Data Carrier Detect,
Clear To Send, and Data Set Ready signals to permanently be reported as
active. The Ring indicator can be forced to be reported as inactive.
It is possible that if modem control signalling is enabled on a port
that doesn't have these pins (e.g. - a simple two wire Tx/Rx port), the
driver can hang indefinitely waiting for the state to change. The new
DT properties allow the driver to ignore the state of these pins on
serial ports that don't support them, as recommended in the kernel
documentation.
Reviewed-by: JD (Jiandong) Zheng <jdzheng@broadcom.com>
Signed-off-by: Jonathan Richardson <jonathar@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable APM X-Gene SoC serial port functionality when using ACPI table to
initialize serial port.
Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by
the driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken
into account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should
have used from the start and drop some other unuseful KERN_ERR
messages printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool
(Prarit Bhargava).
- Fix two regressions introduced by recent commits in the OPP
library and clean up some existing minor issues in that code
(Viresh Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout
the tree (or drop it where that can be done) in order to make
it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki,
Ulf Hansson, Ludovic Desroches). There will be one more
"CONFIG_PM_RUNTIME removal" batch after this one, because some
new uses of it have been introduced during the current merge
window, but that should be sufficient to finally get rid of it.
- Make the ACPI EC driver more robust against race conditions
related to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to
disable GPEs that it has not enabled which confuses ACPICA
and makes it report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver
to make it possible to override the blacklisting of some
systems in that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS
entry for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces
witn names that reflect the IDs of the ACPI device objects
they are associated with, except for "generic" ACPI fans
(PNP ID "PNP0C0B"). That's necessary for user space thermal
management tools to be able to connect the fans with the
parts of the system they are supposed to be cooling properly.
From Srinivas Pandruvada.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5fo2
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/tty/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although the existing code appears to work on most hardware, the
hardware designers tell us that 8-bit access to the registers is not
guaranteed to be reliable. Also the OCTEON simulation environments
prohibit 8-bit accesses.
For these reasons, we use __raw_readq/__raw_writeq for OCTEON. This
code is protected with #ifdef CONFIG_64BIT so it still builds under
configurations lacking readq/writeq.
We can get rid of the #ifdef __BIG_ENDIAN, as under 64-bit accesses,
OCTEON is byte order invariant.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@auriga.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Get index of serial line from device tree using function of_alias_get_id().
If no alias is found, the 8250 core takes care of incrementing the line number.
Signed-off-by: Julien CHAUVEAU <julien.chauveau@neo-technologies.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dma pointer under struct uart_8250_port is currently left
unassigned for non-ACPI platforms. It should be pointing to the dma
member in struct dw8250_data like how it was done for ACPI, so the core
8250 code will try to request for DMA when registering the port
If DMA is not enabled in device tree, request DMA will fail and the
driver will fall back to PIO
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: JD (Jiandong) Zheng <jdzheng@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Tested-by: Scott Branden <sbranden@broadcom.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull slave-dmaengine updates from Vinod Koul:
"For dmaengine contributions we have:
- designware cleanup by Andy
- my series moving device_control users to dmanegine_xxx APIs for
later removal of device_control API
- minor fixes spread over drivers mainly mv_xor, pl330, mmp, imx-sdma
etc"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (60 commits)
serial: atmel: add missing dmaengine header
dmaengine: remove FSLDMA_EXTERNAL_START
dmaengine: freescale: remove FSLDMA_EXTERNAL_START control method
carma-fpga: move to fsl_dma_external_start()
carma-fpga: use dmaengine_xxx() API
dmaengine: freescale: add and export fsl_dma_external_start()
dmaengine: add dmaengine_prep_dma_sg() helper
video: mx3fb: use dmaengine_terminate_all() API
serial: sh-sci: use dmaengine_terminate_all() API
net: ks8842: use dmaengine_terminate_all() API
mtd: sh_flctl: use dmaengine_terminate_all() API
mtd: fsmc_nand: use dmaengine_terminate_all() API
V4L2: mx3_camer: use dmaengine_pause() API
dmaengine: coh901318: use dmaengine_terminate_all() API
pata_arasan_cf: use dmaengine_terminate_all() API
dmaengine: edma: check for echan->edesc => NULL in edma_dma_pause()
dmaengine: dw: export probe()/remove() and Co to users
dmaengine: dw: enable and disable controller when needed
dmaengine: dw: always export dw_dma_{en,dis}able
dmaengine: dw: introduce dw_dma_on() helper
...
That field has been deprecated in favour of getting the necessary information
from ACPI or DT.
However, we still need to deal systems that are PCI only (no ACPI to back up)
like Intel Bay Trail. In order to support such systems, we explicitly bind
setup() to the appropriate DMA filter function and its corresponding parameter.
Then when serial8250_request_dma() doesn't find the channel via ACPI or DT, it
falls back to use the given filter function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Another new ACPI identifier for the 8250 dw bindings to cover newer Intel
SoCs such as Braswell.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250_dw driver fails to probe if the specified clock isn't
registered at probe time. Even if a clock frequency is given,
the required clock might be gated because it wasn't properly
enabled.
This happened to me when the device is registered through DT,
and the clock was part of an MFD, the PRCM found on A31 and A23
SoCs. Unlike core clocks that are registered with OF_CLK_DECLARE,
which happen almost immediately after the kernel starts, the
clocks are registered as sub-devices of the PRCM MFD platform
device. Even though devices are registered in the order they are
found in the DT, the drivers are registered in a different,
arbitrary order. It is possible that the 8250_dw driver is
registered, and thus associated with the device and probed, before
the clock driver is registered and probed.
8250_dw then reports unable to get the clock, and fails. Without
a working console, the kernel panics.
This patch adds support for deferred probe handling for the clock
and reset controller. It also fixes the cleanup path if
serial8250_register_8250_port fails.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Allwinner A31 and A23 SoCs have a reset controller
maintaining the UART in reset by default.
This patch adds optional reset support to the driver.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It helps to cast struct uart_port to struct uart_8250_port at runtime.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First try to find the named clock variants then fall back to the already
existing handling of a nameless declared baudclk.
This also adds the missing documentation for this already existing variant.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The flags member has upf_t type and corresponding macros to define them. This
patch converts ASYNC_SKIP_TEST to UPF_SKIP_TEST in 8250_dw.c.
Otherwise we got a sparse warning:
drivers/tty/serial/8250/8250_dw.c:302:46: warning: restricted upf_t degrades to integer
drivers/tty/serial/8250/8250_dw.c:302:62: warning: restricted upf_t degrades to integer
drivers/tty/serial/8250/8250_dw.c:302:26: warning: incorrect type in assignment (different base types)
drivers/tty/serial/8250/8250_dw.c:302:26: expected restricted upf_t [usertype] flags
drivers/tty/serial/8250/8250_dw.c:302:26: got unsigned int
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This replaces the Baytrail specific custom set_termios hook
with a more generic one where the clock framework is used to
set the rate. The method also doesn't need to be limited to
just Baytrail, so it's used with all ACPI platforms.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the same manner as 8250_pci, 8250_dw needs some
baytrail specific quirks to be used. The reference
clock needs to be adjusted before divided in order
to have the minimum error rate on the baudrate.
The specific byt set termios function is stored in
the driver_data field of the acpi device id via the
dw8250_acpi_desc structure.
Remove the uartclk field which is no longer delivered
as driver data.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_PM will be set if either or both CONFIG_PM_SLEEP and
CONFIG_PM_RUNTIME is set. Compiling the driver with !CONFIG_PM_SLEEP causes
following compilation warnings:
drivers/tty/serial/8250/8250_dw.c:404:12: warning: ‘dw8250_suspend’ defined but not used [-Wunused-function]
drivers/tty/serial/8250/8250_dw.c:413:12: warning: ‘dw8250_resume’ defined but not used [-Wunused-function]
Fix this by using CONFIG_PM_SLEEP instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Newer Intel PCHs with LPSS have the same Designware controllers than
Haswell but ACPI IDs are different. Add these IDs to the driver list.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit c49436b657 (serial: 8250_dw: Improve unwritable LCR workaround)
caused a regression. It added a check that the LCR was written properly
to detect and workaround the busy quirk, but the behaviour of bit 5
(UART_LCR_SPAR) differs between IP versions 3.00a and 3.14c per the
docs. On older versions this caused the check to fail and it would
repeatedly force idle and rewrite the LCR register, causing delays and
preventing any input from serial being received.
This is fixed by masking out UART_LCR_SPAR before making the comparison.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Tim Kryger <tim.kryger@linaro.org>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: Matt Porter <matt.porter@linaro.org>
Cc: Markus Mayer <markus.mayer@linaro.org>
Tested-by: Tim Kryger <tim.kryger@linaro.org>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ACPI now provides stubs for the functions the driver uses.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When configured with UART_16550_COMPATIBLE=NO or in versions prior to
the introduction of this option, the Designware UART will ignore writes
to the LCR if the UART is busy. The current workaround saves a copy of
the last written LCR and re-writes it in the ISR for a special interrupt
that is raised when a write was ignored.
Unfortunately, interrupts are typically disabled prior to performing a
sequence of register writes that include the LCR so the point at which
the retry occurs is too late. An example is serial8250_do_set_termios()
where an ignored LCR write results in the baud divisor not being set and
instead a garbage character is sent out the transmitter.
Furthermore, since serial_port_out() offers no way to indicate failure,
a serious effort must be made to ensure that the LCR is actually updated
before returning back to the caller. This is difficult, however, as a
UART that was busy during the first attempt is likely to still be busy
when a subsequent attempt is made unless some extra action is taken.
This updated workaround reads back the LCR after each write to confirm
that the new value was accepted by the hardware. Should the hardware
ignore a write, the TX/RX FIFOs are cleared and the receive buffer read
before attempting to rewrite the LCR out of the hope that doing so will
force the UART into an idle state. While this may seem unnecessarily
aggressive, writes to the LCR are used to change the baud rate, parity,
stop bit, or data length so the data that may be lost is likely not
important. Admittedly, this is far from ideal but it seems to be the
best that can be done given the hardware limitations.
Lastly, the revised workaround doesn't touch the LCR in the ISR, so it
avoids the possibility of a "serial8250: too much work for irq" lock up.
This problem is rare in real situations but can be reproduced easily by
wiring up two UARTs and running the following commands.
# stty -F /dev/ttyS1 echo
# stty -F /dev/ttyS2 echo
# cat /dev/ttyS1 &
[1] 375
# echo asdf > /dev/ttyS1
asdf
[ 27.700000] serial8250: too much work for irq96
[ 27.700000] serial8250: too much work for irq96
[ 27.710000] serial8250: too much work for irq96
[ 27.710000] serial8250: too much work for irq96
[ 27.720000] serial8250: too much work for irq96
[ 27.720000] serial8250: too much work for irq96
[ 27.730000] serial8250: too much work for irq96
[ 27.730000] serial8250: too much work for irq96
[ 27.740000] serial8250: too much work for irq96
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stub for dw8250_probe_acpi() is missing an argument.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The channel IDs are set to -1 by default. It will prevent
dmaengine from trying to provide the first free channel if
it fails to allocate exclusive channel. This will fix an
issue with ACPI enumerated UARTs that do not support DMA
but still end up getting a DMA channel incorrectly.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It should be available for DT users as well. This does not
enable DMA by default except with ACPI. DT users can enable
DMA based on a property.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a serial port is configured for RTS/CTS flow control, serial core
will disable the transmitter if it observes CTS is de-asserted. This is
perfectly reasonable and appropriate when the UART lacks the ability to
automatically perform CTS flow control.
However, if the UART hardware can manage flow control automatically, it
is important that software not get involved. When the DesignWare UART
enables 16C750 style auto-RTS/CTS it stops generating interrupts for
changes in CTS state so software mostly stays out of the way. However,
it does report the true state of CTS in the MSR so software may notice
it is de-asserted and respond by improperly disabling the transmitter.
Once this happens the transmitter will be blocked forever.
To avoid this situation, we simply lie to the 8250 and serial core by
reporting that CTS is asserted whenever auto-RTS/CTS mode is enabled.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A few differences needed by OCTEON:
o These are DWC UARTS, but have USR at a different offset.
o Internal SoC buses require reading back from registers to maintain
write ordering.
o 8250 on OCTEON appears with 64-bit wide registers, so when using
readb/writeb in big endian mode we have to adjust the membase to hit
the proper part of the register.
o No UCV register, so we hard code some properties.
Because OCTEON doesn't have a UCV register, I change where
dw8250_setup_port(), which reads the UCV, is called by pushing it in
to the OF and ACPI probe functions, and move unchanged
dw8250_setup_port() earlier in the file.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: linux-mips@linux-mips.org
Cc: Jamie Iles <jamie@jamieiles.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/5516/
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is the same controller as on Intel Lynxpoint but the
ACPI ID is different.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ffc3ae6dd "serial: 8250_dw: Enable runtime PM" introduced runtime
PM management, which enables/disables the clk without checking if the clk
is valid. However, this driver allows to be probed without a defined clk,
using clock-frequency, as a fallback.
Therefore, on platforms that are device tree probed using clock-frequency
instead of clk, we get an ugly NULL pointer dereference.
This patch fixes it by simply adding a check before accessing the clk api.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes the stub for dw8250_probe_acpi() that is used
when compiling without ACPI enabled. The argument type was
wrong.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Designware UART has an optional support for 16750
compatible Auto Flow Control. This will enable it based on
the AFCE bit in Component Parameter Register.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new ACPI DMA helpers in dmaengine API can take care of
extracting all the necessary information regarding DMA. The
driver does not need to do this separately any more.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Lynxpoint LPSS peripheral clocks are now handled in clk
framework so the drivers do not need to take care of them
manually. In dw8250_probe_acpi(), the uartclk is now taken
from the driver_data only if it was not already set.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows ACPI to put the device to D3 when it's not used.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit implements support for using the clk api; this lets us use
the "clocks" property with device tree, instead of having to use
clock-frequency.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The default burst is often 1 byte which is not very optimal.
The ideal burst size when using 16550A type port would be
1/2 of fifosize, but this does not work with all Designware
implementations. Setting it to 1/4 fifosize.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are no stubs for ACPI functions so the driver needs to
have this ifdef or it will not compile without ACPI.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With ACPI 5.0 we can use the FixedDMA Resource Descriptor to
extract the needed information for DMA support.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds support for ACPI 5.0 enumerated Designware UARTs.
ACPI does not deliver information about uart clk, so
delivering it with the driver_data.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman