The driver should not ignore errors while registering the I2C
bus, as this device can't even minimally work without the buses,
as it uses those buses internally to talk with the several IP
blocks inside the chip.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The number of the cx231xx REQ for GPIO register set/get are wrong.
They should follow what's there at cx231xx-pcb-cfg.h.
Noticed while checking the cx231xx parser at the v4l-utils.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If something bad happens when switching between digital
and analog mode, prints an error and outputs the returned code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This device uses GPIOs: 28 to switch between analog and
digital modes: on digital mode, it should be set to 1.
The code that sets it on analog mode is OK, but it misses
the logic that sets it on digital mode.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Sometimes, the USB pipe could enter into a stalled state,
and may need a reset to rework.
Add such logic.
[mchehab@osg.samsung.com: ported from Android's source:
3a322adc00%5E%21]
Signed-off-by: Terry Heo <terryheo@google.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Pull i2c updates from Wolfram Sang:
- Peter Rosin did some major rework on the locking of i2c muxes by
seperating parent-locked muxes and mux-locked muxes.
This avoids deadlocks/workarounds when the mux itself needs i2c
commands for muxing. And as a side-effect, other workarounds in the
media layer could be eliminated. Also, Peter stepped up as the i2c
mux maintainer and will keep an eye on these changes.
- major updates to the octeon driver
- add a helper to the core to generate the address+rw_bit octal and
make drivers use it
- quite a bunch of driver updates
* 'i2c/for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (84 commits)
i2c: rcar: add DMA support
i2c: st: Implement bus clear
i2c: only check scl functions when using generic recovery
i2c: algo-bit: declare i2c_bit_quirk_no_clk_stretch as static
i2c: tegra: disable clock before returning error
[media] rtl2832: regmap is aware of lockdep, drop local locking hack
[media] rtl2832_sdr: get rid of empty regmap wrappers
[media] rtl2832: change the i2c gate to be mux-locked
[media] si2168: change the i2c gate to be mux-locked
iio: imu: inv_mpu6050: change the i2c gate to be mux-locked
i2c: mux: document i2c muxes and elaborate on parent-/mux-locked muxes
i2c: mux: relax locking of the top i2c adapter during mux-locked muxing
i2c: muxes always lock the parent adapter
i2c: allow adapter drivers to override the adapter locking
i2c: uniphier: add "\n" at the end of error log
i2c: mv64xxx: remove CONFIG_HAVE_CLK conditionals
i2c: mv64xxx: use clk_{prepare_enable,disable_unprepare}
i2c: mv64xxx: handle probe deferral for the clock
i2c: mv64xxx: enable the driver on ARCH_MVEBU
i2c: octeon: Add workaround for broken irqs on CN3860
...
We print an uninitialized "actlen" variable on the error path.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select op to be in terms of the i2c mux core instead
of the child adapter.
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The current cx231xx driver doesn't work with bulk transfer mode.
This patch makes it possible to use bulk transfer mode.
Signed-off-by: Terry Heo <terryheo@google.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The if and the else code are identical - so the condition has no effect
on the effective code.
This patch removes the condition and the duplicated code.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Unfortunately, on devices that have multiple interfaces, udev->dev
points to the parent device (usb) instead of the cx231xx specific one.
Due to that the logs don't look too nice, as they'll print messages
as if they were produced by USB core:
usb-1-2: New device Conexant Corporation Polaris AV Capturb @ 480 Mbps (1554:5010) with 7 interfaces
Instead of using the name of the parent device, let's use the name
of the first cx231xx interface for all cx231xx sub-modules.
With this path, the logs will be nicer:
cx231xx 1-2:1.1: New device Conexant Corporation Polaris AV Capturb @ 480 Mbps (1554:5010) with 7 interfaces
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that we're using dev_foo, the logs become like:
usb 1-2: DVB: registering adapter 0 frontend 0 (Fujitsu mb86A20s)...
usb 1-2: Successfully loaded cx231xx-dvb
cx231xx: Cx231xx dvb Extension initialized
It is not clear, by the logs, that usb 1-2 name is an alias for
cx231xx. So, we also need to use dvb_info() at extension load/unload.
After the patch, it will print:
usb 1-2: Cx231xx dvb Extension initialized
With is coherent with the other logs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are lots of debug printks printed with pr_info. Also, the
printk's data are not too coherent:
- there are duplicated driver name at the print format;
- function name format string differs from function to function;
- long strings broken into multiple lines;
- some printks just produce ugly reports, being almost useless
as-is.
Do a cleanup on that.
Still, there are much to be done in order to do a better printk
job on this driver, but, at least it will now be a way less
verbose, if debug printks are disabled, and some logs might
actually be useful.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It currently does just like what pr_foo() macros do. So,
replace them.
A deeper cleanup is needed, as there are lots of debug macros
printed with pr_info.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The scanning itself just fails (as before this series) but now
the correct busses are scanned.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
All switching should be done by i2c mux adapters.
Drop explicit dont_use_port_3 flag.
Drop info message about switch.
Only the removed code in start_streaming is questionable:
It did switch the port_3 flag without accessing i2c in between.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
I2C bus 1 has internally a switch. Use it as I2C_1_MUX_1 and
I2C_1_MUX_3, letting the I2C core handling the switch.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/usb/cx231xx/cx231xx-avcore.c:2226:15: warning: cast to restricted __le32
drivers/media/usb/cx231xx/cx231xx-avcore.c:2447:15: warning: cast to restricted __le32
drivers/media/usb/cx231xx/cx231xx-avcore.c:2475:15: warning: cast to restricted __le32
drivers/media/usb/cx231xx/cx231xx-avcore.c:2500:15: warning: cast to restricted __le32
drivers/media/usb/cx231xx/cx231xx-avcore.c:2647:18: warning: incorrect type in assignment (different base types)
drivers/media/usb/cx231xx/cx231xx-avcore.c:2659:21: warning: cast to restricted __le32
drivers/media/usb/cx231xx/cx231xx-dvb.c:743:57: warning: Using plain integer as NULL pointer
drivers/media/usb/cx231xx/cx231xx-dvb.c:776:57: warning: Using plain integer as NULL pointer
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for:
[2040:b130] Hauppauge WinTV 930C-HD (model 1113xx)
After loading the driver the first open to dvb device node fails.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Tested on my big-endian ppc-based test machine.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rename all USB drivers with their own directory under
drivers/media/video into drivers/media/usb and update the
building system.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab