The error message when the second image is not available is incorrect,
replace "first image" with "second image".
Fixes CoverityScan CID#1077508 ("Copy-paste error")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The comparison of err < 0 is redundant as err has been previously
been assigned to 0 and has not changed. Remove the redundant check.
Fixes CoverityScan CID#703363 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The control for +5V Power detection must also be updated when the EDID is
not present.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Originally Toshiba told us that the only way to disable HDCP was to
set the receiver in repeater mode, that would make the authentication
fail because of missing software support. It has worked fine with all
the sources we and our customers has used, until it was reported
problems with Apple MacBook (Retina, 12-inch, Early 2015)
(https://support.apple.com/kb/SP712?locale=en_US&viewlocale=en_US)
with Apple A1612 USB type-C multiport adapter
(http://www.apple.com/shop/product/MJ1K2AM/A/usb-c-digital-av-multiport-adapter)
Finally Toshiba came up with a hidden bit that is named "Manual HDCP
authentication". In this patch the original "repeater mode" concept is
removed, and the new bit is set instead.
With his patch HDCP is disabled when connected to the Apple MacBook
and all other sources we have tested so far. The Apple MacBook is
constantly trying to authenticate, but fails and continues to transmit
unencrypted video.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The number of CSI lanes that should be used is set to the CSI_CONTROL
register by indirectly writing to the CSI_CONFW register. When the
number of lanes is read back from the CSI_CONTROL register the value
is usually correct, but we have seen that it suddenly is 1 for a short
moment before the correct value is restored again.
Toshiba have not figured out why that happen, but we have found it
safer to store the value in the driver.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for v4l2_subdev_ops structures that are only passed as an
argument to the function v4l2_subdev_init. This argument is of type
const, so v4l2_subdev_ops structures having this property can also be
declared const.
Done using Coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct v4l2_subdev_ops i@p = {...};
@ok1@
identifier r1.i;
position p;
@@
v4l2_subdev_init(...,&i@p)
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct v4l2_subdev_ops i;
File size before:
text data bss dec hex filename
17171 1912 20 19103 4a9f
platform/s3c-camif/camif-capture.o
File size after:
text data bss dec hex filename
17235 1848 20 19103 4a9f
platform/s3c-camif/camif-capture.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
dib7000p_read_word() may return zero on i2c errors, resulting in
dib7000p_get_internal_freq() returning zero.
So don't divide by the result of dib7000p_get_internal_freq()
without checking it for zero in dib7000p_set_dds().
On one of my machines the device
ID 2304:0229 Pinnacle Systems, Inc. PCTV Dual DVB-T 2001e
about once a day/every two days gets into a state, where
most (all?) I2C reads return with an error. Tuning during this
state will result in a divide by zero without this patch.
This patch doesn't fix the root cause for the device getting
into a bad state, but it allows me to unload/reload the drivers,
bringing it back into a usable state.
Signed-off-by: Martin Wache <M.Wache@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2_subdev_{core/video}_ops structures are stored in the
fields of the v4l2_subdev_ops structure which are of type const.
Also, v4l2_subdev_ops structure is passed to a function
having its argument of type const. As these structures are never
modified, so declare them as const.
Done using Coccinelle: (One of the scripts used)
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct v4l2_subdev_ops i@p = {...};
@ok1@
identifier r1.i;
position p;
@@
v4l2_i2c_subdev_init(...,&i@p)
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct v4l2_subdev_ops i;
File size before:
text data bss dec hex filename
2732 608 8 3348 d14 drivers/media/i2c/ml86v7667.o
File size after:
text data bss dec hex filename
3100 232 8 3340 d0c drivers/media/i2c/ml86v7667.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2_subdev_{core/video}_ops structures are stored in the
fields of the v4l2_subdev_ops structure which are of type const.
Also, v4l2_subdev_ops structure is passed to a function
having its argument of type const. As these structures are never
modified, so declare them as const.
Done using Coccinelle: (One of the scripts used)
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct v4l2_subdev_video_ops i@p = {...};
@ok1@
identifier r1.i;
position p;
struct v4l2_subdev_ops obj;
@@
obj.video=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct v4l2_subdev_video_ops i;
File size before:
text data bss dec hex filename
1809 872 0 2681 a79 drivers/media/i2c/ak881x.o
File size after:
text data bss dec hex filename
2185 496 0 2681 a79 drivers/media/i2c/ak881x.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2_subdev_pad_ops structures are stored in the pad field
of the v4l2_subdev_ops structure and this field is of type const.
As the v4l2_subdev_pad_ops structures are never modified, they can be
declared as const.
Done using Coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct v4l2_subdev_pad_ops i@p = {...};
@ok1@
identifier r1.i;
position p;
struct v4l2_subdev_ops obj;
@@
obj.pad=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct v4l2_subdev_pad_ops i;
File size before:
text data bss dec hex filename
7633 512 20 8165 1fe5 media/i2c/m5mols/m5mols_core.o
File size after:
text data bss dec hex filename
7761 384 20 8165 1fe5 media/i2c/m5mols/m5mols_core.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This delay is in non-atomic context and it does not seem to be
time-critical so relax it to allow the timer subsystem to optimize
hrtimers.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2_subdev_{core/pad/video}_ops structures are stored in the
fields of the v4l2_subdev_ops structure which are of type const.
Also, v4l2_subdev_ops structure is passed to a function
having its argument of type const. As these structures are never
modified, so declare them as const.
Done using Coccinelle: (One of the scripts used)
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct v4l2_subdev_video_ops i@p = {...};
@ok1@
identifier r1.i;
position p;
struct v4l2_subdev_ops obj;
@@
obj.video=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct v4l2_subdev_video_ops i;
File sizes before:
text data bss dec hex filename
7810 736 16 8562 2172 drivers/media/i2c/mt9p031.o
9652 736 24 10412 28ac drivers/media/i2c/mt9v032.o
4613 552 20 5185 1441 drivers/media/i2c/noon010pc30.o
2615 552 8 3175 c67 drivers/media/i2c/s5k6a3.o
File sizes after:
text data bss dec hex filename
8322 232 16 8570 217a drivers/media/i2c/mt9p031.o
10164 232 24 10420 28b4 drivers/media/i2c/mt9v032.o
4933 232 20 5185 1441 drivers/media/i2c/noon010pc30.o
2935 232 8 3175 c67 drivers/media/i2c/s5k6a3.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2_subdev_{core/pad/video}_ops structures are stored in the
fields of the v4l2_subdev_ops structure which are of type const.
Also, v4l2_subdev_ops structure is passed to a function
having its argument of type const. As these structures are never
modified, so declare them as const.
Done using Coccinelle: (One of the scripts used)
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct v4l2_subdev_video_ops i@p = {...};
@ok1@
identifier r1.i;
position p;
struct v4l2_subdev_ops obj;
@@
obj.video=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct v4l2_subdev_video_ops i;
File size before:
text data bss dec hex filename
6170 2752 144 9066 236a media/platform/xilinx/xilinx-tpg.o
File size after:
text data bss dec hex filename
6666 2384 8 9058 2362 media/platform/xilinx/xilinx-tpg.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Two local variables will be set to an appropriate value a bit later.
Thus omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In asds configured with V4L2_ASYNC_MATCH_OF, the v4l2 subdev can be
part of a devicetree overlay, for example:
&media_bridge {
...
my_port: port@0 {
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
ep: endpoint@0 {
remote-endpoint = <&camera0>;
};
};
};
/ {
fragment@0 {
target = <&i2c0>;
__overlay__ {
my_cam {
compatible = "foo,bar";
port {
camera0: endpoint {
remote-endpoint = <&my_port>;
...
};
};
};
};
};
};
Each time the overlay is applied, its of_node pointer will be
different. We are not interested in matching the pointer, what we
want to match is that the path is the one we are expecting. Change to
use of_node_cmp() so that we continue matching after the overlay has
been removed and reapplied.
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Javi Merino <javi.merino@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The value of return variable ret is 0 on some error paths, for example,
when pci_resource_start() returns a NULL pointer. 0 means no error in
this context, which is contrary to the fact. This patch fixes the bug.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=189011
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Function bdisp_debugfs_create() returns 0 even on errors. So its caller
cannot detect the errors. It may be better to return "-ENOMEM" on the
exception paths.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188801
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Also remove the code using size-0 OUTPUT buffer to flush.
Signed-off-by: Tiffany Lin <tiffany.lin@mediatek.com>
Signed-off-by: Wu-Cheng Li <wuchengli@chromium.org>
Reviewed-by: Kuang-che Wu <kcwu@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
gcc isn't smart enough to realize it can share most of the argument
buildup and the actual function call between the two branches, so help
it a little.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It takes more .text to initialize these on the stack than they occupy
in .rodata, so just make them static const.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
ibuf and rbuf in lme2510_int_response are always assigned to before they
are read, and their addresses do not escape the function, so they have
no reason to be static.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Using the %ph printf extension for hex dumps like this makes the
generated code quite a bit smaller.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Drivers might try to access and run enable_source and disable_source
handlers when the driver that implements these handlers is clearing
the handlers during its unregister.
Fix the following race condition:
process 1 process 2
request video streaming unbind au0828
v4l2 checks if tuner is free
... ...
au0828_unregister_media_device()
... ...
(doesn't hold graph_mutex)
mdev->enable_source = NULL;
if (mdev && mdev->enable_source) mdev->disable_source = NULL;
mdev->enable_source()
(enable_source holds graph_mutex)
As shown above enable_source check is done without holding the graph_mutex.
If unbind happens to be in progress, au0828 could clear enable_source and
disable_source handlers leading to null pointer de-reference.
Fix it by protecting enable_source and disable_source set and clear and
protecting enable_source and disable_source handler access and the call
itself.
process 1 process 2
request video streaming unbind au0828
v4l2 checks if tuner is free
... ...
au0828_unregister_media_device()
... ...
(hold graph_mutex while clearing)
mdev->enable_source = NULL;
if (mdev) mdev->disable_source = NULL;
(hold graph_mutex to check and
call enable_source)
if (mdev->enable_source)
mdev->enable_source()
If graph_mutex is held to just heck for handler being null and needs to be
released before calling the handler, there will be another window for the
handlers to be cleared. Hence, enable_source and disable_source handlers
no longer hold the graph_mutex and expect callers to hold it to avoid
forcing them release the graph_mutex before calling the handlers.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Using sprintf() with a non-literal string makes some compiler complain
when building with -Wformat-security (eg. clang reports "format string
is not a string literal (potentially insecure)").
Here sprintf() format parameter is indirectly a literal string so there
is no security issue. Nevertheless adding a "%s" format string to
silent the warning helps to detect real bugs in the kernel.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The check assumes that we end on zero but actually we end on -1. Change
the post-op to a pre-op so that we do end on zero. Techinically now we
only loop 499 times instead of 500 but that's fine.
Fixes: dc12b12435 ("[media] media: ti-vpe: vpdma: Add abort channel desc and cleanup APIs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix to avoid possible memory leak if the decoder initialization got failed.
Free the allocated memory for file handle object before return in case
decoder initialization fails.
Signed-off-by: Shailendra Verma <shailendra.v@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The FE_SUPPORTED() macro is basically the same as IS_REACHABLE, except
that it causes a warning with gcc-7:
common/b2c2/flexcop-fe-tuner.c:30:1: error: this use of "defined" may not be portable [-Werror=expansion-to-defined]
common/b2c2/flexcop-fe-tuner.c:30:1: error: this use of "defined" may not be portable [-Werror=expansion-to-defined]
common/b2c2/flexcop-fe-tuner.c:30:1: error: this use of "defined" may not be portable [-Werror=expansion-to-defined]
Using IS_REACHABLE() to define it avoids the warning.
Fixes: 3785bc170f ("[media] b2c2: break it into common/pci/usb directories")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
changeset da8ec560e3 ("[media] ivtv: implement new decoder command
ioctls") implemented proper support for mpeg audio and video control
at V4L2 API. Since then, the usage of the the DVB APIs is deprecated.
However, we never actually marked it as deprecated nor provided any
way to disable it. Let's do it now.
This patch prepares for the removal of this bad usage on a couple
of Kernel versions.
Fixes: da8ec560e3 ("[media] ivtv: implement new decoder command ioctls")
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove unused demod driver. Device that used it never went public.
If someone later decide to add support for a device using this
chipset, it should be easy enough to retrieve it from git
history.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
I saw from ZyDAS ZD1301 sniffs it sets chip sleeping by using
REG_MISC_CTRL. That has very huge effect for power management, around
0.9W. Sleep is still disabled for all the old hardware just to avoid
possible regression as meaning of register bits are unknown.
I tested it also with some other devices and it seems to be working,
but I still consider it to be too risky to change it default.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
ZyDAS ZD1301 is chip having USB interface and DVB-T demodulator
integrated. This driver is for USB interface part.
Device has USB ID 0ace:13a1. Used tuner is MT2060.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
ZyDAS ZD1301 is chip having USB interface and DVB-T demodulator
integrated. This driver is for demodulator part.
Driver is very reduced, just basic demodulator functionality, no
statistics at all. It registers as a platform driver to driver core.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add configuration parameter to split long i2c writes as some I2C
adapters cannot write 10 bytes used as a one go.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pr_foo() provides a convenient way for printk's, enforcing
that they'll all prepend the error message with the driver's
name.
Use it inside ivtv.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Move the pr_fmt() macro to ivtv_driver.h and ensure that it
will be the first file to be included on all ivtv files.
While here, put the includes inside ivtv-driver.h on
alphabetic order.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As reported by gcc:
drivers/media/platform/sti/hva/hva-v4l2.c:227:6: warning: no previous prototype for 'hva_dbg_summary' [-Wmissing-prototypes]
void hva_dbg_summary(struct hva_ctx *ctx)
^~~~~~~~~~~~~~~
This function is used only internally, so make it static.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch creates 4 static debugfs entries to dump:
- the device-related information ("st-hva/device")
- the list of registered encoders ("st-hva/encoders")
- the current values of the hva registers ("st-hva/regs")
- the information about the last closed instance ("st-hva/last")
It also creates dynamically a debugfs entry for each opened instance,
("st-hva/<instance identifier>") to dump:
- the information about the frame (format, resolution)
- the information about the stream (format, profile, level,
resolution)
- the control parameters (bitrate mode, framerate, GOP size...)
- the potential (system, encoding...) errors
- the performance information about the encoding (HW processing
duration, average bitrate, average framerate...)
Each time a running instance is closed, its context (including the
debug information) is saved to feed, on demand, the last closed
instance debugfs entry.
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Jean-Christophe Trotin <jean-christophe.trotin@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds a short summary about the encoding operation at each
instance closing, for debug purpose (through dev_dbg()):
- information about the frame (format, resolution)
- information about the stream (format, profile, level, resolution)
- number of encoded frames
- potential (system, encoding...) errors
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Jean-Christophe Trotin <jean-christophe.trotin@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
ulseep_range() uses hrtimers and provides no advantage over msleep()
for larger delays. Fix up the 25ms delays here to use msleep() and
reduce the load on the hrtimer subsystem.
Link: http://lkml.org/lkml/2017/1/11/377
Reviwed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The gpiod API checks for NULL descriptors, there's no need to duplicate
the check in the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Despite checkpatch comments, it seems that ARM doesn't like
to use constified structs.
As reported by kernel build robot:
In file included from drivers/media/platform/coda/imx-vdoa.c:22:0:
drivers/media/platform/coda/imx-vdoa.c: In function 'vdoa_driver_init':
>> include/linux/device.h:1461:20: warning: passing argument 1 of '__platform_driver_register' discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
return __register(&(__driver) , ##__VA_ARGS__); \
^
include/linux/platform_device.h:198:29: note: in definition of macro 'platform_driver_register'
__platform_driver_register(drv, THIS_MODULE)
^~~
include/linux/platform_device.h:228:2: note: in expansion of macro 'module_driver'
module_driver(__platform_driver, platform_driver_register, \
^~~~~~~~~~~~~
>> drivers/media/platform/coda/imx-vdoa.c:333:1: note: in expansion of macro 'module_platform_driver'
module_platform_driver(vdoa_driver);
^~~~~~~~~~~~~~~~~~~~~~
include/linux/platform_device.h:199:12: note: expected 'struct platform_driver *' but argument is of type 'const struct platform_driver *'
extern int __platform_driver_register(struct platform_driver *,
^~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/media/platform/coda/imx-vdoa.c:18:0:
drivers/media/platform/coda/imx-vdoa.c: In function 'vdoa_driver_exit':
>> include/linux/device.h:1466:15: warning: passing argument 1 of 'platform_driver_unregister' discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
__unregister(&(__driver) , ##__VA_ARGS__); \
^
include/linux/platform_device.h:228:2: note: in expansion of macro 'module_driver'
module_driver(__platform_driver, platform_driver_register, \
^~~~~~~~~~~~~
>> drivers/media/platform/coda/imx-vdoa.c:333:1: note: in expansion of macro 'module_platform_driver'
module_platform_driver(vdoa_driver);
^~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/media/platform/coda/imx-vdoa.c:22:0:
include/linux/platform_device.h:201:13: note: expected 'struct platform_driver *' but argument is of type 'const struct platform_driver *'
extern void platform_driver_unregister(struct platform_driver *);
^~~~~~~~~~~~~~~~~~~~~~~~~~
So, let's just remove it.
This reverts commit 126f52b02e.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Both functions initialize the file handle with v4l2_fh_init() and thus
need to call clean up with v4l2_fh_exit() as appropriate. Fix it.
Signed-off-by: Shailendra Verma <shailendra.v@samsung.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Both functions initialize the file handle with v4l2_fh_init() and thus
need to call clean up with v4l2_fh_exit() as appropriate. Fix it.
Signed-off-by: Shailendra Verma <shailendra.v@samsung.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The device driver should keep going even if debugfs initialization fails.
So, change the return type to void.
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Colin Ian King