Remove dependency on CRYPTO_DEV_FSL_CAAM where superfluous:
depends on CRYPTO_DEV_FSL_CAAM && CRYPTO_DEV_FSL_CAAM_JR
is equivalent to
depends on CRYPTO_DEV_FSL_CAAM_JR
since CRYPTO_DEV_FSL_CAAM_JR depends on CRYPTO_DEV_FSL_CAAM.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
A few descriptor commands are generated using generic
inline append "append_cmd" function.
Rewrite them using specific inline append functions.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For authenc / stitched AEAD algorithms, check independently
each of the two (authentication, encryption) keys whether inlining
is possible.
Prioritize the inlining of the authentication key, since the length
of the (split) key is bigger than that of the encryption key.
For the other algorithms, compute only once per tfm the remaining
available bytes and decide whether key inlining is possible
based on this.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Information carried by alg_op can be deduced from adata->algtype
plus some fixed flags.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In preparation of factoring out the shared descriptors,
struct alginfo is introduced to group the algorithm related
parameters.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
append_key_aead() is used in only one place, thus inline it.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Building the caam driver on arm64 produces a harmless warning:
drivers/crypto/caam/caamalg.c:140:139: warning: comparison of distinct pointer types lacks a cast
We can use min_t to tell the compiler which type we want it to use
here.
Fixes: 5ecf8ef910 ("crypto: caam - fix sg dump")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Shared descriptors used by ahash_final() and ahash_finup()
are identical, thus get rid of one of them (sh_desc_finup).
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The pointer to the descriptor buffer is not touched,
it always points to start of the descriptor buffer.
Thus, make it const.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
sec4_sg_entry structure is used only by helper functions in sg_sw_sec4.h.
Since SEC HW S/G entries are to be manipulated only indirectly, via these
functions, move sec4_sg_entry to the corresponding header.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This reverts commit 66d2e20280.
Quoting from Russell's findings:
https://www.mail-archive.com/linux-crypto@vger.kernel.org/msg21136.html
[quote]
Okay, I've re-tested, using a different way of measuring, because using
openssl speed is impractical for off-loaded engines. I've decided to
use this way to measure the performance:
dd if=/dev/zero bs=1048576 count=128 | /usr/bin/time openssl dgst -md5
For the threaded IRQs case gives:
0.05user 2.74system 0:05.30elapsed 52%CPU (0avgtext+0avgdata 2400maxresident)k
0.06user 2.52system 0:05.18elapsed 49%CPU (0avgtext+0avgdata 2404maxresident)k
0.12user 2.60system 0:05.61elapsed 48%CPU (0avgtext+0avgdata 2460maxresident)k
=> 5.36s => 25.0MB/s
and the tasklet case:
0.08user 2.53system 0:04.83elapsed 54%CPU (0avgtext+0avgdata 2468maxresident)k
0.09user 2.47system 0:05.16elapsed 49%CPU (0avgtext+0avgdata 2368maxresident)k
0.10user 2.51system 0:04.87elapsed 53%CPU (0avgtext+0avgdata 2460maxresident)k
=> 4.95 => 27.1MB/s
which corresponds to an 8% slowdown for the threaded IRQ case. So,
tasklets are indeed faster than threaded IRQs.
[...]
I think I've proven from the above that this patch needs to be reverted
due to the performance regression, and that there _is_ most definitely
a deterimental effect of switching from tasklets to threaded IRQs.
[/quote]
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
alkcipher_edesc_alloc() and ablkcipher_giv_edesc_alloc() don't
free / unmap resources on error path:
- dmap_map_sg() could fail, thus make sure the return value is checked
- unmap DMA mappings in case of error
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
ERRID is a 4-bit field.
Since err_id values are in [0..15] and err_id_list array size is 16,
the condition "err_id < ARRAY_SIZE(err_id_list)" is always true.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
REG3 no longer needs to be updated, since it's not used after that.
This shared descriptor command is a leftover of the conversion to
AEAD interface.
Fixes: 479bcc7c5b "crypto: caam - Convert authenc to new AEAD interface"
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix the following smatch warnings:
drivers/crypto/caam/caamalg.c:2350 aead_edesc_alloc() warn: we tested 'src_nents' before and it was 'true'
drivers/crypto/caam/caamrng.c:351 caam_rng_init() error: no modifiers for allocation.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
1. fix HDR_START_IDX_MASK, HDR_SD_SHARE_MASK, HDR_JD_SHARE_MASK
Define HDR_START_IDX_MASK consistently with the other masks:
mask = bitmask << offset
2. OP_ALG_TYPE_CLASS1 and OP_ALG_TYPE_CLASS2 must be shifted.
3. fix FIFO_STORE output data type value for AFHA S-Box
4. fix OPERATION pkha modular arithmetic source mask
5. rename LDST_SRCDST_WORD_CLASS1_ICV_SZ to
LDST_SRCDST_WORD_CLASS1_IV_SZ (it refers to IV, not ICV).
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Commit 4464a7d4f5
("crypto: caam - remove error propagation handling")
removed error propagation handling only from caamalg.
Do this in all other places: caamhash, caamrng.
Update descriptors' lengths appropriately.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The AEAD givenc descriptor relies on moving the IV through the
output FIFO and then back to the CTX2 for authentication. The
SEQ FIFO STORE could be scheduled before the data can be
read from OFIFO, especially since the SEQ FIFO LOAD needs
to wait for the SEQ FIFO LOAD SKIP to finish first. The
SKIP takes more time when the input is SG than when it's
a contiguous buffer. If the SEQ FIFO LOAD is not scheduled
before the STORE, the DECO will hang waiting for data
to be available in the OFIFO so it can be transferred to C2.
In order to overcome this, first force transfer of IV to C2
by starting the "cryptlen" transfer first and then starting to
store data from OFIFO to the output buffer.
Fixes: 1acebad3d8 ("crypto: caam - faster aead implementation")
Cc: <stable@vger.kernel.org> # 3.2+
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When using AES-XTS on a Wandboard, we receive a Mode error:
caam_jr 2102000.jr1: 20001311: CCB: desc idx 19: AES: Mode error.
According to the Security Reference Manual, the Low Power AES units
of the i.MX6 do not support the XTS mode. Therefore we must not
register XTS implementations in the Crypto API.
Signed-off-by: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Cc: <stable@vger.kernel.org> # 4.4+
Fixes: c6415a6016 "crypto: caam - add support for acipher xts(aes)"
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Building the caam driver on arm64 produces a harmless warning:
drivers/crypto/caam/caamalg.c:140:139: warning: comparison of distinct pointer types lacks a cast
We can use min_t to tell the compiler which type we want it to use
here.
Fixes: 5ecf8ef910 ("crypto: caam - fix sg dump")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
i.MX6UL does only require three clocks to enable CAAM module.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Even for i.MX, CAAM is able to use address pointers greater than
32 bits, the address pointer field being interpreted as a double word.
Enforce u64 address pointer in the sec4_sg_entry struct.
This patch fixes the SGT address pointer endianness issue for
32bit platforms where core endianness != caam endianness.
Signed-off-by: Tudor Ambarus <tudor-dan.ambarus@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Free memory mapping, if probe is not successful.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Ensure scatterlists have a virtual memory mapping before dumping.
Signed-off-by: Catalin Vasile <cata.vasile@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move statements for error handling which were identical
in two if branches to the end of these functions.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The local variable "ret" will be set to an appropriate value a bit later.
Thus omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* Return a value at the end without storing it in an intermediate variable.
* Delete the local variable "ret" which became unnecessary with
this refactoring.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Adjust jump labels according to the current Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Adjust jump labels according to the current Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "kmalloc_array".
This issue was detected by using the Coccinelle software.
* Replace the specification of a data type by a pointer dereference
to make the corresponding size determination a bit safer according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
-nonce is being loaded using append_load_imm_u32() instead of
append_load_as_imm() (nonce is a byte array / stream, not a 4-byte
variable)
-counter is not being added in big endian format, as mandatated by
RFC3686 and expected by the crypto engine
Signed-off-by: Catalin Vasile <cata.vasile@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
We get 1 warning when biuld kernel with W=1:
drivers/crypto/caam/ctrl.c:398:5: warning: no previous prototype for 'caam_get_era' [-Wmissing-prototypes]
In fact, this function is declared in drivers/crypto/caam/ctrl.h,
so this patch add missing header dependencies.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For algorithms that implement IV generators before the crypto ops,
the IV needed for decryption is initially located in req->src
scatterlist, not in req->iv.
Avoid copying the IV into req->iv by modifying the (givdecrypt)
descriptors to load it directly from req->src.
aead_givdecrypt() is no longer needed and goes away.
Cc: <stable@vger.kernel.org> # 4.3+
Fixes: 479bcc7c5b ("crypto: caam - Convert authenc to new AEAD interface")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Threaded interrupts can perform the function of the tasklet, and much
more safely too - without races when trying to take the tasklet and
interrupt down on device removal.
With the old code, there is a window where we call tasklet_kill(). If
the interrupt handler happens to be running on a different CPU, and
subsequently calls tasklet_schedule(), the tasklet will be re-scheduled
for execution.
Switching to a hardirq/threadirq combination implementation avoids this,
and it also means generic code deals with the teardown sequencing of the
threaded and non-threaded parts.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add a helper to map the source scatterlist into the descriptor.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add a helper function to perform the descriptor allocation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Strictly, dma_map_sg() may coalesce SG entries, but in practise on iMX
hardware, this will never happen. However, dma_map_sg() can fail, and
we completely fail to check its return value. So, fix this properly.
Arrange the code to map the scatterlist early, so we know how many
scatter table entries to allocate, and then fill them in. This allows
us to keep relatively simple error cleanup paths.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Ensure that we clean up allocations and DMA mappings after encountering
an error rather than just giving up and leaking memory and resources.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Since the extended descriptor includes the hardware descriptor, and the
sec4 scatterlist immediately follows this, we can declare it as a array
at the very end of the extended descriptor. This allows us to get rid
of an initialiser for every site where we allocate an extended
descriptor.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Mark the hardware descriptor as being cache line aligned; on DMA
incoherent architectures, the hardware descriptor should sit in a
separate cache line from the CPU accessed data to avoid polluting
the caches.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Rather than giving the descriptor as hw_desc[0], give it's real size.
All places where we allocate an ahash_edesc incorporate DESC_JOB_IO_LEN
bytes of job descriptor.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
caamhash contains this weird code:
src_nents = sg_count(req->src, req->nbytes);
dma_map_sg(jrdev, req->src, src_nents ? : 1, DMA_TO_DEVICE);
...
edesc->src_nents = src_nents;
sg_count() returns zero when sg_nents_for_len() returns zero or one.
This means we don't need to use a hardware scatterlist. However,
setting src_nents to zero causes problems when we unmap:
if (edesc->src_nents)
dma_unmap_sg_chained(dev, req->src, edesc->src_nents,
DMA_TO_DEVICE, edesc->chained);
as zero here means that we have no entries to unmap. This causes us
to leak DMA mappings, where we map one scatterlist entry and then
fail to unmap it.
This can be fixed in two ways: either by writing the number of entries
that were requested of dma_map_sg(), or by reworking the "no SG
required" case.
We adopt the re-work solution here - we replace sg_count() with
sg_nents_for_len(), so src_nents now contains the real number of
scatterlist entries, and we then change the test for using the
hardware scatterlist to src_nents > 1 rather than just non-zero.
This change passes my sshd, openssl tests hashing /bin and tcrypt
tests.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Since 6de62f15b5 ("crypto: algif_hash - Require setkey before
accept(2)"), the AF_ALG interface requires userspace to provide a key
to any algorithm that has a setkey method. However, the non-HMAC
algorithms are not keyed, so setting a key is unnecessary.
Fix this by removing the setkey method from the non-keyed hash
algorithms.
Fixes: 6de62f15b5 ("crypto: algif_hash - Require setkey before accept(2)")
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
To be able to generate shared descriptors for AEAD, the authentication size
needs to be known. However, there is no imposed order of calling .setkey,
.setauthsize callbacks.
Thus, in case authentication size is not known at .setkey time, defer it
until .setauthsize is called.
The authsize != 0 check was incorrectly removed when converting the driver
to the new AEAD interface.
Cc: <stable@vger.kernel.org> # 4.3+
Fixes: 479bcc7c5b ("crypto: caam - Convert authenc to new AEAD interface")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There are a few things missed by the conversion to the
new AEAD interface:
1 - echainiv(authenc) encrypt shared descriptor
The shared descriptor is incorrect: due to the order of operations,
at some point in time MATH3 register is being overwritten.
2 - buffer used for echainiv(authenc) encrypt shared descriptor
Encrypt and givencrypt shared descriptors (for AEAD ops) are mutually
exclusive and thus use the same buffer in context state: sh_desc_enc.
However, there's one place missed by s/sh_desc_givenc/sh_desc_enc,
leading to errors when echainiv(authenc(...)) algorithms are used:
DECO: desc idx 14: Header Error. Invalid length or parity, or
certain other problems.
While here, also fix a typo: dma_mapping_error() is checking
for validity of sh_desc_givenc_dma instead of sh_desc_enc_dma.
Cc: <stable@vger.kernel.org> # 4.3+
Fixes: 479bcc7c5b ("crypto: caam - Convert authenc to new AEAD interface")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add RSA support to caam driver.
Initial author is Yashpal Dutta <yashpal.dutta@freescale.com>.
Signed-off-by: Tudor Ambarus <tudor-dan.ambarus@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
EXTRA_CFLAGS is still supported but its usage is deprecated.
Signed-off-by: Tudor Ambarus <tudor-dan.ambarus@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This basically adds support for ls1043a platform.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There are SoCs like LS1043A where CAAM endianness (BE) does not match
the default endianness of the core (LE).
Moreover, there are requirements for the driver to handle cases like
CPU_BIG_ENDIAN=y on ARM-based SoCs.
This requires for a complete rewrite of the I/O accessors.
PPC-specific accessors - {in,out}_{le,be}XX - are replaced with
generic ones - io{read,write}[be]XX.
Endianness is detected dynamically (at runtime) to allow for
multiplatform kernels, for e.g. running the same kernel image
on LS1043A (BE CAAM) and LS2080A (LE CAAM) armv8-based SoCs.
While here: debugfs entries need to take into consideration the
endianness of the core when displaying data. Add the necessary
glue code so the entries remain the same, but they are properly
read, regardless of the core and/or SEC endianness.
Note: pdb.h fixes only what is currently being used (IPsec).
Reviewed-by: Tudor Ambarus <tudor-dan.ambarus@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The offset field is 13 bits wide; make sure we don't overwrite more than
that in the caam hardware scatter gather structure.
Signed-off-by: Cristian Stoica <cristian.stoica@freescale.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Most users of IS_ERR_VALUE() in the kernel are wrong, as they
pass an 'int' into a function that takes an 'unsigned long'
argument. This happens to work because the type is sign-extended
on 64-bit architectures before it gets converted into an
unsigned type.
However, anything that passes an 'unsigned short' or 'unsigned int'
argument into IS_ERR_VALUE() is guaranteed to be broken, as are
8-bit integers and types that are wider than 'unsigned long'.
Andrzej Hajda has already fixed a lot of the worst abusers that
were causing actual bugs, but it would be nice to prevent any
users that are not passing 'unsigned long' arguments.
This patch changes all users of IS_ERR_VALUE() that I could find
on 32-bit ARM randconfig builds and x86 allmodconfig. For the
moment, this doesn't change the definition of IS_ERR_VALUE()
because there are probably still architecture specific users
elsewhere.
Almost all the warnings I got are for files that are better off
using 'if (err)' or 'if (err < 0)'.
The only legitimate user I could find that we get a warning for
is the (32-bit only) freescale fman driver, so I did not remove
the IS_ERR_VALUE() there but changed the type to 'unsigned long'.
For 9pfs, I just worked around one user whose calling conventions
are so obscure that I did not dare change the behavior.
I was using this definition for testing:
#define IS_ERR_VALUE(x) ((unsigned long*)NULL == (typeof (x)*)NULL && \
unlikely((unsigned long long)(x) >= (unsigned long long)(typeof(x))-MAX_ERRNO))
which ends up making all 16-bit or wider types work correctly with
the most plausible interpretation of what IS_ERR_VALUE() was supposed
to return according to its users, but also causes a compile-time
warning for any users that do not pass an 'unsigned long' argument.
I suggested this approach earlier this year, but back then we ended
up deciding to just fix the users that are obviously broken. After
the initial warning that caused me to get involved in the discussion
(fs/gfs2/dir.c) showed up again in the mainline kernel, Linus
asked me to send the whole thing again.
[ Updated the 9p parts as per Al Viro - Linus ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.org/lkml/2016/1/7/363
Link: https://lkml.org/lkml/2016/5/27/486
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> # For nvmem part
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
caam_jr_alloc() used to return NULL if a JR device could not be
allocated for a session. In turn, every user of this function used
IS_ERR() function to verify if anything went wrong, which does NOT look
for NULL values. This made the kernel crash if the sanity check failed,
because the driver continued to think it had allocated a valid JR dev
instance to the session and at some point it tries to do a caam_jr_free()
on a NULL JR dev pointer.
This patch is a fix for this issue.
Cc: <stable@vger.kernel.org>
Signed-off-by: Catalin Vasile <cata.vasile@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
caam_jr_shutdown() is only used in this file, so it can be
made static.
This avoids the following sparse warning:
drivers/crypto/caam/jr.c:68:5: warning: symbol 'caam_jr_shutdown' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Increasing CAAM DMA engine transaction size either
-reduces the number of required transactions or
-adds the ability to transfer more data with same transaction count
Signed-off-by: Horia Geant? <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Previous change (see "Fixes" tag) to the MCFGR register
clears AWCACHE[0] ("bufferable" AXI3 attribute) (which is "1" at POR).
This makes all writes non-bufferable, causing a ~ 5% performance drop
for PPC-based platforms.
Rework previous change such that MCFGR[AWCACHE]=4'b0011
(bufferable + cacheable) for all platforms.
Note: For ARM-based platforms, AWCACHE[0] is ignored
by the interconnect IP.
Cc: <stable@vger.kernel.org> # 4.3+
Fixes: f109674951 ("crypto: caam - fix snooping for write transactions")
Signed-off-by: Horia Geant? <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When buffer 0 is used we should use buflen_0 instead of buflen_1.
Fix it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The sg_nents_for_len() function could fail, this patch add a check for
its return value.
We do the same for sg_count since it use sg_nents_for_len().
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The kernel's coding style suggests that closing braces for initialisers
should not be aligned to the open brace column. The CodingStyle doc
shows how this should be done. Remove the additional tab.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Avoid exporting lots of state by only exporting what we really require,
which is the buffer containing the set of pending bytes to be hashed,
number of pending bytes, the context buffer, and the function pointer
state. This reduces down the exported state size to 216 bytes from
576 bytes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
caam does not properly calculate the size of the retained state
when non-block aligned hashes are requested - it uses the wrong
buffer sizes, which results in errors such as:
caam_jr 2102000.jr1: 40000501: DECO: desc idx 5: SGT Length Error. The descriptor is trying to read more data than is contained in the SGT table.
We end up here with:
in_len 0x46 blocksize 0x40 last_bufsize 0x0 next_bufsize 0x6
to_hash 0x40 ctx_len 0x28 nbytes 0x20
which results in a job descriptor of:
jobdesc@889: ed03d918: b0861c08 3daa0080 f1400000 3d03d938
jobdesc@889: ed03d928: 00000068 f8400000 3cde2a40 00000028
where the word at 0xed03d928 is the expected data size (0x68), and a
scatterlist containing:
sg@892: ed03d938: 00000000 3cde2a40 00000028 00000000
sg@892: ed03d948: 00000000 3d03d100 00000006 00000000
sg@892: ed03d958: 00000000 7e8aa700 40000020 00000000
0x68 comes from 0x28 (the context size) plus the "in_len" rounded down
to a block size (0x40). in_len comes from 0x26 bytes of unhashed data
from the previous operation, plus the 0x20 bytes from the latest
operation.
The fixed version would create:
sg@892: ed03d938: 00000000 3cde2a40 00000028 00000000
sg@892: ed03d948: 00000000 3d03d100 00000026 00000000
sg@892: ed03d958: 00000000 7e8aa700 40000020 00000000
which replaces the 0x06 length with the correct 0x26 bytes of previously
unhashed data.
This fixes a previous commit which erroneously "fixed" this due to a
DMA-API bug report; that commit indicates that the bug was caused via a
test_ahash_pnum() function in the tcrypt module. No such function has
ever existed in the mainline kernel. Given that the change in this
commit has been tested with DMA API debug enabled and shows no issue,
I can only conclude that test_ahash_pnum() was triggering that bad
behaviour by CAAM.
Fixes: 7d5196aba3 ("crypto: caam - Correct DMA unmap size in ahash_update_ctx()")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When exporting and importing the hash state, we will only export and
import into hashes which share the same struct crypto_ahash pointer.
(See hash_accept->af_alg_accept->hash_accept_parent.)
This means that saving the caam_hash_ctx structure on export, and
restoring it on import is a waste of resources. So, remove this code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Print the errno code when hash registration fails, so we know why the
failure occurred. This aids debugging.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for AES working in XEX-based Tweaked-codebook mode with
ciphertext Stealing (XTS)
sector index - HW limitation: CAAM device supports sector index of only
8 bytes to be used for sector index inside IV, instead of whole 16 bytes
received on request. This represents 2 ^ 64 = 16,777,216 Tera of possible
values for sector index.
Signed-off-by: Cristian Hristea <cristi.hristea@gmail.com>
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Catalin Vasile <catalin.vasile@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The caam driver use two dma_map_sg path according to SG are chained
or not.
Since dma_map_sg can handle both case, clean the code with all
references to sg chained.
Thus removing dma_map_sg_chained, dma_unmap_sg_chained
and __sg_count functions.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Commit a1efb01fec ("jump_label, locking/static_keys: Rename
JUMP_LABEL_TYPE_* and related helpers to the static_key* pattern")
introduced the definition of JUMP_TYPE_MASK in
include/linux/jump_label.h causing the following name collision:
In file included from drivers/crypto/caam/desc_constr.h:7:0,
from drivers/crypto/caam/ctrl.c:15:
drivers/crypto/caam/desc.h:1495:0: warning: "JUMP_TYPE_MASK" redefined
#define JUMP_TYPE_MASK (0x03 << JUMP_TYPE_SHIFT)
^
In file included from include/linux/module.h:19:0,
from drivers/crypto/caam/compat.h:9,
from drivers/crypto/caam/ctrl.c:11:
include/linux/jump_label.h:131:0: note: this is the location of the previous definition
#define JUMP_TYPE_MASK 1UL
As JUMP_TYPE_MASK definition in desc.h is never used, we can safely remove
it to avoid the name collision.
Reported-by: Olof's autobuilder <build@lixom.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
"The preferred form for passing a size of a struct is the following:
p = kmalloc(sizeof(*p), ...);
....
The preferred form for allocating a zeroed array is the following:
p = kcalloc(n, sizeof(...), ...); "
,so do as suggested.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Instead of propagating a 'fake' error code, just propagate the real
one in the case of caam_drv_identify_clk() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In the error path we should disable the resources that were previously
acquired, so fix the error handling accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Most significant part of JQCR (Job Queue Control Register) contains
bits that control endianness: ILE - Immediate Little Endian,
DWS - Double Word Swap.
The bits are automatically set by the Job Queue Controller HW.
Unfortunately these bits are cleared in SW when submitting descriptors
via the register-based service interface.
>From LS1021A:
JQCR_MS = 08080100 - before writing: ILE | DWS | SRC (JR0)
JQCR_MS = 30000100 - after writing: WHL | FOUR | SRC (JR0)
This would cause problems on little endian caam for descriptors
containing immediata data or double-word pointers.
Currently there is no problem since the only descriptors ran through
this interface are the ones that (un)instantiate RNG.
Signed-off-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
LS1021A is a QorIQ SoC having little endian CAAM.
There are a few differences b/w QorIQ and i.MX from CAAM perspective:
1. i.MX platforms are somewhat special wrt. 64-bit registers:
-big endian format at 64-bit level: MSW at address+0 and LSW at address+4
-little endian format at 32-bit level (within MSW and LSW)
and thus need special handling.
2. No CCM (clock controller module) for QorIQ.
No CAAM clocks to enable / disable.
A new Kconfig option - CRYPTO_DEV_FSL_CAAM_LE - is added to indicate
CAAM is little endian (*). It is hidden from the user (to avoid
misconfiguration); when adding support for a new platform with LE CAAM,
either the Kconfig needs to be updated or the corresponding defconfig
needs to indicate that CAAM is LE.
(*) Using a DT property to provide CAAM endianness would not allow
for the ifdeffery.
In order to keep changes to a minimum, the following changes
are postponed:
-endianness fix of the last word in the S/G (rsvd2, bpid, offset),
fields are always 0 anyway;
-S/G format fix for i.MX7 (yes, i.MX7 support was not added yet,
but still...)
Signed-off-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Variable 'ret' is only used for returning the value 0.
We can make it simpler and just return 0 instead.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/returnvar.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In the error paths we should free the resources that were
previously acquired, so fix it accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When doing pointer operation for accessing the HW S/G table,
a value representing number of entries (and not number of bytes)
must be used.
Cc: <stable@vger.kernel.org> # 3.6+
Fixes: 045e36780f ("crypto: caam - ahash hmac support")
Signed-off-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Register only algorithms supported by CAAM hardware, using the CHA
version and instantiation registers to identify hardware capabilities.
Signed-off-by: Victoria Milhoan <vicki.milhoan@freescale.com>
Tested-by: Horia Geantă <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Allow CAAM to be selected in the kernel for Freescale i.MX devices if
ARCH_MXC is enabled.
Signed-off-by: Steve Cornelius <steve.cornelius@freescale.com>
Signed-off-by: Victoria Milhoan <vicki.milhoan@freescale.com>
Tested-by: Horia Geantă <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Avoid moving the head of the scatterlist entry by using temporary
pointers to walk the scatterlist.
Signed-off-by: Victoria Milhoan <vicki.milhoan@freescale.com>
Tested-by: Horia Geantă <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Since fields must be ORed in to operate correctly using any order of
operations, changed allocations of the combination of extended
descriptor structs + hardware scatterlists to use kzalloc() instead
of kmalloc(), so as to ensure that residue data would not be ORed in
with the correct data.
Signed-off-by: Steve Cornelius <steve.cornelius@freescale.com>
Signed-off-by: Victoria Milhoan <vicki.milhoan@freescale.com>
Tested-by: Horia Geantă <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Modify the Scatter-Gather entry definitions for the Freescale
CAAM driver to include support for both 64- and 32-bit DMA pointers.
Signed-off-by: Victoria Milhoan <vicki.milhoan@freescale.com>
Tested-by: Horia Geantă <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
ARM-based systems may disable clocking to the CAAM device on the
Freescale i.MX platform for power management purposes. This patch
enables the required clocks when the CAAM module is initialized and
disables the required clocks when the CAAM module is shut down.
Signed-off-by: Victoria Milhoan <vicki.milhoan@freescale.com>
Tested-by: Horia Geantă <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add set/clear 32-bit primitives for compatibility with ARM devices since
the primitives were previously only defined for the Power architecture.
Signed-off-by: Victoria Milhoan <vicki.milhoan@freescale.com>
Tested-by: Horia Geantă <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Freescale i.MX6 ARM platforms do not support hardware cache coherency.
This patch adds cache coherency support to the CAAM driver.
Signed-off-by: Victoria Milhoan <vicki.milhoan@freescale.com>
Tested-by: Horia Geantă <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch converts the authenc implementations in caam to the
new AEAD interface. The biggest change is that seqiv no longer
generates a random IV. Instead the IPsec sequence number is used
as the IV.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The encap shared descriptor was changed to use the new IV convention.
In the process some commands were shifted, making the output length
zero, caam effectively writing garbage in dst.
While here, update the decap descriptor to execute the "write" commands
before the "read"s (as it previously was).
This makes sure the input fifo is drained before becoming full.
Fixes: 46218750d5 ("crypto: caam - Use new IV convention")
Signed-off-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
An implicit truncation is done when using a variable of 64 bits
in MATH command:
warning: large integer implicitly truncated to unsigned type [-Woverflow]
Silence the compiler by feeding it with an explicit truncated value.
Signed-off-by: Tudor Ambarus <tudor.ambarus@freescale.com>
Signed-off-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When successful, the descriptor that performs RNG initialization
is allowed to return a status code of 7000_0000h, since last command
in the descriptor is a JUMP HALT.
Signed-off-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
HW coherency won't work properly for CAAM write transactions
if AWCACHE is left to default (POR) value - 4'b0001.
It has to be programmed to 4'b0010, i.e. AXI3 Cacheable bit set.
For platforms that have HW coherency support:
-PPC-based: the update has no effect; CAAM coherency already works
due to the IOMMU (PAMU) driver setting the correct memory coherency
attributes
-ARM-based: the update fixes cache coherency issues,
since IOMMU (SMMU) driver is not programmed to behave similar to PAMU
Signed-off-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In order to ensure that the ERA property is properly read from DT
on all platforms, of_property_read* function needs to be used.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Horia Geant? <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch converts rfc4106 to the new calling convention where
the IV is now part of the AD and needs to be skipped.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull crypto update from Herbert Xu:
"Here is the crypto update for 4.2:
API:
- Convert RNG interface to new style.
- New AEAD interface with one SG list for AD and plain/cipher text.
All external AEAD users have been converted.
- New asymmetric key interface (akcipher).
Algorithms:
- Chacha20, Poly1305 and RFC7539 support.
- New RSA implementation.
- Jitter RNG.
- DRBG is now seeded with both /dev/random and Jitter RNG. If kernel
pool isn't ready then DRBG will be reseeded when it is.
- DRBG is now the default crypto API RNG, replacing krng.
- 842 compression (previously part of powerpc nx driver).
Drivers:
- Accelerated SHA-512 for arm64.
- New Marvell CESA driver that supports DMA and more algorithms.
- Updated powerpc nx 842 support.
- Added support for SEC1 hardware to talitos"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (292 commits)
crypto: marvell/cesa - remove COMPILE_TEST dependency
crypto: algif_aead - Temporarily disable all AEAD algorithms
crypto: af_alg - Forbid the use internal algorithms
crypto: echainiv - Only hold RNG during initialisation
crypto: seqiv - Add compatibility support without RNG
crypto: eseqiv - Offer normal cipher functionality without RNG
crypto: chainiv - Offer normal cipher functionality without RNG
crypto: user - Add CRYPTO_MSG_DELRNG
crypto: user - Move cryptouser.h to uapi
crypto: rng - Do not free default RNG when it becomes unused
crypto: skcipher - Allow givencrypt to be NULL
crypto: sahara - propagate the error on clk_disable_unprepare() failure
crypto: rsa - fix invalid select for AKCIPHER
crypto: picoxcell - Update to the current clk API
crypto: nx - Check for bogus firmware properties
crypto: marvell/cesa - add DT bindings documentation
crypto: marvell/cesa - add support for Kirkwood and Dove SoCs
crypto: marvell/cesa - add support for Orion SoCs
crypto: marvell/cesa - add allhwsupport module parameter
crypto: marvell/cesa - add support for all armada SoCs
...
The new aead_edesc_alloc left out the bit indicating the last
entry on the source SG list. This patch fixes it.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
I incorrectly removed DESC_MAX_USED_BYTES when enlarging the size
of the shared descriptor buffers, thus making it four times larger
than what is necessary. This patch restores the division by four
calculation.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch fixes a number of problems in crypto driver Kconfig
entries:
1. Select BLKCIPHER instead of BLKCIPHER2. The latter is internal
and should not be used outside of the crypto API itself.
2. Do not select ALGAPI unless you use a legacy type like
CRYPTO_ALG_TYPE_CIPHER.
3. Select the algorithm type that you are implementing, e.g., AEAD.
4. Do not select generic C code such as CBC/ECB unless you use them
as a fallback.
5. Remove default n since that is the default default.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The patch
crypto: caam - Add definition of rd/wr_reg64 for little endian platform
added support for little endian platforms to the CAAM driver. Namely a
write and read function for 64 bit registers.
The only user of this functions is the Job Ring driver (drivers/crypto/caam/jr.c).
It uses the functions to set the DMA addresses for the input/output rings.
However, at least in the default configuration, the least significant 32 bits are
always in the base+0x0004 address; independent of the endianness of the bytes itself.
That means the addresses do not change with the system endianness.
DMA addresses are only 32 bits wide on non-64-bit systems, writing the upper 32 bits
of this value to the register for the least significant bits results in the DMA address
being set to 0.
Fix this by always writing the registers in the same way.
Suggested-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch converts the caam GCM implementations to the new AEAD
interface. This is compile-tested only.
Note that all IV generation for GCM algorithms have been removed.
The reason is that the current generation uses purely random IVs
which is not appropriate for counter-based algorithms where we
first and foremost require uniqueness.
Of course there is no reason why you couldn't implement seqiv or
seqniv within caam since all they do is xor the sequence number
with a salt, but since I can't test this on actual hardware I'll
leave it alone for now.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently dma_map_sg_chained does not handle errors from the
underlying dma_map_sg calls. This patch adds rollback in case
of an error by simply calling dma_unmap_sg_chained for the ones
that we've already mapped.
All current callers ignore the return value so this should have
no impact on them.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix a "Trying to vfree() nonexistent vm area" error when unloading the CAAM
controller module by providing the correct pointer value to iounmap().
Signed-off-by: Victoria Milhoan <vicki.milhoan@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The CAAM driver uses two data buffers to store data for a hashing operation,
with one buffer defined as active. This change forces switching of the
active buffer when executing a hashing operation to avoid a later DMA unmap
using the length of the opposite buffer.
Signed-off-by: Victoria Milhoan <vicki.milhoan@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The hwrng output buffers (2) are cast inside of a a struct (caam_rng_ctx)
allocated in one DMA-tagged region. While the kernel's heap allocator
should place the overall struct on a cacheline aligned boundary, the 2
buffers contained within may not necessarily align. Consenquently, the ends
of unaligned buffers may not fully flush, and if so, stale data will be left
behind, resulting in small repeating patterns.
This fix aligns the buffers inside the struct.
Note that not all of the data inside caam_rng_ctx necessarily needs to be
DMA-tagged, only the buffers themselves require this. However, a fix would
incur the expense of error-handling bloat in the case of allocation failure.
Cc: stable@vger.kernel.org
Signed-off-by: Steve Cornelius <steve.cornelius@freescale.com>
Signed-off-by: Victoria Milhoan <vicki.milhoan@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently caam assumes that the SG list contains exactly the number
of bytes required. This assumption is incorrect.
Up until now this has been harmless. However with the new AEAD
interface this now breaks as the AD SG list contains more bytes
than just the AD.
This patch fixes this by always clamping the AD SG list by the
specified AD length.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
crt_aead is an internal implementation detail and must not be
used outside of the crypto API itself. This patch replaces the
unnecessary uses of crt_aead with crypto_aead_ivsize.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The caam driver includes algorithm types that it doesn't even
use, such as struct rng_alg which has recently been moved to an
internal header file and consequently broke the build of caam.
This patch removes these bogus references.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
irq_dispose_mapping is not called on all error paths from caam_jr_init.
This takes care of several clean-up issues by performing resource
clean-up and allocation at the same level.
Signed-off-by: Cristian Stoica <cristian.stoica@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
- assoc_nents and src_nents are never zero when all_contig is false
- iv_contig is zero on the else branch
Signed-off-by: Cristian Stoica <cristian.stoica@freescale.com>
Reviewed-by: Richard Schmitt <richard.schmitt@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
ICV check failures are part of normal operation;
leave user notification up to the higher levels,
as is done in s/w algorithm implementations.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Tested-by: Cristian Stoica <cristian.stoica@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Modify crypto drivers to use the generic SG helper since
both of them are equivalent and the one from crypto is redundant.
See also:
468577abe3 reverted in
b2ab4a57b0
Signed-off-by: Cristian Stoica <cristian.stoica@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Pull crypto update from Herbert Xu:
- The crypto API is now documented :)
- Disallow arbitrary module loading through crypto API.
- Allow get request with empty driver name through crypto_user.
- Allow speed testing of arbitrary hash functions.
- Add caam support for ctr(aes), gcm(aes) and their derivatives.
- nx now supports concurrent hashing properly.
- Add sahara support for SHA1/256.
- Add ARM64 version of CRC32.
- Misc fixes.
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (77 commits)
crypto: tcrypt - Allow speed testing of arbitrary hash functions
crypto: af_alg - add user space interface for AEAD
crypto: qat - fix problem with coalescing enable logic
crypto: sahara - add support for SHA1/256
crypto: sahara - replace tasklets with kthread
crypto: sahara - add support for i.MX53
crypto: sahara - fix spinlock initialization
crypto: arm - replace memset by memzero_explicit
crypto: powerpc - replace memset by memzero_explicit
crypto: sha - replace memset by memzero_explicit
crypto: sparc - replace memset by memzero_explicit
crypto: algif_skcipher - initialize upon init request
crypto: algif_skcipher - removed unneeded code
crypto: algif_skcipher - Fixed blocking recvmsg
crypto: drbg - use memzero_explicit() for clearing sensitive data
crypto: drbg - use MODULE_ALIAS_CRYPTO
crypto: include crypto- module prefix in template
crypto: user - add MODULE_ALIAS
crypto: sha-mb - remove a bogus NULL check
crytpo: qat - Fix 64 bytes requests
...
Recently lockless_dereference() was added which can be used in place of
hard-coding smp_read_barrier_depends(). The following PATCH makes the change.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Reviewed-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Merge DES Cipher Block Chaining mode (CBC) and Triple DES Cipher Block
Chaining mode (CBC) algorithms from ablkcipher to givencrypt.
Signed-off-by: Catalin Vasile <catalin.vasile@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The error code returned by hardware is four bits wide with an expected
zero MSB. A hardware error condition where the error code can get between
0x8 and 0xf will trigger an out of bound array access on the error
message table.
This patch fixes the invalid array access following such an error and
reports the condition.
Signed-off-by: Cristian Stoica <cristian.stoica@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for one-shot givencrypt algorithms.
Givencrypt algorithms will generate their IV and encrypt data
within the same shared job descriptors.
Current algorithms merged from ablkcipher to givencrypt are:
- AES Cipher Block Chaining (CBC)
- AES Counter Mode (CTR) compliant with RFC3686
Signed-off-by: Catalin Vasile <catalin.vasile@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for AES Counter Mode (CTR) compliant with RFC3686 to be
used along with authenc algorithms (md5, sha1, sha224, sha256, sha384,
sha512) as one-shot aead algorithms.
Signed-off-by: Catalin Vasile <catalin.vasile@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for Advanced Encryption Standard (AES) in Counter Mode (CTR)
as provided in IPsec implementation standard RFC3686.
ablkcipher shared descriptors now save context registers after job
execution. This is used to load Nonce specific to RFC3686 only at
first execution of shared job descriptor.
Signed-off-by: Catalin Vasile <catalin.vasile@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for AES working in Counter Mode
Signed-off-by: Catalin Vasile <catalin.vasile@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add AES-GMAC as an IPSec ESP mechanism to provide
data origin authentication, but not confidentiality.
This method is referred as ENCR_NULL_AUTH_AES_GMAC.
Signed-off-by: Tudor Ambarus <tudor.ambarus@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch fixes the assumption that output sequence is not contiguous
when input sequence is not contiguous and in-place encryption is done.
Output sequence does not need to be contiguous with associated data.
Signed-off-by: Tudor Ambarus <tudor.ambarus@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If dma mapping for dma_addr_out fails, the descriptor memory is freed
but the previous dma mapping for dma_addr_in remains.
This patch resolves the missing dma unmap and groups resource
allocations at function start.
Cc: <stable@vger.kernel.org> # 3.13+
Signed-off-by: Cristian Stoica <cristian.stoica@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add Advanced Encryption Standard (AES) in Galois/Counter Mode (GCM)
as an IPsec Encapsulating Security Payload (ESP) mechanism
to provide confidentiality and data origin authentication.
Signed-off-by: Tudor Ambarus <tudor.ambarus@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for AES working in Galois Counter Mode.
There is a limitation related to IV size, similar to the one present in
SW implementation (crypto/gcm.c):
The only IV size allowed is 12 bytes. It will be padded by HW to the right
with 0x0000_0001 (up to 16 bytes - AES block size), according to the GCM
specification.
Signed-off-by: Tudor Ambarus <tudor.ambarus@freescale.com>
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
CAAM's memory is broken into following address blocks:
Block Included Registers
0 General Registers
1-4 Job ring registers
6 RTIC registers
7 QI registers
8 DECO and CCB
Size of the above stated blocks varies in various platforms. The block size can be 4K or 64K.
The block size can be dynamically determined by reading CTPR register in CAAM.
This patch initializes the block addresses dynamically based on the value read from this register.
Signed-off-by: Ruchika Gupta <r66431@freescale.com>
Signed-off-by: Nitesh Narayan Lal <b44382@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
buf_0 and buf_1 in caam_hash_state are not next to each other.
Accessing buf_1 is incorrect from &buf_0 with an offset of only
size_of(buf_0). The same issue is also with buflen_0 and buflen_1
Cc: <stable@vger.kernel.org> # 3.13+
Signed-off-by: Cristian Stoica <cristian.stoica@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The sampling of the oscillator can be done in multiple modes for
generating the entropy value. By default, this is set to von
Neumann. This patch changes the sampling to raw data, since it
has been discovered that the generated entropy has a better
'quality'.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The entropy delay (the length in system clocks of each
entropy sample) for the RNG4 block of CAAM is dependent
on the frequency of the SoC. By elaborate methods, it
has been determined that a good starting value for all
platforms integrating the CAAM IP is 3200. Using a
higher value has additional benefit of speeding up
the process of instantiating the RNG, since the entropy
delay will be increased and instantiation of the RNG
state handles will be reattempted by the driver. If the
starting value is low, for certain platforms, this can
lead to a quite lengthy process.
This patch changes the starting value of the length of
the entropy sample to 3200 system clocks.
In addition to this change, the attempted entropy delay
values are now printed on the console upon initialization
of the RNG block.
While here, a safeguard for yielding the processor was
added for ensuring that in very adverse cases,
the CPU isn't hogged by the instantiation loop.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The rtfrqmax & rtfrqmin set the bounds of the expected frequency of the
oscillator, when SEC runs at its maximum frequency. For certain platforms
(f.i. T2080), the oscillator is very fast and thus if the SEC runs at
a lower than normal frequency, the ring oscillator is incorrectly detected
as being out of bounds.
This patch effectively disables the maximum frequency check, by setting a
high enough maximum allowable frequency for the oscillator. The reasoning
behind this is that usually a broken oscillator will run too slow
(i.e. not run at all) rather than run too fast.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull crypto update from Herbert Xu:
- CTR(AES) optimisation on x86_64 using "by8" AVX.
- arm64 support to ccp
- Intel QAT crypto driver
- Qualcomm crypto engine driver
- x86-64 assembly optimisation for 3DES
- CTR(3DES) speed test
- move FIPS panic from module.c so that it only triggers on crypto
modules
- SP800-90A Deterministic Random Bit Generator (drbg).
- more test vectors for ghash.
- tweak self tests to catch partial block bugs.
- misc fixes.
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (94 commits)
crypto: drbg - fix failure of generating multiple of 2**16 bytes
crypto: ccp - Do not sign extend input data to CCP
crypto: testmgr - add missing spaces to drbg error strings
crypto: atmel-tdes - Switch to managed version of kzalloc
crypto: atmel-sha - Switch to managed version of kzalloc
crypto: testmgr - use chunks smaller than algo block size in chunk tests
crypto: qat - Fixed SKU1 dev issue
crypto: qat - Use hweight for bit counting
crypto: qat - Updated print outputs
crypto: qat - change ae_num to ae_id
crypto: qat - change slice->regions to slice->region
crypto: qat - use min_t macro
crypto: qat - remove unnecessary parentheses
crypto: qat - remove unneeded header
crypto: qat - checkpatch blank lines
crypto: qat - remove unnecessary return codes
crypto: Resolve shadow warnings
crypto: ccp - Remove "select OF" from Kconfig
crypto: caam - fix DECO RSR polling
crypto: qce - Let 'DEV_QCE' depend on both HAS_DMA and HAS_IOMEM
...
RSR (Request Source Register) is not used when
virtualization is disabled, thus don't poll for Valid bit.
Besides this, if used, timeout has to be reinitialized.
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
AES currently shares descriptor creation functions with DES and 3DES.
DK bit is set in all cases, however it is valid only for
the AES accelerator.
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Horia Geantă