When the BT connection is initiated by headset, it's possible that headset
requests to make one A2DP and one Voice connection over the same link.
BT firmware will send a new profile A2DP_Voice in this case. So WLAN
has to take care of this new profile for tuning BTCOEX parameters.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The simulataneous transmission of both WLAN and BT might cause
increase in power levels. To avoid regulatory violation, WLAN tx
power will be adjusted according to BT power index based on avaliability
of BT scheduling messages. WLAN tx power reduction might affect its
performance. So WLAN tx power is only be lowered when the signal strength
is good enough. Otherwise concurrent tx will be disabled and WLAN uses
it default power levels. Also concurrent tx is disabled whenever WLAN is
moving to off-channel which might be used by BT.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This feature enables both WLAN and BT can transmit simultaneously
by setting WLAN and BT to equal priorities. Whenever both are
transmitting, it might violate regulatory power limits. To avoid
regulatory violation, WLAN tx power will be adjusted according to BT
power index based on avaliability of BT scheduling message. If the
combined power exceeds threshold, BT transmission will be held off.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WLAN updates channel bitmap when associated and disassociated. Channel
bitmap will reflect whare are the channels used or affected by WLAN and
BT should avoid using those. Not doing so, could affect BT traffic
as both WLAN and BT is operating on same channel.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MCI interrupts have to be enabled only when BTCOEX is
actually in use.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves all the MCI-specific declarations that have been
dumped unceremoniously in hw.h to ar9003_mci.h
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
required buffers and dma allocation is done for GPM and SCHED
messages
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9462 chips have the capabilities to provoide bluetooth
profile information. For non-AR9462 btcoex chips, the BT
priority traffic was identified by periodically polling
the respective registers and updated dutycycle, stomptype,
etc. As AR9462 chip offers the BT profile informations,
let us make use of that to update aggregation limit,
dutycycle, stomptype and wieghtages.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan