The size of array 'priv->ports[]' is INNO_PHY_PORT_NUM.
In the for loop, 'i' is used as the index for array 'priv->ports[]'
with a check (i > INNO_PHY_PORT_NUM) which indicates that
INNO_PHY_PORT_NUM is allowed value for 'i' in the same loop.
This > comparison needs to be changed to >=, otherwise it potentially leads
to an out of bounds write on the next iteration through the loop
Fixes: ba8b0ee81f ("phy: add inno-usb2-phy driver for hi3798cv200 SoC")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Link: https://lore.kernel.org/r/20230721090558.3588613-1-harshit.m.mogalapalli@oracle.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The return value from qcom_snps_hsphy_suspend/resume is not used. Make
sure qcom_snps_hsphy_runtime_suspend/resume return this value as well.
Signed-off-by: Adrien Thierry <athierry@redhat.com>
Link: https://lore.kernel.org/r/20230629144542.14906-4-athierry@redhat.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver is not enabling the ref clock, which thus gets disabled by
the clk_disable_unused() initcall. This leads to the dwc3 controller
failing to initialize if probed after clk_disable_unused() is called,
for instance when the driver is built as a module.
To fix this, switch to the clk_bulk API to handle both cfg_ahb and ref
clocks at the proper places.
Note that the cfg_ahb clock is currently not used by any device tree
instantiation of the PHY. Work needs to be done separately to fix this.
Link: https://lore.kernel.org/linux-arm-msm/ZEqvy+khHeTkC2hf@fedora/
Fixes: 51e8114f80 ("phy: qcom-snps: Add SNPS USB PHY driver for QCOM based SOCs")
Signed-off-by: Adrien Thierry <athierry@redhat.com>
Link: https://lore.kernel.org/r/20230629144542.14906-3-athierry@redhat.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In the dwc3 core, both system and runtime suspend end up calling
dwc3_suspend_common(). From there, what happens for the PHYs depends on
the USB mode and whether the controller is entering system or runtime
suspend.
HOST mode:
(1) system suspend on a non-wakeup-capable controller
The [1] if branch is taken. dwc3_core_exit() is called, which ends up
calling phy_power_off() and phy_exit(). Those two functions decrease the
PM runtime count at some point, so they will trigger the PHY runtime
sleep (assuming the count is right).
(2) runtime suspend / system suspend on a wakeup-capable controller
The [1] branch is not taken. dwc3_suspend_common() calls
phy_pm_runtime_put_sync(). Assuming the ref count is right, the PHY
runtime suspend op is called.
DEVICE mode:
dwc3_core_exit() is called on both runtime and system sleep
unless the controller is already runtime suspended.
OTG mode:
(1) system suspend : dwc3_core_exit() is called
(2) runtime suspend : do nothing
In host mode, the code seems to make a distinction between 1) runtime
sleep / system sleep for wakeup-capable controller, and 2) system sleep
for non-wakeup-capable controller, where phy_power_off() and phy_exit()
are only called for the latter. This suggests the PHY is not supposed to
be in a fully powered-off state for runtime sleep and system sleep for
wakeup-capable controller.
Moreover, downstream, cfg_ahb_clk only gets disabled for system suspend.
The clocks are disabled by phy->set_suspend() [2] which is only called
in the system sleep path through dwc3_core_exit() [3].
With that in mind, don't disable the clocks during the femto PHY runtime
suspend callback. The clocks will only be disabled during system suspend
for non-wakeup-capable controllers, through dwc3_core_exit().
[1] https://elixir.bootlin.com/linux/v6.4/source/drivers/usb/dwc3/core.c#L1988
[2] https://git.codelinaro.org/clo/la/kernel/msm-5.4/-/blob/LV.AU.1.2.1.r2-05300-gen3meta.0/drivers/usb/phy/phy-msm-snps-hs.c#L524
[3] https://git.codelinaro.org/clo/la/kernel/msm-5.4/-/blob/LV.AU.1.2.1.r2-05300-gen3meta.0/drivers/usb/dwc3/core.c#L1915
Signed-off-by: Adrien Thierry <athierry@redhat.com>
Link: https://lore.kernel.org/r/20230629144542.14906-2-athierry@redhat.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The pll prediv calculus searchs for the smallest prediv that gets
the ns_hdmipll_ck in the range of 5 GHz to 12 GHz.
A typo in the upper bound test was testing for 5Ghz to 1Ghz
Fixes: 45810d486b ("phy: mediatek: add support for phy-mtk-hdmi-mt8195")
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230529-hdmi_phy_fix-v1-1-bf65f53af533@baylibre.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
- New Support
- Debugfs support for phy core and mediatek driver
- Hisilicon inno-usb2-phy driver supporting Hi3798MV100
- Qualcomm SGMII SerDes PHY driver, SM6115 & QCM2290 QMP-USB support,
SA8775P USB PHY & USB3 UNI support, QUSB2 support for IPQ9574, IPQ9574 USB3 PHY
- Updates
- Sparx5 serdes phy power optimzation
- cadence salvo usb properties and updates and torrent DP with PCIe &
USB support
- Yaml conversion for Broadcom kona USB bindings and MXS USB binding
-----BEGIN PGP SIGNATURE-----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=ReXo
-----END PGP SIGNATURE-----
Merge tag 'phy-for-6.5_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull phy updates from Vinod Koul:
"New Support:
- Debugfs support for phy core and mediatek driver
- Hisilicon inno-usb2-phy driver supporting Hi3798MV100
- Qualcomm SGMII SerDes PHY driver, SM6115 & QCM2290 QMP-USB support,
SA8775P USB PHY & USB3 UNI support, QUSB2 support for IPQ9574,
IPQ9574 USB3 PHY
UpdatesL
- Sparx5 serdes phy power optimzation
- cadence salvo usb properties and updates and torrent DP with PCIe &
USB support
- Yaml conversion for Broadcom kona USB bindings and MXS USB binding"
* tag 'phy-for-6.5_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (67 commits)
dt-bindings: phy: brcm,brcmstb-usb-phy: Fix error in "compatible" conditional schema
dt-bindings: phy: mixel,mipi-dsi-phy: Remove assigned-clock* properties
dt-bindings: phy: intel,combo-phy: restrict node name suffixes
dt-bindings: phy: qcom,usb-hs-phy: Add compatible
phy: tegra: xusb: check return value of devm_kzalloc()
phy: qcom: qmp-combo: fix Display Port PHY configuration for SM8550
phy: qcom: add the SGMII SerDes PHY driver
dt-bindings: phy: describe the Qualcomm SGMII PHY
phy: qualcomm: fix indentation in Makefile
phy: usb: suppress OC condition for 7439b2
phy: usb: Turn off phy when port is in suspend
phy: tegra: xusb: Clear the driver reference in usb-phy dev
dt-bindings: phy: mxs-usb-phy: add imx8ulp and imx8qm compatible
dt-bindings: phy: mxs-usb-phy: convert to DT schema format
dt-bindings: phy: qcom,qmp-usb: fix bindings error
dt-bindings: phy: qcom,qmp-ufs: fix the sc8180x regs
dt-bindings: phy: qcom,qmp-pcie: fix the sc8180x regs
phy: mediatek: tphy: add debugfs files
phy: core: add debugfs files
phy: fsl-imx8mp-usb: add support for phy tuning
...
-----BEGIN PGP SIGNATURE-----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=YwIy
-----END PGP SIGNATURE-----
Merge tag 'media/v6.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Lots of improvement at atomisp driver, which is starting to look in
good shape
- Mediatek vcodec driver has gained support for av1 and hevc stateless
codecs
- New sensor driver: ov01a10
- verisilicon driver has gained AV1 entropy helpers
- tegra-video has gained support for Tegra20 parallel input
- dvb core has gained an extra property to better support DVB-S2X
- as usual, lots of cleanups, fixes and improvements on media drivers
* tag 'media/v6.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (253 commits)
media: wl128x: fix a clang warning
media: dvb: mb86a20s: get rid of a clang-15 warning
media: cec: i2c: ch7322: also select REGMAP
media: add HAS_IOPORT dependencies
media: tc358746: select CONFIG_GENERIC_PHY
media: mediatek: vcodec: Add dbgfs help function
media: mediatek: vcodec: Add encode to support dbgfs
media: mediatek: vcodec: Change dbgfs interface to support encode
media: mediatek: vcodec: Get each instance format type
media: mediatek: vcodec: Get each context resolution information
media: mediatek: vcodec: Add a debugfs file to get different useful information
media: mediatek: vcodec: Add debug params to control different log level
media: mediatek: vcodec: Add debugfs interface to get debug information
media: mediatek: vcodec: support stateless AV1 decoder
media: verisilicon: Conditionally ignore native formats
media: verisilicon: Enable AV1 decoder on rk3588
media: verisilicon: Add film grain feature to AV1 driver
media: verisilicon: Add Rockchip AV1 decoder
media: verisilicon: Add AV1 entropy helpers
media: verisilicon: Compute motion vectors size for AV1 frames
...
SoC support. Instead there's a treewide patch series from Maxime that makes
clk_ops::determine_rate mandatory for muxes. Beyond that core framework change
we have the usual pile of clk driver updates such as migrating i2c drivers to
use .probe() again or YAMLfication of clk DT bindings so we can validate DTBs.
Overall the SoCs that got the most updates this time around in terms of
diffstat are the Amlogic and Mediatek drivers because they added new SoC
support or fixed up various drivers to have proper data.
In general things look kinda quiet. I suspect the core framework change may
still shake out some problems after the merge window, mostly because not
everyone tests linux-next where that series has been for some number of weeks.
I saw that there's at least one pending fix for Tegra that needs to be wrapped
up into a proper patch. I'll try to catch those bits before the window closes
so that -rc1 is bootable. More details below.
Core:
- Make clk_ops::determine_rate mandatory for muxes
New Drivers:
- Add amlogic a1 SoC family PLL and peripheral clock controller support
Updates:
- Handle allocation failures from kasprintf() and friends
- Migrate platform clk drivers to .remove_new()
- Migrate i2c clk drivers to .probe() instead of .probe_new()
- Remove CLK_SET_PARENT from all Mediatek MSDC core clocks
- Add infra_ao reset support for Mediatek MT8188 SoCs
- Align driver_data to i2c_device_id tables in some i2c clk drivers
- Use device_get_match_data() in vc5 clk driver
- New Kconfig symbol name (SOC_MICROCHIP_POLARFIRE) for Microchip FPGA clock
drivers
- Use of_property_read_bool() to read "microchip,pic32mzda-sosc" boolean DT
property in clk-pic32mzda
- Convert AT91 clock dt-bindings to YAML
- Remove CLK_SET_RATE_PARENT flag from LDB clocks on i.MX6SX
- Keep i.MX UART clocks enabled during kernel boot if earlycon is set
- Drop imx_unregister_clocks() as there are no users anymore
- Switch to _safe iterator on imx_clk_scu_unregister() to avoid use after free
- Add determine_rate op to the imx8m composite clock
- Use device managed API for iomap and kzalloc for i.MXRT1050, i.MX8MN,
i.MX8MP and i.MX93 clock controller drivers
- Add missing interrupt DT property for the i.MX8M clock controller
- Re-add support for Exynos4212 clock controller because we are
re-introducing the SoC in the mainline
- Add CONFIG_OF dependency to Samsung clk Kconfig symbols to solve some
objtool warnings
- Preselect PLL MIPI as TCON0 parent for Allwinner A64 SoC
- Convert the Renesas clock drivers to readl_poll_timeout_atomic()
- Add PWM clock on Renesas R-Car V3U
- Fix PLL5 on Renesas RZ/G2L and RZ/V2L
-----BEGIN PGP SIGNATURE-----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=6M8D
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This batch of clk driver updates contains almost no new SoC support.
Instead there's a treewide patch series from Maxime that makes
clk_ops::determine_rate mandatory for muxes.
Beyond that core framework change we have the usual pile of clk driver
updates such as migrating i2c drivers to use .probe() again or
YAMLfication of clk DT bindings so we can validate DTBs.
Overall the SoCs that got the most updates this time around in terms
of diffstat are the Amlogic and Mediatek drivers because they added
new SoC support or fixed up various drivers to have proper data.
In general things look kinda quiet. I suspect the core framework
change may still shake out some problems after the merge window,
mostly because not everyone tests linux-next where that series has
been for some number of weeks. I saw that there's at least one pending
fix for Tegra that needs to be wrapped up into a proper patch. I'll
try to catch those bits before the window closes so that -rc1 is
bootable. More details below.
Core:
- Make clk_ops::determine_rate mandatory for muxes
New Drivers:
- Add amlogic a1 SoC family PLL and peripheral clock controller support
Updates:
- Handle allocation failures from kasprintf() and friends
- Migrate platform clk drivers to .remove_new()
- Migrate i2c clk drivers to .probe() instead of .probe_new()
- Remove CLK_SET_PARENT from all Mediatek MSDC core clocks
- Add infra_ao reset support for Mediatek MT8188 SoCs
- Align driver_data to i2c_device_id tables in some i2c clk drivers
- Use device_get_match_data() in vc5 clk driver
- New Kconfig symbol name (SOC_MICROCHIP_POLARFIRE) for Microchip
FPGA clock drivers
- Use of_property_read_bool() to read "microchip,pic32mzda-sosc"
boolean DT property in clk-pic32mzda
- Convert AT91 clock dt-bindings to YAML
- Remove CLK_SET_RATE_PARENT flag from LDB clocks on i.MX6SX
- Keep i.MX UART clocks enabled during kernel boot if earlycon is set
- Drop imx_unregister_clocks() as there are no users anymore
- Switch to _safe iterator on imx_clk_scu_unregister() to avoid use
after free
- Add determine_rate op to the imx8m composite clock
- Use device managed API for iomap and kzalloc for i.MXRT1050,
i.MX8MN, i.MX8MP and i.MX93 clock controller drivers
- Add missing interrupt DT property for the i.MX8M clock controller
- Re-add support for Exynos4212 clock controller because we are
re-introducing the SoC in the mainline
- Add CONFIG_OF dependency to Samsung clk Kconfig symbols to solve
some objtool warnings
- Preselect PLL MIPI as TCON0 parent for Allwinner A64 SoC
- Convert the Renesas clock drivers to readl_poll_timeout_atomic()
- Add PWM clock on Renesas R-Car V3U
- Fix PLL5 on Renesas RZ/G2L and RZ/V2L"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (149 commits)
clk: fix typo in clk_hw_register_fixed_rate_parent_data() macro
clk: Fix memory leak in devm_clk_notifier_register()
clk: mvebu: Iterate over possible CPUs instead of DT CPU nodes
clk: mvebu: Use of_get_cpu_hwid() to read CPU ID
MAINTAINERS: Add Marvell mvebu clock drivers
clk: clocking-wizard: check return value of devm_kasprintf()
clk: ti: clkctrl: check return value of kasprintf()
clk: keystone: sci-clk: check return value of kasprintf()
clk: si5341: free unused memory on probe failure
clk: si5341: check return value of {devm_}kasprintf()
clk: si5341: return error if one synth clock registration fails
clk: cdce925: check return value of kasprintf()
clk: vc5: check memory returned by kasprintf()
clk: mediatek: clk-mt8173-apmixedsys: Fix iomap not released issue
clk: mediatek: clk-mt8173-apmixedsys: Fix return value for of_iomap() error
clk: mediatek: clk-mtk: Grab iomem pointer for divider clocks
clk: keystone: syscon-clk: Add support for audio refclk
dt-bindings: clock: Add binding documentation for TI Audio REFCLK
dt-bindings: clock: ehrpwm: Remove unneeded syscon compatible
clk: keystone: syscon-clk: Allow the clock node to not be of type syscon
...
The tc358746 driver selects CONFIG_GENERIC_PHY_MIPI_DPHY and links to
that, but this fails when CONFIG_GENERIC_PHY is disabled, because Kbuild
then never enters the drivers/phy directory for building object files:
ERROR: modpost: "phy_mipi_dphy_get_default_config_for_hsclk" [drivers/media/i2c/tc358746.ko] undefined!
Add an explicit 'select GENERIC_PHY' here to ensure that the directory
is entered, and add another dependency on that symbol so make it
more obvious what is going on if another driver has the same problem,
as this will produce a Kconfig warning.
Link: https://lore.kernel.org/linux-media/20230623152318.2276816-1-arnd@kernel.org
Fixes: 80a21da360 ("media: tc358746: add Toshiba TC358746 Parallel to CSI-2 bridge driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The SM8550 PHY also uses a different offset for the CMN_STATUS reg,
use the right one for the v6 Display Port configuration.
Fixes: 49742e9eda ("phy: qcom-qmp-combo: Add support for SM8550")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230601-topic-sm8550-upstream-dp-phy-init-fix-v1-1-4e9da9f97991@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Implement support for the SGMII/SerDes PHY present on various Qualcomm
platforms.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20230619091336.194914-4-brgl@bgdev.pl
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We hit a false positive OC for 7439b2 in DRD/device mode for the
second port. So disable the OC check for this use case. Add capability
to suppress OC condition for specific ports.
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/1686859578-45242-3-git-send-email-justin.chen@broadcom.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The COMMONONN bit turns off the PHY when the host controller puts it
into suspend state. This can happen during the following...
- Nothing is connected to the port
- The host controller goes into low power mode whatever due to auto
suspend or system suspend.
With COMMONONN we also must unset U2_FREECLK_EXISTS since the UTMI
clock is fed by the PHY.
With these changes we see a power savings of ~12mW when port is in
suspend.
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Link: https://lore.kernel.org/r/1686859578-45242-2-git-send-email-justin.chen@broadcom.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For the dual-role port, it will assign the phy dev to usb-phy dev and
use the port dev driver as the dev driver of usb-phy.
When we try to destroy the port dev, it will destroy its dev driver
as well. But we did not remove the reference from usb-phy dev. This
might cause the use-after-free issue in KASAN.
Fixes: e8f7d2f409 ("phy: tegra: xusb: Add usb-phy support")
Cc: stable@vger.kernel.org
Signed-off-by: EJ Hsu <ejh@nvidia.com>
Signed-off-by: Haotien Hsu <haotienh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20230609062932.3276509-1-haotienh@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The TI J721e Wiz clock implements a mux with a set_parent
hook, but doesn't provide a determine_rate implementation.
This is a bit odd, since set_parent() is there to, as its name implies,
change the parent of a clock. However, the most likely candidate to
trigger that parent change is a call to clk_set_rate(), with
determine_rate() figuring out which parent is the best suited for a
given rate.
The other trigger would be a call to clk_set_parent(), but it's far less
used, and it doesn't look like there's any obvious user for that clock.
So, the set_parent hook is effectively unused, possibly because of an
oversight. However, it could also be an explicit decision by the
original author to avoid any reparenting but through an explicit call to
clk_set_parent().
The latter case would be equivalent to setting the flag
CLK_SET_RATE_NO_REPARENT, together with setting our determine_rate hook
to __clk_mux_determine_rate(). Indeed, if no determine_rate
implementation is provided, clk_round_rate() (through
clk_core_round_rate_nolock()) will call itself on the parent if
CLK_SET_RATE_PARENT is set, and will not change the clock rate
otherwise.
And if it was an oversight, then we are at least explicit about our
behavior now and it can be further refined down the line.
Since the CLK_SET_RATE_NO_REPARENT flag was already set though, it seems
unlikely.
Cc: Kishon Vijay Abraham I <kishon@kernel.org>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: linux-phy@lists.infradead.org
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20221018-clk-range-checks-fixes-v4-44-971d5077e7d2@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The TI AM654 SerDes clock implements a mux with a set_parent
hook, but doesn't provide a determine_rate implementation.
This is a bit odd, since set_parent() is there to, as its name implies,
change the parent of a clock. However, the most likely candidate to
trigger that parent change is a call to clk_set_rate(), with
determine_rate() figuring out which parent is the best suited for a
given rate.
The other trigger would be a call to clk_set_parent(), but it's far less
used, and it doesn't look like there's any obvious user for that clock.
So, the set_parent hook is effectively unused, possibly because of an
oversight. However, it could also be an explicit decision by the
original author to avoid any reparenting but through an explicit call to
clk_set_parent().
The latter case would be equivalent to setting the flag
CLK_SET_RATE_NO_REPARENT, together with setting our determine_rate hook
to __clk_mux_determine_rate(). Indeed, if no determine_rate
implementation is provided, clk_round_rate() (through
clk_core_round_rate_nolock()) will call itself on the parent if
CLK_SET_RATE_PARENT is set, and will not change the clock rate
otherwise.
And if it was an oversight, then we are at least explicit about our
behavior now and it can be further refined down the line.
Since the CLK_SET_RATE_NO_REPARENT flag was already set though, it seems
unlikely.
Cc: Kishon Vijay Abraham I <kishon@kernel.org>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: linux-phy@lists.infradead.org
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20221018-clk-range-checks-fixes-v4-43-971d5077e7d2@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The Cadence Torrent refclk clock implements a mux with a set_parent
hook, but doesn't provide a determine_rate implementation.
This is a bit odd, since set_parent() is there to, as its name implies,
change the parent of a clock. However, the most likely candidate to
trigger that parent change is a call to clk_set_rate(), with
determine_rate() figuring out which parent is the best suited for a
given rate.
The other trigger would be a call to clk_set_parent(), but it's far less
used, and it doesn't look like there's any obvious user for that clock.
So, the set_parent hook is effectively unused, possibly because of an
oversight. However, it could also be an explicit decision by the
original author to avoid any reparenting but through an explicit call to
clk_set_parent().
The latter case would be equivalent to setting the flag
CLK_SET_RATE_NO_REPARENT, together with setting our determine_rate hook
to __clk_mux_determine_rate(). Indeed, if no determine_rate
implementation is provided, clk_round_rate() (through
clk_core_round_rate_nolock()) will call itself on the parent if
CLK_SET_RATE_PARENT is set, and will not change the clock rate
otherwise.
And if it was an oversight, then we are at least explicit about our
behavior now and it can be further refined down the line.
Since the CLK_SET_RATE_NO_REPARENT flag was already set though, it seems
unlikely.
Cc: Kishon Vijay Abraham I <kishon@kernel.org>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: linux-phy@lists.infradead.org
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20221018-clk-range-checks-fixes-v4-42-971d5077e7d2@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The Cadence Sierra PLL clock implements a mux with a set_parent hook,
but doesn't provide a determine_rate implementation.
This is a bit odd, since set_parent() is there to, as its name implies,
change the parent of a clock. However, the most likely candidate to
trigger that parent change is a call to clk_set_rate(), with
determine_rate() figuring out which parent is the best suited for a
given rate.
The other trigger would be a call to clk_set_parent(), but it's far less
used, and it doesn't look like there's any obvious user for that clock.
So, the set_parent hook is effectively unused, possibly because of an
oversight. However, it could also be an explicit decision by the
original author to avoid any reparenting but through an explicit call to
clk_set_parent().
The latter case would be equivalent to setting the flag
CLK_SET_RATE_NO_REPARENT, together with setting our determine_rate hook
to __clk_mux_determine_rate(). Indeed, if no determine_rate
implementation is provided, clk_round_rate() (through
clk_core_round_rate_nolock()) will call itself on the parent if
CLK_SET_RATE_PARENT is set, and will not change the clock rate
otherwise.
And if it was an oversight, then we are at least explicit about our
behavior now and it can be further refined down the line.
Since the CLK_SET_RATE_NO_REPARENT flag was already set though, it seems
unlikely.
Cc: Kishon Vijay Abraham I <kishon@kernel.org>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: linux-phy@lists.infradead.org
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20221018-clk-range-checks-fixes-v4-41-971d5077e7d2@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
These debugfs files are mainly used to make eye diagram test easier,
especially helpful to do HQA test for a new IC without efuse enabled.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20230513092218.21139-2-chunfeng.yun@mediatek.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add a debugfs root for phy class, and create a debugfs directory under
the root when create phy, then phy drivers can add debugfs files.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20230513092218.21139-1-chunfeng.yun@mediatek.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add USB PHY parameter tuning for USB certifications.
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
[j.zink: ported to v6.3-rc1 from NXP downstream repo + cleanups]
Signed-off-by: Johannes Zink <j.zink@pengutronix.de>
Link: https://lore.kernel.org/r/20230516-lustige-usb-phy-dinge-v2-2-3383a0de34ac@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The QMP combo PHY sits in an of_graph connected between the DisplayPort
controller and a USB Type-C connector (or possibly a redriver).
The TCPM needs to be able to convey the HPD signal to the DisplayPort
controller, but no directly link is provided by DeviceTree so the signal
needs to "pass through" the QMP combo phy.
Handle this by introducing a drm_bridge which upon initialization finds
the next bridge (i.e. the usb-c-connector) and chain this together. This
way HPD changes in the connector will propagate to the DisplayPort
driver.
The connector bridge is resolved lazily, as the TCPM is expected to be
able to resolve the typec mux and switch at probe time, so the QMP combo
phy will probe before the TCPM.
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Abel Vesa <abel.vesa@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on HDK8450
Tested-by: Johan Hovold <johan+linaro@kernel.org> # X13s
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20230515032743.400170-7-quic_bjorande@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The data lanes of the QMP PHY is swapped in order to handle changing
orientation of the USB Type-C cable. Register a typec_switch device to
allow a TCPM to configure the orientation.
The newly introduced orientation variable is adjusted based on the
request, and the initialized components are brought down and up again.
To keep track of what parts needs to be cycled new variables to keep
track of the individual init_count is introduced.
Both the USB and the DisplayPort altmode signals are properly switched.
For DisplayPort the controller will after the TCPM having established
orientation power on the PHY, so this is not done implicitly, but for
USB the PHY typically is kept initialized across the switch, and must
therefore then be reinitialized.
This is based on initial work by Wesley Cheng.
Link: https://lore.kernel.org/r/20201009082843.28503-3-wcheng@codeaurora.org/
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Abel Vesa <abel.vesa@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on HDK8450
Tested-by: Johan Hovold <johan+linaro@kernel.org> # X13s
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20230515032743.400170-6-quic_bjorande@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In multiple places throughout the driver code has been written in
prepration for handling of orientation switching.
Introduce a typec_orientation in qmp_combo and fill out the various
"placeholders" with the associated logic. By initializing the
orientation to "normal" this change has no functional impact, but
reduces the size of the upcoming introduction of dynamic orientation
switching.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Tested-by: Abel Vesa <abel.vesa@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on HDK8450
Tested-by: Johan Hovold <johan+linaro@kernel.org> # X13s
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20230515032743.400170-5-quic_bjorande@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The phy core ensures mutual exclusion across the ops for a given phy,
but the upcoming introduction of USB Type-C orientation switching might
race with the DisplayPort phy operations. So extend the mutual exclusion
to cover the remaining ops as well, to avoid concurrent reconfiguration
of the hardware.
Reported-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20230515032743.400170-4-quic_bjorande@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
With the upcoming introduction of USB Type-C orientation switching the
region of mutual exclusion needs to be extended to cover both the common
init/exit as well as the individual functions.
So move the phy_mutex one step up the stack.
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Abel Vesa <abel.vesa@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on HDK8450
Tested-by: Johan Hovold <johan+linaro@kernel.org> # X13s
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Link: https://lore.kernel.org/r/20230515032743.400170-3-quic_bjorande@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add cdns,usb2-disconnect-threshold-microvolt property to address fake USB
disconnection issue during enumeration or suspend state for difference
platform.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20230517161646.3418250-6-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For NXP platform design, the PHY can't know VBUS well, it causes the FSM
in controller seeing the disconnection at L1 use case. With .set_mode API
introduced, the controller driver could force PHY seeing B Session VALID
when it is at the device mode (VBUS is there), and keep FSM working well.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20230517161646.3418250-5-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Very limited parts may fail to work on full speed mode (both host and
device modes) for USB3 port due to higher threshold in full speed receiver
of USB2.0 PHY.
One example failure symptom is, the enumeration is failed when connecting
full speed USB mouse to USB3 port, especially under high temperature.
The workaround is to configure threshold voltage value of single ended
receiver by setting USB2.0 PHY register AFE_RX_REG5[2:0] to 3'b101.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20230517161646.3418250-4-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For USB2 L1 use cases, some hosts may start transferring less than 20us
after End of Resume, it causes the host seeing corrupt packet from the
device side. The reason is the delay time between PHY powers up and
txvalid is 20us. To fix it, we change the delay value as 0us.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20230517161646.3418250-3-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There is an offset for USB2PHY in SALVO phy, add offset parameter for read
and write API to cover both USB2 and USB3 PHY control.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20230517161646.3418250-2-Frank.Li@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for the new qcm2290 / sm6115 binding.
The USB QMP phy on these devices supports 2 lanes. Note that the
binding now does not describe every register subregion and instead
the driver holds the corresponding offsets.
While at it also include support for PCS_MISC region which was left
out earlier.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Link: https://lore.kernel.org/r/20230516150511.2346357-3-bhupesh.sharma@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
TI's J784S4 SoC supports USXGMII mode with the CPSW9G instance's MAC
ports 1 and 2. Add USXGMII mode to the extra_modes member of J784S4's
SoC data.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230331062521.529005-3-s-vadapalli@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Each of the CPSW9G ports in TI's J784S4 SoC support modes such as QSGMII.
Add a new compatible for it and allow the usage of "ti,qsgmii-main-ports"
property for J784S4.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230331062521.529005-2-s-vadapalli@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
TI's J721E SoC supports SGMII mode with the CPSW9G instance of the CPSW
Ethernet Switch. Thus, enable it by adding SGMII mode to the list of the
corresponding extra_modes member.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230309063514.398705-4-s-vadapalli@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
TI's J7200 SoC supports SGMII mode with the CPSW5G instance of the CPSW
Ethernet Switch. Thus, enable it by adding SGMII mode to the list of the
corresponding extra_modes member.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230309063514.398705-3-s-vadapalli@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support to configure the CPSW MAC's PHY in SGMII mode if the SoC
supports it. The extra_modes member of the phy_gmii_sel_soc_data struct
corresponding to the SoC is used to determine whether or not the SoC
supports SGMII mode.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230309063514.398705-2-s-vadapalli@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Convert platform_get_resource(),devm_ioremap_resource() to a single
call to devm_platform_ioremap_resource(), as this is exactly what this
function does.
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/20230428052758.38636-1-yang.lee@linux.alibaba.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Update kerneldoc of struct qcom_snps_hsphy to fix:
drivers/phy/qualcomm/phy-qcom-snps-femto-v2.c:135: warning: Function parameter or member 'update_seq_cfg' not described in 'qcom_snps_hsphy'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230507144818.193039-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
gcc on aarch64 reports
drivers/phy/mediatek/phy-mtk-hdmi-mt8195.c: In function ‘mtk_hdmi_pll_set_rate’:
drivers/phy/mediatek/phy-mtk-hdmi-mt8195.c:240:52: error: ‘-mgeneral-regs-only’
is incompatible with the use of floating-point types
240 | else if (tmds_clk >= 54 * MEGA && tmds_clk < 148.35 * MEGA)
Floating point should not be used, so rework the floating point comparisons
to fixed point.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20230502145005.2927101-1-trix@redhat.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Support for inno-usb2-phy on Hi3798MV100 was added into existing driver,
while Hi3798MV100 is a A9 ARM32-only SoC.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Link: https://lore.kernel.org/r/20230509060449.1151113-3-mmyangfl@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Adopt existing phy-hisi-inno-usb2 driver to Hi3798MV100, with a slightly
different TEST register convention.
Signed-off-by: David Yang <mmyangfl@gmail.com>
Link: https://lore.kernel.org/r/20230509060449.1151113-2-mmyangfl@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Support for the Exynos4212 SoC was originally dropped as there were
no boards using it. We will be adding a device that uses it, so add
it back.
This reverts commit fee7e1d50c.
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230501195525.6268-9-aweber.kernel@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Updated USB QMP PHY Init sequence based on HPG for IPQ9574.
Reused clock and reset list from existing targets.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Praveenkumar I <quic_ipkumar@quicinc.com>
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Link: https://lore.kernel.org/r/4f15c21f28e2a1332fbdb04d60641cbbf05c6f15.1683630932.git.quic_varada@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Harshit Mogalapalli