Add initial support for the r7272100 SoC including:
- Single Cortex-A9 CPU Core
- GIC
No static virtual mappings are used, all the components
make use of ioremap(). DT_MACHINE_START is still wrapped
in CONFIG_USE_OF to match other mach-shmobile code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Koelsch base board support making use of 2 GiB of memory,
the r8a7791 SoC with the SCIF0 serial port and CA15 with
CMT timer.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Ryo Kataoka <ryo.kataoka.wt@renesas.com>
[damm@opensource.se: Forward ported to upstream, dropped not-yet-ready SMP/PFC]
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables R-Car sound,
AK4643 (CN19) and AK4554 (CN20/CN21) codec chip
on Bock-W.
But, it supports PIO transfer only at this point.
User can check sound settings (Dip-switch/PFC etc)
via this patch, but will get under/over flow error
when playback/capture.
Because PIO transfer via SSI will be interrupted
"sampling rate" times per 1 second.
DMA transfer will be supported when HPB-DMAC was
enabled on r8a7778.
You will notice strange ALSA sound card HW
numbering on Bock-W board.
This came from AK4554 strange format on playback/capture.
The format on playback/capture is same on "normal" codec chip,
but AK4554 was different.
Because of that, AK4554 playback/capture are
registered as a different sound card.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[horms+renesas@verge.net.au: squashed cleanup of SND_SOC_xxx in
Kconfig by Kuninori Morimoto]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add initial support for the r8a7791 SoC including:
- Single Cortex-A15 CPU Core
- GIC
No static virtual mappings are used, all the components
make use of ioremap(). DT_MACHINE_START is still wrapped
in CONFIG_USE_OF to match other mach-shmobile code.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Ryo Kataoka <ryo.kataoka.wt@renesas.com>
[damm@opensource.se: Forward ported to upstream, dropped not-yet-ready code]
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Lots of cleanup and refactoring and some SMP additions for Renesas
platforms. Due to some inter-dependencies with other arm-soc
branches, this Renesas stuff was separated out for sending after the
other branches were merged.
Highlights:
- remove unused board support and cleanup of unused headers
- refactoring of init and device registration
- simplify IRQ initialization
Conflicts: Too many. Most of these are because Simon chose to send
some board updates through the V4L tree that ends up colliding with
the main platform changes. We'll work with him on sorting out his
workflow:
- arch/arm/boot/dts/r8a7740.dtsi:
- Add/add conflict in a devicetree file (keep both)
- arch/arm/mach-shmobile/Makefile:
- Splitting out of clock files collides with intc move to DT.
Keep HEAD version but remove intc-* files for R8A7740 and R8A7779.
- arch/arm/mach-shmobile/board-bockw.c:
- Keep HEAD but remove i2c, hspi and mmc device init calls
- arch/arm/mach-shmobile/board-marzen.c
- Remove mach/hardware.h include and r8a7779_add_usb_phy_device() call,
everything else stays.
- arch/arm/mach-shmobile/include/mach/r8a7778.h:
- From HEAD, Keep camera-rcar.h include and r8a7778_add_vin_device()
- From branch, keep everything
- arch/arm/mach-shmobile/include/mach/r8a7779.h:
- From HEAD, Keep only camera-rcar.h include and r8a7779_add_vin_device()
- arch/arm/mach-shmobile/setup-r8a7778.c
- Keep HEAD, but drop the MMC section (struct resource + add_mmc_device())
- take the new function name from our side (r8a7778_add_dt_devices())
- arch/arm/mach-shmobile/setup-r8a7779.c
- Keep HEAD, but drop r8a7779_add_usb_phy_device()
I've also pushed a test-merge2 branch where you can see how I resolved
them.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Fagt
-----END PGP SIGNATURE-----
Merge tag 'renesas-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM Renesas SoC cleanup, refactoring and more SMP support from Kevin Hilman:
"Lots of cleanup and refactoring and some SMP additions for Renesas
platforms. Due to some inter-dependencies with other arm-soc
branches, this Renesas stuff was separated out for sending after the
other branches were merged.
Highlights:
- remove unused board support and cleanup of unused headers
- refactoring of init and device registration
- simplify IRQ initialization"
* tag 'renesas-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (68 commits)
ARM: shmobile: Per-CPU SMP boot / sleep code for SCU SoCs
ARM: shmobile: Introduce per-CPU SMP boot / sleep code
ARM: shmobile: Use shared SCU CPU Hotplug code on r8a7779
ARM: shmobile: Use shared SCU CPU Hotplug code on sh73a0
ARM: shmobile: Add shared SCU CPU Hotplug code
ARM: shmobile: Use shared SCU SMP boot code on emev2
ARM: shmobile: Use shared SCU SMP boot code on r8a7779
ARM: shmobile: Use shared SCU SMP boot code on sh73a0
ARM: shmobile: Introduce shared SCU SMP boot code
ARM: shmobile: sh73a0: Remove global GPIO_NR definition
ARM: shmobile: kzm9d: remove nfsroot settings from bootargs
ARM: shmobile: armadillo800eva: remove nfsroot settings from bootargs
ARM: shmobile: r8a7779: move r8a7779_init_irq_xxx() to setup
ARM: shmobile: r8a7740: move r8a7740_init_irq_of() to setup
ARM: shmobile: bockw: add missing __initdata
ARM: shmobile: r8a7790: add missing __initdata
ARM: shmobile: r8a7779: add missing __initdata
ARM: shmobile: Remove unused shmobile_init_time()
ARM: shmobile: Use clocksource_of_init() on r8a7790
ARM: shmobile: Use default ->init_time() on KZM9G DT ref
...
Board updates for 3.12. Again, a bit of domain overlap with SoC and DT branches,
but most of this is around legacy code and board support. We've found that
platform maintainers have a hard time separating all of these out and might
move towards fewer branches for next release.
- Removal of a number of Marvell Kirkwood board files, since contents
is now common and mostly configured via DT.
- Device-tree updates for Marvell Dove, including irqchip and clocksource
setup.
- Defconfig updates. Gotta go somewhere. One new one for Renesas Lager.
- New backlight drivers for backlights used on Renesas shmobile platforms.
- Removal of Renesas leds driver.
- Shuffling of some of the new Broadcom platforms to give room for others in
the same mach directory. More in 2.13.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=EGua
-----END PGP SIGNATURE-----
Merge tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board updates from Olof Johansson:
"Board updates for 3.12. Again, a bit of domain overlap with SoC and
DT branches, but most of this is around legacy code and board support.
We've found that platform maintainers have a hard time separating all
of these out and might move towards fewer branches for next release.
- Removal of a number of Marvell Kirkwood board files, since contents
is now common and mostly configured via DT.
- Device-tree updates for Marvell Dove, including irqchip and
clocksource setup.
- Defconfig updates. Gotta go somewhere. One new one for Renesas
Lager.
- New backlight drivers for backlights used on Renesas shmobile
platforms.
- Removal of Renesas leds driver.
- Shuffling of some of the new Broadcom platforms to give room for
others in the same mach directory. More in 3.13"
* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (67 commits)
mmc: sdhci-bcm-kona: Staticize sdhci_bcm_kona_card_event
mmc: sdhci-bcm-kona: Remove unneeded version.h inclusion
ARM: bcm: Make secure API call optional
ARM: DT: binding fixup to align with vendor-prefixes.txt (drivers)
ARM: mmc: fix NONREMOVABLE test in sdhci-bcm-kona
ARM: bcm: Rename board_bcm
mmc: sdhci-bcm-kona: make linker-section warning go away
ARM: tegra: defconfig updates
ARM: dove: add initial DT file for Globalscale D2Plug
ARM: dove: add GPIO IR receiver node to SolidRun CuBox
ARM: dove: add common pinmux functions to DT
ARM: dove: add cpu device tree node
ARM: dove: update dove_defconfig with SI5351, PCI, and xHCI
arch/arm/mach-kirkwood: Avoid using ARRAY_AND_SIZE(e) as a function argument
ARM: kirkwood: fix DT building and update defconfig
ARM: kirkwood: Remove all remaining trace of DNS-320/325 platform code
ARM: configs: disable DEBUG_LL in bcm_defconfig
ARM: bcm281xx: Board specific reboot code
ARM bcm281xx: Turn on socket & network support.
ARM: bcm281xx: Turn on L2 cache.
...
This branch contains mostly additions and changes to platform enablement
and SoC-level drivers. Since there's sometimes a dependency on device-tree
changes, there's also a fair amount of those in this branch.
Pieces worth mentioning are:
- Mbus driver for Marvell platforms, allowing kernel configuration
and resource allocation of on-chip peripherals.
- Enablement of the mbus infrastructure from Marvell PCI-e drivers.
- Preparation of MSI support for Marvell platforms.
- Addition of new PCI-e host controller driver for Tegra platforms
- Some churn caused by sharing of macro names between i.MX 6Q and 6DL
platforms in the device tree sources and header files.
- Various suspend/PM updates for Tegra, including LP1 support.
- Versatile Express support for MCPM, part of big little support.
- Allwinner platform support for A20 and A31 SoCs (dual and quad Cortex-A7)
- OMAP2+ support for DRA7, a new Cortex-A15-based SoC.
The code that touches other architectures are patches moving
MSI arch-specific functions over to weak symbols and removal of
ARCH_SUPPORTS_MSI, acked by PCI maintainers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=fJ5x
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"This branch contains mostly additions and changes to platform
enablement and SoC-level drivers. Since there's sometimes a
dependency on device-tree changes, there's also a fair amount of
those in this branch.
Pieces worth mentioning are:
- Mbus driver for Marvell platforms, allowing kernel configuration
and resource allocation of on-chip peripherals.
- Enablement of the mbus infrastructure from Marvell PCI-e drivers.
- Preparation of MSI support for Marvell platforms.
- Addition of new PCI-e host controller driver for Tegra platforms
- Some churn caused by sharing of macro names between i.MX 6Q and 6DL
platforms in the device tree sources and header files.
- Various suspend/PM updates for Tegra, including LP1 support.
- Versatile Express support for MCPM, part of big little support.
- Allwinner platform support for A20 and A31 SoCs (dual and quad
Cortex-A7)
- OMAP2+ support for DRA7, a new Cortex-A15-based SoC.
The code that touches other architectures are patches moving MSI
arch-specific functions over to weak symbols and removal of
ARCH_SUPPORTS_MSI, acked by PCI maintainers"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (266 commits)
tegra-cpuidle: provide stub when !CONFIG_CPU_IDLE
PCI: tegra: replace devm_request_and_ioremap by devm_ioremap_resource
ARM: tegra: Drop ARCH_SUPPORTS_MSI and sort list
ARM: dts: vf610-twr: enable i2c0 device
ARM: dts: i.MX51: Add one more I2C2 pinmux entry
ARM: dts: i.MX51: Move pins configuration under "iomuxc" label
ARM: dtsi: imx6qdl-sabresd: Add USB OTG vbus pin to pinctrl_hog
ARM: dtsi: imx6qdl-sabresd: Add USB host 1 VBUS regulator
ARM: dts: imx27-phytec-phycore-som: Enable AUDMUX
ARM: dts: i.MX27: Disable AUDMUX in the template
ARM: dts: wandboard: Add support for SDIO bcm4329
ARM: i.MX5 clocks: Remove optional clock setup (CKIH1) from i.MX51 template
ARM: dts: imx53-qsb: Make USBH1 functional
ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module
ARM i.MX6Q: dts: Enable SPI NOR flash on Phytec phyFLEX-i.MX6 Ouad module
ARM: dts: imx6qdl-sabresd: Add touchscreen support
ARM: imx: add ocram clock for imx53
ARM: dts: imx: ocram size is different between imx6q and imx6dl
ARM: dts: imx27-phytec-phycore-som: Fix regulator settings
ARM: dts: i.MX27: Remove clock name from CPU node
...
Convert the marzen board to use DT_MACHINE_START. With this in
place all mach-shmobile boards use DT_MACHINE_START. Also, this
makes it possible for the r8a7779 SMP code to use DT for CPUs.
Signed-off-by: Magnus Damm <damm@opensource.se>
[horms+renesas@verge.net.au: Select USE_OF in Kconfig]
[horms+renesas@verge.net.au: Provide dt_compat in DT_MACHINE_START]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds a sample DT-based Bock-W "reference" implementation.
The use of platform-specific C-code should be avoided
with this configuration as much as possible.
This patch adds new r8a7778_add_dt_devices() which was same stance
of r8a7790_add_dt_devices()
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove support for the sh73a0 based ag5evm board.
The sh73a0 SoC is continued to be supported using
the kzm9g board.
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove support for the sh73a0 based kota2 board.
The sh73a0 SoC is continued to be supported using
the kzm9g board.
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Move the timer configuration bits to allow use in
case of ARCH_SHMOBILE or ARCH_SHMOBILE_MULTI.
The timers all make use of the regular driver model
so they are safe to enable for ARCH_MULTIPLATFORM.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable build of EMEV2 and KZM9D DT Reference in
case of ARCH_MULTIPLATFORM and ARCH_SHMOBILE_MULTI.
IS_ENABLED() is leaves the clock-emev2.c file out
in case of COMMON_CLK=y.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add ARCH_SHMOBILE_MULTI to mach-shmobile that can be used
to enable ARCH_MULTIPLATFORM on selected SoCs and boards.
The headers stay under arch/arm/mach-shmobile/include/mach/
for now, they can and will be migrated independently over time.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
34767f8dcc
(ARM: mach-shmobile: select the fixed regulator driver on several boards)
decided to select fixed regulator driver on Kconfig.
BockW follows same style.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[horms+renesas@verge.net.au: Change mach-shmobile to shmobile in changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This is sufficient to allow boot of the Lager board with
a console without boards-lager.c compiled into the kernel.
This is an example of a minimal but still useful initialisation
of the board using DT as much as possible.
As such it is the same as the boot of Lager that can be achieved
without a board file. The intention of adding this file
is to facilitate further work to allow board specific devices to be
initialised via DT.
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds a sample DT-based APE6EVM "reference" implementation. The
use of platform-specific C-code should be avoided with this configuration
as much as possible.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update the r8a73a4 code to allow using other
timers than Arch timer for clock event
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update the r8a7790 code to allow using other
timers than Arch timer for clock events.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds support for the Z-clock on r8a73a4 SoCs, which is driving
the Cortex A15 core, and a "cpufreq-cpu0" platform device. Adding an
"operating-points" property to the CPU0 DT node and a regulator, this
patch allows platforms to use the generic cpufreq-cpu0 driver to use
SoC's DVFS capabilities.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a DT reference implementation for the KZM9D board.
Only DT devices are used in this case. UART, STI, GPIO
and SMP / GIC are all provided by emev2.dtsi.
There is still a board specific C file used for enabling
legacy SH clocks. This file will be removed after we have
moved over to common clocks.
Signed-off-by: Magnus Damm <damm@opensource.se>
[horms+renesas@verge.net.au: Do not include trailing blank line in
board-kzm9d-reference.c ]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Pull ARM updates from Russell King:
"This contains the usual updates from other people (listed below) and
the usual random muddle of miscellaneous ARM updates which cover some
low priority bug fixes and performance improvements.
I've started to put the pull request wording into the merge commits,
which are:
- NoMMU stuff:
This includes the following series sent earlier to the list:
- nommu-fixes
- R7 Support
- MPU support
I've left out the ARCH_MULTIPLATFORM/!MMU stuff that Arnd and I
were discussing today until we've reached a conclusion/that's had
some more review.
This is rebased (and re-tested) on your devel-stable branch because
otherwise there were going to be conflicts with Uwe's V7M work now
that you've merged that. I've included the fix for limiting MPU to
CPU_V7.
- Huge page support
These changes bring both HugeTLB support and Transparent HugePage
(THP) support to ARM. Only long descriptors (LPAE) are supported
in this series.
The code has been tested on an Arndale board (Exynos 5250).
- LPAE updates
Please pull these miscellaneous LPAE fixes I've been collecting for
a while now for 3.11. They've been tested and reviewed by quite a
few people, and most of the patches are pretty trivial. -- Will Deacon.
- arch_timer cleanups
Please pull these arch_timer cleanups I've been holding onto for a
while. They're the same as my last posting, but have been rebased
to v3.10-rc3.
- mpidr linearisation (multiprocessor id register - identifies which
CPU number we are in the system)
This patch series that implements MPIDR linearization through a
simple hashing algorithm and updates current cpu_{suspend}/{resume}
code to use the newly created hash structures to retrieve context
pointers. It represents a stepping stone for the implementation of
power management code on forthcoming multi-cluster ARM systems.
It has been tested on TC2 (dual cluster A15xA7 system), iMX6q,
OMAP4 and Tegra, with processors hitting low-power states requiring
warm-boot resume through the cpu_resume code path"
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (77 commits)
ARM: 7775/1: mm: Remove do_sect_fault from LPAE code
ARM: 7777/1: Avoid extra calls to the C compiler
ARM: 7774/1: Fix dtb dependency to use order-only prerequisites
ARM: 7770/1: remove residual ARMv2 support from decompressor
ARM: 7769/1: Cortex-A15: fix erratum 798181 implementation
ARM: 7768/1: prevent risks of out-of-bound access in ASID allocator
ARM: 7767/1: let the ASID allocator handle suspended animation
ARM: 7766/1: versatile: don't mark pen as __INIT
ARM: 7765/1: perf: Record the user-mode PC in the call chain.
ARM: 7735/2: Preserve the user r/w register TPIDRURW on context switch and fork
ARM: kernel: implement stack pointer save array through MPIDR hashing
ARM: kernel: build MPIDR hash function data structure
ARM: mpu: Ensure that MPU depends on CPU_V7
ARM: mpu: protect the vectors page with an MPU region
ARM: mpu: Allow enabling of the MPU via kconfig
ARM: 7758/1: introduce config HAS_BANDGAP
ARM: 7757/1: mm: don't flush icache in switch_mm with hardware broadcasting
ARM: 7751/1: zImage: don't overwrite ourself with a page table
ARM: 7749/1: spinlock: retry trylock operation if strex fails on free lock
ARM: 7748/1: oabi: handle faults when loading swi instruction from userspace
...
These changes from 30 individual branches for the most part update device
tree files, but there are also a few source code changes that have crept
in this time, usually in order to atomically move over a driver from
using hardcoded data to DT probing.
A number of platforms change their DT files to use the C preprocessor,
which is causing a bit of churn, but that is hopefully only this once.
There are a few conflicts with the other branches unfortunately:
* in exynos5440.dtsi and kirkwood-6281.dtsi, device nodes are added
from multiple branches. Need to be careful to have the right
set of closing braces as git gets this one wrong.
* In kirkwood.dtsi, one 'ranges' line got split into two lines, while
another line got added. Order of the lines does not matter.
* in sama5d3.dtsi, some cleanup was merged the wrong way, causing
a bogus conflict. We want the 'dmas' and 'dma-names' properties
to get added here.
* Two lines got removed independently in arch/arm/mach-mxs/mach-mxs.c
* Contents get added independently in arch/arm/mach-omap2/cclock33xx_data.c
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=8PtJ
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree changes from Arnd Bergmann:
"These changes from 30 individual branches for the most part update
device tree files, but there are also a few source code changes that
have crept in this time, usually in order to atomically move over a
driver from using hardcoded data to DT probing.
A number of platforms change their DT files to use the C preprocessor,
which is causing a bit of churn, but that is hopefully only this once"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (372 commits)
ARM: at91: dt: rm9200ek: add spi support
ARM: at91: dt: rm9200: add spi support
ARM: at91/DT: at91sam9n12: add SPI DMA client infos
ARM: at91/DT: sama5d3: add SPI DMA client infos
ARM: at91/DT: fix SPI compatibility string
ARM: Kirkwood: Fix the internal register ranges translation
ARM: dts: bcm281xx: change comment to C89 style
ARM: mmc: bcm281xx SDHCI driver (dt mods)
ARM: nomadik: add the new clocks to the device tree
clk: nomadik: implement the Nomadik clocks properly
ARM: dts: omap5-uevm: Provide USB Host PHY clock frequency
ARM: dts: omap4-panda: Fix DVI EDID reads
ARM: dts: omap4-panda: Add USB Host support
arm: mvebu: enable mini-PCIe connectors on Armada 370 RD
ARM: shmobile: irqpin: add a DT property to enable masking on parent
ARM: dts: AM43x EPOS EVM support
ARM: dts: OMAP5: Add bandgap DT entry
ARM: dts: AM33XX: Add pinmux configuration for CPSW to am335x EVM
ARM: dts: AM33XX: Add pinmux configuration for CPSW to EVMsk
ARM: dts: AM33XX: Add pinmux configuration for CPSW to beaglebone
...
Work by Magnus Damm and others to clean up the boot of and move
things closer to supporting multi-arch.
As a side effect of this work it was decided to remove support for
two boards, Bonito and AP4EVB. Those patches are included in this
series as they depend on earlier patches in the series.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=1+Oa
-----END PGP SIGNATURE-----
Merge tag 'renesas-cleanup-boot-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
From Simon Horman:
Renesas ARM based SoC boot cleanup for v3.11
Work by Magnus Damm and others to clean up the boot of and move
things closer to supporting multi-arch.
As a side effect of this work it was decided to remove support for
two boards, Bonito and AP4EVB. Those patches are included in this
series as they depend on earlier patches in the series.
* tag 'renesas-cleanup-boot-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Remove Bonito board support
ARM: shmobile: Remove AP4EVB board support
ARM: shmobile: Remove mach/memory.h
ARM: shmobile: Remove MEMORY_START/SIZE
ARM: shmobile: Enable ARM_PATCH_PHYS_VIRT
ARM: shmobile: Remove old SCU boot code
ARM: shmobile: EMEV2 SMP with SCU boot fn and args
ARM: shmobile: sh73a0 SMP with SCU boot fn and args
ARM: shmobile: r8a7779 SMP with SCU boot fn and args
ARM: shmobile: Add SCU boot function using argument
ARM: shmobile: Add SMP boot function and argument
ARM: shmobile: Rework sh7372 sleep code to use virt_to_phys()
ARM: shmobile: Remove romImage CONFIG_MEMORY_START
ARM: shmobile: Let romImage rely on default ATAGS
ARM: shmobile: uImage load address rework
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Remove board support for the r8a7740 based Bonito board
The r8a7740 SoC support code is still kept around since it
is in use by the Armadillo800eva board which is basically a more
recent board where the design is based on Bonito.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove board support for the sh7372 based AP4EVB board
The sh7372 SoC support code is still kept around since it
is in use by the Mackerel board which is basically a more
recent board where the design is based on AP4EVB.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove CONFIG_MEMORY_START and CONFIG_MEMORY_SIZE from mach-shmobile.
Boards should use DT to specify their memory setup. Boards that still
not support DT may pass ATAGS with memory information from the boot
loader. If those ATAGS turn out to be incorrect then appended DTB with
memory information should be used as a workaround.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add USB clock and EHCI, OHCI, and USB PHY platform devices for R8A7778 SoC; add
a function to register PHY device with board-specific platform data and register
EHCI and OHCI platfrom devices from the init_late() board method.
Also, don't forget to enable CONFIG_ARCH_HAS_[EO]HCI options for R8A7778 SoC in
Kconfig...
The patch has been tested on the BOCK-W board.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This branch acts as a base for adding USB support to
r8A7778/BOCK-W and r8A7779/Marzen.
It includes the soc branch to provide dependencies in
the r8A7778 clock code.
It includes pinmux to provide pinmux initialisation for Bock-W
which is a dependency.
Conflicts:
arch/arm/mach-shmobile/Kconfig
arch/arm/mach-shmobile/include/mach/r8a7778.h
arch/arm/mach-shmobile/setup-r8a7778.c
In 8a4da6e: "arm: arch_timer: move core to drivers/clocksource", the
selection of ARM_ARCH_TIMER was indirected via HAVE_ARM_ARCH_TIMER,
though mach-exynos's selection of ARM_ARCH_TIMER was missed, and since
then mach-shmobile, mach-tegra, and mach-virt have begun selecting
ARM_ARCH_TIMER. This can lead to architected timer support erroneously
appearing to not be selected in menuconfig.
This patch fixes up the Kconfigs for those platforms to select
HAVE_ARM_ARCH_TIMER.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
This patch enables the use of the generic cpufreq-cpu0 driver on sh73a0.
Providing a regulator, a list of OPPs in DT, combined with a virtual
cpufreq-cpu0 platform device and a clock, attached to it is everything,
the cpufreq-cpu0 driver needs. The first sh73a0 platform, implementing
such CPUFreq support is kzm9g-reference.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The correct model name is R-Car M1A or R8A77781; R8A77780 corresponds to R-Car
M1S which is a SH based SoC.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[horms+renesas@verge.net.au: manually applied]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Provide alternate board code for the Armadillo800EVA to demonstrate how
DT may be used given the current state of driver device tree support.
This is intended to act as a reference for mach-shmobile developers.
This a rather bare bone version with the following devices supported:
- GIC
- irqpins
- i2c0/1
- touchscreen
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds SMSC ethernet support on Bock-W
Bock-W SMSC needs FPGA settings which enables interrupt.
This patch does it on bockw_init() function.
As notes for future, this FPGA settings should be updated,
since this FPGA is using cascaded interrupt.
Current code is assuming that this FPGA interrupt user is only SMSC.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Lager base board support making use of 2 GiB of memory,
the r8a7790 SoC with the SCIF0 serial port and CA15 with
ARM architected timer.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
V3 of APE6EVM base board support making use of
1 GiB of memory, the SCIFA0 serial port and
ARM architected timer.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add basic Bock-W board support
More devices will be added on top of this patch after
PICNTRL and clock framework are in better shape.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Highlights:
* Compilation fixes for sh7269 and for when CONFIG_BUG is not set
* sh-pfc Support for r8a73a4 SoC
* Move GPIOs handling from the PFC device to separate GPIO devices on the r8a7779 SoC
This pull request is based on a merge of:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-pinmux-for-v3.10
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-soc2-for-v3.10
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=vwDo
-----END PGP SIGNATURE-----
Merge tag 'renesas-pinmux2-for-v3.10' into boards-base
Second round of Renesas ARM and SH based SoC pinmux updates for v3.10
Highlights:
* Compilation fixes for sh7269 and for when CONFIG_BUG is not set
* sh-pfc Support for r8a73a4 SoC
* Move GPIOs handling from the PFC device to separate GPIO devices on the r8a7779 SoC
This pull request is based on a merge of:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-pinmux-for-v3.10
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas renesas-soc2-for-v3.10
This merge is made to supply run-time dependencies for the following
patches that will bea added on top:
ARM: shmobile: APE6EVM LAN9220 support
ARM: shmobile: APE6EVM PFC support
Add IRQC interrupt controller support to r8a7790 by
hooking up a single IRQC instances to handle 4 external
IRQ signals. The IRQC controller is tied to SPIs of
the GIC. On r8a7790 the external IRQ pins routing is
handled by the PFC which is excluded from this patch.
Both platform devices and DT devices are added in this
patch. The platform device versions are used to provide
a static interrupt map configuration for board code
written in C.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add initial support for the r8a7790 SoC including:
- Single Cortex-A15 CPU Core
- GIC
- Architecture timer
No static virtual mappings are used, all the components
make use of ioremap(). DT_MACHINE_START is still wrapped
in CONFIG_USE_OF to match other mach-shmobile code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
With the added capabilty of the intc_irqpin driver to handle shared
external IRQs, all prerequisites are fulfilled and we are ready to
migrate completely to GIC. This includes the following steps:
- Kconfig: select ARM_GIC and RENESAS_INTC_IRQPIN
- intc-r8a7740: Throw out all legacy INTC code and init the GIC. We need
to mask out all shared IRQs as it is needed by the
shared intc_irqpin driver.
- setup-r8a7740: Add 4 irqpin devices to handle external IRQs and update
all IRQ numbers to point to the GIC SPI.
- board-armadillo: Update all IRQ numbers to point to the GIC SPI.
- pfc-r8a7740: Update all IRQ numbers of the GPIOs to point to the GIC
SPI.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add initial support for the R8A7778 R-Car M1A SoC.
No static virtual mappings are used, all the components
make use of ioremap().
DT_MACHINE_START is still wrapped
in CONFIG_USE_OF to match other mach-shmobile code.
It is based on v1.0 datasheet
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add IRQC interrupt controller support to r8a73a4 by
hooking up two IRQC instances to handle 58 external
IRQ signals. There IRQC controllers are tied to SPIs
of the GIC. On r8a73a4 exact IRQ pin routing is handled
by the PFC which is excluded from this patch.
Both platform devices and DT devices are added in this
patch. The platform device versions are used to provide
a static interrupt map configuration for board code
written in C.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
V3 of initial support for the r8a73a4 SoC including:
- Single Cortex-A15 CPU Core
- GIC
- Architecture timer
No static virtual mappings are used, all the components
make use of ioremap(). DT_MACHINE_START is still wrapped
in CONFIG_USE_OF to match other mach-shmobile code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reference kernel configurations for armadillo800eva and kzm9g boards do not
have to depend on their respective "legacy" configurations, doing device
instantiation in .c, they can be configured and built independently.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
[horms+renesas@verge.net.au: created separate patch for kzm9g portion]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Provide alternate board code for the kzm9g to demonstrate
how DT may be used given the current state of driver
device tree support. This is intended to act as a reference
for mach-shmobile developers.
Some notes:
* Brings up the GIC interrupt handler using device tree
* Brings up the following device using device tree:
- MMCIF (MMC)
* Does not bring up the INTC interrupt controller at all,
thus external devices may not be used. In particular,
the SMSC ethernet device may not be used and thus
NFS root may not be used.
* Uses existing C code and not device tree to initialise the following,
which are needed for a working board:
- SCIF (Serial)
- CMT (Clock)
- PFC (GPIO)
To use this alternate board code instead of the normal board code,
CONFIG_MACH_KZM9G_REFERENCE should be selected in the kernel config.
And the sh73a0-kzm9g-reference.dtb flattened device tree blob should be used.
Includes fix by Thierry Reding to no longer use gic_handle_irq()
Includes fixes by Guennadi Liakhovetski for recent pinmux changes.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Provide alternate board code for the marzen to demonstrate
how DT may be used given the current state of driver
device tree support. This is intended to act as a reference
for mach-shmobile developers.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update the r8a7779 IRQ code to make use of the
INTC External IRQ pin driver for external
interrupt pins IRQ0 -> IRQ3.
The r8a7779 SoC can like older SH SoCs configure
to use the IRQ0 -> IRQ3 signals as individual
interrupts or a combined IRL mode.
Without this patch the r8a7779 SoC code does
not fully support external IRQ pins in individual
IRQ mode. The r8a7779 PFC code does not yet have
gpio_to_irq() support so no need to update such
code.
At this point the DT reference implementations
are not covered. In the future such code shall
tie in the INTC External IRQ pin driver via
DT, so this kind of verbose code is not needed
for the long term DT case.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adjust the sh73a0 IRQ code to make use of the
INTC External IRQ pin driver for external
interrupt pins IRQ0 -> IRQ31.
This removes quite a bit of special-case code
in intc-sh73a0.c but the number of lines get
replaced with platform device information in
setup-sh73a0.c. The PFC code is also adjusted
to make gpio_to_irq() return the correct
interrupt number.
At this point the DT reference implementations
are not covered. In the future such code shall
tie in the INTC External IRQ pin driver via
DT, so this kind of verbose code is not needed
for the long term DT case.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch supports CN21/CN22 USB 1.x (port 0/1/2),
and enable input event on defconfig
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
This patch supports CN21/CN22 USB 2.0 (port 0/1/2),
and enable USB momery on defconfig
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
This is old CPU of shmobile, and the machine by which this CPU is
used cannot be obtained.
Therefore, remove SH7377 support.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
This is old CPU of shmobile, and the machine by which this CPU is
used cannot be obtained.
Therefore, remove SH7367 support.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
This machine is using old CPU of shmobile (sh7377) and cannot obtain
machine, either.
Therefore, remove G4EVM support.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
This machine is using old CPU of shmobile (SH7367) and cannot obtain
machine, either.
Therefore, remove G3EVM support.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Use DT_MACHINE_START() on the sh7372 based mackerel board.
Also include a tiny DTS file to describe the board and update the
Kconfig dependencies to select CONFIG_USE_OF.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
As suggested by Andrew Morton:
This is a pet peeve of mine. Any time there's a long list of items
(header file inclusions, kconfig entries, array initalisers, etc) and
someone wants to add a new item, they *always* go and stick it at the
end of the list.
Guys, don't do this. Either put the new item into a randomly-chosen
position or, probably better, alphanumerically sort the list.
lets sort all our select statements alphanumerically. This commit was
created by the following perl:
while (<>) {
while (/\\\s*$/) {
$_ .= <>;
}
undef %selects if /^\s*config\s+/;
if (/^\s+select\s+(\w+).*/) {
if (defined($selects{$1})) {
if ($selects{$1} eq $_) {
print STDERR "Warning: removing duplicated $1 entry\n";
} else {
print STDERR "Error: $1 differently selected\n".
"\tOld: $selects{$1}\n".
"\tNew: $_\n";
exit 1;
}
}
$selects{$1} = $_;
next;
}
if (%selects and (/^\s*$/ or /^\s+help/ or /^\s+---help---/ or
/^endif/ or /^endchoice/)) {
foreach $k (sort (keys %selects)) {
print "$selects{$k}";
}
undef %selects;
}
print;
}
if (%selects) {
foreach $k (sort (keys %selects)) {
print "$selects{$k}";
}
}
It found two duplicates:
Warning: removing duplicated S5P_SETUP_MIPIPHY entry
Warning: removing duplicated HARDIRQS_SW_RESEND entry
and they are identical duplicates, hence the shrinkage in the diffstat
of two lines.
We have four testers reporting success of this change (Tony, Stephen,
Linus and Sekhar.)
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* renesas-board-common:
ARM: mach-shmobile: select the fixed regulator driver on several boards
regulator: extend the fixed dummy voltage regulator to accept voltage
regulator: support multiple dummy fixed regulators
Conflicts:
arch/arm/mach-shmobile/Kconfig
* renesas-soc: (31 commits)
ARM: shmobile: Fix build problem in pm-sh7372.c for unusual .config
ARM: shmobile: Take cpuidle dependencies into account correctly
ARM: mach-shmobile: sh7377 generic board support via DT
ARM: mach-shmobile: r8a7740 generic board support via DT
ARM: shmobile: sh7372: completely switch over to using pm-rmobile API
ARM: shmobile: ap4evb: switch to using pm-rmobile API
ARM: shmobile: mackerel: switch to using pm-rmobile API
ARM: shmobile: sh7372: add pm-rmobile domain support
ARM: shmobile: r8a7740: add A4LC pm domain support
ARM: shmobile: r8a7740: add A3SP pm domain support
ARM: shmobile: r8a7740: add A4S pm domain support
ARM: shmobile: r8a7740: fixup: MSEL1CR 7bit control
ARM: shmobile: soc-core: add R-mobile PM domain common APIs
ARM: shmobile: sh7372 A3SM CPUIdle support
ARM: shmobile: Use INTCA with sh7372 A3SM power domain
ARM: mach-shmobile: Convert sh_clk_mstp32_register to sh_clk_mstp_register
ARM: shmobile: use common DMAEngine definitions on sh7372
ARM: shmobile: use common DMAEngine definitions on sh73a0
ARM: shmobile: sh73a0: add DMAEngine support for MPDMAC
ARM: shmobile: sh73a0: add USB clock support
...
The sh7372's cpuidle code uses cpu_suspend() and cpu_resume() in
its implementation of the .enter() callback for deeper C-states, so
make ARCH_SH7372 select ARM_CPU_SUSPEND if CPU_IDLE is set to satisfy
all of the build dependencies (it has to be selected for CONFIG_PM
as well for the system suspend handling).
[rjw: Added the subject and changelog.]
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
On systems, using regulators to supply power to devices, if the REGULATOR
Kconfig option is disabled, regulator API stubs will be used, which often
suffices to bring a default configuration up. If REGULATOR is enabled but
respective regulator drivers are inactive, the real regulator API calls
will be used, which in the absence of drivers will fail to provide
services. This patch prevents such a problem on sh-mobile boards by
forcing REGULATOR_FIXED_VOLTAGE on if REGULATOR is selected.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch enable sound support on CON11
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch enable sound playback/capture on CN9/CN10.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This is the first big chunk for 3.5 merges of sound stuff.
There are a few big changes in different areas. First off, the
streaming logic of USB-audio endpoints has been largely rewritten
for the better support of "implicit feedback". If anything about USB
got broken, this change has to be checked.
For HD-audio, the resume procedure was changed; instead of delaying
the resume of the hardware until the first use, now waking up immediately
at resume. This is for buggy BIOS.
For ASoC, dynamic PCM support and the improved support for digital links
between off-SoC devices are major framework changes.
Some highlights are below:
* HD-audio
- Avoid the accesses of invalid pin-control bits that may stall the codec
- V-ref setup cleanups
- Fix the races in power-saving code
- Fix the races in codec cache hashes and connection lists
- Split some common codes for BIOS auto-parser to hda_auto_parser.c
- Changed the PM resume code to wake up immediately for buggy BIOS
- Creative SoundCore3D support
- Add Conexant CX20751/2/3/4 codec support
* ASoC
- Dynamic PCM support, allowing support for SoCs with internal routing
through components with tight sequencing and formatting constraints
within their internal paths or where there are multiple components
connected with CPU managed DMA controllers inside the SoC.
- Greatly improved support for direct digital links between off-SoC
devices, providing a much simpler way of connecting things like digital
basebands to CODECs.
- Much more fine grained and robust locking, cleaning up some of the
confusion that crept in with multi-component.
- CPU support for nVidia Tegra 30 I2S and audio hub controllers and
ST-Ericsson MSP I2S controolers
- New CODEC drivers for Cirrus CS42L52, LAPIS Semiconductor ML26124, Texas
Instruments LM49453.
- Some regmap changes needed by the Tegra I2S driver.
- mc13783 audio support.
* Misc
- Rewrite with module_pci_driver()
- Xonar DGX support for snd-oxygen
- Improvement of packet handling in snd-firewire driver
- New USB-endpoint streaming logic
- Enhanced M-audio FTU quirks and relevant cleanups
- Increment the support of OSS devices to 256
- snd-aloop accuracy improvement
There are a few more pending changes for 3.5, but they will be
sent slightly later as partly depending on the changes of DRM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQIcBAABAgAGBQJPvD/9AAoJEGwxgFQ9KSmkPsIP/AuBGpAZy7b7FiEEIy1Hhdws
US8WVuPzyDslMVdzZ8OFqyPXanIcL9gscoOGMZOEy7UFtMBiR4GuYiPRPubEMxuP
/gopUqK4SqIsIwT238qqYszSJSxE7gNEZ/2jhSGtkX4EkaSZ4bAskn0iOKX5uw2f
kTUQknA1rNLIGba2z6rJbgIW7hdxGfpFy05ruv3ct81nO+5JlgyLuP/v5R6jL+do
cum0N4dJFRd9YSEi2BG612gdz8LJyzOgPqBKmxMEva6BfqLkR8EdP80FtE3eEOiP
Et1q2LhZwOlBt0BEjsjjOVxMsgxVax6ps9cuNRTk5ECEOldU5dbDatC45L/e9mSD
OQVUjYAX1mQAtYva4U4PPn6WU6ma2L5yjy4peCObtyCMkEchXk1bfs4CEfVqCXUP
yFYN8C+y6osZOyWE3+Enn9ifZdWyLeSVq6CT33Yt+fyKlswp6gRkhKYiEPqTA5aU
p71X59Pp7q1y3tQwiMJNpf2QdkxuxfKURHswdc4BS9ct0mdZhQX0GyDS7OffkTd4
Lq5UkVMHA1rLlF9oRPd2C9P4BuMEuvLjf662YCKiw+mWFYdBC036DHLLjm1Hcwuj
UkpQ2PSrrdHG1u0c3ooZ9dQj1BNX4LoABLqvaMtce6sESD/hJ5gcprYJWvtituwM
ZzZiJavIWsoJ+SWQWBHe
=+JSm
-----END PGP SIGNATURE-----
Merge tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This is the first big chunk for 3.5 merges of sound stuff.
There are a few big changes in different areas. First off, the
streaming logic of USB-audio endpoints has been largely rewritten for
the better support of "implicit feedback". If anything about USB got
broken, this change has to be checked.
For HD-audio, the resume procedure was changed; instead of delaying
the resume of the hardware until the first use, now waking up
immediately at resume. This is for buggy BIOS.
For ASoC, dynamic PCM support and the improved support for digital
links between off-SoC devices are major framework changes.
Some highlights are below:
* HD-audio
- Avoid accesses of invalid pin-control bits that may stall the codec
- V-ref setup cleanups
- Fix the races in power-saving code
- Fix the races in codec cache hashes and connection lists
- Split some common codes for BIOS auto-parser to hda_auto_parser.c
- Changed the PM resume code to wake up immediately for buggy BIOS
- Creative SoundCore3D support
- Add Conexant CX20751/2/3/4 codec support
* ASoC
- Dynamic PCM support, allowing support for SoCs with internal
routing through components with tight sequencing and formatting
constraints within their internal paths or where there are multiple
components connected with CPU managed DMA controllers inside the
SoC.
- Greatly improved support for direct digital links between off-SoC
devices, providing a much simpler way of connecting things like
digital basebands to CODECs.
- Much more fine grained and robust locking, cleaning up some of the
confusion that crept in with multi-component.
- CPU support for nVidia Tegra 30 I2S and audio hub controllers and
ST-Ericsson MSP I2S controolers
- New CODEC drivers for Cirrus CS42L52, LAPIS Semiconductor ML26124,
Texas Instruments LM49453.
- Some regmap changes needed by the Tegra I2S driver.
- mc13783 audio support.
* Misc
- Rewrite with module_pci_driver()
- Xonar DGX support for snd-oxygen
- Improvement of packet handling in snd-firewire driver
- New USB-endpoint streaming logic
- Enhanced M-audio FTU quirks and relevant cleanups
- Increment the support of OSS devices to 256
- snd-aloop accuracy improvement
There are a few more pending changes for 3.5, but they will be sent
slightly later as partly depending on the changes of DRM."
Fix up conflicts in regmap (due to duplicate patches, with some further
updates then having already come in from the regmap tree). Also some
fairly trivial context conflicts in the imx and mcx soc drivers.
* tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (280 commits)
ALSA: snd-usb: fix stream info output in /proc
ALSA: pcm - Add proper state checks to snd_pcm_drain()
ALSA: sh: Fix up namespace collision in sh_dac_audio.
ALSA: hda/realtek - Fix unused variable compile warning
ASoC: sh: fsi: enable chip specific data transfer mode
ASoC: sh: fsi: call fsi_hw_startup/shutdown from fsi_dai_trigger()
ASoC: sh: fsi: use same format for IN/OUT
ASoC: sh: fsi: add fsi_version() and removed meaningless version check
ASoC: sh: fsi: use register field macro name on IN/OUT_DMAC
ASoC: tegra: Add machine driver for WM8753 codec
ALSA: hda - Fix possible races of accesses to connection list array
ASoC: OMAP: HDMI: Introduce codec
ARM: mx31_3ds: Add sound support
ASoC: imx-mc13783 cleanup
mx31moboard: Add sound support
ASoC: mc13783 codec cleanups
ASoC: add imx-mc13783 sound support
ASoC: Add mc13783 codec
mfd: mc13xxx: add codec platform data
ASoC: don't flip master of DT-instantiated DAI links
...
While we generally attempt to get rid of board specific files and replace
them with device tree based descriptions, a lot of platforms have not
come that far:
In shmobile, we add two new board files because their recently started
effort to add DT support has not proceeded enough to use it for all of
the important hardware.
In Kirkwood, we are adding support for new boards with a combination of
DT and board file contents in multiple cases.
pxa/mmp and imx are extending support for existing board files but not
adding new ones.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=wkmj
-----END PGP SIGNATURE-----
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc board specific changes from Olof Johansson:
"While we generally attempt to get rid of board specific files and
replace them with device tree based descriptions, a lot of platforms
have not come that far:
In shmobile, we add two new board files because their recently started
effort to add DT support has not proceeded enough to use it for all of
the important hardware.
In Kirkwood, we are adding support for new boards with a combination
of DT and board file contents in multiple cases.
pxa/mmp and imx are extending support for existing board files but not
adding new ones."
Fix up trivial conflicts in arch/arm/mach-{mmp/ttc_dkb.c,shmobile/{Kconfig,Makefile}}
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (94 commits)
ARM: shmobile: fix smp build
ARM: kirkwood: Add support for RaidSonic IB-NAS6210/6220 using devicetree
kirkwood: Add iconnect support
orion/kirkwood: create a generic function for gpio led blinking
kirkwood/orion: fix orion_gpio_set_blink
ARM: kirkwood: Define DNS-320/DNS-325 NAND in fdt
kirkwood: Allow nand to be configured via. devicetree
mtd: Add orion_nand devicetree bindings
ARM: kirkwood: Basic support for DNS-320 and DNS-325
ARM: mach-shmobile: Use DT_MACHINE for armadillo 800 eva
ARM: mach-shmobile: Use DT_MACHINE for KZM9G
ARM: pxa: hx4700: Add Synaptics NavPoint touchpad
ARM: pxa: Use REGULATOR_SUPPLY macro
ARM: mach-shmobile: kzm9g: enable SMP boot
ARM: mach-shmobile: kzm9g: defconfig update
ARM: mach-shmobile: kzm9g: add PCF8757 gpio-key
ARM: mach-shmobile: kzm9g: add SDHI support
ARM: mach-shmobile: kzm9g: add MMCIF support
ARM: mach-shmobile: kzm9g: correct screen direction
ARM: mach-shmobile: sh73a0.h: add GPIO_NR
...
Use DT_MACHINE_START() on the emev2 based KZM9D board.
Also include a tiny DTS file to describe the board and
update the Kconfig dependencies to select CONFIG_USE_OF.
Update the SMP glue code to use OF for matching.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tie in the Emma Mobile GPIO driver "em-gio" to
support the GPIOs on Emma Mobile EV2.
A static IRQ range is used to allow boards to
hook up their platform devices to the GPIOs.
DT support is still on the TODO for the GPIO driver,
so only platform device support is included here.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
V3 of basic KZM9D board support. At this point a quite
thin layer that makes use of the Emma Mobile EV2 SoC code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This is V3 of the Emma Mobile EV2 SoC support.
Included here is support for serial and timer
devices which is just about enough to boot a kernel.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Use DT_MACHINE_START() on the r8a7740 based armadillo 800 eva board.
Also include a tiny DTS file to describe the board and update the
Kconfig dependencies to select CONFIG_USE_OF.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Use DT_MACHINE_START() on the sh73a0 based KZM9G board.
Also include a tiny DTS file to describe the board and
update the Kconfig dependencies to select CONFIG_USE_OF.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This adds very basic KZM-A9-GT board (SH73a0) support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This adds very basic armadillo800eva board (R-Mobile A1) support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch uses simple-card driver instead of fsi-ak4642 on each board.
To select AK4642 driver, each boards select it on Kconfig.
This patch removes fsi-ak4642 driver which is no longer needed
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add GPIO-only r8a7779 PFC support V2.
Only regular GPIOs are supported at this time. GPIO_FN are not
supported because they require variable bit width support in be
the shared pfc code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Initial support for the r8a7779 SoC and the Marzen board (V2).
Only SCIF ports and the TMU are supported at this point.
To keep things simple only entity-mapped virt-to-phys mappings
are supported. This forces drivers and other SoC glue code to
make use of ioremap(). We cannot support early serial console
due to virtual address space collisions with the ARM kernel.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
R8A7740 GIC can not get external IRQx interrupt directly
without GIC - INTC demux support.
Current AG5 is using GIC - INTCS demux with
special irq relocation. but GIC - INTCA demux
is still not supported and it needs irq number re-mapping.
OTOH, normal INTC support as before is very enough for R8A7740,
because it is not SMP CPU.
This patch adds INTCA/INTCS support instead of GIC.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the R8A7740 (R-Mobile A1) CPU
Timer, serial, gic, clock are supported at this point.
This patch is based on v0.1 manual
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
ag5evm implements a backlight control, using an I2C controller, therefore
it needs CONFIG_I2C to fix this make failure
arch/arm/mach-shmobile/built-in.o: In function `lcd_on':
pfc-sh73a0.c:(.text+0x2334): undefined reference to `i2c_get_adapter'
pfc-sh73a0.c:(.text+0x2370): undefined reference to `i2c_transfer'
(ignore pfc-sh73a0.c) and to build successfully.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Kota2 base board support including the on-chip SCIFA2
serial console and the on-board SMSC911X ethernet port.
The s73a0 SMP bits are also updated to include Kota2.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add platform data for MIPI-DSI and LCDC on the AG5EVM
board. The sh73a0 clkdev bindings are also updated.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Because ag5evm board setup code uses gpio functions,
ARCH_REQUIRE_GPIOLIB should be set in Kconfig.
Otherwise, the first build with defconfig fails.
Signed-off-by: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Ag5evm board now uses gpio api to initialize pins and peripherals.
Signed-off-by: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm